88E6250-family switches have the quirk that the EEPROM Running flag can
get stuck at 1 when no EEPROM is connected, causing
mv88e6xxx_g2_eeprom_wait() to time out. We still want to wait for the
EEPROM however, to avoid interrupting a transfer and leaving the EEPROM
in an invalid state.
The condition to wait for recommended by the hardware spec is the EEInt
flag, however this flag is cleared on read, so before the hardware reset,
is may have been cleared already even though the EEPROM has been read
successfully.
For this reason, we revive the mv88e6xxx_g1_wait_eeprom_done() function
that was removed in commit 6ccf50d4d474
("net: dsa: mv88e6xxx: Avoid EEPROM timeout when EEPROM is absent") in a
slightly refactored form, and introduce a new
mv88e6xxx_g1_wait_eeprom_done_prereset() that additionally handles this
case by triggering another EEPROM reload that can be waited on.
On other switch models without this quirk, mv88e6xxx_g2_eeprom_wait() is
kept, as it avoids the additional reload.
Fixes: 6ccf50d4d474 ("net: dsa: mv88e6xxx: Avoid EEPROM timeout when EEPROM is absent")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of calling mv88e6xxx_g2_eeprom_wait() directly from
mv88e6xxx_hardware_reset(), add configurable pre- and post-reset hard
reset handlers. Initially, the handlers are set to
mv88e6xxx_g2_eeprom_wait() for all families that have get/set_eeprom()
to match the existing behavior. No functional change intended (except
for additional error messages on failure).
Fixes: 6ccf50d4d474 ("net: dsa: mv88e6xxx: Avoid EEPROM timeout when EEPROM is absent")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the hardcoded values used in the calculations for
vnic descriptors and rings with defines. Minor code cleanup.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Philo Lu says:
====================
tcp: update TCPCB_EVER_RETRANS after trace_tcp_retransmit_skb()
Move TCPCB_EVER_RETRANS updating after the trace_tcp_retransmit_skb()
in __tcp_retransmit_skb(), and then we are aware of whether the skb has
ever been retransmitted in this tracepoint. This can be used, e.g., to get
retransmission efficiency by counting skbs w/ and w/o TCPCB_EVER_RETRANS
(through bpf tracing programs).
For this purpose, TCPCB_EVER_RETRANS is also needed to be exposed to bpf.
Previously, the flags are defined as macros in struct tcp_skb_cb. I moved them
out into a new enum, and then they can be accessed with vmlinux.h.
We have discussed to achieve this with BPF_SOCK_OPS in [0], and using
tracepoint is thought to be a better solution.
[0]
https://lore.kernel.org/all/20240417124622.35333-1-lulie@linux.alibaba.com/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Marking TCP_SKB_CB(skb)->sacked with TCPCB_EVER_RETRANS after the
traceopint (trace_tcp_retransmit_skb), then we can get the
retransmission efficiency by counting skbs w/ and w/o TCPCB_EVER_RETRANS
mark in this tracepoint.
We have discussed to achieve this with BPF_SOCK_OPS in [0], and using
tracepoint is thought to be a better solution.
[0]
https://lore.kernel.org/all/20240417124622.35333-1-lulie@linux.alibaba.com/
Signed-off-by: Philo Lu <lulie@linux.alibaba.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the flag definitions for tcp_skb_cb->sacked into a new enum named
tcp_skb_cb_sacked_flags, then we can get access to them in bpf via
vmlinux.h, e.g., in tracepoints.
This patch does not change any existing functionality.
Signed-off-by: Philo Lu <lulie@linux.alibaba.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski says:
====================
selftests: net: extract BPF building logic from the Makefile
This has been sitting in my tree for a while. I will soon add YNL/libynl
support for networking selftests. This prompted a small cleanup of
the selftest makefile for net/. We don't want to be piling logic
for each library in there. YNL will get its own .mk file which can
be included. Do the same for the BPF building section, already.
No funcional changes here, just a code move and small rename.
====================
Link: https://lore.kernel.org/r/20240423183542.3807234-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The BPF sample building code looks a little bit spaghetti-ish
so move it out to its own Makefile snippet. Similar in the spirit
to how we include lib.mk. libynl will soon get a similar snippet.
There is a small change hiding in the move, the relative
paths (../../.., ../.. etc) are replaced with variables
from lib.mk such as top_srcdir and selfdir.
Link: https://lore.kernel.org/r/20240423183542.3807234-3-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The BPF sources moved with bpf_offload.py have a suffix of .bpf.c
which seems to be useful convention. Rename the 2 other BPF sources
we had. Use wildcard in the Makefile, since we can match all those
files easily now.
Link: https://lore.kernel.org/r/20240423183542.3807234-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Clarify PSE regulator as voltage regulator, not current.
The PSE (Power Sourcing Equipment) regulator is defined as a voltage
regulator, maintaining fixed voltage while accommodating varying current.
Fixes: d83e13761d5b ("net: pse-pd: Use regulator framework within PSE framework")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://lore.kernel.org/r/20240423-fix_poe-v3-2-e50f32f5fa59@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add missing kernel documentation return description.
This allows to remove all warning from kernel-doc test script.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://lore.kernel.org/r/20240423-fix_poe-v3-1-e50f32f5fa59@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
ice: Support 5 layer Tx scheduler topology
Mateusz Polchlopek says:
For performance reasons there is a need to have support for selectable
Tx scheduler topology. Currently firmware supports only the default
9-layer and 5-layer topology. This patch series enables switch from
default to 5-layer topology, if user decides to opt-in.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
ice: Document tx_scheduling_layers parameter
ice: Add tx_scheduling_layers devlink param
ice: Enable switching default Tx scheduler topology
ice: Adjust the VSI/Aggregator layers
ice: Support 5 layer topology
devlink: extend devlink_param *set pointer
====================
Link: https://lore.kernel.org/r/20240422203913.225151-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use flow_rule_is_supp_control_flags() to reject filters with
unsupported control flags.
In case any unsupported control flags are masked,
flow_rule_is_supp_control_flags() sets a NL extended
error message, and we return -EOPNOTSUPP.
Remove FLOW_DIS_FIRST_FRAG specific error message,
and treat it as any other unsupported control flag.
Only compile-tested.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Sunil Goutham <sgoutham@marvell.com>
Link: https://lore.kernel.org/r/20240422152735.175693-1-ast@fiberby.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This driver currently doesn't support any control flags.
Use flow_rule_has_control_flags() to check for control flags,
such as can be set through `tc flower ... ip_flags frag`.
In case any control flags are masked, flow_rule_has_control_flags()
sets a NL extended error message, and we return -EOPNOTSUPP.
Also propagate extack to hclge_get_cls_key_ip(), and convert it to
return error code.
Only compile-tested.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Tested-by: Jijie Shao <shaojijie@huawei.com>
Link: https://lore.kernel.org/r/20240422152717.175659-1-ast@fiberby.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This driver currently doesn't support any control flags.
Use flow_rule_match_has_control_flags() to check for control flags,
such as can be set through `tc flower ... ip_flags frag`.
In case any control flags are masked, flow_rule_match_has_control_flags()
sets a NL extended error message, and we return -EOPNOTSUPP.
Only compile-tested.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20240422152656.175627-1-ast@fiberby.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This driver currently doesn't support any control flags.
Use flow_rule_match_has_control_flags() to check for control flags,
such as can be set through `tc flower ... ip_flags frag`.
In case any control flags are masked, flow_rule_match_has_control_flags()
sets a NL extended error message, and we return -EOPNOTSUPP.
Only compile-tested.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20240422152643.175592-1-ast@fiberby.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This driver currently doesn't support any control flags.
Use flow_rule_match_has_control_flags() to check for control flags,
such as can be set through `tc flower ... ip_flags frag`.
In case any control flags are masked, flow_rule_match_has_control_flags()
sets a NL extended error message, and we return -EOPNOTSUPP.
Only compile-tested.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Tested-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Link: https://lore.kernel.org/r/20240422152626.175569-1-ast@fiberby.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
TI's J784S4 SoC supports SGMII mode with CPSW9G instance of the CPSW
Ethernet Switch. Thus, enable it by adding SGMII mode to the
extra_modes member of the "j784s4_cpswxg_pdata" SoC data.
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
Link: https://lore.kernel.org/r/20240422124515.887511-1-c-vankar@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
nf_conntrack_udp_timeout sysctl only exist once conntrack module is loaded,
if this test runs standalone on a modular kernel sysctl setting fails,
this can result in test failure as udp conntrack entries expire too fast.
Signed-off-by: Florian Westphal <fw@strlen.de>
Link: https://lore.kernel.org/r/20240422102546.2494-1-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Florian Westphal says:
====================
selftest: netfilter: additional cleanups
This is the last planned series of the netfilter-selftest-move.
It contains cleanups (and speedups) and a few small updates to
scripts to improve error/skip reporting.
I intend to route future changes, if any, via nf(-next) trees
now that the 'massive code churn' phase is over.
====================
Link: https://lore.kernel.org/r/20240423130604.7013-1-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use socat, like most of the other scripts already do. This also makes
the script complete slightly faster (3s -> 1s).
iperf3 establishes two connections (1 control connection, and 1+x
depending on test), so adjust expected counter values as well.
Signed-off-by: Florian Westphal <fw@strlen.de>
Link: https://lore.kernel.org/r/20240423130604.7013-8-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
br_netfilter: If we can't add the needed initial nftables ruleset skip the
test, kernel doesn't support a required feature.
rpath: run a subset of the tests if possible, but make sure we return
the skip return value so they are marked appropriately by the kselftest
framework.
nft_audit.sh: provide version information when skipping, this should
help catching kernel problem (feature not available in kernel) vs.
userspace issue (parser doesn't support keyword).
Signed-off-by: Florian Westphal <fw@strlen.de>
Link: https://lore.kernel.org/r/20240423130604.7013-7-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
no functional changes intended except that test will now SKIP in
case kernel lacks bridge support and initial rule load failure provides
nft version information.
Signed-off-by: Florian Westphal <fw@strlen.de>
Link: https://lore.kernel.org/r/20240423130604.7013-6-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that the test runs much faster, also re-run it with random MTU sizes
for the different link legs. flowtable should pass ip fragments, if
any, up to the normal forwarding path.
Signed-off-by: Florian Westphal <fw@strlen.de>
Link: https://lore.kernel.org/r/20240423130604.7013-5-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tests fail on my workstation with netcat 110, instead of debugging+more
workarounds just remove this.
Tests will fall back to bash or socat.
Signed-off-by: Florian Westphal <fw@strlen.de>
Link: https://lore.kernel.org/r/20240423130604.7013-3-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use busywait helper instead of unconditional sleep, reduces run time
from 6m to 2:30 on my system.
The busywait helper calls the function passed to it as argument; disable
the shellcheck test for unreachable code, it generates many (false)
warnings here.
Signed-off-by: Florian Westphal <fw@strlen.de>
Link: https://lore.kernel.org/r/20240423130604.7013-2-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
dev_get_by_name will provide a reference on the netdev. So ensure that
the reference of netdev is released after completed.
Fixes: 2540088b836f ("net: openvswitch: Check vport netdev name")
Signed-off-by: Jun Gu <jun.gu@easystack.cn>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Link: https://lore.kernel.org/r/20240423073751.52706-1-jun.gu@easystack.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Daniel Machon says:
====================
net: sparx5: add support for port mirroring
This series adds support for port mirroring, and port mirroring stats,
through tc matchall action FLOW_ACTION_MIRRED.
The hardware has three independent mirroring probes. Each probe can be
configured with a separate set of filtering conditions that must be
fulfilled before traffic is mirrored.
A mirror probe can have up to 64 source ports and a single monitor port.
The direction of a mirror probe determines if rx or tx traffic is
mirrored from the source port to the monitor port.
To: David S. Miller <davem@davemloft.net>
To: Eric Dumazet <edumazet@google.com>
To: Jakub Kicinski <kuba@kernel.org>
To: Paolo Abeni <pabeni@redhat.com>
To: Lars Povlsen <lars.povlsen@microchip.com>
To: Steen Hegelund <Steen.Hegelund@microchip.com>
To: UNGLinuxDriver@microchip.com
To: Russell King <linux@armlinux.org.uk>
Cc: netdev@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: Horatiu Vultur <horatiu.vultur@microchip.com>
Cc: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
Cc: Yue Haibing <yuehaibing@huawei.com>
---
Changes in v3:
- Ditch do_div() (patch #3) to fix warning on hexagon arch, reported by intel bot
- Link to v2: https://lore.kernel.org/r/20240418-port-mirroring-v2-0-20642868b386@microchip.com
Changes in v2:
- Fix clang build warning about uninitialized variable 'err'
- Link to v1: https://lore.kernel.org/r/20240418-port-mirroring-v1-0-e05c35007c55@microchip.com
====================
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for tc matchall mirror stats. When a new matchall mirror
rule is added, the baseline stats for that port is saved.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the necessary tc glue to add and delete mirror rules through tc
matchall.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware supports three independent mirroring probes. Each probe can
be configured to mirror rx or tx traffic (direction).
Using tc matchall, it is now possible to add a source port and a monitor
port to a mirror probe. Depending on the mirror direction, rx or tx
traffic from a source port will be mirrored to the monitor port.
A single source port can be a member of multiple mirror probes.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for new tc matchall rules, we add a bit of bookkeeping
code to keep track of them. The rules are identified by the cookie
passed from the tc stack.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for port mirroring support through tc matchall, add the
required register definitions.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Breno Leitao says:
====================
allocate dummy device dynamically
struct net_device shouldn't be embedded into any structure, instead,
the owner should use the private space to embed their state into
net_device.
But, in some cases the net_device is embedded inside the private
structure, which blocks the usage of zero-length arrays inside
net_device.
Create a helper to allocate a dummy device at dynamically runtime, and
move the Ethernet devices to use it, instead of embedding the dummy
device inside the private structure.
This fixes all the network cases plus some wireless drivers.
PS: Due to lack of hardware, unfortunately most these patches are
compiled tested only, except ath11k that was kindly tested by Kalle Valo.
---
Changelog:
v7:
* Document the return value of alloc_netdev_dummy()
v6:
* No code change. Just added Reviewed-by: and fix a commit message
v5:
* Added a new patch to fix some typos in the previous code
* Rebased to net-net/main
v4:
* Added a new patch to add dummy device at free_netdev(), as suggested
by Jakub.
* Added support for some wireless driver.
* Added some Acked-by and Reviewed-by.
v3:
* Use free_netdev() instead of kfree() as suggested by Jakub.
* Change the free_netdev() place in ipa driver, as suggested by
Alex Elder.
* Set err in the error path in the Marvell driver, as suggested
by Simon Horman.
v2:
* Patch 1: Use a pre-defined name ("dummy#") for the dummy
net_devices.
* Patch 2-5: Added users for the new helper.
v1:
* https://lore.kernel.org/all/20240327200809.512867-1-leitao@debian.org/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Embedding net_device into structures prohibits the usage of flexible
arrays in the net_device structure. For more details, see the discussion
at [1].
Un-embed the net_device from struct ath11k_ext_irq_grp by converting it
into a pointer. Then use the leverage alloc_netdev() to allocate the
net_device object at ath11k_ahb_config_ext_irq() for ahb, and
ath11k_pcic_ext_irq_config() for pcic.
The free of the device occurs at ath11k_ahb_free_ext_irq() for the ahb
case, and ath11k_pcic_free_ext_irq() for the pcic case.
[1] https://lore.kernel.org/all/20240229225910.79e224cf@kernel.org/
Signed-off-by: Breno Leitao <leitao@debian.org>
Tested-by: Kalle Valo <kvalo@kernel.org>
Acked-by: Kalle Valo <kvalo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Embedding net_device into structures prohibits the usage of flexible
arrays in the net_device structure. For more details, see the discussion
at [1].
Un-embed the net_device from struct ath10k by converting it
into a pointer. Then use the leverage alloc_netdev() to allocate the
net_device object at ath10k_core_create(). The free of the device occurs
at ath10k_core_destroy().
[1] https://lore.kernel.org/all/20240229225910.79e224cf@kernel.org/
Signed-off-by: Breno Leitao <leitao@debian.org>
Acked-by: Kalle Valo <kvalo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a new dummy netdev allocator, use it instead of
alloc_netdev()/init_dummy_netdev combination.
Using alloc_netdev() with init_dummy_netdev might cause some memory
corruption at the driver removal side.
Fixes: 61cdb09ff760 ("wifi: qtnfmac: allocate dummy net_device dynamically")
Signed-off-by: Breno Leitao <leitao@debian.org>
Acked-by: Kalle Valo <kvalo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Embedding net_device into structures prohibits the usage of flexible
arrays in the net_device structure. For more details, see the discussion
at [1].
Un-embed the net_device from the private struct by converting it
into a pointer. Then use the leverage the new alloc_netdev_dummy()
helper to allocate and initialize dummy devices.
[1] https://lore.kernel.org/all/20240229225910.79e224cf@kernel.org/
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Embedding net_device into structures prohibits the usage of flexible
arrays in the net_device structure. For more details, see the discussion
at [1].
Un-embed the net_device from the private struct by converting it
into a pointer. Then use the leverage the new alloc_netdev_dummy()
helper to allocate and initialize dummy devices.
[1] https://lore.kernel.org/all/20240229225910.79e224cf@kernel.org/
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Embedding net_device into structures prohibits the usage of flexible
arrays in the net_device structure. For more details, see the discussion
at [1].
Un-embed the net_device from the private struct by converting it
into a pointer. Then use the leverage the new alloc_netdev_dummy()
helper to allocate and initialize dummy devices.
[1] https://lore.kernel.org/all/20240229225910.79e224cf@kernel.org/
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Embedding net_device into structures prohibits the usage of flexible
arrays in the net_device structure. For more details, see the discussion
at [1].
Un-embed the net_device from the private struct by converting it
into a pointer. Then use the leverage the new alloc_netdev_dummy()
helper to allocate and initialize dummy devices.
[1] https://lore.kernel.org/all/20240229225910.79e224cf@kernel.org/
Signed-off-by: Breno Leitao <leitao@debian.org>
Acked-by: Elad Nachman <enachman@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is impossible to use init_dummy_netdev together with alloc_netdev()
as the 'setup' argument.
This is because alloc_netdev() initializes some fields in the net_device
structure, and later init_dummy_netdev() memzero them all. This causes
some problems as reported here:
https://lore.kernel.org/all/20240322082336.49f110cc@kernel.org/
Split the init_dummy_netdev() function in two. Create a new function called
init_dummy_netdev_core() that does not memzero the net_device structure.
Then have init_dummy_netdev() memzero-ing and calling
init_dummy_netdev_core(), keeping the old behaviour.
init_dummy_netdev_core() is the new function that could be called as an
argument for alloc_netdev().
Also, create a helper to allocate and initialize dummy net devices,
leveraging init_dummy_netdev_core() as the setup argument. This function
basically simplify the allocation of dummy devices, by allocating and
initializing it. Freeing the device continue to be done through
free_netdev()
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For dummy devices, exit earlier at free_netdev() instead of executing
the whole function. This is necessary, because dummy devices are
special, and shouldn't have the second part of the function executed.
Otherwise reg_state, which is NETREG_DUMMY, will be overwritten and
there will be no way to identify that this is a dummy device. Also, this
device do not need the final put_device(), since dummy devices are not
registered (through register_netdevice()), where the device reference is
increased (at netdev_register_kobject()/device_add()).
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix bad grammar in description of init_dummy_netdev() function. This
topic showed up in the review of the "allocate dummy device dynamically"
patch set.
Suggested-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arınç ÜNAL says:
====================
MT7530 DSA Subdriver Improvements Act IV
This is the forth patch series with the goal of simplifying the MT7530 DSA
subdriver and improving support for MT7530, MT7531, and the switch on the
MT7988 SoC.
I have done a simple ping test to confirm basic communication on all switch
ports on MCM and standalone MT7530, and MT7531 switch with this patch
series applied.
MT7621 Unielec, MCM MT7530:
rgmii-only-gmac0-mt7621-unielec-u7621-06-16m.dtb
gmac0-and-gmac1-mt7621-unielec-u7621-06-16m.dtb
tftpboot 0x80008000 mips-uzImage.bin; tftpboot 0x83000000 mips-rootfs.cpio.uboot; tftpboot 0x83f00000 $dtb; bootm 0x80008000 0x83000000 0x83f00000
MT7622 Bananapi, MT7531:
gmac0-and-gmac1-mt7622-bananapi-bpi-r64.dtb
tftpboot 0x40000000 arm64-Image; tftpboot 0x45000000 arm64-rootfs.cpio.uboot; tftpboot 0x4a000000 $dtb; booti 0x40000000 0x45000000 0x4a000000
MT7623 Bananapi, standalone MT7530:
rgmii-only-gmac0-mt7623n-bananapi-bpi-r2.dtb
gmac0-and-gmac1-mt7623n-bananapi-bpi-r2.dtb
tftpboot 0x80008000 arm-zImage; tftpboot 0x83000000 arm-rootfs.cpio.uboot; tftpboot 0x83f00000 $dtb; bootz 0x80008000 0x83000000 0x83f00000
This patch series finalises the patch series linked below.
https://lore.kernel.org/r/20230522121532.86610-1-arinc.unal@arinc9.com
---
Changes in v2:
- Add two new patches to the end.
- Patch 13
- Add the missing patch log.
- Link to v1: https://lore.kernel.org/r/20240419-for-netnext-mt7530-improvements-4-v1-0-6d852ca79b1d@arinc9.com
====================
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike MT7531BE, the GPIO 6-12 pins are not used for RGMII on MT7531AE.
Therefore, the GPIO 11-12 pins are set to function as MDC and MDIO to
expose the MDIO bus of the switch. Replace the comment with a better
explanation.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mt7531_rgmii_setup() function does not use the port variable, do not
pass the variable to it.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
