The omapdrm driver currently takes a config/module arg to figure out the number
of crtcs it needs to create. We could create as many crtcs as there are overlay
managers in the DSS hardware, but we don't do that because each crtc eats up
one DSS overlay, and that reduces the number of planes we can attach to a single
crtc.
Since the number of crtcs may be lesser than the number of hardware overlay
managers, we need to figure out which overlay managers to use for our crtcs. The
current approach is to use pipe2chan(), which returns a higher numbered manager
for the crtc.
The problem with this approach is that it assumes that the overlay managers we
choose will connect to the encoders the platform's panels are going to use,
this isn't true, an overlay manager connects only to a few outputs/encoders, and
choosing any overlay manager for our crtc might lead to a situation where the
encoder cannot connect to any of the crtcs we have chosen. For example, an
omap5-panda board has just one hdmi output. If num_crtc is set to 1, with the
current approach, pipe2chan will pick up the LCD2 overlay manager, which cannot
connect to the hdmi encoder at all. The only manager that could have connected
to hdmi was the TV overlay manager.
Therefore, there is a need to choose our overlay managers keeping in mind the
panels we have on that platform. The new approach iterates through all the
available panels, creates encoders and connectors for them, and then tries to
get a suitable overlay manager to create a crtc which can connect to the
encoders.
We use the dispc_channel field in omap_dss_output to retrieve the desired
overlay manager's channel number, we then check whether the manager had already
been assigned to a crtc or not. If it was already assigned to a crtc, we assume
that out of all the encoders which intend use this crtc, only one will run at a
time. If the overlay manager wan't assigned to a crtc till then, we create a
new crtc and link it with the overlay manager.
This approach just looks for the best dispc_channel for each encoder. On DSS HW,
some encoders can connect to multiple overlay managers. Since we don't try
looking for alternate overlay managers, there is a greater possibility that 2
or more encoders end up asking for the same crtc, causing only one encoder to
run at a time.
Also, this approach isn't the most optimal one, it can do either good or bad
depending on the sequence in which the panels/outputs are parsed. The optimal
way would be some sort of back tracking approach, where we improve the set of
managers we use as we iterate through the list of panels/encoders. That's
something left for later.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When userspace calls SET_PLANE ioctl, drm core takes a reference of the fb and
passes control to the update_plane op defined by the drm driver.
In omapdrm, we have a worker thread which queues framebuffers objects received
from update_plane and displays them at the appropriate time.
It is possible that the framebuffer is destoryed by userspace between the time
of calling the ioctl and apply-worker being scheduled. If this happens, the
apply-worker holds a pointer to a framebuffer which is already destroyed.
Take an extra refernece/unreference of the fb in omap_plane_update() to prevent
this from happening. A reference is taken of the fb passed to update_plane(),
the previous framebuffer (held by plane->fb) is unreferenced. This will prevent
drm from destroying the framebuffer till the time it's unreferenced by the
apply-worker.
This is in addition to the exisitng reference/unreference in update_pin(),
which is taken for the scanout of the plane's current framebuffer, and an
unreference the previous framebuffer.
Signed-off-by: Archit Taneja <archit@ti.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omapdrm driver requires omapdss panel drivers to expose ops like detect,
set_timings and check_timings. These can be NULL for fixed panel DPI, DBI, DSI
and SDI drivers. At some places, there are no checks to see if the panel driver
has these ops or not, and that leads to a crash.
The following things are done to make fixed panels work:
- The omap_connector's detect function is modified such that it considers panel
types which are generally fixed panels as always connected(provided the panel
driver doesn't have a detect op). Hence, the connector corresponding to these
panels is always in a 'connected' state.
- If a panel driver doesn't have a check_timings op, assume that it supports the
mode passed to omap_connector_mode_valid(the 'mode_valid' drm helper function)
- The function omap_encoder_update shouldn't really do anything for fixed
resolution panels, make sure that it calls set_timings only if the panel
driver has one.
Signed-off-by: Archit Taneja <archit@ti.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
modeset_init iterates through all the registered omapdss devices and has some
initial checks to see if the panel has a driver and the required driver ops for
it to be usable by omapdrm.
The function bails out from modeset_init if a panel doesn't meet the
requirements, and stops the registration of the future panels and encoders which
come after it, that isn't the correct thing to do, we should go through the rest
of the panels. Replace the 'return's with 'continue's.
Signed-off-by: Archit Taneja <archit@ti.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When not using DSI PLL to generate the pixel clock, but DSS FCK, the
possible pixel clock rates are rather limited. DSS FCK is currently used
on OMAP2 and OMAP3.
When using Beagleboard with a monitor that supports high resolutions,
the clock rates do not match (at least for me) for the monitor's pixel
clocks within the current threshold in the code, which is +/- 1MHz.
This patch widens the search up to +/- 15MHz. The search is done in
steps, i.e. it first tries to find a rather exact clock, than a bit less
exact, etc. so this should not change the cases where a clock was
already found.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DSS func clock is calculated with prate / div * m. However, the current
omapdss code calculates it with prate * m / div, which yields a slightly
different result when there's a remainder. For example, 432000000 / 14 *
2 = 61714284, but 432000000 * 2 / 14 = 61714285.
In addition to that, the clock framework wants the clock rate given with
clk_set_rate to be higher than the actual (truncated) end result. So, if
prate is 432000000, and div is 14, the real result is 30857142.8571...
We need to call clk_set_rate with 30857143, which gives us a clock of
30857142. That's why we need to use DIV_ROUND_UP() when calling
clk_set_rate.
This patch fixes the clock calculation.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use the new clock calculation code in the DSI driver.
The new code does not need DSI video mode parameters from the panel
driver, like the old code does. Instead the new code is given the normal
video timings, and a few DSI parameters, which are used to create DSI
video timings.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add new way to iterate over DSI PLL and HSDIV clock divisors.
dsi_pll_calc() and dss_hsdiv_calc() provide a generic way to go over
all the divisors, within given clock range. The functions will call a
callback function for each divider set, making the function reusable for
all use cases.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add new way to iterate over DSS clock divisors. dss_div_calc() provides
a generic way to go over all the divisors, within given clock range.
dss_div_calc() will call a callback function for each divider set,
making the function reusable for all use cases.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add new way to iterate over DISPC clock divisors. dispc_div_calc()
provides a generic way to go over all the divisors, within given pixel
clock range. dispc_div_calc() will call a callback function for each
divider set, making the function reusable for all use cases.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We always use the same clock sources for DSI, so let's remove the
unnecessary clock source fields from dsi_data.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Instead of managing DSI sync ends with booleans, add an enum for the DSI
transfer mode. This is much cleaner way to handle the DSI syncs.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
To find out the DSI line buffer size we need to read HW registers. To
make it possible to do DSI configuration calculations without HW powered
up, store the line buffer size at DSI driver's probe.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We have a bunch of dsi functions that are used to do the basic
configuration for DSI. To simplify things, and to make sure we have all
the necessary information, create a single dsi config function, which
does the basic configuration.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dsi_configure_dispc_clocks() stores dsi func clock into unsigned long
long, but it should really be just unsigned long. Fix this.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
On OMAP5 the DISPC channels and DSI PLLs are not connected the same way.
LCD2 on OMAP5 cannot use any DSI PLL as a source clock, but LCD3 can use
DSI2's PLL.
This patch fixes dpi_get_dsidev() by adding separate case for OMAP5 to
handle the difference.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
Taal panel driver has support to set rotation and mirroring. However,
these features cannot be used without causing tearing, and are never
used. The code is just extra bloat, so let's remove it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
During the initialization of the DSI protocol registers, we always set
the sources of all DSI channels to L4. However, we don't update the
value in the dsi_data, so we may end up with a different value in the
register and in the dsi_data, leading to DSI problems.
This patch fixes the issue by initializing also the channel source in
the dsi_data.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
We currently setup both DSI and DISPC related things when the DSI bus is
enabled. There's no need for DISPC related thing at that point, though,
but only later when the video output is enabled.
To make it possible to use the DSI bus before DISPC overlay manager is
selected, this patch moves DSI's DISPC initialization to
dsi_enable_video_output(), from omapdss_dsi_display_enable(). We also
move the selection of DISPC's LCD clock to dsi_enable_video_output.
This way there are no DISPC dependencies until the video output is
enabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
The DISPC channel used for each output is currently passed in panel
platform data from the board files.
To simplify this, and to make the panel drivers less dependent on OMAP,
this patch changes omapdss to resolve the channel independently. The
channel is resolved based on the OMAP version and, in case of DSI, the
DSI module id. This resolved channel is stored into a new field in
output, dispc_channel.
The few places where dssdev->channel was used are changed to use
output->recommended_channel. After this patch, dssdev->channel is
obsolete.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
Add name field to omapdss's outputs so that in the following patches
panels refer to the output by their name. The name also helps debugging.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
Move hdmi driver's output initialization a bit earlier, so that it
happens before hdmi panel init. In the future the hdmi panel will depend
on the output being ready.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
omap_dss_get_output() is a public function, but was missing
EXPORT_SYMBOL().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
dss_mgr_wait_for_vsync() uses dssdev->type to find out if the output is
going to VENC, HDMI, or something else. This creates a dependency on
dssdev, which we want to remove. The task is more logically done by
looking at the output to which the overlay manager in question is
connected to.
This patch changes the code to use output->id to find out which kind of
output we use.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
Taal panel driver was originally meant to support multiple different DSI
command mode panel models. This never realized, and the multi-panel
support code is lying there unused, making the driver more difficult to
maintain.
This patch removes the multi-panel support from Taal driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
The role of struct omap_dss_device will change in the future. The exact
details of that are still a bit unclear. However, the less uses of
omap_dss_device we have, the easier the change is in the future.
This patch removes uses of omap_dss_device from dsi.c, where it can be
done easily. Mostly this means passing dsi platform device to functions,
instead of the omap_dss_device.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
The role of struct omap_dss_device will change in the future. The exact
details of that are still a bit unclear. However, the less uses of
omap_dss_device we have, the easier the change is in the future.
This patch removes uses of omap_dss_device from dpi.c, where it can be
done neatly, by, for example, passing some lower level parameter in
function parameters.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
struct omap_dss_device contains HDMI clock divisors. The idea is that the
board file can pass precalculated divisors to the display driver.
However, these divsors are no longer needed, as the omapdss driver can
calculate the divisors during runtime.
This patch removes the divisors from omap_dss_device, and their uses
from the hdmi driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
struct omap_dss_device contains DSS clock divisors. The idea is that the
board file can pass precalculated divisors to the display driver.
However, these divsors are no longer needed, as the omapdss driver can
calculate the divisors during runtime.
This patch removes the divisors from omap_dss_device, and their uses
from the dsi driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
Pull slave-dmaengine fixes from Vinod Koul:
"Two fixes for slave-dmaengine.
The first one is for making slave_id value correct for dw_dmac and
the other one fixes the endieness in DT parsing"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dw_dmac: adjust slave_id accordingly to request line base
dmaengine: dw_dma: fix endianess for DT xlate function
Pull media fixes from Mauro Carvalho Chehab:
"For a some fixes for Kernel 3.9:
- subsystem build fix when VIDEO_DEV=y, VIDEO_V4L2=m and I2C=m
- compilation fix for arm multiarch preventing IR_RX51 to be selected
- regression fix at bttv crop logic
- s5p-mfc/m5mols/exynos: a few fixes for cameras on exynos hardware"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] [REGRESSION] bt8xx: Fix too large height in cropcap
[media] fix compilation with both V4L2 and I2C as 'm'
[media] m5mols: Fix bug in stream on handler
[media] s5p-fimc: Do not attempt to disable not enabled media pipeline
[media] s5p-mfc: Fix encoder control 15 issue
[media] s5p-mfc: Fix frame skip bug
[media] s5p-fimc: send valid m2m ctx to fimc_m2m_job_finish
[media] exynos-gsc: send valid m2m ctx to gsc_m2m_job_finish
[media] fimc-lite: Fix the variable type to avoid possible crash
[media] fimc-lite: Initialize 'step' field in fimc_lite_ctrl structure
[media] ir: IR_RX51 only works on OMAP2
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=u2RH
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20130331' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Alright, this time from 10K up in the air.
Collection of fixes that have been queued up since the merge window
opened, hence postponed until later in the cycle. The pull request
contains:
- A bunch of fixes for the xen blk front/back driver.
- A round of fixes for the new IBM RamSan driver, fixing various
nasty issues.
- Fixes for multiple drives from Wei Yongjun, bad handling of return
values and wrong pointer math.
- A fix for loop properly killing partitions when being detached."
* tag 'for-linus-20130331' of git://git.kernel.dk/linux-block: (25 commits)
mg_disk: fix error return code in mg_probe()
rsxx: remove unused variable
rsxx: enable error return of rsxx_eeh_save_issued_dmas()
block: removes dynamic allocation on stack
Block: blk-flush: Fixed indent code style
cciss: fix invalid use of sizeof in cciss_find_cfgtables()
loop: cleanup partitions when detaching loop device
loop: fix error return code in loop_add()
mtip32xx: fix error return code in mtip_pci_probe()
xen-blkfront: remove frame list from blk_shadow
xen-blkfront: pre-allocate pages for requests
xen-blkback: don't store dev_bus_addr
xen-blkfront: switch from llist to list
xen-blkback: fix foreach_grant_safe to handle empty lists
xen-blkfront: replace kmalloc and then memcpy with kmemdup
xen-blkback: fix dispatch_rw_block_io() error path
rsxx: fix missing unlock on error return in rsxx_eeh_remap_dmas()
Adding in EEH support to the IBM FlashSystem 70/80 device driver
block: IBM RamSan 70/80 error message bug fix.
block: IBM RamSan 70/80 branding changes.
...
This reverts commit 6aa9707099c4b25700940eb3d016f16c4434360d.
Commit 6aa9707099c4 ("lockdep: check that no locks held at freeze time")
causes problems with NFS root filesystems. The failures were noticed on
OMAP2 and 3 boards during kernel init:
[ BUG: swapper/0/1 still has locks held! ]
3.9.0-rc3-00344-ga937536 #1 Not tainted
-------------------------------------
1 lock held by swapper/0/1:
#0: (&type->s_umount_key#13/1){+.+.+.}, at: [<c011e84c>] sget+0x248/0x574
stack backtrace:
rpc_wait_bit_killable
__wait_on_bit
out_of_line_wait_on_bit
__rpc_execute
rpc_run_task
rpc_call_sync
nfs_proc_get_root
nfs_get_root
nfs_fs_mount_common
nfs_try_mount
nfs_fs_mount
mount_fs
vfs_kern_mount
do_mount
sys_mount
do_mount_root
mount_root
prepare_namespace
kernel_init_freeable
kernel_init
Although the rootfs mounts, the system is unstable. Here's a transcript
from a PM test:
http://www.pwsan.com/omap/testlogs/test_v3.9-rc3/20130317194234/pm/37xxevm/37xxevm_log.txt
Here's what the test log should look like:
http://www.pwsan.com/omap/testlogs/test_v3.8/20130218214403/pm/37xxevm/37xxevm_log.txt
Mailing list discussion is here:
http://lkml.org/lkml/2013/3/4/221
Deal with this for v3.9 by reverting the problem commit, until folks can
figure out the right long-term course of action.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Mandeep Singh Baines <msb@chromium.org>
Cc: Jeff Layton <jlayton@redhat.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: <maciej.rutecki@gmail.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ben Chan <benchan@chromium.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull SCSI target fixes from Nicholas Bellinger:
"This includes the bug-fix for a >= v3.8-rc1 regression specific to
iscsi-target persistent reservation conflict handling (CC'ed to
stable), and a tcm_vhost patch to drop VIRTIO_RING_F_EVENT_IDX usage
so that in-flight qemu vhost-scsi-pci device code can detect the
proper vhost feature bits.
Also, there are two more tcm_vhost patches still being discussed by
MST and Asias for v3.9 that will be required for the in-flight qemu
vhost-scsi-pci device patch to function properly, and that should
(hopefully) be the last target fixes for this round."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: Fix RESERVATION_CONFLICT status regression for iscsi-target special case
tcm_vhost: Avoid VIRTIO_RING_F_EVENT_IDX feature bit
On some hardware configurations we have got the request line with the offset.
The patch introduces convert_slave_id() helper for that cases. The request line
base is came from the driver data provided by the platform_device_id table.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
As reported by Wu Fengguang's build robot tracking sparse warnings, the
dma_spec arguments in the dw_dma_xlate are already byte swapped on
little-endian platforms and must not get swapped again. This code is
currently not used anywhere, but will be used in Linux 3.10 when the
ARM SPEAr platform starts using the generic DMA DT binding.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The Adam Belay's e-mail address in MAINTAINERS under PNP SUPPORT
is not valid any more and I started to maintain that code in the
meantime as a matter of fact, so list myself as a maintainer of it
along with Bjorn and remove the Adam's entry from it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull ceph fix from Sage Weil:
"This fixes a regression introduced during the last merge window when
mapping non-existent images."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: don't zero-fill non-image object requests
A result of ENOENT from a read request for an object that's part of
an rbd image indicates that there is a hole in that portion of the
image. Similarly, a short read for such an object indicates that
the remainder of the read should be interpreted a full read with
zeros filling out the end of the request.
This behavior is not correct for objects that are not backing rbd
image data. Currently rbd_img_obj_request_callback() assumes it
should be done for all objects.
Change rbd_img_obj_request_callback() so it only does this zeroing
for image objects. Encapsulate that special handling in its own
function. Add an assertion that the image object request is a bio
request, since we assume that (and we currently don't support any
other types).
This resolves a problem identified here:
http://tracker.ceph.com/issues/4559
The regression was introduced by bf0d5f503dc11d6314c0503591d258d60ee9c944.
Reported-by: Dan van der Ster <dan@vanderster.com>
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-off-by: Sage Weil <sage@inktank.com>
Pull btrfs fixes from Chris Mason:
"We've had a busy two weeks of bug fixing. The biggest patches in here
are some long standing early-enospc problems (Josef) and a very old
race where compression and mmap combine forces to lose writes (me).
I'm fairly sure the mmap bug goes all the way back to the introduction
of the compression code, which is proof that fsx doesn't trigger every
possible mmap corner after all.
I'm sure you'll notice one of these is from this morning, it's a small
and isolated use-after-free fix in our scrub error reporting. I
double checked it here."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: don't drop path when printing out tree errors in scrub
Btrfs: fix wrong return value of btrfs_lookup_csum()
Btrfs: fix wrong reservation of csums
Btrfs: fix double free in the btrfs_qgroup_account_ref()
Btrfs: limit the global reserve to 512mb
Btrfs: hold the ordered operations mutex when waiting on ordered extents
Btrfs: fix space accounting for unlink and rename
Btrfs: fix space leak when we fail to reserve metadata space
Btrfs: fix EIO from btrfs send in is_extent_unchanged for punched holes
Btrfs: fix race between mmap writes and compression
Btrfs: fix memory leak in btrfs_create_tree()
Btrfs: fix locking on ROOT_REPLACE operations in tree mod log
Btrfs: fix missing qgroup reservation before fallocating
Btrfs: handle a bogus chunk tree nicely
Btrfs: update to use fs_state bit
Commit 3e7fc708eb41 ("ia64 idle: delete pm_idle") in 3.9-rc1 didn't
finish the job, leaving an un-initialized reference to (*idle)().
[ Haven't seen a crash from this - but seems like we are just being
lucky that "idle" is zero so it does get initialized before we jump to
randomland - Len ]
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull arc architecture fixes from Vineet Gupta:
"This includes fix for a serious bug in DMA mapping API, make
allyesconfig wreckage, removal of bogus email-list placeholder in
MAINTAINERS, a typo in ptrace helper code and last remaining changes
for syscall ABI v3 which we are finally starting to transition-to
internally.
The request is late than I intended to - but I was held up with
debugging a timer link list corruption, for which a proposed fix to
generic timer code was sent out to lkml/tglx earlier today."
* 'for-curr' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: Fix the typo in event identifier flags used by ptrace
arc: fix dma_address assignment during dma_map_sg()
ARC: Remove SET_PERSONALITY (tracks cross-arch change)
ARC: ABIv3: fork/vfork wrappers not needed in "no-legacy-syscall" ABI
ARC: ABIv3: Print the correct ABI ver
ARC: make allyesconfig build breakages
ARC: MAINTAINERS update for ARC
A user reported a panic where we were panicing somewhere in
tree_backref_for_extent from scrub_print_warning. He only captured the trace
but looking at scrub_print_warning we drop the path right before we mess with
the extent buffer to print out a bunch of stuff, which isn't right. So fix this
by dropping the path after we use the eb if we need to. Thanks,
Cc: stable@vger.kernel.org
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
