linux-next/Documentation/devicetree/bindings/phy/ti,phy-gmii-sel.yaml

# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
# Copyright (C) 2020 Texas Instruments Incorporated - http://www.ti.com/
%YAML 1.2
---
$id: "http://devicetree.org/schemas/phy/ti,phy-gmii-sel.yaml#"
$schema: "http://devicetree.org/meta-schemas/core.yaml#"

title: CPSW Port's Interface Mode Selection PHY

maintainers:
  - Kishon Vijay Abraham I <kishon@ti.com>

description: |
  TI am335x/am437x/dra7(am5)/dm814x CPSW3G Ethernet Subsystem supports
  two 10/100/1000 Ethernet ports with selectable G/MII, RMII, and RGMII interfaces.
  The interface mode is selected by configuring the MII mode selection register(s)
  (GMII_SEL) in the System Control Module chapter (SCM). GMII_SEL register(s) and
  bit fields placement in SCM are different between SoCs while fields meaning
  is the same.
                                               +--------------+
        +-------------------------------+      |SCM           |
        |                     CPSW      |      |  +---------+ |
        |        +--------------------------------+gmii_sel | |
        |        |                      |      |  +---------+ |
        |   +----v---+     +--------+   |      +--------------+
        |   |Port 1..<--+-->GMII/MII<------->
        |   |        |  |  |        |   |
        |   +--------+  |  +--------+   |
        |               |               |
        |               |  +--------+   |
        |               |  | RMII   <------->
        |               +-->        |   |
        |               |  +--------+   |
        |               |               |
        |               |  +--------+   |
        |               |  | RGMII  <------->
        |               +-->        |   |
        |                  +--------+   |
        +-------------------------------+

  CPSW Port's Interface Mode Selection PHY describes MII interface mode between
  CPSW Port and Ethernet PHY which depends on Eth PHY and board configuration.
  |
  CPSW Port's Interface Mode Selection PHY device should defined as child device
  of SCM node (scm_conf) and can be attached to each CPSW port node using standard
  PHY bindings.

properties:
  compatible:
    enum:
      - ti,am3352-phy-gmii-sel
      - ti,dra7xx-phy-gmii-sel
      - ti,am43xx-phy-gmii-sel
      - ti,dm814-phy-gmii-sel
      - ti,am654-phy-gmii-sel
      - ti,j7200-cpsw5g-phy-gmii-sel
      - ti,j721e-cpsw9g-phy-gmii-sel

  reg:
    maxItems: 1

  '#phy-cells': true

  ti,qsgmii-main-ports:
    $ref: /schemas/types.yaml#/definitions/uint32-array
    description: |
      Required only for QSGMII mode. Array to select the port/s for QSGMII
      main mode. The size of the array corresponds to the number of QSGMII
      interfaces and thus, the number of distinct QSGMII main ports,
      supported by the device. If the device supports two QSGMII interfaces
      but only one QSGMII interface is desired, repeat the QSGMII main port
      value corresponding to the QSGMII interface in the array.
    minItems: 1
    maxItems: 2
    items:
      minimum: 1
      maximum: 8

allOf:
  - if:
      properties:
        compatible:
          contains:
            enum:
              - ti,dra7xx-phy-gmii-sel
              - ti,dm814-phy-gmii-sel
              - ti,am654-phy-gmii-sel
              - ti,j7200-cpsw5g-phy-gmii-sel
              - ti,j721e-cpsw9g-phy-gmii-sel
    then:
      properties:
        '#phy-cells':
          const: 1
          description: CPSW port number (starting from 1)

  - if:
      properties:
        compatible:
          contains:
            enum:
              - ti,j7200-cpsw5g-phy-gmii-sel
    then:
      properties:
        ti,qsgmii-main-ports:
          maxItems: 1
          items:
            minimum: 1
            maximum: 4

  - if:
      properties:
        compatible:
          contains:
            enum:
              - ti,j721e-cpsw9g-phy-gmii-sel
    then:
      properties:
        ti,qsgmii-main-ports:
          minItems: 2
          maxItems: 2
          items:
            minimum: 1
            maximum: 8

  - if:
      not:
        properties:
          compatible:
            contains:
              enum:
                - ti,j7200-cpsw5g-phy-gmii-sel
                - ti,j721e-cpsw9g-phy-gmii-sel
    then:
      properties:
        ti,qsgmii-main-ports: false

  - if:
      properties:
        compatible:
          contains:
            enum:
              - ti,am3352-phy-gmii-sel
              - ti,am43xx-phy-gmii-sel
    then:
      properties:
        '#phy-cells':
          const: 2
          description: |
            - CPSW port number (starting from 1)
            - RMII refclk mode

required:
  - compatible
  - reg
  - '#phy-cells'

additionalProperties: false

examples:
  - |
    phy_gmii_sel: phy@650 {
        compatible = "ti,am3352-phy-gmii-sel";
        reg = <0x650 0x4>;
        #phy-cells = <2>;
    };