* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (278 commits)
arm: remove machine_desc.io_pg_offst and .phys_io
arm: use addruart macro to establish debug mappings
arm: return both physical and virtual addresses from addruart
arm/debug: consolidate addruart macros for CONFIG_DEBUG_ICEDCC
ARM: make struct machine_desc definition coherent with its comment
eukrea_mbimxsd-baseboard: Pass the correct GPIO to gpio_free
cpuimx27: fix compile when ULPI is selected
mach-pcm037_eet: fix compile errors
Fixing ethernet driver compilation error for i.MX31 ADS board
cpuimx51: update board support
mx5: add cpuimx51sd module and its baseboard
iomux-mx51: fix GPIO_1_xx 's IOMUX configuration
imx-esdhc: update devices registration
mx51: add resources for SD/MMC on i.MX51
iomux-mx51: fix SD1 and SD2's iomux configuration
clock-mx51: rename CLOCK1 to CLOCK_CCGR for better readability
clock-mx51: factorize clk_set_parent and clk_get_rate
eukrea_mbimxsd: add support for DVI displays
cpuimx25 & cpuimx35: fix OTG port registration in host mode
i.MX31 and i.MX35 : fix errate TLSbo65953 and ENGcm09472
...
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6: (53 commits)
spi/omap2_mcspi: Verify TX reg is empty after TX only xfer with DMA
spi/omap2_mcspi: disable channel after TX_ONLY transfer in PIO mode
spi/bfin_spi: namespace local structs
spi/bfin_spi: init early
spi/bfin_spi: check per-transfer bits_per_word
spi/bfin_spi: warn when CS is driven by hardware (CPHA=0)
spi/bfin_spi: cs should be always low when a new transfer begins
spi/bfin_spi: fix typo in comment
spi/bfin_spi: reject unsupported SPI modes
spi/bfin_spi: use dma_disable_irq_nosync() in irq handler
spi/bfin_spi: combine duplicate SPI_CTL read/write logic
spi/bfin_spi: reset ctl_reg bits when setup is run again on a device
spi/bfin_spi: push all size checks into the transfer function
spi/bfin_spi: use nosync when disabling the IRQ from the IRQ handler
spi/bfin_spi: sync hardware state before reprogramming everything
spi/bfin_spi: save/restore state when suspending/resuming
spi/bfin_spi: redo GPIO CS handling
Blackfin: SPI: expand SPI bitmasks
spi/bfin_spi: use the SPI namespaced bit names
spi/bfin_spi: drop extra memory we don't need
...
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (96 commits)
apic, x86: Use BIOS settings for IBS and MCE threshold interrupt LVT offsets
apic, x86: Check if EILVT APIC registers are available (AMD only)
x86: ioapic: Call free_irte only if interrupt remapping enabled
arm: Use ARCH_IRQ_INIT_FLAGS
genirq, ARM: Fix boot on ARM platforms
genirq: Fix CONFIG_GENIRQ_NO_DEPRECATED=y build
x86: Switch sparse_irq allocations to GFP_KERNEL
genirq: Switch sparse_irq allocator to GFP_KERNEL
genirq: Make sparse_lock a mutex
x86: lguest: Use new irq allocator
genirq: Remove the now unused sparse irq leftovers
genirq: Sanitize dynamic irq handling
genirq: Remove arch_init_chip_data()
x86: xen: Sanitise sparse_irq handling
x86: Use sane enumeration
x86: uv: Clean up the direct access to irq_desc
x86: Make io_apic.c local functions static
genirq: Remove irq_2_iommu
x86: Speed up the irq_remapped check in hot pathes
intr_remap: Simplify the code further
...
Fix up trivial conflicts in arch/x86/Kconfig
* 'x86-vmware-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, paravirt: Remove alloc_pmd_clone hook, only used by VMI
x86, vmware: Remove deprecated VMI kernel support
Fix up trivial #include conflict in arch/x86/kernel/smpboot.c
* 'x86-bios-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, bios: Make the x86 early memory reservation a kernel option
x86, bios: By default, reserve the low 64K for all BIOSes
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (29 commits)
sched: Export account_system_vtime()
sched: Call tick_check_idle before __irq_enter
sched: Remove irq time from available CPU power
sched: Do not account irq time to current task
x86: Add IRQ_TIME_ACCOUNTING
sched: Add IRQ_TIME_ACCOUNTING, finer accounting of irq time
sched: Add a PF flag for ksoftirqd identification
sched: Consolidate account_system_vtime extern declaration
sched: Fix softirq time accounting
sched: Drop group_capacity to 1 only if local group has extra capacity
sched: Force balancing on newidle balance if local group has capacity
sched: Set group_imb only a task can be pulled from the busiest cpu
sched: Do not consider SCHED_IDLE tasks to be cache hot
sched: Drop all load weight manipulation for RT tasks
sched: Create special class for stop/migrate work
sched: Unindent labels
sched: Comment updates: fix default latency and granularity numbers
tracing/sched: Add sched_pi_setprio tracepoint
sched: Give CPU bound RT tasks preference
sched: Try not to migrate higher priority RT tasks
...
This patch adds IRQ_TIME_ACCOUNTING option on x86 and runtime enables it
when TSC is enabled.
This change just enables fine grained irq time accounting, isn't used yet.
Following patches use it for different purposes.
Signed-off-by: Venkatesh Pallipadi <venki@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1286237003-12406-6-git-send-email-venki@google.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
SoCs have a standard set of tuples consisting of frequency and
voltage pairs that the device will support per voltage domain. These
are called Operating Performance Points or OPPs. The actual
definitions of OPP varies over silicon versions. For a specific domain,
we can have a set of {frequency, voltage} pairs. As the kernel boots
and more information is available, a default set of these are activated
based on the precise nature of device. Further on operation, based on
conditions prevailing in the system (such as temperature), some OPP
availability may be temporarily controlled by the SoC frameworks.
To implement an OPP, some sort of power management support is necessary
hence this library depends on CONFIG_PM.
Contributions include:
Sanjeev Premi for the initial concept:
http://patchwork.kernel.org/patch/50998/
Kevin Hilman for converting original design to device-based.
Kevin Hilman and Paul Walmsey for cleaning up many of the function
abstractions, improvements and data structure handling.
Romit Dasgupta for using enums instead of opp pointers.
Thara Gopinath, Eduardo Valentin and Vishwanath BS for fixes and
cleanups.
Linus Walleij for recommending this layer be made generic for usage
in other architectures beyond OMAP and ARM.
Mark Brown, Andrew Morton, Rafael J. Wysocki, Paul E. McKenney for
valuable improvements.
Discussions and comments from:
http://marc.info/?l=linux-omap&m=126033945313269&w=2http://marc.info/?l=linux-omap&m=125482970102327&w=2http://marc.info/?t=125809247500002&r=1&w=2http://marc.info/?l=linux-omap&m=126025973426007&w=2http://marc.info/?t=128152609200064&r=1&w=2http://marc.info/?t=128468723000002&r=1&w=2
incorporated.
v1: http://marc.info/?t=128468723000002&r=1&w=2
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
If the device which fails to resume is part of a loadable kernel module
it won't be checked at startup against the magic number stored in the
RTC.
Add a read-only sysfs attribute /sys/power/pm_trace_dev_match which
contains a list of newline separated devices (usually just the one)
which currently match the last magic number. This allows the device
which is failing to resume to be found after the modules are loaded
again.
Signed-off-by: James Hogan <james@albanarts.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch (as1427) implements the "autosuspend" facility for runtime
PM. A few new fields are added to the dev_pm_info structure and
several new PM helper functions are defined, for telling the PM core
whether or not a device uses autosuspend, for setting the autosuspend
delay, and for marking periods of device activity.
Drivers that do not want to use autosuspend can continue using the
same helper functions as before; their behavior will not change. In
addition, drivers supporting autosuspend can also call the old helper
functions to get the old behavior.
The details are all explained in Documentation/power/runtime_pm.txt
and Documentation/ABI/testing/sysfs-devices-power.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Some devices, such as USB interfaces, cannot be power-managed
independently of their parents, i.e., they cannot be put in low power
while the parent remains at full power. This patch (as1425) creates a
new "no_callbacks" flag, which tells the PM core not to invoke the
runtime-PM callback routines for the such devices but instead to
assume that the callbacks always succeed. In addition, the
non-debugging runtime-PM sysfs attributes for the devices are removed,
since they are pretty much meaningless.
The advantage of this scheme comes not so much from avoiding the
callbacks themselves, but rather from the fact that without the need
for a process context in which to run the callbacks, more work can be
done in interrupt context.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Introduce struct wakeup_source for representing system wakeup sources
within the kernel and for collecting statistics related to them.
Make the recently introduced helper functions pm_wakeup_event(),
pm_stay_awake() and pm_relax() use struct wakeup_source objects
internally, so that wakeup statistics associated with wakeup devices
can be collected and reported in a consistent way (the definition of
pm_relax() is changed, which is harmless, because this function is
not called directly by anyone yet). Introduce new wakeup-related
sysfs device attributes in /sys/devices/.../power for reporting the
device wakeup statistics.
Change the global wakeup events counters event_count and
events_in_progress into atomic variables, so that it is not necessary
to acquire a global spinlock in pm_wakeup_event(), pm_stay_awake()
and pm_relax(), which should allow us to avoid lock contention in
these functions on SMP systems with many wakeup devices.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
The default hibernation image size is currently hard coded and euqal
to 500 MB, which is not a reasonable default on many contemporary
systems. Make it equal 2/5 of the total RAM size (this is slightly
below the maximum, i.e. 1/2 of the total RAM size, and seems to be
generally suitable).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: M. Vefa Bicakci <bicave@superonline.com>
Compress hibernation image with LZO in order to save on I/O and
therefore time to hibernate/thaw.
[rjw: Added hibernate=nocompress command line option instead of just
nocompress which would be confusing, fixed a couple of compiler
warnings, fixed kerneldoc comments, minor cleanups.]
Signed-off-by: Bojan Smojver <bojan@rexursive.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Update kprobes.txt about interrupts disabled state inside
kprobes handlers, because optimized probe/boosted kretprobe
run without disabling interrrupts on x86.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: 2nddept-manager@sdl.hitachi.co.jp
LKML-Reference: <20101014031018.4100.64883.stgit@ltc236.sdl.hitachi.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Also modifiy the document of cell-index in SPI controller. Add the
SPI flash(s25fl128p01) support on p4080ds and mpc8536ds board.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The page-types utility still uses an out of date name for the
unpoison interface: debugfs:hwpoison/renew-pfn
This patch renames and fixes it.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Acked-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Adds documentation for the e1000e networking driver.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updated the e1000 networking driver documentation.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the documentation for the ixgbevf (ixgbe virtual
function driver).
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of win_req_t, drivers are now requested to fill out
struct pcmcia_device *p_dev->resource[2,3,4,5] for up to four iomem
ranges. After a call to pcmcia_request_window(), the windows found there
are reserved and may be used until pcmcia_release_window() is called.
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-mtd@lists.infradead.org
CC: Jiri Kosina <jkosina@suse.cz>
CC: linux-scsi@vger.kernel.org
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The current tracing data is not sufficient to deduce the average time
that a callback spends waiting for a grace period to end. Add three
per-CPU counters recording the number of callbacks invoked (ci), the
number of callbacks orphaned (co), and the number of callbacks adopted
(ca). Given the existing callback queue length (ql), the average wait
time in absence of CPU hotplug operations is ql/ci. The units of wait
time will be in terms of the duration over which ci was measured.
In the presence of CPU hotplug operations, there is room for argument,
but ql/(ci-co+ca) won't steer you too far wrong.
Also fixes a typo called out by Lucas De Marchi <lucas.de.marchi@gmail.com>.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The attribute reflects an interval, not a rate.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
regulator: wm8350-regulator - fix the logic of checking REGULATOR_MODE_STANDBY mode
regulator: wm831x-ldo - fix the logic to set REGULATOR_MODE_IDLE and REGULATOR_MODE_STANDBY modes
regulator: ab8500 - fix off-by-one value range checking for selector
regulator: 88pm8607 - fix value range checking for accessing info->vol_table
regulator: isl6271a-regulator - fix regulator_desc parameter for regulator_register()
regulator: ad5398 - fix a memory leak
regulator: Update e-mail address for Liam Girdwood
regulator: set max8998->dev to &pdev->dev.
regulator: tps6586x-regulator - fix bit_mask parameter for tps6586x_set_bits()
regulator: tps6586x-regulator - fix value range checking for val
regulator: max8998 - set max8998->num_regulators
regulator: max8998 - fix memory allocation size for max8998->rdev
regulator: tps6507x - remove incorrect comments
regulator: max1586 - improve the logic of choosing selector
regulator: ab8500 - fix the logic to remove already registered regulators in error path
regulator: ab3100 - fix the logic to remove already registered regulators in error path
regulator/ab8500: move dereference below the check for NULL
Fix docbook templates that reference files that do not contain the
expected kernel-doc notation.
Fixes these warnings:
Warning(arch/x86/include/asm/unaligned.h): no structured comments found
Warning(lib/vsprintf.c): no structured comments found
These cause errors in the generated html output, like below, so drop
these lines.
Name
arch/x86/include/asm/unaligned.h - Document generation inconsistency
Oops
Warning
The template for this document tried to insert the structured comment from the file arch/x86/include/asm/unaligned.h at this point, but none was found. This dummy section is inserted to allow generation to continue.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When you don't use !E or !I but only !F, then it's very easy to miss
including some functions, structs etc. in documentation. To help
finding which ones were missed, allow printing out the unused ones as
warnings.
For example, using this on mac80211 yields a lot of warnings like this:
Warning: didn't use docs for DOC: mac80211 workqueue
Warning: didn't use docs for ieee80211_max_queues
Warning: didn't use docs for ieee80211_bss_change
Warning: didn't use docs for ieee80211_bss_conf
when generating the documentation for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: Range check cpu in blk_cpu_to_group
scatterlist: prevent invalid free when alloc fails
writeback: Fix lost wake-up shutting down writeback thread
writeback: do not lose wakeup events when forking bdi threads
cciss: fix reporting of max queue depth since init
block: switch s390 tape_block and mg_disk to elevator_change()
block: add function call to switch the IO scheduler from a driver
fs/bio-integrity.c: return -ENOMEM on kmalloc failure
bio-integrity.c: remove dependency on __GFP_NOFAIL
BLOCK: fix bio.bi_rw handling
block: put dev->kobj in blk_register_queue fail path
cciss: handle allocation failure
cfq-iosched: Documentation help for new tunables
cfq-iosched: blktrace print per slice sector stats
cfq-iosched: Implement tunable group_idle
cfq-iosched: Do group share accounting in IOPS when slice_idle=0
cfq-iosched: Do not idle if slice_idle=0
cciss: disable doorbell reset on reset_devices
blkio: Fix return code for mkdir calls
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: rawmidi: fix the get next midi device ioctl
ALSA: hda - Fix wrong HP pin detection in snd_hda_parse_pin_def_config()
ALSA: seq/oss - Fix double-free at error path of snd_seq_oss_open()
ALSA: msnd-classic: Fix invalid cfg parameter
ALSA: hda - Enable PC-beep for EeePC with ALC269 codec
ALSA: hda - Add errata initverb sequence for CS42xx codecs
ALSA: usb - Release capture substream URBs properly
ALSA: virtuoso: fix setting of Xonar DS line-in/mic-in controls
ALSA: virtuoso: work around missing reset in the Xonar DS Windows driver
ALSA: hda - Add quirk for Lenovo T400s
ALSA: usb-audio: fix detection of vendor-specific device protocol settings
ALSA: usb-audio: Assume first control interface is for audio
ALSA: hda - Add a new hp-laptop model for Conexant 5066, tested on HP G60
There's been some recent confusion about error checking GPIO numbers.
briefly, it should be handled mostly during setup, when gpio_request() is
called, and NEVER by expectig gpio_is_valid to report more than
never-usable GPIO numbers.
[akpm@linux-foundation.org: terminate unterminated comment]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Eric Miao" <eric.y.miao@gmail.com>
Cc: "Ryan Mallon" <ryan@bluewatersys.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Create attributes:
/sys/devices/system/cpu/cpuX/topology/book_id
/sys/devices/system/cpu/cpuX/topology/book_siblings
which show the book id and the book siblings of a cpu.
Unlike the attributes for SMT and MC these attributes are only present if
CONFIG_SCHED_BOOK is set. There is no reason to pollute sysfs for every
architecture with unused attributes.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <20100831082844.435648457@de.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
gcc-4.6: kernel/*: Fix unused but set warnings
mutex: Fix annotations to include it in kernel-locking docbook
pid: make setpgid() system call use RCU read-side critical section
MAINTAINERS: Add RCU's public git tree
