* controller/rockchip:
PCI: rockchip: Add missing fields descriptions for struct rockchip_pcie_ep
PCI: dw-rockchip: Enumerate endpoints based on dll_link_up irq in the combined sys irq
* controller/mediatek:
PCI: mediatek-gen3: Avoid PCIe resetting via PCIE_RSTB for Airoha EN7581 SoC
PCI: mediatek-gen3: Use msleep() in mtk_pcie_en7581_power_up()
PCI: mediatek-gen3: Add reset delay in mtk_pcie_en7581_power_up()
PCI: mediatek-gen3: Add comment about initialization order in mtk_pcie_en7581_power_up()
PCI: mediatek-gen3: Move reset/assert callbacks in .power_up()
PCI: mediatek-gen3: Use clk_bulk_prepare_enable() in mtk_pcie_en7581_power_up()
PCI: mediatek-gen3: Add missing reset_control_deassert() for mac_rst in mtk_pcie_en7581_power_up()
* endpoint:
misc: pci_endpoint_test: Add support for capabilities
PCI: endpoint: pci-epf-test: Add support for capabilities
PCI: endpoint: Verify that requested BAR size is a power of two
PCI: endpoint: Add size check for fixed size BARs in pci_epc_set_bar()
PCI: artpec6: Implement dw_pcie_ep operation get_features
PCI: dwc: ep: Add 'address' alignment to 'size' check in dw_pcie_prog_ep_inbound_atu()
PCI: dwc: ep: Prevent changing BAR size/flags in pci_epc_set_bar()
PCI: dwc: ep: Write BAR_MASK before iATU registers in pci_epc_set_bar()
PCI: endpoint: Finish virtual EP removal in pci_epf_remove_vepf()
PCI: endpoint: Simplify pci_epc_get()
PCI: endpoint: Destroy the EPC device in devm_pci_epc_destroy()
PCI: endpoint: Replace magic number '6' by PCI_STD_NUM_BARS
* devres:
HID: amd_sfh: Use always-managed version of pcim_intx()
wifi: qtnfmac: use always-managed version of pcim_intx()
ata: Use always-managed version of pci_intx()
PCI/MSI: Use never-managed version of pci_intx()
vfio/pci: Use never-managed version of pci_intx()
misc: Use never-managed version of pci_intx()
ntb: Use never-managed version of pci_intx()
drivers/xen: Use never-managed version of pci_intx()
PCI: Export pci_intx_unmanaged() and pcim_intx()
An rsb struct was not being removed in the case where it
was both the master and the dir record. This case (master
and dir node) was missed in the condition for doing add_scan()
from deactivate_rsb(). Fixing this triggers a related WARN_ON
that needs to be fixed, and requires adjusting where two
del_scan() calls are made.
Fixes: c217adfc8c ("dlm: fix add_scan and del_scan usage")
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
The header clearly states that it does not want to be included directly,
only via 'device.h'. The 'platform_device.h' works equally well.
Thus, remove the direct inclusion.
Link: https://lore.kernel.org/r/20241118072917.3853-12-wsa+renesas@sang-engineering.com
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Airoha EN7581 has a hardware bug asserting/releasing PCIE_PE_RSTB signal
causing occasional PCIe link down issues. In order to overcome the
problem, PCIE_RSTB signals are not asserted/released during device probe
or suspend/resume phase and the PCIe block is reset using REG_PCI_CONTROL
(0x88) and REG_RESET_CONTROL (0x834) registers available in the clock
module running clk_bulk_prepare_enable in mtk_pcie_en7581_power_up().
Introduce flags field in the mtk_gen3_pcie_pdata struct in order to
specify per-SoC capabilities.
Link: https://lore.kernel.org/r/20241113-pcie-en7581-rst-fix-v3-1-23c5082335f7@kernel.org
Tested-by: Hui Ma <hui.ma@airoha.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Cc: stable@vger.kernel.org
This reverts commit f042bc234c.
A recent change enabling role switching for the x1e80100 USB-C
controllers breaks UCSI and DisplayPort Alternate Mode when the
controllers are in host mode:
ucsi_glink.pmic_glink_ucsi pmic_glink.ucsi.0: PPM init failed, stop trying
As enabling OTG mode currently breaks SuperSpeed hotplug and suspend,
and with retimer (and orientation detection) support not even merged
yet, let's revert at least until we have stable host mode in mainline.
Fixes: f042bc234c ("arm64: dts: qcom: x1e80100: enable OTG on USB-C controllers")
Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/all/hw2pdof4ajadjsjrb44f2q4cz4yh5qcqz5d3l7gjt2koycqs3k@xx5xvd26uyef
Link: https://lore.kernel.org/lkml/Z1gbyXk-SktGjL6-@hovoldconsulting.com/
Cc: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20241210111444.26240-4-johan+linaro@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
This reverts commit 2dd3250191.
A recent change enabling OTG mode on the x1e81000 CRD breaks suspend.
Specifically, the device hard resets during resume if suspended with all
controllers in device mode (i.e. no USB device connected).
The corresponding change on the T14s also led to SuperSpeed hotplugs not
being detected.
With retimer (and orientation detection) support not even merged yet,
let's revert at least until we have stable host mode in mainline.
Fixes: 2dd3250191 ("arm64: dts: qcom: x1e80100-crd: enable otg on usb ports")
Reported-by: Abel Vesa <abel.vesa@linaro.org>
Cc: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20241210111444.26240-3-johan+linaro@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Since mtk_pcie_en7581_power_up() runs in non-atomic context, rely on
msleep() routine instead of mdelay().
Link: https://lore.kernel.org/r/20241130-pcie-en7581-fixes-v5-6-dbffe41566b3@kernel.org
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Airoha EN7581 has a hw bug asserting/releasing PCIE_PE_RSTB signal
causing occasional PCIe link down issues. In order to overcome the
problem, PCIe block is reset using REG_PCI_CONTROL (0x88) and
REG_RESET_CONTROL (0x834) registers available in the clock module
running clk_bulk_prepare_enable in mtk_pcie_en7581_power_up().
In order to make the code more readable, move the wait for the time
needed to complete the PCIe reset from en7581_pci_enable() to
mtk_pcie_en7581_power_up().
Reduce reset timeout from 250ms to the standard PCIE_T_PVPERL_MS value
(100ms) since it has no impact on the driver behavior.
Link: https://lore.kernel.org/r/20241130-pcie-en7581-fixes-v5-5-dbffe41566b3@kernel.org
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Add a comment in mtk_pcie_en7581_power_up() to clarify, unlike the other
MediaTek Gen3 controllers, the Airoha EN7581 requires PHY initialization
and power-on before PHY reset deassert.
Link: https://lore.kernel.org/r/20241130-pcie-en7581-fixes-v5-4-dbffe41566b3@kernel.org
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
In order to make the code more readable, the reset_control_bulk_assert()
for PHY reset lines is moved to make it pair with
reset_control_bulk_deassert() in mtk_pcie_power_up() and
mtk_pcie_en7581_power_up(). The same change is done for
reset_control_assert() used to assert MAC reset line.
Introduce PCIE_MTK_RESET_TIME_US macro for the time needed to
complete PCIe reset on MediaTek controller.
Link: https://lore.kernel.org/r/20241130-pcie-en7581-fixes-v5-3-dbffe41566b3@kernel.org
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Replace clk_bulk_prepare() and clk_bulk_enable() with
clk_bulk_prepare_enable() in mtk_pcie_en7581_power_up() routine.
Link: https://lore.kernel.org/r/20241130-pcie-en7581-fixes-v5-2-dbffe41566b3@kernel.org
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Even if this is not a real issue since Airoha EN7581 SoC does not require
the mac reset line, add missing reset_control_deassert() for mac reset
line in mtk_pcie_en7581_power_up() callback.
Link: https://lore.kernel.org/r/20241130-pcie-en7581-fixes-v5-1-dbffe41566b3@kernel.org
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
When compiling the Rockchip endpoint driver with -W=1, the following
warnings can be seen in the output:
drivers/pci/controller/pcie-rockchip-ep.c:59: warning: Function parameter or struct member 'perst_irq' not described in 'rockchip_pcie_ep'
drivers/pci/controller/pcie-rockchip-ep.c:59: warning: Function parameter or struct member 'perst_asserted' not described in 'rockchip_pcie_ep'
drivers/pci/controller/pcie-rockchip-ep.c:59: warning: Function parameter or struct member 'link_up' not described in 'rockchip_pcie_ep'
drivers/pci/controller/pcie-rockchip-ep.c:59: warning: Function parameter or struct member 'link_training' not described in 'rockchip_pcie_ep'
Fix these warnings by adding the missing field descriptions in
struct rockchip_pcie_ep kernel-doc comment.
Fixes: a7137cbf6b ("PCI: rockchip-ep: Handle PERST# signal in EP mode")
Fixes: bd6e61df4b ("PCI: rockchip-ep: Improve link training")
Link: https://lore.kernel.org/r/20241216133404.540736-1-dlemoal@kernel.org
Reported-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Previously, deferred file handles were reused only for read
operations, this commit extends to reusing deferred handles
for write operations.
Signed-off-by: Bharath SM <bharathsm@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
With recent netfs apis changes, the bytes written
value was not getting updated in /proc/fs/cifs/Stats.
Fix this by updating tcon->bytes in write operations.
Fixes: 3ee1a1fc39 ("cifs: Cut over to using netfslib")
Signed-off-by: Bharath SM <bharathsm@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
There is no such thing as CPACR_ELx in the architecture.
What we have is CPACR_EL1, for which CPTR_EL12 is an accessor.
Rename CPACR_ELx_* to CPACR_EL1_*, and fix the bit of code using
these names.
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20241219173351.1123087-5-maz@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Perform a bulk convert of the remaining EL12 accessors to use the
Mapping qualifier, which makes things a bit clearer.
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20241219173351.1123087-4-maz@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
TCR2_EL1x is a pretty bizarre construct, as it is shared between
TCR2_EL1 and TCR2_EL12. But the latter is obviously only an
accessor to the former.
In order to make things more consistent, upgrade TCR2_EL1x to
a full-blown sysreg definition for TCR2_EL1, and describe TCR2_EL12
as a mapping to TCR2_EL1.
This results in a couple of minor changes to the actual code.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20241219173351.1123087-3-maz@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
*EL02 and *_EL12 system registers are actually only accessors for
EL0 and EL1 registers accessed from EL2 when HCR_EL2.E2H==1. They
do not have fields of their own.
To that effect, introduce a 'Mapping' entry, describing which
system register an _EL12 register maps to.
Implementation wise, this is handled the same was as Fields,
which ls only a comment.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20241219173351.1123087-2-maz@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
There is a spelling mistake in an ath12k_err error message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241217105505.306047-1-colin.i.king@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, monitor status parse procedure handles all the supported TLV
tags. Each TLV tag has its own data structure for parsing. Now, this
handler is passed the tlv_data as a u8 pointer, so explicit type cast
conversion happens for every TLV tag parsing. Therefore, avoid the
explicit type conversion by changing the tlv_data type from a u8 pointer
to a const void pointer.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241217084511.2981515-9-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The Tx monitor SRNG ring ID does not align with the ath12k 802.11be
hardware architecture. Currently, there is no issue since the Tx monitor
is not enabled. However, in the future, the Tx monitor will be enabled.
Therefore, change the HAL_SRNG_RING_ID_WMAC1_SW2TXMON_BUF0 SRNG ID and
assign the correct start ring ID for the ring type HAL_TX_MONITOR_BUF.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241217084511.2981515-8-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, CODING and TXBF are unused masks defined in the HAL Rx monitor
status TLV parsing code path. Therefore, remove the unused masks to
prevent incorrect assumptions for code readers.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241217084511.2981515-7-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, an incorrect TID value gets populated in the monitor status Rx
path due to an incorrect bitmap value given to the ffs() built-in helper
function. Therefore, avoid the decrement and directly provide the TID
bitmap to the ffs() built-in helper function for the correct TID update
in the monitor status Rx path.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241217084511.2981515-6-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
There is "HAL_PHYRX_GENERICHT_SIG" misspelled as
"HAL_PHYRX_GENERIC_EHT_SIG" in the comments. Fix the spelling.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241217084511.2981515-5-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, unused fields are present in the Rx peer statistics
structure. These fields are already present in the same structure
under the ath12k_rx_peer_rate_stats container structure. Therefore,
remove the unused fields from the Rx peer statistics structure.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241217084511.2981515-4-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The following TLV structures and bitmask definitions were inherited from
the ath11k but were not updated for the ath12k 802.11be hardware. These
data structure and bitmask will be used to parse the monitor status
TLV data in the Rx path.
1. hal_rx_ppdu_end_user_stats_ext structure
2. hal_rx_ppdu_end_duration structure
3. HAL_RX_HE_SIG_B2_OFDMA_INFO_INFO0_STA_TXBF bitmask
4. HAL_RX_MPDU_START_INFO1_PEERID bitmask
5. HAL_INVALID_PEERID
6. hal_rx_ppdu_end_user_stats bitmask
Currently, there is no issue since the monitor status Rx path is not
enabled. However, in the future, the monitor status Rx path will be
enabled. Therefore, update the above TLV structures and bitmask to align
with the ath12k 802.11be hardware.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241217084511.2981515-3-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Add missing field documentation for HTT_H2T_MSG_TYPE_RX_RING_SELECTION_CFG
command with indentation alignment.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241217084511.2981515-2-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Building the ath12k driver with llvm-18.1.7-x86_64 produces the warning:
drivers/net/wireless/ath/ath12k/mac.c:5606:12: warning: stack frame size (1176) exceeds limit (1024) in 'ath12k_mac_op_sta_state' [-Wframe-larger-than]
ath12k_mac_op_sta_state() itself does not consume much stack, but it
calls ath12k_mac_handle_link_sta_state() which in turn calls
ath12k_mac_station_add(). Since those are both static functions with
only one caller, it is suspected that these both get inlined, and
their stack usage is reported for ath12k_mac_op_sta_state().
A major contributor to the ath12k_mac_station_assoc() stack usage is:
struct ath12k_wmi_peer_assoc_arg peer_arg;
Avoid the excess stack usage by dynamically allocating peer_arg
instead of declaring it on the stack.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241217202618.1329312-5-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently when building ath12k with llvm-18.1.7-x86_64 the following warning is
observed:
drivers/net/wireless/ath/ath12k/mac.c:4946:13: warning: stack frame size (1112) exceeds limit (1024) in 'ath12k_sta_rc_update_wk' [-Wframe-larger-than]
A major contributor to the stack usage in this function is:
struct ath12k_wmi_peer_assoc_arg peer_arg;
Avoid the excess stack usage by dynamically allocating peer_arg
instead of declaring it on the stack.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241217202618.1329312-4-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently when building ath12k with gcc-14.2.0 the following warning
is observed:
drivers/net/wireless/ath/ath12k/mac.c: In function 'ath12k_bss_assoc':
drivers/net/wireless/ath/ath12k/mac.c:3080:1: warning: the frame size of 1040 bytes is larger than 1024 bytes [-Wframe-larger-than=]
A major contributor to the stack usage in this function is:
struct ath12k_wmi_peer_assoc_arg peer_arg;
Avoid the excess stack usage by dynamically allocating peer_arg
instead of declaring it on the stack.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241217202618.1329312-3-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Building the ath12k driver with llvm-18.1.7-x86_64 produces the warning:
drivers/net/wireless/ath/ath12k/mac.c:10028:12: warning: stack frame size (1080) exceeds limit (1024) in 'ath12k_mac_op_remain_on_channel' [-Wframe-larger-than]
A major contributor to the stack usage in this function is:
struct ath12k_wmi_scan_req_arg arg;
Avoid the excess stack usage by dynamically allocating arg instead of
declaring it on the stack. As part of the effort use __free() for both
this new allocation as well as the existing chan_list allocation, and
since then no central cleanup is required, replace all cleanup gotos
with returns.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241217202618.1329312-2-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
There is mismatch between the format of monitor destination TLVs received
and the expected format by the current implementation. The received TLVs
are in 64-bit format, while the implementation is designed to handle
32-bit TLVs. This leads to incorrect parsing. Fix it by adding support
for parsing 64-bit TLVs.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Acked-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Link: https://patch.msgid.link/20241217095058.2725755-1-quic_ppranees@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Prefer 'ktime_t' over 'struct timespec64' for 'struct ath_chanctx' and
'struct ath_softc' timestamps, choose standard kernel time API over an
ad-hoc math in 'chanctx_event_delta()' and 'ath9k_hw_get_tsf_offset()',
adjust related users. Compile tested only.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://patch.msgid.link/20241209155027.636400-3-dmantipov@yandex.ru
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Since 'txq' argument of 'ath_txq_skb_done()' is actually
(mis|un)used, convert the former to local variable and
adjust all related users. Compile tested only.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://patch.msgid.link/20241209155027.636400-1-dmantipov@yandex.ru
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the maximum supported physical address space can be
configured as either 48 bits or 52 bits. The only remaining difference
between these in practice is that the former omits the masking and
shifting required to construct TTBR and PTE values, which carry bits #48
and higher disjoint from the rest of the physical address.
The overhead of performing these additional calculations is negligible,
and so there is little reason to retain support for two different
configurations, and we can simply support whatever the hardware
supports.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20241212081841.2168124-14-ardb+git@google.com
Signed-off-by: Will Deacon <will@kernel.org>
There are a couple of instances of Kconfig constraints where PAN must be
enabled too if TTBR0 sw PAN is enabled, primarily to avoid dealing with
the modified TTBR0_EL1 sysreg format that is used when 52-bit physical
addressing and/or CnP are enabled (support for either implies support
for hardware PAN as well, which will supersede PAN emulation if both are
available)
Let's simplify this, and always enable ARM64_PAN when enabling TTBR0 sw
PAN. This decouples the PAN configuration from the VA size selection,
permitting us to simplify the latter in subsequent patches. (Note that
PAN and TTBR0 sw PAN can still be disabled after this patch, but not
independently)
To avoid a convoluted circular Kconfig dependency involving KCSAN, make
ARM64_MTE select ARM64_PAN too, instead of depending on it.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20241212081841.2168124-13-ardb+git@google.com
Signed-off-by: Will Deacon <will@kernel.org>
The pKVM stage2 mapping code relies on an invalid physical address to
signal to the internal API that only the annotations of descriptors
should be updated, and these are stored in the high bits of invalid
descriptors covering memory that has been donated to protected guests,
and is therefore unmapped from the host stage-2 page tables.
Given that these invalid PAs are never stored into the descriptors, it
is better to rely on an explicit flag, to clarify the API and to avoid
confusion regarding whether or not the output address of a descriptor
can ever be invalid to begin with (which is not the case with LPA2).
That removes a dependency on the logic that reasons about the maximum PA
range, which differs on LPA2 capable CPUs based on whether LPA2 is
enabled or not, and will be further clarified in subsequent patches.
Cc: Quentin Perret <qperret@google.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Quentin Perret <qperret@google.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20241212081841.2168124-12-ardb+git@google.com
Signed-off-by: Will Deacon <will@kernel.org>
When the host stage1 is configured for LPA2, the value currently being
programmed into TCR_EL2.T0SZ may be invalid unless LPA2 is configured
at HYP as well. This means kvm_lpa2_is_enabled() is not the right
condition to test when setting TCR_EL2.DS, as it will return false if
LPA2 is only available for stage 1 but not for stage 2.
Similary, programming TCR_EL2.PS based on a limited IPA range due to
lack of stage2 LPA2 support could potentially result in problems.
So use lpa2_is_enabled() instead, and set the PS field according to the
host's IPS, which is capped at 48 bits if LPA2 support is absent or
disabled. Whether or not we can make meaningful use of such a
configuration is a different question.
Cc: stable@vger.kernel.org
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20241212081841.2168124-11-ardb+git@google.com
Signed-off-by: Will Deacon <will@kernel.org>
