[ Upstream commit 25a6e135569b3901452e4863c94560df7c11c492 ]
MS-SMB2 specification describes setting ->DeviceType to FILE_DEVICE_DISK
or FILE_DEVICE_CD_ROM. Set FILE_DEVICE_DISK instead of super magic in
FS_DEVICE_INFORMATION. And Set FILE_READ_ONLY_DEVICE for read-only share.
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1762dc01fc78ef5f19693e9317eae7491c6c7e1b ]
On the OMAPL138, the SPI reference clock is provided by the Power and
Sleep Controller (PSC). The PSC's datasheet says that 'some peripherals
have special programming requirements and additional recommended steps
you must take before you can invoke the PSC module state transition'. I
didn't find more details in documentation but it appears that PSC needs
the SPI to clear the POWERDOWN bit before disabling the clock. Indeed,
when this bit is set, the PSC gets stuck in transitions from enable to
disable state.
Clear the POWERDOWN bit when releasing driver's resources
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20240624071745.17409-1-bastien.curutchet@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce1dac560a74220f2e53845ec0723b562288aed4 ]
While in commit 2dd33f9cec90 ("spi: imx: support DMA for imx35") it was
claimed that DMA works on i.MX25, i.MX31 and i.MX35 the respective
device trees don't add DMA channels. The Reference manuals of i.MX31 and
i.MX25 also don't mention the CSPI core being DMA capable. (I didn't
check the others.)
Since commit e267a5b3ec59 ("spi: spi-imx: Use dev_err_probe for failed
DMA channel requests") this results in an error message
spi_imx 43fa4000.spi: error -ENODEV: can't get the TX DMA channel!
during boot. However that isn't fatal and the driver gets loaded just
fine, just without using DMA.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://patch.msgid.link/20240508095610.2146640-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 393da6cbb2ff89aadc47683a85269f913aa1c139 ]
ftrace_graph_ret_addr() takes an `idx` integer pointer that is used to
optimize the stack unwinding. Pass it a valid pointer to utilize the
optimizations that might be available in the future.
The commit is making riscv's usage of ftrace_graph_ret_addr() match
x86_64.
Signed-off-by: Puranjay Mohan <puranjay@kernel.org>
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Link: https://lore.kernel.org/r/20240618145820.62112-1-puranjay@kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7dd646cf745c34d31e7ed2a52265e9ca8308f58f ]
Currently, we stop all the counters while a new cpu is brought online.
However, the hpmevent to counter mappings are not reset. The firmware may
have some stale encoding in their mapping structure which may lead to
undesirable results. We have not encountered such scenario though.
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Link: https://lore.kernel.org/r/20240628-misc_perf_fixes-v4-2-e01cfddcf035@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ec17ce716bdaf680288ce680b4621b52483cc96 ]
The WIPHY_FLAG_SUPPORTS_EXT_KEK_KCK should be set based on the
WOWLAN_KEK_KCK_MATERIAL command version. Currently, the command
version in the firmware has advanced to 4, which prevents the
flag from being set correctly, fix that.
Signed-off-by: Daniel Gabay <daniel.gabay@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240703064026.a0f162108575.If1a9785727d2a1b0197a396680965df1b53d4096@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 391b59b045004d5b985d033263ccba3e941a7740 ]
Jan reported that 'cd ..' may take a long time in deep directory
hierarchies under a bind-mount. If concurrent renames happen it is
possible to livelock in is_subdir() because it will keep retrying.
Change is_subdir() from simply retrying over and over to retry once and
then acquire the rename lock to handle deep ancestor chains better. The
list of alternatives to this approach were less then pleasant. Change
the scope of rcu lock to cover the whole walk while at it.
A big thanks to Jan and Linus. Both Jan and Linus had proposed
effectively the same thing just that one version ended up being slightly
more elegant.
Reported-by: Jan Kara <jack@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9da45c88e124f13a3c4d480b89b298e007fbb9e4 ]
In the ref-verify tool, when processing the inline references of an extent
item, we may end up returning with uninitialized return value, because:
1) The 'ret' variable is not initialized if there are no inline extent
references ('ptr' == 'end' before the while loop starts);
2) If we find an extent owner inline reference we don't initialize 'ret'.
So fix these cases by initializing 'ret' to 0 when declaring the variable
and set it to -EINVAL if we find an extent owner inline references and
simple quotas are not enabled (as well as print an error message).
Reported-by: Mirsad Todorovac <mtodorovac69@gmail.com>
Link: https://lore.kernel.org/linux-btrfs/59b40ebe-c824-457d-8b24-0bbca69d472b@gmail.com/
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6fb15dcbcf4f212930350eaee174bb60ed40a536 ]
The call to radeon_vm_clear_freed might clear bo_va->bo, so
we have to check it before dereferencing it.
Signed-off-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ad4b4a2f6357c45fbe444ead1a929a0b4017d03 ]
[Why]
Potential out of bounds access in dml2_calculate_rq_and_dlg_params()
because the value of out_lowest_state_idx used as an index for FCLKChangeSupport
array can be greater than 1.
[How]
Currently dml2 core specifies identical values for all FCLKChangeSupport
elements. Always use index 0 in the condition to avoid out of bounds access.
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ef1548aeaa8858e7aee2152bf95cc71cdcd6dff ]
[Why]
Some of the panels does not have the refresh rate range info
in base EDID and only have the refresh rate range info in
DisplayID block.
It will cause the max/min freesync refresh rate set to 0.
[How]
Try to parse the refresh rate range info from DisplayID if the
max/min refresh rate is 0.
Reviewed-by: Sun peng Li <sunpeng.li@amd.com>
Signed-off-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 074b3a886713f69d98d30bb348b1e4cb3ce52b22 ]
[Description]
We need to ensure to take into account cursor prefetch BW in
mode support or we may pass ModeQuery but fail an actual flip
which will cause a hang. Flip may fail because the cursor_pre_bw
is populated during mode programming (and mode programming is
never called prior to ModeQuery).
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Reviewed-by: Nevenko Stupar <nevenko.stupar@amd.com>
Signed-off-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 74ad26b36d303ac233eccadc5c3a8d7ee4709f31 ]
[Why]
We only enable the VRR while monitor usable refresh rate range
is greater than 10 Hz.
But we did not check the range in DRM_EDID_FEATURE_CONTINUOUS_FREQ
case.
[How]
Add a refresh rate range check before set the freesync_capable flag
in DRM_EDID_FEATURE_CONTINUOUS_FREQ case.
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b32b063be1001e322c5f6e01f2a649636947851 ]
Sometimes, the on-disk metadata might be invalid due to user
interrupts, storage failures, or other unknown causes.
In that case, z_erofs_map_blocks_iter() may still return a valid
m_llen while other fields remain invalid (e.g., m_plen can be 0).
Due to the return value of z_erofs_scan_folio() in some path will
be ignored on purpose, the following z_erofs_scan_folio() could
then use the invalid value by accident.
Let's reset m_llen to 0 to prevent this.
Link: https://lore.kernel.org/r/20240629185743.2819229-1-hsiangkao@linux.alibaba.com
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 89e856e124f9ae548572c56b1b70c2255705f8fe ]
The problem occurs between the system call to close the sock and hci_rx_work,
where the former releases the sock and the latter accesses it without lock protection.
CPU0 CPU1
---- ----
sock_close hci_rx_work
l2cap_sock_release hci_acldata_packet
l2cap_sock_kill l2cap_recv_frame
sk_free l2cap_conless_channel
l2cap_sock_recv_cb
If hci_rx_work processes the data that needs to be received before the sock is
closed, then everything is normal; Otherwise, the work thread may access the
released sock when receiving data.
Add a chan mutex in the rx callback of the sock to achieve synchronization between
the sock release and recv cb.
Sock is dead, so set chan data to NULL, avoid others use invalid sock pointer.
Reported-and-tested-by: syzbot+b7f6f8c9303466e16c8a@syzkaller.appspotmail.com
Signed-off-by: Edward Adam Davis <eadavis@qq.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4183a7be77009fc31c5760429fe095f163bf96a9 ]
This sets the default power save mode setting to enabled.
The power save feature is now stable and stress test issues, such as the
TX timeout error, have been resolved.
commit c7ee0bc8db32 ("Bluetooth: btnxpuart: Resolve TX timeout error in
power save stress test")
With this setting, the driver will send the vendor command to FW at
startup, to enable power save feature.
User can disable this feature using the following vendor command:
hcitool cmd 3f 23 03 00 00 (HCI_NXP_AUTO_SLEEP_MODE)
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d151a103775dd9645c78c97f77d6e2a5298d913 ]
syzbot is reporting that calling hci_release_dev() from hci_error_reset()
due to hci_dev_put() from hci_error_reset() can cause deadlock at
destroy_workqueue(), for hci_error_reset() is called from
hdev->req_workqueue which destroy_workqueue() needs to flush.
We need to make sure that hdev->{rx_work,cmd_work,tx_work} which are
queued into hdev->workqueue and hdev->{power_on,error_reset} which are
queued into hdev->req_workqueue are no longer running by the moment
destroy_workqueue(hdev->workqueue);
destroy_workqueue(hdev->req_workqueue);
are called from hci_release_dev().
Call cancel_work_sync() on these work items from hci_unregister_dev()
as soon as hdev->list is removed from hci_dev_list.
Reported-by: syzbot <syzbot+da0a9c9721e36db712e8@syzkaller.appspotmail.com>
Closes: https://syzkaller.appspot.com/bug?extid=da0a9c9721e36db712e8
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e0556255a53d6d3d406a28362dffd972018a997c ]
The 'missing-field-initializers' warning was reported
when building with W=2.
This patch use designated initializers for
'struct ffa_send_direct_data' to suppress the warning
and clarify the initialization intent.
Signed-off-by: ming-jen.chang <ming-jen.chang@mediatek.com>
Signed-off-by: Mark-PK Tsai <mark-pk.tsai@mediatek.com>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab2068a6fb84751836a84c26ca72b3beb349619d ]
The expander phy will be treated as broadcast flutter in the next
revalidation after the exp-attached end device probe failed, as follows:
[78779.654026] sas: broadcast received: 0
[78779.654037] sas: REVALIDATING DOMAIN on port 0, pid:10
[78779.654680] sas: ex 500e004aaaaaaa1f phy05 change count has changed
[78779.662977] sas: ex 500e004aaaaaaa1f phy05 originated BROADCAST(CHANGE)
[78779.662986] sas: ex 500e004aaaaaaa1f phy05 new device attached
[78779.663079] sas: ex 500e004aaaaaaa1f phy05:U:8 attached: 500e004aaaaaaa05 (stp)
[78779.693542] hisi_sas_v3_hw 0000:b4:02.0: dev[16:5] found
[78779.701155] sas: done REVALIDATING DOMAIN on port 0, pid:10, res 0x0
[78779.707864] sas: Enter sas_scsi_recover_host busy: 0 failed: 0
...
[78835.161307] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[78835.171344] sas: sas_probe_sata: for exp-attached device 500e004aaaaaaa05 returned -19
[78835.180879] hisi_sas_v3_hw 0000:b4:02.0: dev[16:5] is gone
[78835.187487] sas: broadcast received: 0
[78835.187504] sas: REVALIDATING DOMAIN on port 0, pid:10
[78835.188263] sas: ex 500e004aaaaaaa1f phy05 change count has changed
[78835.195870] sas: ex 500e004aaaaaaa1f phy05 originated BROADCAST(CHANGE)
[78835.195875] sas: ex 500e004aaaaaaa1f rediscovering phy05
[78835.196022] sas: ex 500e004aaaaaaa1f phy05:U:A attached: 500e004aaaaaaa05 (stp)
[78835.196026] sas: ex 500e004aaaaaaa1f phy05 broadcast flutter
[78835.197615] sas: done REVALIDATING DOMAIN on port 0, pid:10, res 0x0
The cause of the problem is that the related ex_phy's attached_sas_addr was
not cleared after the end device probe failed, so reset it.
Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Link: https://lore.kernel.org/r/20240619091742.25465-1-yangxingui@huawei.com
Reviewed-by: John Garry <john.g.garry@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a1216e62d039bf63a539bbe718536ec789a853dd ]
If a PCI device is removed during eeh_pe_report_edev(), edev->pdev
will change and can cause a crash, hold the PCI rescan/remove lock
while taking a copy of edev->pdev->bus.
Signed-off-by: Ganesh Goudar <ganeshgr@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20240617140240.580453-1-ganeshgr@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ba8425678af422da37b6c9b50e9ce66f0f55cae ]
Since the CONFIG_CTL register is only 32 bits wide in the Stromer
and Stromer Plus PLLs , the 'config_ctl_hi_val' values from the
IPQ5018 and IPQ5332 configurations are not used so remove those.
No functional changes.
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Reviewed-by: Kathiravan Thirumoorthy <quic_kathirav@quicinc.com>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240509-stromer-config-ctl-v1-1-6034e17b28d5@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63b47f026cc841bd3d3438dd6fccbc394dfead87 ]
The Vivobook S 16X IPS needs a quirks-table entry for the internal microphone to function properly.
Signed-off-by: Vyacheslav Frantsishko <itmymaill@gmail.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://patch.msgid.link/20240626070334.45633-1-itmymaill@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c223376b3019a00a0241faea0bc8c966738d1cc5 ]
[Why]
SMU firmware has not supported MALL PG.
[How]
Disable MALL PG and make it always on until SMU firmware is ready.
Signed-off-by: Li Ma <li.ma@amd.com>
Reviewed-by: Tim Huang <Tim.Huang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a7db25aad8ce6512b366d2ce1d0e60bac00a09d ]
When dmaengine supports pause function, in suspend state,
dmaengine_pause() is called instead of dmaengine_terminate_async(),
In end of playback stream, the runtime->state will go to
SNDRV_PCM_STATE_DRAINING, if system suspend & resume happen
at this time, application will not resume playback stream, the
stream will be closed directly, the dmaengine_terminate_async()
will not be called before the dmaengine_synchronize(), which
violates the call sequence for dmaengine_synchronize().
This behavior also happens for capture streams, but there is no
SNDRV_PCM_STATE_DRAINING state for capture. So use
dmaengine_tx_status() to check the DMA status if the status is
DMA_PAUSED, then call dmaengine_terminate_async() to terminate
dmaengine before dmaengine_synchronize().
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://patch.msgid.link/1718851218-27803-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0983d288caf984de0202c66641577b739caad561 ]
Below is a summary of how the driver stores a reference to an skb during
transmit:
tx_buff[free_map[consumer_index]]->skb = new_skb;
free_map[consumer_index] = IBMVNIC_INVALID_MAP;
consumer_index ++;
Where variable data looks like this:
free_map == [4, IBMVNIC_INVALID_MAP, IBMVNIC_INVALID_MAP, 0, 3]
consumer_index^
tx_buff == [skb=null, skb=<ptr>, skb=<ptr>, skb=null, skb=null]
The driver has checks to ensure that free_map[consumer_index] pointed to
a valid index but there was no check to ensure that this index pointed
to an unused/null skb address. So, if, by some chance, our free_map and
tx_buff lists become out of sync then we were previously risking an
skb memory leak. This could then cause tcp congestion control to stop
sending packets, eventually leading to ETIMEDOUT.
Therefore, add a conditional to ensure that the skb address is null. If
not then warn the user (because this is still a bug that should be
patched) and free the old pointer to prevent memleak/tcp problems.
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7e4c6a3031c74078dba7fa36239d0f4fe476c53 ]
If during the quota disable we fail when cleaning the quota tree or when
deleting the root from the root tree, we jump to the 'out' label without
ever dropping the reference on the quota root, resulting in a leak of the
root since fs_info->quota_root is no longer pointing to the root (we have
set it to NULL just before those steps).
Fix this by always doing a btrfs_put_root() call under the 'out' label.
This is a problem that exists since qgroups were first added in 2012 by
commit bed92eae26cc ("Btrfs: qgroup implementation and prototypes"), but
back then we missed a kfree on the quota root and free_extent_buffer()
calls on its root and commit root nodes, since back then roots were not
yet reference counted.
Reviewed-by: Boris Burkov <boris@bur.io>
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c49908634a2b97b1c3abe0589be2739ac5e7fd5 ]
[BUG]
When running btrfs/060 with forced RST feature, it would crash the
following ASSERT() inside scrub_read_endio():
ASSERT(sector_nr < stripe->nr_sectors);
Before that, we would have tree dump from
btrfs_get_raid_extent_offset(), as we failed to find the RST entry for
the range.
[CAUSE]
Inside scrub_submit_extent_sector_read() every time we allocated a new
bbio we immediately called btrfs_map_block() to make sure there was some
RST range covering the scrub target.
But if btrfs_map_block() fails, we immediately call endio for the bbio,
while the bbio is newly allocated, it's completely empty.
Then inside scrub_read_endio(), we go through the bvecs to find
the sector number (as bi_sector is no longer reliable if the bio is
submitted to lower layers).
And since the bio is empty, such bvecs iteration would not find any
sector matching the sector, and return sector_nr == stripe->nr_sectors,
triggering the ASSERT().
[FIX]
Instead of calling btrfs_map_block() after allocating a new bbio, call
btrfs_map_block() first.
Since our only objective of calling btrfs_map_block() is only to update
stripe_len, there is really no need to do that after btrfs_alloc_bio().
This new timing would avoid the problem of handling empty bbio
completely, and in fact fixes a possible race window for the old code,
where if the submission thread is the only owner of the pending_io, the
scrub would never finish (since we didn't decrease the pending_io
counter).
Although the root cause of RST lookup failure still needs to be
addressed.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b27ea279556121b54d3f45d0529706cf100cdb3a ]
On the LG Gram 16Z90S, the WMAB and WMBB ACPI methods are not mapped
under \XINI, but instead are mapped under \_SB.XINI.
The reason for this is that the LGEX0820 ACPI device used by this
driver is mapped at \_SB.XINI, so the ACPI methods where moved as well
to appear below the LGEX0820 ACPI device.
Fix this by using the ACPI handle from the ACPI device when evaluating
both methods.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218901
Tested-by: Agathe Boutmy <agathe@boutmy.com>
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240606233540.9774-5-W_Armin@gmx.de
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58a54f27a0dac81f7fd3514be01012635219a53c ]
The LGEX0815 ACPI device id is used for handling hotkey events, but
this functionality is already handled by the wireless-hotkey driver.
The LGEX0820 ACPI device id however is used to manage various
platform features using the WMAB/WMBB ACPI methods. Use this ACPI
device id to avoid blocking the wireless-hotkey driver from probing.
Tested-by: Agathe Boutmy <agathe@boutmy.com>
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240606233540.9774-4-W_Armin@gmx.de
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 413c204595ca98a4f33414a948c18d7314087342 ]
The rfkill hotkey handling is already provided by the wireless-hotkey
driver. Remove the now unnecessary rfkill hotkey handling to avoid
duplicating functionality.
The ACPI notify handler still prints debugging information when
receiving ACPI notifications to aid in reverse-engineering.
Tested-by: Agathe Boutmy <agathe@boutmy.com>
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240606233540.9774-3-W_Armin@gmx.de
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 151e78a0b89ee6dec93382dbdf5b1ef83f9c4716 ]
The LGEX0815 ACPI device is used by the "LG Airplane Mode Button"
Windows driver for handling rfkill requests. When the ACPI device
receives an 0x80 ACPI notification, an rfkill event is to be
send to userspace.
Add support for the LGEX0815 ACPI device to the driver.
Tested-by: Agathe Boutmy <agathe@boutmy.com>
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240606233540.9774-2-W_Armin@gmx.de
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d56fbfbaf592a115b2e11c1044829afba34069d2 ]
Add check for the return value of platform_device_add_resources() and
return the error if it fails in order to catch the error.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Link: https://lore.kernel.org/r/20240605032745.2916183-1-nichen@iscas.ac.cn
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 02ea312055da84e08e3e5bce2539c1ff11c8b5f2 ]
Fix unintended sign extension and klockwork issues. These are not real
issue but for sanity checks.
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bfc6444b57dc7186b6acc964705d7516cbaf3904 ]
Ensure that `i2c_lock' is held when setting interrupt latch and mask in
pca953x_irq_bus_sync_unlock() in order to avoid races.
The other (non-probe) call site pca953x_gpio_set_multiple() ensures the
lock is held before calling pca953x_write_regs().
The problem occurred when a request raced against irq_bus_sync_unlock()
approximately once per thousand reboots on an i.MX8MP based system.
* Normal case
0-0022: write register AI|3a {03,02,00,00,01} Input latch P0
0-0022: write register AI|49 {fc,fd,ff,ff,fe} Interrupt mask P0
0-0022: write register AI|08 {ff,00,00,00,00} Output P3
0-0022: write register AI|12 {fc,00,00,00,00} Config P3
* Race case
0-0022: write register AI|08 {ff,00,00,00,00} Output P3
0-0022: write register AI|08 {03,02,00,00,01} *** Wrong register ***
0-0022: write register AI|12 {fc,00,00,00,00} Config P3
0-0022: write register AI|49 {fc,fd,ff,ff,fe} Interrupt mask P0
Signed-off-by: Ian Ray <ian.ray@gehealthcare.com>
Link: https://lore.kernel.org/r/20240620042915.2173-1-ian.ray@gehealthcare.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 00418d5530ca1f42d8721fe0a3e73d1ae477c223 ]
Fill this in so user-space can identify multiple ports on the same CP
unit.
Signed-off-by: Aryan Srivastava <aryan.srivastava@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d34d8163fd87978a6abd792e2d8ad849f4c3d57 ]
As the potential failure of usb_submit_urb(), it should be better to
return the err variable to catch the error.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Link: https://lore.kernel.org/all/20240521041020.1519416-1-nichen@iscas.ac.cn
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c7b1be19b228b450c2945ec379d7fc6bfef9852 ]
As the driver supports more devices over time the single MODULE_ALIAS
is complete and raises several warnings:
SPI driver ads7846 has no spi_device_id for ti,tsc2046
SPI driver ads7846 has no spi_device_id for ti,ads7843
SPI driver ads7846 has no spi_device_id for ti,ads7845
SPI driver ads7846 has no spi_device_id for ti,ads7873
Fix this by adding a spi_device_id table and removing the manual
MODULE_ALIAS.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20240619122703.2081476-1-alexander.stein@ew.tq-group.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9570a48847e3acfa1a741cef431c923325ddc637 ]
The value of NVME_NS_DEAC is 3,
which means NVME_NS_METADATA_SUPPORTED | NVME_NS_EXT_LBAS. Provide a
unique value for this feature flag.
Fixes 1b96f862eccc ("nvme: implement the DEAC bit for the Write Zeroes command")
Signed-off-by: Boyang Yu <yuboyang@dapustor.com>
Reviewed-by: Kanchan Joshi <joshi.k@samsung.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8af49868e51ed1ba117b74728af12abe1eda82e5 ]
If the ASP1 DAI is hooked up by the machine driver the ASP TX mixer
sources should be initialized to disconnected. There aren't currently
any available products using the ASP so this doesn't affect any
existing systems.
The cs35l56 does not have any fixed default for the mixer source
registers. When the cs35l56 boots, its firmware patches these registers
to setup a system-specific routing; this is so that Windows can use
generic SDCA drivers instead of needing knowledge of chip-specific
registers. The setup varies between end-products, which each have
customized firmware, and so the default register state varies between
end-products. It can also change if the firmware on an end-product is
upgraded - for example if a change was needed to the routing for Windows
use-cases. It must be emphasized that the settings applied by the
firmware are not internal magic tuning; they are statically implementing
use-case setup that on Linux would be done via ALSA controls.
The driver is currently syncing the mixer controls with whatever
initial state the firmware wrote to the registers, so that they report
the actual audio routing. But if the ASP DAI is hooked up this can create
a powered-up DAPM graph without anything intentionally setting up a path.
This can lead to parts of the audio system powering up unexpectedly.
For example when cs35l56 is connected to cs42l43 using a codec-codec link,
this can create a complete DAPM graph which then powers-up cs42l43. But
the cs42l43 can only be clocked from its SoundWire bus so this causes a
bunch of errors in the kernel log where cs42l43 is unexpectedly powered-up
without a clock.
If the host is taking ownership of the ASP (either directly or as a
codec-to-codec link) there is no need to keep the mixer settings that the
firmware wrote. The driver has ALSA controls for setting these using
standard Linux mechanisms. So if the machine driver hooks up the ASP the
ASP mixers are initialized to "None" (no input). This prevents unintended
DAPM-graph power-ups, and means the initial state of the mixers is
always going to be None.
Since the initial state of the mixers can vary from system to system and
potentially between firmware upgrades, no use-case manager can currently
assume that cs35l56 has a known initial state. The firmware could just as
easily default them to "None" as to any input source. So defaulting them
to "None" in the driver is not increasing the entropy of the system.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20240613132527.46537-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f3b198e4788fcc8d03ed0c8bd5e3856c6a5760c5 ]
Add debounce time in headset type detection for better performance.
Signed-off-by: Jack Yu <jack.yu@realtek.com>
Link: https://lore.kernel.org/r/7e502e9a9dd94122a1b60deb5ceb60fb@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f2a43e3d14f6e31a3b041a1043195d02c54d615 ]
If the ipc_prepare() callback fails for a module instance, on error rewind
we must skip the ipc_unprepare() call for ones that has positive use count.
The positive use count means that the module instance is in active use, it
cannot be unprepared.
The issue affects capture direction paths with branches (single dai with
multiple PCMs), the affected widgets are in the shared part of the paths.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20240612121203.15468-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 524d3f126362b6033e92cbe107ae2158d7fbff94 ]
Set driver name to "HDMI". This simplifies the code and gets rid of
the following error messages:
ASoC: driver name too long 'HDMI 58040000.encoder' -> 'HDMI_58040000_e'
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20240610125847.773394-1-primoz.fiser@norik.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c5dcf8ab10606e76c1d8a0ec77f27d84a392e874 ]
The minimum period size was enforced to 64 as older devices integrating
McASP with EDMA used an internal FIFO of 64 samples.
With UDMA based platforms this internal McASP FIFO is optional, as the
DMA engine internally does some buffering which is already accounted for
when registering the platform. So we should read the actual FIFO
configuration (txnumevt/rxnumevt) instead of hardcoding frames.min to
64.
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240611-asoc_next-v3-2-fcfd84b12164@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
