If the clock sehci->clk was not enabled in spear_ehci_hcd_drv_probe,
it should not be disabled in any path.
Conversely, if it was enabled in spear_ehci_hcd_drv_probe, it must be disabled
in all error paths to ensure proper cleanup.
Found by Linux Verification Center (linuxtesting.org) with Klever.
Fixes: 7675d6ba43 ("USB: EHCI: make ehci-spear a separate driver")
Cc: stable@vger.kernel.org
Signed-off-by: Vitalii Mordan <mordan@ispras.ru>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20241114230310.432213-1-mordan@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are the USB-serial updates for 6.13-rc1, including:
- improved support for quirky pl2303 hxd devices
- make sure ftdi_sio TIOCGSERIAL returns consistent data
Everything has been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCZzdTXQAKCRALxc3C7H1l
COSGAP0U6gSnhn9V6cSzz9WVJwfAAifKkBB6ZvPORmOX4f5nMwEAtEEQJQtdCXD6
d/9/9hEF1Xot5nhKfOTtFMbwWM+rtgI=
=gbhm
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-6.13-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for 6.13-rc1
Here are the USB-serial updates for 6.13-rc1, including:
- improved support for quirky pl2303 hxd devices
- make sure ftdi_sio TIOCGSERIAL returns consistent data
Everything has been in linux-next with no reported issues.
* tag 'usb-serial-6.13-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: ftdi_sio: Fix atomicity violation in get_serial_info()
USB: serial: pl2303: account for deficits of clones
Turns out that we have some const pointers being passed to
to_usb_device_driver() but were not catching this. Change the macro to
properly propagate the const-ness of the pointer so that we will notice
when we try to write to memory that we shouldn't be writing to.
This requires fixing up the usb_driver_applicable() function as well,
because it can handle a const * to struct usb_driver.
Cc: Johan Hovold <johan@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Grant Grundler <grundler@chromium.org>
Cc: Yajun Deng <yajun.deng@linux.dev>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: linux-usb@vger.kernel.org
Link: https://lore.kernel.org/r/2024111342-lagoon-reapprove-5e49@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Turns out that we have some const pointers being passed to
to_usb_driver() but were not catching this. Change the macro to
properly propagate the const-ness of the pointer so that we will notice
when we try to write to memory that we shouldn't be writing to.
This requires fixing up the usb_match_dynamic_id() function as well,
because it can handle a const * to struct usb_driver.
Cc: Johan Hovold <johan@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Grant Grundler <grundler@chromium.org>
Cc: Yajun Deng <yajun.deng@linux.dev>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: linux-usb@vger.kernel.org
Link: https://lore.kernel.org/r/2024111339-shaky-goldsmith-b233@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When walking the list of dynamic ids for a driver, no lock was being
held, which meant that an id could be removed or added while the list
was being iterated. Fix this up by properly grabing the lock while we
walk the list.
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Cc: linux-usb@vger.kernel.org
Link: https://lore.kernel.org/r/2024111324-tubby-facecloth-d4a0@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a number of places where we accidentally pass in a constant
structure to later cast it off to a dynamic one, and then attempt to
grab a lock on it, which is not a good idea. To help resolve this, move
the dynamic id lock out of the dynamic id structure for the driver and
into one single lock for all USB dynamic ids. As this lock should never
have any real contention (it's only every accessed when a device is
added or removed, which is always serialized) there should not be any
difference except for some memory savings.
Note, this just converts the existing use of the dynamic id lock to the
new static lock, there is one place that is accessing the dynamic id
list without grabbing the lock, that will be fixed up in a follow-on
change.
Cc: Johan Hovold <johan@kernel.org>
Cc: Herve Codina <herve.codina@bootlin.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Grant Grundler <grundler@chromium.org>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Yajun Deng <yajun.deng@linux.dev>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: linux-usb@vger.kernel.org
Link: https://lore.kernel.org/r/2024111322-kindly-finalist-d247@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ensure type safety by using min_t() instead of min().
Also add the explicit `unsigned int` as scripts/checkpatch.pl warns about:
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
Signed-off-by: Sabyrzhan Tasbolatov <snovitoll@gmail.com>
Link: https://lore.kernel.org/r/20241112155817.3512577-5-snovitoll@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a few places in the kernel where PCI IDs for different Cadence
USB controllers are being used. Besides different naming, they duplicate
each other. Make this all in order by providing common definitions via
PCI IDs database and use in all users. While doing that, rename
definitions as Roger suggested.
Suggested-by: Roger Quadros <rogerq@kernel.org>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20241112160125.2340972-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently if the maximum-speed is set to Super Speed for a 3.1 Gen2
capable controller, the FORCE_GEN1 bit of LLUCTL register is set only
for one SuperSpeed port (or the first port) present. Modify the logic
to set the FORCE_GEN1 bit for all ports if speed is being limited to
Gen-1.
Suggested-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20241112182018.199392-1-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The existing implementation of the TxFIFO resizing logic only supports
scenarios where more than one port RAM is used. However, there is a need
to resize the TxFIFO in USB2.0-only mode where only a single port RAM is
available. This commit introduces the necessary changes to support
TxFIFO resizing in such scenarios by adding a missing check for single
port RAM.
This fix addresses certain platform configurations where the existing
TxFIFO resizing logic does not work properly due to the absence of
support for single port RAM. By adding this missing check, we ensure
that the TxFIFO resizing logic works correctly in all scenarios,
including those with a single port RAM.
Fixes: 9f607a309f ("usb: dwc3: Resize TX FIFOs to meet EP bursting requirements")
Cc: stable@vger.kernel.org # 6.12.x: fad16c82: usb: dwc3: gadget: Refine the logic for resizing Tx FIFOs
Signed-off-by: Selvarasu Ganesan <selvarasu.g@samsung.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20241112044807.623-1-selvarasu.g@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "command" variable can be controlled by the user via debugfs. The
worry is that if con_index is zero then "&uc->ucsi->connector[con_index
- 1]" would be an array underflow.
Fixes: 170a6726d0 ("usb: typec: ucsi: add support for separate DP altmode devices")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/c69ef0b3-61b0-4dde-98dd-97b97f81d912@stanley.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some Lenovo platforms, the patch works around problems with ov2740
sensor initialization, which manifest themself like below:
[ 4.540476] ov2740 i2c-INT3474:01: error -EIO: failed to find sensor
[ 4.542066] ov2740 i2c-INT3474:01: probe with driver ov2740 failed with error -5
or
[ 7.742633] ov2740 i2c-INT3474:01: chip id mismatch: 2740 != 0
[ 7.742638] ov2740 i2c-INT3474:01: error -ENXIO: failed to find sensor
and also by random failures of video stream start.
Issue can be reproduced by this script:
n=0
k=0
while [ $n -lt 50 ] ; do
sudo modprobe -r ov2740
sleep `expr $RANDOM % 5`
sudo modprobe ov2740
if media-ctl -p | grep -q ov2740 ; then
let k++
fi
let n++
done
echo Success rate $k/$n
Without the patch, success rate is approximately 15 or 50 tries.
With the patch it does not fail.
This problem is some hardware or firmware malfunction, that can not be
easy debug and fix. While setting small autosuspend delay is not perfect
workaround as user can configure it to any value, it will prevent
the failures by default.
Additionally setting small autosuspend delay should have positive effect
on power consumption as for most ljca workloads device is used for just
a few milliseconds flowed by long periods of at least 100ms of inactivity
(usually more).
Fixes: acd6199f19 ("usb: Add support for Intel LJCA device")
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com> # ThinkPad X1 Yoga Gen 8, ov2740
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://lore.kernel.org/r/20241112075514.680712-2-stanislaw.gruszka@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not mark interface as ready to suspend when we are still waiting
for response messages from the device.
Fixes: acd6199f19 ("usb: Add support for Intel LJCA device")
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com> # ThinkPad X1 Yoga Gen 8, ov2740
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://lore.kernel.org/r/20241112075514.680712-1-stanislaw.gruszka@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dtbinding have imx7ulp and imx8ulp compatible with imx7d before. And
then the dtb follow the dtbinding. However, the driver doesn't add imx8ulp
compatible now. To make imx8ulp work well, this will add support for it.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20241111090916.1534047-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The GET_CAPABILITY size is wrong. The definitions for the
command sizes are for bitfieds and therefore in bits, not
bytes.
This fixes an issue that prevents the interface from being
registered with UCSI versions older than 2.0 because the
command size exceeds the MESSAGE_IN field size.
Fixes: 226ff2e681 ("usb: typec: ucsi: Convert connector specific commands to bitmaps")
Reported-by: Abel Vesa <abel.vesa@linaro.org>
Closes: https://lore.kernel.org/linux-usb/Zy864W7sysWZbCTd@linaro.org/
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Tested-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20241111100220.1743872-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a possibility that a request's callback could be invoked from
usb_ep_queue() (call trace below, supplemented with missing calls):
req->complete from usb_gadget_giveback_request
(drivers/usb/gadget/udc/core.c:999)
usb_gadget_giveback_request from musb_g_giveback
(drivers/usb/musb/musb_gadget.c:147)
musb_g_giveback from rxstate
(drivers/usb/musb/musb_gadget.c:784)
rxstate from musb_ep_restart
(drivers/usb/musb/musb_gadget.c:1169)
musb_ep_restart from musb_ep_restart_resume_work
(drivers/usb/musb/musb_gadget.c:1176)
musb_ep_restart_resume_work from musb_queue_resume_work
(drivers/usb/musb/musb_core.c:2279)
musb_queue_resume_work from musb_gadget_queue
(drivers/usb/musb/musb_gadget.c:1241)
musb_gadget_queue from usb_ep_queue
(drivers/usb/gadget/udc/core.c:300)
According to the docstring of usb_ep_queue(), this should not happen:
"Note that @req's ->complete() callback must never be called from within
usb_ep_queue() as that can create deadlock situations."
In fact, a hardware lockup might occur in the following sequence:
1. The gadget is initialized using musb_gadget_enable().
2. Meanwhile, a packet arrives, and the RXPKTRDY flag is set, raising an
interrupt.
3. If IRQs are enabled, the interrupt is handled, but musb_g_rx() finds an
empty queue (next_request() returns NULL). The interrupt flag has
already been cleared by the glue layer handler, but the RXPKTRDY flag
remains set.
4. The first request is enqueued using usb_ep_queue(), leading to the call
of req->complete(), as shown in the call trace above.
5. If the callback enables IRQs and another packet is waiting, step (3)
repeats. The request queue is empty because usb_g_giveback() removes the
request before invoking the callback.
6. The endpoint remains locked up, as the interrupt triggered by hardware
setting the RXPKTRDY flag has been handled, but the flag itself remains
set.
For this scenario to occur, it is only necessary for IRQs to be enabled at
some point during the complete callback. This happens with the USB Ethernet
gadget, whose rx_complete() callback calls netif_rx(). If called in the
task context, netif_rx() disables the bottom halves (BHs). When the BHs are
re-enabled, IRQs are also enabled to allow soft IRQs to be processed. The
gadget itself is initialized at module load (or at boot if built-in), but
the first request is enqueued when the network interface is brought up,
triggering rx_complete() in the task context via ioctl(). If a packet
arrives while the interface is down, it can prevent the interface from
receiving any further packets from the USB host.
The situation is quite complicated with many parties involved. This
particular issue can be resolved in several possible ways:
1. Ensure that callbacks never enable IRQs. This would be difficult to
enforce, as discovering how netif_rx() interacts with interrupts was
already quite challenging and u_ether is not the only function driver.
Similar "bugs" could be hidden in other drivers as well.
2. Disable MUSB interrupts in musb_g_giveback() before calling the callback
and re-enable them afterwars (by calling musb_{dis,en}able_interrupts(),
for example). This would ensure that MUSB interrupts are not handled
during the callback, even if IRQs are enabled. In fact, it would allow
IRQs to be enabled when releasing the lock. However, this feels like an
inelegant hack.
3. Modify the interrupt handler to clear the RXPKTRDY flag if the request
queue is empty. While this approach also feels like a hack, it wastes
CPU time by attempting to handle incoming packets when the software is
not ready to process them.
4. Flush the Rx FIFO instead of calling rxstate() in musb_ep_restart().
This ensures that the hardware can receive packets when there is at
least one request in the queue. Once IRQs are enabled, the interrupt
handler will be able to correctly process the next incoming packet
(eventually calling rxstate()). This approach may cause one or two
packets to be dropped (two if double buffering is enabled), but this
seems to be a minor issue, as packet loss can occur when the software is
not yet ready to process them. Additionally, this solution makes the
gadget driver compliant with the rule mentioned in the docstring of
usb_ep_queue().
There may be additional solutions, but from these four, the last one has
been chosen as it seems to be the most appropriate, as it addresses the
"bad" behavior of the driver.
Fixes: baebdf48c3 ("net: dev: Makes sure netif_rx() can be invoked in any context.")
Cc: stable@vger.kernel.org
Signed-off-by: Hubert Wiśniewski <hubert.wisniewski.25632@gmail.com>
Link: https://lore.kernel.org/r/4ee1ead4525f78fb5909a8cbf99513ad0082ad21.camel@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of checking if any of the USB-C ports have orientation GPIO and
thus is orientation-aware, check for the GPIO for the port being
registered. There are no boards that are affected by this change at this
moment, so the patch is not marked as a fix, but it might affect other
boards in future.
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241109-ucsi-glue-fixes-v2-2-8b21ff4f9fbe@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UCSI connector's indices start from 1 up to 3, PMIC_GLINK_MAX_PORTS.
Correct the condition in the pmic_glink_ucsi_connector_status()
callback, fixing Type-C orientation reporting for the third USB-C
connector.
Fixes: 76716fd5bf ("usb: typec: ucsi: glink: move GPIO reading into connector_status callback")
Cc: stable@vger.kernel.org
Reported-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241109-ucsi-glue-fixes-v2-1-8b21ff4f9fbe@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After an initial range change on the insigned int alt being > 1
the only possible values for alt are 0 or 1. Therefore the else
statement for values other than 0 or 1 is redundant and can be
removed. Replace the else if (all == 1) check with just an else.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/5f54ffd0-b5fe-4203-a626-c166becad362@gmail.com
Link: https://lore.kernel.org/r/20241107133348.22762-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's a fix for a long-standing use-after-free in an io_edgeport debug
printk and some new modem device ids.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCZy29qQAKCRALxc3C7H1l
CKN8AP9hD+7glW6sf0JDJ3zcN9vPIn1NLqALMil7Ga8hrmy2wQD/ff/mBrJqugF+
pQ1nFCQzLR2LtQEWRm/5ebb9yeaE1gE=
=3wbn
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-6.12-rc7' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 6.12-rc7
Here's a fix for a long-standing use-after-free in an io_edgeport debug
printk and some new modem device ids.
All have been in linux-next with no reported issues.
* tag 'usb-serial-6.12-rc7' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: qcserial: add support for Sierra Wireless EM86xx
USB: serial: io_edgeport: fix use after free in debug printk
USB: serial: option: add Quectel RG650V
USB: serial: option: add Fibocom FG132 0x0112 composition
Our static checker found a bug where set_serial_info() uses a mutex, but
get_serial_info() does not. Fortunately, the impact of this is relatively
minor. It doesn't cause a crash or any other serious issues. However, if a
race condition occurs between set_serial_info() and get_serial_info(),
there is a chance that the data returned by get_serial_info() will be
inconsistent.
Fixes: 3ae36bed3a ("fdti_sio: switch to ->[sg]et_serial()")
Signed-off-by: Qiu-ji Chen <chenqiuji666@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
That allows the fields in those command data structures to
be easily validated. If an unsupported field is accessed, a
warning is generated.
This will not force UCSI version checks to be made in every
place where these data structures are accessed, but it will
make it easier to pinpoint issues that are caused by the
unconditional accesses to those fields, and perhaps more
importantly, allow those issues to be noticed immediately.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241106150605.1017744-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are apparently incomplete clones of the HXD type chip in use.
Those return -EPIPE on GET_LINE_REQUEST and BREAK_REQUEST. Avoid
flooding the kernel log with those errors. Detect them during startup
and then use the line_settings cache instead of GET_LINE_REQUEST. Signal
missing break support via -ENOTTY.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
[ johan: fix macro prefix, drop oom error message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Stop Endpoint command on an already stopped endpoint fails and may be
misinterpreted as a known hardware bug by the completion handler. This
results in an unnecessary delay with repeated retries of the command.
Avoid queuing this command when endpoint state flags indicate that it's
stopped or halted and the command will fail. If commands are pending on
the endpoint, their completion handlers will process cancelled TDs so
it's done. In case of waiting for external operations like clearing TT
buffer, the endpoint is stopped and cancelled TDs can be processed now.
This eliminates practically all unnecessary retries because an endpoint
with pending URBs is maintained in Running state by the driver, unless
aforementioned commands or other operations are pending on it. This is
guaranteed by xhci_ring_ep_doorbell() and by the fact that it is called
every time any of those operations completes.
The only known exceptions are hardware bugs (the endpoint never starts
at all) and Stream Protocol errors not associated with any TRB, which
cause an endpoint reset not followed by restart. Sounds like a bug.
Generally, these retries are only expected to happen when the endpoint
fails to start for unknown/no reason, which is a worse problem itself,
and fixing the bug eliminates the retries too.
All cases were tested and found to work as expected. SET_DEQ_PENDING
was produced by patching uvcvideo to unlink URBs in 100us intervals,
which then runs into this case very often. EP_HALTED was produced by
restarting 'cat /dev/ttyUSB0' on a serial dongle with broken cable.
EP_CLEARING_TT by the same, with the dongle on an external hub.
Fixes: fd9d55d190 ("xhci: retry Stop Endpoint on buggy NEC controllers")
CC: stable@vger.kernel.org
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-34-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_invalidate_cancelled_tds() may not work correctly if the hardware
is modifying endpoint or stream contexts at the same time by executing
a Set TR Dequeue command. And even if it worked, it would be unable to
queue Set TR Dequeue for the next stream, failing to clear xHC cache.
On stream endpoints, a chain of Set TR Dequeue commands may take some
time to execute and we may want to cancel more TDs during this time.
Currently this leads to Stop Endpoint completion handler calling this
function without testing for SET_DEQ_PENDING, which will trigger the
aforementioned problems when it happens.
On all endpoints, a halt condition causes Reset Endpoint to be queued
and an error status given to the class driver, which may unlink more
URBs in response. Stop Endpoint is queued and its handler may execute
concurrently with Set TR Dequeue queued by Reset Endpoint handler.
(Reset Endpoint handler calls this function too, but there seems to
be no possibility of it running concurrently with Set TR Dequeue).
Fix xhci_invalidate_cancelled_tds() to work correctly under a pending
Set TR Dequeue. Bail out of the function when SET_DEQ_PENDING is set,
then make the completion handler call the function again and also call
xhci_giveback_invalidated_tds(), which needs to be called next.
This seems to fix another potential bug, where the handler would call
xhci_invalidate_cancelled_tds(), which may clear some deferred TDs if
a sanity check fails, and the TDs wouldn't be given back promptly.
Said sanity check seems to be wrong and prone to false positives when
the endpoint halts, but fixing it is beyond the scope of this change,
besides ensuring that cleared TDs are given back properly.
Fixes: 5ceac4402f ("xhci: Handle TD clearing for multiple streams case")
CC: stable@vger.kernel.org
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-33-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some host controllers fail to atomically transition an endpoint to the
Running state on a doorbell ring and enter a hidden "Restarting" state,
which looks very much like Stopped, with the important difference that
it will spontaneously transition to Running anytime soon.
A Stop Endpoint command queued in the Restarting state typically fails
with Context State Error and the completion handler sees the Endpoint
Context State as either still Stopped or already Running. Even a case
of Halted was observed, when an error occurred right after the restart.
The Halted state is already recovered from by resetting the endpoint.
The Running state is handled by retrying Stop Endpoint.
The Stopped state was recognized as a problem on NEC controllers and
worked around also by retrying, because the endpoint soon restarts and
then stops for good. But there is a risk: the command may fail if the
endpoint is "stopped for good" already, and retries will fail forever.
The possibility of this was not realized at the time, but a number of
cases were discovered later and reproduced. Some proved difficult to
deal with, and it is outright impossible to predict if an endpoint may
fail to ever start at all due to a hardware bug. One such bug (albeit
on ASM3142, not on NEC) was found to be reliably triggered simply by
toggling an AX88179 NIC up/down in a tight loop for a few seconds.
An endless retries storm is quite nasty. Besides putting needless load
on the xHC and CPU, it causes URBs never to be given back, paralyzing
the device and connection/disconnection logic for the whole bus if the
device is unplugged. User processes waiting for URBs become unkillable,
drivers and kworker threads lock up and xhci_hcd cannot be reloaded.
For peace of mind, impose a timeout on Stop Endpoint retries in this
case. If they don't succeed in 100ms, consider the endpoint stopped
permanently for some reason and just give back the unlinked URBs. This
failure case is rare already and work is under way to make it rarer.
Start this work today by also handling one simple case of race with
Reset Endpoint, because it costs just two lines to implement.
Fixes: fd9d55d190 ("xhci: retry Stop Endpoint on buggy NEC controllers")
CC: stable@vger.kernel.org
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-32-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code which it is referencing does not exist in the same function,
or the file for that matter. Since it was added [1], the Interrupter
Moderation Interval can be changed within xhci addon, e.g. PCI
xhci_pci_setup().
[1], commit 0ebbab3742 ("USB: xhci: Ring allocation and initialization.")
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-31-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add xhci_dequeue_td() helper function to reduce code duplication.
Function xhci_dequeue_td() advances the dequeue pointer past the specified
Transfer Descriptor (TD) and releases the TD.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-30-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function is modified to return 'void' instead of an integer since it
invariably returns '0'. Additionally, multiple functions which only
return xhci_td_cleanup() are also refactored to return void.
This change eliminates the need for callers to handle a return value that
does not convey meaningful information and improve code readability, as it
becomes immediately clear that the function does not produce a significant
output.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-29-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function td_to_noop() does not utilize arguments 'xhci' and 'ep_ring'.
These unused arguments are removed to clean up the code.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-28-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove redundant TRB cycle reset, the TRB cycle is already set to zero by
the preceding memset(), making the explicit reset unnecessary.
Clarify ring loop start point. Change the loop start from the dequeue
segment to the start segment. Both approaches achieve the same result,
but starting from the start segment makes it clearer that the entire ring
is being zeroed out.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-27-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable 'max_interrupters' contains the maximum supported interrupters
or the maximum interrupters the user has requested. Thus, it should be
used instead of HCS_MAX_INTRS().
User set 'max_interrupters' value is validated in xhci_gen_setup(),
otherwise 'max_interrupters' value is 'HCS_MAX_INTRS(xhci->hcs_params1)'.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-26-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This quirk is old and seldom seen, as a result the trace is changed
to debug message and only printed when the quirk is set.
Move it into xhci_gen_setup() where the majority of quirks are set.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-25-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Old names:
* start_seg - last_trb_seg
* first_trb - last_trb
New names:
* start_seg - end_seg
* start_trb - end_trb
A Transfer Descriptor (TD) in the xhci driver is a data structure that
represents a single transaction to be performed by the USB host controller.
This transaction is defined by TRBs from 'start_trb' in 'start_seg' to
'end_trb' in 'end_seg'.
The terms "start" and "end" were chosen over "first" and "last" for ease
of searching within the codebase. The ring structure uses 'first_seg' and
'last_seg', while the TD structure uses 'start_seg' and 'end_seg'.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-24-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The definitions of vendor IDs follow the pattern PCI_VENDOR_ID_#vendor,
while device IDs — PCI_DEVICE_ID_#vendor_#device.
Update the ETRON device IDs to follow the above mentioned pattern.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-22-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit f8f80be501 ("xhci: Use soft retry to recover faster from
transaction errors"), unplugging USB device while enumeration results in
errors like this:
[ 364.855321] xhci_hcd 0000:0b:00.0: ERROR Transfer event for disabled endpoint slot 5 ep 2
[ 364.864622] xhci_hcd 0000:0b:00.0: @0000002167656d70 67f03000 00000021 0c000000 05038001
[ 374.934793] xhci_hcd 0000:0b:00.0: Abort failed to stop command ring: -110
[ 374.958793] xhci_hcd 0000:0b:00.0: xHCI host controller not responding, assume dead
[ 374.967590] xhci_hcd 0000:0b:00.0: HC died; cleaning up
[ 374.973984] xhci_hcd 0000:0b:00.0: Timeout while waiting for configure endpoint command
Seems that Etorn xHCI host can not perform Soft Retry correctly, apply
XHCI_NO_SOFT_RETRY quirk to disable Soft Retry and then issue is gone.
This patch depends on commit a4a251f8c2 ("usb: xhci: do not perform
Soft Retry for some xHCI hosts").
Fixes: f8f80be501 ("xhci: Use soft retry to recover faster from transaction errors")
Cc: stable@vger.kernel.org
Signed-off-by: Kuangyi Chiang <ki.chiang65@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-21-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Performing a stability stress test on a USB3.0 2.5G ethernet adapter
results in errors like this:
[ 91.441469] r8152 2-3:1.0 eth3: get_registers -71
[ 91.458659] r8152 2-3:1.0 eth3: get_registers -71
[ 91.475911] r8152 2-3:1.0 eth3: get_registers -71
[ 91.493203] r8152 2-3:1.0 eth3: get_registers -71
[ 91.510421] r8152 2-3:1.0 eth3: get_registers -71
The r8152 driver will periodically issue lots of control-IN requests
to access the status of ethernet adapter hardware registers during
the test.
This happens when the xHCI driver enqueue a control TD (which cross
over the Link TRB between two ring segments, as shown) in the endpoint
zero's transfer ring. Seems the Etron xHCI host can not perform this
TD correctly, causing the USB transfer error occurred, maybe the upper
driver retry that control-IN request can solve problem, but not all
drivers do this.
| |
-------
| TRB | Setup Stage
-------
| TRB | Link
-------
-------
| TRB | Data Stage
-------
| TRB | Status Stage
-------
| |
To work around this, the xHCI driver should enqueue a No Op TRB if
next available TRB is the Link TRB in the ring segment, this can
prevent the Setup and Data Stage TRB to be breaked by the Link TRB.
Check if the XHCI_ETRON_HOST quirk flag is set before invoking the
workaround in xhci_queue_ctrl_tx().
Fixes: d0e96f5a71 ("USB: xhci: Control transfer support.")
Cc: stable@vger.kernel.org
Signed-off-by: Kuangyi Chiang <ki.chiang65@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-20-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sometimes the hub driver does not recognize the USB device connected
to the external USB2.0 hub when the system resumes from S4.
After the SetPortFeature(PORT_RESET) request is completed, the hub
driver calls the HCD reset_device callback, which will issue a Reset
Device command and free all structures associated with endpoints
that were disabled.
This happens when the xHCI driver issue a Reset Device command to
inform the Etron xHCI host that the USB device associated with a
device slot has been reset. Seems that the Etron xHCI host can not
perform this command correctly, affecting the USB device.
To work around this, the xHCI driver should obtain a new device slot
with reference to commit 651aaf36a7 ("usb: xhci: Handle USB transaction
error on address command"), which is another way to inform the Etron
xHCI host that the USB device has been reset.
Add a new XHCI_ETRON_HOST quirk flag to invoke the workaround in
xhci_discover_or_reset_device().
Fixes: 2a8f82c4ce ("USB: xhci: Notify the xHC when a device is reset.")
Cc: stable@vger.kernel.org
Signed-off-by: Kuangyi Chiang <ki.chiang65@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-19-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Combine two if statements, because these hosts have the same
quirk flags applied.
[Mathias: has stable tag because other fixes in series depend on this]
Fixes: 91f7a1524a ("xhci: Apply broken streams quirk to Etron EJ188 xHCI host")
Cc: stable@vger.kernel.org
Signed-off-by: Kuangyi Chiang <ki.chiang65@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-18-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A ring consists of a list of segments, each containing a specific number of
TRBs. The xhci driver allocates and initializes ring segments and TRBs in
the same functions. This combined allocation and initialization process
leads to an issue where, after hibernation (S4 state), the xhci driver
frees all its memory and re-creates the rings, segments, and TRBs from
scratch.
Move all default ring segment initialization into function
xhci_initialize_ring_segments(). This function can be called to
reinitialize a ring without freeing and reallocating it.
Since xhci_alloc_segments_for_ring() no longer initializes segment TRBs,
xhci_initialize_ring_segments() is added to xhci_ring_expansion(). This
results in the last segment of the source ring having the 'LINK_TOGGLE'
bit set. Therefore, if the last source ring segment is not the last in
the destination ring, the 'LINK_TOGGLE' bit must be cleared.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-17-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare for splitting ring segments allocation and initialization by
reworking the xhci_link_segments() function. Segment linking and ring type
checks are moved out of xhci_link_segments(), and the function is renamed
to "xhci_set_link_trb()".
The goal is to keep ring linking within xhci_alloc_segments_for_ring() and
move initialization into a separate function.
Additionally, reorder and simplify xhci_set_link_trb() for better
readability.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-16-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor the xhci_link_rings() function to accept two rings: a source ring
and a destination ring. Previously, the function accepted a ring and a
segment list as arguments, now the function splices the source ring segment
list into the destination ring. This new approach reduces the number of
arguments and simplifies the code, making it easier to follow.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-15-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The segment list is only relevant within the context of the ring.
Thus, it is more logical to pass the ring itself when freeing all segments
from a ring, rather than passing the ring list.
Rename the function to "xhci_ring_segments_free" to align with the naming
convention of xhci_segment_free().
To make the freeing process more intuitive, free segments sequentially
from start to end (i.e., 0, 1, 2, 3, ...) instead of freeing the first
segment last (i.e., 1, 2, 3, ... 0).
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-14-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function xhci_alloc_segments_for_ring() currently takes 7 arguments,
5 of which are components of the 'xhci_ring' struct. Refactor the function
to accept a pointer to the 'xhci_ring' struct instead of passing these
components separately.
The change reduces the number of arguments, making the function signature
cleaner and easier to understand.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-13-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TRB cycle bit indicates TRB ownership by the Host Controller (HC) or
Host Controller Driver (HCD). New rings are initialized with 'cycle_state'
equal to one, and all its TRBs' cycle bits are set to zero. When handling
ring expansion, set the source ring cycle bits to the same value as the
destination ring.
Move the cycle bit setting from xhci_segment_alloc() to xhci_link_rings(),
and remove the 'cycle_state' argument from xhci_initialize_ring_info().
The xhci_segment_alloc() function uses kzalloc_node() to allocate segments,
ensuring that all TRB cycle bits are initialized to zero.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-12-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add macro to streamline and standardize the iteration over ring
segment list.
xhci_for_each_ring_seg(): Iterates over the entire ring segment list.
The xhci_free_segments_for_ring() function's while loop has not been
updated to use the new macro. This function has some underlying issues,
and as a result, it will be handled separately in a future patch.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-11-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ring data structure of each xHCI endpoint might stop sending
data due to the virt endpoint state.
Show the virt endpoint state within the endpoint context via debugfs
to facilitate debugging.
Co-developed-by: Xu Rao <raoxu@uniontech.com>
Signed-off-by: Xu Rao <raoxu@uniontech.com>
Signed-off-by: WangYuli <wangyuli@uniontech.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A successful 'Set TR Deq' command writes a new dequeue pointer to the
stream context for stream rings, show the content of the stream ctx
at command completion.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Show stream id, stream context type (SCT), ring dequeue pointer and
the DMA address of the stream context during stream allocation
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't trace ring pointers every time driver increases enqueue pointer
after queuing a TRB, or dequeue pointer after handling an event.
These xhci_inc_deq: and xhci_inc_enq: trace entries fill up the trace and
provides little useful info now that the TRB DMA address is printed with
the TRB itself.
Only trace ring during xhci_inc_enq() and xhci_inc_deq() in case we move
to a new ring segment.
Also don't show both segment and TRB addess in trace.
Segment is just TRB with 0xfff masked off.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DMA address of a queued TRB is essential when looking at traces as
both transfer events and command completion events refer to the command
or transfer based on its DMA address.
Previously the TRB address was figured out from xhci_inc_enq and
xhci_inc_deq trace entries seen after queuing or handlong a TRB.
Now that DMA address is shown in TRB tracing we can get rid of most of the
xhci_inc_enq and xhci_inc_deq traces thus decreasing trace size.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This function is supposed to sum the lengths of all transfer TRBs in
a TD up to a point, but it starts summing at the current dequeue since
it only ever gets called on the first pending TD.
This won't work when there are cancelled TDs at the beginning of the
ring. The function tries to exclude No-Ops from the count, but not all
cancelled TDs are No-Op'ed - not those the HW stopped on.
The absolutely obvious fix is to start counting at the TD's first TRB.
And remove the now-useless 'ring' parameter, and 'xhci' too.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function has two parameters which it doesn't use and hasn't ever
used. One caller even puts NULL there, knowing it will work anyway.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In addition to Normal TRB fields the Isoch TRBs have a SIA flag,
Frame ID, TLBPC and TBC fields.
Add these fields to tracing output
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241106101459.775897-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The is_bin_visible() callbacks should not modify the struct
bin_attribute passed as argument.
Enforce this by marking the argument as const.
As there are not many callback implementers perform this change
throughout the tree at once.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Ira Weiny <ira.weiny@intel.com>
Acked-by: Krzysztof Wilczyński <kw@linux.com>
Link: https://lore.kernel.org/r/20241103-sysfs-const-bin_attr-v2-5-71110628844c@weissschuh.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "*cmd" variable can be controlled by the user via debugfs. That means
"new_cam" can be as high as 255 while the size of the uc->updated[] array
is UCSI_MAX_ALTMODES (30).
The call tree is:
ucsi_cmd() // val comes from simple_attr_write_xsigned()
-> ucsi_send_command()
-> ucsi_send_command_common()
-> ucsi_run_command() // calls ucsi->ops->sync_control()
-> ucsi_ccg_sync_control()
Fixes: 170a6726d0 ("usb: typec: ucsi: add support for separate DP altmode devices")
Cc: stable <stable@kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/325102b3-eaa8-4918-a947-22aca1146586@stanley.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the device was already runtime suspended then during system suspend
we cannot access the device registers else it will crash.
Also we cannot access any registers after dwc3_core_exit() on some
platforms so move the dwc3_enable_susphy() call to the top.
Cc: stable@vger.kernel.org # v5.15+
Reported-by: William McVicker <willmcvicker@google.com>
Closes: https://lore.kernel.org/all/ZyVfcUuPq56R2m1Y@google.com
Fixes: 705e3ce37b ("usb: dwc3: core: Fix system suspend on TI AM62 platforms")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Tested-by: Will McVicker <willmcvicker@google.com>
Link: https://lore.kernel.org/r/20241104-am62-lpm-usb-fix-v1-1-e93df73a4f0d@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the read of USB_PDPHY_RX_ACKNOWLEDGE_REG failed, then hdr_len and
txbuf_len are uninitialized. This commit stops to print uninitialized
value and misleading/false data.
Cc: stable@vger.kernel.org
Fixes: a4422ff221 (" usb: typec: qcom: Add Qualcomm PMIC Type-C driver")
Signed-off-by: Rex Nie <rex.nie@jaguarmicro.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20241030133632.2116-1-rex.nie@jaguarmicro.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 6ed05c68cb ("usb: musb: sunxi: Explicitly release USB PHY on
exit") will cause that usb phy @glue->xceiv is accessed after released.
1) register platform driver @sunxi_musb_driver
// get the usb phy @glue->xceiv
sunxi_musb_probe() -> devm_usb_get_phy().
2) register and unregister platform driver @musb_driver
musb_probe() -> sunxi_musb_init()
use the phy here
//the phy is released here
musb_remove() -> sunxi_musb_exit() -> devm_usb_put_phy()
3) register @musb_driver again
musb_probe() -> sunxi_musb_init()
use the phy here but the phy has been released at 2).
...
Fixed by reverting the commit, namely, removing devm_usb_put_phy()
from sunxi_musb_exit().
Fixes: 6ed05c68cb ("usb: musb: sunxi: Explicitly release USB PHY on exit")
Cc: stable@vger.kernel.org
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20241029-sunxi_fix-v1-1-9431ed2ab826@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The use of (of|device)_property_read_bool() for non-boolean properties
is deprecated in favor of of_property_present() when testing for
property presence.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Acked-by: Peter Chen <peter.chen@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20241104190820.277702-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the USB fixes in here as well, and this resolves a merge
conflict in:
drivers/usb/typec/tcpm/tcpm.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/20241101150730.090dc30f@canb.auug.org.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit fde192511b ("kconfig: remove tristate choice support"),
all choice blocks are now boolean. There is no longer a need to specify
the choice type explicitly.
Most choice blocks already use "prompt". Before the next commit removes
support for the "bool" syntax in choice entries, this commit converts
the remaining "bool" occurences under drivers/usb/.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
The TUSB1046-DCI is a USB-C linear redriver crosspoint switch, which can
mux SuperSpeed lanes from a Type-C connector to a USB3.0 data lane or up to
4 display port lanes.
Add support for driving the TUSB1046 as a Type-C orientation switch and
DisplayPort altmode multiplexer.
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241024-tusb1046-v2-2-d031b1a43e6d@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some PCIe-to-USB controllers such as TI's TUSB73x0 3.0 xHCI host
controller supports controlling the PWRONx polarity via the USB control
register (E0h). Add support for device tree property
ti,pwron-active-high which indicates PWRONx to be active high and
configure the E0h register accordingly. This enables the software
control for the TUSB73x0's PWRONx outputs with an inverted polarity from
the default configuration which could be used as USB EN signals for the
other hubs or devices.
Signed-off-by: Parth Pancholi <parth.pancholi@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20241029072444.8827-3-francesco@dolcini.it
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_gpio.h is deprecated and subject to remove. The drivers in question
don't use it, simply remove the unused header.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20241031103818.2451816-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "dev_dbg(&urb->dev->dev, ..." which happens after usb_free_urb(urb)
is a use after free of the "urb" pointer. Store the "dev" pointer at the
start of the function to avoid this issue.
Fixes: 984f686832 ("USB: serial: io_edgeport.c: remove dbg() usage")
Cc: stable@vger.kernel.org
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
PD3.1 spec ("8.3.3.3.3 PE_SNK_Wait_for_Capabilities State") mandates
that the policy engine perform a hard reset when SinkWaitCapTimer
expires. Instead the code explicitly does a GET_SOURCE_CAP when the
timer expires as part of SNK_WAIT_CAPABILITIES_TIMEOUT. Due to this the
following compliance test failures are reported by the compliance tester
(added excerpts from the PD Test Spec):
* COMMON.PROC.PD.2#1:
The Tester receives a Get_Source_Cap Message from the UUT. This
message is valid except the following conditions: [COMMON.PROC.PD.2#1]
a. The check fails if the UUT sends this message before the Tester
has established an Explicit Contract
...
* TEST.PD.PROT.SNK.4:
...
4. The check fails if the UUT does not send a Hard Reset between
tTypeCSinkWaitCap min and max. [TEST.PD.PROT.SNK.4#1] The delay is
between the VBUS present vSafe5V min and the time of the first bit
of Preamble of the Hard Reset sent by the UUT.
For the purpose of interoperability, restrict the quirk introduced in
https://lore.kernel.org/all/20240523171806.223727-1-sebastian.reichel@collabora.com/
to only non self-powered devices as battery powered devices will not
have the issue mentioned in that commit.
Cc: stable@vger.kernel.org
Fixes: 122968f8dd ("usb: typec: tcpm: avoid resets for missing source capability messages")
Reported-by: Badhri Jagan Sridharan <badhri@google.com>
Closes: https://lore.kernel.org/all/CAPTae5LAwsVugb0dxuKLHFqncjeZeJ785nkY4Jfd+M-tCjHSnQ@mail.gmail.com/
Signed-off-by: Amit Sunil Dhamne <amitsd@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20241024022233.3276995-1-amitsd@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For devm_usb_put_phy(), its comment says it needs to invoke usb_put_phy()
to release the phy, but it does not do that actually, so it can not fully
undo what the API devm_usb_get_phy() does, that is wrong, fixed by using
devres_release() instead of devres_destroy() within the API.
Fixes: cedf860237 ("usb: phy: move bulk of otg/otg.c to phy/phy.c")
Cc: stable@vger.kernel.org
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20241020-usb_phy_fix-v1-1-7f79243b8e1e@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Follow the advice in Documentation/filesystems/sysfs.rst:
show() should only use sysfs_emit() or sysfs_emit_at() when formatting
the value to be returned to user space.
Signed-off-by: Jiayi Li <lijiayi@kylinos.cn>
Link: https://lore.kernel.org/r/20241023085429.2865488-1-lijiayi@kylinos.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for DT time properties to allow users to define platform
specific timing deadlines of certain timers rather than using hardcoded
ones. For values that have not been explicitly defined in DT using this
property, default values will be set therefore, making this change
backward compatible.
Signed-off-by: Amit Sunil Dhamne <amitsd@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241022-pd-dt-time-props-v1-2-fea96f51b302@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current logic is rigid, setting num_fifos to fixed values.
3 for any maxburst greater than 1.
tx_fifo_resize_max_num for maxburst greater than 6.
Additionally, it did not differentiate much between bulk and
isochronous transfers, applying similar logic to both.
The updated logic is more flexible and specifically designed to meet
the unique requirements of both bulk and isochronous transfers. We
have made every effort to satisfy all needs and requirements, verified
on our specific platform and application.
Bulk Transfers: Ensures that num_fifos is optimized by considering both
the maxburst and DT property "tx-fifo-max-num" for super speed and
above. For high-speed and below bulk endpoints, a 2K TxFIFO allocation
is used to meet efficient data transfer needs, considering
FIFO-constrained platforms.
Isochronous Transfers: Ensures that num_fifos is sufficient by
considering the maximum packet multiplier for HS and below and maxburst
for Super-speed and above eps, along with a constraint with the DT
property "tx-fifo-max-num".
This change aims to optimize the allocation of Tx FIFOs for both bulk
and isochronous endpoints, potentially improving data transfer efficiency
and overall performance. It also enhances support for all use cases,
which can be tweaked with DT parameters and the endpoint’s maxburst and
maxpacket. This structured approach ensures that the appropriate number
of FIFOs is allocated based on the endpoint type and USB speed.
Signed-off-by: Akash Kumar <quic_akakum@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20241017064423.7056-1-quic_akakum@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
That command is executed from several locations in the
driver, so providing a dedicated helper function for it.
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241017091112.1178509-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the __free() macro for 'altmodes_node' to automatically release the
node when it goes out of scope, removing the need for explicit calls to
fwnode_handle_put().
Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241021-typec-class-fwnode_handle_put-v2-2-3281225d3d27@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'altmodes_node' fwnode_handle is never released after it is no
longer required, which leaks the resource.
Add the required call to fwnode_handle_put() when 'altmodes_node' is no
longer required.
Cc: stable@vger.kernel.org
Fixes: 7b458a4c5d ("usb: typec: Add typec_port_register_altmodes()")
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://lore.kernel.org/r/20241021-typec-class-fwnode_handle_put-v2-1-3281225d3d27@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If drm_dp_hpd_bridge_register() fails, the probe function returns
without removing the fwnode via fwnode_handle_put(), leaking the
resource.
Jump to fwnode_remove if drm_dp_hpd_bridge_register() fails to remove
the fwnode acquired with device_get_named_child_node().
Cc: stable@vger.kernel.org
Fixes: 7d9f1b72b2 ("usb: typec: qcom-pmic-typec: switch to DRM_AUX_HPD_BRIDGE")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241020-qcom_pmic_typec-fwnode_remove-v2-2-7054f3d2e215@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The right function to release a fwnode acquired via
device_get_named_child_node() is fwnode_handle_put(), and not
fwnode_remove_software_node(), as no software node is being handled.
Replace the calls to fwnode_remove_software_node() with
fwnode_handle_put() in qcom_pmic_typec_probe() and
qcom_pmic_typec_remove().
Cc: stable@vger.kernel.org
Fixes: a4422ff221 ("usb: typec: qcom: Add Qualcomm PMIC Type-C driver")
Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241020-qcom_pmic_typec-fwnode_remove-v2-1-7054f3d2e215@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a boot hang issue triggered when a USB3 device is incorrectly assumed
to be tunneled over USB4, thus attempting to create a device link between
the USB3 "consumer" device and the USB4 "supplier" Host Interface before
the USB4 side is properly bound to a driver.
This could happen if xhci isn't capable of detecting tunneled devices,
but ACPI tables contain all info needed to assume device is tunneled.
i.e. udev->tunnel_mode == USB_LINK_UNKNOWN.
It turns out that even for actual tunneled USB3 devices it can't be
assumed that the thunderbolt driver providing the tunnel is loaded
before the tunneled USB3 device is created.
The tunnel can be created by BIOS and remain in use by thunderbolt/USB4
host driver once it loads.
Solve this by making the device link "stateless", which doesn't create
a driver presence order dependency between the supplier and consumer
drivers.
It still guarantees correct suspend/resume and shutdown ordering.
cc: Mario Limonciello <mario.limonciello@amd.com>
Fixes: f1bfb4a6fe ("usb: acpi: add device link between tunneled USB3 device and USB4 Host Interface")
Tested-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20241024131355.3836538-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit d483f034f0 ("usb: dwc2: Skip clock gating on Broadcom SoCs")
introduced a regression on Raspberry Pi 3 B Plus, which prevents
enumeration of the onboard Microchip LAN7800 in case no external USB device
is connected during boot.
Fixes: d483f034f0 ("usb: dwc2: Skip clock gating on Broadcom SoCs")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20241025103621.4780-2-wahrenst@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During the aborting of a command, the software receives a command
completion event for the command ring stopped, with the TRB pointing
to the next TRB after the aborted command.
If the command we abort is located just before the Link TRB in the
command ring, then during the 'command ring stopped' completion event,
the xHC gives the Link TRB in the event's cmd DMA, which causes a
mismatch in handling command completion event.
To address this situation, move the 'command ring stopped' completion
event check slightly earlier, since the specific command it stopped
on isn't of significant concern.
Fixes: 7f84eef0da ("USB: xhci: No-op command queueing and irq handler.")
Cc: stable@vger.kernel.org
Signed-off-by: Faisal Hassan <quic_faisalh@quicinc.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241022155631.1185-1-quic_faisalh@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use pm_runtime_put in the remove function and pm_runtime_get to disable
RPM on platforms that don't support runtime D3, as re-enabling it through
sysfs auto power control may cause the controller to malfunction. This
can lead to issues such as hotplug devices not being detected due to
failed interrupt generation.
Fixes: a5d6264b63 ("xhci: Enable RPM on controllers that support low-power states")
Cc: stable <stable@kernel.org>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20241024133718.723846-1-Basavaraj.Natikar@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some new modem device ids.
Everything has been in linux-next over night with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCZxIyrQAKCRALxc3C7H1l
CCgGAQDkVANkAOTEq8zOfpaULkWkMJXMRzd28YrkCqlgJfbkYQEAjTWtz8F48Ne7
V9CYj/dbNULlQ0Q+kqKqGBcKdZrq2AI=
=/sNu
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-6.12-rc4' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial device ids for 6.12-rc4
Here are some new modem device ids.
Everything has been in linux-next over night with no reported issues.
* tag 'usb-serial-6.12-rc4' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Telit FN920C04 MBIM compositions
USB: serial: option: add support for Quectel EG916Q-GL
Treat each completed full size write to /dev/ttyDBC0 as a separate usb
transfer. Make sure the size of the TRBs matches the size of the tty
write by first queuing as many max packet size TRBs as possible up to
the last TRB which will be cut short to match the size of the tty write.
This solves an issue where userspace writes several transfers back to
back via /dev/ttyDBC0 into a kfifo before dbgtty can find available
request to turn that kfifo data into TRBs on the transfer ring.
The boundary between transfer was lost as xhci-dbgtty then turned
everyting in the kfifo into as many 'max packet size' TRBs as possible.
DbC would then send more data to the host than intended for that
transfer, causing host to issue a babble error.
Refuse to write more data to kfifo until previous tty write data is
turned into properly sized TRBs with data size boundaries matching tty
write size
Tested-by: Uday M Bhat <uday.m.bhat@intel.com>
Tested-by: Łukasz Bartosik <ukaszb@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241016140000.783905-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
