Here are two small serial driver fixes for 6.13-rc3. They are:
- ioport build fallout fix for the 8250 port driver that should
resolve Guenter's runtime problems
- sh-sci driver bugfix for a reported problem
Both of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZ12XXg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymGXACfezq1bc3UAJeZqZcDhAQrhZKiLHsAoMx76hi1
Ol6uRsbGrVi5bITDnuhl
=wF8l
-----END PGP SIGNATURE-----
Merge tag 'tty-6.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull serial driver fixes from Greg KH:
"Here are two small serial driver fixes for 6.13-rc3. They are:
- ioport build fallout fix for the 8250 port driver that should
resolve Guenter's runtime problems
- sh-sci driver bugfix for a reported problem
Both of these have been in linux-next for a while with no reported
issues"
* tag 'tty-6.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: serial: Work around warning backtrace in serial8250_set_defaults
serial: sh-sci: Check if TX data was written to device in .tx_empty()
Commit 7c7e6c8924 ("tty: serial: handle HAS_IOPORT dependencies")
triggers warning backtraces on a number of platforms which don't support
IO ports.
WARNING: CPU: 0 PID: 0 at drivers/tty/serial/8250/8250_port.c:470 serial8250_set_defaults+0x148/0x1d8
Unsupported UART type 0
The problem is seen because serial8250_set_defaults() is called for
all members of the serial8250_ports[] array even if that array is
not initialized.
Work around the problem by only displaying the warning if the port
type is not 0 (UPIO_PORT) or if iobase is set for the port.
Fixes: 7c7e6c8924 ("tty: serial: handle HAS_IOPORT dependencies")
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Stafford Horne <shorne@gmail.com>
Link: https://lore.kernel.org/r/20241205143033.2695333-1-linux@roeck-us.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On the Renesas RZ/G3S, when doing suspend to RAM, the uart_suspend_port()
is called. The uart_suspend_port() calls 3 times the
struct uart_port::ops::tx_empty() before shutting down the port.
According to the documentation, the struct uart_port::ops::tx_empty()
API tests whether the transmitter FIFO and shifter for the port is
empty.
The Renesas RZ/G3S SCIFA IP reports the number of data units stored in the
transmit FIFO through the FDR (FIFO Data Count Register). The data units
in the FIFOs are written in the shift register and transmitted from there.
The TEND bit in the Serial Status Register reports if the data was
transmitted from the shift register.
In the previous code, in the tx_empty() API implemented by the sh-sci
driver, it is considered that the TX is empty if the hardware reports the
TEND bit set and the number of data units in the FIFO is zero.
According to the HW manual, the TEND bit has the following meaning:
0: Transmission is in the waiting state or in progress.
1: Transmission is completed.
It has been noticed that when opening the serial device w/o using it and
then switch to a power saving mode, the tx_empty() call in the
uart_port_suspend() function fails, leading to the "Unable to drain
transmitter" message being printed on the console. This is because the
TEND=0 if nothing has been transmitted and the FIFOs are empty. As the
TEND=0 has double meaning (waiting state, in progress) we can't
determined the scenario described above.
Add a software workaround for this. This sets a variable if any data has
been sent on the serial console (when using PIO) or if the DMA callback has
been called (meaning something has been transmitted). In the tx_empty()
API the status of the DMA transaction is also checked and if it is
completed or in progress the code falls back in checking the hardware
registers instead of relying on the software variable.
Fixes: 73a19e4c03 ("serial: sh-sci: Add DMA support.")
Cc: stable@vger.kernel.org
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20241125115856.513642-1-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit cdd30ebb1b ("module: Convert symbol namespace to string
literal") only converted MODULE_IMPORT_NS() and EXPORT_SYMBOL_NS(),
leaving DEFAULT_SYMBOL_NAMESPACE as a macro expansion.
This commit converts DEFAULT_SYMBOL_NAMESPACE in the same way to avoid
annoyance for the default namespace as well.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The continual trickle of small conversion patches is grating on me, and
is really not helping. Just get rid of the 'remove_new' member
function, which is just an alias for the plain 'remove', and had a
comment to that effect:
/*
* .remove_new() is a relic from a prototype conversion of .remove().
* New drivers are supposed to implement .remove(). Once all drivers are
* converted to not use .remove_new any more, it will be dropped.
*/
This was just a tree-wide 'sed' script that replaced '.remove_new' with
'.remove', with some care taken to turn a subsequent tab into two tabs
to make things line up.
I did do some minimal manual whitespace adjustment for places that used
spaces to line things up.
Then I just removed the old (sic) .remove_new member function, and this
is the end result. No more unnecessary conversion noise.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here is a small set of tty and serial driver updates for 6.13-rc1.
Nothing major at all this time, only some small changes:
- few device tree binding updates
- 8250_exar serial driver updates
- imx serial driver updates
- sprd_serial driver updates
- other tiny serial driver updates, full details in the shortlog
All of these have been in linux-next for a while with one reported
issue, but that commit has now been reverted.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZ0s3DA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykmgQCeIDU0GHWFuzEiZNmsO5bLN8AcoFQAn1rlOaHu
9lOOf7xVSCUBU0GgynI5
=SEtJ
-----END PGP SIGNATURE-----
Merge tag 'tty-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is a small set of tty and serial driver updates for 6.13-rc1.
Nothing major at all this time, only some small changes:
- few device tree binding updates
- 8250_exar serial driver updates
- imx serial driver updates
- sprd_serial driver updates
- other tiny serial driver updates, full details in the shortlog
All of these have been in linux-next for a while with one reported
issue, but that commit has now been reverted"
* tag 'tty-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (37 commits)
Revert "serial: sh-sci: Clean sci_ports[0] after at earlycon exit"
serial: amba-pl011: fix build regression
dt-bindings: serial: Add a new compatible string for ums9632
serial: sprd: Add support for sc9632
tty/serial/altera_uart: unwrap error log string
tty/serial/altera_jtaguart: unwrap error log string
serial: amba-pl011: Fix RX stall when DMA is used
tty: ldsic: fix tty_ldisc_autoload sysctl's proc_handler
serial: 8250_fintek: Add support for F81216E
serial: sh-sci: Clean sci_ports[0] after at earlycon exit
tty: atmel_serial: Fix typo retreives to retrieves
tty: atmel_serial: Use devm_platform_ioremap_resource()
serial: 8250: omap: Move pm_runtime_get_sync
tty: serial: samsung: Add Exynos8895 compatible
dt-bindings: serial: samsung: Add samsung,exynos8895-uart compatible
serial: 8250_dw: Add Sophgo SG2044 quirk
dt-bindings: serial: snps-dw-apb-uart: Add Sophgo SG2044 uarts
dt-bindings: serial: snps,dw-apb-uart: merge duplicate compatible entry.
altera_jtaguart: Use dev_err() to report error attaching IRQ
altera_uart: Use dev_err() to report error attaching IRQ handler
...
This reverts commit 3791ea69a4.
It was reported to cause boot-time issues, so revert it for now.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes: 3791ea69a4 ("serial: sh-sci: Clean sci_ports[0] after at earlycon exit")
Cc: stable <stable@kernel.org>
Cc: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----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=2Otz
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.13-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Make pci_stop_dev() and pci_destroy_dev() safe so concurrent
callers can't stop a device multiple times, even as we migrate from
the global pci_rescan_remove_lock to finer-grained locking (Keith
Busch)
- Improve pci_walk_bus() implementation by making it recursive and
moving locking up to avoid need for a 'locked' parameter (Keith
Busch)
- Unexport pci_walk_bus_locked(), which is only used internally by
the PCI core (Keith Busch)
- Detect some Thunderbolt chips that are built-in and hence
'trustworthy' by a heuristic since the 'ExternalFacingPort' and
'usb4-host-interface' ACPI properties are not quite enough (Esther
Shimanovich)
Resource management:
- Use PCI bus addresses (not CPU addresses) in 'ranges' properties
when building dynamic DT nodes so systems where PCI and CPU
addresses differ work correctly (Andrea della Porta)
- Tidy resource sizing and assignment with helpers to reduce
redundancy (Ilpo Järvinen)
- Improve pdev_sort_resources() 'bogus alignment' warning to be more
specific (Ilpo Järvinen)
Driver binding:
- Convert driver .remove_new() callbacks to .remove() again to finish
the conversion from returning 'int' to being 'void' (Sergio
Paracuellos)
- Export pcim_request_all_regions(), a managed interface to request
all BARs (Philipp Stanner)
- Replace pcim_iomap_regions_request_all() with
pcim_request_all_regions(), and pcim_iomap_table()[n] with
pcim_iomap(n), in the following drivers: ahci, crypto qat, crypto
octeontx2, intel_th, iwlwifi, ntb idt, serial rp2, ALSA korg1212
(Philipp Stanner)
- Remove the now unused pcim_iomap_regions_request_all() (Philipp
Stanner)
- Export pcim_iounmap_region(), a managed interface to unmap and
release a PCI BAR (Philipp Stanner)
- Replace pcim_iomap_regions(mask) with pcim_iomap_region(n), and
pcim_iounmap_regions(mask) with pcim_iounmap_region(n), in the
following drivers: fpga dfl-pci, block mtip32xx, gpio-merrifield,
cavium (Philipp Stanner)
Error handling:
- Add sysfs 'reset_subordinate' to reset the entire hierarchy below a
bridge; previously Secondary Bus Reset could only be used when
there was a single device below a bridge (Keith Busch)
- Warn if we reset a running device where the driver didn't register
pci_error_handlers notification callbacks (Keith Busch)
ASPM:
- Disable ASPM L1 before touching L1 PM Substates to follow the spec
closer and avoid a CPU load timeout on some platforms (Ajay
Agarwal)
- Set devices below Intel VMD to D0 before enabling ASPM L1 Substates
as required per spec for all L1 Substates changes (Jian-Hong Pan)
Power management:
- Enable starfive controller runtime PM before probing host bridge
(Mayank Rana)
- Enable runtime power management for host bridges (Krishna chaitanya
chundru)
Power control:
- Use of_platform_device_create() instead of of_platform_populate()
to create pwrctl platform devices so we can control it based on the
child nodes (Manivannan Sadhasivam)
- Create pwrctrl platform devices only if there's a relevant power
supply property (Manivannan Sadhasivam)
- Add device link from the pwrctl supplier to the PCI dev to ensure
pwrctl drivers are probed before the PCI dev driver; this avoids a
race where pwrctl could change device power state while the PCI
driver was active (Manivannan Sadhasivam)
- Find pwrctl device for removal with of_find_device_by_node()
instead of searching all children of the parent (Manivannan
Sadhasivam)
- Rename 'pwrctl' to 'pwrctrl' to match new bandwidth controller
('bwctrl') and hotplug files (Bjorn Helgaas)
Bandwidth control:
- Add read/modify/write locking for Link Control 2, which is used to
manage Link speed (Ilpo Järvinen)
- Extract Link Bandwidth Management Status check into
pcie_lbms_seen(), where it can be shared between the bandwidth
controller and quirks that use it to help retrain failed links
(Ilpo Järvinen)
- Re-add Link Bandwidth notification support with updates to address
the reasons it was previously reverted (Alexandru Gagniuc, Ilpo
Järvinen)
- Add pcie_set_target_speed() and related functionality so drivers
can manage PCIe Link speed based on thermal or other constraints
(Ilpo Järvinen)
- Add a thermal cooling driver to throttle PCIe Links via the
existing thermal management framework (Ilpo Järvinen)
- Add a userspace selftest for the PCIe bandwidth controller (Ilpo
Järvinen)
PCI device hotplug:
- Add hotplug controller driver for Marvell OCTEON multi-function
device where function 0 has a management console interface to
enable/disable and provision various personalities for the other
functions (Shijith Thotton)
- Retain a reference to the pci_bus for the lifetime of a pci_slot to
avoid a use-after-free when the thunderbolt driver resets USB4 host
routers on boot, causing hotplug remove/add of downstream docks or
other devices (Lukas Wunner)
- Remove unused cpcihp struct cpci_hp_controller_ops.hardware_test
(Guilherme Giacomo Simoes)
- Remove unused cpqphp struct ctrl_dbg.ctrl (Christophe JAILLET)
- Use pci_bus_read_dev_vendor_id() instead of hand-coded presence
detection in cpqphp (Ilpo Järvinen)
- Simplify cpqphp enumeration, which is already simple-minded and
doesn't handle devices below hot-added bridges (Ilpo Järvinen)
Virtualization:
- Add ACS quirk for Wangxun FF5xxx NICs, which don't advertise an ACS
capability but do isolate functions as though PCI_ACS_RR and
PCI_ACS_CR were set, so the functions can be in independent IOMMU
groups (Mengyuan Lou)
TLP Processing Hints (TPH):
- Add and document TLP Processing Hints (TPH) support so drivers can
enable and disable TPH and the kernel can save/restore TPH
configuration (Wei Huang)
- Add TPH Steering Tag support so drivers can retrieve Steering Tag
values associated with specific CPUs via an ACPI _DSM to improve
performance by directing DMA writes closer to their consumers (Wei
Huang)
Data Object Exchange (DOE):
- Wait up to 1 second for DOE Busy bit to clear before writing a
request to the mailbox to avoid failures if the mailbox is still
busy from a previous transfer (Gregory Price)
Endpoint framework:
- Skip attempts to allocate from endpoint controller memory window if
the requested size is larger than the window (Damien Le Moal)
- Add and document pci_epc_mem_map() and pci_epc_mem_unmap() to
handle controller-specific size and alignment constraints, and add
test cases to the endpoint test driver (Damien Le Moal)
- Implement dwc pci_epc_ops.align_addr() so pci_epc_mem_map() can
observe DWC-specific alignment requirements (Damien Le Moal)
- Synchronously cancel command handler work in endpoint test before
cleaning up DMA and BARs (Damien Le Moal)
- Respect endpoint page size in dw_pcie_ep_align_addr() (Niklas
Cassel)
- Use dw_pcie_ep_align_addr() in dw_pcie_ep_raise_msi_irq() and
dw_pcie_ep_raise_msix_irq() instead of open coding the equivalent
(Niklas Cassel)
- Avoid NULL dereference if Modem Host Interface Endpoint lacks
'mmio' DT property (Zhongqiu Han)
- Release PCI domain ID of Endpoint controller parent (not controller
itself) and before unregistering the controller, to avoid
use-after-free (Zijun Hu)
- Clear secondary (not primary) EPC in pci_epc_remove_epf() when
removing the secondary controller associated with an NTB (Zijun Hu)
Cadence PCIe controller driver:
- Lower severity of 'phy-names' message (Bartosz Wawrzyniak)
Freescale i.MX6 PCIe controller driver:
- Fix suspend/resume support on i.MX6QDL, which has a hardware
erratum that prevents use of L2 (Stefan Eichenberger)
Intel VMD host bridge driver:
- Add 0xb60b and 0xb06f Device IDs for client SKUs (Nirmal Patel)
MediaTek PCIe Gen3 controller driver:
- Update mediatek-gen3 DT binding to require the exact number of
clocks for each SoC (Fei Shao)
- Add support for DT 'max-link-speed' and 'num-lanes' properties to
restrict the link speed and width (AngeloGioacchino Del Regno)
Microchip PolarFlare PCIe controller driver:
- Add DT and driver support for using either of the two PolarFire
Root Ports (Conor Dooley)
NVIDIA Tegra194 PCIe controller driver:
- Move endpoint controller cleanups that depend on refclk from the
host to the notifier that tells us the host has deasserted PERST#,
when refclk should be valid (Manivannan Sadhasivam)
Qualcomm PCIe controller driver:
- Add qcom SAR2130P DT binding with an additional clock (Dmitry
Baryshkov)
- Enable MSI interrupts if 'global' IRQ is supported, since a
previous commit unintentionally masked them (Manivannan Sadhasivam)
- Move endpoint controller cleanups that depend on refclk from the
host to the notifier that tells us the host has deasserted PERST#,
when refclk should be valid (Manivannan Sadhasivam)
- Add DT binding and driver support for IPQ9574, with Synopsys IP
v5.80a and Qcom IP 1.27.0 (devi priya)
- Move the OPP "operating-points-v2" table from the
qcom,pcie-sm8450.yaml DT binding to qcom,pcie-common.yaml, where it
can be used by other Qcom platforms (Qiang Yu)
- Add 'global' SPI interrupt for events like link-up, link-down to
qcom,pcie-x1e80100 DT binding so we can start enumeration when the
link comes up (Qiang Yu)
- Disable ASPM L0s for qcom,pcie-x1e80100 since the PHY is not tuned
to support this (Qiang Yu)
- Add ops_1_21_0 for SC8280X family SoC, which doesn't use the
'iommu-map' DT property and doesn't need BDF-to-SID translation
(Qiang Yu)
Rockchip PCIe controller driver:
- Define ROCKCHIP_PCIE_AT_SIZE_ALIGN to replace magic 256 endpoint
.align value (Damien Le Moal)
- When unmapping an endpoint window, compute the region index instead
of searching for it, and verify that the address was mapped (Damien
Le Moal)
- When mapping an endpoint window, verify that the address hasn't
been mapped already (Damien Le Moal)
- Implement pci_epc_ops.align_addr() for rockchip-ep (Damien Le Moal)
- Fix MSI IRQ data mapping to observe the alignment constraint, which
fixes intermittent page faults in memcpy_toio() and memcpy_fromio()
(Damien Le Moal)
- Rename rockchip_pcie_parse_ep_dt() to
rockchip_pcie_ep_get_resources() for consistency with similar DT
interfaces (Damien Le Moal)
- Skip the unnecessary link train in rockchip_pcie_ep_probe() and do
it only in the endpoint start operation (Damien Le Moal)
- Implement pci_epc_ops.stop_link() to disable link training and
controller configuration (Damien Le Moal)
- Attempt link training at 5 GT/s when both partners support it
(Damien Le Moal)
- Add a handler for PERST# signal so we can detect host-initiated
resets and start link training after PERST# is deasserted (Damien
Le Moal)
Synopsys DesignWare PCIe controller driver:
- Clear outbound address on unmap so dw_pcie_find_index() won't match
an ATU index that was already unmapped (Damien Le Moal)
- Use of_property_present() instead of of_property_read_bool() when
testing for presence of non-boolean DT properties (Rob Herring)
- Advertise 1MB size if endpoint supports Resizable BARs, which was
inadvertently lost in v6.11 (Niklas Cassel)
TI J721E PCIe driver:
- Add PCIe support for J722S SoC (Siddharth Vadapalli)
- Delay PCIE_T_PVPERL_MS (100 ms), not just PCIE_T_PERST_CLK_US (100
us), before deasserting PERST# to ensure power and refclk are
stable (Siddharth Vadapalli)
TI Keystone PCIe controller driver:
- Set the 'ti,keystone-pcie' mode so v3.65a devices work in Root
Complex mode (Kishon Vijay Abraham I)
- Try to avoid unrecoverable SError for attempts to issue config
transactions when the link is down; this is racy but the best we
can do (Kishon Vijay Abraham I)
Miscellaneous:
- Reorganize kerneldoc parameter names to match order in function
signature (Julia Lawall)
- Fix sysfs reset_method_store() memory leak (Todd Kjos)
- Simplify pci_create_slot() (Ilpo Järvinen)
- Fix incorrect printf format specifiers in pcitest (Luo Yifan)"
* tag 'pci-v6.13-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (127 commits)
PCI: rockchip-ep: Handle PERST# signal in EP mode
PCI: rockchip-ep: Improve link training
PCI: rockship-ep: Implement the pci_epc_ops::stop_link() operation
PCI: rockchip-ep: Refactor endpoint link training enable
PCI: rockchip-ep: Refactor rockchip_pcie_ep_probe() MSI-X hiding
PCI: rockchip-ep: Refactor rockchip_pcie_ep_probe() memory allocations
PCI: rockchip-ep: Rename rockchip_pcie_parse_ep_dt()
PCI: rockchip-ep: Fix MSI IRQ data mapping
PCI: rockchip-ep: Implement the pci_epc_ops::align_addr() operation
PCI: rockchip-ep: Improve rockchip_pcie_ep_map_addr()
PCI: rockchip-ep: Improve rockchip_pcie_ep_unmap_addr()
PCI: rockchip-ep: Use a macro to define EP controller .align feature
PCI: rockchip-ep: Fix address translation unit programming
PCI/pwrctrl: Rename pwrctrl functions and structures
PCI/pwrctrl: Rename pwrctl files to pwrctrl
PCI/pwrctl: Remove pwrctl device without iterating over all children of pwrctl parent
PCI/pwrctl: Ensure that pwrctl drivers are probed before PCI client drivers
PCI/pwrctl: Create pwrctl device only if at least one power supply is present
PCI/pwrctl: Use of_platform_device_create() to create pwrctl devices
tools: PCI: Fix incorrect printf format specifiers
...
These are a number of unrelated cleanups, generally simplifying the
architecture specific header files:
- A series from Al Viro simplifies asm/vga.h, after it turns out that
most of it can be generalized.
- A series from Julian Vetter adds a common version of
memcpy_{to,from}io() and memset_io() and changes most architectures
to use that instead of their own implementation
- A series from Niklas Schnelle concludes his work to make PC
style inb()/outb() optional
- Nicolas Pitre contributes improvements for the generic do_div()
helper
- Christoph Hellwig adds a generic version of page_to_phys()
and phys_to_page(), replacing the slightly different architecture
specific definitions.
- Uwe Kleine-Koenig has a minor cleanup for ioctl definitions
-----BEGIN PGP SIGNATURE-----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=zEHk
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic updates from Arnd Bergmann:
"These are a number of unrelated cleanups, generally simplifying the
architecture specific header files:
- A series from Al Viro simplifies asm/vga.h, after it turns out that
most of it can be generalized.
- A series from Julian Vetter adds a common version of
memcpy_{to,from}io() and memset_io() and changes most architectures
to use that instead of their own implementation
- A series from Niklas Schnelle concludes his work to make PC style
inb()/outb() optional
- Nicolas Pitre contributes improvements for the generic do_div()
helper
- Christoph Hellwig adds a generic version of page_to_phys() and
phys_to_page(), replacing the slightly different architecture
specific definitions.
- Uwe Kleine-Koenig has a minor cleanup for ioctl definitions"
* tag 'asm-generic-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (24 commits)
empty include/asm-generic/vga.h
sparc: get rid of asm/vga.h
asm/vga.h: don't bother with scr_mem{cpy,move}v() unless we need to
vt_buffer.h: get rid of dead code in default scr_...() instances
tty: serial: export serial_8250_warn_need_ioport
lib/iomem_copy: fix kerneldoc format style
hexagon: simplify asm/io.h for !HAS_IOPORT
loongarch: Use new fallback IO memcpy/memset
csky: Use new fallback IO memcpy/memset
arm64: Use new fallback IO memcpy/memset
New implementation for IO memcpy and IO memset
watchdog: Add HAS_IOPORT dependency for SBC8360 and SBC7240
__arch_xprod64(): make __always_inline when optimizing for performance
ARM: div64: improve __arch_xprod_64()
asm-generic/div64: optimize/simplify __div64_const32()
lib/math/test_div64: add some edge cases relevant to __div64_const32()
asm-generic: add an optional pfn_valid check to page_to_phys
asm-generic: provide generic page_to_phys and phys_to_page implementations
asm-generic/io.h: Remove I/O port accessors for HAS_IOPORT=n
tty: serial: handle HAS_IOPORT dependencies
...
-----BEGIN PGP SIGNATURE-----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=89Bg
-----END PGP SIGNATURE-----
Merge tag 'printk-for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux
Pull printk updates from Petr Mladek:
- Print more precise information about the printk log buffer memory
usage.
- Make sure that the sysrq title is shown on the console even when
deferred.
- Do not enable earlycon by `console=` which is meant to disable the
default console.
* tag 'printk-for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux:
printk: add dummy printk_force_console_enter/exit helpers
tty: sysrq: Use printk_force_console context on __handle_sysrq
printk: Introduce FORCE_CON flag
printk: Improve memory usage logging during boot
init: Don't proxy `console=` to earlycon
- Tree wide:
* Make nr_irqs static to the core code and provide accessor functions
to remove existing and prevent future aliasing problems with local
variables or function arguments of the same name.
- Core code:
* Prevent freeing an interrupt in the devres code which is not managed
by devres in the first place.
* Use seq_put_decimal_ull_width() for decimal values output in
/proc/interrupts which increases performance significantly as it
avoids parsing the format strings over and over.
* Optimize raising the timer and hrtimer soft interrupts by using the
'set bit only' variants instead of the combined version which checks
whether ksoftirqd should be woken up. The latter is a pointless
exercise as both soft interrupts are raised in the context of the
timer interrupt and therefore never wake up ksoftirqd.
* Delegate timer/hrtimer soft interrupt processing to a dedicated thread
on RT.
Timer and hrtimer soft interrupts are always processed in ksoftirqd
on RT enabled kernels. This can lead to high latencies when other
soft interrupts are delegated to ksoftirqd as well.
The separate thread allows to run them seperately under a RT
scheduling policy to reduce the latency overhead.
- Drivers:
* New drivers or extensions of existing drivers to support Renesas
RZ/V2H(P), Aspeed AST27XX, T-HEAD C900 and ATMEL sam9x7 interrupt
chips
* Support for multi-cluster GICs on MIPS.
MIPS CPUs can come with multiple CPU clusters, where each CPU cluster
has its own GIC (Generic Interrupt Controller). This requires to
access the GIC of a remote cluster through a redirect register block.
This is encapsulated into a set of helper functions to keep the
complexity out of the actual code paths which handle the GIC details.
* Support for encrypted guests in the ARM GICV3 ITS driver
The ITS page needs to be shared with the hypervisor and therefore
must be decrypted.
* Small cleanups and fixes all over the place
-----BEGIN PGP SIGNATURE-----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=JqxC
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2024-11-18' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull interrupt subsystem updates from Thomas Gleixner:
"Tree wide:
- Make nr_irqs static to the core code and provide accessor functions
to remove existing and prevent future aliasing problems with local
variables or function arguments of the same name.
Core code:
- Prevent freeing an interrupt in the devres code which is not
managed by devres in the first place.
- Use seq_put_decimal_ull_width() for decimal values output in
/proc/interrupts which increases performance significantly as it
avoids parsing the format strings over and over.
- Optimize raising the timer and hrtimer soft interrupts by using the
'set bit only' variants instead of the combined version which
checks whether ksoftirqd should be woken up. The latter is a
pointless exercise as both soft interrupts are raised in the
context of the timer interrupt and therefore never wake up
ksoftirqd.
- Delegate timer/hrtimer soft interrupt processing to a dedicated
thread on RT.
Timer and hrtimer soft interrupts are always processed in ksoftirqd
on RT enabled kernels. This can lead to high latencies when other
soft interrupts are delegated to ksoftirqd as well.
The separate thread allows to run them seperately under a RT
scheduling policy to reduce the latency overhead.
Drivers:
- New drivers or extensions of existing drivers to support Renesas
RZ/V2H(P), Aspeed AST27XX, T-HEAD C900 and ATMEL sam9x7 interrupt
chips
- Support for multi-cluster GICs on MIPS.
MIPS CPUs can come with multiple CPU clusters, where each CPU
cluster has its own GIC (Generic Interrupt Controller). This
requires to access the GIC of a remote cluster through a redirect
register block.
This is encapsulated into a set of helper functions to keep the
complexity out of the actual code paths which handle the GIC
details.
- Support for encrypted guests in the ARM GICV3 ITS driver
The ITS page needs to be shared with the hypervisor and therefore
must be decrypted.
- Small cleanups and fixes all over the place"
* tag 'irq-core-2024-11-18' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (50 commits)
irqchip/riscv-aplic: Prevent crash when MSI domain is missing
genirq/proc: Use seq_put_decimal_ull_width() for decimal values
softirq: Use a dedicated thread for timer wakeups on PREEMPT_RT.
timers: Use __raise_softirq_irqoff() to raise the softirq.
hrtimer: Use __raise_softirq_irqoff() to raise the softirq
riscv: defconfig: Enable T-HEAD C900 ACLINT SSWI drivers
irqchip: Add T-HEAD C900 ACLINT SSWI driver
dt-bindings: interrupt-controller: Add T-HEAD C900 ACLINT SSWI device
irqchip/stm32mp-exti: Use of_property_present() for non-boolean properties
irqchip/mips-gic: Fix selection of GENERIC_IRQ_EFFECTIVE_AFF_MASK
irqchip/mips-gic: Prevent indirect access to clusters without CPU cores
irqchip/mips-gic: Multi-cluster support
irqchip/mips-gic: Setup defaults in each cluster
irqchip/mips-gic: Support multi-cluster in for_each_online_cpu_gic()
irqchip/mips-gic: Replace open coded online CPU iterations
genirq/irqdesc: Use str_enabled_disabled() helper in wakeup_show()
genirq/devres: Don't free interrupt which is not managed by devres
irqchip/gic-v3-its: Fix over allocation in itt_alloc_pool()
irqchip/aspeed-intc: Add AST27XX INTC support
dt-bindings: interrupt-controller: Add support for ASPEED AST27XX INTC
...
When CONFIG_DMA_ENGINE is disabled, the driver now fails to build:
drivers/tty/serial/amba-pl011.c: In function 'pl011_unthrottle_rx':
drivers/tty/serial/amba-pl011.c:1822:16: error: 'struct uart_amba_port' has no member named 'using_rx_dma'
1822 | if (uap->using_rx_dma) {
| ^~
drivers/tty/serial/amba-pl011.c:1823:20: error: 'struct uart_amba_port' has no member named 'dmacr'
1823 | uap->dmacr |= UART011_RXDMAE;
| ^~
drivers/tty/serial/amba-pl011.c:1824:32: error: 'struct uart_amba_port' has no member named 'dmacr'
1824 | pl011_write(uap->dmacr, uap, REG_DMACR);
| ^~
Add the missing #ifdef check around these field accesses, matching
what other parts of this driver do.
Fixes: 2bcacc1c87 ("serial: amba-pl011: Fix RX stall when DMA is used")
Cc: stable <stable@kernel.org>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202411140617.nkjeHhsK-lkp@intel.com/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20241115110021.744332-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to the platform's new project uart ip upgrade,
the new project's timeout interrupt needs to use bit17
while other projects' timeout interrupt needs to use
bit13, using private data to adapt and be compatible
with all projects.
Signed-off-by: Wenhua Lin <Wenhua.Lin@unisoc.com>
Link: https://lore.kernel.org/r/20241113110516.2166328-2-Wenhua.Lin@unisoc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function pl011_throttle_rx() calls pl011_stop_rx() to disable RX, which
also disables the RX DMA by clearing the RXDMAE bit of the DMACR
register. However, to properly unthrottle RX when DMA is used, the
function pl011_unthrottle_rx() is expected to set the RXDMAE bit of
the DMACR register, which it currently lacks. This causes RX to stall
after the throttle API is called.
Set RXDMAE bit in the DMACR register while unthrottling RX if RX DMA is
used.
Fixes: 211565b100 ("serial: pl011: UPSTAT_AUTORTS requires .throttle/unthrottle")
Cc: stable@vger.kernel.org
Signed-off-by: Kartik Rajput <kkartik@nvidia.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20241113092629.60226-1-kkartik@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 7c0cca7c84 ("tty: ldisc: add sysctl to prevent autoloading of
ldiscs") introduces the tty_ldisc_autoload sysctl with the wrong
proc_handler. .extra1 and .extra2 parameters are set to avoid other values
thant SYSCTL_ZERO or SYSCTL_ONE to be set but proc_dointvec do not uses
them.
This commit fixes this by using proc_dointvec_minmax instead of
proc_dointvec.
Fixes: 7c0cca7c84 ("tty: ldisc: add sysctl to prevent autoloading of ldiscs")
Cc: stable <stable@kernel.org>
Signed-off-by: Nicolas Bouchinet <nicolas.bouchinet@ssi.gouv.fr>
Reviewed-by: Lin Feng <linf@wangsu.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20241112131357.49582-4-nicolas.bouchinet@clip-os.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The F81216E is a LPC/eSPI to 4 UART Super I/O and is mostly compatible with
the F81216H, but does not support RS-485 auto-direction delays on any port.
Signed-off-by: Filip Brozovic <fbrozovic@gmail.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20241110111703.15494-1-fbrozovic@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By using the printk_force_console the loglevel workaround can be removed.
The workaround existed to always send the sysrq header message to all
consoles not matter what was the current loglevel, but it won't work for
deferred messages, since the loglevel can be restore before the message
is printed, suppressing the message that wasn't supposed to be
suppressed by the workaround.
Signed-off-by: Marcos Paulo de Souza <mpdesouza@suse.com>
Reviewed-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20241105-printk-loud-con-v2-2-bd3ecdf7b0e4@suse.com
Signed-off-by: Petr Mladek <pmladek@suse.com>
The early_console_setup() function initializes the sci_ports[0].port with
an object of type struct uart_port obtained from the object of type
struct earlycon_device received as argument by the early_console_setup().
It may happen that later, when the rest of the serial ports are probed,
the serial port that was used as earlycon (e.g., port A) to be mapped to a
different position in sci_ports[] and the slot 0 to be used by a different
serial port (e.g., port B), as follows:
sci_ports[0] = port A
sci_ports[X] = port B
In this case, the new port mapped at index zero will have associated data
that was used for earlycon.
In case this happens, after Linux boot, any access to the serial port that
maps on sci_ports[0] (port A) will block the serial port that was used as
earlycon (port B).
To fix this, add early_console_exit() that clean the sci_ports[0] at
earlycon exit time.
Fixes: 0b0cced19a ("serial: sh-sci: Add CONFIG_SERIAL_EARLYCON support")
Cc: stable@vger.kernel.org
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20241106120118.1719888-4-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify the request port function by using a single call
to devm_platform_ioremap_resource().
This will also enhance the printing from /proc/iomem:
cat /proc/iomem | grep flexcom ; cat /proc/iomem | grep serial
f0004000-f00041ff : f0004000.flexcom flexcom@f0004000
f8020000-f80201ff : f8020000.flexcom flexcom@f8020000
f0004200-f00043ff : f0004200.serial serial@200
f8020200-f80203ff : f8020200.serial serial@200
fffff200-fffff3ff : fffff200.serial serial@fffff200
Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
Tested-by: Andrei Simion <andrei.simion@microchip.com>
Reviewed-by: Hari Prasath Gujulan Elango <hari.prasathge@microchip.com>
Link: https://lore.kernel.org/r/20241105131946.22449-1-mihai.sain@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently in omap_8250_shutdown, the dma->rx_running flag is
set to zero in omap_8250_rx_dma_flush. Next pm_runtime_get_sync
is called, which is a runtime resume call stack which can
re-set the flag. When the call omap_8250_shutdown returns, the
flag is expected to be UN-SET, but this is not the case. This
is causing issues the next time UART is re-opened and
omap_8250_rx_dma is called. Fix by moving pm_runtime_get_sync
before the omap_8250_rx_dma_flush.
cc: stable@vger.kernel.org
Fixes: 0e31c8d173 ("tty: serial: 8250_omap: add custom DMA-RX callback")
Signed-off-by: Bin Liu <b-liu@ti.com>
[Judith: Add commit message]
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20241031172315.453750-1-jm@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add serial driver data for Exynos8895 SoC. The main difference from
other platforms is that fifosize is only specified via the
samsung,uart-fifosize DT property.
Signed-off-by: Ivaylo Ivanov <ivo.ivanov.ivanov1@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20241023090902.538040-3-ivo.ivanov.ivanov1@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SG2044 relys on an internal divisor when calculating bitrate, which
means a wrong clock for the most common bitrates. So add a quirk for
this uart device to skip the set rate call and only relys on the
internal UART divisor.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Inochi Amaoto <inochiama@gmail.com>
Link: https://lore.kernel.org/r/20241024062105.782330-4-inochiama@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of multiple Altera JTAG UART ports available on the system, the
error message will contain information about the port for which
attaching the IRQ handler failed.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20241029130307.5003-1-tklauser@distanz.ch
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of multiple Altera UART ports available on the system, the error
message will contain information about the port for which attaching the
IRQ handler failed.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20241029130258.4679-1-tklauser@distanz.ch
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pcim_iomap_table() and pcim_iomap_regions_request_all() have been
deprecated by the PCI subsystem in commit e354bb84a4 ("PCI: Deprecate
pcim_iomap_table(), pcim_iomap_regions_request_all()").
Replace these functions with their successors, pcim_iomap() and
pcim_request_all_regions().
Link: https://lore.kernel.org/r/20241030112743.104395-9-pstanner@redhat.com
Signed-off-by: Philipp Stanner <pstanner@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
The newly added function is used from a loadable module, so it has
to be exported the same way as the other function in this file:
ERROR: modpost: "serial_8250_warn_need_ioport" [drivers/tty/serial/8250/8250_pci.ko] undefined!
Fixes: 7c7e6c8924 ("tty: serial: handle HAS_IOPORT dependencies")
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
In a future patch HAS_IOPORT=n will disable inb()/outb() and friends at
compile time. We thus need to add HAS_IOPORT as dependency for those
drivers using them unconditionally. Some 8250 serial drivers support
MMIO only use, so fence only the parts requiring I/O ports and print an
error message if a device can't be supported with the current
configuration.
Co-developed-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Use the irq_get_nr_irqs() function instead of the global variable
'nr_irqs'. Prepare for changing 'nr_irqs' from an exported global
variable into a variable with file scope.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20241015190953.1266194-18-bvanassche@acm.org
Use the irq_get_nr_irqs() function instead of the global variable
'nr_irqs'. Prepare for changing 'nr_irqs' from an exported global
variable into a variable with file scope.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20241015190953.1266194-17-bvanassche@acm.org
Use the irq_get_nr_irqs() function instead of the global variable
'nr_irqs'. Prepare for changing 'nr_irqs' from an exported global
variable into a variable with file scope.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20241015190953.1266194-16-bvanassche@acm.org
Use the irq_get_nr_irqs() function instead of the global variable
'nr_irqs'. Prepare for changing 'nr_irqs' from an exported global
variable into a variable with file scope.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20241015190953.1266194-15-bvanassche@acm.org
Use the irq_get_nr_irqs() function instead of the global variable
'nr_irqs'. Prepare for changing 'nr_irqs' from an exported global
variable into a variable with file scope.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20241015190953.1266194-14-bvanassche@acm.org
Use the irq_get_nr_irqs() function instead of the global variable
'nr_irqs'. Prepare for changing 'nr_irqs' from an exported global
variable into a variable with file scope.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20241015190953.1266194-13-bvanassche@acm.org
Remove the old exar_ee_read() and associated helper functions.
Remove defines that are no longer needed after the switch to using the
eeprom_93cx6 driver.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Parker Newman <pnewman@connecttech.com>
Link: https://lore.kernel.org/r/ed756c48965a95ce3384ebb7fe2441b4928b4510.1727880931.git.pnewman@connecttech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace the custom 93cx6 EEPROM read functions with the eeprom_93cx6
driver. This removes duplicate code and improves code readability.
Replace exar_ee_read() calls with eeprom_93cx6_read() or
eeprom_93cx6_multiread().
Add "select EEPROM_93CX6" to config SERIAL_8250_EXAR to ensure
eeprom_93cx6 driver is also compiled when 8250_exar driver is selected.
Note: Old exar_ee_read() and associated functions are removed in next
patch in this series.
Link to mailing list discussion with Andy Shevchenko for reference.
Link: https://lore.kernel.org/linux-serial/Ztr5u2wEt8VF1IdI@black.fi.intel.com/
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Parker Newman <pnewman@connecttech.com>
Link: https://lore.kernel.org/r/1bf2214ae27130ca58b9e779c4d65a0e5db06fc1.1727880931.git.pnewman@connecttech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop the unnecessary "_sys" infix from the suspend PM ops.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20241009145110.16847-10-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Serial drivers should not be dropping characters themselves, but at
least drop the unused 'drop' parameter from the receive handler for now.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20241009145110.16847-9-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop the unnecessary WARN() in case the TTY buffers are ever full in
favour of a rate limited dev_err() which doesn't kill the machine when
panic_on_warn is set.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20241009145110.16847-8-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The receiver is supposed to be enabled in the startup() callback and not
in set_termios() which is called also during console setup.
This specifically avoids accepting input before the port has been opened
(and interrupts enabled), something which can also break the GENI
firmware (cancel fails and after abort, the "stale" counter handling
appears to be broken so that later input is not processed until twelve
chars have been received).
There also does not appear to be any need to keep the receiver disabled
while updating the port settings.
Since commit 6f3c3cafb1 ("serial: qcom-geni: disable interrupts during
console writes") the calls to manipulate the secondary interrupts, which
were done without holding the port lock, can also lead to the receiver
being left disabled when set_termios() races with the console code (e.g.
when init opens the tty during boot). This can manifest itself as a
serial getty not accepting input.
The calls to stop and start rx in set_termios() can similarly race with
DMA completion and, for example, cause the DMA buffer to be unmapped
twice or the mapping to be leaked.
Fix this by only enabling the receiver during startup and while holding
the port lock to avoid racing with the console code.
Fixes: 6f3c3cafb1 ("serial: qcom-geni: disable interrupts during console writes")
Fixes: 2aaa43c707 ("tty: serial: qcom-geni-serial: add support for serial engine DMA")
Fixes: c4f528795d ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Cc: stable@vger.kernel.org # 6.3
Cc: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20241009145110.16847-6-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to wait for the DMA transfer to complete when cancelling the
rx command on stop_rx(). This specifically prevents the DMA completion
interrupt from firing after rx has been restarted, something which can
lead to an IOMMU fault and hosed rx when the interrupt handler unmaps
the DMA buffer for the new command:
qcom_geni_serial 988000.serial: serial engine reports 0 RX bytes in!
arm-smmu 15000000.iommu: FSR = 00000402 [Format=2 TF], SID=0x563
arm-smmu 15000000.iommu: FSYNR0 = 00210013 [S1CBNDX=33 WNR PLVL=3]
Bluetooth: hci0: command 0xfc00 tx timeout
Bluetooth: hci0: Reading QCA version information failed (-110)
Also add the missing state machine reset which is needed in case
cancellation fails.
Fixes: 2aaa43c707 ("tty: serial: qcom-geni-serial: add support for serial engine DMA")
Cc: stable@vger.kernel.org # 6.3
Cc: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20241009145110.16847-5-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A commit adding back the stopping of tx on port shutdown failed to add
back the locking which had also been removed by commit e83766334f
("tty: serial: qcom_geni_serial: No need to stop tx/rx on UART
shutdown").
Holding the port lock is needed to serialise against the console code,
which may update the interrupt enable register and access the port
state.
Fixes: d8aca2f968 ("tty: serial: qcom-geni-serial: stop operations in progress at shutdown")
Fixes: 947cc4ecc0 ("serial: qcom-geni: fix soft lockup on sw flow control and suspend")
Cc: stable@vger.kernel.org # 6.3
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20241009145110.16847-4-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 35781d8356.
Hibernation is not supported on Qualcomm platforms with mainline
kernels yet a broken vendor implementation for the GENI serial driver
made it upstream.
This is effectively dead code that cannot be tested and should just be
removed, but if these paths were ever hit for an open non-console port
they would crash the machine as the driver would fail to enable clocks
during restore() (i.e. all ports would have to be closed by drivers and
user space before hibernating the system to avoid this as a comment in
the code hinted at).
The broken implementation also added a random call to enable the
receiver in the port setup code where it does not belong and which
enables the receiver prematurely for console ports.
Fixes: 35781d8356 ("tty: serial: qcom-geni-serial: Add support for Hibernation feature")
Cc: stable@vger.kernel.org # 6.2
Cc: Aniket Randive <quic_arandive@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20241009145110.16847-3-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The polled console (KGDB/KDB) implementation must not call port setup
unconditionally as the port may already be in use by the console or a
getty.
Only make sure that the receiver is enabled, but do not enable any
device interrupts.
Fixes: d8851a96ba ("tty: serial: qcom-geni-serial: Add a poll_init() function")
Cc: stable@vger.kernel.org # 6.4
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20241009145110.16847-2-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When sending data using DMA at high baudrate (4 Mbdps in local test case) to
a device with small RX buffer which keeps asserting RTS after every received
byte, it is possible that the iMX UART driver would not recognize the falling
edge of RTS input signal and get stuck, unable to transmit any more data.
This condition happens when the following sequence of events occur:
- imx_uart_mctrl_check() is called at some point and takes a snapshot of UART
control signal status into sport->old_status using imx_uart_get_hwmctrl().
The RTSS/TIOCM_CTS bit is of interest here (*).
- DMA transfer occurs, the remote device asserts RTS signal after each byte.
The i.MX UART driver recognizes each such RTS signal change, raises an
interrupt with USR1 register RTSD bit set, which leads to invocation of
__imx_uart_rtsint(), which calls uart_handle_cts_change().
- If the RTS signal is deasserted, uart_handle_cts_change() clears
port->hw_stopped and unblocks the port for further data transfers.
- If the RTS is asserted, uart_handle_cts_change() sets port->hw_stopped
and blocks the port for further data transfers. This may occur as the
last interrupt of a transfer, which means port->hw_stopped remains set
and the port remains blocked (**).
- Any further data transfer attempts will trigger imx_uart_mctrl_check(),
which will read current status of UART control signals by calling
imx_uart_get_hwmctrl() (***) and compare it with sport->old_status .
- If current status differs from sport->old_status for RTS signal,
uart_handle_cts_change() is called and possibly unblocks the port
by clearing port->hw_stopped .
- If current status does not differ from sport->old_status for RTS
signal, no action occurs. This may occur in case prior snapshot (*)
was taken before any transfer so the RTS is deasserted, current
snapshot (***) was taken after a transfer and therefore RTS is
deasserted again, which means current status and sport->old_status
are identical. In case (**) triggered when RTS got asserted, and
made port->hw_stopped set, the port->hw_stopped will remain set
because no change on RTS line is recognized by this driver and
uart_handle_cts_change() is not called from here to unblock the
port->hw_stopped.
Update sport->old_status in __imx_uart_rtsint() accordingly to make
imx_uart_mctrl_check() detect such RTS change. Note that TIOCM_CAR
and TIOCM_RI bits in sport->old_status do not suffer from this problem.
Fixes: ceca629e0b ("[ARM] 2971/1: i.MX uart handle rts irq")
Cc: stable <stable@kernel.org>
Reviewed-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20241002184133.19427-1-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
