Drivers and core code does not modify the file-scope static 'struct
qcom_icc_hws_data', so it can be made const for code safety and
readability.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240905150235.276345-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Unlike MSM platforms that manage NoC related clocks and scaling
from RPM, IPQ SoCs dont involve RPM in managing NoC related
clocks and there is no NoC scaling.
However, there is a requirement to enable some NoC interface
clocks for accessing the peripheral controllers present on
these NoCs. Though exposing these as normal clocks would work,
having a minimalistic interconnect driver to handle these clocks
would make it consistent with other Qualcomm platforms resulting
in common code paths. This is similar to msm8996-cbf's usage of
icc-clk framework.
Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
Link: https://lore.kernel.org/r/20240430064214.2030013-5-quic_varada@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The previous wrapper qcom_cc_really_probe takes the platform
device as parameter, which is limited to platform driver.
As for qca8k clock controller driver, which is registered as
the MDIO device, which also follows the qcom clock framework.
To commonize qcom_cc_really_probe, updating it to take the
struct device as parameter, so that the qcom_cc_really_probe
can be utilized by the previous platform device and the new
added MDIO device.
Also update the current clock controller drivers to take
&pdev->dev as parameter when calling qcom_cc_really_probe.
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Luo Jie <quic_luoj@quicinc.com>
Link: https://lore.kernel.org/r/20240605124541.2711467-4-quic_luoj@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Some RCG frequency can be reached by multiple configuration.
Add clk_rcg2_fm_ops ops to support these special RCG configurations.
These alternative ops will select the frequency using a CEIL policy.
When the correct frequency is found, the correct config is selected by
calculating the final rate (by checking the defined parent and values
in the config that is being checked) and deciding based on the one that
is less different than the requested one.
These check are skipped if there is just one config for the requested
freq.
qcom_find_freq_multi is added to search the freq with the new struct
freq_multi_tbl.
__clk_rcg2_select_conf is used to select the correct conf by simulating
the final clock.
If a conf can't be found due to parent not reachable, a WARN is printed
and -EINVAL is returned.
Tested-by: Wei Lei <quic_leiwei@quicinc.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20231220221724.3822-3-ansuelsmth@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The function mux_get_parent() uses qcom_find_src_index() to find the
parent clock index, which is incorrect: qcom_find_src_index() uses src
enum for the lookup, while mux_get_parent() should use cfg field (which
corresponds to the register value). Add qcom_find_cfg_index() function
doing this kind of lookup and use it for mux parent lookup.
Fixes: df964016490b ("clk: qcom: add parent map for regmap mux")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20211115233407.1046179-1-dmitry.baryshkov@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Extend the probe by index API in common code to be used
by other qcom clock controller.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Several clock controller drivers define a list of clk_hw devices, and then
register those devices in probe() before using common code to process the
rest of initialization. Extend the common code to accept a list of clk_hw
devices to process, thus eliminating many duplicate implementations.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Suggested-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Tested-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
SPDX headers updated for common/branch/pll/regmap files.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Currently the driver assumes the register configuration value
is identical to its index in the parent map. This patch adds
the parent map field in regmap mux clock node which contains
the mapping of parent index with actual register configuration
value. If regmap node contains this parent map then the
configuration value will be taken from this
parent map instead of simply writing the index value.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The default behaviour with clk_rcg2_ops is for the
clk_round_rate()/clk_set_rate() to return/set a ceil clock
rate closest to the requested rate by looking up the corresponding
frequency table.
However, we do have some instances (mainly sdcc on various platforms)
of clients expecting a clk_set_rate() to set a floor value instead.
Add a new clk_rcg2_floor_ops to handle this for such specific
rcg instances
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The votable alpha PLLs need to have the fsm mode enabled as part
of the initialization. The sequence seems to be the same as used
by clk-pll, so move the function which does this into a common
place and reuse it for the clk-alpha-pll
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
We want to put the XO board clocks into the dt files, but we also
need to be backwards compatible with an older dtb. Add an API to
the common code to do this. This also makes a place for us to
handle the case when the RPM clock driver is enabled and we don't
want to register the fixed factor clock.
Cc: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Now that qcom_cc_remove() is a nop, drop calls to
qcom_cc_remove() and any empty driver remove functions.
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The common clk probe registers a clk provider and a reset controller.
Update it to register a genpd provider using the gdsc data provided
by each platform.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
In the current parent mapping code, we can get duplicate or inconsistent
indexes, which leads to discrepancy between the number of elements in the
array and the number of parents. Until now, this was solved with some
reordering but this is not always possible.
This patch introduces index tables that are used to define the relations
between the PLL source and the hardware mux configuration value.
To accomplish this, here we do the following:
- Define a parent_map struct to map the relations between PLL source index
and register configuration value.
- Add a qcom_find_src_index() function for finding the index of a clock
matching the specific PLL configuration.
- Update the {set,get}_parent RCG functions use the newly introduced
parent_map struct.
- Convert all existing drivers to the new parent_map tables.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
There are two find_freq() functions in clk-rcg.c and clk-rcg2.c
that are almost exactly the same. Consolidate them into one
function to save on some code space.
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Sometimes we need to program PLLs with a fixed rate
configuration during driver probe. Doing this after we register
the PLLs with the clock framework causes the common clock
framework to assume the rate of the PLLs are 0. This causes all
sorts of problems for rate recalculations because the common
clock framework caches the rate once at registration time unless
a flag is set to always recalculate the rates.
Split the qcom_cc_probe() function into two pieces, map and
everything else, so that drivers which need to configure some
PLL rates or otherwise twiddle bits in the clock controller can
do so before registering clocks. This allows us to properly
detect the rates of PLLs that are programmed at boot.
Fixes: 49fc825f0cc2 "clk: qcom: Consolidate common probe code"
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Most of the probe code is the same between all the different
clock controllers. Consolidate the code into a common.c file.
This makes changes to the common probe parts easier and reduces
chances for bugs.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
