Add documentation on:
- measurement of phase of signal between pin and dpll
- adjustment of pin signal phase
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the hardware reduces the power to the minimum possible, the power
floor is notified via an interrupt.
This can happen when user space requests a power limit via powercap RAPL
interface, which forces the system to enter to the lowest power. This
power floor indication can be used as a hint to resort to other methods
of reducing power than via RAPL power limit.
Before power floor status can be read or the firmware can trigger
notifications regarding it, it needs to be configured via a mailbox
command. The actual power floor status is read via bit 39 of MMIO
offset 0x5B18 of the processor thermal PCI device.
To show the current power floor status and get notification
on a sysfs attribute, add 2 new attributes to
/sys/bus/pci/devices/0000\:00\:04.0/power_limits/
power_floor_enable : This attribute is present when power floor
notifications are supported. This attribute allows to enable/disable
power floor notifications.
power_floor_status : This attribute is present when power floor
notifications are supported. When enabled via power_floor_enable, this
attribute shows the current power floor status.
The power floor implementation provides interfaces which are called
from the sysfs callbacks to enable/disable and read power floor
status. It also provides two additional interfaces to check if the
current processor thermal device interrupt is for power floor status
and to send notifications to user space.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Changelog and documentation changes edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Correct the wrong spelling of 'exposes' in the binner section.
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
There were many changes to PCI core in scope of managed resources APIs.
Update documentation to list the current state of affairs.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/20231006150634.3444251-1-andriy.shevchenko@linux.intel.com
Most low-level PWM drivers support duty_cycle == period, and so does the
sysfs API. Also polarity can be changed for enabled PWMs since commit
39100ceea79f ("pwm: Switch to the atomic API").
Reported-by: Jens Gehrlein <J.Gehrlein@eckelmann.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/20230911154454.675057-1-u.kleine-koenig@pengutronix.de
The MIPI I3C spec refers to a Provisioned ID, since it is (sometimes)
provisioned at device manufacturing.
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20231003075339.197099-1-matt@codeconstruct.com.au
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Split camera sensor documentation into user and kernel portions. This
should make it easier for the user space developers to find the relevant
documentation.
Also add a list of exemplary drivers and add imx219 driver to it, besides
those that were already mentioned.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Optional GPIOLIB as in not depended on or selected by a driver
should NOT use any *_optional() calls, this becomes paradoxical.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
DPLL_CMD_PIN_GET netlink command output for mux-type pins looks ugly
with normal paragraph formatting. Format it as a code block instead.
Signed-off-by: Bagas Sanjaya <bagasdotme@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://lore.kernel.org/r/20230928052708.44820-3-bagasdotme@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
tty_kref_get() is already included in Documentation, but is not properly
formatted. Fix this.
tty_get_baud_rate() is neither properly formatted, nor is included. Fix
both.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230919085156.1578-10-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ioctl helpers are well documented, except they are not plugged in
the Documentation. So fix up the minor issues in the kernel-doc and plug
it in.
The minor issues include:
* bad \t on every line (sphinx misinterprets the description otherwise)
* missing colon after Return
* superfluous \n after the comment
* make some struct members and constants a hyperlink
* and so on
Perhaps better to use --word-diff if one wants to see the "real"
changes.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230919085156.1578-9-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The last driver that still used this old framework has been converted
to the videobuf2 framework. So it is now time to delete the old videobuf
code.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Camera sensor drivers are highly subject to cargo cult programming, with
back practices being copied from old to new drivers. In particular, many
drivers implement system and runtime PM incorrectly. As a first step
towards fixing this situation, refactor and expand the power management
documentation to detail correct usage of system and runtime PM.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Move the power management section up, just after clocks, as it relates
to internal system resources and not features exposed to applications.
The text itself is otherwise unchanged.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The Documentation/devicetree/bindings/clock/clock-bindings.txt file is
deprecated and points to clock-bindings.yaml, which is not hosted in the
kernel source tree. Use an HTTPS link to refer to the YAML binding
document.
While at it, drop "currently" from the paragraph, as the whole file
refers to the current recommended practices except where explicitly
noted.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Drop an unneeded double colon, and use 'shall' instead of 'must' for
consistency with the rest of the file.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
CCS tools is a useful set of programs and libraries for working with CCS
static data. Do mention that in context of the CCS driver.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
drm-misc-next for v6.7-rc1:
UAPI Changes:
- Nouveau changed to not set NO_PREFETCH flag explicitly.
Cross-subsystem Changes:
- Update documentation of dma-buf intro and uapi.
- fbdev/sbus fixes.
- Use initializer macros in a lot of fbdev drivers.
- Add Boris Brezillon as Panfrost driver maintainer.
- Add Jessica Zhang as drm/panel reviewer.
- Make more fbdev drivers use fb_ops helpers for deferred io.
- Small hid trailing whitespace fix.
- Use fb_ops in hid/picolcd
Core Changes:
- Assorted small fixes to ttm tests, drm/mst.
- Documentation updates to bridge.
- Add kunit tests for some drm_fb functions.
- Rework drm_debugfs implementation.
- Update xe documentation to mark todos as completed.
Driver Changes:
- Add support to rockchip for rv1126 mipi-dsi and vop.
- Assorted small fixes to nouveau, bridge/samsung-dsim,
bridge/lvds-codec, loongson, rockchip, panfrost, gma500, repaper,
komeda, virtio, ssd130x.
- Add support for simple panels Mitsubishi AA084XE01,
JDI LPM102A188A,
- Documentation updates to accel/ivpu.
- Some nouveau scheduling/fence fixes.
- Power management related fixes and other fixes to ivpu.
- Assorted bridge/it66121 fixes.
- Make platform drivers return void in remove() callback.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/3da6554b-3b47-fe7d-c4ea-21f4f819dbb6@linux.intel.com
Add documentation explaining common netlink interface to configure DPLL
devices and monitoring events. Common way to implement DPLL device in
a driver is also covered.
Co-developed-by: Bagas Sanjaya <bagasdotme@gmail.com>
Signed-off-by: Bagas Sanjaya <bagasdotme@gmail.com>
Signed-off-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to Meteor Lake processor generation, user space can pass workload
type request to the firmware. Then firmware can optimize power based on
the indicated workload type. User space also uses workload type requests
to implement its own heuristics.
The firmware in Meteor Lake processor generation is capable of predicting
workload type without software help.
To avoid duplicate processing, add a sysfs interface allowing user space
to obtain the workload hint from the firmware instead of trying to
predict the workload type by itself.
This workload hint is passed from the firmware via MMIO offset 0x5B18 of
the processor thermal PCI device. Before workload hints can be produced by
the firmware, it needs to be configured via a mailbox command. This
mailbox command turns ON the workload hint and it allows to program a
notification delay to control the rate of notifications.
The notification delay can be changed from user space vis sysfs.
Attribute group 'workload_hint' in sysfs is used for implementing the
workload hints interface between user space and the kernel.
It contains the following attributes:
workload_type_enable:
Enables/disables workload type hints from the firmware.
notification_delay_ms:
Notification delay in milliseconds.
workload_type_index:
The current workload type index predicted by the firmware (see
the documentation changes below for supported index values and
their meaning).
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Changelog edits, documentation edits, whitespace adjustments ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Fix OF include file for ata platform drivers (Rob).
- Simplify various ahci, sata and pata platform drivers using the
function devm_platform_ioremap_resource() (Yangtao).
- Cleanup libata time related argument types (e.g. timeouts values)
(Sergey).
- Cleanup libata code around error handling as all ata drivers now
define a error_handler operation (Hannes and Niklas).
- Remove functions intended for libsas that are in fact unused
(Niklas).
- Change the remove device callback of platform drivers to a null
function (Uwe).
- Simplify the pata_imx driver using devm_clk_get_enabled() (Li).
- Remove old and uinused remnants of the ide code in arm, parisc,
powerpc, sparc and m68k architectures and associated drivers
(pata_buddha, pata_falcon and pata_gayle) (Geert).
- Add missing MODULE_DESCRIPTION() in the sata_gemini and pata_ftide010
drivers (me).
- Several fixes for the pata_ep93xx and pata_falcon drivers (Nikita,
Michael).
- Add Elkhart Lake AHCI controller support to the ahci driver (Werner).
- Disable NCQ trim on Micron 1100 drives (Pawel).
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQSRPv8tYSvhwAzJdzjdoc3SxdoYdgUCZPbUdQAKCRDdoc3SxdoY
du6NAP9G10EhjgXDNIM8f1AN8gHrZk2RGSxSuqIKKROxl2i+ugD+Mt8/UjRpf0JO
nVdKTfgeXaLfCXHN/fmkIYNmk+I7Twg=
=9Ety
-----END PGP SIGNATURE-----
Merge tag 'ata-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata
Pull ata updates from Damien Le Moal:
- Fix OF include file for ata platform drivers (Rob)
- Simplify various ahci, sata and pata platform drivers using the
function devm_platform_ioremap_resource() (Yangtao)
- Cleanup libata time related argument types (e.g. timeouts values)
(Sergey)
- Cleanup libata code around error handling as all ata drivers now
define a error_handler operation (Hannes and Niklas)
- Remove functions intended for libsas that are in fact unused (Niklas)
- Change the remove device callback of platform drivers to a null
function (Uwe)
- Simplify the pata_imx driver using devm_clk_get_enabled() (Li)
- Remove old and uinused remnants of the ide code in arm, parisc,
powerpc, sparc and m68k architectures and associated drivers
(pata_buddha, pata_falcon and pata_gayle) (Geert)
- Add missing MODULE_DESCRIPTION() in the sata_gemini and pata_ftide010
drivers (me)
- Several fixes for the pata_ep93xx and pata_falcon drivers (Nikita,
Michael)
- Add Elkhart Lake AHCI controller support to the ahci driver (Werner)
- Disable NCQ trim on Micron 1100 drives (Pawel)
* tag 'ata-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata: (60 commits)
ata: libata-core: Disable NCQ_TRIM on Micron 1100 drives
ata: ahci: Add Elkhart Lake AHCI controller
ata: pata_falcon: add data_swab option to byte-swap disk data
ata: pata_falcon: fix IO base selection for Q40
ata: pata_ep93xx: use soc_device_match for UDMA modes
ata: pata_ep93xx: fix error return code in probe
ata: sata_gemini: Add missing MODULE_DESCRIPTION
ata: pata_ftide010: Add missing MODULE_DESCRIPTION
m68k: Remove <asm/ide.h>
ata: pata_gayle: Remove #include <asm/ide.h>
ata: pata_falcon: Remove #include <asm/ide.h>
ata: pata_buddha: Remove #include <asm/ide.h>
asm-generic: Remove ide_iops.h
sparc: Remove <asm/ide.h>
powerpc: Remove <asm/ide.h>
parisc: Remove <asm/ide.h>
ARM: Remove <asm/ide.h>
ata: pata_imx: Use helper function devm_clk_get_enabled()
ata: sata_rcar: Convert to platform remove callback returning void
ata: sata_mv: Convert to platform remove callback returning void
...
-----BEGIN PGP SIGNATURE-----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=yuz5
-----END PGP SIGNATURE-----
Merge tag 'media/v6.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new i2c drivers: ds90ub913, ds90ub953, ds90ub960, dw9719, ds90ub913
- new Intel IVSC MEI drivers
- some Mediatek platform drivers were moved to a common location
- Intel atomisp2 driver is now working with the main ov2680 driver. Due
to that, the atomisp2 ov2680 staging one was removed
- the bttv driver was finally converted to videobuf2 framework. This
was the last one upstream using videobuf version 1 core. We'll likely
remove the old videobuf framework on 6.7
- lots of improvements at atomisp driver: it now works with normal I2C
sensors. Several compile-mode dependecies to select between ISP2400
and ISP2401 are now solved in runtime
- a new ipu-bridge logic was added to work with IVSC MEI drivers
- venus driver gained better support for new VPU versions
- the v4l core async framework has gained lots of improvements and
cleanups
- lots of other cleanups, improvements and driver fixes
* tag 'media/v6.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (358 commits)
media: ivsc: Add ACPI dependency
media: bttv: convert to vb2
media: bttv: use audio defaults for winfast2000
media: bttv: refactor bttv_set_dma()
media: bttv: move vbi_skip/vbi_count out of buffer
media: bttv: remove crop info from bttv_buffer
media: bttv: remove tvnorm field from bttv_buffer
media: bttv: remove format field from bttv_buffer
media: bttv: move do_crop flag out of bttv_fh
media: bttv: copy vbi_fmt from bttv_fh
media: bttv: copy vid fmt/width/height from fh
media: bttv: radio use v4l2_fh instead of bttv_fh
media: bttv: replace BUG with WARN_ON
media: bttv: use video_drvdata to get bttv
media: i2c: rdacm21: Fix uninitialized value
media: coda: Remove duplicated include
media: vivid: fix the racy dev->radio_tx_rds_owner
media: i2c: ccs: Check rules is non-NULL
media: i2c: ds90ub960: Fix PLL config for 1200 MHz CSI rate
media: i2c: ds90ub953: Fix use of uninitialized variables
...
Here is the big set of char/misc and other small driver subsystem
changes for 6.6-rc1.
Stuff all over the place here, lots of driver updates and changes and
new additions. Short summary is:
- new IIO drivers and updates
- Interconnect driver updates
- fpga driver updates and additions
- fsi driver updates
- mei driver updates
- coresight driver updates
- nvmem driver updates
- counter driver updates
- lots of smaller misc and char driver updates and additions
All of these have been in linux-next for a long time with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZPH64g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynr2QCfd3RKeR+WnGzyEOFhksl30UJJhiIAoNZtYT5+
t9KG0iMDXRuTsOqeEQbd
=tVnk
-----END PGP SIGNATURE-----
Merge tag 'char-misc-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of char/misc and other small driver subsystem
changes for 6.6-rc1.
Stuff all over the place here, lots of driver updates and changes and
new additions. Short summary is:
- new IIO drivers and updates
- Interconnect driver updates
- fpga driver updates and additions
- fsi driver updates
- mei driver updates
- coresight driver updates
- nvmem driver updates
- counter driver updates
- lots of smaller misc and char driver updates and additions
All of these have been in linux-next for a long time with no reported
problems"
* tag 'char-misc-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (267 commits)
nvmem: core: Notify when a new layout is registered
nvmem: core: Do not open-code existing functions
nvmem: core: Return NULL when no nvmem layout is found
nvmem: core: Create all cells before adding the nvmem device
nvmem: u-boot-env:: Replace zero-length array with DECLARE_FLEX_ARRAY() helper
nvmem: sec-qfprom: Add Qualcomm secure QFPROM support
dt-bindings: nvmem: sec-qfprom: Add bindings for secure qfprom
dt-bindings: nvmem: Add compatible for QCM2290
nvmem: Kconfig: Fix typo "drive" -> "driver"
nvmem: Explicitly include correct DT includes
nvmem: add new NXP QorIQ eFuse driver
dt-bindings: nvmem: Add t1023-sfp efuse support
dt-bindings: nvmem: qfprom: Add compatible for MSM8226
nvmem: uniphier: Use devm_platform_get_and_ioremap_resource()
nvmem: qfprom: do some cleanup
nvmem: stm32-romem: Use devm_platform_get_and_ioremap_resource()
nvmem: rockchip-efuse: Use devm_platform_get_and_ioremap_resource()
nvmem: meson-mx-efuse: Convert to devm_platform_ioremap_resource()
nvmem: lpc18xx_otp: Convert to devm_platform_ioremap_resource()
nvmem: brcm_nvram: Use devm_platform_get_and_ioremap_resource()
...
Here is the big set of tty and serial driver changes for 6.6-rc1.
Lots of cleanups in here this cycle, and some driver updates. Short
summary is:
- Jiri's continued work to make the tty code and apis be a bit more
sane with regards to modern kernel coding style and types
- cpm_uart driver updates
- n_gsm updates and fixes
- meson driver updates
- sc16is7xx driver updates
- 8250 driver updates for different hardware types
- qcom-geni driver fixes
- tegra serial driver change
- stm32 driver updates
- synclink_gt driver cleanups
- tty structure size reduction
All of these have been in linux-next this week with no reported issues.
The last bit of cleanups from Jiri and the tty structure size reduction
came in last week, a bit late but as they were just style changes and
size reductions, I figured they should get into this merge cycle so that
others can work on top of them with no merge conflicts.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZPH+jA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykKyACgldt6QeenTN+6dXIHS/eQHtTKZwMAn3arSeXI
QrUUnLFjOWyoX87tbMBQ
=LVw0
-----END PGP SIGNATURE-----
Merge tag 'tty-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big set of tty and serial driver changes for 6.6-rc1.
Lots of cleanups in here this cycle, and some driver updates. Short
summary is:
- Jiri's continued work to make the tty code and apis be a bit more
sane with regards to modern kernel coding style and types
- cpm_uart driver updates
- n_gsm updates and fixes
- meson driver updates
- sc16is7xx driver updates
- 8250 driver updates for different hardware types
- qcom-geni driver fixes
- tegra serial driver change
- stm32 driver updates
- synclink_gt driver cleanups
- tty structure size reduction
All of these have been in linux-next this week with no reported
issues. The last bit of cleanups from Jiri and the tty structure size
reduction came in last week, a bit late but as they were just style
changes and size reductions, I figured they should get into this merge
cycle so that others can work on top of them with no merge conflicts"
* tag 'tty-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (199 commits)
tty: shrink the size of struct tty_struct by 40 bytes
tty: n_tty: deduplicate copy code in n_tty_receive_buf_real_raw()
tty: n_tty: extract ECHO_OP processing to a separate function
tty: n_tty: unify counts to size_t
tty: n_tty: use u8 for chars and flags
tty: n_tty: simplify chars_in_buffer()
tty: n_tty: remove unsigned char casts from character constants
tty: n_tty: move newline handling to a separate function
tty: n_tty: move canon handling to a separate function
tty: n_tty: use MASK() for masking out size bits
tty: n_tty: make n_tty_data::num_overrun unsigned
tty: n_tty: use time_is_before_jiffies() in n_tty_receive_overrun()
tty: n_tty: use 'num' for writes' counts
tty: n_tty: use output character directly
tty: n_tty: make flow of n_tty_receive_buf_common() a bool
Revert "tty: serial: meson: Add a earlycon for the T7 SoC"
Documentation: devices.txt: Fix minors for ttyCPM*
Documentation: devices.txt: Remove ttySIOC*
Documentation: devices.txt: Remove ttyIOC*
serial: 8250_bcm7271: improve bcm7271 8250 port
...
Here is the big set of USB, Thunderbolt, and PHY driver updates for
6.6-rc1. Included in here are:
- PHY driver additions and cleanups
- Thunderbolt minor additions and fixes
- USB MIDI 2 gadget support added
- dwc3 driver updates and additions
- Removal of some old USB wireless code that was missed when that
codebase was originally removed a few years ago, cleaning up some
core USB code paths
- USB core potential use-after-free fixes that syzbot from different
people/groups keeps tripping over
- typec updates and additions
- gadget fixes and cleanups
- loads of smaller USB core and driver cleanups all over the place
Full details are in the shortlog. All of these have been in linux-next
for a while with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZPIAOQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yn80gCgybzMp0YnSildFetSC8lUJTnzjQcAn3KWzb75
Zt72jxGl4ZOXHEpozG4O
=FLrK
-----END PGP SIGNATURE-----
Merge tag 'usb-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt / PHY driver updates from Greg KH:
"Here is the big set of USB, Thunderbolt, and PHY driver updates for
6.6-rc1. Included in here are:
- PHY driver additions and cleanups
- Thunderbolt minor additions and fixes
- USB MIDI 2 gadget support added
- dwc3 driver updates and additions
- Removal of some old USB wireless code that was missed when that
codebase was originally removed a few years ago, cleaning up some
core USB code paths
- USB core potential use-after-free fixes that syzbot from different
people/groups keeps tripping over
- typec updates and additions
- gadget fixes and cleanups
- loads of smaller USB core and driver cleanups all over the place
Full details are in the shortlog. All of these have been in linux-next
for a while with no reported problems"
* tag 'usb-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (154 commits)
platform/chrome: cros_ec_typec: Configure Retimer cable type
tcpm: Avoid soft reset when partner does not support get_status
usb: typec: tcpm: reset counter when enter into unattached state after try role
usb: typec: tcpm: set initial svdm version based on pd revision
USB: serial: option: add FOXCONN T99W368/T99W373 product
USB: serial: option: add Quectel EM05G variant (0x030e)
usb: dwc2: add pci_device_id driver_data parse support
usb: gadget: remove max support speed info in bind operation
usb: gadget: composite: cleanup function config_ep_by_speed_and_alt()
usb: gadget: config: remove max speed check in usb_assign_descriptors()
usb: gadget: unconditionally allocate hs/ss descriptor in bind operation
usb: gadget: f_uvc: change endpoint allocation in uvc_function_bind()
usb: gadget: add a inline function gether_bitrate()
usb: gadget: use working speed to calcaulate network bitrate and qlen
dt-bindings: usb: samsung,exynos-dwc3: Add Exynos850 support
usb: dwc3: exynos: Add support for Exynos850 variant
usb: gadget: udc-xilinx: fix incorrect type in assignment warning
usb: gadget: udc-xilinx: fix cast from restricted __le16 warning
usb: gadget: udc-xilinx: fix restricted __le16 degrades to integer warning
USB: dwc2: hande irq on dead controller correctly
...
- VFIO direct character device (cdev) interface support. This extracts
the vfio device fd from the container and group model, and is intended
to be the native uAPI for use with IOMMUFD. (Yi Liu)
- Enhancements to the PCI hot reset interface in support of cdev usage.
(Yi Liu)
- Fix a potential race between registering and unregistering vfio files
in the kvm-vfio interface and extend use of a lock to avoid extra
drop and acquires. (Dmitry Torokhov)
- A new vfio-pci variant driver for the AMD/Pensando Distributed Services
Card (PDS) Ethernet device, supporting live migration. (Brett Creeley)
- Cleanups to remove redundant owner setup in cdx and fsl bus drivers,
and simplify driver init/exit in fsl code. (Li Zetao)
- Fix uninitialized hole in data structure and pad capability structures
for alignment. (Stefan Hajnoczi)
-----BEGIN PGP SIGNATURE-----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=eKSR
-----END PGP SIGNATURE-----
Merge tag 'vfio-v6.6-rc1' of https://github.com/awilliam/linux-vfio
Pull VFIO updates from Alex Williamson:
- VFIO direct character device (cdev) interface support. This extracts
the vfio device fd from the container and group model, and is
intended to be the native uAPI for use with IOMMUFD (Yi Liu)
- Enhancements to the PCI hot reset interface in support of cdev usage
(Yi Liu)
- Fix a potential race between registering and unregistering vfio files
in the kvm-vfio interface and extend use of a lock to avoid extra
drop and acquires (Dmitry Torokhov)
- A new vfio-pci variant driver for the AMD/Pensando Distributed
Services Card (PDS) Ethernet device, supporting live migration (Brett
Creeley)
- Cleanups to remove redundant owner setup in cdx and fsl bus drivers,
and simplify driver init/exit in fsl code (Li Zetao)
- Fix uninitialized hole in data structure and pad capability
structures for alignment (Stefan Hajnoczi)
* tag 'vfio-v6.6-rc1' of https://github.com/awilliam/linux-vfio: (53 commits)
vfio/pds: Send type for SUSPEND_STATUS command
vfio/pds: fix return value in pds_vfio_get_lm_file()
pds_core: Fix function header descriptions
vfio: align capability structures
vfio/type1: fix cap_migration information leak
vfio/fsl-mc: Use module_fsl_mc_driver macro to simplify the code
vfio/cdx: Remove redundant initialization owner in vfio_cdx_driver
vfio/pds: Add Kconfig and documentation
vfio/pds: Add support for firmware recovery
vfio/pds: Add support for dirty page tracking
vfio/pds: Add VFIO live migration support
vfio/pds: register with the pds_core PF
pds_core: Require callers of register/unregister to pass PF drvdata
vfio/pds: Initial support for pds VFIO driver
vfio: Commonize combine_ranges for use in other VFIO drivers
kvm/vfio: avoid bouncing the mutex when adding and deleting groups
kvm/vfio: ensure kvg instance stays around in kvm_vfio_group_add()
docs: vfio: Add vfio device cdev description
vfio: Compile vfio_group infrastructure optionally
vfio: Move the IOMMU_CAP_CACHE_COHERENCY check in __vfio_register_dev()
...
- Work from Carlos Bilbao to integrate rustdoc output into the generated
HTML documentation. This took some work to figure out how to do it
without slowing the docs build and without creating people who don't have
Rust installed, but Carlos got there.
- Move the loongarch and mips architecture documentation under
Documentation/arch/.
- Some more maintainer documentation from Jakub
...plus the usual assortment of updates, translations, and fixes.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAmTvqNkPHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5YgIgH/3drfLtlFtzLqDOzrzDXS8yGnE3pPdxw796b
/ZFzAK16wYKaKevYoIz8bVGGKaE1sEUW0mhlq4KGdfZuxLG8YnWS8URyCW4FDU2E
6qNL+8oJ8LZfID46f9Q8ZgfEz7yF/mhCqPk7MEswYtwbscs2ZTGCTGYB/5BHlBuT
LR+M89uLmHgr8S1o24v30OgiX+VvQFyu0xoxIhbiqUZvBd/XdfX2pgYd9BGzMj5q
C2ZP+V14g36c5pV0EO9TwhCXOF/WVrp7DbjbfWAsqBSLxvpXPydH2q1DUzGeQtP1
exujrBD1O8q3pPdaNA5R+h6cWlHmUZug9mE4BRLp9ErGrozwJsQ=
=C3Uv
-----END PGP SIGNATURE-----
Merge tag 'docs-6.6' of git://git.lwn.net/linux
Pull documentation updates from Jonathan Corbet:
"Documentation work keeps chugging along; this includes:
- Work from Carlos Bilbao to integrate rustdoc output into the
generated HTML documentation. This took some work to figure out how
to do it without slowing the docs build and without creating people
who don't have Rust installed, but Carlos got there
- Move the loongarch and mips architecture documentation under
Documentation/arch/
- Some more maintainer documentation from Jakub
... plus the usual assortment of updates, translations, and fixes"
* tag 'docs-6.6' of git://git.lwn.net/linux: (56 commits)
Docu: genericirq.rst: fix irq-example
input: docs: pxrc: remove reference to phoenix-sim
Documentation: serial-console: Fix literal block marker
docs/mm: remove references to hmm_mirror ops and clean typos
docs/zh_CN: correct regi_chg(),regi_add() to region_chg(),region_add()
Documentation: Fix typos
Documentation/ABI: Fix typos
scripts: kernel-doc: fix macro handling in enums
scripts: kernel-doc: parse DEFINE_DMA_UNMAP_[ADDR|LEN]
Documentation: riscv: Update boot image header since EFI stub is supported
Documentation: riscv: Add early boot document
Documentation: arm: Add bootargs to the table of added DT parameters
docs: kernel-parameters: Refer to the correct bitmap function
doc: update params of memhp_default_state=
docs: Add book to process/kernel-docs.rst
docs: sparse: fix invalid link addresses
docs: vfs: clean up after the iterate() removal
docs: Add a section on surveys to the researcher guidelines
docs: move mips under arch
docs: move loongarch under arch
...
We've received a fairly wide range of changes at this time, including
for ALSA and ASoC core, but all of them are rather small changes.
Here are some highlights:
ALSA / ASoC Core:
- Fixes of inconsistent locking around control API helpers
- A few new control API functions and cleanups
- Workarounds for potential UAFs by delayed kobj releases
- Unified PCM copy ops with iov_iter
- Continued efforts for ASoC API cleanups
ASoC:
- An adaptor to allow use of IIO DACs and ADCs in ASoC which pulls in
some IIO changes
- Create a library function for intlog10() and use it in the NAU8825
driver
- Convert drivers to use the more modern maple tree register cache
- Lots of work on the SOF framework, AMD and Intel drivers, including a
lot of cleanup and new device support
- Standardization of the presentation of jacks from drivers
- Provision of some generic sound card DT properties
- Support for AMD Van Gogh, AMD machines with MAX98388 and NAU8821,
AWInic AW88261, Cirrus Logic CS35L36 and CS42L43, various Intel
platforms including AVS machines with ES8336 and RT5663, Mediatek
MT7986, NXP i.MX93, RealTek RT1017 and StarFive JH7110
Others:
- New test coverage including ASoC and topology tests in KUnit;
this also involves enabling UML builds of ALSA since that's the
default KUnit test environment which pulls in the addition of some
stubs to the driver
- More enhancement of pcmtest driver
- A few fixes / enhancements of MIDI 2.0 UMP core
- Using PCI definitions in allover HD-audio code
- Support for Cirrus CS35L56 and TI TAS2781 HD-audio sub-codecs
- CS35L41 HD-audio sub-codec improvements
- Continued emu10k1 improvements
-----BEGIN PGP SIGNATURE-----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=Rr0i
-----END PGP SIGNATURE-----
Merge tag 'sound-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"We've received a fairly wide range of changes at this time, including
for ALSA and ASoC core, but all of them are rather small changes.
Here are some highlights:
ALSA / ASoC Core:
- Fixes of inconsistent locking around control API helpers
- A few new control API functions and cleanups
- Workarounds for potential UAFs by delayed kobj releases
- Unified PCM copy ops with iov_iter
- Continued efforts for ASoC API cleanups
ASoC:
- An adaptor to allow use of IIO DACs and ADCs in ASoC which pulls in
some IIO changes
- Create a library function for intlog10() and use it in the NAU8825
driver
- Convert drivers to use the more modern maple tree register cache
- Lots of work on the SOF framework, AMD and Intel drivers, including
a lot of cleanup and new device support
- Standardization of the presentation of jacks from drivers
- Provision of some generic sound card DT properties
- Support for AMD Van Gogh, AMD machines with MAX98388 and NAU8821,
AWInic AW88261, Cirrus Logic CS35L36 and CS42L43, various Intel
platforms including AVS machines with ES8336 and RT5663, Mediatek
MT7986, NXP i.MX93, RealTek RT1017 and StarFive JH7110
Others:
- New test coverage including ASoC and topology tests in KUnit; this
also involves enabling UML builds of ALSA since that's the default
KUnit test environment which pulls in the addition of some stubs to
the driver
- More enhancement of pcmtest driver
- A few fixes / enhancements of MIDI 2.0 UMP core
- Using PCI definitions in allover HD-audio code
- Support for Cirrus CS35L56 and TI TAS2781 HD-audio sub-codecs
- CS35L41 HD-audio sub-codec improvements
- Continued emu10k1 improvements"
* tag 'sound-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (693 commits)
ALSA: pcm: Fix missing fixup call in compat hw_refine ioctl
ASoC: dwc: i2s: Fix unused functions
ALSA: usb-audio: Don't try to submit URBs after disconnection
ALSA: emu10k1: add separate documentation for E-MU cards
ALSA: emu10k1: more documentation updates
ALSA: emu10k1: de-duplicate audigy-mixer.rst vs. sb-live-mixer.rst
ALSA: ump: Fix -Wformat-truncation warnings
ALSA: hda: Add missing dependency on CONFIG_EFI for Cirrus/TI sub-codecs
ALSA: doc: Fix missing backquote in midi-2.0.rst
ALSA: hda/realtek: Add quirk for mute LEDs on HP ENVY x360 15-eu0xxx
ALSA: hda/tas2781: Switch back to use struct i2c_driver's .probe()
ASoC: soc-core.c: Do not error if a DAI link component is not found
ASoC: codecs: Fix error code in aw88261_i2c_probe()
ASoC: audio-graph-card.c: move audio_graph_parse_of()
ASoC: cs42l43: Use new-style PM runtime macros
ALSA: documentation: Add description for USB MIDI 2.0 gadget driver
ALSA: ump: Don't create unused substreams for static blocks
ALSA: ump: Fill group names for legacy rawmidi substreams
ALSA: usb-audio: Attach legacy rawmidi after probing all UMP EPs
ALSA: ac97: Fix possible error value of *rac97
...
It's often useful during test, debug, and development to issue path
votes from shell. Add a debugfs client for this purpose.
Example usage:
cd /sys/kernel/debug/interconnect/test-client/
# Configure node endpoints for the path from CPU to DDR on
# qcom/sm8550.
echo chm_apps > src_node
echo ebi > dst_node
# Get path between src_node and dst_node. This is only
# necessary after updating the node endpoints.
echo 1 > get
# Set desired BW to 1GBps avg and 2GBps peak.
echo 1000000 > avg_bw
echo 2000000 > peak_bw
# Vote for avg_bw and peak_bw on the latest path from "get".
# Voting for multiple paths is possible by repeating this
# process for different nodes endpoints.
echo 1 > commit
Allowing userspace to directly enable and set bus rates can be dangerous
So, following in the footsteps of the regmap [0] and clk [1] frameworks,
keep these userspace controls compile-time disabled without Kconfig
options to enable them. Enabling this will require code changes to
define INTERCONNECT_ALLOW_WRITE_DEBUGFS.
[0] commit 09c6ecd39410 ("regmap: Add support for writing to regmap registers via debugfs")
[1] commit 37215da5553e ("clk: Add support for setting clk_rate via debugfs")
Signed-off-by: Mike Tipton <quic_mdtipton@quicinc.com>
Link: https://lore.kernel.org/r/20230807142914.12480-4-quic_mdtipton@quicinc.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Use __tty_insert_flip_string_flags() for the slow path of
tty_insert_flip_char(). The former is generic enough, so there is no
reason to reimplement the injection once again.
So now we have a single function stuffing into tty buffers.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230816105530.3335-8-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
They both do the same except for flags. One mem-copies the flags from
the caller, the other mem-sets to one flag given by the caller. This can
be unified with a simple if in the unified function.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230816105530.3335-4-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since there's a lot of confusion around this, document both the rules
and the best practices around negotiating, allocating, importing, and
using buffers when crossing context/process/device/subsystem boundaries.
This ties up all of dma-buf, formats and modifiers, and their usage.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Simon Ser <contact@emersion.fr>
Reviewed-by: Simon Ser <contact@emersion.fr>
Reviewed-by: Sui Jingfeng <suijingfeng@loongson.cn>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20230803154908.105124-4-daniels@collabora.com
The CSI2 specification specifies a standard method to access camera sensor
registers called "Camera Control Interface (CCI)".
This uses either 8 or 16 bit (big-endian wire order) register addresses
and supports 8, 16, 24 or 32 bit (big-endian wire order) register widths.
Currently a lot of Linux camera sensor drivers all have their own custom
helpers for this, often copy and pasted from other drivers.
Add a set of generic helpers for this so that all sensor drivers can
switch to a single common implementation.
These helpers take an extra optional "int *err" function parameter,
this can be used to chain a bunch of register accesses together with
only a single error check at the end, rather than needing to error
check each individual register access. The first failing call will
set the contents of err to a non 0 value and all other calls will
then become no-ops.
Link: https://lore.kernel.org/linux-media/59aefa7f-7bf9-6736-6040-39551329cd0a@redhat.com/
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Tommaso Merciai <tomm.merciai@gmail.com>
Reviewed-by: Tommaso Merciai <tomm.merciai@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Describe the new callbacks and clarify when the adap->lock
mutex is held or not.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Document that sub-device notifiers are now registered using
v4l2_async_subdev_nf_init(). No documentation is changed as it seems that
sub-device notifiers were not documented apart from kernel-doc comments.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de> # imx6qp
Tested-by: Niklas Söderlund <niklas.soderlund@ragnatech.se> # rcar + adv746x
Tested-by: Aishwarya Kothari <aishwarya.kothari@toradex.com> # Apalis i.MX6Q with TC358743
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> # Renesas RZ/G2L SMARC
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Support for Wireless USB and Ultra WideBand was removed in 2020 by
commit caa6772db4c1 ("Staging: remove wusbcore and UWB from the kernel
tree."). But the documentation files were left behind.
Let's get rid of that out-of-date documentation.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/015d4310-bcd3-4ba4-9a0e-3664f281a9be@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all libata drivers have migrated to use the error_handler
callback, remove the deprecated phy_reset and eng_timeout callbacks.
Also remove references to non-existent functions sata_phy_reset and
ata_qc_timeout from Documentation/driver-api/libata.rst.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Remove ata_bus_probe() as it is unused.
Also, remove references to ata_bus_probe and port_disable in
Documentation/driver-api/libata.rst, as neither exist anymore.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Rename v4l2_async_subdev as v4l2_async_connection, in order to
differentiate between the sub-devices and their connections: one
sub-device can have many connections but the V4L2 async framework has so
far allowed just a single one. Connections in this context will later
translate into either MC ancillary or data links.
This patch prepares changing that relation by changing existing users of
v4l2_async_subdev to switch to v4l2_async_connection. Async sub-devices
themselves will not be needed anymore
Additionally, __v4l2_async_nf_add_subdev() has been renamed
__v4l2_async_nf_add_connection().
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de> # imx6qp
Tested-by: Niklas Söderlund <niklas.soderlund@ragnatech.se> # rcar + adv746x
Tested-by: Aishwarya Kothari <aishwarya.kothari@toradex.com> # Apalis i.MX6Q with TC358743
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> # Renesas RZ/G2L SMARC
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Document v4l2_async_nf_cleanup() which must be called before releasing an
unregistered notifier's memory. Also remove the sentence regarding
v4l2_async_nf_init() arguments --- those are documented in kerneldoc which
is referred here.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> # Renesas RZ/G2L SMARC
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Also v4l2_async_nf_add_fwnode() may be used to add an async sub-device
descriptor to a notifier. Document this. Also remove a redundant sentence.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de> # imx6qp
Tested-by: Niklas Söderlund <niklas.soderlund@ragnatech.se> # rcar + adv746x
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Aishwarya Kothari <aishwarya.kothari@toradex.com> # Apalis i.MX6Q with TC358743
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> # Renesas RZ/G2L SMARC
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Document that the notifier of an async sub-device is, besider
unregistered, also cleaned up using v4l2_async_unregister_subdev().
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> # Renesas RZ/G2L SMARC
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add section titles for async documentation. While the documentation is
mostly fine as-is, it has grown from its original state but remains
without internal structure. Add it now.
Also remove an extra newline.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> # Renesas RZ/G2L SMARC
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
An example adding an async sub-device to a V4L2 async notifier. The name
of the variable in error handling was wrong (asd vs. my_asd).
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> # Renesas RZ/G2L SMARC
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This gives notes for userspace applications on device cdev usage.
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Tested-by: Yanting Jiang <yanting.jiang@intel.com>
Signed-off-by: Yi Liu <yi.l.liu@intel.com>
Link: https://lore.kernel.org/r/20230718135551.6592-27-yi.l.liu@intel.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
