These error paths return success but they need to return a negative
error code.
Fixes: 7a96b6ea90a4 ("usb: musb: Add support for PolarFire SoC's musb controller")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YrVmLEc/FOEzNdzj@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Meteor Lake TCSS(Type-C Subsystem) xHCI needs to be runtime suspended
whenever possible to allow the TCSS hardware block to enter D3cold and
thus save energy.
Cc: stable@kernel.org
Signed-off-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220623111945.1557702-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the same way as Intel Alder Lake TCSS (Type-C Subsystem) the Raptor
Lake TCSS xHCI needs to be runtime suspended whenever possible to
allow the TCSS hardware block to enter D3cold and thus save energy.
Cc: stable@kernel.org
Signed-off-by: Tanveer Alam <tanveer1.alam@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220623111945.1557702-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If ports are not turned off in shutdown then runtime suspended
self-powered USB devices may survive in U3 link state over S5.
During subsequent boot, if firmware sends an IPC command to program
the port in DISCONNECT state, it will time out, causing significant
delay in the boot time.
Turning off roothub port power is also recommended in xhci
specification 4.19.4 "Port Power" in the additional note.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220623111945.1557702-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
irq is disabled in xhci_quiesce(called by xhci_halt, with bit:2 cleared
in USBCMD register), but xhci_run(called by usb_add_hcd) re-enable it.
It's possible that you will receive thousands of interrupt requests
after initialization for 2.0 roothub. And you will get a lot of
warning like, "xHCI dying, ignoring interrupt. Shouldn't IRQs be
disabled?". This amount of interrupt requests will cause the entire
system to freeze.
This problem was first found on a device with ASM2142 host controller
on it.
[tidy up old code while moving it, reword header -Mathias]
Cc: stable@kernel.org
Signed-off-by: Hongyu Xie <xiehongyu1@kylinos.cn>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220623111945.1557702-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some new modem device ids and support for further PL2303
device types.
All but the final commit (RM500K device id) have been in linux-next and
with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCYrRX4AAKCRALxc3C7H1l
CB+fAQD1h5BRHdaCJ2vTarMGbL95lcZqdw1l4NRLgHe68csH+QEAlo32t2D26d9r
MEgGvtAeHgPDoATxQk20c1PVHgDe4wE=
=lbN1
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.19-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.19-rc4
Here are some new modem device ids and support for further PL2303
device types.
All but the final commit (RM500K device id) have been in linux-next and
with no reported issues.
* tag 'usb-serial-5.19-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Quectel RM500K module support
USB: serial: option: add Quectel EM05-G modem
USB: serial: pl2303: add support for more HXN (G) types
USB: serial: option: add Telit LE910Cx 0x1250 composition
This merges the movement of the octeon-usb driver out of
drivers/staging/ into drivers/usb.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* 'staging-octeon' of gitolite.kernel.org:/pub/scm/linux/kernel/git/gregkh/staging:
staging: octeon-usb: move driver out of staging
For code neat purpose, we can use kmemdup to replace
kmalloc + memcpy.
Signed-off-by: Slark Xiao <slark_xiao@163.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add support for further HXN (G) type devices (GT variant, GL variant, GS
variant and GR) and document the bcdDevice mapping.
Note that the TA and TB types use the same bcdDevice as some GT and GE
variants, respectively, but that the HX status request can be used to
determine which is which.
Also note that we currently do not distinguish between the various HXN
(G) types in the driver but that this may change eventually (e.g. when
adding GPIO support).
Reported-by: Charles Yeh <charlesyeh522@gmail.com>
Link: https://lore.kernel.org/r/YrF77b9DdeumUAee@hovoldconsulting.com
Cc: stable@vger.kernel.org # 5.13
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The Target Peripheral List (TPL) is used to identify targeted devices
during Embedded Host compliance testing. The user can add "tpl-support"
in the device tree to enable it.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Link: https://lore.kernel.org/r/20220621152350.145745-5-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Target Peripheral List (TPL) is used to identify targeted devices
during Embedded Host compliance testing. The user can add "tpl-support"
in the device tree to enable it.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20220621152350.145745-3-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Target Peripheral List (TPL) is used to identify targeted devices
during Embedded Host compliance testing. The user can add "tpl-support"
in the device tree to enable it.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20220621152350.145745-2-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Octeon usb driver has been in staging for a long time and used in
Ubiquiti routers for a while now.
It's been built and then tested on real hardware with several usb devices
and it is proven to be stable and ready to be moved to its proper place
in the kernel tree.
Move it to drivers/usb/host and adjust its Makefile, Kconfig and defconfig
dependencies.
Many thanks to the developers who made it happen.
Signed-off-by: Artur Bujdoso <artur.bujdoso@gmail.com>
Link: https://lore.kernel.org/r/Yo0HBIlSXOBM+//9@crux
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dev_err_probe() to simplify handling errors in ci_hdrc_imx_probe()
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20220614120522.1469957-1-alexander.stein@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The chipidea udc core is capable of reading the current frame index from
hardware. This patch adds the get_frame callback to the driver.
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220616194459.2981519-1-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I found the "argument" typo.
It seems that "argument" is more correct than "arguement".
Signed-off-by: Hyunwoo Kim <imv4bel@gmail.com>
Link: https://lore.kernel.org/r/20220621064242.GA698757@ubuntu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In musb_{save|restore}_context() the expression '&musb->endpoints[i]' just
cannot be NULL, so the checks have no sense at all -- after dropping them,
the local variables 'hw_ep' are no longer necessary, so drop them as well.
Found by Linux Verification Center (linuxtesting.org) with the SVACE static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/3f8f60d9-f1b5-6b2c-1222-39b156151a22@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In usbhs_rza1_hardware_init(), of_find_node_by_name() will return
a node pointer with refcount incremented. We should use of_node_put()
when it is not used anymore.
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20220618023205.4056548-1-windhl@126.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In ohci_hcd_ppc_of_probe(), of_find_compatible_node() will return
a node pointer with refcount incremented. We should use of_node_put()
when it is not used anymore.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20220617034637.4003115-1-windhl@126.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Loosen the typec_mux_match() requirements so that searches where an
alt mode is not specified, but the target mux device lists the
"mode-switch" property, return a success.
This is helpful in Type C port drivers which would like to get a pointer
to the mux switch associated with a Type C port, but don't want to
specify a particular alt mode.
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220615172129.1314056-2-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If dwc3 is wakeup capable, keep the power domain always ON so that
wakeup from system suspend can be supported. Otherwise, keep the
power domain ON only during runtime suspend to support wakeup from
runtime suspend.
Reviewed-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Signed-off-by: Sandeep Maheswaram <quic_c_sanm@quicinc.com>
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Link: https://lore.kernel.org/r/1655094654-24052-6-git-send-email-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Configure DP/DM line interrupts based on the USB2 device attached to
the root hub port. When HS/FS device is connected, configure the DP line
as falling edge to detect both disconnect and remote wakeup scenarios. When
LS device is connected, configure DM line as falling edge to detect both
disconnect and remote wakeup. When no device is connected, configure both
DP and DM lines as rising edge to detect HS/HS/LS device connect scenario.
Reviewed-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Sandeep Maheswaram <quic_c_sanm@quicinc.com>
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Link: https://lore.kernel.org/r/1655094654-24052-5-git-send-email-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check wakeup-source property for dwc3 core node to set the
wakeup capability. Drop the device_init_wakeup call from
runtime suspend and resume.
If the dwc3 is wakeup capable, don't power down the USB PHY(s).
The glue drivers are expected to take care of configuring the
additional wakeup settings if needed based on the dwc3 wakeup
capability status. In some SOC designs, powering off the PHY is
resulting in higher leakage, so this patch save power on such boards.
Reviewed-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Signed-off-by: Sandeep Maheswaram <quic_c_sanm@quicinc.com>
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Link: https://lore.kernel.org/r/1655094654-24052-3-git-send-email-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Synopsys IP DWC_usb32 and DWC_usb31 version 1.90a and above deprecated
GCTL.CORESOFTRESET. The DRD mode switching flow is updated to remove the
GCTL soft reset. Add version checks to prevent using deprecated setting
in mode switching flow.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/9df529fde6e55f5508321b6bc26e92848044ef2b.1655338967.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The print function dev_err() is redundant because platform_get_irq()
already prints an error.
This was found by coccicheck:
./drivers/usb/gadget/udc/aspeed_udc.c:1546:2-9: line 1546 is redundant because platform_get_irq() already prints an error.
Acked-by: Neal Liu <neal_liu@aspeedtech.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Link: https://lore.kernel.org/r/20220616090410.128483-1-jiapeng.chong@linux.alibaba.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a couple of spelling mistakes, one in a dev_warn message
and another in a SETUP_DBG message. Fix these and remove an extraneous
white space too.
Acked-by: Neal Liu <neal_liu@aspeedtech.com>
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20220615073518.192827-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "chunk >= 0" condition does not work because count is a u32.
Also, really we shouldn't enter the loop when "chunk" is zero.
Once that condition is fixed then there is no need for the "last"
variable. I reversed the "if (chunk <= ep->chunk_max)" as well.
The new loop is much simpler.
Fixes: 055276c13205 ("usb: gadget: add Aspeed ast2600 udc driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/Yq2SvM2bbrtSd1H9@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel SoC PMIC is a generic name for all PMICs that are used
on Intel platforms. In particular, INTEL_SOC_PMIC kernel configuration
option refers to Crystal Cove PMIC, which has never been a part
of any Intel Broxton hardware. Drop wrong dependency from Kconfig.
Note, the correct dependency is satisfied via ACPI PMIC OpRegion driver,
which the Type-C depends on.
Fixes: d2061f9cc32d ("usb: typec: add driver for Intel Whiskey Cove PMIC USB Type-C PHY")
Reported-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220620104316.57592-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A panic can occur if the endpoint becomes disabled and the
uvcg_video_pump adds the request back to the req_free list after it has
already been queued to the endpoint. The endpoint complete will add the
request back to the req_free list. Invalidate the local request handle
once it's been queued.
<6>[ 246.796704][T13726] configfs-gadget gadget: uvc: uvc_function_set_alt(1, 0)
<3>[ 246.797078][ T26] list_add double add: new=ffffff878bee5c40, prev=ffffff878bee5c40, next=ffffff878b0f0a90.
<6>[ 246.797213][ T26] ------------[ cut here ]------------
<2>[ 246.797224][ T26] kernel BUG at lib/list_debug.c:31!
<6>[ 246.807073][ T26] Call trace:
<6>[ 246.807180][ T26] uvcg_video_pump+0x364/0x38c
<6>[ 246.807366][ T26] process_one_work+0x2a4/0x544
<6>[ 246.807394][ T26] worker_thread+0x350/0x784
<6>[ 246.807442][ T26] kthread+0x2ac/0x320
Fixes: f9897ec0f6d3 ("usb: gadget: uvc: only pump video data if necessary")
Cc: stable@vger.kernel.org
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dan Vacura <w36195@motorola.com>
Link: https://lore.kernel.org/r/20220617163154.16621-1-w36195@motorola.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In a report for a separate bug (which has already been fixed by commit
5f0b5f4d50fa "usb: gadget: fix race when gadget driver register via
ioctl") in the raw-gadget driver, the syzbot console log included
error messages caused by attempted registration of a new driver with
the same name as an existing driver:
> kobject_add_internal failed for raw-gadget with -EEXIST, don't try to register things with the same name in the same directory.
> UDC core: USB Raw Gadget: driver registration failed: -17
> misc raw-gadget: fail, usb_gadget_register_driver returned -17
These errors arise because raw_gadget.c registers a separate UDC
driver for each of the UDC instances it creates, but these drivers all
have the same name: "raw-gadget". Until recently this wasn't a
problem, but when the "gadget" bus was added and UDC drivers were
registered on this bus, it became possible for name conflicts to cause
the registrations to fail. The reason is simply that the bus code in
the driver core uses the driver name as a sysfs directory name (e.g.,
/sys/bus/gadget/drivers/raw-gadget/), and you can't create two
directories with the same pathname.
To fix this problem, the driver names used by raw-gadget are made
distinct by appending a unique ID number: "raw-gadget.N", with a
different value of N for each driver instance. And to avoid the
proliferation of error handling code in the raw_ioctl_init() routine,
the error return paths are refactored into the common pattern (goto
statements leading to cleanup code at the end of the routine).
Link: https://lore.kernel.org/all/0000000000008c664105dffae2eb@google.com/
Fixes: fc274c1e9973 "USB: gadget: Add a new bus for gadgets"
CC: Andrey Konovalov <andreyknvl@gmail.com>
CC: <stable@vger.kernel.org>
Reported-and-tested-by: syzbot+02b16343704b3af1667e@syzkaller.appspotmail.com
Reviewed-by: Andrey Konovalov <andreyknvl@gmail.com>
Acked-by: Hillf Danton <hdanton@sina.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/YqdG32w+3h8c1s7z@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit df22ecc41b54def624735b83784857e708bd1502.
If CONFIG_GENERIC_PHY is not enabled, then the devm_phy_get() returns
-ENOSYS. Don't remove this check.
Fixes: df22ecc41b54 ("usb: dwc3: Remove the checks of -ENOSYS")
Cc: Kushagra Verma <kushagra765@outlook.com>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/eb1df7ef954b5af093c0528982db52a41df18615.1655255152.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of walking the list of children of an ACPI device directly
in order to find the child matching a given bus address, use
acpi_find_child_by_adr() for this purpose.
Also notice that if acpi_find_child_by_adr() doesn't find a matching
child, acpi_find_child_device() will not find it too, so directly
replace usb_acpi_find_port() in usb_acpi_get_companion_for_port() with
acpi_find_child_by_adr() and drop it entirely.
Apart from simplifying the code, this will help to eliminate the
children list head from struct acpi_device as it is redundant and it
is used in questionable ways in some places (in particular, locking is
needed for walking the list pointed to it safely, but it is often
missing).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmKvgdceHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG0qMH/RnVz4BvYXVWWc1t
+4NT9N20pNzrByzUxSBsrLfL5BNIt9fNjrS0WLs4HlzExbiixvKIBHPkDZoCo1gQ
wxoqpJf2BMxmdXH46/wWdSszbdPk33eLM/MfYE2QfnmtYsDSLZQMzOUAcdh6qD53
ty9br3IM/g4ixCwxKRt3NNixjin4wTTxR5ZD2E5k0JAaT+4FW5llRvq92dA1UOq7
JeGRLkc2l0211MFLo0vtuPOyWMIQL8t98rKTzevwoVY7R9I/0uUJCbkU7mb9wMUY
yKYlTN/4ZikTTSxa8NpQsXHqTyOHaKmS5F6oE4sw9VurHI2u3Jmxy9j9AwO1Pn8C
JUizMCk=
=qqcu
-----END PGP SIGNATURE-----
Merge v5.19-rc3 into usb-next
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Aspeed udc is compliant with USB2.0, supports USB High Speed
and Full Speed, backward compatible with USB1.1.
Supports independent DMA channel for each generic endpoint.
Supports 32/256 stages descriptor mode for all generic endpoints.
This driver supports full functionality including single/multiple
stages descriptor mode, and exposes 1 UDC gadget driver.
Signed-off-by: Neal Liu <neal_liu@aspeedtech.com>
Link: https://lore.kernel.org/r/20220523030134.2977116-2-neal_liu@aspeedtech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The host needs to tell the device the exit latencies using the SET_SEL
request before device initiated link powermanagement can be enabled.
The exit latency values do not change after enumeration, it's enough
to set them once. So do like Windows 10 and issue the SET_SEL request
once just before setting the configuration.
This is also the sequence described in USB 3.2 specs "9.1.2 Bus
enumeration". SET_SEL is issued once before the Set Configuration
request, and won't be cleared by the Set Configuration,
Set Interface or ClearFeature (STALL) requests.
Only warm reset, hot reset, set Address 0 clears the exit latencies.
See USB 3.2 section 9.4.14 Table 9-10 Device parameters and events
Add udev->lpm_devinit_allow, and set it if SET_SEL was successful.
If not set, then don't try to enable device initiated LPM
We used to issue a SET_SEL request every time lpm is enabled for either
U1 or U2 link states, meaning a SET_SEL was issued twice after every
Set Configuration and Set Interface requests, easily accumulating to
over 15 SET_SEL requets during a USB3 webcam enumeration.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220506161807.3369439-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Register both the port and partner USB Power Delivery
Capabilities so they are exposed to the user space.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220502132058.86236-4-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All the USB Type-C Connector Class devices are protected, so
the drivers can not directly access them. This will adds a
few helpers that can be used to link the ports and partners
to the correct USB Power Delivery objects.
For ports a new optional sysfs attribute file is also added
that can be used to select the USB Power Delivery
capabilities that the port will advertise to the partner.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220502132058.86236-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introducing a small device class for USB Power Delivery.
The idea with it is that we do not mix any more USB Power
Delivery information into the USB Type-C connectors only.
This separation will make it possible to register USB Power
Delivery devices also from other places, for example from
USB Type-C Bridges (see USB Type-C Bridge Specification).
The device class will not always deal with only the messages
and objects that were negotiated with the partner, but
instead messages and objects that can be used in the
negotiation. That allows the USB PD devices to be shared and
reconfigured. The ports can decide which objects are to be
advertised to the partner before the contract is negotiated.
It is also possible to allow the user space to make that
decision if needed.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220502132058.86236-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In some cases the port of an hub needs to be disabled or switched off
and on again. E.g. when the connected device needs to be re-enumerated.
Or it needs to be explicitly disabled while the rest of the usb tree
stays working.
For this purpose this patch adds an sysfs switch to enable/disable the
port on any hub. In the case the hub is supporting power switching, the
power line will be disabled to the connected device.
When the port gets disabled, the associated device gets disconnected and
removed from the logical usb tree. No further device will be enumerated
on that port until the port gets enabled again.
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220607114522.3359148-1-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
