This patch removes a generic hard_header_len check from the usbnet
module that is causing dropped packages under certain circumstances
for devices that send rx packets that cross urb boundaries.
One example is the AX88772B which occasionally send rx packets that
cross urb boundaries where the remaining partial packet is sent with
no hardware header. When the buffer with a partial packet is of less
number of octets than the value of hard_header_len the buffer is
discarded by the usbnet module.
With AX88772B this can be reproduced by using ping with a packet
size between 1965-1976.
The bug has been reported here:
https://bugzilla.kernel.org/show_bug.cgi?id=29082
This patch introduces the following changes:
- Removes the generic hard_header_len check in the rx_complete
function in the usbnet module.
- Introduces a ETH_HLEN check for skbs that are not cloned from
within a rx_fixup callback.
- For safety a hard_header_len check is added to each rx_fixup
callback function that could be affected by this change.
These extra checks could possibly be removed by someone
who has the hardware to test.
- Removes a call to dev_kfree_skb_any() and instead utilizes the
dev->done list to queue skbs for cleanup.
The changes place full responsibility on the rx_fixup callback
functions that clone skbs to only pass valid skbs to the
usbnet_skb_return function.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Reported-by: Igor Gnatenko <i.gnatenko.brain@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new argument for ndo_select_queue() callback that passes a
fallback handler. This gets invoked through netdev_pick_tx();
fallback handler is currently __netdev_pick_tx() as most drivers
invoke this function within their customized implementation in
case for skbs that don't need any special handling. This fallback
handler can then be replaced on other call-sites with different
queue selection methods (e.g. in packet sockets, pktgen etc).
This also has the nice side-effect that __netdev_pick_tx() is
then only invoked from netdev_pick_tx() and export of that
function to modules can be undone.
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise the device is not completely shut down.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this patch, the "cat /sys/class/net/ethN/operstate" shows
"unknown", and "ethtool ethN" shows "Link detected: yes", when VM
boots up with or without vNIC connected.
This patch fixed the problem.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/bonding/bond_options.c includes rwlock.h directly,
which is a nono, and which also breaks RT kernel build.
Signed-off-by: Mike Galbraith <bitbucket@online.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8fdade4 ("net: of_mdio: parse "max-speed" property to set PHY
supported features") introduced a typo in of_set_phy_supported for the
first assignment of phydev->supported which will not effectively limit
the PHY device supported features bits if the PHY driver contains
"higher" features (e.g: max-speed = <100> and PHY driver has
PHY_GBIT_FEATURES set).
Fix this by making sure that the very first thing is to reset to sane
defaults (PHY_BASIC_FEATURES) and then progressively add speed features
as we parse them.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The struct driver_info ax88178_info is assigned the function
asix_rx_fixup_common as it's rx_fixup callback. This means that
FLAG_MULTI_PACKET must be set as this function is cloning the
data and calling usbnet_skb_return. Not setting this flag leads
to usbnet_skb_return beeing called a second time from within
the rx_process function in the usbnet module.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Reported-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_init_hw not does a full PHY reset after the driver probe has
finished, so any hw initialization done in the probe will be lost.
Part of the timestamping functionality of the dp83640 is set up in the
probe and with that lost, enabling timestamping will cause a PHY
lockup, requiring a hard reset / power cycle to recover.
This patch moves all the HW initialization in dp83640_probe to
dp83640_config_init.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 0cd8f9cc0654c06adde353c6532114c5f53a18e8 ("drivers: net: cpsw:
enable promiscuous mode support")
Enable promiscuous mode support for CPSW.
Introduced a crash on an am335x based board (similiar to am335x-evm).
Reason is buggy end condition in for loop in cpsw_set_promiscious()
for (i = 0; i <= priv->data.slaves; i++)
should be
for (i = 0; i < priv->data.slaves; i++)
Fix this ...
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Daniel Mack <zonque@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Markus Pargmann <mpa@pengutronix.de>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vhost_zerocopy_callback accesses VQ right after it drops a ubuf
reference. In theory, this could race with device removal which waits
on the ubuf kref, and crash on use after free.
Do all accesses within rcu read side critical section, and synchronize
on release.
Since callbacks are always invoked from bh, synchronize_rcu_bh seems
enough and will help release complete a bit faster.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vhost checked the counter within the refcnt before decrementing. It
really wanted to know that it is the one that has the last reference, as
a way to batch freeing resources a bit more efficiently.
Note: we only let refcount go to 0 on device release.
This works well but we now access the ref counter twice so there's a
race: all users might see a high count and decide to defer freeing
resources.
In the end no one initiates freeing resources until the last reference
is gone (which is on VM shotdown so might happen after a looooong time).
Let's do what we probably should have done straight away:
switch from kref to plain atomic, documenting the
semantics, return the refcount value atomically after decrement,
then use that to avoid the deadlock.
Reported-by: Qin Chuanyu <qinchuanyu@huawei.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use %zu for size_t in order to avoid the following build
warning in printks.
drivers/net/usb/sr9800.c: In function 'sr9800_bind'
drivers/net/usb/sr9800.c:826:2: warning: format '%ld' expects argument of type 'long int' but argument 5 has type 'size_t'
[-Wformat]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's wrong if the device tree doesn't provide a phy-mode property for
the cpsw slaves as it is documented to be required in
Documentation/devicetree/bindings/net/cpsw.txt.
Anyhow it's nice to catch that problem, still more as it used to work
without this property up to commit 388367a5a9fb (drivers: net: cpsw: use
cpsw-phy-sel driver to configure phy mode) which is in v3.13-rc1.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the PXS8 and PHS8 devices show up with PID 0x0053 they will expose both a
QMI port and a WWAN interface.
CC: Hans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com>
CC: Christian Schmiedl <christian.schmiedl@gemalto.com>
CC: Nicolaus Colberg <nicolaus.colberg@gemalto.com>
CC: David McCullough <david.mccullough@accelecon.com>
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlL7SvUACgkQjTAFq1RaXHNKIgCfQ4bisAc/ZZrqfa6R9uXTsb4J
+toAnAs4U0U453IWMutrshb4gaAGrOaG
=IWyw
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-3.14-20140212' of git://gitorious.org/linux-can/linux-can
linux-can-fixes-for-3.14-20140212
Marc Kleine-Budde says:
====================
this is a pull request with one patch for net/master, for the current release
cycle. Olivier Sobrie noticed and fixed that the kvaser_usb driver doesn't
check the number of channels value from the hardware, which may result in
writing over the bounds of an array in the driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Warning log:
xilinx_axienet_main.c: In function 'axienet_start_xmit_done':
xilinx_axienet_main.c:617:16: warning: operation on 'lp->tx_bd_ci' may be undefined [-Wsequence-point]
xilinx_axienet_main.c: In function 'axienet_start_xmit':
xilinx_axienet_main.c:703:18: warning: operation on 'lp->tx_bd_tail' may be undefined [-Wsequence-point]
xilinx_axienet_main.c:719:17: warning: operation on 'lp->tx_bd_tail' may be undefined [-Wsequence-point]
xilinx_axienet_main.c: In function 'axienet_recv':
xilinx_axienet_main.c:792:16: warning: operation on 'lp->rx_bd_ci' may be undefined [-Wsequence-point]
xilinx_axienet_main.c: In function 'axienet_of_probe':
xilinx_axienet_main.c:1501:21: warning: unused variable 'rc' [-Wunused-variable]
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bonding driver take write locks and spin locks that are shared
by the tx path in enslave processing and notification processing,
If the netconsole is in use, the bonding can call printk which puts
us in the netpoll tx path, if the netconsole is attached to the bonding
driver, result in deadlock.
So add protection for these place, by checking the netpoll_block_tx
state, we can defer the sending of the netconsole frames until a later
time using the retransmit feature of netpoll_send_skb that is triggered
on the return code NETDEV_TX_BUSY.
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtnl_newlink() doesn't unregister it for us on failure.
Cc: Patrick McHardy <kaber@trash.net>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
STi series SOCs have a glue layer on top of the synopsis gmac IP, this
glue layer needs to be configured before the gmac driver starts using
the IP.
This patch adds a support to this glue layer which is configured via
stmmac setup, init, exit callbacks.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netlink kind (and iproute2 type option) is actually called
'macvtap', not 'macvlan'.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
remove_proc_subtree() doesn't work here as local->ddev has already
been removed, and NULLed out. Use proc_remove() instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes regression caused by commit a16dad77634 "MIPS: Fix
potencial corruption". That commit fixes one corruption scenario in
cost of adding another one, which actually start to cause crashes
on Yeeloong laptop when rtl8187 driver is used.
For correct DMA read operation on machines without DMA coherence, kernel
have to invalidate cache, such it will refill later with new data that
device wrote to memory, when that data is needed to process. We can only
invalidate full cache line. Hence when cache line includes both dma
buffer and some other data (written in cache, but not yet in main
memory), the other data can not hit memory due to invalidation. That
happen on rtl8187 where struct rtl8187_priv fields are located just
before and after small buffers that are passed to USB layer and DMA
is performed on them.
To fix the problem we align buffers and reserve space after them to make
them match cache line.
This patch does not resolve all possible MIPS problems entirely, for
that we have to assure that we always map cache aligned buffers for DMA,
what can be complex or even not possible. But patch fixes visible and
reproducible regression and seems other possible corruptions do not
happen in practice, since Yeeloong laptop works stable without rtl8187
driver.
Bug report:
https://bugzilla.kernel.org/show_bug.cgi?id=54391
Reported-by: Petr Pisar <petr.pisar@atlas.cz>
Bisected-by: Tom Li <biergaizi2009@gmail.com>
Reported-and-tested-by: Tom Li <biergaizi2009@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Larry Finger <Larry.Finger@lwfinger.next>
Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the original code we shift "AR5K_PHY(256) >> 28" which is zero but
the intent was to shift the return value of ath5k_hw_reg_read() like we
do a couple lines later.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rtl_ps_enable_nic() is called from loops that will loop until this function returns true or a
maximum number of retries is performed.
hw_init() returns non-zero on error. In that situation return false to
restore the original design intent to retry hw init when it fails.
Signed-off-by: Olivier Langlois <olivier@trillion01.com>
Cc: Stable <stable@vger.kernel.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rtl8192ce is disabling for too long the local interrupts during hw initiatialisation when performing scans
The observable symptoms in dmesg can be:
- underruns from ALSA playback
- clock freezes (tstamps do not change for several dmesg entries until irqs are finaly reenabled):
[ 250.817669] rtlwifi:rtl_op_config():<0-0-0> 0x100
[ 250.817685] rtl8192ce:_rtl92ce_phy_set_rf_power_state():<0-1-0> IPS Set eRf nic enable
[ 250.817732] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.817796] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.817910] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.818024] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.818139] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.818253] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.818367] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.818472] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.818472] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.818472] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.818472] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:18051d59:11
[ 250.818472] rtl8192ce:_rtl92ce_init_mac():<0-1-0> reg0xec:98053f15:10
[ 250.818472] rtl8192ce:rtl92ce_sw_led_on():<0-1-0> LedAddr:4E ledpin=1
[ 250.818472] rtl8192c_common:rtl92c_download_fw():<0-1-0> Firmware Version(49), Signature(0x88c1),Size(32)
[ 250.818472] rtl8192ce:rtl92ce_enable_hw_security_config():<0-1-0> PairwiseEncAlgorithm = 0 GroupEncAlgorithm = 0
[ 250.818472] rtl8192ce:rtl92ce_enable_hw_security_config():<0-1-0> The SECR-value cc
[ 250.818472] rtl8192c_common:rtl92c_dm_check_txpower_tracking_thermal_meter():<0-1-0> Schedule TxPowerTracking direct call!!
[ 250.818472] rtl8192c_common:rtl92c_dm_txpower_tracking_callback_thermalmeter():<0-1-0> rtl92c_dm_txpower_tracking_callback_thermalmeter
[ 250.818472] rtl8192c_common:rtl92c_dm_txpower_tracking_callback_thermalmeter():<0-1-0> Readback Thermal Meter = 0xe pre thermal meter 0xf eeprom_thermalmeter 0xf
[ 250.818472] rtl8192c_common:rtl92c_dm_txpower_tracking_callback_thermalmeter():<0-1-0> Initial pathA ele_d reg0xc80 = 0x40000000, ofdm_index=0xc
[ 250.818472] rtl8192c_common:rtl92c_dm_txpower_tracking_callback_thermalmeter():<0-1-0> Initial reg0xa24 = 0x90e1317, cck_index=0xc, ch14 0
[ 250.818472] rtl8192c_common:rtl92c_dm_txpower_tracking_callback_thermalmeter():<0-1-0> Readback Thermal Meter = 0xe pre thermal meter 0xf eeprom_thermalmeter 0xf delta 0x1 delta_lck 0x0 delta_iqk 0x0
[ 250.818472] rtl8192c_common:rtl92c_dm_txpower_tracking_callback_thermalmeter():<0-1-0> <===
[ 250.818472] rtl8192c_common:rtl92c_dm_initialize_txpower_tracking_thermalmeter():<0-1-0> pMgntInfo->txpower_tracking = 1
[ 250.818472] rtl8192ce:rtl92ce_led_control():<0-1-0> ledaction 3
[ 250.818472] rtl8192ce:rtl92ce_sw_led_on():<0-1-0> LedAddr:4E ledpin=1
[ 250.818472] rtlwifi:rtl_ips_nic_on():<0-1-0> before spin_unlock_irqrestore
[ 251.154656] PCM: Lost interrupts? [Q]-0 (stream=0, delta=15903, new_hw_ptr=293408, old_hw_ptr=277505)
The exact code flow that causes that is:
1. wpa_supplicant send a start_scan request to the nl80211 driver
2. mac80211 module call rtl_op_config with IEEE80211_CONF_CHANGE_IDLE
3. rtl_ips_nic_on is called which disable local irqs
4. rtl92c_phy_set_rf_power_state() is called
5. rtl_ps_enable_nic() is called and hw_init()is executed and then the interrupts on the device are enabled
A good solution could be to refactor the code to avoid calling rtl92ce_hw_init() with the irqs disabled
but a quick and dirty solution that has proven to work is
to reenable the irqs during the function rtl92ce_hw_init().
I think that it is safe doing so since the device interrupt will only be enabled after the init function succeed.
Signed-off-by: Olivier Langlois <olivier@trillion01.com>
Cc: Stable <stable@vger.kernel.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
NICs supported by iwldvm don't handle well TX AMPDU.
Disable it by default, still leave the possibility to
the user to force enable it with a debug parameter.
NICs supported by iwlmvm don't suffer from the same issue,
leave TX AMPDU enabled by default for these.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
It is needed to check the number of channels returned by the HW because it
cannot be greater than MAX_NET_DEVICES otherwise it will crash.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Pull s390 bugfixes from Martin Schwidefsky:
"A collection a bug fixes. Most of them are minor but two of them are
more severe. The linkage stack bug can be used by user space to force
an oops, with panic_on_oops this is a denial-of-service. And the dump
memory detection issue can cause incomplete memory dumps"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/cio: improve cio_commit_config
s390: fix kernel crash due to linkage stack instructions
s390/dump: Fix dump memory detection
s390/appldata: restore missing init_virt_timer()
s390/qdio: correct program-controlled interruption checking
s390/qdio: for_each macro correctness
Pull networking updates from David Miller:
1) Fix flexcan build on big endian, from Arnd Bergmann
2) Correctly attach cpsw to GPIO bitbang MDIO drive, from Stefan Roese
3) udp_add_offload has to use GFP_ATOMIC since it can be invoked from
non-sleepable contexts. From Or Gerlitz
4) vxlan_gro_receive() does not iterate over all possible flows
properly, fix also from Or Gerlitz
5) CAN core doesn't use a proper SKB destructor when it hooks up
sockets to SKBs. Fix from Oliver Hartkopp
6) ip_tunnel_xmit() can use an uninitialized route pointer, fix from
Eric Dumazet
7) Fix address family assignment in IPVS, from Michal Kubecek
8) Fix ath9k build on ARM, from Sujith Manoharan
9) Make sure fail_over_mac only applies for the correct bonding modes,
from Ding Tianhong
10) The udp offload code doesn't use RCU correctly, from Shlomo Pongratz
11) Handle gigabit features properly in generic PHY code, from Florian
Fainelli
12) Don't blindly invoke link operations in
rtnl_link_get_slave_info_data_size, they are optional. Fix from
Fernando Luis Vazquez Cao
13) Add USB IDs for Netgear Aircard 340U, from Bjørn Mork
14) Handle netlink packet padding properly in openvswitch, from Thomas
Graf
15) Fix oops when deleting chains in nf_tables, from Patrick McHardy
16) Fix RX stalls in xen-netback driver, from Zoltan Kiss
17) Fix deadlock in mac80211 stack, from Emmanuel Grumbach
18) inet_nlmsg_size() forgets to consider ifa_cacheinfo, fix from Geert
Uytterhoeven
19) tg3_change_mtu() can deadlock, fix from Nithin Sujir
20) Fix regression in setting SCTP local source addresses on accepted
sockets, caused by some generic ipv6 socket changes. Fix from
Matija Glavinic Pecotic
21) IPPROTO_* must be pure defines, otherwise module aliases don't get
constructed properly. Fix from Jan Moskyto
22) IPV6 netconsole setup doesn't work properly unless an explicit
source address is specified, fix from Sabrina Dubroca
23) Use __GFP_NORETRY for high order skb page allocations in
sock_alloc_send_pskb and skb_page_frag_refill. From Eric Dumazet
24) Fix a regression added in netconsole over bridging, from Cong Wang
25) TCP uses an artificial offset of 1ms for SRTT, but this doesn't jive
well with TCP pacing which needs the SRTT to be accurate. Fix from
Eric Dumazet
26) Several cases of missing header file includes from Rashika Kheria
27) Add ZTE MF667 device ID to qmi_wwan driver, from Raymond Wanyoike
28) TCP Small Queues doesn't handle nonagle properly in some corner
cases, fix from Eric Dumazet
29) Remove extraneous read_unlock in bond_enslave, whoops. From Ding
Tianhong
30) Fix 9p trans_virtio handling of vmalloc buffers, from Richard Yao
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (136 commits)
6lowpan: fix lockdep splats
alx: add missing stats_lock spinlock init
9p/trans_virtio.c: Fix broken zero-copy on vmalloc() buffers
bonding: remove unwanted bond lock for enslave processing
USB2NET : SR9800 : One chip USB2.0 USB2NET SR9800 Device Driver Support
tcp: tsq: fix nonagle handling
bridge: Prevent possible race condition in br_fdb_change_mac_address
bridge: Properly check if local fdb entry can be deleted when deleting vlan
bridge: Properly check if local fdb entry can be deleted in br_fdb_delete_by_port
bridge: Properly check if local fdb entry can be deleted in br_fdb_change_mac_address
bridge: Fix the way to check if a local fdb entry can be deleted
bridge: Change local fdb entries whenever mac address of bridge device changes
bridge: Fix the way to find old local fdb entries in br_fdb_change_mac_address
bridge: Fix the way to insert new local fdb entries in br_fdb_changeaddr
bridge: Fix the way to find old local fdb entries in br_fdb_changeaddr
tcp: correct code comment stating 3 min timeout for FIN_WAIT2, we only do 1 min
net: vxge: Remove unused device pointer
net: qmi_wwan: add ZTE MF667
3c59x: Remove unused pointer in vortex_eisa_cleanup()
net: fix 'ip rule' iif/oif device rename
...
Trivial fix for init time stack trace occuring in
alx_get_stats64 upon start up. Should have been part of
commit adding the spinlock:
f1b6b106 alx: add alx_get_stats64 operation
Signed-off-by: John Greene <jogreene@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bond enslave processing don't hold bond->lock anymore,
so release an unlocked rw lock will cause warning message,
remove the unwanted read_unlock(&bond->lock).
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/md/bcache/extents.c: In function `btree_ptr_bad_expensive':
drivers/md/bcache/extents.c:196: warning: format `%li' expects type `long int', but argument 4 has type `size_t'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Kent Overstreet <kmo@daterainc.com>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
i2o_cfg_compat_ioctl(I2OGETIOPS) locks i2o_cfg_mutex and then calls
i2o_cfg_ioctl(I2OGETIOPS) that locks i2o_cfg_mutex as well. A deadlock
is guaranteed.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I was reviewing this and noticed that unlocking should be conditional on
the error path. I've changed it to unlock and return directly since we
only do it once and it seems unlikely to change in the near future.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Dimitri Sivanich <sivanich@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove occurrences of unused struct __vxge_hw_device pointer in functions
vxge_learn_mac() and vxge_rem_isr().
Detected by Coverity: CID 139839, CID 139842.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver description files give these descriptions to the vendor specific
ports on this modem:
VID_19D2&PID_1270&MI_00: "ZTE MF667 Diagnostics Port"
VID_19D2&PID_1270&MI_01: "ZTE MF667 AT Port"
VID_19D2&PID_1270&MI_02: "ZTE MF667 ATExt2 Port"
VID_19D2&PID_1270&MI_03: "ZTE MF667 ATExt Port"
VID_19D2&PID_1270&MI_04: "ZTE MF667 USB Modem"
VID_19D2&PID_1270&MI_05: "ZTE MF667 Network Adapter"
Signed-off-by: Raymond Wanyoike <raymond.wanyoike@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unused network device private data pointer 'vp' in function
vortex_eisa_cleanup(). Detected by Coverity: CID 139826.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove occurrences of unused pointer to network device private data in
functions dlci_header() and dlci_receive().
Detected by Coverity: CID 139844, CID 139845.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull vfs fixes from Al Viro:
"A couple of fixes, both -stable fodder. The O_SYNC bug is fairly
old..."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fix a kmap leak in virtio_console
fix O_SYNC|O_APPEND syncing the wrong range on write()
John W. Linville says:
====================
Please pull this batch of fixes intended for the 3.14 stream!
For the mac80211 bits, Johannes says:
"This is just a collection of small fixes, the commit logs explain the
details. The only thing that isn't strictly a fix is the 5/10 MHz
enabling, I had forgotten this and there's little point in waiting
longer. The patch simply removes the force-disable code that I put in
when there was a problem with the userspace API (that has long been
fixed.)"
For the iwlwifi bits, Emmanuel says:
"I have an important fix that disables A band in case the driver thought
it was enabled, and the firmware disagreed. We ended up making the
firmware unhappy. I also fix the station table in AP mode and fix the
scan while we have BT working.
Johannes removes a static variable that could potentially lead to to
issues on multi-device setups and disables scheduled scan to avoid
issues with old versions of wpa_supplicant.
A small fix from David on scan and a few new device IDs for 7265."
On top of that...
Oleksij Rempel adds a USB ID to the ar5523 driver and changes the
default powersave setting for ath9k_htc to "off", due to observed
stability issues (based on an equivalent ath9k patch).
Stanislaw Gruszka similarly disables powersave for a couple of rt2x00
drivers. He also fixes a couple of scheduling while atomic issues
in ath9k_htc.
Sujith Manoharan rounds-out the powersave disables with one for ath9k.
He also fixes a build prolem with ath9k on ARM and fixes an ath9k Tx
power calculation.
Finally, Andrea Merello fixes a couple of lingering DMA mapping
problems in the rtl8180 driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
While we are at it, don't do kmap() under kmap_atomic(), *especially*
for a page we'd allocated with GFP_KERNEL. It's spelled "page_address",
and had that been more than that, we'd have a real trouble - kmap_high()
can block, and doing that while holding kmap_atomic() is a Bad Idea(tm).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
- Protect pinctrl_list_add() with the proper mutex. This
was identified by RedHat. Caused nasty locking warnings
was rootcased by Stanislaw Gruszka.
- Avoid adding dangerous debugfs files when either half of
the subsystem is unused: pinmux or pinconf.
- Various fixes to various drivers: locking, hardware
particulars, DT parsing, error codes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=pxHE
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v3.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl fixes from Linus Walleij:
"First round of pin control fixes for v3.14:
- Protect pinctrl_list_add() with the proper mutex. This was
identified by RedHat. Caused nasty locking warnings was rootcased
by Stanislaw Gruszka.
- Avoid adding dangerous debugfs files when either half of the
subsystem is unused: pinmux or pinconf.
- Various fixes to various drivers: locking, hardware particulars, DT
parsing, error codes"
* tag 'pinctrl-v3.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: tegra: return correct error type
pinctrl: do not init debugfs entries for unimplemented functionalities
pinctrl: protect pinctrl_list add
pinctrl: sirf: correct the pin index of ac97_pins group
pinctrl: imx27: fix offset calculation in imx_read_2bit
pinctrl: vt8500: Change devicetree data parsing
pinctrl: imx27: fix wrong offset to ICONFB
pinctrl: at91: use locked variant of irq_set_handler
On archs like S390 or um this driver cannot build nor work.
Make it depend on HAS_IOMEM to bypass build failures.
drivers/built-in.o: In function `dw_wdt_drv_probe':
drivers/watchdog/dw_wdt.c:302: undefined reference to `devm_ioremap_resource'
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Pull media fixes from Mauro Carvalho Chehab:
"A series of small fixes. Mostly driver ones. There is one core
regression fix on a patch that was meant to fix some race issues on
vb2, but that actually caused more harm than good. So, we're just
reverting it for now"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] adv7842: Composite free-run platfrom-data fix
[media] v4l2-dv-timings: fix GTF calculation
[media] hdpvr: Fix memory leak in debug
[media] af9035: add ID [2040:f900] Hauppauge WinTV-MiniStick 2
[media] mxl111sf: Fix compile when CONFIG_DVB_USB_MXL111SF is unset
[media] mxl111sf: Fix unintentional garbage stack read
[media] cx24117: use a valid dev pointer for dev_err printout
[media] cx24117: remove dead code in always 'false' if statement
[media] update Michael Krufky's email address
[media] vb2: Check if there are buffers before streamon
[media] Revert "[media] videobuf_vm_{open,close} race fixes"
[media] go7007-loader: fix usb_dev leak
[media] media: bt8xx: add missing put_device call
[media] exynos4-is: Compile in fimc-lite runtime PM callbacks conditionally
[media] exynos4-is: Compile in fimc runtime PM callbacks conditionally
[media] exynos4-is: Fix error paths in probe() for !pm_runtime_enabled()
[media] s5p-jpeg: Fix wrong NV12 format parameters
[media] s5k5baf: allow to handle arbitrary long i2c sequences
