Since 4.10, commit 8003c9ae204e (KVM: LAPIC: add APIC Timer
periodic/oneshot mode VMX preemption timer support), guests using
periodic LAPIC timers (such as FreeBSD 8.4) would see their timers
drift significantly over time.
Differences in the underlying clocks and numerical errors means the
periods of the two timers (hv and sw) are not the same. This
difference will accumulate with every expiry resulting in a large
error between the hv and sw timer.
This means the sw timer may be running slow when compared to the hv
timer. When the timer is switched from hv to sw, the now active sw
timer will expire late. The guest VCPU is reentered and it switches to
using the hv timer. This timer catches up, injecting multiple IRQs
into the guest (of which the guest only sees one as it does not get to
run until the hv timer has caught up) and thus the guest's timer rate
is low (and becomes increasing slower over time as the sw timer lags
further and further behind).
I believe a similar problem would occur if the hv timer is the slower
one, but I have not observed this.
Fix this by synchronizing the deadlines for both timers to the same
time source on every tick. This prevents the errors from accumulating.
Fixes: 8003c9ae204e21204e49816c5ea629357e283b06
Cc: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: David Vrabel <david.vrabel@nutanix.com>
Cc: stable@vger.kernel.org
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Wanpeng Li <wanpengli@tencent.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
- Close a hole which could possibly lead to the host timebase getting
out of sync.
- Three fixes relating to PTEs and TLB entries for radix guests.
- Fix a bug which could lead to an interrupt never getting delivered
to the guest, if it is pending for a guest vCPU when the vCPU gets
offlined.
-----BEGIN PGP SIGNATURE-----
iQFGBAABCgAwFiEEv0VLfXa2m9eKuaRpnZrqdyxjcZ8FAlsGTWMSHHBhdWx1c0Bv
emxhYnMub3JnAAoJEJ2a6ncsY3GfPKQH/3dopz+qjpZqvhgvqfC0wkLlGLcTxmKK
+y77M5YStFEeytYB52hyrAs4KptM1If5+BfShX4tTzGY5MGS4RMvzY7tLNzLlmFg
S/ghzlFCh4dIz+LTk58FIyFmyn7GrvJRP33FoiAPCCp1AkRL7MlSD5cu3N6fHo6P
GU5lHLLyaGEIkC4KxLQdr4smV3tKNk1k6iz4eMHwDOeLoxcLnz0LbiM7xBr/Txmu
miF68B29hU/peKM/GbtSAh5TpWY6WlcPTBUEiHXghcuYmXqgW43fjGleuL330mN4
HtSONLuapa6VNSJy3UuGBlI1puIEbUrtTPfy0UxKQG3Em7L8UnxO2wk=
=7/7b
-----END PGP SIGNATURE-----
Merge tag 'kvm-ppc-fixes-4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
Fixes for PPC KVM:
- Close a hole which could possibly lead to the host timebase getting
out of sync.
- Three fixes relating to PTEs and TLB entries for radix guests.
- Fix a bug which could lead to an interrupt never getting delivered
to the guest, if it is pending for a guest vCPU when the vCPU gets
offlined.
KVM_HINTS_DEDICATED seems to be somewhat confusing:
Guest doesn't really care whether it's the only task running on a host
CPU as long as it's not preempted.
And there are more reasons for Guest to be preempted than host CPU
sharing, for example, with memory overcommit it can get preempted on a
memory access, post copy migration can cause preemption, etc.
Let's call it KVM_HINTS_REALTIME which seems to better
match what guests expect.
Also, the flag most be set on all vCPUs - current guests assume this.
Note so in the documentation.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
By missing an "L", we might detect some addresses to be <8k,
although they are not.
e.g. for itdba = 100001fff
!(gpa & ~0x1fffU) -> 1
!(gpa & ~0x1fffUL) -> 0
So we would report a SIE validity intercept although everything is fine.
Fixes: 166ecb3 ("KVM: s390: vsie: support transactional execution")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
A radix guest can execute tlbie instructions to invalidate TLB entries.
After a tlbie or a group of tlbies, it must then do the architected
sequence eieio; tlbsync; ptesync to ensure that the TLB invalidation
has been processed by all CPUs in the system before it can rely on
no CPU using any translation that it just invalidated.
In fact it is the ptesync which does the actual synchronization in
this sequence, and hardware has a requirement that the ptesync must
be executed on the same CPU thread as the tlbies which it is expected
to order. Thus, if a vCPU gets moved from one physical CPU to
another after it has done some tlbies but before it can get to do the
ptesync, the ptesync will not have the desired effect when it is
executed on the second physical CPU.
To fix this, we do a ptesync in the exit path for radix guests. If
there are any pending tlbies, this will wait for them to complete.
If there aren't, then ptesync will just do the same as sync.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
When a vcpu priority (CPPR) is set to a lower value (masking more
interrupts), we stop processing interrupts already in the queue
for the priorities that have now been masked.
If those interrupts were previously re-routed to a different
CPU, they might still be stuck until the older one that has
them in its queue processes them. In the case of guest CPU
unplug, that can be never.
To address that without creating additional overhead for
the normal interrupt processing path, this changes H_CPPR
handling so that when such a priority change occurs, we
scan the interrupt queue for that vCPU, and for any
interrupt in there that has been re-routed, we replace it
with a dummy and force a re-trigger.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The current partition table unmap code clears the _PAGE_PRESENT bit
out of the pte, which leaves pud_huge/pmd_huge true and does not
clear pud_present/pmd_present. This can confuse subsequent page
faults and possibly lead to the guest looping doing continual
hypervisor page faults.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The standard eieio ; tlbsync ; ptesync must follow tlbie to ensure it
is ordered with respect to subsequent operations.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Currently, the HV KVM guest entry/exit code adds the timebase offset
from the vcore struct to the timebase on guest entry, and subtracts
it on guest exit. Which is fine, except that it is possible for
userspace to change the offset using the SET_ONE_REG interface while
the vcore is running, as there is only one timebase offset per vcore
but potentially multiple VCPUs in the vcore. If that were to happen,
KVM would subtract a different offset on guest exit from that which
it had added on guest entry, leading to the timebase being out of sync
between cores in the host, which then leads to bad things happening
such as hangs and spurious watchdog timeouts.
To fix this, we add a new field 'tb_offset_applied' to the vcore struct
which stores the offset that is currently applied to the timebase.
This value is set from the vcore tb_offset field on guest entry, and
is what is subtracted from the timebase on guest exit. Since it is
zero when the timebase offset is not applied, we can simplify the
logic in kvmhv_start_timing and kvmhv_accumulate_time.
In addition, we had secondary threads reading the timebase while
running concurrently with code on the primary thread which would
eventually add or subtract the timebase offset from the timebase.
This occurred while saving or restoring the DEC register value on
the secondary threads. Although no specific incorrect behaviour has
been observed, this is a race which should be fixed. To fix it, we
move the DEC saving code to just before we call kvmhv_commence_exit,
and the DEC restoring code to after the point where we have waited
for the primary thread to switch the MMU context and add the timebase
offset. That way we are sure that the timebase contains the guest
timebase value in both cases.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
kvm_read_guest() will eventually look up in kvm_memslots(), which requires
either to hold the kvm->slots_lock or to be inside a kvm->srcu critical
section.
In contrast to x86 and s390 we don't take the SRCU lock on every guest
exit, so we have to do it individually for each kvm_read_guest() call.
Provide a wrapper which does that and use that everywhere.
Note that ending the SRCU critical section before returning from the
kvm_read_guest() wrapper is safe, because the data has been *copied*, so
we don't need to rely on valid references to the memslot anymore.
Cc: Stable <stable@vger.kernel.org> # 4.8+
Reported-by: Jan Glauber <jan.glauber@caviumnetworks.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Anthoine reported:
The period used by Windows change over time but it can be 1
milliseconds or less. I saw the limit_periodic_timer_frequency
print so 500 microseconds is sometimes reached.
As suggested by Paolo, lower the default timer frequency limit to a
smaller interval of 200 us (5000 Hz) to leave some headroom. This
is required due to Windows 10 changing the scheduler tick limit
from 1024 Hz to 2048 Hz.
Reported-by: Anthoine Bourgeois <anthoine.bourgeois@blade-group.com>
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Anthoine Bourgeois <anthoine.bourgeois@blade-group.com>
Cc: Darren Kenny <darren.kenny@oracle.com>
Cc: Jan Kiszka <jan.kiszka@web.de>
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Update SECONDARY_EXEC_DESC for UMIP emulation if and only UMIP
is actually being emulated. Skipping the VMCS update eliminates
unnecessary VMREAD/VMWRITE when UMIP is supported in hardware,
and on platforms that don't have SECONDARY_VM_EXEC_CONTROL. The
latter case resolves a bug where KVM would fill the kernel log
with warnings due to failed VMWRITEs on older platforms.
Fixes: 0367f205a3b7 ("KVM: vmx: add support for emulating UMIP")
Cc: stable@vger.kernel.org #4.16
Reported-by: Paolo Zeppegno <pzeppegno@gmail.com>
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Suggested-by: Radim KrÄmář <rkrcmar@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If the PCIDE bit is not set in CR4, then the MSb of CR3 is a reserved
bit. If the guest tries to set it, that should cause a #GP fault. So
mask out the bit only when the PCIDE bit is set.
Signed-off-by: Junaid Shahid <junaids@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Even though the eventfd is released after the KVM SRCU grace period
elapses, the conn_to_evt data structure itself is not; it uses RCU
internally, instead. Fix the read-side critical section to happen
under rcu_read_lock/unlock; the result is still protected by
vcpu->kvm->srcu.
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The IP increment should be done after the hypercall emulation, after
calling the various handlers. In this way, these handlers can accurately
identify the the IP of the VMCALL if they need it.
This patch keeps the same functionality for the Hyper-V handler which does
not use the return code of the standard kvm_skip_emulated_instruction()
call.
Signed-off-by: Marian Rotariu <mrotariu@bitdefender.com>
[Hyper-V hypercalls also need kvm_skip_emulated_instruction() - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
ARM:
- Fix proxying of GICv2 CPU interface accesses
- Fix crash when switching to BE
- Track source vcpu git GICv2 SGIs
- Fix an outdated bit of documentation
x86:
- Speed up injection of expired timers (for stable)
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJa7s3kAAoJEED/6hsPKofojlwIAKQLt6GuAHTj7Gl+G4/EOOSk
bXSXracJSi3aQHTVdKaREo6iTpAB7/E/4yf+KLkljiqPO/YrWrlTnAbqfCfjqX6b
pWyXgoxPy4v+SEbhP+qiV/yC/HiuPJ4WZVmf5cCDXD4kPF03b7DvImGbZRbEwJNV
qlaO1QqmbbMU5m1I5oZCKn5/BLM3fwAFMn1RERFDOPyn3+HPwANRbnLsZ4q49KHw
W41Rj6i88qDQ3PrbgUCmSvuzboKwTiVUBltPlStk9A04F2toLytcMoo9fdzQOjwD
ZmvjYlLqNlxXFLUHHvhgOECvBTp879AWUrgoManQ16O1s/gApTcHdXpzKQBKjtE=
=I6Dd
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pll KVM fixes from Radim Krčmář:
"ARM:
- Fix proxying of GICv2 CPU interface accesses
- Fix crash when switching to BE
- Track source vcpu git GICv2 SGIs
- Fix an outdated bit of documentation
x86:
- Speed up injection of expired timers (for stable)"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: remove APIC Timer periodic/oneshot spikes
arm64: vgic-v2: Fix proxying of cpuif access
KVM: arm/arm64: vgic_init: Cleanup reference to process_maintenance
KVM: arm64: Fix order of vcpu_write_sys_reg() arguments
KVM: arm/arm64: vgic: Fix source vcpu issues for GICv2 SGI
Pull x86 fix from Thomas Gleixner:
"Unbreak the CPUID CPUID_8000_0008_EBX reload which got dropped when
the evaluation of physical and virtual bits which uses the same CPUID
leaf was moved out of get_cpu_cap()"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu: Restore CPUID_8000_0008_EBX reload
Pull clocksource fixes from Thomas Gleixner:
"The recent addition of the early TSC clocksource breaks on machines
which have an unstable TSC because in case that TSC is disabled, then
the clocksource selection logic falls back to the early TSC which is
obviously bogus.
That also unearthed a few robustness issues in the clocksource
derating code which are addressed as well"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: Rework stale comment
clocksource: Consistent de-rate when marking unstable
x86/tsc: Fix mark_tsc_unstable()
clocksource: Initialize cs->wd_list
clocksource: Allow clocksource_mark_unstable() on unregistered clocksources
x86/tsc: Always unregister clocksource_tsc_early
Since the commit "8003c9ae204e: add APIC Timer periodic/oneshot mode VMX
preemption timer support", a Windows 10 guest has some erratic timer
spikes.
Here the results on a 150000 times 1ms timer without any load:
Before 8003c9ae204e | After 8003c9ae204e
Max 1834us | 86000us
Mean 1100us | 1021us
Deviation 59us | 149us
Here the results on a 150000 times 1ms timer with a cpu-z stress test:
Before 8003c9ae204e | After 8003c9ae204e
Max 32000us | 140000us
Mean 1006us | 1997us
Deviation 140us | 11095us
The root cause of the problem is starting hrtimer with an expiry time
already in the past can take more than 20 milliseconds to trigger the
timer function. It can be solved by forward such past timers
immediately, rather than submitting them to hrtimer_start().
In case the timer is periodic, update the target expiration and call
hrtimer_start with it.
v2: Check if the tsc deadline is already expired. Thank you Mika.
v3: Execute the past timers immediately rather than submitting them to
hrtimer_start().
v4: Rearm the periodic timer with advance_periodic_target_expiration() a
simpler version of set_target_expiration(). Thank you Paolo.
Cc: Mika Penttilä <mika.penttila@nextfour.com>
Cc: Wanpeng Li <kernellwp@gmail.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Anthoine Bourgeois <anthoine.bourgeois@blade-group.com>
8003c9ae204e ("KVM: LAPIC: add APIC Timer periodic/oneshot mode VMX preemption timer support")
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
- Fix proxying of GICv2 CPU interface accesses
- Fix crash when switching to BE
- Track source vcpu git GICv2 SGIs
- Fix an outdated bit of documentation
-----BEGIN PGP SIGNATURE-----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=cO6X
-----END PGP SIGNATURE-----
Merge tag 'kvmarm-fixes-for-4.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm
KVM/arm fixes for 4.17, take #2
- Fix proxying of GICv2 CPU interface accesses
- Fix crash when switching to BE
- Track source vcpu git GICv2 SGIs
- Fix an outdated bit of documentation
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCWuwoogAKCRCAXGG7T9hj
vr23AP4vj3yoii3mihZYjDahwyE+3fILUWECl/d/cMXGxq5tbgD9Esvb6DgtKHJr
Hi/lPMVM0XmN/DIXhY9x7SqO2cKvEAU=
=XwLB
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.17-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen cleanup from Juergen Gross:
"One cleanup to remove VLAs from the kernel"
* tag 'for-linus-4.17-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
x86/xen: Remove use of VLAs
Proxying the cpuif accesses at EL2 makes use of vcpu_data_guest_to_host
and co, which check the endianness, which call into vcpu_read_sys_reg...
which isn't mapped at EL2 (it was inlined before, and got moved OoL
with the VHE optimizations).
The result is of course a nice panic. Let's add some specialized
cruft to keep the broken platforms that require this hack alive.
But, this code used vcpu_data_guest_to_host(), which expected us to
write the value to host memory, instead we have trapped the guest's
read or write to an mmio-device, and are about to replay it using the
host's readl()/writel() which also perform swabbing based on the host
endianness. This goes wrong when both host and guest are big-endian,
as readl()/writel() will undo the guest's swabbing, causing the
big-endian value to be written to device-memory.
What needs doing?
A big-endian guest will have pre-swabbed data before storing, undo this.
If its necessary for the host, writel() will re-swab it.
For a read a big-endian guest expects to swab the data after the load.
The hosts's readl() will correct for host endianness, giving us the
device-memory's value in the register. For a big-endian guest, swab it
as if we'd only done the load.
For a little-endian guest, nothing needs doing as readl()/writel() leave
the correct device-memory value in registers.
Tested on Juno with that rarest of things: a big-endian 64K host.
Based on a patch from Marc Zyngier.
Reported-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Fixes: bf8feb39642b ("arm64: KVM: vgic-v2: Add GICV access from HYP")
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
A typo in kvm_vcpu_set_be()'s call:
| vcpu_write_sys_reg(vcpu, SCTLR_EL1, sctlr)
causes us to use the 32bit register value as an index into the sys_reg[]
array, and sail off the end of the linear map when we try to bring up
big-endian secondaries.
| Unable to handle kernel paging request at virtual address ffff80098b982c00
| Mem abort info:
| ESR = 0x96000045
| Exception class = DABT (current EL), IL = 32 bits
| SET = 0, FnV = 0
| EA = 0, S1PTW = 0
| Data abort info:
| ISV = 0, ISS = 0x00000045
| CM = 0, WnR = 1
| swapper pgtable: 4k pages, 48-bit VAs, pgdp = 000000002ea0571a
| [ffff80098b982c00] pgd=00000009ffff8803, pud=0000000000000000
| Internal error: Oops: 96000045 [#1] PREEMPT SMP
| Modules linked in:
| CPU: 2 PID: 1561 Comm: kvm-vcpu-0 Not tainted 4.17.0-rc3-00001-ga912e2261ca6-dirty #1323
| Hardware name: ARM Juno development board (r1) (DT)
| pstate: 60000005 (nZCv daif -PAN -UAO)
| pc : vcpu_write_sys_reg+0x50/0x134
| lr : vcpu_write_sys_reg+0x50/0x134
| Process kvm-vcpu-0 (pid: 1561, stack limit = 0x000000006df4728b)
| Call trace:
| vcpu_write_sys_reg+0x50/0x134
| kvm_psci_vcpu_on+0x14c/0x150
| kvm_psci_0_2_call+0x244/0x2a4
| kvm_hvc_call_handler+0x1cc/0x258
| handle_hvc+0x20/0x3c
| handle_exit+0x130/0x1ec
| kvm_arch_vcpu_ioctl_run+0x340/0x614
| kvm_vcpu_ioctl+0x4d0/0x840
| do_vfs_ioctl+0xc8/0x8d0
| ksys_ioctl+0x78/0xa8
| sys_ioctl+0xc/0x18
| el0_svc_naked+0x30/0x34
| Code: 73620291 604d00b0 00201891 1ab10194 (957a33f8)
|---[ end trace 4b4a4f9628596602 ]---
Fix the order of the arguments.
Fixes: 8d404c4c24613 ("KVM: arm64: Rewrite system register accessors to read/write functions")
CC: Christoffer Dall <cdall@cs.columbia.edu>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Pull networking fixes from David Miller:
1) Various sockmap fixes from John Fastabend (pinned map handling,
blocking in recvmsg, double page put, error handling during redirect
failures, etc.)
2) Fix dead code handling in x86-64 JIT, from Gianluca Borello.
3) Missing device put in RDS IB code, from Dag Moxnes.
4) Don't process fast open during repair mode in TCP< from Yuchung
Cheng.
5) Move address/port comparison fixes in SCTP, from Xin Long.
6) Handle add a bond slave's master into a bridge properly, from
Hangbin Liu.
7) IPv6 multipath code can operate on unitialized memory due to an
assumption that the icmp header is in the linear SKB area. Fix from
Eric Dumazet.
8) Don't invoke do_tcp_sendpages() recursively via TLS, from Dave
Watson.
9) Fix memory leaks in x86-64 JIT, from Daniel Borkmann.
10) RDS leaks kernel memory to userspace, from Eric Dumazet.
11) DCCP can invoke a tasklet on a freed socket, take a refcount. Also
from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (78 commits)
dccp: fix tasklet usage
smc: fix sendpage() call
net/smc: handle unregistered buffers
net/smc: call consolidation
qed: fix spelling mistake: "offloded" -> "offloaded"
net/mlx5e: fix spelling mistake: "loobpack" -> "loopback"
tcp: restore autocorking
rds: do not leak kernel memory to user land
qmi_wwan: do not steal interfaces from class drivers
ipv4: fix fnhe usage by non-cached routes
bpf: sockmap, fix error handling in redirect failures
bpf: sockmap, zero sg_size on error when buffer is released
bpf: sockmap, fix scatterlist update on error path in send with apply
net_sched: fq: take care of throttled flows before reuse
ipv6: Revert "ipv6: Allow non-gateway ECMP for IPv6"
bpf, x64: fix memleak when not converging on calls
bpf, x64: fix memleak when not converging after image
net/smc: restrict non-blocking connect finish
8139too: Use disable_irq_nosync() in rtl8139_poll_controller()
sctp: fix the issue that the cookie-ack with auth can't get processed
...
Fix three section mismatches:
1) Section mismatch in reference from the function ioread8() to the
function .init.text:pcibios_init_bridge()
2) Section mismatch in reference from the function free_initmem() to the
function .init.text:map_pages()
3) Section mismatch in reference from the function ccio_ioc_init() to
the function .init.text:count_parisc_driver()
Signed-off-by: Helge Deller <deller@gmx.de>
Fix two section mismatches in drivers.c:
1) Section mismatch in reference from the function alloc_tree_node() to
the function .init.text:create_tree_node().
2) Section mismatch in reference from the function walk_native_bus() to
the function .init.text:alloc_pa_dev().
Signed-off-by: Helge Deller <deller@gmx.de>
The JIT logic in jit_subprogs() is as follows: for all subprogs we
allocate a bpf_prog_alloc(), populate it (prog->is_func = 1 here),
and pass it to bpf_int_jit_compile(). If a failure occurred during
JIT and prog->jited is not set, then we bail out from attempting to
JIT the whole program, and punt to the interpreter instead. In case
JITing went successful, we fixup BPF call offsets and do another
pass to bpf_int_jit_compile() (extra_pass is true at that point) to
complete JITing calls. Given that requires to pass JIT context around
addrs and jit_data from x86 JIT are freed in the extra_pass in
bpf_int_jit_compile() when calls are involved (if not, they can
be freed immediately). However, if in the original pass, the JIT
image didn't converge then we leak addrs and jit_data since image
itself is NULL, the prog->is_func is set and extra_pass is false
in that case, meaning both will become unreachable and are never
cleaned up, therefore we need to free as well on !image. Only x64
JIT is affected.
Fixes: 1c2a088a6626 ("bpf: x64: add JIT support for multi-function programs")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
While reviewing x64 JIT code, I noticed that we leak the prior allocated
JIT image in the case where proglen != oldproglen during the JIT passes.
Prior to the commit e0ee9c12157d ("x86: bpf_jit: fix two bugs in eBPF JIT
compiler") we would just break out of the loop, and using the image as the
JITed prog since it could only shrink in size anyway. After e0ee9c12157d,
we would bail out to out_addrs label where we free addrs and jit_data but
not the image coming from bpf_jit_binary_alloc().
Fixes: e0ee9c12157d ("x86: bpf_jit: fix two bugs in eBPF JIT compiler")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The recent commt which addresses the x86_phys_bits corruption with
encrypted memory on CPUID reload after a microcode update lost the reload
of CPUID_8000_0008_EBX as well.
As a consequence IBRS and IBRS_FW are not longer detected
Restore the behaviour by bringing the reload of CPUID_8000_0008_EBX
back. This restore has a twist due to the convoluted way the cpuid analysis
works:
CPUID_8000_0008_EBX is used by AMD to enumerate IBRB, IBRS, STIBP. On Intel
EBX is not used. But the speculation control code sets the AMD bits when
running on Intel depending on the Intel specific speculation control
bits. This was done to use the same bits for alternatives.
The change which moved the 8000_0008 evaluation out of get_cpu_cap() broke
this nasty scheme due to ordering. So that on Intel the store to
CPUID_8000_0008_EBX clears the IBRB, IBRS, STIBP bits which had been set
before by software.
So the actual CPUID_8000_0008_EBX needs to go back to the place where it
was and the phys/virt address space calculation cannot touch it.
In hindsight this should have used completely synthetic bits for IBRB,
IBRS, STIBP instead of reusing the AMD bits, but that's for 4.18.
/me needs to find time to cleanup that steaming pile of ...
Fixes: d94a155c59c9 ("x86/cpu: Prevent cpuinfo_x86::x86_phys_bits adjustment corruption")
Reported-by: Jörg Otte <jrg.otte@gmail.com>
Reported-by: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Jörg Otte <jrg.otte@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: kirill.shutemov@linux.intel.com
Cc: Borislav Petkov <bp@alien8.de
Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1805021043510.1668@nanos.tec.linutronix.de
mark_tsc_unstable() also needs to affect tsc_early, Now that
clocksource_mark_unstable() can be used on a clocksource irrespective of
its registration state, use it on both tsc_early and tsc.
This does however require cs->list to be initialized empty, otherwise it
cannot tell the registation state before registation.
Fixes: aa83c45762a2 ("x86/tsc: Introduce early tsc clocksource")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Diego Viola <diego.viola@gmail.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: len.brown@intel.com
Cc: rjw@rjwysocki.net
Cc: rui.zhang@intel.com
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20180430100344.533326547@infradead.org
Don't leave the tsc-early clocksource registered if it errors out
early.
This was reported by Diego, who on his Core2 era machine got TSC
invalidated while it was running with tsc-early (due to C-states).
This results in keeping tsc-early with very bad effects.
Reported-and-Tested-by: Diego Viola <diego.viola@gmail.com>
Fixes: aa83c45762a2 ("x86/tsc: Introduce early tsc clocksource")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: len.brown@intel.com
Cc: rjw@rjwysocki.net
Cc: diego.viola@gmail.com
Cc: rui.zhang@intel.com
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20180430100344.350507853@infradead.org
Pull hexagon fixes from Richard Kuo:
"Some small fixes for module compilation"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rkuo/linux-hexagon-kernel:
hexagon: export csum_partial_copy_nocheck
hexagon: add memset_io() helper
This is needed to link ipv6 as a loadable module, which in turn happens
in allmodconfig.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
We already have memcpy_toio(), but not memset_io(), so let's
add the obvious version to allow building an allmodconfig kernel
without errors like
drivers/gpu/drm/ttm/ttm_bo_util.c: In function 'ttm_bo_move_memcpy':
drivers/gpu/drm/ttm/ttm_bo_util.c:390:3: error: implicit declaration of function 'memset_io' [-Werror=implicit-function-declaration]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
- Fixup license text for oradax driver, from Rob Gardner.
- Release device object with put_device() instead of straight kfree(),
from Arvind Yadav.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: vio: use put_device() instead of kfree()
sparc64: Fix mistake in oradax license text
Never directly free @dev after calling device_register(), even
if it returned an error. Always use put_device() to give up the
reference initialized.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The license text in both oradax files mistakenly specifies "version 3" of
the GNU General Public License. This is corrected to specify "version 2".
Signed-off-by: Rob Gardner <rob.gardner@oracle.com>
Signed-off-by: Jonathan Helman <jonathan.helman@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull x86 fixes from Thomas Gleixner:
"Another set of x86 related updates:
- Fix the long broken x32 version of the IPC user space headers which
was noticed by Arnd Bergman in course of his ongoing y2038 work.
GLIBC seems to have non broken private copies of these headers so
this went unnoticed.
- Two microcode fixlets which address some more fallout from the
recent modifications in that area:
- Unconditionally save the microcode patch, which was only saved
when CPU_HOTPLUG was enabled causing failures in the late
loading mechanism
- Make the later loader synchronization finally work under all
circumstances. It was exiting early and causing timeout failures
due to a missing synchronization point.
- Do not use mwait_play_dead() on AMD systems to prevent excessive
power consumption as the CPU cannot go into deep power states from
there.
- Address an annoying sparse warning due to lost type qualifiers of
the vmemmap and vmalloc base address constants.
- Prevent reserving crash kernel region on Xen PV as this leads to
the wrong perception that crash kernels actually work there which
is not the case. Xen PV has its own crash mechanism handled by the
hypervisor.
- Add missing TLB cpuid values to the table to make the printout on
certain machines correct.
- Enumerate the new CLDEMOTE instruction
- Fix an incorrect SPDX identifier
- Remove stale macros"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/ipc: Fix x32 version of shmid64_ds and msqid64_ds
x86/setup: Do not reserve a crash kernel region if booted on Xen PV
x86/cpu/intel: Add missing TLB cpuid values
x86/smpboot: Don't use mwait_play_dead() on AMD systems
x86/mm: Make vmemmap and vmalloc base address constants unsigned long
x86/vector: Remove the unused macro FPU_IRQ
x86/vector: Remove the macro VECTOR_OFFSET_START
x86/cpufeatures: Enumerate cldemote instruction
x86/microcode: Do not exit early from __reload_late()
x86/microcode/intel: Save microcode patch unconditionally
x86/jailhouse: Fix incorrect SPDX identifier
Pull x86 pti fixes from Thomas Gleixner:
"A set of updates for the x86/pti related code:
- Preserve r8-r11 in int $0x80. r8-r11 need to be preserved, but the
int$80 entry code removed that quite some time ago. Make it correct
again.
- A set of fixes for the Global Bit work which went into 4.17 and
caused a bunch of interesting regressions:
- Triggering a BUG in the page attribute code due to a missing
check for early boot stage
- Warnings in the page attribute code about holes in the kernel
text mapping which are caused by the freeing of the init code.
Handle such holes gracefully.
- Reduce the amount of kernel memory which is set global to the
actual text and do not incidentally overlap with data.
- Disable the global bit when RANDSTRUCT is enabled as it
partially defeats the hardening.
- Make the page protection setup correct for vma->page_prot
population again. The adjustment of the protections fell through
the crack during the Global bit rework and triggers warnings on
machines which do not support certain features, e.g. NX"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/entry/64/compat: Preserve r8-r11 in int $0x80
x86/pti: Filter at vma->vm_page_prot population
x86/pti: Disallow global kernel text with RANDSTRUCT
x86/pti: Reduce amount of kernel text allowed to be Global
x86/pti: Fix boot warning from Global-bit setting
x86/pti: Fix boot problems from Global-bit setting
Pull perf fixes from Thomas Gleixner:
"The perf update contains the following bits:
x86:
- Prevent setting freeze_on_smi on PerfMon V1 CPUs to avoid #GP
perf stat:
- Keep the '/' event modifier separator in fallback, for example when
fallbacking from 'cpu/cpu-cycles/' to user level only, where it
should become 'cpu/cpu-cycles/u' and not 'cpu/cpu-cycles/:u' (Jiri
Olsa)
- Fix PMU events parsing rule, improving error reporting for invalid
events (Jiri Olsa)
- Disable write_backward and other event attributes for !group events
in a group, fixing, for instance this group: '{cycles,msr/aperf/}:S'
that has leader sampling (:S) and where just the 'cycles', the
leader event, should have the write_backward attribute set, in this
case it all fails because the PMU where 'msr/aperf/' lives doesn't
accepts write_backward style sampling (Jiri Olsa)
- Only fall back group read for leader (Kan Liang)
- Fix core PMU alias list for x86 platform (Kan Liang)
- Print out hint for mixed PMU group error (Kan Liang)
- Fix duplicate PMU name for interval print (Kan Liang)
Core:
- Set main kernel end address properly when reading kernel and module
maps (Namhyung Kim)
perf mem:
- Fix incorrect entries and add missing man options (Sangwon Hong)
s/390:
- Remove s390 specific strcmp_cpuid_cmp function (Thomas Richter)
- Adapt 'perf test' case record+probe_libc_inet_pton.sh for s390
- Fix s390 undefined record__auxtrace_init() return value in 'perf
record' (Thomas Richter)"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel: Don't enable freeze-on-smi for PerfMon V1
perf stat: Fix duplicate PMU name for interval print
perf evsel: Only fall back group read for leader
perf stat: Print out hint for mixed PMU group error
perf pmu: Fix core PMU alias list for X86 platform
perf record: Fix s390 undefined record__auxtrace_init() return value
perf mem: Document incorrect and missing options
perf evsel: Disable write_backward for leader sampling group events
perf pmu: Fix pmu events parsing rule
perf stat: Keep the / modifier separator in fallback
perf test: Adapt test case record+probe_libc_inet_pton.sh for s390
perf list: Remove s390 specific strcmp_cpuid_cmp function
perf machine: Set main kernel end address properly
A bunch of fixes, mostly for existing code and going to stable.
Our memory hot-unplug path wasn't flushing the cache before removing memory.
That is a problem now that we are doing memory hotplug on bare metal.
Three fixes for the NPU code that supports devices connected via NVLink (ie.
GPUs). The main one tweaks the TLB flush algorithm to avoid soft lockups for
large flushes.
A fix for our memory error handling where we would loop infinitely, returning
back to the bad access and hard lockup the CPU.
Fixes for the OPAL RTC driver, which wasn't handling some error cases correctly.
A fix for a hardlockup in the powernv cpufreq driver.
And finally two fixes to our smp_send_stop(), required due to a recent change to
use it on shutdown.
Thanks to:
Alistair Popple, Balbir Singh, Laurentiu Tudor, Mahesh Salgaonkar, Mark
Hairgrove, Nicholas Piggin, Rashmica Gupta, Shilpasri G Bhat.
-----BEGIN PGP SIGNATURE-----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=JJLB
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.17-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"A bunch of fixes, mostly for existing code and going to stable.
Our memory hot-unplug path wasn't flushing the cache before removing
memory. That is a problem now that we are doing memory hotplug on bare
metal.
Three fixes for the NPU code that supports devices connected via
NVLink (ie. GPUs). The main one tweaks the TLB flush algorithm to
avoid soft lockups for large flushes.
A fix for our memory error handling where we would loop infinitely,
returning back to the bad access and hard lockup the CPU.
Fixes for the OPAL RTC driver, which wasn't handling some error cases
correctly.
A fix for a hardlockup in the powernv cpufreq driver.
And finally two fixes to our smp_send_stop(), required due to a recent
change to use it on shutdown.
Thanks to: Alistair Popple, Balbir Singh, Laurentiu Tudor, Mahesh
Salgaonkar, Mark Hairgrove, Nicholas Piggin, Rashmica Gupta, Shilpasri
G Bhat"
* tag 'powerpc-4.17-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/kvm/booke: Fix altivec related build break
powerpc: Fix deadlock with multiple calls to smp_send_stop
cpufreq: powernv: Fix hardlockup due to synchronous smp_call in timer interrupt
powerpc: Fix smp_send_stop NMI IPI handling
rtc: opal: Fix OPAL RTC driver OPAL_BUSY loops
powerpc/mce: Fix a bug where mce loops on memory UE.
powerpc/powernv/npu: Do a PID GPU TLB flush when invalidating a large address range
powerpc/powernv/npu: Prevent overwriting of pnv_npu2_init_contex() callback parameters
powerpc/powernv/npu: Add lock to prevent race in concurrent context init/destroy
powerpc/powernv/memtrace: Let the arch hotunplug code flush cache
powerpc/mm: Flush cache on memory hot(un)plug
ARM:
- PSCI selection API, a leftover from 4.16 (for stable)
- Kick vcpu on active interrupt affinity change
- Plug a VMID allocation race on oversubscribed systems
- Silence debug messages
- Update Christoffer's email address (linaro -> arm)
x86:
- Expose userspace-relevant bits of a newly added feature
- Fix TLB flushing on VMX with VPID, but without EPT
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJa44lQAAoJEED/6hsPKofo1dIH/3n9AZSWvavgL2V3j6agT8Yy
hxF4nHCFEJd5aqDNwbG9QEzivKw88r3o3mdB2XAQESB2MlCYR1jkTONm7yvVJTs/
/P9gj+DEQbCj2AgT//u3BGsAsZDKFhB9JwfmV2Mp4zDIqWFa6oCOGeq/iPVAGDcN
vUpuYeIicuH9SRoxH7de3z+BEXW0O+gCABXQtvA93FKTMz35yFTgmbDVCnvaV0zL
3B+3/4/jdbTRICW8EX6Li43+gEBUMtnVNkdqxLPTuCtDG8iuPUGfgF02gH99/9gj
hliV3Q4VUZKkSABW5AqKPe4+9rbsHCh9eL0LpHFGI9y+6LeUIOXAX4CtohR8gWE=
=W9Vz
-----END PGP SIGNATURE-----
rMerge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Radim Krčmář:
"ARM:
- PSCI selection API, a leftover from 4.16 (for stable)
- Kick vcpu on active interrupt affinity change
- Plug a VMID allocation race on oversubscribed systems
- Silence debug messages
- Update Christoffer's email address (linaro -> arm)
x86:
- Expose userspace-relevant bits of a newly added feature
- Fix TLB flushing on VMX with VPID, but without EPT"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
x86/headers/UAPI: Move DISABLE_EXITS KVM capability bits to the UAPI
kvm: apic: Flush TLB after APIC mode/address change if VPIDs are in use
arm/arm64: KVM: Add PSCI version selection API
KVM: arm/arm64: vgic: Kick new VCPU on interrupt migration
arm64: KVM: Demote SVE and LORegion warnings to debug only
MAINTAINERS: Update e-mail address for Christoffer Dall
KVM: arm/arm64: Close VMID generation race
- Close some potential spectre-v1 vulnerabilities found by smatch
- Add missing list sentinel for CPUs that don't require KPTI
- Removal of unused 'addr' parameter for I/D cache coherency
- Removal of redundant set_fs(KERNEL_DS) calls in ptrace
- Fix single-stepping state machine handling in response to kernel traps
- Clang support for 128-bit integers
- Avoid instrumenting our out-of-line atomics in preparation for enabling
LSE atomics by default in 4.18
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJa4w6JAAoJELescNyEwWM0P2IIAMLITiYvB+LEwWH6VZ5zl+D0
F1qoQPon6M68fSc86rNNwoOrLzisHPTMMyR3re5+rHe67EwHCMtupkNk3s/+/vi3
PVq3W2Rjw9GTFL/7sDNmaHvJLQ3lG1HAh4uO2WneLbLV6wkbw7/JlmCcwlS48zB0
zxY5fKnZNPCAfAT34TYZGMHINy5rOoo7+H3+/ZB/f4jc3FIatfnsUb3+Mr5B/lZ9
HoOddh9PEt+CY2v5Yr2M6FJuu/oaZdX+KaAUlynd44jyF+XgB5BxXTEHoD4bEO9l
q8CzjqzUqqBn8qSF36r/gdffH4eAKkrFgMCxjdEbPX1cOj67fTquNALBmAhAA7M=
=CIk+
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Nothing too bad, but the spectre updates to smatch identified a few
places that may need sanitising so we've got those covered.
Details:
- Close some potential spectre-v1 vulnerabilities found by smatch
- Add missing list sentinel for CPUs that don't require KPTI
- Removal of unused 'addr' parameter for I/D cache coherency
- Removal of redundant set_fs(KERNEL_DS) calls in ptrace
- Fix single-stepping state machine handling in response to kernel
traps
- Clang support for 128-bit integers
- Avoid instrumenting our out-of-line atomics in preparation for
enabling LSE atomics by default in 4.18"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: avoid instrumenting atomic_ll_sc.o
KVM: arm/arm64: vgic: fix possible spectre-v1 in vgic_mmio_read_apr()
KVM: arm/arm64: vgic: fix possible spectre-v1 in vgic_get_irq()
arm64: fix possible spectre-v1 in ptrace_hbp_get_event()
arm64: support __int128 with clang
arm64: only advance singlestep for user instruction traps
arm64/kernel: rename module_emit_adrp_veneer->module_emit_veneer_for_adrp
arm64: ptrace: remove addr_limit manipulation
arm64: mm: drop addr parameter from sync icache and dcache
arm64: add sentinel to kpti_safe_list
Move DISABLE_EXITS KVM capability bits to the UAPI just like the rest of
capabilities.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: x86@kernel.org
Cc: kvm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: KarimAllah Ahmed <karahmed@amazon.de>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
This round of fixes has two larger changes that came in last week:
- A set of a couple of patches all intended to finally turn on
USB support on various Amlogic SoC based boards. The respective
driver were not finalized until very late before the merge window
and the DT portion is the last bit now.
- A defconfig update for gemini that had repeatedly missed the
cut but that is required to actually boot any real machines
with the default build.
The rest are the usual small changes:
- A fix for a nasty build regression on the OMAP memory drivers
- A fix for a boot problem on Intel/Altera SocFPGA
- A MAINTAINER file update
- A couple of fixes for issues found by automated testing
(kernelci, coverity, sparse, ...)
- A few incorrect DT entries are updated to match the hardware
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Zhll
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"This round of fixes has two larger changes that came in last week:
- a couple of patches all intended to finally turn on USB support on
various Amlogic SoC based boards. The respective driver were not
finalized until very late before the merge window and the DT
portion is the last bit now.
- a defconfig update for gemini that had repeatedly missed the cut
but that is required to actually boot any real machines with the
default build.
The rest are the usual small changes:
- a fix for a nasty build regression on the OMAP memory drivers
- a fix for a boot problem on Intel/Altera SocFPGA
- a MAINTAINER file update
- a couple of fixes for issues found by automated testing (kernelci,
coverity, sparse, ...)
- a few incorrect DT entries are updated to match the hardware"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: defconfig: Update Gemini defconfig
ARM: s3c24xx: jive: Fix some GPIO names
HISI LPC: Add Kconfig MFD_CORE dependency
ARM: dts: Fix NAS4220B pin config
MAINTAINERS: Remove myself as maintainer
arm64: dts: correct SATA addresses for Stingray
ARM64: dts: meson-gxm-khadas-vim2: enable the USB controller
ARM64: dts: meson-gxl-nexbox-a95x: enable the USB controller
ARM64: dts: meson-gxl-s905x-libretech-cc: enable the USB controller
ARM64: dts: meson-gx-p23x-q20x: enable the USB controller
ARM64: dts: meson-gxl-s905x-p212: enable the USB controller
ARM64: dts: meson-gxm: add GXM specific USB host configuration
ARM64: dts: meson-gxl: add USB host support
ARM: OMAP2+: Fix build when using split object directories
soc: bcm2835: Make !RASPBERRYPI_FIRMWARE dummies return failure
soc: bcm: raspberrypi-power: Fix use of __packed
ARM: dts: Fix cm2 and prm sizes for omap4
ARM: socfpga_defconfig: Remove QSPI Sector 4K size force
firmware: arm_scmi: remove redundant null check on array
arm64: dts: juno: drop unnecessary address-cells and size-cells properties
Currently, KVM flushes the TLB after a change to the APIC access page
address or the APIC mode when EPT mode is enabled. However, even in
shadow paging mode, a TLB flush is needed if VPIDs are being used, as
specified in the Intel SDM Section 29.4.5.
So replace vmx_flush_tlb_ept_only() with vmx_flush_tlb(), which will
flush if either EPT or VPIDs are in use.
Signed-off-by: Junaid Shahid <junaids@google.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
32-bit user code that uses int $80 doesn't care about r8-r11. There is,
however, some 64-bit user code that intentionally uses int $0x80 to invoke
32-bit system calls. From what I've seen, basically all such code assumes
that r8-r15 are all preserved, but the kernel clobbers r8-r11. Since I
doubt that there's any code that depends on int $0x80 zeroing r8-r11,
change the kernel to preserve them.
I suspect that very little user code is broken by the old clobber, since
r8-r11 are only rarely allocated by gcc, and they're clobbered by function
calls, so they only way we'd see a problem is if the same function that
invokes int $0x80 also spills something important to one of these
registers.
The current behavior seems to date back to the historical commit
"[PATCH] x86-64 merge for 2.6.4". Before that, all regs were
preserved. I can't find any explanation of why this change was made.
Update the test_syscall_vdso_32 testcase as well to verify the new
behavior, and it strengthens the test to make sure that the kernel doesn't
accidentally permute r8..r15.
Suggested-by: Denys Vlasenko <dvlasenk@redhat.com>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Link: https://lkml.kernel.org/r/d4c4d9985fbe64f8c9e19291886453914b48caee.1523975710.git.luto@kernel.org
A bugfix broke the x32 shmid64_ds and msqid64_ds data structure layout
(as seen from user space) a few years ago: Originally, __BITS_PER_LONG
was defined as 64 on x32, so we did not have padding after the 64-bit
__kernel_time_t fields, After __BITS_PER_LONG got changed to 32,
applications would observe extra padding.
In other parts of the uapi headers we seem to have a mix of those
expecting either 32 or 64 on x32 applications, so we can't easily revert
the path that broke these two structures.
Instead, this patch decouples x32 from the other architectures and moves
it back into arch specific headers, partially reverting the even older
commit 73a2d096fdf2 ("x86: remove all now-duplicate header files").
It's not clear whether this ever made any difference, since at least
glibc carries its own (correct) copy of both of these header files,
so possibly no application has ever observed the definitions here.
Based on a suggestion from H.J. Lu, I tried out the tool from
https://github.com/hjl-tools/linux-header to find other such
bugs, which pointed out the same bug in statfs(), which also has
a separate (correct) copy in glibc.
Fixes: f4b4aae18288 ("x86/headers/uapi: Fix __BITS_PER_LONG value for x32 builds")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "H . J . Lu" <hjl.tools@gmail.com>
Cc: Jeffrey Walton <noloader@gmail.com>
Cc: stable@vger.kernel.org
Cc: "H. Peter Anvin" <hpa@zytor.com>
Link: https://lkml.kernel.org/r/20180424212013.3967461-1-arnd@arndb.de
