The 'stop endpoint' command timer was started when a 'stop endpoint'
command was added to the command queue.
This can trigger unwanted timeouts if there are several pending commands
in the queue that xHC needs to handle first.
The generic command timer, which was added later than the 'stop endpoint'
timeout timer, times each command currently being handled by xHC hardware.
A timed out stop endpoint command was treated as a more severe issue than
other failed commands, so the separate stop endpoint timer was left
unchanged.
Use the generic command timer for stop endpoint commands. Identify if
the timed out command was a stop endpoint command in the generic handler,
and treat it with the same severity as earlier.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220511220450.85367-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Activate the just added extension for xhci-plat and omit the shared
hcd if either of the root hubs has no ports.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220511220450.85367-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch prepares xhci-plat for the following scenario
- If either of the root hubs has no ports, then omit shared hcd
- Main hcd can be USB3 if there are no USB2 ports
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220511220450.85367-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is in preparation of an extension where in case of a
root hub with no ports no shared hcd will be created.
Whether one of the root hubs has no ports we figure our in
usb_add_hcd() for the primary hcd. Therefore create the shared hcd
only after this call.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220511220450.85367-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch prepares xhci for the following scenario:
- If either of the root hubs has no ports, then omit shared hcd
- Main hcd can be USB3 if there are no USB2 ports
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220511220450.85367-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Factoring out parts of xhci_gen_setup() has two motivations:
- When adding functionaliy to omit shared hcd if not needed in a
subsequent patch, we'll have to call xhci_hcd_init_usb3_data()
from two places.
- It reduces size of xhci_gen_setup() and makes it better readable.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220511220450.85367-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set "HCD_FLAG_DEFER_RH_REGISTER" to hcd->flags in xhci_run() to defer
registering primary roothub in usb_add_hcd() if xhci has two roothubs.
This will make sure both primary roothub and secondary roothub will be
registered along with the second HCD.
This is required for cold plugged USB devices to be detected in certain
PCIe USB cards (like Inateck USB card connected to AM64 EVM or J7200 EVM).
This patch has been added and reverted earier as it triggered a race
in usb device enumeration.
That race is now fixed in 5.16-rc3, and in stable back to 5.4
commit 6cca13de26ee ("usb: hub: Fix locking issues with address0_mutex")
commit 6ae6dc22d2d1 ("usb: hub: Fix usb enumeration issue due to address0
race")
[minor rebase change, and commit message update -Mathias]
CC: stable@vger.kernel.org # 5.4+
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Chris Chiu <chris.chiu@canonical.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20220510091630.16564-3-kishon@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It has been observed with certain PCIe USB cards (like Inateck connected
to AM64 EVM or J7200 EVM) that as soon as the primary roothub is
registered, port status change is handled even before xHC is running
leading to cold plug USB devices not detected. For such cases, registering
both the root hubs along with the second HCD is required. Add support for
deferring roothub registration in usb_add_hcd(), so that both primary and
secondary roothubs are registered along with the second HCD.
This patch has been added and reverted earier as it triggered a race
in usb device enumeration.
That race is now fixed in 5.16-rc3, and in stable back to 5.4
commit 6cca13de26ee ("usb: hub: Fix locking issues with address0_mutex")
commit 6ae6dc22d2d1 ("usb: hub: Fix usb enumeration issue due to address0
race")
CC: stable@vger.kernel.org # 5.4+
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Chris Chiu <chris.chiu@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20220510091630.16564-2-kishon@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch resolves kernel-doc warnings to add return value description
in function comments.
Addressed warnings:
drivers/usb/host/ehci-xilinx-of.c:37: warning: No description found for return value of 'ehci_xilinx_port_handed_over'
drivers/usb/host/ehci-xilinx-of.c:117: warning: No description found for return value of 'ehci_hcd_xilinx_of_probe'
drivers/usb/host/ehci-xilinx-of.c:201: warning: No description found for return value of 'ehci_hcd_xilinx_of_remove'
Signed-off-by: Piyush Mehta <piyush.mehta@xilinx.com>
Link: https://lore.kernel.org/r/20220509170252.28271-1-piyush.mehta@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes the unused variables assignment warning.
Value assigned to variable bufferspace is overwritten, before
it can be used. This makes such variable assignment useless.
Reported Coverity warning: UNUSED_VALUE
Signed-off-by: Piyush Mehta <piyush.mehta@xilinx.com>
Link: https://lore.kernel.org/r/20220506175349.10102-1-piyush.mehta@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch resolves checkpatch warnings for xilinx EHCI driver.
Addressed warnings:
WARNING: quoted string split across lines
50: FILE: drivers/usb/host/ehci-xilinx-of.c:50:
+ "The USB host controller does not support full speed "
+ "nor low speed devices\n");
WARNING: quoted string split across lines
53: FILE: drivers/usb/host/ehci-xilinx-of.c:53:
+ "You can reconfigure the host controller to have "
+ "full speed support\n");
Signed-off-by: Piyush Mehta <piyush.mehta@xilinx.com>
Link: https://lore.kernel.org/r/20220510132252.26001-1-piyush.mehta@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Putting USB gadgets on a new bus of their own encounters a problem
when multiple gadgets are present: They all have the same name! The
driver core fails with a "sys: cannot create duplicate filename" error
when creating any of the /sys/bus/gadget/devices/<gadget-name>
symbolic links after the first.
This patch fixes the problem by adding a ".N" suffix to each gadget's
name when the gadget is registered (where N is a unique ID number),
thus making the names distinct.
Reported-and-tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: fc274c1e9973 ("USB: gadget: Add a new bus for gadgets")
Link: https://lore.kernel.org/r/YnqKAXKyp9Vq/pbn@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lubbock is the only machine that has three IRQs for the UDC.
These are currently hardcoded in the driver based on a
machine header file.
Change this to use platform device resources as we use for
the generic IRQ anyway.
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Returning an error value in an i2c remove callback results in an error
message being emitted by the i2c core, but otherwise it doesn't make a
difference. The device goes away anyhow and the devm cleanups are
called.
In this case the remove callback even returns early without stopping the
tcpm worker thread and various timers. A work scheduled on the work
queue, or a firing timer after tcpci_remove() returned probably results
in a use-after-free situation because the regmap and driver data were
freed. So better make sure that tcpci_unregister_port() is called even
if disabling the irq failed.
Also emit a more specific error message instead of the i2c core's
"remove failed (EIO), will be ignored" and return 0 to suppress the
core's warning.
This patch is (also) a preparation for making i2c remove callbacks
return void.
Fixes: 3ba76256fc4e ("usb: typec: tcpci: mask event interrupts when remove driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220502080456.21568-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cdc-wdm tracks whether a response reading request is in-progress and
blocks the next request from being sent until the previous request is
completed. As soon as last user closes the cdc-wdm device file, the
driver cancels any ongoing requests, resets the pending response
counter, but leaves the response reading in-progress flag
(WDM_RESPONDING) untouched.
So if the user closes the device file during the response receive
request is being performed, no more data will be obtained from the
modem. The request will be cancelled, effectively preventing the
WDM_RESPONDING flag from being reseted. Keeping the flag set will
prevent a new response receive request from being sent, permanently
blocking the read path. The read path will staying blocked until the
module will be reloaded or till the modem will be re-attached.
This stuck has been observed with a Huawei E3372 modem attached to an
OpenWrt router and using the comgt utility to set up a network
connection.
Fix this issue by clearing the WDM_RESPONDING flag on the device file
close.
Without this fix, the device reading stuck can be easily reproduced in a
few connection establishing attempts. With this fix, a load test for
modem connection re-establishing worked for several hours without any
issues.
Fixes: 922a5eadd5a3 ("usb: cdc-wdm: Fix race between autosuspend and reading from the device")
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20220501175828.8185-1-ryazanov.s.a@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just like the header is tracking the formats in a linked list, in this
patch we track the frames in a linked list of the formats. It
simplifies the parsing of the configfs structure.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220421211427.3400834-6-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The functions and structs of the configfs interface should also be used
by the uvc gadget driver. This patch prepares the stack by moving the
common structs and functions to the common header file.
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220421211427.3400834-5-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some configfs variables like bDefaultFrameIndex are always starting by
1. This patch adds a check to prevent setting those variables to 0.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220421211427.3400834-4-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the controller hasn't DMA'ed the Setup data from its fifo, it won't
process the End Transfer command. Polling for the command completion may
block the driver from servicing the Setup phase and cause a timeout.
Previously we only check and delay issuing End Transfer in the case of
endpoint dequeue. Let's do that for all End Transfer scenarios.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/2fcf3b5d90068d549589a57a27a79f76c6769b04.1650593829.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver shouldn't be able to issue End Transfer to the control
endpoint at anytime. Typically we should only do so in error cases such
as invalid/unexpected direction of Data Phase as described in the
control transfer flow of the programming guide. It _may_ end started
data phase during controller deinitialization from soft disconnect or
driver removal. However, that should not happen because the driver
should be maintained in EP0_SETUP_PHASE during driver tear-down. On
soft-connect, the controller should be reset from a soft-reset and there
should be no issue starting the control endpoint.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/3c6643678863a26702e4115e9e19d7d94a30d49c.1650593829.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we can't guarantee that the host won't send new Setup packet
before going through the device-initiated disconnect, don't prepare
beyond the Setup stage and keep the device in EP0_SETUP_PHASE. This
ensures that the device-initated disconnect sequence can go through
gracefully. Note that the controller won't service the End Transfer
command if it can't DMA out the Setup packet.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/6bacec56ecabb2c6e49a09cedfcac281fdc97de0.1650593829.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the GEVNTCOUNT indicates events in the event buffer, the driver needs
to acknowledge them before the controller can halt. Simply let the
interrupt handler acknowledges the remaining event generated by the
controller while polling for DSTS.DEVCTLHLT. This avoids disabling irq
and taking care of race condition between the interrupt handlers and
pullup().
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/ea306ec93c41ccafbdb5d16404ff3b6eca299613.1650593829.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't do soft-disconnect if it's previously done. Likewise, don't do
soft-connect if the device is currently connected and running. It would
break normal operation.
Currently the caller of pullup() (udc's sysfs soft_connect) only checks
if it had initiated disconnect to prevent repeating soft-disconnect. It
doesn't check for soft-connect. To be safe, let's keep the check here
regardless whether the udc core is fixed.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/1c1345bd66c97a9d32f77d63aaadd04b7b037143.1650593829.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a USB GPIO based reset for dwc3-xilinx driver. The PHY
needs to be reset after the completion of phy initialization. As part
of the reset, check for gpio-reset binding before toggling the pin.
This feature is advantageous when the user toggle GPIO to trigger the
ULPI-PHY reset.
Delay of milliseconds is added in between low and high to meet the setup
and hold time requirement of the reset. The reset-gpio error handling is
added for error notification.
Some GPIO controllers must be accessed using message-based buses, like
I2C or SPI, to address this problem, updates GPIO access with sleep API.
This reset is specific to the zynqMp.
Signed-off-by: Piyush Mehta <piyush.mehta@xilinx.com>
Link: https://lore.kernel.org/r/20220504075309.6244-3-piyush.mehta@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is no longer needed. The sysdev pointer is now used when
assigning the ACPI companions to the xHCI ports and USB
devices.
Assigning the ACPI companion here resulted in the
fwnode->secondary pointer to be replaced also for the parent
dwc3 device since the primary fwnode (the ACPI companion)
was shared. That was unintentional and it created potential
side effects like resource leaks.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220428111056.3558-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The controller device (hcd) does not always have the ACPI
companion assigned to it at all. We can not rely on it when
finding the ACPI companion for the root hub. Instead we need
to use the sysdev pointer.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220428111056.3558-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After moving the omap1 platform into generalized multiplatform
support on ARM, the kernel test robot points out a W=1 warning that
now shows up in more configurations:
drivers/usb/host/ehci-omap.c:64:19: warning: unused function 'ehci_read'
The function was last used 9 years ago and can just be removed.
Fixes: 87425ad36330 ("USB: ehci-omap: Remove PHY reset handling code")
Reported-by: kernel test robot <lkp@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20220428102314.950323-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently when driver->match_existing_only is true, the error return is
set to -EBUSY however ret is then set to 0 at the end of the if/else
statement. I believe the ret = 0 statement should be set in the else
part of the if statement and not at the end to ensure -EBUSY is being
returned correctly.
Detected by clang scan:
drivers/usb/gadget/udc/core.c:1558:4: warning: Value stored to 'ret' is
never read [deadcode.DeadStores]
Fixes: fc274c1e9973 ("USB: gadget: Add a new bus for gadgets")
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20220504135840.232209-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UDC driver should not touch gadget's driver internals, especially it
should not reset driver->bus. This wasn't harmful so far, but since
commit fc274c1e9973 ("USB: gadget: Add a new bus for gadgets") gadget
subsystem got it's own bus and messing with ->bus triggers the
following NULL pointer dereference:
dwc2 12480000.hsotg: bound driver g_ether
8<--- cut here ---
Unable to handle kernel NULL pointer dereference at virtual address 00000000
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in: ...
CPU: 0 PID: 620 Comm: modprobe Not tainted 5.18.0-rc5-next-20220504 #11862
Hardware name: Samsung Exynos (Flattened Device Tree)
PC is at module_add_driver+0x44/0xe8
LR is at sysfs_do_create_link_sd+0x84/0xe0
...
Process modprobe (pid: 620, stack limit = 0x(ptrval))
...
module_add_driver from bus_add_driver+0xf4/0x1e4
bus_add_driver from driver_register+0x78/0x10c
driver_register from usb_gadget_register_driver_owner+0x40/0xb4
usb_gadget_register_driver_owner from do_one_initcall+0x44/0x1e0
do_one_initcall from do_init_module+0x44/0x1c8
do_init_module from load_module+0x19b8/0x1b9c
load_module from sys_finit_module+0xdc/0xfc
sys_finit_module from ret_fast_syscall+0x0/0x54
Exception stack(0xf1771fa8 to 0xf1771ff0)
...
dwc2 12480000.hsotg: new device is high-speed
---[ end trace 0000000000000000 ]---
Fix this by removing driver->bus entry reset.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20220505104618.22729-1-m.szyprowski@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The latency is an unsigned int and should be printed as such (even if it
only holds values in the range 0..255).
Signed-off-by: Daniels Umanovskis <du@axentia.se>
Link: https://lore.kernel.org/r/20220426123714.2000-1-du@axentia.se
[ johan: amend commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Add the device id for the HPLM930Display which is a PL2303GC based
device.
Signed-off-by: Scott Chen <scott@labau.com.tw>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
This reverts commit 0298b4b95cb373c21e6323c905589f8dac42c5b4.
The series still has built errors as reported in linux-next, so revert
it for now.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/20220502210728.0b36f3cd@canb.auug.org.au
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Matthias Kaehlcke <mka@chromium.org>
Cc: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Cc: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit c40b62216c1aecc0dc00faf33d71bd71cb440337.
The series still has built errors as reported in linux-next, so revert
it for now.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/20220502210728.0b36f3cd@canb.auug.org.au
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmJu9FYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGAyEH/16xtJSpLmLwrQzG
o+4ToQxSQ+/9UHyu0RTEvHg2THm9/8emtIuYyc/5FgdoWctcSa3AaDcveWmuWmkS
KYcdhfJsaEqjNHS3OPYXN84fmo9Hel7263shu5+IYmP/sN0DfQp6UWTryX1q4B3Q
4Pdutkuq63Uwd8nBZ5LXQBumaBrmkkuMgWEdT4+6FOo1mPzwdIGBxCuz1UsNNl5k
chLWxkQfe2eqgWbYJrgCQfrVdORXVtoU2fGilZUNrHRVGkkldXkkz5clJfapyZD3
odmZCEbrE4GPKgZwCmDERMfD1hzhZDtYKiHfOQ506szH5ykJjPBcOjHed7dA60eB
J3+wdek=
=39Ca
-----END PGP SIGNATURE-----
Merge 5.18-rc5 into usb-next
We need the USB fixes in here, and this resolves a merge issue in
drivers/usb/dwc3/drd.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UCSI mailbox is always in main memory.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
While support for working with a vbus was added, the regulator was never
actually gotten (despite what was documented). Fix this by actually
getting the supply from the device tree.
Fixes: 7acc9973e3c4 ("usb: phy: generic: add vbus support")
Cc: stable <stable@kernel.org>
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20220425171412.1188485-3-sean.anderson@seco.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the user sets the usb_request's no_interrupt, then there will be no
completion event for the request. Currently the driver incorrectly uses
the event status of a different request to report the status for a
request with no_interrupt. The dwc3 driver needs to check the TRB status
associated with the request when reporting its status.
Note: this is only applicable to missed_isoc TRB completion status, but
the other status are also listed for completeness/documentation.
Fixes: 6d8a019614f3 ("usb: dwc3: gadget: check for Missed Isoc from event status")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/db2c80108286cfd108adb05bad52138b78d7c3a7.1650673655.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Call onboard_hub_create/destroy_pdevs() from usb_add/remove_hcd()
for primary HCDs to create/destroy platform devices for onboard
USB hubs that may be connected to the root hub of the controller.
These functions are a NOP unless CONFIG_USB_ONBOARD_HUB=y/m.
Also add a field to struct usb_hcd to keep track of the onboard hub
platform devices that are owned by the HCD.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20220217104219.v21.3.I7a3a7d9d2126c34079b1cab87aa0b2ec3030f9b7@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The main issue this driver addresses is that a USB hub needs to be
powered before it can be discovered. For discrete onboard hubs (an
example for such a hub is the Realtek RTS5411) this is often solved
by supplying the hub with an 'always-on' regulator, which is kind
of a hack. Some onboard hubs may require further initialization
steps, like changing the state of a GPIO or enabling a clock, which
requires even more hacks. This driver creates a platform device
representing the hub which performs the necessary initialization.
Currently it only supports switching on a single regulator, support
for multiple regulators or other actions can be added as needed.
Different initialization sequences can be supported based on the
compatible string.
Besides performing the initialization the driver can be configured
to power the hub off during system suspend. This can help to extend
battery life on battery powered devices which have no requirements
to keep the hub powered during suspend. The driver can also be
configured to leave the hub powered when a wakeup capable USB device
is connected when suspending, and power it off otherwise.
Technically the driver consists of two drivers, the platform driver
described above and a very thin USB driver that subclasses the
generic driver. The purpose of this driver is to provide the platform
driver with the USB devices corresponding to the hub(s) (a hub
controller may provide multiple 'logical' hubs, e.g. one to support
USB 2.0 and another for USB 3.x).
Note: the current series only supports hubs connected directly to
a root hub, support for other configurations could be added if
needed.
Co-developed-by: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20220217104219.v21.2.I7c9a1f1d6ced41dd8310e8a03da666a32364e790@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a "gadget" bus and uses it for registering gadgets and
their drivers. From now on, bindings will be managed by the driver
core rather than through ad-hoc manipulations in the UDC core.
As part of this change, the driver_pending_list is removed. The UDC
core won't need to keep track of unbound drivers for later binding,
because the driver core handles all of that for us.
However, we do need one new feature: a way to prevent gadget drivers
from being bound to more than one gadget at a time. The existing code
does this automatically, but the driver core doesn't -- it's perfectly
happy to bind a single driver to all the matching devices on the bus.
The patch adds a new bitflag to the usb_gadget_driver structure for
this purpose.
A nice side effect of this change is a reduction in the total lines of
code, since now the driver core will do part of the work that the UDC
used to do.
A possible future patch could add udc devices to the gadget bus, say
as a separate device type.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/YmSpdxaDNeC2BBOf@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes some minor mistakes in the UDC core's kerneldoc.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/YmSpKpnWR8WWEk/p@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for adding a "gadget" bus, this patch reverses the
order of registration of udc and gadget devices in usb_add_gadget().
The current code adds the gadget device first, probably because that
was more convenient at the time and the order didn't really matter.
But with the upcoming change, adding the gadget will cause driver
probing to occur. Unwinding that on the error pathway will become
much more obtrusive, not to mention the fact that a gadget driver
might not work properly before the udc is registered. It's better to
register the udc device first, particularly since that doesn't involve
a bus or driver binding and therefore is simpler to unwind.
For symmetry, the order of unregistration in usb_del_gadget() is
likewise reversed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/YmSo6fU1FlNq8cOZ@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
