DAPM widgets can be classified into four categories:
* supply: Supply widgets do not affect the power state of their
non-supply widget neighbors and unlike other widgets a
supply widget is not powered up when it is on an active
path, but when at least on of its neighbors is powered up.
* source: A source is a widget that receives data from outside the
DAPM graph or generates data. This can for example be a
microphone, the playback DMA or a signal generator. A source
widget will be considered powered up if there is an active
path to a sink widget.
* sink: A sink is a widget that transmits data to somewhere outside
of the DAPM graph. This can e.g. be a speaker or the capture
DMA. A sink widget will be considered powered up if there is
an active path from a source widget.
* normal: Normal widgets are widgets not covered by the categories
above. A normal widget will be considered powered up if it
is on an active path between a source widget and a sink
widget.
The way the number of input and output paths for a widget is calculated
depends on its category. There are a bunch of factors which decide which
category a widget is. Currently there is no formal classification of these
categories and we calculate the category of the widget based on these
factors whenever we want to know it. This is at least once for every widget
during each power update sequence. The factors which determine the category
of the widgets are mostly static though and if at all change rather seldom.
This patch introduces three new per widget flags, one for each of non-normal
widgets categories. Instead of re-computing the category each time we want
to know them the flags will be checked. For the majority of widgets the
category is solely determined by the widget id, which means it never changes
and only has to be set once when the widget is created. The only widgets
with dynamic categories are:
snd_soc_dapm_dai_out: Is considered a sink iff the capture stream is
active, otherwise normal.
snd_soc_dapm_dai_in: Is considered a source iff the playback stream
is active, otherwise normal.
snd_soc_dapm_input: Is considered a sink iff it has no outgoing
paths, otherwise normal.
snd_soc_dapm_output: Is considered a source iff it has no incoming
paths, otherwise normal.
snd_soc_dapm_line: Is considered a sink iff it has no outgoing paths
and is considered a source iff it has no incoming paths,
otherwise normal.
For snd_soc_dapm_dai_out/snd_soc_dapm_dai_in widgets the category will be
updated when a stream is started or stopped. For the other dynamic widgets
the category will be updated when a path connecting to it is added or
removed.
Introducing those new widget categories allows to make
is_connected_{output,input}_ep, which are among the hottest paths of the
DAPM algorithm, more generic and significantly shorter.
The before and after sizes for is_connected_{output,input}_ep are:
On ARM (defconfig + CONFIG_SND_SOC):
function old new delta
is_connected_output_ep 480 340 -140
is_connected_input_ep 456 352 -104
On amd64 (defconfig + CONFIG_SND_SOC):
function old new delta
is_connected_output_ep 579 427 -152
is_connected_input_ep 563 427 -136
Which is about a 25%-30% decrease, other architectures are expected to have
similar numbers. At the same time the size of the snd_soc_dapm_widget struct
does not change since the new flags are stored in the same word as the
existing flags.
Note: that since the per widget 'ext' flag was only used to decide whether a
snd_soc_dapm_input or snd_soc_dapm_output widget was a source or a sink it
is now unused and can be removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Controls on a path only have an effect if the sink on the path is either a
mixer or mux widget. Currently we sort of silently ignore controls on other
paths, but since they don't do anything having them on other paths does not
make much sense and it is probably safe to assume that if we see such a path
it is a mistake in the driver that registered the path. This patch modifies
snd_soc_dapm_add_path() to report an error if a path with and control is
encountered where we didn't expect a control. This also allows to simplify
the code quite a bit.
The patch also moves the connecting of the path lists out of
dapm_connect_mux() and dapm_connect_mixer() into snd_soc_dapm_add_path().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Paths that are directly connected to a MUX widget are not affected by
changes to the MUX's control. Rather than checking if a path is directly
connected each time the MUX is updated do it only once when MUX is created.
We can also remove the check for e->texts[mux] != NULL, since if that
condition was true the code would have had already crashed much earlier (And
generally speaking if a enum's 'texts' entry is NULL it's a bug in the
driver).
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rework soc_dapm_{mixer,mux}_update_power() to only mark a path dirty if the
connect state if the path has actually changed. This avoids unnecessary
power state checks for the widgets involved.
Also factor out the common code that is involved in this into a helper
function.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The 'walked' flag was used to avoid walking paths that have already been
walked. But since we started caching the number of inputs and outputs of a
path we never actually get into a situation where we try to walk a path that
has the 'walked' flag set.
There are two cases in which we can end up walking a path multiple times
within a single run of is_connected_output_ep() or is_connected_input_ep().
1) If a path splits up and rejoins later:
.--> C ---v
A -> B E --> F
'--> D ---^
When walking from A to F we'll end up at E twice, once via C and once via D.
But since we do a depth first search we'll fully discover the path and
initialize the number of outputs/inputs of the widget the first time we get
there. The second time we get there we'll use the cached value and not
bother to check any of the paths again. So we'll never see a path where
'walked' is set in this case.
2) If there is a circle:
A --> B <-- C <-.--> F
'--> D ---'
When walking from A to F we'll end up twice at B. But since there is a
circle the 'walking' flag will still be set on B once we get there the
second time. This means we won't look at any of it's outgoing paths. So in
this case we won't ever see a path where 'walked' is set either.
So it is safe to remove the flag. This on one hand means we remove some
always true checks from one of the hottest paths of the DAPM algorithm and
on the other hand means we do not have to do the tedious clearing of the
flag after checking the number inputs or outputs of a widget.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
dapm_adc_check_power() checks if the widget is active, if yes it only checks
whether there are any connected input paths. Otherwise it calls
dapm_generic_check_power() which will check for both connected input and
output paths. But the function that checks for connected output paths will
return true if the widget is a active sink. Which means the generic power
check function will work just fine and there is no need for a special power
check function.
The same applies for dapm_dac_check_power(), but with input and output paths
reversed.
This patch removes both dapm_adc_check_power() and dapm_dac_check_power()
and replace their usage with dapm_generic_check_power().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
A path has always a valid source and a valid sink otherwise we wouldn't add
it in the first place. Hence all tests that check if sink/source is non NULL
always evaluate to true and can be removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Each widget has a list of all the paths that it is connected to. There is no
need to iterate over all paths when we are only interested in the paths of a
specific widget.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Both path->name and e->texts[i] have type const char*, so the cast is
slightly confusing and certainly unnecessary.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Coverity spotted the following possible use-after-free condition in
dapm_create_or_share_mixmux_kcontrol():
If kcontrol is NULL, and (wname_in_long_name && kcname_in_long_name)
validates to true, 'name' will be set to an allocated string, and be
freed a few lines later via the 'long_name' alias. 'name', however,
is used by dev_err() in case snd_ctl_add() fails.
Fix this by adding a jump label that frees 'long_name' at the end of
the function.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Commit 0bd2ac3dae74 ("ASoC: Remove CODEC pointer from snd_soc_dapm_context")
introduced regression to snd_soc_dapm_new_controls() when registering a card
with card->dapm_widgets set. Call chain is:
snd_soc_register_card()
-> snd_soc_instantiate_card()
-> snd_soc_dapm_new_controls()
-> snd_soc_dapm_new_control()
Null pointer dereference occurs since card->dapm context doesn't have
associated component. Fix this by setting widget codec pointer
conditionally.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DSP driver needs to know widget control value in its event handler for
widgets like mixers. This is required in the subsequent patches
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The only remaining user of the CODEC pointer in the DAPM struct is to
initialize the CODEC pointer in the widget struct. The later is scheduled
for removal, but has still a few users left. For now use
dapm->component->codec to initialize it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a substantial amount of drivers that in go to SND_SOC_BIAS_OFF on
suspend and go back to SND_SOC_BIAS_SUSPEND on resume (Often this is even
the only thing done in the suspend and resume handlers). This patch
introduces a new suspend_bias_off flag, which when set by a driver will let
the ASoC core automatically put the device's DAPM context at the
SND_SOC_BIAS_OFF level during suspend. Once the device is resumed the DAPM
context will go back to SND_SOC_BIAS_STANDBY (if the context is idle,
otherwise to SND_SOC_BIAS_ON).
This will allow us to remove a fair bit of duplicated code from the drivers.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
If soc_dapm_read() fails, reg_val will be uninitialized, and bogus
values will be written later:
sound/soc/soc-dapm.c: In function 'snd_soc_dapm_get_enum_double':
sound/soc/soc-dapm.c:2862:15: warning: 'reg_val' may be used uninitialized in this function [-Wmaybe-uninitialized]
unsigned int reg_val, val;
^
Return early on error to fix this.
Introduced by commit ce0fc93ae56e2ba50ff8c220d69e4e860e889320 ("ASoC:
Add DAPM support at the component level").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Both the snd_soc_codec and snd_soc_platform struct do have a pointer to the
parent card and both handle this pointer in mostly the same way. This patch
moves the card field to the component level which will allow further code
consolidation between platforms and CODECS.
Since there are only a handful of users of the snd_soc_codec struct's card field
(and none of the snd_soc_platform's) these are update in this patch as well,
which allows it to be removed from the snd_soc_codec struct.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
It was accidentally added in commit 44ba2641 ("ASoC: dapm: Add support for DAI
multicodec").
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add a function helper to factorize the hw_params code.
Suggested by Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Tested-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The platform field in the snd_soc_dapm_widget and snd_soc_dapm_context structs
is now unused can be removed. New code that wants to get the platform for a
widget or dapm context should use snd_soc_dapm_to_platform(w->dapm) or
snd_soc_dapm_to_platform(dapm).
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds full DAPM support at the component level. Previously there was
only full DAPM support for CODECs and partial DAPM support (e.g. no Mixers nor
MUXs) for platforms. Having DAPM support at the component level will allow all
types of components to use DAPM and also help in consolidating the DAPM support
between CODECs and platforms.
Since the DAPM context is directly embedded into the snd_soc_codec and
snd_soc_platform struct and the 'dapm' field is directly referenced in a lot of
drivers moving the field just right now is not possible without causing code
churn. The approach this patch takes is to add two new fields to the component
struct. One field which is the pointer to the actual DAPM context used by the
component and one DAPM context that will be used as the default if no other
context was specified. For CODECs and platforms the pointer is initialized to
point to the CODEC or platform DAPM context. All generic code when referencing
a component's DAPM struct will go via the pointer. This will make it possible to
eventually seamlessly move the DAPM context from snd_soc_codec and
snd_soc_platform struct over once all direct references have been eliminated.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently the DAPM code directly looks at the CODEC driver struct to get a
handle to the set_bias_level() callback. This patch adds a new set_bias_level()
callback to the DAPM context struct. The DAPM code will use this new callback
instead of the CODEC callback. For CODECs the new callback is set up to call the
CODEC specific set_bias_level callback(). Not looking directly at the CODEC
driver struct will allow non CODEC DAPM contexts to implement a set_bias_level()
callback.
This is also similar to how the seq_notifier() and stream_event() callbacks are
currently handled.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently only pins in CODEC DAPM contexts are automatically marked as
non-connected if the card has the fully_routed flag set. This makes sense since
widgets which qualify for auto-disconnection are only found in CODEC DAPM
contexts. But with componentisation this is going to change, so consider all
widgets for auto-disconnection.
Also it is probably faster to walk the widgets list only once rather than once
for each CODEC.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The component struct already has a name and id field which are initialized to
the same values as the same fields in the CODEC and platform structs. So remove
them from the CODEC and platform structs and used the ones from the component
struct instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Move the name_prefix from the CODEC struct to the component struct. This will
eventually allow to specify prefixes for all types of components. It is also
necessary to make the DAPM code component type independent (i.e. a DAPM context
does not need to know whether it belongs to a CODEC or a platform or something
else).
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit c9e065c27fe9 ("ASoC: dapm: Make sure to always update the DAPM graph
in _put_volsw()") stopped updating register values in those cases where
initial after boot state of kcontrol appears to not change but where
register value still needs update because it is not in sync with the
kcontrol state.
Fix this by doing snd_soc_test_bits() unconditionally as it was before but
by using separate flags for kcontrol and register state changes. This allow
both DAPM graph to be updated when disabling auto-muted control and update
register if it is out-of-sync in respect of kcontrol state.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently when the DAPM context bias level is SUSPEND and the target bias level
is OFF dapm_pre_sequence_async() will first transition to PREPARE and
dapm_post_sequence_async() will then transition back from PREPARE to STANDBY and
then to OFF.
This patch makes sure that dapm_pre_sequence_async() only transitions to PREPARE
when either going to ON or away from ON. This avoids the extra unnecessary
transitions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit commit de9ba98b6d ("ASoC: dapm: Make widget power register settings more
flexible") added generic support for on_val/off_val in the DAPM core. With this
in place there is no need anymore for having a special event callback for
SND_SOC_DAPM_REG() widgets.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
If we find a widget who's stream name matches the name of a DAI widget then
thats the one it should be connected to. Based on the widget id we can say in
which direction the path should be. No need to go back to the DAI and check the
stream names.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
We already know the widgets we want to connect, so use snd_soc_dapm_add_path()
instead of snd_soc_dapm_add_route() in snd_soc_dapm_new_pcm().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
We already know which two widgets should be connected, so use
snd_soc_dapm_add_path() instead of snd_soc_dapm_add_route() in
snd_soc_dapm_connect_dai_link_widgets().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This reverts commit bd23c5b661858446267f4d6b2fb4edd8eb710dda.
The patch claims that the patch is necessary to avoid double prefix addition
when calling snd_soc_dapm_add_route() from snd_soc_dapm_connect_dai_link_widgets().
But snd_soc_dapm_add_route() is called with the card's DAPM context, which does
not have a prefix, which means there is no prefix that could be added a second
time.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
For CODEC to CODEC DAI links the paths are created in snd_soc_dapm_new_pcm().
Also for CODEC to CODEC links the widgets are connected cross-over via a DAI
link widget, meaning that the capture widget of one CODEC will be connected to
the playback widget of the other and vice versa. Whereas
snd_soc_dapm_connect_dai_link_widgets() directly connects the playback widget of
the CPU DAI to the playback widget of the CODEC DAI and the capture widget of
the CPU DAI to the capture widget of the CODEC DAI. So not skipping
CODEC<->CODEC links in snd_soc_dapm_connect_dai_link_widgets() will create
incorrect connections between the two CODECs which will cause DAPM to detect
active paths where there are none and unnecessarily power up widgets.
Fixes: b893ea5 ("ASoC: sapm: Automatically connect DAI link widgets in DAPM graph.")
Cc: <stable@vger.kernel.org> (for 3.14+)
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
When using auto-muted controls it may happen that the register value will not
change when changing a control from enabled to disabled (since the control might
be physically disabled due to the auto-muting). We have to make sure to still
update the DAPM graph and disconnect the mixer input.
Fixes: commit 5729507 ("ASoC: dapm: Implement mixer input auto-disable")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
In soc_dapm_stream_event() we have the same code twice, once for the codec_dai
and once for the cpu_dai. This patch factors the duplicated code out into a
separate function. This will make it easier to modify the implementation (since
there is only one place that needs to be updated) and also easier to add support
for more than two DAIs per DAI link.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is no unlocked version of soc_widget_update_bits_locked() and there is no
plan to introduce it in the near future, so drop the _locked suffix.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
We currently have two very similar IO abstractions in ASoC, one for CODECs, the
other for platforms. Moving this to the component level will allow us to unify
those two. It will also enable us to move the standard kcontrol helpers as well
as DAPM support to the component level.
The new component level abstraction layer is primarily build around regmap.
There is a per component pointer for the regmap instance for the underlying
device. There are four new function snd_soc_component_read(),
snd_soc_component_write(), snd_soc_component_update_bits() and
snd_soc_component_update_bits_async(). They have the same signature as their
regmap counter-part and will internally forward the call one-to-one to regmap.
If the component it not using regmap it will fallback to using the custom IO
callbacks. This is done to be able to support drivers that haven't been
converted to regmap yet, but it is expected that this will eventually be removed
in the future once all component drivers have been converted to regmap.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit 9e1fda4ae158 ("ASoC: dapm: Implement mixer input auto-disable")
is trying to free the widget it allocated by snd_soc_dapm_new_control()
call in dapm_kcontrol_data_alloc() by adding kfree(data->widget) to
dapm_kcontrol_free().
This is causing a widget double free with auto-disabled DAPM kcontrols
in sound card unregistration because widgets are already freed before
dapm_kcontrol_free() is called.
Reason for that is all widgets are added into dapm->card->widgets list
in snd_soc_dapm_new_control() and freed in dapm_free_widgets() during
execution of snd_soc_dapm_free().
Now snd_soc_dapm_free() calls for different DAPM contexts happens before
snd_card_free() call from where the call chain to dapm_kcontrol_free()
begins:
soc_cleanup_card_resources()
soc_remove_dai_links()
soc_remove_link_dais()
snd_soc_dapm_free(&cpu_dai->dapm)
soc_remove_link_components()
soc_remove_platform()
snd_soc_dapm_free(&platform->dapm)
soc_remove_codec()
snd_soc_dapm_free(&codec->dapm)
snd_soc_dapm_free(&card->dapm)
snd_card_free()
snd_card_do_free()
snd_device_free_all()
snd_device_free()
snd_ctl_dev_free()
snd_ctl_remove()
snd_ctl_free_one()
dapm_kcontrol_free()
This wasn't making harm with ordinary DAPM kcontrols since data->widget is NULL for
them.
Fixes: 9e1fda4ae158 (ASoC: dapm: Implement mixer input auto-disable)
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
This patch change reg's type from unsigned short to int.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Try to spot locking issues by asserting that the DAPM mutex is held when
it should be. There's a bit of fun due to us not requiring the lock to be
held prior to the card being instantiated which mean we need to wrap the
assert in some paths and this isn't methodical by any stretch of the
imagination.
Signed-off-by: Mark Brown <broonie@linaro.org>
The new sequence ensure that dapm_pre_sequence_async work on
the card before all codecs and dapm_post_sequence_async work
on the card after all codecs.
So the machine driver could utilize the determinate sequence
to do the gloabl setup and teardown in the right place.
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
