Add MODULE_DEVICE_TABLE(), so modules could be properly autoloaded
based on the alias from of_device_id table.
Fixes: 9e8269de10 ("hwmon: (ntc_thermistor) Add DT with IIO support to NTC thermistor driver")
Signed-off-by: Yuntao Liu <liuyuntao12@huawei.com>
Message-ID: <20240815083021.756134-1-liuyuntao12@huawei.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The sysfs does not like that we name the thermistor something
that contains a dash:
ntc-thermistor thermistor: hwmon: 'ssg1404-001221' is not a valid
name attribute, please fix
Fix it up by switching to an underscore.
Fixes: e13e979b2b ("hwmon: (ntc_thermistor) Add Samsung 1404-001221 NTC")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220205005804.123245-1-linus.walleij@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This adds the Samsung 1404-001221 NTC thermistor to the
NTC thermistor driver. As far as I can tell it is electrically
compatible with the Murata 47K NTC thermistor.
This thermistor is mounted in a variety of Samsung products.
Cc: Peter Rosin <peda@axentia.se>
Cc: Chris Lesiak <chris.lesiak@licor.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211215174241.1496169-1-linus.walleij@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This moves the device tree match data toward the end of the
driver which is the convention, here we can also add ACPI
and similar match data in a conforming manner.
Cc: Peter Rosin <peda@axentia.se>
Cc: Chris Lesiak <chris.lesiak@licor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20211205235948.4167075-3-linus.walleij@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This switches to retrieveing the configuration of the NTC
from generic firmware properties so that we get neutral from
device tree: now ACPI or, more importantly, software nodes
can be used to spawn NTC devices provided they have the
required properties.
This was inspired by the similar changes made to the IIO
drivers.
This was tested on the Ux500 HREF with the NTC devices
probing from device tree just as fine after this as before.
Cc: Peter Rosin <peda@axentia.se>
Cc: Chris Lesiak <chris.lesiak@licor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20211206020423.62402-2-linus.walleij@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Move the parsing of the DT config right above probe().
Allocate the state container for the driver in probe()
instead of inside the DT config parsing function: as a
result return an int instead of a pointer.
Drop the check for !np: we can only probe from DT right
now so no risk of ending up here.
Cc: Peter Rosin <peda@axentia.se>
Cc: Chris Lesiak <chris.lesiak@licor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20211206020423.62402-1-linus.walleij@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Allocate one state container for the device: struct ntc_data.
Move all items from struct ntc_thermistor_platform_data into
this struct and simplify.
Cc: Peter Rosin <peda@axentia.se>
Cc: Chris Lesiak <chris.lesiak@licor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20211125020841.3616359-5-linus.walleij@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The only possible assignment of a function to get a voltage to
convert to a resistance is to use the internal function
ntc_adc_iio_read() which is only available when using IIO
and OF.
Bite the bullet and mandate OF and IIO, drop the read_uv()
callback abstraction and some ifdefs.
As no board is using the platform data, all users are using
OF and IIO anyway.
Cc: Peter Rosin <peda@axentia.se>
Cc: Chris Lesiak <chris.lesiak@licor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20211125020841.3616359-4-linus.walleij@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Nothing in the kernel (this driver) is using the callback to
read ohms directly. We always read a voltage and convert it
to a resistance. Drop this callback.
Cc: Peter Rosin <peda@axentia.se>
Cc: Chris Lesiak <chris.lesiak@licor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20211125020841.3616359-3-linus.walleij@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Platform data is supposed to be used with "board files",
device descriptions in C. Since the introduction of the
NTC driver in 2011, no such platforms have been submitted
to the Linux kernel, and their use is strongly discouraged
in favor of Device Tree, ACPI or as last resort software
firmware nodes.
Drop the external header and copy the platform data into
the driver file.
Cc: Peter Rosin <peda@axentia.se>
Cc: Chris Lesiak <chris.lesiak@licor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20211125020841.3616359-2-linus.walleij@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The kernel has a helper function for linear interpolation so
use it. It incidentally makes the code easier to read as well.
Tested on the ST-Ericsson HREFv60plus hardware reference design
with two thermistors forming a thermal zone.
Cc: Peter Rosin <peda@axentia.se>
Cc: Chris Lesiak <chris.lesiak@licor.com>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210704222014.12058-1-linus.walleij@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The IIO usage in this driver is purely consumer so it should only
be including linux/iio/consumer.h Whilst here drop pm_runtime.h
as there is no runtime power management in the driver.
Found using include-what-you-use and manual inspection of the
suggestions.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210611142257.103094-1-jic23@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Before trying the custom method of reading the sensor
as raw and then converting, we want to use
iio_read_channel_processed_scale() which first tries to
see if the ADC can provide a processed value directly,
else reads raw and applies scaling inside of IIO
using the scale attributes of the ADC. We need to
multiply the scaled value with 1000 to get to
microvolts from millivolts which is what processed
IIO channels returns.
Keep the code that assumes 12bit ADC around as a
fallback.
This gives correct readings on the AB8500 thermistor
inputs used in the Ux500 HREFP520 platform for reading
battery and board temperature.
Cc: Peter Rosin <peda@axentia.se>
Cc: Chris Lesiak <chris.lesiak@licor.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: linux-iio@vger.kernel.org
Link: https://lore.kernel.org/linux-iio/20201224011607.1059534-1-linus.walleij@linaro.org/
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Chris Lesiak <chris.lesiak@licor.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210308100219.2732156-2-linus.walleij@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
59 temple place suite 330 boston ma 02111 1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1334 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.113240726@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 7cc7de93fa ("hwmon: (ntc_thermistor) Convert to new hwmon API")
converted the driver to use the new hwmon API, but introduced a subtle
error: The temperature type is no longer reported as temp1_type, but as
temp2_type.
Fixes: 7cc7de93fa ("hwmon: (ntc_thermistor) Convert to new hwmon API")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use devm_hwmon_device_register_with_info() instead of
devm_hwmon_device_register_with_groups() to register the hwmon
device to simplify the code and make it easier to maintain.
As part of this change, thermal device registration is moved into
the hwmon core.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use an enum to index the array, so that it is possible to add sorted
entries without causing churn.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Instead of repeatedly accessing &pdev->dev, use a local variable dev
instead where possible. Also drop 'dev' from private data since it is
unnecessary.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This changes the driver to use the devm_ version
of thermal_zone_of_sensor_register and cleans
up the local points and unregister calls.
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: lm-sensors@lm-sensors.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch adds support for the Murata NCP15XH103 thermistor series.
Signed-off-by: Joseph McNally <jmcna06@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The thermal code uses int, long and unsigned long for temperatures
in different places.
Using an unsigned type limits the thermal framework to positive
temperatures without need. Also several drivers currently will report
temperatures near UINT_MAX for temperatures below 0°C. This will probably
immediately shut the machine down due to overtemperature if started below
0°C.
'long' is 64bit on several architectures. This is not needed since INT_MAX °mC
is above the melting point of all known materials.
Consistently use a plain 'int' for temperatures throughout the thermal code and
the drivers. This only changes the places in the drivers where the temperature
is passed around as pointer, when drivers internally use another type this is
not changed.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Reviewed-by: Darren Hart <dvhart@linux.intel.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Peter Feuerer <peter@piie.net>
Cc: Punit Agrawal <punit.agrawal@arm.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Peter Feuerer <peter@piie.net>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-acpi@vger.kernel.org
Cc: platform-driver-x86@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-omap@vger.kernel.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Darren Hart <dvhart@infradead.org>
Cc: lm-sensors@lm-sensors.org
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The function get_ohm_of_thermistor has both the measured voltage and the
pullup voltage available in microvolts. But it was promptly converting
both to millivolts before using them to calculate the thermistor
resistance. That conversion unnecessarily hurt the precision of the
calculation.
For example, take the ncpXXwb473 connected to 5000 mV and pulled down
through a 47000 ohm resistor. At 25 C, the resistance of the thermistor
is 47000 ohms. The measured voltage will be 2500 mV. If we measure
instead 2501 mV, then the calculated resistance will be 46962 ohms --
a difference of 38 ohms. So the precision of the resistance estimate
could be increased by 38X by doing the calculations in microvolts.
Signed-off-by: Chris Lesiak <chris.lesiak@licor.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The function ntc_adc_iio_read was assuming both a 12 bit ADC and that
pullup_uv is the same as the ADC reference voltage. If either
assumption is false, then the result is incorrect.
Attempt to use iio_convert_raw_to_processed to convert the raw value to
microvolts. It will fail for iio channels that don't support support
IIO_CHAN_INFO_SCALE; in that case fall back to the assumptions.
Signed-off-by: Chris Lesiak <chris.lesiak@licor.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch adds support for the ntc thermistor NCPXXWF104 series.
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When configured via device tree, the associated iio device needs to be
measuring voltage for the conversion to resistance to be correct.
Return -EINVAL if that is not the case.
Signed-off-by: Chris Lesiak <chris.lesiak@licor.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull thermal management update from Zhang Rui:
"Summary:
- of-thermal extension to allow drivers to register and use its
functionality in a better way, without exploiting thermal core.
From Lukasz Majewski.
- Fix a bug in intel_soc_dts_thermal driver which calls a sleep
function in interrupt handler. From Maurice Petallo.
- add a thermal UAPI header file for exporting the thermal generic
netlink information to user-space. From Florian Fainelli.
- First round of refactoring in Exynos driver. Bartlomiej and Lukasz
are attempting to make it lean and easier to understand.
- New thermal driver for Rockchip (rk3288), with support for DT
thermal. From Caesar Wang.
- New thermal driver for Nvidia, Tegra124 SOCTHERM driver, with
support for DT thermal. From Mikko Perttunen.
- New cooling device, based on common clock framework. From Eduardo
Valentin.
- a couple of small fixes in thermal core framework. From Srinivas
Pandruvada, Javi Merino, Luis Henriques.
- Dropping Armada A375-Z1 SoC thermal support as the chip is not in
the market, armada folks decided to drop its support.
- a couple of small fixes and cleanups in int340x thermal driver"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (58 commits)
thermal: provide an UAPI header file
Thermal/int340x: Clear the error value of the last acpi_bus_get_device() call
thermal/powerclamp: add id for braswell cpu
thermal: Intel SoC DTS: Don't do thermal zone update inside spin_lock
Thermal: fix platform_no_drv_owner.cocci warnings
Thermal/int340x: avoid unnecessary pointer casting
thermal: int3403: Delete a check before thermal_zone_device_unregister()
thermal/int3400: export uuids
thermal: of: Extend current of-thermal.c code to allow setting emulated temp
thermal: of: Extend of-thermal to export table of trip points
thermal: of: Rename struct __thermal_trip to struct thermal_trip
thermal: of: Extend of-thermal.c to provide check if trip point is valid
thermal: of: Extend of-thermal.c to provide number of trip points
thermal: Fix error path in thermal_init()
thermal: lock the thermal zone when switching governors
thermal: core: ignore invalid trip temperature
thermal: armada: Remove support for A375-Z1 SoC
thermal: rockchip: add driver for thermal
dt-bindings: document Rockchip thermal
thermal: exynos: remove exynos_tmu_data.h include
...
Different drivers request API extensions in of-thermal. For this reason,
additional callbacks are required to fit the new drivers needs.
The current API implementation expects the registering sensor driver
to provide a get_temp and get_trend callbacks as function parameters.
As the amount of callbacks is growing, this patch changes the existing
implementation to use a .ops field to hold all the of thermal callbacks
to sensor drivers.
This patch also changes the existing of-thermal users to fit the new
API design. No functional change is introduced in this patch.
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: devicetree@vger.kernel.org
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jean Delvare <jdelvare@suse.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Cc: lm-sensors@lm-sensors.org
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Mikko Perttunen <mikko.perttunen@kapsi.fi>
Reviewed-by: Mikko Perttunen <mikko.perttunen@kapsi.fi>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
To get more comprehensive and integrated thermal management, it adds ntc
thermistor to thermal framework as a thermal sensor. It's governed thermal
susbsystem only if it is described in DT node. Otherwise, it just notifies
temperature to userspace via sysfs as it used to be.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch adds support for the ntc thermistor B57330V2103 from EPCOS.
Signed-off-by: Johannes Pointner <johannes.pointner@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Currently, dev_info() at the end of the probe says
"type:%s ". But, prints pdev->name.
This patch uses "pdev_id->name" which prints the thermistor type.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Murata Manufacturing Co., Ltd is the vendor for
NTC (Negative Temperature coefficient) based Thermistors.
But, the driver extensively uses "NTC" as the vendor name.
This patch corrects the vendor name also updates the
compatibility strings according to the vendor-prefix.txt
Note: Drivers continue to support the previous compatible strings
but further addition of these compatible strings in device tree
is deprecated.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The mapping from OF device IDs to platform device IDs is wrong.
TYPE_NCPXXWB473 is 0, TYPE_NCPXXWL333 is 1, so
ntc_thermistor_id[TYPE_NCPXXWB473] is { "ncp15wb473", TYPE_NCPXXWB473 }
while
ntc_thermistor_id[TYPE_NCPXXWL333] is { "ncp18wb473", TYPE_NCPXXWB473 }.
So the name is wrong for all but the "ntc,ncp15wb473" entry, and the
type is wrong for the "ntc,ncp15wl333" entry.
So map the entries by index, it is neither elegant nor robust but at
least it is correct.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: 9e8269de hwmon: (ntc_thermistor) Add DT with IIO support to NTC thermistor driver
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Cc: Doug Anderson <dianders@chromium.org>
In commit 9e8269de, support was added for ntc_thermistor devices being
declared in the device tree and implemented on top of IIO. With that
change, a dependency was added to the ntc_thermistor driver:
depends on (!OF && !IIO) || (OF && IIO)
This construct has the drawback that the driver can no longer be
selected when OF is set and IIO isn't, nor when IIO is set and OF is
not. This is a regression for the original users of the driver.
As the new code depends on IIO and is useless without OF, include it
only if both are enabled, and set the dependencies accordingly. This
is clearer, more simple and more correct.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: 9e8269de hwmon: (ntc_thermistor) Add DT with IIO support to NTC thermistor driver
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Cc: Doug Anderson <dianders@chromium.org>
The ntc thermistor code was doing math whose temporary result might
have overflowed 32-bits. We need some casts in there to make it safe.
In one example I found:
- pullup_uV: 1800000
- result of iio_read_channel_raw: 3226
- 1800000 * 3226 => 0x15a1cbc80
Signed-off-by: Doug Anderson <dianders@chromium.org>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch adds DT support to NTC driver to parse the
platform data.
Also adds the support to work as an iio device client.
During the probe ntc driver gets the respective channels of ADC
and uses iio_raw_read calls to get the ADC converted value.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
[Guenter Roeck: fixed Kconfig dependencies; use ERR_CAST]
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fixes the following sparse warnings:
drivers/hwmon/ntc_thermistor.c:46:31: warning:
symbol 'ncpXXwb473' was not declared. Should it be static?
drivers/hwmon/ntc_thermistor.c:82:31: warning:
symbol 'ncpXXwl333' was not declared. Should it be static?
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Alistair John Strachan <alistair@devzero.co.uk>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Juerg Haefliger <juergh@gmail.com>
Cc: Andreas Herrmann <herrmann.der.user@googlemail.com>
Cc: Clemens Ladisch <clemens@ladisch.de>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Jim Cromie <jim.cromie@gmail.com>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Roger Lucas <vt8231@hiddenengine.co.uk>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Alistair John Strachan <alistair@devzero.co.uk>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Juerg Haefliger <juergh@gmail.com>
Cc: Andreas Herrmann <herrmann.der.user@googlemail.com>
Cc: Clemens Ladisch <clemens@ladisch.de>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Jim Cromie <jim.cromie@gmail.com>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Roger Lucas <vt8231@hiddenengine.co.uk>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Alistair John Strachan <alistair@devzero.co.uk>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Juerg Haefliger <juergh@gmail.com>
Cc: Andreas Herrmann <herrmann.der.user@googlemail.com>
Cc: Clemens Ladisch <clemens@ladisch.de>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Jim Cromie <jim.cromie@gmail.com>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Roger Lucas <vt8231@hiddenengine.co.uk>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
