With this port schedule:
tc qdisc replace dev $send_if parent root handle 100 taprio \
num_tc 8 queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 \
map 0 1 2 3 4 5 6 7 \
base-time 0 cycle-time 10000 \
sched-entry S 01 1250 \
sched-entry S 02 1250 \
sched-entry S 04 1250 \
sched-entry S 08 1250 \
sched-entry S 10 1250 \
sched-entry S 20 1250 \
sched-entry S 40 1250 \
sched-entry S 80 1250 \
flags 2
ptp4l would fail to take TX timestamps of Pdelay_Resp messages like this:
increasing tx_timestamp_timeout may correct this issue, but it is likely caused by a driver bug
ptp4l[4134.168]: port 2: send peer delay response failed
It turns out that the driver can't take their TX timestamps because it
can't transmit them in the first place. And there's nothing special
about the Pdelay_Resp packets - they're just regular 68 byte packets.
But with this taprio configuration, the switch would refuse to send even
the ETH_ZLEN minimum packet size.
This should have definitely not been the case. When applying the taprio
config, the driver prints:
mscc_felix 0000:00:00.5: port 0 tc 0 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 1 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 2 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 3 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 4 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 5 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 6 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 7 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
and thus, everything under 132 bytes - ETH_FCS_LEN should have been sent
without problems. Yet it's not.
For the forwarding path, the configuration is fine, yet packets injected
from Linux get stuck with this schedule no matter what.
The first hint that the static guard bands are the cause of the problem
is that reverting Michael Walle's commit 297c4de6f7 ("net: dsa: felix:
re-enable TAS guard band mode") made things work. It must be that the
guard bands are calculated incorrectly.
I remembered that there is a magic constant in the driver, set to 33 ns
for no logical reason other than experimentation, which says "never let
the static guard bands get so large as to leave less than this amount of
remaining space in the time slot, because the queue system will refuse
to schedule packets otherwise, and they will get stuck". I had a hunch
that my previous experimentally-determined value was only good for
packets coming from the forwarding path, and that the CPU injection path
needed more.
I came to the new value of 35 ns through binary search, after seeing
that with 544 ns (the bit time required to send the Pdelay_Resp packet
at gigabit) it works. Again, this is purely experimental, there's no
logic and the manual doesn't say anything.
The new driver prints for this schedule look like this:
mscc_felix 0000:00:00.5: port 0 tc 0 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 1 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 2 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 3 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 4 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 5 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 6 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 7 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
So yes, the maximum MTU is now even smaller by 1 byte than before.
This is maybe counter-intuitive, but makes more sense with a diagram of
one time slot.
Before:
Gate open Gate close
| |
v 1250 ns total time slot duration v
<---------------------------------------------------->
<----><---------------------------------------------->
33 ns 1217 ns static guard band
useful
Gate open Gate close
| |
v 1250 ns total time slot duration v
<---------------------------------------------------->
<-----><--------------------------------------------->
35 ns 1215 ns static guard band
useful
The static guard band implemented by this switch hardware directly
determines the maximum allowable MTU for that traffic class. The larger
it is, the earlier the switch will stop scheduling frames for
transmission, because otherwise they might overrun the gate close time
(and avoiding that is the entire purpose of Michael's patch).
So, we now have guard bands smaller by 2 ns, thus, in this particular
case, we lose a byte of the maximum MTU.
Fixes: 11afdc6526 ("net: dsa: felix: tc-taprio intervals smaller than MTU should send at least one packet")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Michael Walle <mwalle@kernel.org>
Link: https://patch.msgid.link/20241210132640.3426788-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
LAN9646 switch is a 6-port switch with functions like KSZ9897. It has
4 internal PHYs and 1 SGMII port. The chip id read from hardware is
same as KSZ9477, so software driver needs to create a new chip id and
group allowable functions under its chip data structure to
differentiate the product.
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Link: https://patch.msgid.link/20241109015705.82685-3-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
qca8k_phy_eth_command() is used to probe the child MDIO bus while the
parent MDIO is locked. This causes lockdep splat, reporting a possible
deadlock. It is not an actually deadlock, because different locks are
used. By making use of mutex_lock_nested() we can avoid this false
positive.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241110175955.3053664-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce ksz_parse_dt_phy_config() to validate and parse PHY
configuration from the device tree for KSZ switches. This function
ensures proper setup of internal PHYs by checking `phy-handle`
properties, verifying expected PHY IDs, and handling parent node
mismatches. Sets the PHY mask on the MII bus if validation is
successful. Returns -EINVAL on configuration errors.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20241106075942.1636998-7-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement side MDIO channel support for LAN937x switches, providing an
alternative to SPI for PHY management alongside existing SPI-based
switch configuration. This is needed to reduce SPI load, as SPI can be
relatively expensive for small packets compared to MDIO support.
Also, implemented static mappings for PHY addresses for various LAN937x
models to support different internal PHY configurations. Since the PHY
address mappings are not equal to the port indexes, this patch also
provides PHY address calculation based on hardware strapping
configuration.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241106075942.1636998-6-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace repeated cleanup code with a single error path using a label.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241106075942.1636998-5-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for accessing PHYs via a side MDIO interface in LAN937x
switches. The existing code already supports accessing PHYs via main
management interfaces, which can be SPI, I2C, or MDIO, depending on the
chip variant. This patch enables using a side MDIO bus, where SPI is
used for the main switch configuration and MDIO for managing the
integrated PHYs. On LAN937x, this is optional, allowing them to operate
in both configurations: SPI only, or SPI + MDIO. Typically, the SPI
interface is used for switch configuration, while MDIO handles PHY
management.
Additionally, update interrupt controller code to support non-linear
port to PHY address mapping, enabling correct interrupt handling for
configurations where PHY addresses do not directly correspond to port
indexes. This change ensures that the interrupt mechanism properly
aligns with the new, flexible PHY address mappings introduced by side
MDIO support.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241106075942.1636998-4-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce port_setup_tc callback in mt7530 dsa driver in order to enable
dsa ports rate shaping via hw Token Bucket Filter (TBF) for hw switched
traffic.
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241031-mt7530-tc-offload-v2-1-cb242ad954a0@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
These are the preferred way to copy ethtool strings.
Avoids incrementing pointers all over the place.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
(for hellcreek driver)
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Link: https://patch.msgid.link/20241028044828.1639668-1-rosenp@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
'ports_fwnode' is initialized via device_get_named_child_node(), which
requires a call to fwnode_handle_put() when the variable is no longer
required to avoid leaking memory.
Add the missing fwnode_handle_put() after 'ports_fwnode' has been used
and is no longer required.
Fixes: 94a2a84f5e ("net: dsa: mv88e6xxx: Support LED control")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MV88E6393X family of devices can run its cycle counter off
an internal 250MHz clock instead of an external 125MHz one.
Add support for this cycle counter period by adding another set
of coefficients and lowering the periodic cycle counter read interval
to compensate for faster overflows at the increased frequency.
Otherwise, the PHC runs at 2x real time in userspace and cannot be
synchronized.
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Signed-off-by: Shenghao Yang <me@shenghaoyang.info>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Instead of relying on a fixed mapping of hardware family to cycle
counter frequency, pull this information from the
MV88E6XXX_TAI_CLOCK_PERIOD register.
This lets us support switches whose cycle counter frequencies depend on
board design.
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shenghao Yang <me@shenghaoyang.info>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Instead of having them as individual fields in ptp_ops, wrap the
coefficients in a separate struct so they can be referenced together.
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Signed-off-by: Shenghao Yang <me@shenghaoyang.info>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The well-known errata regarding EEE not being functional on various KSZ
switches has been refactored a few times. Recently the refactoring has
excluded several switches that the errata should also apply to.
Disable EEE for additional switches with this errata and provide
additional comments referring to the public errata document.
The original workaround for the errata was applied with a register
write to manually disable the EEE feature in MMD 7:60 which was being
applied for KSZ9477/KSZ9897/KSZ9567 switch ID's.
Then came commit 26dd2974c5 ("net: phy: micrel: Move KSZ9477 errata
fixes to PHY driver") and commit 6068e6d7ba ("net: dsa: microchip:
remove KSZ9477 PHY errata handling") which moved the errata from the
switch driver to the PHY driver but only for PHY_ID_KSZ9477 (PHY ID)
however that PHY code was dead code because an entry was never added
for PHY_ID_KSZ9477 via MODULE_DEVICE_TABLE.
This was apparently realized much later and commit 54a4e5c163 ("net:
phy: micrel: add Microchip KSZ 9477 to the device table") added the
PHY_ID_KSZ9477 to the PHY driver but as the errata was only being
applied to PHY_ID_KSZ9477 it's not completely clear what switches
that relates to.
Later commit 6149db4997 ("net: phy: micrel: fix KSZ9477 PHY issues
after suspend/resume") breaks this again for all but KSZ9897 by only
applying the errata for that PHY ID.
Following that this was affected with commit 08c6d8bae48c("net: phy:
Provide Module 4 KSZ9477 errata (DS80000754C)") which removes
the blatant register write to MMD 7:60 and replaces it by
setting phydev->eee_broken_modes = -1 so that the generic phy-c45 code
disables EEE but this is only done for the KSZ9477_CHIP_ID (Switch ID).
Lastly commit 0411f73c13 ("net: dsa: microchip: disable EEE for
KSZ8567/KSZ9567/KSZ9896/KSZ9897.") adds some additional switches
that were missing to the errata due to the previous changes.
This commit adds an additional set of switches.
Fixes: 0411f73c13 ("net: dsa: microchip: disable EEE for KSZ8567/KSZ9567/KSZ9896/KSZ9897.")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20241018160658.781564-1-tharvey@gateworks.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Cross-merge networking fixes after downstream PR (net-6.12-rc4).
Conflicts:
107a034d5c ("net/mlx5: qos: Store rate groups in a qos domain")
1da9cfd6c4 ("net/mlx5: Unregister notifier on eswitch init failure")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
mv88e6393x_port_set_policy doesn't correctly shift the ptr value when
converting the policy format between the old and new styles, so the
target register ends up with the ptr being written over the data bits.
Shift the pointer to align with the format expected by
mv88e6393x_port_policy_write().
Fixes: 6584b26020 ("net: dsa: mv88e6xxx: implement .port_set_policy for Amethyst")
Signed-off-by: Peter Rashleigh <peter@rashleigh.ca>
Reviewed-by: Simon Horman <horms@kernel.org>
Message-ID: <20241016040822.3917-1-peter@rashleigh.ca>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Rather than returning an EOPNOTSUPP error pointer when the switch
has no support for PCS, return NULL to indicate that no PCS is
required.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Similar to the situation described for sja1105 in commit 1f9fc48fd3
("net: dsa: sja1105: fix reception from VLAN-unaware bridges"), the
vsc73xx driver uses tag_8021q and doesn't need the ds->untag_bridge_pvid
request. In fact, this option breaks packet reception.
The ds->untag_bridge_pvid option strips VLANs from packets received on
VLAN-unaware bridge ports. But those VLANs should already be stripped
by tag_vsc73xx_8021q.c as part of vsc73xx_rcv() - they are not VLANs in
VLAN-unaware mode, but DSA tags. Thus, dsa_software_vlan_untag() tries
to untag a VLAN that doesn't exist, corrupting the packet.
Fixes: 93e4649efa ("net: dsa: provide a software untagging function on RX for VLAN-aware bridges")
Tested-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patch.msgid.link/20241014153041.1110364-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
According to the Marvell datasheet the 88E6361 has two VTU pages
(4k VIDs per page) so the max_vid should be 8191, not 4095.
In the current implementation mv88e6xxx_vtu_walk() gives unexpected
results because of this error. I verified that mv88e6xxx_vtu_walk()
works correctly on the MV88E6361 with this patch in place.
Fixes: 12899f2998 ("net: dsa: mv88e6xxx: enable support for 88E6361 switch")
Signed-off-by: Peter Rashleigh <peter@rashleigh.ca>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241014204342.5852-1-peter@rashleigh.ca
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Prior to this patch ksz_ptp_msg_irq_setup() uses snprintf() to copy
strings. It does so by passing strings as the format argument of
snprintf(). This appears to be safe, due to the absence of format
specifiers in the strings, which are declared within the same function.
But nonetheless GCC 14 warns about it:
.../ksz_ptp.c:1109:55: warning: format string is not a string literal (potentially insecure) [-Wformat-security]
1109 | snprintf(ptpmsg_irq->name, sizeof(ptpmsg_irq->name), name[n]);
| ^~~~~~~
.../ksz_ptp.c:1109:55: note: treat the string as an argument to avoid this
1109 | snprintf(ptpmsg_irq->name, sizeof(ptpmsg_irq->name), name[n]);
| ^
| "%s",
As what we are really dealing with here is a string copy, it seems make
sense to use a function designed for this purpose. In this case null
padding is not required, so strscpy is appropriate. And as the
destination is an array of fixed size, the 2-argument variant may be used.
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241014-string-thing-v2-1-b9b29625060a@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The err value in mv88e6xxx_region_atu_snapshot is now potentially
uninitialised on return. Initialise err as 0.
Fixes: ada5c3229b ("net: dsa: mv88e6xxx: Add FID map cache")
Signed-off-by: Aryan Srivastava <aryan.srivastava@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241009212319.1045176-1-aryan.srivastava@alliedtelesis.co.nz
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a cached FID bitmap. This mitigates the need to walk all VTU entries
to find the next free FID.
When flushing the VTU (during init), zero the FID bitmap. Use and
manipulate this bitmap from now on, instead of reading HW for the FID
map.
The repeated VTU walks are costly and can take ~40 mins if ~4000 vlans
are added. Caching the FID map reduces this time to <2 mins.
Signed-off-by: Aryan Srivastava <aryan.srivastava@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241006212905.3142976-1-aryan.srivastava@alliedtelesis.co.nz
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All modern chips support and need the 10_100 bit set for supporting jumbo
frames on 10/100 ports, so instead of enabling it only for 583XX enable
it for everything except bcm63xx, where the bit is writeable, but does
nothing.
Tested on BCM53115, where jumbo frames were dropped at 10/100 speeds
without the bit set.
Fixes: 6ae5834b98 ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
While BCM5325/5365 do not support jumbo frames, they do support slightly
oversized frames, so do not error out if requesting a supported MTU for
them.
Fixes: 6ae5834b98 ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
BCM5325/BCM5365 do not support jumbo frames, so we should not report a
jumbo frame mtu for them. But they do support so called "oversized"
frames up to 1536 bytes long by default, so report an appropriate MTU.
Fixes: 6ae5834b98 ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
JMS_MAX_SIZE is the ethernet frame length, not the MTU, which is payload
without ethernet headers.
According to the datasheets maximum supported frame length for most
gigabyte swithes is 9720 bytes, so convert that to the expected MTU when
using VLAN tagged frames.
Fixes: 6ae5834b98 ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
JMS_MIN_SIZE is the full ethernet frame length, while mtu is just the
data payload size. Comparing these two meant that mtus between 1500 and
1518 did not trigger enabling jumbo frames.
So instead compare the set mtu ETH_DATA_LEN, which is equal to
JMS_MIN_SIZE - ETH_HLEN - ETH_FCS_LEN;
Also do a check that the requested mtu is actually greater than the
minimum length, else we do not need to enable jumbo frames.
In practice this only introduced a very small range of mtus that did not
work properly. Newer chips allow 2000 byte large frames by default, and
older chips allow 1536 bytes long, which is equivalent to an mtu of
1514. So effectivly only mtus of 1515~1517 were broken.
Fixes: 6ae5834b98 ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Accessing device registers seems to be not reliable, the chip
revision is sometimes detected wrongly (0 instead of expected 1).
Ensure that the chip reset is performed via reset GPIO and then
wait for 'Device Ready' status in HW_CFG register before doing
any register initializations.
Cc: stable@vger.kernel.org
Fixes: a1292595e0 ("net: dsa: add new DSA switch driver for the SMSC-LAN9303")
Signed-off-by: Anatolij Gustschin <agust@denx.de>
[alex: reworked using read_poll_timeout()]
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/20241004113655.3436296-1-alexander.sverdlin@siemens.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/net/dsa to use .remove(),
with the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/36da477cb9fa0bffec32d50c2cf3d18e94a0e7e3.1727949050.git.u.kleine-koenig@baylibre.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The SF2 crossbar register is a packed bitfield, giving the index of the
external port selected for each of the internal ports. On BCM4908 (the
only currently-supported switch family with a crossbar), there are 2
internal ports and 3 external ports, so there are 2 bits per internal
port.
The driver currently conflates the "bits per port" and "number of ports"
concepts, lumping both into the `num_crossbar_int_ports` field. Since it
is currently only possible for either of these counts to have a value of
2, there is no behavioral error resulting from this situation for now.
Make the code more readable (and support the future possibility of
larger crossbars) by adding a `num_crossbar_ext_bits` field to represent
the "bits per port" count and relying on this where appropriate instead.
Signed-off-by: Sam Edwards <CFSworks@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20241003212301.1339647-1-CFSworks@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This adds control over the hardware LEDs in the Marvell
MV88E6xxx DSA switch and enables it for MV88E6352.
This fixes an imminent problem on the Inteno XG6846 which
has a WAN LED that simply do not work with hardware
defaults: driver amendment is necessary.
The patch is modeled after Christian Marangis LED support
code for the QCA8k DSA switch, I got help with the register
definitions from Tim Harvey.
After this patch it is possible to activate hardware link
indication like this (or with a similar script):
cd /sys/class/leds/Marvell\ 88E6352:05:00:green:wan/
echo netdev > trigger
echo 1 > link
This makes the green link indicator come up on any link
speed. It is also possible to be more elaborate, like this:
cd /sys/class/leds/Marvell\ 88E6352:05:00:green:wan/
echo netdev > trigger
echo 1 > link_1000
cd /sys/class/leds/Marvell\ 88E6352:05:01:amber:wan/
echo netdev > trigger
echo 1 > link_100
Making the green LED come on for a gigabit link and the
amber LED come on for a 100 mbit link.
Each port has 2 LED slots (the hardware may use just one or
none) and the hardware triggers are specified in four bits per
LED, and some of the hardware triggers are only available on the
SFP (fiber) uplink. The restrictions are described in the
port.h header file where the registers are described. For
example, selector 1 set for LED 1 on port 5 or 6 will indicate
Fiber 1000 (gigabit) and activity with a blinking LED, but
ONLY for an SFP connection. If port 5/6 is used with something
not SFP, this selector is a noop: something else need to be
selected.
After the previous series rewriting the MV88E6xxx DT
bindings to use YAML a "leds" subnode is already valid
for each port, in my scratch device tree it looks like
this:
leds {
#address-cells = <1>;
#size-cells = <0>;
led@0 {
reg = <0>;
color = <LED_COLOR_ID_GREEN>;
function = LED_FUNCTION_LAN;
default-state = "off";
linux,default-trigger = "netdev";
};
led@1 {
reg = <1>;
color = <LED_COLOR_ID_AMBER>;
function = LED_FUNCTION_LAN;
default-state = "off";
};
};
This DT config is not yet configuring everything: when the netdev
default trigger is assigned the hw acceleration callbacks are
not called, and there is no way to set the netdev sub-trigger
type (such as link_1000) from the device tree, such as if you want
a gigabit link indicator. This has to be done from userspace at
this point.
We add LED operations to all switches in the 6352 family:
6172, 6176, 6240 and 6352.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241001-mv88e6xxx-leds-v4-1-cc11c4f49b18@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The blamed commit introduced an unexpected regression in the sja1105
driver. Packets from VLAN-unaware bridge ports get received correctly,
but the protocol stack can't seem to decode them properly.
For ds->untag_bridge_pvid users (thus also sja1105), the blamed commit
did introduce a functional change: dsa_switch_rcv() used to call
dsa_untag_bridge_pvid(), which looked like this:
err = br_vlan_get_proto(br, &proto);
if (err)
return skb;
/* Move VLAN tag from data to hwaccel */
if (!skb_vlan_tag_present(skb) && skb->protocol == htons(proto)) {
skb = skb_vlan_untag(skb);
if (!skb)
return NULL;
}
and now it calls dsa_software_vlan_untag() which has just this:
/* Move VLAN tag from data to hwaccel */
if (!skb_vlan_tag_present(skb)) {
skb = skb_vlan_untag(skb);
if (!skb)
return NULL;
}
thus lacks any skb->protocol == bridge VLAN protocol check. That check
is deferred until a later check for skb->vlan_proto (in the hwaccel area).
The new code is problematic because, for VLAN-untagged packets,
skb_vlan_untag() blindly takes the 4 bytes starting with the EtherType
and turns them into a hwaccel VLAN tag. This is what breaks the protocol
stack.
It would be tempting to "make it work as before" and only call
skb_vlan_untag() for those packets with the skb->protocol actually
representing a VLAN.
But the premise of the newly introduced dsa_software_vlan_untag() core
function is not wrong. Drivers set ds->untag_bridge_pvid or
ds->untag_vlan_aware_bridge_pvid presumably because they send all
traffic to the CPU reception path as VLAN-tagged. So why should we spend
any additional CPU cycles assuming that the packet may be VLAN-untagged?
And why does the sja1105 driver opt into ds->untag_bridge_pvid if it
doesn't always deliver packets to the CPU as VLAN-tagged?
The answer to the latter question is indeed more interesting: it doesn't
need to. This got done in commit 884be12f85 ("net: dsa: sja1105: add
support for imprecise RX"), because I thought it would be needed, but I
didn't realize that it doesn't actually make a difference.
As explained in the commit message of the blamed patch, ds->untag_bridge_pvid
only makes a difference in the VLAN-untagged receive path of a bridge port.
However, in that operating mode, tag_sja1105.c makes use of VLAN tags
with the ETH_P_SJA1105 TPID, and it decodes and consumes these VLAN tags
as if they were DSA tags (aka tag_8021q operation). Even if commit
884be12f85 ("net: dsa: sja1105: add support for imprecise RX") added
this logic in sja1105_bridge_vlan_add():
/* Always install bridge VLANs as egress-tagged on the CPU port. */
if (dsa_is_cpu_port(ds, port))
flags = 0;
that was for _bridge_ VLANs, which are _not_ committed to hardware
in VLAN-unaware mode (aka the mode where ds->untag_bridge_pvid does
anything at all). Even prior to that change, the tag_8021q VLANs
were always installed as egress-tagged on the CPU port, see
dsa_switch_tag_8021q_vlan_add():
u16 flags = 0; // egress-tagged, non-PVID
if (dsa_port_is_user(dp))
flags |= BRIDGE_VLAN_INFO_UNTAGGED |
BRIDGE_VLAN_INFO_PVID;
err = dsa_port_do_tag_8021q_vlan_add(dp, info->vid,
flags);
if (err)
return err;
Whether the sja1105 driver needs the new flag, ds->untag_vlan_aware_bridge_pvid,
rather than ds->untag_bridge_pvid, is a separate discussion. To fix the
current bug in VLAN-unaware bridge mode, I would argue that the sja1105
driver should not request something it doesn't need, rather than
complicating the core DSA helper. Whereas before the blamed commit, this
setting was harmless, now it has caused breakage.
Fixes: 93e4649efa ("net: dsa: provide a software untagging function on RX for VLAN-aware bridges")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20241001140206.50933-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use xpcs_create_pcs_mdiodev() to create the XPCS instance, storing
and using the phylink_pcs pointer internally, rather than dw_xpcs.
Use xpcs_destroy_pcs() to destroy the XPCS instance when we've
finished with it.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1svfMk-005ZIj-R3@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Call the PCS operations through the ops structure, which avoids needing
to export xpcs internal functions.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1svfMf-005ZId-Mx@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The static configuration reload saves the port speed in the static
configuration tables by first converting it from the internal
respresentation to the SPEED_xxx ethtool representation, and then
converts it back to restore the setting. This is because
sja1105_adjust_port_config() takes the speed as SPEED_xxx.
However, this is unnecessarily complex. If we split
sja1105_adjust_port_config() up, we can simply save and restore the
mac[port].speed member in the static configuration tables.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1svfMa-005ZIX-If@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
Cross-merge networking fixes after downstream PR.
No conflicts (sort of) and no adjacent changes.
This merge reverts commit b3c9e65eb2 ("net: hsr: remove seqnr_lock")
from net, as it was superseded by
commit 430d67bdcb ("net: hsr: Use the seqnr lock for frames received via interlink port.")
in net-next.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The TAS module could not be configured when it's running in pending
status. We need disable the module and configure it again. However, the
pending status is not cleared after the module disabled. TC taprio set
will always return busy even it's disabled.
For example, a user uses tc-taprio to configure Qbv and a future
basetime. The TAS module will run in a pending status. There is no way
to reconfigure Qbv, it always returns busy.
Actually the TAS module can be reconfigured when it's disabled. So it
doesn't need to check the pending status if the TAS module is disabled.
After the patch, user can delete the tc taprio configuration to disable
Qbv and reconfigure it again.
Fixes: de143c0e27 ("net: dsa: felix: Configure Time-Aware Scheduler via taprio offload")
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Link: https://patch.msgid.link/20240906093550.29985-1-xiaoliang.yang_1@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace ksz8830 with ksz88x3 for CHIP_ID definition and other
strings. This due to KSZ8830 not being an actual switch but the Chip
ID shared among KSZ8863/8873 switches, impossible to differentiate
from their Chip ID or Revision ID registers.
Now all KSZ*_CHIP_ID macros refer to actual, existing switches which
removes confusion.
Signed-off-by: Pieter Van Trappen <pieter.van.trappen@cern.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove macros that are already defined at more appropriate places.
Signed-off-by: Pieter Van Trappen <pieter.van.trappen@cern.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first KSZ8 series implementation was done for a KSZ8795 device but
since several other KSZ8 devices have been added. Rename these files
to adhere to the ksz8 naming convention as already used in most
functions and the existing ksz8.h; add an explanatory note.
Signed-off-by: Pieter Van Trappen <pieter.van.trappen@cern.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the __counted_by compiler attribute to the flexible array member
entries to improve access bounds-checking via CONFIG_UBSAN_BOUNDS and
CONFIG_FORTIFY_SOURCE.
Signed-off-by: Hongbo Li <lihongbo22@huawei.com>
Link: https://patch.msgid.link/20240904014956.2035117-1-lihongbo22@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
