Correct handling of devices with sector_size other that 512 bytes.
In the case of a 4Kn device sector_size it is possible to describe a much
larger DSM Trim than the current fixed default of 512 bytes.
This patch assumes the minimum descriptor is sector_size and fills out
the descriptor accordingly.
The ACS-2 specification is quite clear that the DSM command payload is
sized as number of 512 byte transfers so a 4Kn device will operate
correctly without this patch.
Signed-off-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Acked-by: Tejun Heo <tj@kernel.org>
SATA drives may support write same via SCT. This is useful
for setting the drive contents to a specific pattern (0's).
Translate a SCSI WRITE SAME 16 command to be either a DSM TRIM
command or an SCT Write Same command.
Based on the UNMAP flag:
- When set translate to DSM TRIM
- When not set translate to SCT Write Same
Signed-off-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Tejun Heo <tj@kernel.org>
Safely overwriting the attached page to ATA format from the SCSI formatted
variant.
Signed-off-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Tejun Heo <tj@kernel.org>
Despite ST AHCI version = 1.3, reading HOST_PORTS_IMPL
returns 0. So force_port_map to 1 by using ports-implemented
DT property.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
By default the SATA IP on the qoriq SoCs does not generating
coherent/snoopable transactions. This patch enable it in the
sata axicc register.
In addition, the dma-coherent property must be set on the
SATA controller nodes.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The default values for Port Phy2Cfg register and
Port Phy3Cfg register are better, no need to overwrite them.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
scsi_done() was called repeatedly and apparently because of that,
the kernel would call trace when we touch the Control mode page:
Call Trace:
[<ffffffff812ea0d2>] dump_stack+0x63/0x81
[<ffffffff81079cfb>] __warn+0xcb/0xf0
[<ffffffff81079e2d>] warn_slowpath_null+0x1d/0x20
[<ffffffffa00f51b0>] ata_eh_finish+0xe0/0xf0 [libata]
[<ffffffffa00fb830>] sata_pmp_error_handler+0x640/0xa50 [libata]
[<ffffffffa00470ed>] ahci_error_handler+0x1d/0x70 [libahci]
[<ffffffffa00f55f0>] ata_scsi_port_error_handler+0x430/0x770 [libata]
[<ffffffffa00eff8d>] ? ata_scsi_cmd_error_handler+0xdd/0x160 [libata]
[<ffffffffa00f59d7>] ata_scsi_error+0xa7/0xf0 [libata]
[<ffffffffa00913ba>] scsi_error_handler+0xaa/0x560 [scsi_mod]
[<ffffffffa0091310>] ? scsi_eh_get_sense+0x180/0x180 [scsi_mod]
[<ffffffff81098eb8>] kthread+0xd8/0xf0
[<ffffffff815d913f>] ret_from_fork+0x1f/0x40
[<ffffffff81098de0>] ? kthread_worker_fn+0x170/0x170
---[ end trace 8b7501047e928a17 ]---
Removed the unnecessary code and let ata_scsi_translate() do the job.
Also, since ata_mselect_control() has no ATA command to send to the
device, ata_scsi_mode_select_xlat() should return 1 for it, so that
ata_scsi_translate() will finish early to avoid ata_qc_issue().
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
ata_mselect_*() would initialize a char array for storing a copy of
the current mode page. However, char could be signed char. In that
case, bytes larger than 127 would be converted to negative number.
For example, 0xff from def_control_mpage[] would become -1. This
prevented ata_mselect_control() from working at all, since when it
did the read-only bits check, there would always be a mismatch.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
- LED driver for TI LP3952 6-Channel Color LED
LED core improvements:
- Only descend into leds directory when CONFIG_NEW_LEDS is set
- Add no-op gpio_led_register_device when LED subsystem is disabled
- MAINTAINERS: Add file patterns for led device tree bindings
LED Trigger core improvements:
- return error if invalid trigger name is provided via sysfs
LED class drivers improvements
- is31fl32xx: define complete i2c_device_id table
- is31fl32xx: fix typo in id and match table names
- leds-gpio: Set of_node for created LED devices
- pca9532: Add device tree support
Conversion of IDE trigger to common disk trigger:
- leds: convert IDE trigger to common disk trigger
- leds: documentation: 'ide-disk' to 'disk-activity'
- unicore32: use the new LED disk activity trigger
- parisc: use the new LED disk activity trigger
- mips: use the new LED disk activity trigger
- arm: use the new LED disk activity trigger
- powerpc: use the new LED disk activity trigger
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.17 (GNU/Linux)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=8lmX
-----END PGP SIGNATURE-----
Merge tag 'leds_for_4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
"New LED class driver:
- LED driver for TI LP3952 6-Channel Color LED
LED core improvements:
- Only descend into leds directory when CONFIG_NEW_LEDS is set
- Add no-op gpio_led_register_device when LED subsystem is disabled
- MAINTAINERS: Add file patterns for led device tree bindings
LED Trigger core improvements:
- return error if invalid trigger name is provided via sysfs
LED class drivers improvements
- is31fl32xx: define complete i2c_device_id table
- is31fl32xx: fix typo in id and match table names
- leds-gpio: Set of_node for created LED devices
- pca9532: Add device tree support
Conversion of IDE trigger to common disk trigger:
- leds: convert IDE trigger to common disk trigger
- leds: documentation: 'ide-disk' to 'disk-activity'
- unicore32: use the new LED disk activity trigger
- parisc: use the new LED disk activity trigger
- mips: use the new LED disk activity trigger
- arm: use the new LED disk activity trigger
- powerpc: use the new LED disk activity trigger"
* tag 'leds_for_4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
leds: is31fl32xx: define complete i2c_device_id table
leds: is31fl32xx: fix typo in id and match table names
leds: LED driver for TI LP3952 6-Channel Color LED
leds: leds-gpio: Set of_node for created LED devices
leds: triggers: return error if invalid trigger name is provided via sysfs
leds: Only descend into leds directory when CONFIG_NEW_LEDS is set
leds: Add no-op gpio_led_register_device when LED subsystem is disabled
unicore32: use the new LED disk activity trigger
parisc: use the new LED disk activity trigger
mips: use the new LED disk activity trigger
arm: use the new LED disk activity trigger
powerpc: use the new LED disk activity trigger
leds: documentation: 'ide-disk' to 'disk-activity'
leds: convert IDE trigger to common disk trigger
leds: pca9532: Add device tree support
MAINTAINERS: Add file patterns for led device tree bindings
Pull core block updates from Jens Axboe:
- the big change is the cleanup from Mike Christie, cleaning up our
uses of command types and modified flags. This is what will throw
some merge conflicts
- regression fix for the above for btrfs, from Vincent
- following up to the above, better packing of struct request from
Christoph
- a 2038 fix for blktrace from Arnd
- a few trivial/spelling fixes from Bart Van Assche
- a front merge check fix from Damien, which could cause issues on
SMR drives
- Atari partition fix from Gabriel
- convert cfq to highres timers, since jiffies isn't granular enough
for some devices these days. From Jan and Jeff
- CFQ priority boost fix idle classes, from me
- cleanup series from Ming, improving our bio/bvec iteration
- a direct issue fix for blk-mq from Omar
- fix for plug merging not involving the IO scheduler, like we do for
other types of merges. From Tahsin
- expose DAX type internally and through sysfs. From Toshi and Yigal
* 'for-4.8/core' of git://git.kernel.dk/linux-block: (76 commits)
block: Fix front merge check
block: do not merge requests without consulting with io scheduler
block: Fix spelling in a source code comment
block: expose QUEUE_FLAG_DAX in sysfs
block: add QUEUE_FLAG_DAX for devices to advertise their DAX support
Btrfs: fix comparison in __btrfs_map_block()
block: atari: Return early for unsupported sector size
Doc: block: Fix a typo in queue-sysfs.txt
cfq-iosched: Charge at least 1 jiffie instead of 1 ns
cfq-iosched: Fix regression in bonnie++ rewrite performance
cfq-iosched: Convert slice_resid from u64 to s64
block: Convert fifo_time from ulong to u64
blktrace: avoid using timespec
block/blk-cgroup.c: Declare local symbols static
block/bio-integrity.c: Add #include "blk.h"
block/partition-generic.c: Remove a set-but-not-used variable
block: bio: kill BIO_MAX_SIZE
cfq-iosched: temporarily boost queue priority for idle classes
block: drbd: avoid to use BIO_MAX_SIZE
block: bio: remove BIO_MAX_SECTORS
...
Pull libata updates from Tejun Heo:
"libata saw quite a bit of activities in this cycle:
- SMR drive support still being worked on
- bug fixes and improvements to misc SCSI command emulation
- some low level driver updates"
* 'for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (39 commits)
libata-scsi: better style in ata_msense_*()
AHCI: Clear GHC.IS to prevent unexpectly asserting INTx
ata: sata_dwc_460ex: remove redundant dev_err call
ata: define ATA_PROT_* in terms of ATA_PROT_FLAG_*
libata: remove ATA_PROT_FLAG_DATA
libata: remove ata_is_nodata
ata: make lba_{28,48}_ok() use ATA_MAX_SECTORS{,_LBA48}
libata-scsi: minor cleanup for ata_scsi_zbc_out_xlat
libata-scsi: Fix ZBC management out command translation
libata-scsi: Fix translation of REPORT ZONES command
ata: Handle ATA NCQ NO-DATA commands correctly
libata-eh: decode all taskfile protocols
ata: fixup ATA_PROT_NODATA
libsas: use ata_is_ncq() and ata_has_dma() accessors
libata: use ata_is_ncq() accessors
libata: return boolean values from ata_is_*
libata-scsi: avoid repeated calculation of number of TRIM ranges
libata-scsi: reject WRITE SAME (16) with n_block that exceeds limit
libata-scsi: rename ata_msense_ctl_mode() to ata_msense_control()
libata-scsi: fix D_SENSE bit relection in control mode page
...
Pull libata fix from Tejun Heo:
"Another fallout from max_sectors bump a couple years ago. The lite-on
optical drive times out on large requests"
* 'for-4.7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: LITE-ON CX1-JB256-HP needs lower max_sectors
`changeable` is the "version" of mode page requested by the user.
It will be less confusing/misleading if we do not check it
"together" with the setting bits of the drive.
Not to mention that we currently have ata_mselect_*() implemented
in a way that each of them will serve exclusively a particular bit
on each page. The old style will hence make the condition look even
more unnecessarily arcane if the ata_msense_*() is reflecting more
than one bit.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Due to PCI subsystem behaviour, unloading AHCI driver will disable
MSI and enable INTx. When HBA supports MSIx or Multiple MSI, Driver's
irq handler doesn't clear GHC.IS register. It works well when reading or
writing data and GHC.IS is always non-zero. But when unloading driver
(or any other operation which causes disable MSIx and enable INTx), PCI
subsystem uses config write(Rx04.bit10) to enable INTx. Because
GHC.IS is non-zero, HBA will falsely assume some port needs interrupt
service. Then it asserts INTx. To make things worse, when AHCI controller
shares the same interrupt pin with other PCI device, that PCI device's ISR
will be called and nobody de-asserts previous INTx.
This patch clears GHC.IS in ahci_port_stop() even when using MSIx or
MMSI to prevent this case. It ensures GHC.IS is zero before PCI subsystem
enables INTx.
tj: Minor updates to the comment.
Signed-off-by: Raymond Pang <raymond_rule@hotmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Tejun Heo <tj@kernel.org>
This avoid the need to always translate between the two in ata_prot_flags
and generally cleans up the taskfile protocol usage.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
The reset_all variable name is misleading as this bit is also applicable to
open, close, and finish actions. So rename that variable to "all" and remove
the unnecessary mask operation that's already done earlier.
Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com>
[hch: split from the previous patch]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
The subcommand for NCQ NON-DATA must be specified in the feature
(low byte), not the high-order count byte. Also make sure to properly
cast the all bit to a u16 before shiting it by 8 to avoid undefined
behavior.
Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com>
[hch: split the original patch into two, updated changelog]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Include reporting options when translating REPORT ZONES commmand to
ATA NCQ, and make sure we only look at the actually specified bits
in the CDB for the options.
Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com>
[hch: update patch description]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add a new taskfile protocol ATA_PROT_NCQ_NODATA to handle
ATA NCQ NO-DATA commands correctly.
And fixup ata_scsi_zbc_out_xlat() to use it.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Some taskfile protocol values where missing in ata_eh_link_report().
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
The taskfile protocol is a numeric value, and can not be ORed. Currently
this is harmless as the protocol is always zeroed before, but if it ever
has a non-zero value the ORing would create incorrect results.
Signed-off-by: Hannes Reinecke <hare@suse.de>
[hch: updated patch description]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Use accessor functions instead of the raw value.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Currently libata statically allows only 1-block (512-byte) payload
for each TRIM command. Each payload can carry 64 TRIM ranges since
each range requires 8 bytes.
It is silly to keep doing the calculation (512 / 8) in different
places. Hence, define the new ATA_MAX_TRIM_RNUM for the result.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Currently if a WRITE SAME (16) command is issued to the SATL with
"number of blocks" that is larger than the "Maximum write same length"
(which is the maximum number of blocks per TRIM command allowed in
libata, currently 65535 * 512 / 8 blocks), the SATL will accept the
command and translate it to a TRIM command with the upper limit.
However, according to SBC (as of sbc4r11.pdf), the "device server"
should terminate the command with "Invalid field in CDB" in that case.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
To make it consistent with the recently added ata_mselect_control().
We probably shouldn't have the word "mode" in its name anyway, since
that's not the case for other ata_msense_*() / ata_mselect_*() either.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The bit should always be set to 1 when the requested version of
page is "changeable" because we've made it so in ata_mselect_control().
Also, it should always be set to 1 if ATA_DFLAG_D_SENSE is set (when
the requested version of page is "current" or "default").
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
According to the HPT366 data sheet, PCI config space dword 0x40-0x43
bits 11:8 specify the primary drive cmd_high_time, however,
currently just 3 bits of the 4 are being used because the mask
is 0x700 and not 0x0f00. Fix the mask, allowing for the 40MHz clock
to be detected.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The comment suggests we should be having an SPC-3 version descriptor
but the 0260h is the code for "SPC-2 (no version claimed)". Correct
it to 0300h so that it has the "SPC-3 (no version claimed)" descriptor.
Note that we are claiming SPC-3 version compatibility in the VERSION
field of the standard INQUIRY data. Therefore, I assume the typo was
on the code but not on the comment.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Avoid performance bottleneck when being SCSI pass-through'd to
virtual machines with other OSes (e.g. Windows) via virtio-scsi
and scsi-block in qemu.
Ref.: https://github.com/YanVugenfirer/kvm-guest-drivers-windows/issues/63
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Without this fix, the DRA bit of the caching mode page would not
be updated when the read look-ahead feature is toggled (e.g. with
`smartctl --set`), but will only be until, for example, the write
cache feature is touched.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Commit 856c46639309 ("libata: support device-managed ZAC devices")
had the line that "bumps" the VERSION field in standard INQUIRY data
removed. Add it back and claim SPC-5 version compatibility, which
matches with the current version descriptor "SPC-5 (no version claimed)"
that is used for ZAC devices.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
It does not make sense and is confusing to respond with "Invalid
field in CDB" while we have no support at all implemented for
FORMAT UNIT. It is decent to let it go to the default, which
will respond with "Invalid command operation code" instead.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata fixes from Tejun Heo:
"Two trivial fixes - one for a bug in the allocation failure path and
the other a compiler warning fix"
* 'for-4.7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ata: sata_mv: fix mis-conversion in mv_write_cached_reg()
ata: fix return value check in ahci_seattle_get_port_info()
Note that `&acdev->host->lock' and `qc->ap->lock' denote the same lock, and it's
particularly confusing to spin_lock on the former but spin_unlock on the latter.
Signed-off-by: Iago Abal <mail@iagoabal.eu>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch converts the IDE specific LED trigger to a generic disk
activity LED trigger. The libata core is now a trigger source just
like before the IDE disk driver. It's merely a replacement of the
string ide by disk.
The patch is taken from http://dev.gentoo.org/~josejx/ata.patch and is
widely used by any ibook/powerbook owners with great satisfaction.
Likewise, it is very often used successfully on different ARM platforms.
Unlike the original patch, the existing 'ide-disk' trigger is still
available for backward compatibility. That reduce the amount of patches
in affected device trees out of the mainline kernel. For further
development, the new name 'disk-activity' should be used.
Cc: Joseph Jezak <josejx@gentoo.org>
Cc: Jörg Sommer <joerg@alea.gnuu.de>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Stephan Linz <linz@li-pro.net>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Fix the signed issue in mv_write_cached_reg() where the laddr
is assigned from a (long)addr instead of (unsigned long)addr.
Fixes the following warnings:
drivers/ata/sata_mv.c:989:26: warning: cast removes address space of expression
drivers/ata/sata_mv.c:989:26: warning: cast removes address space of expression
drivers/ata/sata_mv.c:989:26: warning: cast removes address space of expression
drivers/ata/sata_mv.c:989:26: warning: cast removes address space of expression
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Tejun Heo <tj@kernel.org>
The sysfs file for the libata error handling has multiple issues
in the way it prints time stamps:
* it prints a 9-digit nanosecond value using a %06lu format string,
which drops some leading zeroes
* it converts a 64-bit jiffes value to a timespec using
jiffies_to_timespec(), which takes a 'long' argument, so the
result is wrong after a jiffies overflow (49 days).
* we try to avoid using timespec because that generally overflows
in 2038, although this particular usage is ok.
This replaces the jiffies_to_timespec call with an open-coded
implementation that gets it right.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
In case of error, the function devm_kzalloc() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should
be replaced with NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
sas_ata_strategy_handler() adds the works of the ata error handler to
system_unbound_wq. This workqueue asynchronously runs work items, so the
ata error handler will be performed concurrently on different CPUs. In
this case, ->host_failed will be decreased simultaneously in
scsi_eh_finish_cmd() on different CPUs, and become abnormal.
It will lead to permanently inequality between ->host_failed and
->host_busy, and scsi error handler thread won't start running. IO
errors after that won't be handled.
Since all scmds must have been handled in the strategy handler, just
remove the decrement in scsi_eh_finish_cmd() and zero ->host_busy after
the strategy handler to fix this race.
Fixes: 50824d6c5657 ("[SCSI] libsas: async ata-eh")
Cc: stable@vger.kernel.org
Signed-off-by: Wei Fang <fangwei1@huawei.com>
Reviewed-by: James Bottomley <jejb@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We currently set REQ_WRITE/WRITE for all non READ IOs
like discard, flush, writesame, etc. In the next patches where we
no longer set up the op as a bitmap, we will not be able to
detect a operation direction like writesame by testing if REQ_WRITE is
set.
This patch converts the drivers and cgroup to use the
op_is_write helper. This should just cover the simple
cases. I did dm, md and bcache in their own patches
because they were more involved.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Most users of IS_ERR_VALUE() in the kernel are wrong, as they
pass an 'int' into a function that takes an 'unsigned long'
argument. This happens to work because the type is sign-extended
on 64-bit architectures before it gets converted into an
unsigned type.
However, anything that passes an 'unsigned short' or 'unsigned int'
argument into IS_ERR_VALUE() is guaranteed to be broken, as are
8-bit integers and types that are wider than 'unsigned long'.
Andrzej Hajda has already fixed a lot of the worst abusers that
were causing actual bugs, but it would be nice to prevent any
users that are not passing 'unsigned long' arguments.
This patch changes all users of IS_ERR_VALUE() that I could find
on 32-bit ARM randconfig builds and x86 allmodconfig. For the
moment, this doesn't change the definition of IS_ERR_VALUE()
because there are probably still architecture specific users
elsewhere.
Almost all the warnings I got are for files that are better off
using 'if (err)' or 'if (err < 0)'.
The only legitimate user I could find that we get a warning for
is the (32-bit only) freescale fman driver, so I did not remove
the IS_ERR_VALUE() there but changed the type to 'unsigned long'.
For 9pfs, I just worked around one user whose calling conventions
are so obscure that I did not dare change the behavior.
I was using this definition for testing:
#define IS_ERR_VALUE(x) ((unsigned long*)NULL == (typeof (x)*)NULL && \
unlikely((unsigned long long)(x) >= (unsigned long long)(typeof(x))-MAX_ERRNO))
which ends up making all 16-bit or wider types work correctly with
the most plausible interpretation of what IS_ERR_VALUE() was supposed
to return according to its users, but also causes a compile-time
warning for any users that do not pass an 'unsigned long' argument.
I suggested this approach earlier this year, but back then we ended
up deciding to just fix the users that are obviously broken. After
the initial warning that caused me to get involved in the discussion
(fs/gfs2/dir.c) showed up again in the mainline kernel, Linus
asked me to send the whole thing again.
[ Updated the 9p parts as per Al Viro - Linus ]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: https://lkml.org/lkml/2016/1/7/363
Link: https://lkml.org/lkml/2016/5/27/486
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> # For nvmem part
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
