If the APLIC driver is probed before the IMSIC driver, the parent MSI
domain will be missing, which causes a NULL pointer dereference in
msi_create_device_irq_domain().
Avoid this by deferring probe until the parent MSI domain is available. Use
dev_err_probe() to avoid printing an error message when returning
-EPROBE_DEFER.
Fixes: ca8df97fe6 ("irqchip/riscv-aplic: Add support for MSI-mode")
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20241114200133.3069460-1-samuel.holland@sifive.com
Add ACPI support in APLIC drivers. Use the mapping created early during
boot to get the details about the APLIC.
Signed-off-by: Sunil V L <sunilvl@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Tested-by: Björn Töpel <bjorn@rivosinc.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://patch.msgid.link/20240812005929.113499-17-sunilvl@ventanamicro.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The section 4.5.2 of the RISC-V AIA specification says that "any write
to a sourcecfg register of an APLIC might (or might not) cause the
corresponding interrupt-pending bit to be set to one if the rectified
input value is high (= 1) under the new source mode."
When the interrupt type is changed in the sourcecfg register, the APLIC
device might not set the corresponding pending bit, so the interrupt might
never become pending.
To handle sourcecfg register changes for level-triggered interrupts in MSI
mode, manually set the pending bit for retriggering interrupt so it gets
retriggered if it was already asserted.
Fixes: ca8df97fe6 ("irqchip/riscv-aplic: Add support for MSI-mode")
Signed-off-by: Yong-Xuan Wang <yongxuan.wang@sifive.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Vincent Chen <vincent.chen@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/20240809071049.2454-1-yongxuan.wang@sifive.com
The RISC-V advanced platform-level interrupt controller (APLIC) has
two modes of operation: 1) Direct mode and 2) MSI mode.
(For more details, refer https://github.com/riscv/riscv-aia)
In APLIC MSI-mode, wired interrupts are forwared as message signaled
interrupts (MSIs) to CPUs via IMSIC.
Extend the existing APLIC irqchip driver to support MSI-mode for
RISC-V platforms having both wired interrupts and MSIs.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Björn Töpel <bjorn@rivosinc.com>
Reviewed-by: Björn Töpel <bjorn@rivosinc.com>
Link: https://lore.kernel.org/r/20240307140307.646078-8-apatel@ventanamicro.com
