The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The CEC pin framework is affected by NTP daemons speeding up or slowing
down the system clock. Document this and explain how to fix this for
chronyd.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The valid_la boolean is used to check if the destination logical
address is either 15 (broadcast) or our logical address. If it is
for another logical address, then only adapters that have the
CEC_CAP_MONITOR_ALL capability can pass it on.
However, it is also used to do more detailed validity checks,
such as whether the message was broadcast when it should have been
directed, or vice versa, in which case the message must be ignored
according to the spec. But that should not apply to monitoring.
Add a new bool that just checks the LA and nothing else.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
ctx->vpu_dst_fmt is no more initialized before calling hantro_try_fmt()
so assigne it to vpu_fmt led to crash the kernel.
Like for decoder case use 'fmt' as format for encoder and clean up
the code.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: db6f68b51e5c ("media: verisilicon: Do not set context src/dst formats in reset functions")
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Structures passed to subdev pad operations are all zero-initialized when
declaring variables. In most cases, this is done with designated
initializers to initialize some of the fields to specific values, but in
a minority of cases the structures are zero-initialized by assigning
them to '{ 0 }' or '{ }'.
Improve coding style consistency by using designated initializers where
possible, always initializing the 'which' field.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Structures passed to subdev pad operations are all zero-initialized, but
not always with the same kind of code constructs. While most drivers
used designated initializers, which zero all the fields that are not
specified, when declaring variables, some use memset(). Those two
methods lead to the same end result, and, depending on compiler
optimizations, may even be completely equivalent, but they're not
consistent.
Improve coding style consistency by using designated initializers
instead of calling memset(). Where applicable, also move the variables
to inner scopes of for loops to ensure correct initialization in all
iterations.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Lad Prabhakar <prabhakar.csengg@gmail.com> # For am437x
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Several drivers call subdev pad operations, passing structures that are
not fully zeroed. While the drivers initialize the fields they care
about explicitly, this results in reserved fields having uninitialized
values. Future kernel API changes that make use of those fields thus
risk breaking proper driver operation in ways that could be hard to
detect.
To avoid this, make the code more robust by zero-initializing all the
structures passed to subdev pad operation. Maintain a consistent coding
style by preferring designated initializers (which zero-initialize all
the fields that are not specified) over memset() where possible, and
make variable declarations local to inner scopes where applicable. One
notable exception to this rule is in the ipu3 driver, where a memset()
is needed as the structure is not a local variable but a function
parameter provided by the caller.
Not all fields of those structures can be initialized when declaring the
variables, as the values for those fields are computed later in the
code. Initialize the 'which' field in all cases, and other fields when
the variable declaration is so close to the v4l2_subdev_call() call that
it keeps all the context easily visible when reading the code, to avoid
hindering readability.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org> # For vimc
Reviewed-by: Lad Prabhakar <prabhakar.csengg@gmail.com> # For am437x
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de> # For drivers/staging/media/imx/
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Variable initialization code in notify_src_chg() is incorrectly
indented. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Commit 0d346d2a6f54 ("media: v4l2-subdev: add subdev-wide state struct")
applied a large media tree-wide change produced by coccinelle. It was so
large that a set of identical indentation issues went unnoticed during
review. Fix them.
While at it, and because it's easy to review both changes together, add
a trailing comma for the last (and only) struct member initialization of
the related structures, to avoid future changes should new fields need
to be initialized.
Fixes: 0d346d2a6f54 ("media: v4l2-subdev: add subdev-wide state struct")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
According to msm_media_info.h the correct alignment
for the stride of P010 buffers is 128.
Signed-off-by: Fritz Koenig <frkoenig@chromium.org>
Reviewed-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Signed-off-by: Stanimir Varbanov <stanimir.k.varbanov@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Currently QP range set from client is not communicated to video firmware.
Add support for the QP range HFI to set the same to firmware.
Signed-off-by: Viswanath Boma <quic_vboma@quicinc.com>
Signed-off-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Signed-off-by: Stanimir Varbanov <stanimir.k.varbanov@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Commit 9593126dae3e ("media: venus: Add a handling of QC08C compressed
format") and commit cef92b14e653 ("media: venus: Add a handling of QC10C
compressed format") added support for the QC08C and QC10C compressed
formats respectively.
But these also caused a regression, because the new formats where added
at the beginning of the vdec_formats[] array and the vdec_inst_init()
function sets the default format output and capture using fixed indexes
of that array:
static void vdec_inst_init(struct venus_inst *inst)
{
...
inst->fmt_out = &vdec_formats[8];
inst->fmt_cap = &vdec_formats[0];
...
}
Since now V4L2_PIX_FMT_NV12 is not the first entry in the array anymore,
the default capture format is not set to that as it was done before.
Both commits changed the first index to keep inst->fmt_out default format
set to V4L2_PIX_FMT_H264, but did not update the latter to keep .fmt_out
default format set to V4L2_PIX_FMT_NV12.
Rather than updating the index to the current V4L2_PIX_FMT_NV12 position,
let's reorder the entries so that this format is the first entry again.
This would also make VIDIOC_ENUM_FMT report the V4L2_PIX_FMT_NV12 format
with an index 0 as it did before the QC08C and QC10C formats were added.
Fixes: 9593126dae3e ("media: venus: Add a handling of QC08C compressed format")
Fixes: cef92b14e653 ("media: venus: Add a handling of QC10C compressed format")
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Stanimir Varbanov <stanimir.k.varbanov@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Aligned the mismatch of persist1 and scratch1 buffer calculation,
as per the firmware requirements.
Signed-off-by: Vikash Garodia <vgarodia@qti.qualcomm.com>
Signed-off-by: Viswanath Boma <quic_vboma@quicinc.com>
Tested-by: Nathan Hebert <nhebert@chromium.org>
Signed-off-by: Stanimir Varbanov <stanimir.k.varbanov@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The decoder driver should clear the last_buffer_dequeued flag of the
capture queue upon receiving V4L2_DEC_CMD_START.
The last_buffer_dequeued flag is set upon receiving EOS (which always
happens upon receiving V4L2_DEC_CMD_STOP).
Without this patch, after issuing the V4L2_DEC_CMD_STOP and
V4L2_DEC_CMD_START, the vb2_dqbuf() function will always fail, even if
the buffers are completed by the hardware.
Fixes: beac82904a87 ("media: venus: make decoder compliant with stateful codec API")
Signed-off-by: Michał Krawczyk <mk@semihalf.com>
Signed-off-by: Stanimir Varbanov <stanimir.k.varbanov@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The driver was intended from the start to be a wake-up source for the
system, however due to the absence of a suitable call to
device_set_wakeup_capable(), the device_may_wakeup() call used to decide
whether to enable the GPIO interrupt as a wake-up source would never
happen. Lookup the DT standard "wakeup-source" property and call
device_init_wakeup() to ensure the device is flagged as being wakeup
capable.
Reported-by: Matthew Lear <matthew.lear@broadcom.com>
Fixes: fd0f6851eb46 ("[media] rc: Add support for GPIO based IR Receiver driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The GPIO IR receiver can be used as a wake-up source for the system,
document that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Also dev_err_probe message require a trailing \n.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Document the firmware file names for CCS static data for CCS, SMIA++ and
SMIA devices.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
MIPI CCS uses a 16-bit MIPI manufacturer identifier for firmware filenames
compared to older 8-bit identifier used by SMIA. The requested firmware
files used the MIPI manufacturer ID even for SMIA compliant devices,
effectively making the manufacturer ID 0.
While CCS static data is a feature of CCS 1.1, it has no hardware
dependencies. Making this feature available for SMIA devices helps adding
support for them and avoids requesting ill-generated CCS static data file
names. The files are named as:
ccs/smiapp-module-vv-mmmm-rrrr.fw,
ccs/smiapp-sensor-vv-mmmm-rr.fw and
ccs/smia-sensor-vv-mmmm-rr.fw
where vv is the manufacturer ID, mmmm is the model ID and rr or rrrr is
the revision number.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Some modules don't have any model identification information in the
register address space. The driver as a SMIA++ driver attempted to use
sensor information in this case. This workaround is definitely not for CCS
devices.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Read 16-bit sensor revision number if the 8-bit register has value 0.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
No longer mirror flipping controls if the sensor is mounted upside down.
This way the behaviour of the flipping controls and rotation of the sensor
are aligned with the rest of the drivers.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The "rotation" fwnode device property is intended to allow specify the
sensor's physical mounting rotation, so that it can be exposed through
the read-only V4L2_CID_CAMERA_SENSOR_ROTATION control and applications
can decide how to compensate for that.
The imx258 driver has read-only VFLIP and HFLIP enabled, resulting in
a 180 degrees image rotation being produced by the sensor. But this
doesn't imply that the physical mounting rotation should match the
driver's implementation.
Now that the driver registers V4L2_CID_CAMERA_SENSOR_ROTATION
and V4L2_CID_HFLIP/VFLIP correctly, userspace has all the required
information to handle the rotation correctly, hence it is not necessary
to require the 'rotation' property to be fixed to 180 degrees in DTS.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Register controls for V4L2_CID_HFLIP and V4L2_CID_VFLIP.
The controls are registered as read-only and enabled by default, as the
driver embeds a 180 degrees rotation in its programming sequences and
only supports that mode of operations.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Dongchun's e-mail mailbox is no longer available, assign the
maintainership to myself.
The following message to <dongchun.zhu@mediatek.com> was
undeliverable. The reason for the problem: 5.1.0 - Unknown address
error 550-'Relaying mail to dongchun.zhu@mediatek.com is not
allowed'
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Dongchun's e-mail address is no longer valid, assign the ov8856 driver to
myself.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add more camera sensors into the supported camera sensors list
to make cio2-bridge to support more camera sensors.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Adding additional cropped 2592x1444 resolution
for QHD output from Hi556 sensor
Also implement the get_selection pad operation for the Hi556 sensor driver.
The supported targets report the sensor's native size, the crop default
rectangle and the crop rectangle.
Signed-off-by: Jim Lai <jim.lai@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The struct venus_format does not have a "opp_table" field.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
R-Car H3 ES1.* was only available to an internal development group and
needed a lot of quirks and workarounds. These become a maintenance
burden now, so our development group decided to remove upstream support
and disable booting for this SoC. Public users only have ES2 onwards.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
R-Car H3 ES1.* was only available to an internal development group and
needed a lot of quirks and workarounds. These become a maintenance
burden now, so our development group decided to remove upstream support
and disable booting for this SoC. Public users only have ES2 onwards.
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
R-Car H3 ES1.* was only available to an internal development group and
needed a lot of quirks and workarounds. These become a maintenance
burden now, so our development group decided to remove upstream support
and disable booting for this SoC. Public users only have ES2 onwards.
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties. As
part of this, convert of_get_property/of_find_property calls to the
recently added of_property_present() helper when we just want to test
for presence of a property and nothing more.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
In current cio2-bridge, it is using the hid name to register software
node and software node will create kobject and sysfs entry according to
the node name, if there are multiple sensors and VCMs which are sharing
same HID name, it will cause the software nodes registration failure:
sysfs: cannot create duplicate filename '/kernel/software_nodes/dw9714'
...
Call Trace:
software_node_register_nodes
cio2_bridge_init
...
kobject_add_internal failed for dw9714 with -EEXIST,
don't try to register things with the same name in the same directory.
One solution is appending the sensor link(Mipi Port) in SSDB as suffix
of the node name to fix this problem.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The v4l2_create_fwnode_links_to_pad() helper requires the sink pad
passed to it to belong to a subdev. This requirement can be lifted
easily. Make the function usable for non-subdev sinks, which allows
using it with video_device sinks.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The ADV7604, ADV7611 and ADV7612 software manuals document the CP_HUE
value differently:
- For ADV7604 and ADV7611, the hue is specified as an unsigned 8-bit
value, and calculated as
(CP_HUE[7:0] * 180) / 256 - 90
with the range set to [-90°, 90°]. Additionally, the values 0x00, 0x0f
and 0xff are documented as corresponding to -90°, 0° and 90°
respectively.
- For ADV7612, the hue is specified as a signed 8-bit value in the range
[0°, 360°[ without any formula. Additionally, the value 0x00 is
documented as corresponding to 0°.
The ADV7604 and ADV7611 documentation is clearly wrong as the example
values don't correspond to the formula. Furthermore, the [-90°, 90°]
range seems incorrect as it would cover only half of the hue space.
The ADV7612 documentation is better, although the range should likely be
[-180°, 180°[ if the value is signed. Given that the values wrap around,
this makes no difference in practice.
The hue values have been verified on ADV7612 to follow the
documentation. There is a high chance they do as well on ADV7604 and
ADV7611.
In any case, all software manuals document the register as 8-bit, so the
current range of the V4L2 hue control [0, 128] is not correct. Expand it
to cover the full 8-bit space, using unsigned values to avoid breaking
any application that may rely on 128 being a valid value.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The video adjustments (contrast, brightness, saturation and hue) are
ignored by default by the device when the VID_ADJ_EN bit is clear. The
corresponding V4L2 controls exposed by the drivers have thus no effect.
Fix this by setting the VID_ADJ_EN bit.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
In some setups XSHUTDOWN is connected to DOVDD when it's unused,
therefore treat the reset gpio as optional.
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Convert the text-based dt-bindings to yaml.
Changes from original txt:
* Take wording for various properties from other yaml bindings, this
removes e.g. volt amount from schema since it isn't really relevant
and the datasheet is a better source.
* Don't make reset-gpios a required property since it can be tied to
DOVDD instead.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
[Sakari Ailus: bump the maxItems for data-lanes to two]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
With the upcoming conversion of ov2685 to dt-schema let's complete the
example so validation succeeds. At the same time fix the indentation of
the port node in this example.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
In the file mc-device.c, the function
media_device_register_entity_notify() does not need to have the
__must_check attribute since it returns only a value of 0.
Therefore, we can remove this attribute and change the function's
return type.
Signed-off-by: Jason Kim <sukbeom.kim@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
hi846_init_controls doesn't clean the allocated ctrl_hdlr
in case there is a failure, which causes memleak. Add
v4l2_ctrl_handler_free to free the resource properly.
Fixes: e8c0882685f9 ("media: i2c: add driver for the SK Hynix Hi-846 8M pixel camera")
Signed-off-by: Wei Chen <harperchen1110@gmail.com>
Reviewed-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
It the device is probed in non-zero ACPI D state, the module
identification is delayed until the first streamon.
The module identification has two parts: deviceID and version. To rea
the version we have to enable OTP read. This cannot be done during
streamon, becase it modifies REG_MODE_SELECT.
Since the driver has the same behaviour for all the module versions, do
not read the module version from the sensor's OTP.
Cc: stable@vger.kernel.org
Fixes: 0e014f1a8d54 ("media: ov8856: support device probe in non-zero ACPI D state")
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cleanup bindings dropping unneeded quotes. Once all these are fixed,
checking for this can be enabled in yamllint.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Joe Tessler <jrt@google.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de> #rockchip
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
[Sakari Ailus: Drop changes for files in which they had been done already]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Use devm_clk_get_optional() instead of hand writing it.
This saves some loC and improves the semantic.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
When an async notifier is unregistered, the async sub-devices in the
notifier's done list will disappear with the notifier. However this is
currently also done to the sub-notifiers that remain registered. Their
sub-devices only need to be unbound while the async sub-devices themselves
need to be returned to the sub-notifier's waiting list. Do this now.
Fixes: 2cab00bb076b ("media: v4l: async: Allow binding notifiers to sub-devices")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The imx_media_of_add_csi() function is only called in its compilation
unit. Make it static and don't export it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
