Here is a single 8250 Kconfig fix for 5.15-rc6 that resolves a
regression that showed up in 5.15-rc1. It has been in linux-next for a
while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYWv0Mg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykeJgCfT8mYR7xo2iTzFRqfvarzH1hvIIgAn3HGUFNf
K3cV5OyOc9lZnGKYhYE6
=SMH1
-----END PGP SIGNATURE-----
Merge tag 'tty-5.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull serial driver fix from Greg KH:
"Here is a single 8250 Kconfig fix for 5.15-rc6 that resolves a
regression that showed up in 5.15-rc1. It has been in linux-next for a
while with no reported issues"
* tag 'tty-5.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: 8250: allow disabling of Freescale 16550 compile test
Up to now sc16is7xx_remove() returns zero unconditionally. Make it
return void instead which makes it easier to see in the callers that
there is no error to handle.
Also the return value of spi remove callbacks is ignored anyway.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20211012153945.2651412-19-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Up to now max310x_remove() returns zero unconditionally. Make it return
void instead which makes it easier to see in the callers that there is
no error to handle.
Also the return value of spi remove callbacks is ignored anyway.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20211012153945.2651412-18-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a call to the custom ->set_termios() which has implementation about
changing the state of RTS and CTS.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Aman Kumar <aman.kumar@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211005133026.21488-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some of the code currently used in dw8250_set_termios(), byt_set_termios()
may be reused by other methods in the future. Extract it to a common helper
function.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211005133026.21488-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In couple of places we may re-use temporary variable instead of
dereferencing it. No functional changes intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211005134529.23256-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ACPI_PTR() is more harmful than helpful. For example, in this case
if CONFIG_ACPI=n, the ID table left unused which is not what we want.
Instead of adding ifdeffery here and there, drop ACPI_PTR().
Fixes: 6a7320c4669f ("serial: 8250_dw: Add ACPI 5.0 support")
Reported-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211005134516.23218-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having "_USI" suffix in EXYNOS_COMMON_SERIAL_DRV_DATA_USI() macro is
confusing. Rename it to just EXYNOS_COMMON_SERIAL_DRV_DATA() and provide
USI registers availability for all Exynos variants instead. While at it,
also convert .has_usi field type to bool, so its usage is more obvious.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20211005095800.2165-1-semen.protsenko@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCYWBSIwAKCRCAXGG7T9hj
vrXxAP9na1EqRJ+SpWyvxHY1jMaIrbg1bgnOc+GsnWxU5liW5AEA4h1HjHtVtrzL
3vweIS6u2fanrWlYML/daQ3r6EuLPQc=
=iXsP
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.15b-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- fix two minor issues in the Xen privcmd driver plus a cleanup patch
for that driver
- fix multiple issues related to running as PVH guest and some related
earlyprintk fixes for other Xen guest types
- fix an issue introduced in 5.15 the Xen balloon driver
* tag 'for-linus-5.15b-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/balloon: fix cancelled balloon action
xen/x86: adjust data placement
x86/PVH: adjust function/data placement
xen/x86: hook up xen_banner() also for PVH
xen/x86: generalize preferred console model from PV to PVH Dom0
xen/x86: make "earlyprintk=xen" work for HVM/PVH DomU
xen/x86: allow "earlyprintk=xen" to work for PV Dom0
xen/x86: make "earlyprintk=xen" work better for PVH Dom0
xen/x86: allow PVH Dom0 without XEN_PV=y
xen/x86: prevent PVH type from getting clobbered
xen/privcmd: drop "pages" parameter from xen_remap_pfn()
xen/privcmd: fix error handling in mmap-resource processing
xen/privcmd: replace kcalloc() by kvcalloc() when allocating empty pages
This reverts commit 32262e2e429cdb31f9e957e997d53458762931b7.
The commit in question claims to determine the inverse of
serial8250_get_divisor() but failed to notice that some drivers override
the default implementation using a get_divisor() callback.
This means that the computed line-speed values can be completely wrong
and results in regular TCSETS requests failing (the incorrect values
would also be passed to any overridden set_divisor() callback).
Similarly, it also failed to honour the old (deprecated) ASYNC_SPD_FLAGS
and would break applications relying on those when re-encoding the
actual line speed.
There are also at least two quirks, UART_BUG_QUOT and an OMAP1510
workaround, which were happily ignored and that are now broken.
Finally, even if the offending commit were to be implemented correctly,
this is a new feature and not something which should be backported to
stable.
Cc: Pali Rohár <pali@kernel.org>
Fixes: 32262e2e429c ("serial: 8250: Fix reporting real baudrate value in c_ospeed field")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211007133146.28949-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SERIAL_8250_FSL option is used to enable a workaround for a
break-detection erratum for Freescale 16550 UARTs in the 8250 driver and
is currently also used to enable support for ACPI enumeration.
It is enabled on PPC, ARM and ARM64 whenever 8250 console support is
enabled (since the quirk is needed for sysrq handling).
Commit b1442c55ce89 ("serial: 8250: extend compile-test coverage")
enabled compile testing of the code in question but did not provide a
means to disable the option when COMPILE_TEST is enabled.
Add a conditional input prompt instead so that SERIAL_8250_FSL is no
longer enabled by default when compile testing while continuing to
always enable the quirk for platforms that may need it.
Fixes: b1442c55ce89 ("serial: 8250: extend compile-test coverage")
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210924141232.4419-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In most cases it is not possible to set exact baudrate value to hardware.
So fix reporting real baudrate value which was set to hardware via c_ospeed
termios field. It can be retrieved by ioctl(TCGETS2) from userspace.
Real baudrate value is calculated from chosen hardware divisor and base
clock. It is implemented in a new function serial8250_compute_baud_rate()
which is inverse of serial8250_get_divisor() function.
With this change is fixed also UART timeout value (it is updated via
uart_update_timeout() function), which is calculated from the now fixed
baudrate value too.
Cc: stable@vger.kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20210927093704.19768-1-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit edc6afc54968 ("tty: switch to ktermios and new framework")
termios speed is no longer stored only in c_cflag member but also in new
additional c_ispeed and c_ospeed members. If BOTHER flag is set in c_cflag
then termios speed is stored only in these new members.
Therefore to correctly restore termios speed it is required to store also
ispeed and ospeed members, not only cflag member.
In case only cflag member with BOTHER flag is restored then functions
tty_termios_baud_rate() and tty_termios_input_baud_rate() returns baudrate
stored in c_ospeed / c_ispeed member, which is zero as it was not restored
too. If reported baudrate is invalid (e.g. zero) then serial core functions
report fallback baudrate value 9600. So it means that in this case original
baudrate is lost and kernel changes it to value 9600.
Simple reproducer of this issue is to boot kernel with following command
line argument: "console=ttyXXX,86400" (where ttyXXX is the device name).
For speed 86400 there is no Bnnn constant and therefore kernel has to
represent this speed via BOTHER c_cflag. Which means that speed is stored
only in c_ospeed and c_ispeed members, not in c_cflag anymore.
If bootloader correctly configures serial device to speed 86400 then kernel
prints boot log to early console at speed speed 86400 without any issue.
But after kernel starts initializing real console device ttyXXX then speed
is changed to fallback value 9600 because information about speed was lost.
This patch fixes above issue by storing and restoring also ispeed and
ospeed members, which are required for BOTHER flag.
Fixes: edc6afc54968 ("[PATCH] tty: switch to ktermios and new framework")
Cc: stable@vger.kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20211002130900.9518-1-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function tty_termios_input_baud_rate() checks IBSHIFT & CBAUD against B0
constant to determinate if input speed equals to output speed. So do same
B0 check also in tty_termios_encode_baud_rate() function to make these two
functions compatible.
Currently macro B0 is defined to 0 so there is no functional change.
This change just make code more explicit to show that Bnnn constants are
stored in CBAUD.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20210927133516.8671-1-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clean up the assignment of sifive_serial_console_ports[ssp->port.line],
this is a pointer to a struct sifive_serial_port so the assignment
should be a NULL rather than a integer 0.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210925224726.183360-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We force the FCR contents on many places in the code instead of writing
what was actually set in mxser_change_speed() (by ->activate() or
->set_serial_info()).
So introduce mxser_port::FCR to hold the proper contents and bitwise-OR
the value to what needs to be set on all those locations. That is,
clearing RX and/or TX FIFOs. Those flags are self-clearing, so no need
to set them to mxser_port::FCR.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210922075938.31390-7-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UART_FCR register is write-only. When reading it, one gets contents
of (read-only) UART_IIR instead as they are shared. This mistake was
performed in mxser_flush_buffer() to clear FIFOs.
Actually FCR handling throughout the driver is completely broken. On
many places, it respects neither mu860 settings, nor FIFO (16450 vs
16550) setting. This patch doesn't help to fix this, it actually does
the same. We will introduce a mxser_port::FCR in the next patch to fix
this issue.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210922075938.31390-6-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This code is used on two places, make a helper for disabling and
clearing FIFOs. And demangle the too complicated 'if' by using a local
variable.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210922075938.31390-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Provided FIFO is always enabled for MUST chips, move its FCR setting out
of PORT_8250/PORT_16450 special case in mxser_change_speed(). Now, we
can pre-set fcr to zero and invert the condition of the 'if'.
This makes the code more readable (no functional change intended).
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210922075938.31390-4-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's used only as a yes-no variable, so make it a bool and switch the
set values appropriately.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210922075938.31390-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mxser_receive_chars_old() is used whenever MOXA_MUST_LSR_RERR is set in
status no matter the HW ID (the last 'if'). So there is no need for
another check of MOXA_MUST_LSR_RERR _with_ hwid == MOXA_MUST_MU860_HWID
(the third 'if'). Hence remove this subcase. That allows us to check
status on a single line with both UART_LSR_BRK_ERROR_BITS (from the
second 'if') and MOXA_MUST_LSR_RERR (the last 'if').
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210922075938.31390-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a user tries to set a too high rate, it fails due to check in
mxser_set_baud(). But the high rate remains set in termios, so the user
might think everything went smooth. Restore the baud rate from the
old_termios if this happens, so that user knows nothing was changed in
fact.
It used to behave the correct way many years ago, but somehow the
restoration vanished with commit 1c45607ad3eb (Char: mxser, remove it)
-- the commit removed mxser's older clone.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210922075938.31390-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We currently have gsmld_output() ignore the return value from device
write. This means we will lose packets if device write returns 0 or
an error.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210930060624.46523-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These two lines need to be indented one more tab.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20211004104343.GF25015@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xenboot_write_console() is dealing with these quite fine so I don't see
why xenboot_console_setup() would return -ENOENT in this case.
Adjust documentation accordingly.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/3d212583-700e-8b2d-727a-845ef33ac265@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
The xen_hvm_early_write() path better wouldn't be taken in this case;
while port 0xE9 can be used, the hypercall path is quite a bit more
efficient. Put that first, as it may also work for DomU-s (see also
xen_raw_console_write()).
While there also bail from the function when the first
domU_write_console() failed - later ones aren't going to succeed.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/4fd89dcb-cfc5-c740-2e94-bb271e432d3e@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
After the previous patch, there are no users of 'file' in
n_tty_ioctl_helper. So remove it also from there.
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210914091134.17426-6-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The only user of 'file' parameter in tty_mode_ioctl is a BUG_ON check.
Provided it never crashed for anyone, it's an overkill to pass the
parameter to tty_mode_ioctl only for this check.
If we wanted to check 'file' there, we should handle it in more graceful
way anyway. Not by a BUG == crash.
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Andreas Koensgen <ajk@comnets.uni-bremen.de>
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210914091134.17426-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The last user was apparently removed by commit a352def21a64 (tty: Ldisc
revamp) in 2008. So remove the field completely, the only setter
(n_tty_inherit_ops) and also its only possible value
(LDISC_FLAG_DEFINED).
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210914091134.17426-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Initially, tty_ldisc_release() was exported for speakup (spk_tty) while
in staging. Later, the call to this function was removed as it was bogus
anyway.
Remove the export now.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210914091134.17426-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Emma Mobile integrated serial port hardware is only present on Emma
Mobile SoCs. Hence add a dependency on ARCH_RENESAS, to prevent asking
the user about this driver when configuring a kernel without Renesas
ARM32 SoC support.
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/7b5a4bbf2f47b2c4c127817e8b1524a650795d97.1631710085.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Initially, tty_ldisc_release() was exported for speakup (spk_tty) while
in staging. Later, the call to this function was removed as it was bogus
anyway.
Remove the export now.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210914091134.17426-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need for existence of a separate header for Moxa's Intellio
cards. Merge it into moxa.c to clean up the tty dir a bit.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210914090823.17206-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'set_signals()' in synclink_gt.c conflicts with an exported symbol
in arch/um/, so change set_signals() to set_gtsignals(). Keep
the function names similar by also changing get_signals() to
get_gtsignals().
../drivers/tty/synclink_gt.c:442:13: error: conflicting types for ‘set_signals’
static void set_signals(struct slgt_info *info);
^~~~~~~~~~~
In file included from ../include/linux/irqflags.h:16:0,
from ../include/linux/spinlock.h:58,
from ../include/linux/mm_types.h:9,
from ../include/linux/buildid.h:5,
from ../include/linux/module.h:14,
from ../drivers/tty/synclink_gt.c:46:
../arch/um/include/asm/irqflags.h:6:5: note: previous declaration of ‘set_signals’ was here
int set_signals(int enable);
^~~~~~~~~~~
Fixes: 705b6c7b34f2 ("[PATCH] new driver synclink_gt")
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20210902003806.17054-1-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As requester,because n_gsm has no uevent report for application,the
application can't know dlci connect or disconnect.
The application will control every dlcl dev by uevent,when application
receive gsmtty0 dev remove uevent,it will close mux function,and change to
normal mode.
Example:
Before modify:
gsmld receive DLC0 DISC,no event report to application
gsmld receive DLC1 SABM,no event report to application
gsmld receive DLC1 DISC,no event report to application
After modify:
Receive DLC0 DISC,report "/devices/virtual/tty/gsmtty0" remove uevent
Receive DLC1 SABM,report "/devices/virtual/tty/gsmtty1" add uevent
Receive DLC1 DISC,report "/devices/virtual/tty/gsmtty1" remove uevent
Signed-off-by: Zhenguo Zhao <Zhenguo.Zhao1@unisoc.com>
Link: https://lore.kernel.org/r/1629461872-26965-7-git-send-email-zhenguo6858@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When n_gsm config "initiator=0",when gsmld config ,as requester ,it
doesn't need to send CLD frame data or SABM frame.
Example,when tty dev receive "AT+CMUX=0",it will change ldisc
n_tty to n_gsm,during config requester,gsmld output "7e 01 ef c3 aa 7e",
initiator maybe not want to receive the frame data.
[ 154.666457] c1 Q> 0) R: UIH(F)
[ 154.669514] c1 C3
[ 154.671519] c1 gsmld_output: 00000000: 7e 01 ef c3 aa 7e
[ 155.014874] c1 Q> 0) R: UIH(F)
[ 155.018000] c1 C3
[ 155.020046] c1 gsmld_output: 00000000: 7e 01 ef c3 aa 7e
[ 155.364425] c1 Q> 0) R: UIH(F)
[ 155.367546] c1 C3
[ 155.369597] c1 gsmld_output: 00000000: 7e 01 ef c3 aa 7e
Signed-off-by: Zhenguo Zhao <Zhenguo.Zhao1@unisoc.com>
Link: https://lore.kernel.org/r/1629461872-26965-5-git-send-email-zhenguo6858@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver's tx_empty callback should signal when the transmit shift register
is empty. So when the last character has been sent.
STAT_TX_FIFO_EMP bit signals only that HW transmit FIFO is empty, which
happens when the last byte is loaded into transmit shift register.
STAT_TX_EMP bit signals when the both HW transmit FIFO and transmit shift
register are empty.
So replace STAT_TX_FIFO_EMP check by STAT_TX_EMP in mvebu_uart_tx_empty()
callback function.
Fixes: 30530791a7a0 ("serial: mvebu-uart: initial support for Armada-3700 serial port")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20210911132017.25505-1-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
