Some PHY drivers like the generic one do not provide a read_status
callback on their own but rely on genphy_read_status being called
directly.
With the current code, this results in a NULL function pointer call.
Call genphy_read_status instead when there is no specific callback.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell reported the following race in the phylib state machine
(quoting from his mail):
if (phy_polling_mode(phydev) && phy_is_started(phydev))
phy_queue_state_machine(phydev, PHY_STATE_TIME);
state = PHY_UP
thread 0 thread 1
phy_disconnect()
+-phy_is_started()
phy_is_started() |
`-phy_stop()
+-phydev->state = PHY_HALTED
`-phy_stop_machine()
`-cancel_delayed_work_sync()
phy_queue_state_machine()
`-mod_delayed_work()
At this point, the phydev->state_queue() has been added back onto the
system workqueue despite phy_stop_machine() having been called and
cancel_delayed_work_sync() called on it.
Fix this by protecting the complete operation in thread 0.
Fixes: 2b3e88ea6528 ("net: phy: improve phy state checking")
Reported-by: Russell King - ARM Linux admin <linux@armlinux.org.uk>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell suggested to remove the locking from phy_is_started() because
the read is atomic anyway and actually the locking may be more
misleading.
Fixes: 2b3e88ea6528 ("net: phy: improve phy state checking")
Suggested-by: Russell King - ARM Linux admin <linux@armlinux.org.uk>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phylib enables interrupts before phy_start() has been called, and if
we receive an interrupt in a non-started state, the interrupt handler
returns IRQ_NONE. This causes problems with at least one Marvell chip
as reported by Andrew.
Fix this by handling interrupts the same as in phy_mac_interrupt(),
basically always running the phylib state machine. It knows when it
has to do something and when not.
This change allows to handle interrupts gracefully even if they
occur in a non-started state.
Fixes: 2b3e88ea6528 ("net: phy: improve phy state checking")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During testing on Armada 388 platforms, it was found with a certain
module configuration that it was possible to trigger a kernel oops
during the module load process, caused by the phylink resolver being
triggered for a currently disabled interface.
This problem was introduced by changing the way the SFP registration
works, which now can result in the sfp link down notification being
called during phylink_create().
Fixes: b5bfc21af5cb ("net: sfp: do not probe SFP module before we're attached")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we probe a SFP module, we expect to be able to call the upstream
device's module_insert() function so that the upstream link can be
configured. However, when the upstream device is delayed, we currently
may end up probing the module before the upstream device is available,
and lose the module_insert() call.
Avoid this by holding off probing the module until the SFP bus is
properly connected to both the SFP socket driver and the upstream
driver.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
During sendmsg() a cloned skb is saved via dp83640_txtstamp() in
->tx_queue. After the NIC sends this packet, the PHY will reply with a
timestamp for that TX packet. If the cable is pulled at the right time I
don't see that packet. It might gets flushed as part of queue shutdown
on NIC's side.
Once the link is up again then after the next sendmsg() we enqueue
another skb in dp83640_txtstamp() and have two on the list. Then the PHY
will send a reply and decode_txts() attaches it to the first skb on the
list.
No crash occurs since refcounting works but we are one packet behind.
linuxptp/ptp4l usually closes the socket and opens a new one (in such a
timeout case) so those "stale" replies never get there. However it does
not resume normal operation anymore.
Purge old skbs in decode_txts().
Fixes: cb646e2b02b2 ("ptp: Added a clock driver for the National Semiconductor PHYTER.")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 6623c0fba10ef45b64ca213ad5dec926f37fa9a0.
The original diagnosis was incorrect: it appears that the NIC had
PHY polling mode enabled, which meant that it overwrote the PHYs
advertisement register during negotiation.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A few PHY drivers have the GPLv2+ license text. They then either have
a MODULE_LICENSE() of GPLv2 only, or an SPDX tag of GPLv2 only.
Since the license text is much easier to understand than either the
SPDX tag or the MODULE_LICENSE, use it as the definitive source of the
licence, and fixup the others when there are contradictions.
Cc: David Wu <david.wu@rock-chips.com>
Cc: Dongpo Li <lidongpo@hisilicon.com>
Cc: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since phy driver features became a link_mode bitmap, phy drivers that
don't have a list of features configured will cause the kernel to crash
when probed.
Prevent the phy driver from registering if the features field is missing.
Fixes: 719655a14971 ("net: phy: Replace phy driver features u32 with link_mode bitmap")
Reported-by: Scott Wood <oss@buserror.net>
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy drivers for CS4340 and TN2020 are missing their
features attributes. Add them.
Fixes: 719655a14971 ("net: phy: Replace phy driver features u32 with link_mode bitmap")
Reported-by: Scott Wood <oss@buserror.net>
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bcm87xx and micrel driver has PHYs which are missing the .features
value. Add them. The bcm87xx is a 10G FEC only PHY. Add the needed
features definition of this PHY.
Fixes: 719655a14971 ("net: phy: Replace phy driver features u32 with link_mode bitmap")
Reported-by: Scott Wood <oss@buserror.net>
Reported-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the referenced commit, Ethernet fails to come up at boot on the
board meson-gxl-s905x-libretech-cc. Fix this by re-enabling the
genphy_soft_reset callback for the Amlogic Meson GXL PHY driver.
Fixes: 6e2d85ec0559 ("net: phy: Stop with excessive soft reset")
Signed-off-by: Timotej Lazar <timotej.lazar@araneo.si>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
m88e1318_set_wol() takes the lock as part of phy_select_page(). Don't
take the lock again with phy_read(), use the unlocked __phy_read().
Fixes: 424ca4c55121 ("net: phy: marvell: fix paged access races")
Reported-by: Åke Rehnman <ake.rehnman@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VOD can be out of spec, unless some magic value is poked into an
undocumented register in an undocumented page.
Fixes: e4cf8a38fc0d ("net: phy: Marvell: Add mv88e6390 internal PHY")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far genphy_soft_reset was used automatically if the PHY driver
didn't implement the soft_reset callback. This changed with the
mentioned commit and broke KSZ9031. To fix this configure the
KSZ9031 PHY driver to use genphy_soft_reset.
Fixes: 6e2d85ec0559 ("net: phy: Stop with excessive soft reset")
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding checks to detect wrong usage of the phylib API we added
a check to phy_start_aneg() which is too strict. If the phylib
state machine is in state PHY_HALTED we should allow reconfiguring
and restarting aneg, and just don't touch the state.
Fixes: 2b3e88ea6528 ("net: phy: improve phy state checking")
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
Even though the link is down before entering hibernation,
there is an issue that the network interface always links up after resuming
from hibernation.
If the link is still down before enabling the network interface,
and after resuming from hibernation, the phydev->state is forcibly set
to PHY_UP in mdio_bus_phy_restore(), and the link becomes up.
In suspend sequence, only if the PHY is attached, mdio_bus_phy_suspend()
calls phy_stop_machine(), and mdio_bus_phy_resume() calls
phy_start_machine().
In resume sequence, it's enough to do the same as mdio_bus_phy_resume()
because the state has been preserved.
This patch fixes the issue by calling phy_start_machine() in
mdio_bus_phy_restore() in the same way as mdio_bus_phy_resume().
Fixes: bc87922ff59d ("phy: Move PHY PM operations into phy_device")
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
3c1bcc8614db ("net: ethernet: Convert phydev advertize and supported
from u32 to link mode") left some unused code in phy_probe(), remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far phy_error() silently stops the PHY state machine. If the network
driver doesn't inform about a MDIO error then the user may wonder why
his network is down. Let's print the stack trace to facilitate search
for the root cause of the error.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers phy_is_started() and __phy_is_started() to avoid open-coded
checks whether PHY has been started. To make the check easier move
PHY_HALTED before PHY_UP in enum phy_state. Further improvements:
phy_start_aneg():
Return -EBUSY and print warning if function is called from a non-started
state (DOWN, READY, HALTED). Better check because function is exported
and drivers may use it incorrectly.
phy_interrupt():
Return IRQ_NONE also if state is DOWN or READY. We should never receive
an interrupt in one of these states, but better play safe.
phy_stop():
Just return and print a warning if PHY is in a non-started state.
This warning should help to identify drivers with unbalanced calls to
phy_start() / phy_stop().
phy_state_machine():
Schedule state machine run only if PHY is in a started state.
E.g. if state is READY we don't need the state machine, it will be
started by phy_start().
v2:
- don't use __func__ within phy_warn_state
v3:
- use WARN() instead of printing error message to facilitate debugging
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers can use this as .ndo_change_carrier() to change carrier
via /sys/class/net/ethX/carrier.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several conflicts, seemingly all over the place.
I used Stephen Rothwell's sample resolutions for many of these, if not
just to double check my own work, so definitely the credit largely
goes to him.
The NFP conflict consisted of a bug fix (moving operations
past the rhashtable operation) while chaning the initial
argument in the function call in the moved code.
The net/dsa/master.c conflict had to do with a bug fix intermixing of
making dsa_master_set_mtu() static with the fixing of the tagging
attribute location.
cls_flower had a conflict because the dup reject fix from Or
overlapped with the addition of port range classifiction.
__set_phy_supported()'s conflict was relatively easy to resolve
because Andrew fixed it in both trees, so it was just a matter
of taking the net-next copy. Or at least I think it was :-)
Joe Stringer's fix to the handling of netns id 0 in bpf_sk_lookup()
intermixed with changes on how the sdif and caller_net are calculated
in these code paths in net-next.
The remaining BPF conflicts were largely about the addition of the
__bpf_md_ptr stuff in 'net' overlapping with adjustments and additions
to the relevant data structure where the MD pointer macros are used.
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell 6390 Ethernet switch family does not perform MDIO
turnaround correctly. Many hardware MDIO bus masters don't care about
this, but the bitbangging implementation in Linux does by default. Add
phy_ignore_ta_mask to the platform data so that the bitbangging code
can be told which devices are known to get TA wrong.
v2
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is sometimes necessary to instantiate a bit-banging MDIO bus as a
platform device, without the aid of device tree.
When device tree is being used, the bus is not scanned for devices,
only those devices which are in device tree are probed. Without device
tree, by default, all addresses on the bus are scanned. This may then
find a device which is not a PHY, e.g. a switch. And the switch may
have registers containing values which look like a PHY. So during the
scan, a PHY device is wrongly created.
After the bus has been registered, a search is made for
mdio_board_info structures which indicates devices on the bus, and the
driver which should be used for them. This is typically used to
instantiate Ethernet switches from platform drivers. However, if the
scanning of the bus has created a PHY device at the same location as
indicated into the board info for a switch, the switch device is not
created, since the address is already busy.
This can be avoided by setting the phy_mask of the mdio bus. This mask
prevents addresses on the bus being scanned.
v2
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the MII_ADVERTISE register is modified by the IOCTL handler,
phydev->advertising needs recalculating. Use the _mod_ variant of
mii_adv_to_linkmode_adv_t so that bits outside of the advertise
registers are not cleared.
Fixes: c0ec3c273677 ("net: phy: Convert u32 phydev->lp_advertising to linkmode")
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a _mod_ variant of mii_lpa_to_linkmode_lpa_t. Use this to fix the
genphy_read_status() where the 1G link partner features are getting
lost.
Fixes: c0ec3c273677 ("net: phy: Convert u32 phydev->lp_advertising to linkmode")
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename mii_lpa_to_linkmode_lpa_t to mii_lpa_mod_linkmode_lpa_t to
indicate it modifies the passed linkmode bitmap, without clearing any
other bits.
Also, ensure bit are clear which the lpa indicates should not be set.
Fixes: c0ec3c273677 ("net: phy: Convert u32 phydev->lp_advertising to linkmode")
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename mii_stat1000_to_linkmode_lpa_t to
mii_stat1000_mod_linkmode_lpa_t to indicate it modifies the passed
linkmode bitmap, without clearing any other bits.
Add a helper to set/clear bits in a linkmode.
Use this helper to ensure bit are clear which the stat1000 indicates
should not be set.
Fixes: c0ec3c273677 ("net: phy: Convert u32 phydev->lp_advertising to linkmode")
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts:
ef1b5bf506b1 ("net: phy: Fix not to call phy_resume() if PHY is not attached")
8c85f4b81296 ("net: phy: micrel: add toggling phy reset if PHY is not attached")
Andrew Lunn informs me that there are alternative efforts
underway to fix this more properly.
Signed-off-by: David S. Miller <davem@davemloft.net>
Logic of phy_device_create() requests PHY modules according to PHY ID
but for C45 PHYs we use different field for the IDs.
Let's also request the modules for these IDs.
Changes from v1:
- Only request C22 modules if C45 are not present (Andrew)
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Joao Pinto <joao.pinto@synopsys.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds toggling phy reset if PHY is not attached. Otherwise,
some boards (e.g. R-Car H3 Salvator-XS) cannot link up correctly if
we do the following method:
1) Kernel boots by using initramfs.
--> No open the nic, so phy_device_register() and phy_probe()
deasserts the reset.
2) Kernel enters the suspend.
--> So, keep the reset signal as deassert.
--> On R-Car Salvator-XS board, unfortunately, the board power is
turned off.
3) Kernel returns from suspend.
4) ifconfig eth0 up
--> Then, since edge signal of the reset doesn't happen,
it cannot link up.
5) ifconfig eth0 down
6) ifconfig eth0 up
--> In this case, it can link up.
Reported-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an issue that mdio_bus_phy_resume() doesn't call
phy_resume() if the PHY is not attached.
Fixes: 803dd9c77ac3 ("net: phy: avoid suspending twice a PHY")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far the two functions consider neither member eee_enabled nor
eee_active. Therefore network drivers have to do this in some kind
of glue code. I think this can be avoided.
Getting EEE parameters:
When not advertising any EEE mode, we can't consider EEE to be enabled.
Therefore interpret "EEE enabled" as "we advertise at least one EEE
mode". It's similar with "EEE active": interpret it as "EEE modes
advertised by both link partner have at least one mode in common".
Setting EEE parameters:
If eee_enabled isn't set, don't advertise any EEE mode and restart
aneg if needed to switch off EEE. If eee_enabled is set and
data->advertised is empty (e.g. because EEE was disabled), advertise
everything we support as default. This way EEE can easily switched
on/off by doing ethtool --set-eee <if> eee on/off, w/o any additional
parameters.
The changes to both functions shouldn't break any existing user.
Once the changes have been applied, at least some users can be
simplified.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently __set_phy_supported allows to add modes w/o checking whether
the PHY supports them. This is wrong, it should never add modes but
only remove modes we don't want to support.
The commit marked as fixed didn't do anything wrong, it just copied
existing functionality to the helper which is being fixed now.
Fixes: f3a6bd393c2c ("phylib: Add phy_set_max_speed helper")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently __set_phy_supported allows to add modes w/o checking whether
the PHY supports them. This is wrong, it should never add modes but
only remove modes we don't want to support.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link modes that sfp_parse_support() detects are stored in the
'modes' bitmap. There is no reason to make an exception for 1000Base-PX
or 1000Base-BX10.
Fixes: 03145864bd0f ("sfp: support 1G BiDi (eg, FiberStore SFP-GE-BX) modules")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial conflict in net/core/filter.c, a locally computed
'sdif' is now an argument to the function.
Signed-off-by: David S. Miller <davem@davemloft.net>
After switching the r8169 driver to use phylib some user reported that
their network is broken. This was caused by the genphy PHY driver being
used instead of the dedicated PHY driver for the RTL8211B. Users
reported that loading the Realtek PHY driver module upfront fixes the
issue. See also this mail thread:
https://marc.info/?t=154279781800003&r=1&w=2
The issue is quite weird and the root cause seems to be somewhere in
the base driver core. The patch works around the issue and may be
removed once the actual issue is fixed.
The Fixes tag refers to the first reported occurrence of the issue.
The issue itself may have been existing much longer and it may affect
users of other network chips as well. Users typically will recognize
this issue only if their PHY stops working when being used with the
genphy driver.
Fixes: f1e911d5d0df ("r8169: add basic phylib support")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vsc85xx_default_config function called in the vsc85xx_config_init
function which is used by VSC8530, VSC8531, VSC8540 and VSC8541 PHYs
mistakenly calls phy_read and phy_write in-between phy_select_page and
phy_restore_page.
phy_select_page and phy_restore_page actually take and release the MDIO
bus lock and phy_write and phy_read take and release the lock to write
or read to a PHY register.
Let's fix this deadlock by using phy_modify_paged which handles
correctly a read followed by a write in a non-standard page.
Fixes: 6a0bfbbe20b0 ("net: phy: mscc: migrate to phy_select/restore_page functions")
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
A more featureful support for VSC8574 was recently added to the
Microsemi (mscc.c) driver. I checked that features supported in the
Vitesse driver are also supported in the Microsemi driver.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IP101GR is a 32-pin QFN package variant of the IP101G/IP101GA
Ethernet PHY. Due to it's limited amount of pins the RXER (receive
error) and INTR32 (interrupt) functions share pin 21.
By default the PHY is configured to output the "receive error" status on
pin 21. Depending on the board layout and requirements we may want to
re-configure the PHY to output the interrupt signal there.
The mode of pin 21 can be configured in the "Digital I/O Specific
Control Register" (register 29), bit 2:
- 0 = RXER function
- 1 = INTR(32) function
Depending on the devicetree configuration we will now:
- change the mode to either ther RXER or INTR32 function
- keep the SEL_INTR32 value set by the bootloader (default) if no
configuration is provided (to ensure that we're not breaking existing
boards)
- error out if conflicting configuration is given (RXER and INTR32 mode
are enabled at the same time)
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IP101A_G_IRQ_CONF_STATUS register has bits to detect which
interrupts have fired. Implement the .did_interrupt callback to let the
PHY core know whether the interrupt was for this specific PHY.
This is useful for debugging interrupt problems with 32-pin IP101GR PHYs
where the interrupt line is shared with the RX_ERR (receive error
status) signal. The default values are:
- RX_ERR is enabled by default (LOW means that there is no receive
error)
- the PHY's interrupt line is configured "active low" by default
Without any additional changes there is a flood of interrupts if the
RX_ERR/INTR32 signal is configured in RX_ERR mode (which is the
default). Having a did_interrupt ensures that the PHY core returns
IRQ_NONE instead of endlessly triggering the PHY state machine.
Additionally the kernel will report this after a while:
irq 28: nobody cared (try booting with the "irqpoll" option)
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The datasheet uses the name "All Mask" for this bit. Change the name of
our #define to be consistent with the datasheet. While here also replace
the tab between the #define and IP101A_G_IRQ_ALL_MASK with a space.
No functional changes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
