In the snippets like the following
if (...)
return / goto / break / continue ...;
else
...
the 'else' is redundant. Get rid of it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230721170022.3461-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
min() has strict type checking and preferred over min_t() for
unsigned types to avoid overflow. Here it's unclear why min_t()
was chosen since both variables are of the same type. In any
case update to use min().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230721170022.3461-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Define and init voltage configuration bits. Those bits are inited in
vendor boot code (bl2, bl33) already so do it in the driver to not depend
on other code.
Introduced bits:
REG11[0] - selects Vref. 0 - calibration voltage, 1 - VDDA. txlx and later
SoCs support VDDA or calibration voltage as Vref, but others
support only calibration voltage. For newer platforms vendor
uses VDDA as default.
REG11[1] - reserved bit. g12a and later SoCs must write 1, others SoCs
write 0.
REG11[5] - Vref voltage. 0 - 0.9v, 1 - 1.8v. g12a and later SoCs must
write 0, others SoCs write 1.
REG11[6] - selects common-mode voltage, 0: from AVDD, 1: from Vref.
g12a and later SoCs must write 0, others SoCs write 1.
Signed-off-by: George Stark <gnstark@sberdevices.ru>
Link: https://lore.kernel.org/r/20230715110654.6035-4-gnstark@sberdevices.ru
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Disable internal continuous ring counter at init stage. Disable value
depends on SoC family: gxl and later SoCs write 1, others write 0.
This bit are inited in vendor boot code (bl2, bl33) already so do it
in the driver to not depend on other code.
Signed-off-by: George Stark <gnstark@sberdevices.ru>
Link: https://lore.kernel.org/r/20230715110654.6035-3-gnstark@sberdevices.ru
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Set up input channels 0,1 muxes in the same way as for the channels 2-7
later in the code.
Signed-off-by: George Stark <gnstark@sberdevices.ru>
Link: https://lore.kernel.org/r/20230715110654.6035-2-gnstark@sberdevices.ru
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Simplify the probe() by replacing of_device_get_match_data() and
i2c_match_id() by i2c_get_match_data() as we have similar I2C
and DT-based matching table.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Puranjay Mohan <puranjay12@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230716175218.130557-2-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add IIO channel for all muxed inputs of channel 7.
Meson saradc channel 7 is connected to a mux that can switch input
to well-known sources like Vdd, GND and several Vdd dividers.
Signed-off-by: George Stark <GNStark@sberdevices.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230714114010.293440-7-gnstark@sberdevices.ru
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add channel labels to provide human-readable names for the inputs.
Signed-off-by: George Stark <GNStark@sberdevices.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230714114010.293440-6-gnstark@sberdevices.ru
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Channels could be referenced in the driver code and using enum allows
to make it more robust.
Signed-off-by: George Stark <GNStark@sberdevices.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230714114010.293440-5-gnstark@sberdevices.ru
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
meson_sar_adc_set_chan7_mux is a basic func() for writing single register,
defined as static. Moved it up so it could be used in more places.
Signed-off-by: George Stark <GNStark@sberdevices.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230714114010.293440-4-gnstark@sberdevices.ru
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Allow to use enum items for variables initialization.
For this, move enums upper in the code.
Signed-off-by: George Stark <GNStark@sberdevices.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230714114010.293440-3-gnstark@sberdevices.ru
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove IIO_CHAN_SOFT_TIMESTAMP channel because it's used only for
buffering mode which is not implemented.
Signed-off-by: George Stark <GNStark@sberdevices.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230714114010.293440-2-gnstark@sberdevices.ru
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds pressure compensation to the scd4x driver. The pressure can
be written to the sensor in hPa. The pressure will be compensated
internally by the sensor.
Signed-off-by: Roan van Dijk <roan@protonic.nl>
Link: https://lore.kernel.org/r/20230711101419.2065107-1-roan@protonic.nl
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In `iio_trigger_detach_poll_func()` the return value from
`trig->ops->set_trigger_state(trig, false)` is checked with `if (ret)`.
However, in `iio_trigger_attach_poll_func()` it is checked with
`if (ret < 0)`. Resolve this mismatch by only checking for `if (ret)` in
both places.
Signed-off-by: Waqar Hameed <waqar.hameed@axis.com>
Link: https://lore.kernel.org/r/pndv8eojdey.fsf@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Each of qcom,spmi-adc7-pm*.h headers define a set of ADC channels that
can be used for monitoring on thie particular chip. Switch them to use
channel IDs defined in the dt-bindings/iio/qcom,spmi-vadc.h header
instead of specifying the numeric IDs.
Suggested-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230707123027.1510723-2-dmitry.baryshkov@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Enable buffered reading of samples from the LMP92064 ADC.
The main benefit of this change is being able to read out current and
voltage measurements in a single transfer, allowing instantaneous power
measurements.
Reads into the buffer can be triggered by any software triggers, e.g.
the iio-trig-hrtimer:
$ mkdir /sys/kernel/config/iio/triggers/hrtimer/my-trigger
$ cat /sys/bus/iio/devices/iio\:device3/name
lmp92064
$ iio_readdev -t my-trigger -b 16 iio:device3 | hexdump
WARNING: High-speed mode not enabled
0000000 0000 0176 0101 0001 5507 abd5 7645 1768
0000010 0000 016d 0101 0001 ee1e ac6b 7645 1768
...
Signed-off-by: Leonard Göhrs <l.goehrs@pengutronix.de>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230707063635.1496437-1-l.goehrs@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230704095808.33780-1-frank.li@vivo.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Even though it existed in bindings for the longest time,
ADC5_GPIO2_100K_PU was never assigned in the driver. Do so.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230627-topic-adc-v1-1-c61581abffa3@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When processing data read the full fifo data in 1 time. If there
are several samples in the FIFO, it means we are experiencing
system delay. In this case, it is better to read all data with 1
bus access than to add additional latency by doing several ones.
This requires to use a bigger buffer depending on chip FIFO size
and do an additional local data copy before sending. But the cost
is minimal and behavior is still better like this under system
heavy load.
Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Link: https://lore.kernel.org/r/20230623082924.283967-1-inv.git-commit@tdk.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Datarate (dr) is a 3-bit wide register field. Values from 0 to 7 are
allowed for all devices but only for the ADS1115 devices a value of 7
does make a difference.
While on it fix the description of the datarate for ADS1115 devices as
well.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230621160857.3400747-1-m.felsch@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Replace scnprintf with sysfs_emit_at which is the preferred alternative.
Also make sure each fractional digit is in its place by padding with
zeros up to 3 digits: "...%03d...".
Signed-off-by: Alisa Roman <alisa.roman@analog.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230620163135.93780-1-alisa.roman@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Allwinner's D1/T113s/R329/T507 SoCs have a new general purpose ADC.
This ADC is the same for all of this SoCs. The only difference is
the number of available channels.
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Link: https://lore.kernel.org/r/20230619154252.3951913-4-bigunclemax@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The General Purpose ADC (GPADC) can convert the external signal into
a certain proportion of digital value, to realize the measurement of
analog signal, which can be applied to power detection and key detection.
Theoretically, this ADC can support up to 16 channels. All SoCs below
contain this GPADC IP. The only difference between them is the number
of available channels:
T113 - 1 channel
D1 - 2 channels
R329 - 4 channels
T507 - 4 channels
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Link: https://lore.kernel.org/r/20230619154252.3951913-3-bigunclemax@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The calibration bias is setting the LED current to change the detection
distance. Add read/write attribute for proximity calibration bias and
read attribute for available values. This is supported for vcnl4040 and
vcnl4200.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-9-astrid.rost@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add the proximity multi pulse (PS_MPS) as oversampling_ratio.
Instead of one single pulse per every defined time frame, one can
program2, 4, or even 8 pulses. This leads to a longer IRED on-time
for each proximity measurement value, which also results in a higher
detection range.
Add read/write attribute for proximity oversampling-ratio and read
attribute for available oversampling-ratio.
This is supported for vcnl4040 and vcnl4200.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-8-astrid.rost@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add read/write attribute for proximity and illuminance period. The
period is set in the interrupt persistence flags(PS_PERS and ALS_PERS).
An interrupt will not be asserted if the raw value is not over (or lower)
than the threshold for the set continued amount of measurements.
The time in seconds is calculated by the number of continued refreshes
multiplied with the integration time.
It will always pick the next lower possible value. The period changes,
if the integration time is changed.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-7-astrid.rost@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support to configure ambient light sensor interrupts and threshold
limits for vcnl4040 and vcnl4200. If an interrupt is detected an event
will be pushed to the event interface.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-6-astrid.rost@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add illuminance integration time for vcnl4040 and vcnl4200.
Add read/write attribute for illuminance integration time and read
attribute for available integration times.
Set scale and sampling rate according to the integration time.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-5-astrid.rost@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Check IIO_PROXIMITY with switch case in order to make it easier
to add further types like light.
Add check for IIO_EV_INFO_VALUE for writing rising or falling events.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-4-astrid.rost@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add ps_it attributes for vcnl4200 (similar to vcnl4040).
Add read/write attribute for proximity integration time.
Read attribute for available proximity integration times.
Change sampling rate depending on integration time.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-3-astrid.rost@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add proximity interrupt support for vcnl4200 (similar to vcnl4040).
Add support to configure proximity sensor interrupts and threshold
limits. If an interrupt is detected an event will be pushed to the
event interface.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-2-astrid.rost@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The DA217 accelerometer is another DA280 compatible accelerometer,
add its device-ids to the da280 driver.
Reported-by: Juno Computers USA <usa@junocomputers.com>
Tested-by: Juno Computers USA <usa@junocomputers.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230613094346.162551-1-hdegoede@redhat.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Replace timestamping by the new common inv_sensors timestamp
module. The principle behind is the same but the implementation in
the new module is far better providing less jitter and a better
estimation.
Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230606162147.79667-5-inv.git-commit@tdk.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Create new inv_sensors common modules and move inv_icm42600
timestamp module inside. This module will be used by IMUs and
also in the future by other chips.
Modify inv_icm42600 driver to use timestamp module and do some
headers cleanup.
Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230606162147.79667-3-inv.git-commit@tdk.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move icm42600 dependent function inside the core module.
Do some headers cleanup at the same time.
Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230606162147.79667-2-inv.git-commit@tdk.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Print read and expected device ID as debug warning.
Add error check for ad_sd_init() result.
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Signed-off-by: Markus Burri <markus.burri@mt.com>
Link: https://lore.kernel.org/r/20230614073033.2497318-1-markus.burri@mt.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
If st->mclk is not NULL, then st->clock_sel is either AD7192_CLK_EXT_MCLK2
or AD7192_CLK_EXT_MCLK1_2.
So devm_clk_get_optional_enabled() can be used instead of hand writing it.
This saves some line of code.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/7dbe973905f1fdae5d2f5ae5a3b01dd1d6a9925b.1686774340.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reference iio.yaml schema from dtschema to allow already used
label property:
sc7180-trogdor-pazquel360-lte.dtb: proximity@28: 'label' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230617103658.114453-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reference iio.yaml schema from dtschema to allow already used
label property:
sc7180-trogdor-homestar-r4.dtb: proximity@28: 'label' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230617103658.114453-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We just sorted the entries and fields last release, so just out of a
perverse sense of curiosity, I decided to see if we can keep things
ordered for even just one release.
The answer is "No. No we cannot".
I suggest that all kernel developers will need weekly training sessions,
involving a lot of Big Bird and Sesame Street. And at the yearly
maintainer summit, we will all sing the alphabet song together.
I doubt I will keep doing this. At some point "perverse sense of
curiosity" turns into just a cold dark place filled with sadness and
despair.
Repeats: 80e62bc8487b ("MAINTAINERS: re-sort all entries and fields")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- swiotlb area sizing fixes (Petr Tesarik)
-----BEGIN PGP SIGNATURE-----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=4Lfc
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-6.5-2023-07-09' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping fixes from Christoph Hellwig:
- swiotlb area sizing fixes (Petr Tesarik)
* tag 'dma-mapping-6.5-2023-07-09' of git://git.infradead.org/users/hch/dma-mapping:
swiotlb: reduce the number of areas to match actual memory pool size
swiotlb: always set the number of areas before allocating the pool
boot reordering work
-----BEGIN PGP SIGNATURE-----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=RZFV
-----END PGP SIGNATURE-----
Merge tag 'x86_urgent_for_v6.5_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fpu fix from Borislav Petkov:
- Do FPU AP initialization on Xen PV too which got missed by the recent
boot reordering work
* tag 'x86_urgent_for_v6.5_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/xen: Fix secondary processors' FPU initialization
On shutdown or kexec, the kernel tries to park the non-boot CPUs with an
INIT IPI. But the same code path is also used by the crash utility. If the
CPU which panics is not the boot CPU then it sends an INIT IPI to the boot
CPU which resets the machine. Prevent this by validating that the CPU which
runs the stop mechanism is the boot CPU. If not, leave the other CPUs in
HLT.
-----BEGIN PGP SIGNATURE-----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=DOCF
-----END PGP SIGNATURE-----
Merge tag 'x86-core-2023-07-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fix from Thomas Gleixner:
"A single fix for the mechanism to park CPUs with an INIT IPI.
On shutdown or kexec, the kernel tries to park the non-boot CPUs with
an INIT IPI. But the same code path is also used by the crash utility.
If the CPU which panics is not the boot CPU then it sends an INIT IPI
to the boot CPU which resets the machine.
Prevent this by validating that the CPU which runs the stop mechanism
is the boot CPU. If not, leave the other CPUs in HLT"
* tag 'x86-core-2023-07-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/smp: Don't send INIT to boot CPU
* Fix an uninitialized variable warning.
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQ2qTKExjcn+O1o2YRKO3ySh0YRpgUCZKjUjwAKCRBKO3ySh0YR
pn92AQC4gY9GOyKcc/aiAd/t1u8gGxnFtcN06xh4TdVArMM4/AD/UtEKx9LYuaSF
pyhw5SfzxI555HfXkA8ci/D+BxguVQs=
=/vX1
-----END PGP SIGNATURE-----
Merge tag 'xfs-6.5-merge-6' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs fix from Darrick Wong:
"Nothing exciting here, just getting rid of a gcc warning that I got
tired of seeing when I turn on gcov"
* tag 'xfs-6.5-merge-6' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: fix uninit warning in xfs_growfs_data
-----BEGIN PGP SIGNATURE-----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=F8D0
-----END PGP SIGNATURE-----
Merge tag '6.5-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6
Pull more smb client updates from Steve French:
- fix potential use after free in unmount
- minor cleanup
- add worker to cleanup stale directory leases
* tag '6.5-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Add a laundromat thread for cached directories
smb: client: remove redundant pointer 'server'
cifs: fix session state transition to avoid use-after-free issue
