linux-stable/drivers/net/pse-pd/pse_core.c

901 lines
20 KiB
C
Raw Normal View History

// SPDX-License-Identifier: GPL-2.0-only
//
// Framework for Ethernet Power Sourcing Equipment
//
// Copyright (c) 2022 Pengutronix, Oleksij Rempel <kernel@pengutronix.de>
//
#include <linux/device.h>
#include <linux/of.h>
#include <linux/pse-pd/pse.h>
#include <linux/regulator/driver.h>
#include <linux/regulator/machine.h>
static DEFINE_MUTEX(pse_list_mutex);
static LIST_HEAD(pse_controller_list);
/**
* struct pse_control - a PSE control
* @pcdev: a pointer to the PSE controller device
* this PSE control belongs to
* @ps: PSE PI supply of the PSE control
* @list: list entry for the pcdev's PSE controller list
* @id: ID of the PSE line in the PSE controller device
* @refcnt: Number of gets of this pse_control
*/
struct pse_control {
struct pse_controller_dev *pcdev;
struct regulator *ps;
struct list_head list;
unsigned int id;
struct kref refcnt;
};
static int of_load_single_pse_pi_pairset(struct device_node *node,
struct pse_pi *pi,
int pairset_num)
{
struct device_node *pairset_np;
const char *name;
int ret;
ret = of_property_read_string_index(node, "pairset-names",
pairset_num, &name);
if (ret)
return ret;
if (!strcmp(name, "alternative-a")) {
pi->pairset[pairset_num].pinout = ALTERNATIVE_A;
} else if (!strcmp(name, "alternative-b")) {
pi->pairset[pairset_num].pinout = ALTERNATIVE_B;
} else {
pr_err("pse: wrong pairset-names value %s (%pOF)\n",
name, node);
return -EINVAL;
}
pairset_np = of_parse_phandle(node, "pairsets", pairset_num);
if (!pairset_np)
return -ENODEV;
pi->pairset[pairset_num].np = pairset_np;
return 0;
}
/**
* of_load_pse_pi_pairsets - load PSE PI pairsets pinout and polarity
* @node: a pointer of the device node
* @pi: a pointer of the PSE PI to fill
* @npairsets: the number of pairsets (1 or 2) used by the PI
*
* Return: 0 on success and failure value on error
*/
static int of_load_pse_pi_pairsets(struct device_node *node,
struct pse_pi *pi,
int npairsets)
{
int i, ret;
ret = of_property_count_strings(node, "pairset-names");
if (ret != npairsets) {
pr_err("pse: amount of pairsets and pairset-names is not equal %d != %d (%pOF)\n",
npairsets, ret, node);
return -EINVAL;
}
for (i = 0; i < npairsets; i++) {
ret = of_load_single_pse_pi_pairset(node, pi, i);
if (ret)
goto out;
}
if (npairsets == 2 &&
pi->pairset[0].pinout == pi->pairset[1].pinout) {
pr_err("pse: two PI pairsets can not have identical pinout (%pOF)",
node);
ret = -EINVAL;
}
out:
/* If an error appears, release all the pairset device node kref */
if (ret) {
of_node_put(pi->pairset[0].np);
pi->pairset[0].np = NULL;
of_node_put(pi->pairset[1].np);
pi->pairset[1].np = NULL;
}
return ret;
}
static void pse_release_pis(struct pse_controller_dev *pcdev)
{
int i;
for (i = 0; i <= pcdev->nr_lines; i++) {
of_node_put(pcdev->pi[i].pairset[0].np);
of_node_put(pcdev->pi[i].pairset[1].np);
of_node_put(pcdev->pi[i].np);
}
kfree(pcdev->pi);
}
/**
* of_load_pse_pis - load all the PSE PIs
* @pcdev: a pointer to the PSE controller device
*
* Return: 0 on success and failure value on error
*/
static int of_load_pse_pis(struct pse_controller_dev *pcdev)
{
struct device_node *np = pcdev->dev->of_node;
struct device_node *node, *pis;
int ret;
if (!np)
return -ENODEV;
pcdev->pi = kcalloc(pcdev->nr_lines, sizeof(*pcdev->pi), GFP_KERNEL);
if (!pcdev->pi)
return -ENOMEM;
pis = of_get_child_by_name(np, "pse-pis");
if (!pis) {
/* no description of PSE PIs */
pcdev->no_of_pse_pi = true;
return 0;
}
for_each_child_of_node(pis, node) {
struct pse_pi pi = {0};
u32 id;
if (!of_node_name_eq(node, "pse-pi"))
continue;
ret = of_property_read_u32(node, "reg", &id);
if (ret) {
dev_err(pcdev->dev,
"can't get reg property for node '%pOF'",
node);
goto out;
}
if (id >= pcdev->nr_lines) {
dev_err(pcdev->dev,
"reg value (%u) is out of range (%u) (%pOF)\n",
id, pcdev->nr_lines, node);
ret = -EINVAL;
goto out;
}
if (pcdev->pi[id].np) {
dev_err(pcdev->dev,
"other node with same reg value was already registered. %pOF : %pOF\n",
pcdev->pi[id].np, node);
ret = -EINVAL;
goto out;
}
ret = of_count_phandle_with_args(node, "pairsets", NULL);
/* npairsets is limited to value one or two */
if (ret == 1 || ret == 2) {
ret = of_load_pse_pi_pairsets(node, &pi, ret);
if (ret)
goto out;
} else if (ret != ENOENT) {
dev_err(pcdev->dev,
"error: wrong number of pairsets. Should be 1 or 2, got %d (%pOF)\n",
ret, node);
ret = -EINVAL;
goto out;
}
of_node_get(node);
pi.np = node;
memcpy(&pcdev->pi[id], &pi, sizeof(pi));
}
of_node_put(pis);
return 0;
out:
pse_release_pis(pcdev);
of_node_put(node);
of_node_put(pis);
return ret;
}
static int pse_pi_is_enabled(struct regulator_dev *rdev)
{
struct pse_controller_dev *pcdev = rdev_get_drvdata(rdev);
const struct pse_controller_ops *ops;
int id, ret;
ops = pcdev->ops;
if (!ops->pi_is_enabled)
return -EOPNOTSUPP;
id = rdev_get_id(rdev);
mutex_lock(&pcdev->lock);
ret = ops->pi_is_enabled(pcdev, id);
mutex_unlock(&pcdev->lock);
return ret;
}
static int pse_pi_enable(struct regulator_dev *rdev)
{
struct pse_controller_dev *pcdev = rdev_get_drvdata(rdev);
const struct pse_controller_ops *ops;
int id, ret;
ops = pcdev->ops;
if (!ops->pi_enable)
return -EOPNOTSUPP;
id = rdev_get_id(rdev);
mutex_lock(&pcdev->lock);
ret = ops->pi_enable(pcdev, id);
if (!ret)
pcdev->pi[id].admin_state_enabled = 1;
mutex_unlock(&pcdev->lock);
return ret;
}
static int pse_pi_disable(struct regulator_dev *rdev)
{
struct pse_controller_dev *pcdev = rdev_get_drvdata(rdev);
const struct pse_controller_ops *ops;
int id, ret;
ops = pcdev->ops;
if (!ops->pi_disable)
return -EOPNOTSUPP;
id = rdev_get_id(rdev);
mutex_lock(&pcdev->lock);
ret = ops->pi_disable(pcdev, id);
if (!ret)
pcdev->pi[id].admin_state_enabled = 0;
mutex_unlock(&pcdev->lock);
return ret;
}
static int _pse_pi_get_voltage(struct regulator_dev *rdev)
{
struct pse_controller_dev *pcdev = rdev_get_drvdata(rdev);
const struct pse_controller_ops *ops;
int id;
ops = pcdev->ops;
if (!ops->pi_get_voltage)
return -EOPNOTSUPP;
id = rdev_get_id(rdev);
return ops->pi_get_voltage(pcdev, id);
}
static int pse_pi_get_voltage(struct regulator_dev *rdev)
{
struct pse_controller_dev *pcdev = rdev_get_drvdata(rdev);
int ret;
mutex_lock(&pcdev->lock);
ret = _pse_pi_get_voltage(rdev);
mutex_unlock(&pcdev->lock);
return ret;
}
static int _pse_ethtool_get_status(struct pse_controller_dev *pcdev,
int id,
struct netlink_ext_ack *extack,
struct pse_control_status *status);
static int pse_pi_get_current_limit(struct regulator_dev *rdev)
{
struct pse_controller_dev *pcdev = rdev_get_drvdata(rdev);
const struct pse_controller_ops *ops;
struct netlink_ext_ack extack = {};
struct pse_control_status st = {};
int id, uV, ret;
s64 tmp_64;
ops = pcdev->ops;
id = rdev_get_id(rdev);
mutex_lock(&pcdev->lock);
if (ops->pi_get_current_limit) {
ret = ops->pi_get_current_limit(pcdev, id);
goto out;
}
/* If pi_get_current_limit() callback not populated get voltage
* from pi_get_voltage() and power limit from ethtool_get_status()
* to calculate current limit.
*/
ret = _pse_pi_get_voltage(rdev);
if (!ret) {
dev_err(pcdev->dev, "Voltage null\n");
ret = -ERANGE;
goto out;
}
if (ret < 0)
goto out;
uV = ret;
ret = _pse_ethtool_get_status(pcdev, id, &extack, &st);
if (ret)
goto out;
if (!st.c33_avail_pw_limit) {
ret = -ENODATA;
goto out;
}
tmp_64 = st.c33_avail_pw_limit;
tmp_64 *= 1000000000ull;
/* uA = mW * 1000000000 / uV */
ret = DIV_ROUND_CLOSEST_ULL(tmp_64, uV);
out:
mutex_unlock(&pcdev->lock);
return ret;
}
static int pse_pi_set_current_limit(struct regulator_dev *rdev, int min_uA,
int max_uA)
{
struct pse_controller_dev *pcdev = rdev_get_drvdata(rdev);
const struct pse_controller_ops *ops;
int id, ret;
ops = pcdev->ops;
if (!ops->pi_set_current_limit)
return -EOPNOTSUPP;
id = rdev_get_id(rdev);
mutex_lock(&pcdev->lock);
ret = ops->pi_set_current_limit(pcdev, id, max_uA);
mutex_unlock(&pcdev->lock);
return ret;
}
static const struct regulator_ops pse_pi_ops = {
.is_enabled = pse_pi_is_enabled,
.enable = pse_pi_enable,
.disable = pse_pi_disable,
.get_voltage = pse_pi_get_voltage,
.get_current_limit = pse_pi_get_current_limit,
.set_current_limit = pse_pi_set_current_limit,
};
static int
devm_pse_pi_regulator_register(struct pse_controller_dev *pcdev,
char *name, int id)
{
struct regulator_init_data *rinit_data;
struct regulator_config rconfig = {0};
struct regulator_desc *rdesc;
struct regulator_dev *rdev;
rinit_data = devm_kzalloc(pcdev->dev, sizeof(*rinit_data),
GFP_KERNEL);
if (!rinit_data)
return -ENOMEM;
rdesc = devm_kzalloc(pcdev->dev, sizeof(*rdesc), GFP_KERNEL);
if (!rdesc)
return -ENOMEM;
/* Regulator descriptor id have to be the same as its associated
* PSE PI id for the well functioning of the PSE controls.
*/
rdesc->id = id;
rdesc->name = name;
rdesc->type = REGULATOR_VOLTAGE;
rdesc->ops = &pse_pi_ops;
rdesc->owner = pcdev->owner;
rinit_data->constraints.valid_ops_mask = REGULATOR_CHANGE_STATUS;
if (pcdev->ops->pi_set_current_limit) {
rinit_data->constraints.valid_ops_mask |=
REGULATOR_CHANGE_CURRENT;
rinit_data->constraints.max_uA = MAX_PI_CURRENT;
}
rinit_data->supply_regulator = "vpwr";
rconfig.dev = pcdev->dev;
rconfig.driver_data = pcdev;
rconfig.init_data = rinit_data;
rdev = devm_regulator_register(pcdev->dev, rdesc, &rconfig);
if (IS_ERR(rdev)) {
dev_err_probe(pcdev->dev, PTR_ERR(rdev),
"Failed to register regulator\n");
return PTR_ERR(rdev);
}
pcdev->pi[id].rdev = rdev;
return 0;
}
/**
* pse_controller_register - register a PSE controller device
* @pcdev: a pointer to the initialized PSE controller device
*
* Return: 0 on success and failure value on error
*/
int pse_controller_register(struct pse_controller_dev *pcdev)
{
size_t reg_name_len;
int ret, i;
mutex_init(&pcdev->lock);
INIT_LIST_HEAD(&pcdev->pse_control_head);
if (!pcdev->nr_lines)
pcdev->nr_lines = 1;
ret = of_load_pse_pis(pcdev);
if (ret)
return ret;
if (pcdev->ops->setup_pi_matrix) {
ret = pcdev->ops->setup_pi_matrix(pcdev);
if (ret)
return ret;
}
/* Each regulator name len is pcdev dev name + 7 char +
* int max digit number (10) + 1
*/
reg_name_len = strlen(dev_name(pcdev->dev)) + 18;
/* Register PI regulators */
for (i = 0; i < pcdev->nr_lines; i++) {
char *reg_name;
/* Do not register regulator for PIs not described */
if (!pcdev->no_of_pse_pi && !pcdev->pi[i].np)
continue;
reg_name = devm_kzalloc(pcdev->dev, reg_name_len, GFP_KERNEL);
if (!reg_name)
return -ENOMEM;
snprintf(reg_name, reg_name_len, "pse-%s_pi%d",
dev_name(pcdev->dev), i);
ret = devm_pse_pi_regulator_register(pcdev, reg_name, i);
if (ret)
return ret;
}
mutex_lock(&pse_list_mutex);
list_add(&pcdev->list, &pse_controller_list);
mutex_unlock(&pse_list_mutex);
return 0;
}
EXPORT_SYMBOL_GPL(pse_controller_register);
/**
* pse_controller_unregister - unregister a PSE controller device
* @pcdev: a pointer to the PSE controller device
*/
void pse_controller_unregister(struct pse_controller_dev *pcdev)
{
pse_release_pis(pcdev);
mutex_lock(&pse_list_mutex);
list_del(&pcdev->list);
mutex_unlock(&pse_list_mutex);
}
EXPORT_SYMBOL_GPL(pse_controller_unregister);
static void devm_pse_controller_release(struct device *dev, void *res)
{
pse_controller_unregister(*(struct pse_controller_dev **)res);
}
/**
* devm_pse_controller_register - resource managed pse_controller_register()
* @dev: device that is registering this PSE controller
* @pcdev: a pointer to the initialized PSE controller device
*
* Managed pse_controller_register(). For PSE controllers registered by
* this function, pse_controller_unregister() is automatically called on
* driver detach. See pse_controller_register() for more information.
*
* Return: 0 on success and failure value on error
*/
int devm_pse_controller_register(struct device *dev,
struct pse_controller_dev *pcdev)
{
struct pse_controller_dev **pcdevp;
int ret;
pcdevp = devres_alloc(devm_pse_controller_release, sizeof(*pcdevp),
GFP_KERNEL);
if (!pcdevp)
return -ENOMEM;
ret = pse_controller_register(pcdev);
if (ret) {
devres_free(pcdevp);
return ret;
}
*pcdevp = pcdev;
devres_add(dev, pcdevp);
return 0;
}
EXPORT_SYMBOL_GPL(devm_pse_controller_register);
/* PSE control section */
static void __pse_control_release(struct kref *kref)
{
struct pse_control *psec = container_of(kref, struct pse_control,
refcnt);
lockdep_assert_held(&pse_list_mutex);
if (psec->pcdev->pi[psec->id].admin_state_enabled)
regulator_disable(psec->ps);
devm_regulator_put(psec->ps);
module_put(psec->pcdev->owner);
list_del(&psec->list);
kfree(psec);
}
static void __pse_control_put_internal(struct pse_control *psec)
{
lockdep_assert_held(&pse_list_mutex);
kref_put(&psec->refcnt, __pse_control_release);
}
/**
* pse_control_put - free the PSE control
* @psec: PSE control pointer
*/
void pse_control_put(struct pse_control *psec)
{
if (IS_ERR_OR_NULL(psec))
return;
mutex_lock(&pse_list_mutex);
__pse_control_put_internal(psec);
mutex_unlock(&pse_list_mutex);
}
EXPORT_SYMBOL_GPL(pse_control_put);
static struct pse_control *
pse_control_get_internal(struct pse_controller_dev *pcdev, unsigned int index)
{
struct pse_control *psec;
int ret;
lockdep_assert_held(&pse_list_mutex);
list_for_each_entry(psec, &pcdev->pse_control_head, list) {
if (psec->id == index) {
kref_get(&psec->refcnt);
return psec;
}
}
psec = kzalloc(sizeof(*psec), GFP_KERNEL);
if (!psec)
return ERR_PTR(-ENOMEM);
if (!try_module_get(pcdev->owner)) {
ret = -ENODEV;
goto free_psec;
}
psec->ps = devm_regulator_get_exclusive(pcdev->dev,
rdev_get_name(pcdev->pi[index].rdev));
if (IS_ERR(psec->ps)) {
ret = PTR_ERR(psec->ps);
goto put_module;
}
ret = regulator_is_enabled(psec->ps);
if (ret < 0)
goto regulator_put;
pcdev->pi[index].admin_state_enabled = ret;
psec->pcdev = pcdev;
list_add(&psec->list, &pcdev->pse_control_head);
psec->id = index;
kref_init(&psec->refcnt);
return psec;
regulator_put:
devm_regulator_put(psec->ps);
put_module:
module_put(pcdev->owner);
free_psec:
kfree(psec);
return ERR_PTR(ret);
}
/**
* of_pse_match_pi - Find the PSE PI id matching the device node phandle
* @pcdev: a pointer to the PSE controller device
* @np: a pointer to the device node
*
* Return: id of the PSE PI, -EINVAL if not found
*/
static int of_pse_match_pi(struct pse_controller_dev *pcdev,
struct device_node *np)
{
int i;
for (i = 0; i <= pcdev->nr_lines; i++) {
if (pcdev->pi[i].np == np)
return i;
}
return -EINVAL;
}
/**
* psec_id_xlate - translate pse_spec to the PSE line number according
* to the number of pse-cells in case of no pse_pi node
* @pcdev: a pointer to the PSE controller device
* @pse_spec: PSE line specifier as found in the device tree
*
* Return: 0 if #pse-cells = <0>. Return PSE line number otherwise.
*/
static int psec_id_xlate(struct pse_controller_dev *pcdev,
const struct of_phandle_args *pse_spec)
{
if (!pcdev->of_pse_n_cells)
return 0;
if (pcdev->of_pse_n_cells > 1 ||
pse_spec->args[0] >= pcdev->nr_lines)
return -EINVAL;
return pse_spec->args[0];
}
struct pse_control *of_pse_control_get(struct device_node *node)
{
struct pse_controller_dev *r, *pcdev;
struct of_phandle_args args;
struct pse_control *psec;
int psec_id;
int ret;
if (!node)
return ERR_PTR(-EINVAL);
ret = of_parse_phandle_with_args(node, "pses", "#pse-cells", 0, &args);
if (ret)
return ERR_PTR(ret);
mutex_lock(&pse_list_mutex);
pcdev = NULL;
list_for_each_entry(r, &pse_controller_list, list) {
if (!r->no_of_pse_pi) {
ret = of_pse_match_pi(r, args.np);
if (ret >= 0) {
pcdev = r;
psec_id = ret;
break;
}
} else if (args.np == r->dev->of_node) {
pcdev = r;
break;
}
}
if (!pcdev) {
psec = ERR_PTR(-EPROBE_DEFER);
goto out;
}
if (WARN_ON(args.args_count != pcdev->of_pse_n_cells)) {
psec = ERR_PTR(-EINVAL);
goto out;
}
if (pcdev->no_of_pse_pi) {
psec_id = psec_id_xlate(pcdev, &args);
if (psec_id < 0) {
psec = ERR_PTR(psec_id);
goto out;
}
}
/* pse_list_mutex also protects the pcdev's pse_control list */
psec = pse_control_get_internal(pcdev, psec_id);
out:
mutex_unlock(&pse_list_mutex);
of_node_put(args.np);
return psec;
}
EXPORT_SYMBOL_GPL(of_pse_control_get);
ethtool: add interface to interact with Ethernet Power Equipment Add interface to support Power Sourcing Equipment. At current step it provides generic way to address all variants of PSE devices as defined in IEEE 802.3-2018 but support only objects specified for IEEE 802.3-2018 104.4 PoDL Power Sourcing Equipment (PSE). Currently supported and mandatory objects are: IEEE 802.3-2018 30.15.1.1.3 aPoDLPSEPowerDetectionStatus IEEE 802.3-2018 30.15.1.1.2 aPoDLPSEAdminState IEEE 802.3-2018 30.15.1.2.1 acPoDLPSEAdminControl This is minimal interface needed to control PSE on each separate ethernet port but it provides not all mandatory objects specified in IEEE 802.3-2018. Since "PoDL PSE" and "PSE" have similar names, but some different values I decide to not merge them and keep separate naming schema. This should allow as to be as close to IEEE 802.3 spec as possible and avoid name conflicts in the future. This implementation is connected to PHYs instead of MACs because PSE auto classification can potentially interfere with PHY auto negotiation. So, may be some extra PHY related initialization will be needed. With WIP version of ethtools interaction with PSE capable link looks as following: $ ip l ... 5: t1l1@eth0: <BROADCAST,MULTICAST> .. ... $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: disabled PoDL PSE Power Detection Status: disabled $ ethtool --set-pse t1l1 podl-pse-admin-control enable $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: enabled PoDL PSE Power Detection Status: delivering power Signed-off-by: kernel test robot <lkp@intel.com> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Bagas Sanjaya <bagasdotme@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-10-03 06:52:00 +00:00
static int _pse_ethtool_get_status(struct pse_controller_dev *pcdev,
int id,
struct netlink_ext_ack *extack,
struct pse_control_status *status)
{
const struct pse_controller_ops *ops;
ops = pcdev->ops;
if (!ops->ethtool_get_status) {
NL_SET_ERR_MSG(extack,
"PSE driver does not support status report");
return -EOPNOTSUPP;
}
return ops->ethtool_get_status(pcdev, id, extack, status);
}
ethtool: add interface to interact with Ethernet Power Equipment Add interface to support Power Sourcing Equipment. At current step it provides generic way to address all variants of PSE devices as defined in IEEE 802.3-2018 but support only objects specified for IEEE 802.3-2018 104.4 PoDL Power Sourcing Equipment (PSE). Currently supported and mandatory objects are: IEEE 802.3-2018 30.15.1.1.3 aPoDLPSEPowerDetectionStatus IEEE 802.3-2018 30.15.1.1.2 aPoDLPSEAdminState IEEE 802.3-2018 30.15.1.2.1 acPoDLPSEAdminControl This is minimal interface needed to control PSE on each separate ethernet port but it provides not all mandatory objects specified in IEEE 802.3-2018. Since "PoDL PSE" and "PSE" have similar names, but some different values I decide to not merge them and keep separate naming schema. This should allow as to be as close to IEEE 802.3 spec as possible and avoid name conflicts in the future. This implementation is connected to PHYs instead of MACs because PSE auto classification can potentially interfere with PHY auto negotiation. So, may be some extra PHY related initialization will be needed. With WIP version of ethtools interaction with PSE capable link looks as following: $ ip l ... 5: t1l1@eth0: <BROADCAST,MULTICAST> .. ... $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: disabled PoDL PSE Power Detection Status: disabled $ ethtool --set-pse t1l1 podl-pse-admin-control enable $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: enabled PoDL PSE Power Detection Status: delivering power Signed-off-by: kernel test robot <lkp@intel.com> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Bagas Sanjaya <bagasdotme@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-10-03 06:52:00 +00:00
/**
* pse_ethtool_get_status - get status of PSE control
* @psec: PSE control pointer
* @extack: extack for reporting useful error messages
* @status: struct to store PSE status
*
* Return: 0 on success and failure value on error
ethtool: add interface to interact with Ethernet Power Equipment Add interface to support Power Sourcing Equipment. At current step it provides generic way to address all variants of PSE devices as defined in IEEE 802.3-2018 but support only objects specified for IEEE 802.3-2018 104.4 PoDL Power Sourcing Equipment (PSE). Currently supported and mandatory objects are: IEEE 802.3-2018 30.15.1.1.3 aPoDLPSEPowerDetectionStatus IEEE 802.3-2018 30.15.1.1.2 aPoDLPSEAdminState IEEE 802.3-2018 30.15.1.2.1 acPoDLPSEAdminControl This is minimal interface needed to control PSE on each separate ethernet port but it provides not all mandatory objects specified in IEEE 802.3-2018. Since "PoDL PSE" and "PSE" have similar names, but some different values I decide to not merge them and keep separate naming schema. This should allow as to be as close to IEEE 802.3 spec as possible and avoid name conflicts in the future. This implementation is connected to PHYs instead of MACs because PSE auto classification can potentially interfere with PHY auto negotiation. So, may be some extra PHY related initialization will be needed. With WIP version of ethtools interaction with PSE capable link looks as following: $ ip l ... 5: t1l1@eth0: <BROADCAST,MULTICAST> .. ... $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: disabled PoDL PSE Power Detection Status: disabled $ ethtool --set-pse t1l1 podl-pse-admin-control enable $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: enabled PoDL PSE Power Detection Status: delivering power Signed-off-by: kernel test robot <lkp@intel.com> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Bagas Sanjaya <bagasdotme@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-10-03 06:52:00 +00:00
*/
int pse_ethtool_get_status(struct pse_control *psec,
struct netlink_ext_ack *extack,
struct pse_control_status *status)
{
int err;
mutex_lock(&psec->pcdev->lock);
err = _pse_ethtool_get_status(psec->pcdev, psec->id, extack, status);
ethtool: add interface to interact with Ethernet Power Equipment Add interface to support Power Sourcing Equipment. At current step it provides generic way to address all variants of PSE devices as defined in IEEE 802.3-2018 but support only objects specified for IEEE 802.3-2018 104.4 PoDL Power Sourcing Equipment (PSE). Currently supported and mandatory objects are: IEEE 802.3-2018 30.15.1.1.3 aPoDLPSEPowerDetectionStatus IEEE 802.3-2018 30.15.1.1.2 aPoDLPSEAdminState IEEE 802.3-2018 30.15.1.2.1 acPoDLPSEAdminControl This is minimal interface needed to control PSE on each separate ethernet port but it provides not all mandatory objects specified in IEEE 802.3-2018. Since "PoDL PSE" and "PSE" have similar names, but some different values I decide to not merge them and keep separate naming schema. This should allow as to be as close to IEEE 802.3 spec as possible and avoid name conflicts in the future. This implementation is connected to PHYs instead of MACs because PSE auto classification can potentially interfere with PHY auto negotiation. So, may be some extra PHY related initialization will be needed. With WIP version of ethtools interaction with PSE capable link looks as following: $ ip l ... 5: t1l1@eth0: <BROADCAST,MULTICAST> .. ... $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: disabled PoDL PSE Power Detection Status: disabled $ ethtool --set-pse t1l1 podl-pse-admin-control enable $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: enabled PoDL PSE Power Detection Status: delivering power Signed-off-by: kernel test robot <lkp@intel.com> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Bagas Sanjaya <bagasdotme@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-10-03 06:52:00 +00:00
mutex_unlock(&psec->pcdev->lock);
return err;
}
EXPORT_SYMBOL_GPL(pse_ethtool_get_status);
static int pse_ethtool_c33_set_config(struct pse_control *psec,
const struct pse_control_config *config)
{
int err = 0;
/* Look at admin_state_enabled status to not call regulator_enable
* or regulator_disable twice creating a regulator counter mismatch
*/
switch (config->c33_admin_control) {
case ETHTOOL_C33_PSE_ADMIN_STATE_ENABLED:
if (!psec->pcdev->pi[psec->id].admin_state_enabled)
err = regulator_enable(psec->ps);
break;
case ETHTOOL_C33_PSE_ADMIN_STATE_DISABLED:
if (psec->pcdev->pi[psec->id].admin_state_enabled)
err = regulator_disable(psec->ps);
break;
default:
err = -EOPNOTSUPP;
}
return err;
}
static int pse_ethtool_podl_set_config(struct pse_control *psec,
const struct pse_control_config *config)
{
int err = 0;
/* Look at admin_state_enabled status to not call regulator_enable
* or regulator_disable twice creating a regulator counter mismatch
*/
switch (config->podl_admin_control) {
case ETHTOOL_PODL_PSE_ADMIN_STATE_ENABLED:
if (!psec->pcdev->pi[psec->id].admin_state_enabled)
err = regulator_enable(psec->ps);
break;
case ETHTOOL_PODL_PSE_ADMIN_STATE_DISABLED:
if (psec->pcdev->pi[psec->id].admin_state_enabled)
err = regulator_disable(psec->ps);
break;
default:
err = -EOPNOTSUPP;
}
return err;
}
ethtool: add interface to interact with Ethernet Power Equipment Add interface to support Power Sourcing Equipment. At current step it provides generic way to address all variants of PSE devices as defined in IEEE 802.3-2018 but support only objects specified for IEEE 802.3-2018 104.4 PoDL Power Sourcing Equipment (PSE). Currently supported and mandatory objects are: IEEE 802.3-2018 30.15.1.1.3 aPoDLPSEPowerDetectionStatus IEEE 802.3-2018 30.15.1.1.2 aPoDLPSEAdminState IEEE 802.3-2018 30.15.1.2.1 acPoDLPSEAdminControl This is minimal interface needed to control PSE on each separate ethernet port but it provides not all mandatory objects specified in IEEE 802.3-2018. Since "PoDL PSE" and "PSE" have similar names, but some different values I decide to not merge them and keep separate naming schema. This should allow as to be as close to IEEE 802.3 spec as possible and avoid name conflicts in the future. This implementation is connected to PHYs instead of MACs because PSE auto classification can potentially interfere with PHY auto negotiation. So, may be some extra PHY related initialization will be needed. With WIP version of ethtools interaction with PSE capable link looks as following: $ ip l ... 5: t1l1@eth0: <BROADCAST,MULTICAST> .. ... $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: disabled PoDL PSE Power Detection Status: disabled $ ethtool --set-pse t1l1 podl-pse-admin-control enable $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: enabled PoDL PSE Power Detection Status: delivering power Signed-off-by: kernel test robot <lkp@intel.com> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Bagas Sanjaya <bagasdotme@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-10-03 06:52:00 +00:00
/**
* pse_ethtool_set_config - set PSE control configuration
* @psec: PSE control pointer
* @extack: extack for reporting useful error messages
* @config: Configuration of the test to run
*
* Return: 0 on success and failure value on error
ethtool: add interface to interact with Ethernet Power Equipment Add interface to support Power Sourcing Equipment. At current step it provides generic way to address all variants of PSE devices as defined in IEEE 802.3-2018 but support only objects specified for IEEE 802.3-2018 104.4 PoDL Power Sourcing Equipment (PSE). Currently supported and mandatory objects are: IEEE 802.3-2018 30.15.1.1.3 aPoDLPSEPowerDetectionStatus IEEE 802.3-2018 30.15.1.1.2 aPoDLPSEAdminState IEEE 802.3-2018 30.15.1.2.1 acPoDLPSEAdminControl This is minimal interface needed to control PSE on each separate ethernet port but it provides not all mandatory objects specified in IEEE 802.3-2018. Since "PoDL PSE" and "PSE" have similar names, but some different values I decide to not merge them and keep separate naming schema. This should allow as to be as close to IEEE 802.3 spec as possible and avoid name conflicts in the future. This implementation is connected to PHYs instead of MACs because PSE auto classification can potentially interfere with PHY auto negotiation. So, may be some extra PHY related initialization will be needed. With WIP version of ethtools interaction with PSE capable link looks as following: $ ip l ... 5: t1l1@eth0: <BROADCAST,MULTICAST> .. ... $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: disabled PoDL PSE Power Detection Status: disabled $ ethtool --set-pse t1l1 podl-pse-admin-control enable $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: enabled PoDL PSE Power Detection Status: delivering power Signed-off-by: kernel test robot <lkp@intel.com> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Bagas Sanjaya <bagasdotme@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-10-03 06:52:00 +00:00
*/
int pse_ethtool_set_config(struct pse_control *psec,
struct netlink_ext_ack *extack,
const struct pse_control_config *config)
{
int err = 0;
ethtool: add interface to interact with Ethernet Power Equipment Add interface to support Power Sourcing Equipment. At current step it provides generic way to address all variants of PSE devices as defined in IEEE 802.3-2018 but support only objects specified for IEEE 802.3-2018 104.4 PoDL Power Sourcing Equipment (PSE). Currently supported and mandatory objects are: IEEE 802.3-2018 30.15.1.1.3 aPoDLPSEPowerDetectionStatus IEEE 802.3-2018 30.15.1.1.2 aPoDLPSEAdminState IEEE 802.3-2018 30.15.1.2.1 acPoDLPSEAdminControl This is minimal interface needed to control PSE on each separate ethernet port but it provides not all mandatory objects specified in IEEE 802.3-2018. Since "PoDL PSE" and "PSE" have similar names, but some different values I decide to not merge them and keep separate naming schema. This should allow as to be as close to IEEE 802.3 spec as possible and avoid name conflicts in the future. This implementation is connected to PHYs instead of MACs because PSE auto classification can potentially interfere with PHY auto negotiation. So, may be some extra PHY related initialization will be needed. With WIP version of ethtools interaction with PSE capable link looks as following: $ ip l ... 5: t1l1@eth0: <BROADCAST,MULTICAST> .. ... $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: disabled PoDL PSE Power Detection Status: disabled $ ethtool --set-pse t1l1 podl-pse-admin-control enable $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: enabled PoDL PSE Power Detection Status: delivering power Signed-off-by: kernel test robot <lkp@intel.com> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Bagas Sanjaya <bagasdotme@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-10-03 06:52:00 +00:00
if (pse_has_c33(psec) && config->c33_admin_control) {
err = pse_ethtool_c33_set_config(psec, config);
if (err)
return err;
ethtool: add interface to interact with Ethernet Power Equipment Add interface to support Power Sourcing Equipment. At current step it provides generic way to address all variants of PSE devices as defined in IEEE 802.3-2018 but support only objects specified for IEEE 802.3-2018 104.4 PoDL Power Sourcing Equipment (PSE). Currently supported and mandatory objects are: IEEE 802.3-2018 30.15.1.1.3 aPoDLPSEPowerDetectionStatus IEEE 802.3-2018 30.15.1.1.2 aPoDLPSEAdminState IEEE 802.3-2018 30.15.1.2.1 acPoDLPSEAdminControl This is minimal interface needed to control PSE on each separate ethernet port but it provides not all mandatory objects specified in IEEE 802.3-2018. Since "PoDL PSE" and "PSE" have similar names, but some different values I decide to not merge them and keep separate naming schema. This should allow as to be as close to IEEE 802.3 spec as possible and avoid name conflicts in the future. This implementation is connected to PHYs instead of MACs because PSE auto classification can potentially interfere with PHY auto negotiation. So, may be some extra PHY related initialization will be needed. With WIP version of ethtools interaction with PSE capable link looks as following: $ ip l ... 5: t1l1@eth0: <BROADCAST,MULTICAST> .. ... $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: disabled PoDL PSE Power Detection Status: disabled $ ethtool --set-pse t1l1 podl-pse-admin-control enable $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: enabled PoDL PSE Power Detection Status: delivering power Signed-off-by: kernel test robot <lkp@intel.com> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Bagas Sanjaya <bagasdotme@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-10-03 06:52:00 +00:00
}
if (pse_has_podl(psec) && config->podl_admin_control)
err = pse_ethtool_podl_set_config(psec, config);
ethtool: add interface to interact with Ethernet Power Equipment Add interface to support Power Sourcing Equipment. At current step it provides generic way to address all variants of PSE devices as defined in IEEE 802.3-2018 but support only objects specified for IEEE 802.3-2018 104.4 PoDL Power Sourcing Equipment (PSE). Currently supported and mandatory objects are: IEEE 802.3-2018 30.15.1.1.3 aPoDLPSEPowerDetectionStatus IEEE 802.3-2018 30.15.1.1.2 aPoDLPSEAdminState IEEE 802.3-2018 30.15.1.2.1 acPoDLPSEAdminControl This is minimal interface needed to control PSE on each separate ethernet port but it provides not all mandatory objects specified in IEEE 802.3-2018. Since "PoDL PSE" and "PSE" have similar names, but some different values I decide to not merge them and keep separate naming schema. This should allow as to be as close to IEEE 802.3 spec as possible and avoid name conflicts in the future. This implementation is connected to PHYs instead of MACs because PSE auto classification can potentially interfere with PHY auto negotiation. So, may be some extra PHY related initialization will be needed. With WIP version of ethtools interaction with PSE capable link looks as following: $ ip l ... 5: t1l1@eth0: <BROADCAST,MULTICAST> .. ... $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: disabled PoDL PSE Power Detection Status: disabled $ ethtool --set-pse t1l1 podl-pse-admin-control enable $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: enabled PoDL PSE Power Detection Status: delivering power Signed-off-by: kernel test robot <lkp@intel.com> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Bagas Sanjaya <bagasdotme@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-10-03 06:52:00 +00:00
return err;
}
EXPORT_SYMBOL_GPL(pse_ethtool_set_config);
/**
* pse_ethtool_set_pw_limit - set PSE control power limit
* @psec: PSE control pointer
* @extack: extack for reporting useful error messages
* @pw_limit: power limit value in mW
*
* Return: 0 on success and failure value on error
*/
int pse_ethtool_set_pw_limit(struct pse_control *psec,
struct netlink_ext_ack *extack,
const unsigned int pw_limit)
{
int uV, uA, ret;
s64 tmp_64;
ret = regulator_get_voltage(psec->ps);
if (!ret) {
NL_SET_ERR_MSG(extack,
"Can't calculate the current, PSE voltage read is 0");
return -ERANGE;
}
if (ret < 0) {
NL_SET_ERR_MSG(extack,
"Error reading PSE voltage");
return ret;
}
uV = ret;
tmp_64 = pw_limit;
tmp_64 *= 1000000000ull;
/* uA = mW * 1000000000 / uV */
uA = DIV_ROUND_CLOSEST_ULL(tmp_64, uV);
return regulator_set_current_limit(psec->ps, 0, uA);
}
EXPORT_SYMBOL_GPL(pse_ethtool_set_pw_limit);
bool pse_has_podl(struct pse_control *psec)
{
return psec->pcdev->types & ETHTOOL_PSE_PODL;
}
EXPORT_SYMBOL_GPL(pse_has_podl);
bool pse_has_c33(struct pse_control *psec)
{
return psec->pcdev->types & ETHTOOL_PSE_C33;
}
EXPORT_SYMBOL_GPL(pse_has_c33);