If we have a HW restart in the middle of a ROC period,
then there are two cases:
- if it's a software ROC, we really don't need to do
anything, since the ROC work will still be queued
and will run later, albeit with the interruption
due to the restart;
- if it's a hardware ROC, then it may have begun or
not, if it did begin already we can only remove it
and tell userspace about that.
In both cases, this fixes the warning that would appear
in ieee80211_start_next_roc() in this case.
In the case of some drivers such as iwlwifi, the part of
restarting is never going to happen since the driver will
cancel the ROC, but flushing the work to ensure nothing
is pending here will also result in no longer being able
to trigger the warning in this case.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240523120352.f1924b5411ea.Ifc02a45a5ce23868dc7e428bad8d0e6996dd10f4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During non-STA management Tx, when source address is same as one of the
link addresses and even when userspace requested Tx on a specific link,
the link ID is not set in the TX control information. Now if the MLD
address is also the same as that of the link address, then mac80211
fills link as "unspecified", since it looks like MLD TX.
This is unexpected, however, since non-STA TX must specify which link
to use. In hwsim, this will (after warnings) result in dropping such
frames as well.
Use and set the link id if the link bss is matching the address and
requested channel.
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://msgid.link/20240410052705.169865-1-quic_adisi@quicinc.com
Link: https://lore.kernel.org/r/0496fb7e-53cc-476f-8052-985d82fd8d01@quicinc.com
[reword commit message, should spell out hwsim etc.]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are still surprisingly many non-chanctx drivers, but in
mac80211 that code is a bit awkward. Simplify this by having
those drivers assign 'emulated' ops, so that the mac80211 code
can be more unified between non-chanctx/chanctx drivers. This
cuts the number of places caring about it by about 15, which
are scattered across - now they're fewer and no longer in the
channel context handling.
Link: https://msgid.link/20240129194108.6d0ead50f5cf.I60d093b2fc81ca1853925a4d0ac3a2337d5baa5b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the remain on channel is removed at the time it should
have expired, we have a race: the driver could be handling
the flow of the expiration while mac80211 is cancelling
that very same remain on channel request.
This wouldn't be problem in itself, but since mac80211
can send the next request to the driver in the cancellation
flow, we can get to the following situation:
CPU0 CPU1
expiration of roc in driver
ieee80211_remain_on_channel_expired()
Cancellation of the roc
schedules a worker (hw_roc_done)
Add next roc
hw_roc_done_wk runs and ends
the second roc prematurely.
Since, by design, there is only one single request sent to the
driver at a time, we can safely assume that after the cancel()
request returns from the driver, we should not handle any worker
that handles the expiration of the request.
Cancel the hw_roc_done worker after the cancellation to make
sure we start the next one with a clean slate.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230928172905.4e4469be20ac.Iab0525f5cc4698acf23eab98b8b1eec02099cde0@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When user space transmits a management frame it is expected to use
the MLD addresses if the connection is an MLD one. Thus, in case
the management Tx is using the MLD address and no channel is configured
off-channel should not be used (as one of the active links would be used).
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230827135854.73c8efce252f.Ie4b0a842debb24ef25c5e6cb2ad69b9f46bc4b2a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since we're now protecting everything with the wiphy mutex
(and were really using it for almost everything before),
there's no longer any real reason to have a separate wdev
mutex. It may feel better, but really has no value.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We now hold the wiphy mutex everywhere that we use or
needed the iflist_mtx, so we don't need this mutex any
more in mac80211. However, drivers may also iterate,
and in some cases (e.g. mt76) do so from high-priority
contexts. Thus, keep the mutex around but remove its
usage in mac80211 apart from those driver-visible parts
that are still needed.
Most of this change was done automatically with spatch,
with the parts that are still needed as described above
reverted manually.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We now hold the wiphy mutex everywhere that we use or
needed the local->mtx, so we don't need this mutex any
more. Remove it.
Most of this change was done automatically with spatch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Along with everything else, move the dynamic PS work
to be a wiphy work, to simplify locking later.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In suspend flow "sdata" is NULL, destroy all roc's which are started.
pass "roc->sdata" to drv_cancel_remain_on_channel() to avoid NULL
dereference and destroy that roc
Signed-off-by: Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230608163202.c678187a308c.Ic11578778655e273931efc5355d570a16465d1be@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a couple of new things that should be possible
with MLO:
* selecting the link to transmit to a station by link ID,
which a previous patch added to the nl80211 API
* selecting the link by frequency, similarly
* allowing transmittion to an MLD without specifying any
channel or link ID, with MLD addresses
Enable these use cases. Also fix the address comparison
in client mode to use the AP (MLD) address.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since links can be added and removed dynamically, we need to
somehow protect the sdata->link[] and vif->link_conf[] array
pointers from disappearing when accessing them without locks.
RCU-ify the pointers to achieve this, which requires quite a
bit of rework.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Check all the MLO links to decide whether offchannel TX is needed.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Split the bss_info_changed method to vif_cfg_changed and
link_info_changed, with the latter getting a link ID.
Also change the 'changed' parameter to u64 already, we
know we need that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Start reorganizing interface related data structures toward
MLD. The most complex part here is for the keys, since we
have to split the various kinds of GTKs off to the link but
still need to use (for WEP) the other keys as a fallback
even for multicast frames.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We'll use bss_conf for per-link configuration later, so
move out all the non-link-specific data out into a new
struct ieee80211_vif_cfg used in the vif.
Some adjustments were done with the following spatch:
@@
expression sdata;
struct ieee80211_vif *vifp;
identifier var = { assoc, ibss_joined, aid, arp_addr_list, arp_addr_cnt, ssid, ssid_len, s1g, ibss_creator };
@@
(
-sdata->vif.bss_conf.var
+sdata->vif.cfg.var
|
-vifp->bss_conf.var
+vifp->cfg.var
)
@bss_conf@
struct ieee80211_bss_conf *bss_conf;
identifier var = { assoc, ibss_joined, aid, arp_addr_list, arp_addr_cnt, ssid, ssid_len, s1g, ibss_creator };
@@
-bss_conf->var
+vif_cfg->var
(though more manual fixups were needed, e.g. replacing
"vif_cfg->" by "vif->cfg." in many files.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To add MLD, reuse the bss_conf structure later for per-link
information, so move some things into it that are per link.
Most transformations were done with the following spatch:
@@
expression sdata;
identifier var = { chanctx_conf, mu_mimo_owner, csa_active, color_change_active, color_change_color };
@@
-sdata->vif.var
+sdata->vif.bss_conf.var
@@
struct ieee80211_vif *vif;
identifier var = { chanctx_conf, mu_mimo_owner, csa_active, color_change_active, color_change_color };
@@
-vif->var
+vif->bss_conf.var
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since we always track the BSSID there when we get associated,
these are equivalent, but ifmgd->bssid saves a dereference and
thus makes the code a bit smaller, and more readable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Because we can miss AP wakeup (beacon) while scanning other channels,
it's better go into wakeup state and inform the AP of that upon
returning to the operating channel, rather than staying asleep and
waiting for the next TIM indicating traffic for us.
This saves precious time, especially when we only have 200ms inter-
scan period for monitoring the active connection.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Link: https://lore.kernel.org/r/1593420923-26668-1-git-send-email-loic.poulain@linaro.org
[rewrite commit message a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We want to reuse the functions and structs for other counters such as BSS
color change. Rename them to more generic names.
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20200811080107.3615705-2-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211_chan_def and ieee80211_channel recently gained a
frequency offset component. Handle this where it makes
sense (potentially required by S1G channels).
For IBSS, TDLS, CSA, and ROC we return -EOPNOTSUPP if a
channel with frequency offset is passed, since they may or
may not work. Once someone tests and verifies these
commands work on thos types of channels, we can remove
that error.
join_ocb and join_mesh look harmless because they use a
simple ieee80211_vif_use_channel(), which is using an
already verified channel, so we let those through.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200402011810.22947-4-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This low level driver can find it useful to get the vif
when a remain on channel session is cancelled.
iwlwifi will need this soon.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://lore.kernel.org/r/20190723180001.5828-1-emmanuel.grumbach@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the offchannel TX wait time expires, send the appropriate event.
Signed-off-by: James Prestwood <james.prestwood@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Support the new random SN and minimal probe request contents
scan flags for the case of software scan - for hardware scan
the drivers need to opt in, but may need to do only that,
depending on their implementation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in some cases I replaced "fall through on else" and
"otherwise fall through" comments with just a "fall through" comment,
which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When HW ROC is supported it is possible that after the HW notified
that the ROC has started, the ROC was cancelled and another ROC was
added while the hw_roc_start worker is waiting on the mutex (since
cancelling the ROC and adding another one also holds the same mutex).
As a result, the hw_roc_start worker will continue to run after the
new ROC is added but before it is actually started by the HW.
This may result in notifying userspace that the ROC has started before
it actually does, or in case of management tx ROC, in an attempt to
tx while not on the right channel.
In addition, when the driver will notify mac80211 that the second ROC
has started, mac80211 will warn that this ROC has already been
notified.
Fix this by flushing the hw_roc_start work before cancelling an ROC.
Cc: stable@vger.kernel.org
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A common pattern with skb_put() is to just want to memcpy()
some data into the new space, introduce skb_put_data() for
this.
An spatch similar to the one for skb_put_zero() converts many
of the places using it:
@@
identifier p, p2;
expression len, skb, data;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_data(skb, data, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_data(skb, data, len);
)
(
p2 = (t2)p;
-memcpy(p2, data, len);
|
-memcpy(p, data, len);
)
@@
type t, t2;
identifier p, p2;
expression skb, data;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
)
(
p2 = (t2)p;
-memcpy(p2, data, sizeof(*p));
|
-memcpy(p, data, sizeof(*p));
)
@@
expression skb, len, data;
@@
-memcpy(skb_put(skb, len), data, len);
+skb_put_data(skb, data, len);
(again, manually post-processed to retain some comments)
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using IEEE 802.11r FT OVER-DS roaming with AP_VLAN, hostapd needs to
send out a frame using CMD_FRAME for a station assigned to an AP_VLAN
interface.
Right now, the userspace needs to give the exact AP_VLAN interface index
for CMD_FRAME; hostapd does not do this. Additionally, userspace cannot
use GET_STATION to query the AP_VLAN ifidx, as while GET_STATION finds
stations assigned to AP_VLAN even if the AP iface is queried, it does not
return AP_VLAN ifidx (it returns the queried one).
This breaks IEEE 802.11r over_ds with vlans, as the reply frame does not
get out. This patch fixes this by using get_sta_bss for CMD_FRAME.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This code doesn't do much besides allowing to start and
stop the vif.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows user space to start/stop NAN interface.
A NAN interface is like P2P device in a few aspects: it
doesn't have a netdev associated to it.
Add the new interface type and prevent operations that
can't be executed on NAN interface like scan.
Define several attributes that may be configured by user space
when starting NAN functionality (master preference and dual
band operation)
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Defer ROC requests during hw restart, as the driver
might not be fully configured in this stage (e.g.
channel contexts were not added yet)
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ilan's previous commit 1b894521e6 ("mac80211: handle HW
ROC expired properly") neglected to take into account that
hw_begun was now always set in the software implementation
as well as the offloaded case.
Fix hw_begun to only apply to the offloaded case to make
the check in Ilan's commit safe and correct.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current (new) code recalculates the new work timeout
for software remain-on-channel whenever any item started.
In two of the callers of ieee80211_handle_roc_started(),
this is completely pointless since they're for hardware
and will skip the recalculation entirely; it's necessary
only in the case of having just added a new item to the
list, as in the last remaining case the recalculation had
just been done.
This last case, however, is also problematic - if one of
the items on the list actually expires during the recalc
the list iteration outside becomes corrupted and crashes.
Fix this by moving the recalculation to the only place
where it's required.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case of HW ROC, when the driver reports that the ROC expired,
it is not sufficient to purge the ROCs based on the remaining
time, as it possible that the device finished the ROC session
before the actual requested duration.
To handle such cases, in case of ROC expired notification from
the driver, complete all the ROCs which are marked with hw_begun,
regardless of the remaining duration.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When cancelling, you can cancel "any" (first in list) mgmt-tx
or remain-on-channel operation by using the value 0 for the
cookie along with the *opposite* operation, i.e.
* cancel the first mgmt-tx by cancelling roc with 0 cookie
* cancel the first roc by cancelling mgmt-tx with 0 cookie
This isn't really that bad since userspace should only pass
cookies that we gave it, but could lead to hard-to-debug
issues so better prevent it and reject zero values since we
never hand those out.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Jouni found a bug in the remain-on-channel logic: when a short item
is queued, a long item is combined with it extending the original
one, and then the long item is deleted, the timeout doesn't go back
to the short one, and the short item ends up taking a long time. In
this case, this showed as blocking scan when running two test cases
back to back - the scan from the second was delayed even though all
the remain-on-channel items should long have been gone.
Fixing this with the current data structures turns out to be a bit
complicated, we just remove the long item from the dependents list
right now and don't recalculate the timeouts.
There's a somewhat similar bug where we delete the short item and
all the dependents go with it; to fix this we'd have to move them
from the dependents to the real list.
Instead of trying to do that, rewrite the code to not have all this
complexity in the data structures: use a single list and allow more
than one entry in it being marked as started. This makes the code a
bit more complex, the worker needs to understand that it might need
to just remove one of the started items, while keeping the device
off-channel, but that's not more complicated than the nested data
structures.
This then fixes both issues described, and makes it easier to also
limit the overall off-channel time when combining.
TODO: as before, with hardware remain-on-channel, deleting an item
after combining results in cancelling them all - we can keep track
of the time elapsed and only cancel after that to fix this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since the cookie is assigned inside ieee80211_make_ack_skb()
now, we no longer need to return the ack_skb as the cookie
and can simplify the function's return and the callers. Also
rename it to ieee80211_attach_ack_skb() to more accurately
reflect its purpose.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is quite a bit of code that logically depends here since
it has to deal with all the remain-on-channel logic.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a mgmt-tx operation is aborted before it runs, the wrong
cookie is reported back to userspace, and the ack_skb gets
leaked since the frame is freed directly instead of freeing
it using ieee80211_free_txskb(). Fix that.
Fixes: 3b79af973c ("mac80211: stop using pointers as userspace cookies")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of int with 0/1, use bool with false/true for the
powersave argument to ieee80211_send_nullfunc().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As we're running out of hardware capability flags pretty quickly,
convert them to use the regular test_bit() style unsigned long
bitmaps.
This introduces a number of helper functions/macros to set and to
test the bits, along with new debugfs code.
The occurrences of an explicit __clear_bit() are intentional, the
drivers were never supposed to change their supported bits on the
fly. We should investigate changing this to be a per-frame flag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When roaming / suspending, it makes no sense to wait until
the transmit queues of the device are empty. In extreme
condition they can be starved (VO saturating the air), but
even in regular cases, it is pointless to delay the roaming
because the low level driver is trying to send packets to
an AP which is far away. We'd rather drop these packets and
let TCP retransmit if needed. This will allow to speed up
the roaming.
For suspend, the explanation is even more trivial.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sometimes different vifs may be stopping the queues for the same
reason (e.g. when several interfaces are performing a channel switch).
Instead of using a bitmask for the reasons, use an integer that holds
a refcount instead. In order to keep it backwards compatible,
introduce a boolean in some functions that tell us whether the queue
stopping should be refcounted or not. For now, use not refcounted for
all calls to keep it functionally the same as before.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Jouni reported that if a remain-on-channel was active on the
same channel as the current operating channel, then the ROC
would start, but any frames transmitted using mgmt-tx on the
same channel would get delayed until after the ROC.
The reason for this is that the ROC starts, but doesn't have
any handling for "remain on the same channel", so it stops
the interface queues. The later mgmt-tx then puts the frame
on the interface queues (since it's on the current operating
channel) and thus they get delayed until after the ROC.
To fix this, add some logic to handle remaining on the same
channel specially and not stop the queues etc. in this case.
This not only fixes the bug but also improves behaviour in
this case as data frames etc. can continue to flow.
Cc: stable@vger.kernel.org
Reported-by: Jouni Malinen <j@w1.fi>
Tested-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
