HYPERVISOR_get_debugreg() is being called from noinstr code, so it
should be attributed "always_inline".
Fixes: f4afb713e5c3a4419ba ("x86/xen: Make get_debugreg() noinstr")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/20211125092056.24758-2-jgross@suse.com
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
- add a NO APST quirk for a Kioxia device (Enzo Matsumiya)
- fix write zeroes pi (Klaus Jensen)
- various TCP transport fixes (Maurizio Lombardi and Varun Prakash)
- ignore invalid fast_io_fail_tmo values (Maurizio Lombardi)
- use IOCB_NOWAIT only if the filesystem supports it (Maurizio Lombardi)
-----BEGIN PGP SIGNATURE-----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=Hjjj
-----END PGP SIGNATURE-----
Merge tag 'nvme-5.16-2021-11-25' of git://git.infradead.org/nvme into block-5.16
Pull NVMe fixes from Christoph:
"nvme fixes for Linux 5.16
- add a NO APST quirk for a Kioxia device (Enzo Matsumiya)
- fix write zeroes pi (Klaus Jensen)
- various TCP transport fixes (Maurizio Lombardi and Varun Prakash)
- ignore invalid fast_io_fail_tmo values (Maurizio Lombardi)
- use IOCB_NOWAIT only if the filesystem supports it (Maurizio Lombardi)"
* tag 'nvme-5.16-2021-11-25' of git://git.infradead.org/nvme:
nvmet: use IOCB_NOWAIT only if the filesystem supports it
nvme: fix write zeroes pi
nvme-fabrics: ignore invalid fast_io_fail_tmo values
nvme-pci: add NO APST quirk for Kioxia device
nvme-tcp: fix memory leak when freeing a queue
nvme-tcp: validate R2T PDU in nvme_tcp_handle_r2t()
nvmet-tcp: fix incomplete data digest send
nvmet-tcp: fix memory leak when performing a controller reset
nvmet-tcp: add an helper to free the cmd buffers
nvmet-tcp: fix a race condition between release_queue and io_work
Submit I/O requests with the IOCB_NOWAIT flag set only if
the underlying filesystem supports it.
Fixes: 50a909db36f2 ("nvmet: use IOCB_NOWAIT for file-ns buffered I/O")
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
We add the ostd setting for mt8195. It introduces a KE for the
previous SoC which doesn't have ostd setting. This is the log:
Unable to handle kernel NULL pointer dereference at virtual address
0000000000000080
...
pc : mtk_smi_larb_config_port_gen2_general+0x64/0x130
lr : mtk_smi_larb_resume+0x54/0x98
...
Call trace:
mtk_smi_larb_config_port_gen2_general+0x64/0x130
pm_generic_runtime_resume+0x2c/0x48
__genpd_runtime_resume+0x30/0xa8
genpd_runtime_resume+0x94/0x2c8
__rpm_callback+0x44/0x150
rpm_callback+0x6c/0x78
rpm_resume+0x310/0x558
__pm_runtime_resume+0x3c/0x88
In the code: larbostd = larb->larb_gen->ostd[larb->larbid],
if "larb->larb_gen->ostd" is null, the "larbostd" is the offset(e.g.
0x80 above), it's also a valid value, then accessing "larbostd[i]" in the
"for" loop will cause the KE above. To avoid this issue, initialize
"larbostd" to NULL when the SoC doesn't have ostd setting.
Fixes: fe6dd2a4017d ("memory: mtk-smi: mt8195: Add initial setting for smi-larb")
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20211108082429.15080-1-yong.wu@mediatek.com
Link: https://lore.kernel.org/r/20211124085042.9649-3-krzysztof.kozlowski@canonical.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Switch the kernel tree for keystone to the consolidated ti tree and add
myself as primary maintainer for keystone platforms to offset Santosh's
workload.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Link: https://lore.kernel.org/r/20211123001725.21422-1-nm@ti.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Checking buf->flags should be done before the pipe_buf_release() is called
on the pipe buffer, since releasing the buffer might modify the flags.
This is exactly what page_cache_pipe_buf_release() does, and which results
in the same VM_BUG_ON_PAGE(PageLRU(page)) that the original patch was
trying to fix.
Reported-by: Justin Forbes <jmforbes@linuxtx.org>
Fixes: 712a951025c0 ("fuse: fix page stealing")
Cc: <stable@vger.kernel.org> # v2.6.35
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Here's a fix for a pl2303 type-detection issue and some new modem
devices ids.
All but the last commit have been in linux-next, and with no reported
issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCYZ97TgAKCRALxc3C7H1l
CA9CAP9c8DY1tsmARjgRsUV0QznBFhTssMTPGNMy1m5g3tpJ9gEArbBcM86J6yzn
MpHIGUZyL0gYPEZEP+eA12VOJsir2gE=
=bMIF
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.16-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.16-rc3
Here's a fix for a pl2303 type-detection issue and some new modem
devices ids.
All but the last commit have been in linux-next, and with no reported
issues.
* tag 'usb-serial-5.16-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Fibocom FM101-GL variants
USB: serial: pl2303: fix GC type detection
USB: serial: option: add Telit LE910S1 0x9200 composition
Just like before with __bswapdi2(), for MIPS pre-boot when
CONFIG_KERNEL_ZSTD=y the decompressor function will use __ashldi3(), so
the object file should be added to the target object file.
Fixes these build errors:
mipsel-linux-ld: arch/mips/boot/compressed/decompress.o: in function `FSE_buildDTable_internal':
decompress.c:(.text.FSE_buildDTable_internal+0x48): undefined reference to `__ashldi3'
mipsel-linux-ld: arch/mips/boot/compressed/decompress.o: in function `FSE_decompress_wksp_body_default':
decompress.c:(.text.FSE_decompress_wksp_body_default+0xa8): undefined reference to `__ashldi3'
mipsel-linux-ld: arch/mips/boot/compressed/decompress.o: in function `ZSTD_getFrameHeader_advanced':
decompress.c:(.text.ZSTD_getFrameHeader_advanced+0x134): undefined reference to `__ashldi3'
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
If xattr is not supported like exfat or fat, ksmbd server doesn't
contain default data stream in FILE_STREAM_INFORMATION response. It will
cause ppt or doc file update issue if local filesystem is such as ones.
This patch move goto statement to contain it.
Fixes: 9f6323311c70 ("ksmbd: add default data stream name in FILE_STREAM_INFORMATION")
Cc: stable@vger.kernel.org # v5.15
Acked-by: Hyunchul Lee <hyc.lee@gmail.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
While file transfer through windows client, This error flood message
happen. This flood message will cause performance degradation and
misunderstand server has problem.
Fixes: e294f78d3478 ("ksmbd: allow PROTECTED_DACL_SECINFO and UNPROTECTED_DACL_SECINFO addition information in smb2 set info security")
Cc: stable@vger.kernel.org # v5.15
Acked-by: Hyunchul Lee <hyc.lee@gmail.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
In some senteces there were missing spaces between words.
Fix wording in item to show which prints are enabled and add a space
beween the cat command and its argument.
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Steve French <sfrench@samba.org>
CC: Hyunchul Lee <hyc.lee@gmail.com>
Cc: linux-cifs@vger.kernel.org
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Salvatore Bonaccorso <carnil@debian.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
All the error handling paths of 'smb2_sess_setup()' end to 'out_err'.
All but the new error handling path added by the commit given in the Fixes
tag below.
Fix this error handling path and branch to 'out_err' as well.
Fixes: 0d994cd482ee ("ksmbd: add buffer validation in session setup")
Cc: stable@vger.kernel.org # v5.15
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Steve French <stfrench@microsoft.com>
Karsten Graul says:
====================
net/smc: fixes 2021-11-24
Patch 1 from DaXing fixes a possible loop in smc_listen().
Patch 2 prevents a NULL pointer dereferencing while iterating
over the lower network devices.
====================
Link: https://lore.kernel.org/r/20211124123238.471429-1-kgraul@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The kernel_listen function in smc_listen will fail when all the available
ports are occupied. At this point smc->clcsock->sk->sk_data_ready has
been changed to smc_clcsock_data_ready. When we call smc_listen again,
now both smc->clcsock->sk->sk_data_ready and smc->clcsk_data_ready point
to the smc_clcsock_data_ready function.
The smc_clcsock_data_ready() function calls lsmc->clcsk_data_ready which
now points to itself resulting in an infinite loop.
This patch restores smc->clcsock->sk->sk_data_ready with the old value.
Fixes: a60a2b1e0af1 ("net/smc: reduce active tcp_listen workers")
Signed-off-by: Guo DaXing <guodaxing@huawei.com>
Acked-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Coverity reports a possible NULL dereferencing problem:
in smc_vlan_by_tcpsk():
6. returned_null: netdev_lower_get_next returns NULL (checked 29 out of 30 times).
7. var_assigned: Assigning: ndev = NULL return value from netdev_lower_get_next.
1623 ndev = (struct net_device *)netdev_lower_get_next(ndev, &lower);
CID 1468509 (#1 of 1): Dereference null return value (NULL_RETURNS)
8. dereference: Dereferencing a pointer that might be NULL ndev when calling is_vlan_dev.
1624 if (is_vlan_dev(ndev)) {
Remove the manual implementation and use netdev_walk_all_lower_dev() to
iterate over the lower devices. While on it remove an obsolete function
parameter comment.
Fixes: cb9d43f67754 ("net/smc: determine vlan_id of stacked net_device")
Suggested-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Marek Behún says:
====================
phylink resolve fixes
With information from me and my nagging, Russell has produced two fixes
for phylink, which add code that triggers another phylink_resolve() from
phylink_resolve(), if certain conditions are met:
interface is being changed
or
link is down and previous link was up
These are needed because sometimes the PCS callbacks may provide stale
values if link / speed / ...
====================
Link: https://lore.kernel.org/r/20211123154403.32051-1-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On mv88e6xxx 1G/2.5G PCS, the SerDes register 4.2001.2 has the following
description:
This register bit indicates when link was lost since the last
read. For the current link status, read this register
back-to-back.
Thus to get current link state, we need to read the register twice.
But doing that in the link change interrupt handler would lead to
potentially ignoring link down events, which we really want to avoid.
Thus this needs to be solved in phylink's resolve, by retriggering
another resolve in the event when PCS reports link down and previous
link was up, and by re-reading PCS state if the previous link was down.
The wrong value is read when phylink requests change from sgmii to
2500base-x mode, and link won't come up. This fixes the bug.
Fixes: 9525ae83959b ("phylink: add phylink infrastructure")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On PHY state change the phylink_resolve() function can read stale
information from the MAC and report incorrect link speed and duplex to
the kernel message log.
Example with a Marvell 88X3310 PHY connected to a SerDes port on Marvell
88E6393X switch:
- PHY driver triggers state change due to PHY interface mode being
changed from 10gbase-r to 2500base-x due to copper change in speed
from 10Gbps to 2.5Gbps, but the PHY itself either hasn't yet changed
its interface to the host, or the interrupt about loss of SerDes link
hadn't arrived yet (there can be a delay of several milliseconds for
this), so we still think that the 10gbase-r mode is up
- phylink_resolve()
- phylink_mac_pcs_get_state()
- this fills in speed=10g link=up
- interface mode is updated to 2500base-x but speed is left at 10Gbps
- phylink_major_config()
- interface is changed to 2500base-x
- phylink_link_up()
- mv88e6xxx_mac_link_up()
- .port_set_speed_duplex()
- speed is set to 10Gbps
- reports "Link is Up - 10Gbps/Full" to dmesg
Afterwards when the interrupt finally arrives for mv88e6xxx, another
resolve is forced in which we get the correct speed from
phylink_mac_pcs_get_state(), but since the interface is not being
changed anymore, we don't call phylink_major_config() but only
phylink_mac_config(), which does not set speed/duplex anymore.
To fix this, we need to force the link down and trigger another resolve
on PHY interface change event.
Fixes: 9525ae83959b ("phylink: add phylink infrastructure")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Usage of phy_ethtool_get_link_ksettings() in the link status change
handler isn't needed, and in combination with the referenced change
it results in a deadlock. Simply remove the call and replace it with
direct access to phydev->speed. The duplex argument of
lan743x_phy_update_flowcontrol() isn't used and can be removed.
Fixes: c10a485c3de5 ("phy: phy_ethtool_ksettings_get: Lock the phy for consistency")
Reported-by: Alessandro B Maurici <abmaurici@gmail.com>
Tested-by: Alessandro B Maurici <abmaurici@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/40e27f76-0ba3-dcef-ee32-a78b9df38b0f@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While testing BIG TCP patch series, I was expecting that TCP_RR workloads
with 80KB requests/answers would send one 80KB TSO packet,
then being received as a single GRO packet.
It turns out this was not happening, and the root cause was that
cubic Hystart ACK train was triggering after a few (2 or 3) rounds of RPC.
Hystart was wrongly setting CWND/SSTHRESH to 30, while my RPC
needed a budget of ~20 segments.
Ideally these TCP_RR flows should not exit slow start.
Cubic Hystart should reset itself at each round, instead of assuming
every TCP flow is a bulk one.
Note that even after this patch, Hystart can still trigger, depending
on scheduling artifacts, but at a higher CWND/SSTHRESH threshold,
keeping optimal TSO packet sizes.
Tested:
ip link set dev eth0 gro_ipv6_max_size 131072 gso_ipv6_max_size 131072
nstat -n; netperf -H ... -t TCP_RR -l 5 -- -r 80000,80000 -K cubic; nstat|egrep "Ip6InReceives|Hystart|Ip6OutRequests"
Before:
8605
Ip6InReceives 87541 0.0
Ip6OutRequests 129496 0.0
TcpExtTCPHystartTrainDetect 1 0.0
TcpExtTCPHystartTrainCwnd 30 0.0
After:
8760
Ip6InReceives 88514 0.0
Ip6OutRequests 87975 0.0
Fixes: ae27e98a5152 ("[TCP] CUBIC v2.3")
Co-developed-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Link: https://lore.kernel.org/r/20211123202535.1843771-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Update the B53 Ethernet switch section to contain
drivers/net/dsa/bcm_sf2*.
Reported-by: Russell King (Oracle) <linux@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20211123222422.3745485-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stefan Schmidt says:
====================
pull-request: ieee802154 for net 2021-11-24
A fix from Alexander which has been brought up various times found by
automated checkers. Make sure values are in u32 range.
* tag 'ieee802154-for-net-2021-11-24' of git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan:
net: ieee802154: handle iftypes as u32
====================
Link: https://lore.kernel.org/r/20211124150934.3670248-1-stefan@datenfreihafen.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The system will crash if we put an uninitialized iova_domain, this
could happen when an error occurs before initializing the iova_domain
in vdpasim_create().
BUG: kernel NULL pointer dereference, address: 0000000000000000
...
RIP: 0010:__cpuhp_state_remove_instance+0x96/0x1c0
...
Call Trace:
<TASK>
put_iova_domain+0x29/0x220
vdpasim_free+0xd1/0x120 [vdpa_sim]
vdpa_release_dev+0x21/0x40 [vdpa]
device_release+0x33/0x90
kobject_release+0x63/0x160
vdpasim_create+0x127/0x2a0 [vdpa_sim]
vdpasim_net_dev_add+0x7d/0xfe [vdpa_sim_net]
vdpa_nl_cmd_dev_add_set_doit+0xe1/0x1a0 [vdpa]
genl_family_rcv_msg_doit+0x112/0x140
genl_rcv_msg+0xdf/0x1d0
...
So we must make sure the iova_domain is already initialized before
put it.
In addition, we may get the following warning in this case:
WARNING: ... drivers/iommu/iova.c:344 iova_cache_put+0x58/0x70
So we must make sure the iova_cache_put() is invoked only if the
iova_cache_get() is already invoked. Let's fix it together.
Cc: stable@vger.kernel.org
Fixes: 4080fc106750 ("vdpa_sim: use iova module to allocate IOVA addresses")
Signed-off-by: Longpeng <longpeng2@huawei.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/r/20211124015215.119-1-longpeng2@huawei.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Vdpa devices should be reset after unseting irqs of virtqueues, or we
will get errors when killing qemu process:
>> pi_update_irte: failed to update PI IRTE
>> irq bypass consumer (token 0000000065102a43) unregistration fails: -22
Signed-off-by: Wu Zongyong <wuzongyong@linux.alibaba.com>
Link: https://lore.kernel.org/r/a2cb60cf73be9da5c4e6399242117d8818f975ae.1636946171.git.wuzongyong@linux.alibaba.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
This was found by coccicheck:
./drivers/block/virtio_blk.c, 334, 14-17, WARNING Unsigned expression
compared with zero num < 0
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Ye Guojin <ye.guojin@zte.com.cn>
Link: https://lore.kernel.org/r/20211117063955.160777-1-ye.guojin@zte.com.cn
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Fixes: 02746e26c39e ("virtio-blk: avoid preallocating big SGL for data")
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
We can increment `total_len` directly and remove `len` since it
is no longer used for vhost_add_used().
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/r/20211122163525.294024-3-sgarzare@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
The "used length" reported by calling vhost_add_used() must be the
number of bytes written by the device (using "in" buffers).
In vhost_vsock_handle_tx_kick() the device only reads the guest
buffers (they are all "out" buffers), without writing anything,
so we must pass 0 as "used length" to comply virtio spec.
Fixes: 433fc58e6bf2 ("VSOCK: Introduce vhost_vsock.ko")
Cc: stable@vger.kernel.org
Reported-by: Halil Pasic <pasic@linux.ibm.com>
Suggested-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/r/20211122163525.294024-2-sgarzare@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
This reverts commit 939779f5152d161b34f612af29e7dc1ac4472fcf.
Attempts to validate length in the core did not work out: there turn out
to exist multiple broken devices, and in particular legacy devices are
known to be broken in this respect.
We have ideas for handling this better in the next version but for now
let's revert to a known good state to make sure drivers work for people.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This reverts commit 816625c13652cef5b2c49082d652875da6f2ad7a.
Attempts to validate length in the core did not work out.
We'll drop them, so revert the dependent changes in drivers.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This reverts commit a40392edf1b2c7822bc0ce68413106661a9d4232.
Attempts to validate length in the core did not work out.
We'll drop them, so revert the dependent changes in drivers.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This reverts commit c57911ebfbfe745cb95da2bcf547c5bae000590f.
Attempts to validate length in the core did not work out. We'll drop
them for now, so revert the dependent changes in drivers.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Update the bios scratch register when updating the backlight
level. Some platforms apparently read this scratch register
and do additional operations in their hotkey handlers.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1518
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The overclocking interface currently appends data to a
string. Revert back to using sprintf().
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1774
Fixes: 6db0c87a0a8ee1 ("amdgpu/pm: Replace hwmgr smu usage of sprintf with sysfs_emit")
Acked-by: Evan Quan <evan.quan@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
There is no need for additional programming, keep the default settings.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
fix some byteorder issues about amdgpu discovery.
This will result in running errors on the big end system. (e.g:MIPS)
Signed-off-by: Yang Wang <KevinYang.Wang@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If xnack is on, VM retry fault interrupt send to IH ring1, and ring1
will be full quickly. IH cannot receive other interrupts, this causes
deadlock if migrating buffer using sdma and waiting for sdma done
while handling retry fault.
Remove VMC from IH storm client, enable ring1 write pointer
overflow, then IH will drop retry fault interrupts and be able to receive
other interrupts while driver is handling retry fault.
IH ring1 write pointer doesn't writeback to memory by IH, and ring1
write pointer recorded by self-irq is not updated, so always read
the latest ring1 write pointer from register.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
By default this timestamp is 32 bit counter. It gets overflowed in
around 10 minutes.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
unmap range always increase atomic svms->drain_pagefaults to simplify
both parent range and child range unmap, page fault handle ignores the
retry fault if svms->drain_pagefaults is set to speed up interrupt
handling. svm_range_drain_retry_fault restart draining if another
range unmap from cpu.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
VMA may be removed before unmap notifier callback, and deferred list
work remove range, return success for this special case as we are
handling stale retry fault.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
kfd_process_wq_release drain retry fault to ensure no retry fault comes
after removing kfd process from the hash table, otherwise svm page fault
handler will fail to recover the fault and dump GPU vm fault log.
Refactor deferred list work to get_task_mm and take mmap write lock
to handle all ranges, and avoid mm is gone while inserting mmu notifier.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Otherwise when IH process restart, count is zero, the loop will
not exit to wake_up_all after processing AMDGPU_IH_MAX_NUM_IVS
interrupts.
Cc: stable@vger.kernel.org
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Renoir and newer gfx9 APUs have new TSC register that is
not part of the gfxoff tile, so it can be read without
needing to disable gfx off.
Acked-by: Luben Tuikov <luben.tuikov@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Apply the same check we do for dGPUs for APUs as well.
Acked-by: Luben Tuikov <luben.tuikov@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes: 9f4f2c1a3524 ("drm/amd/amdgpu: fix the kfd pre_reset sequence in sriov")
For sriov XGMI configuration, the host driver will handle the hive reset,
so in guest side, the reset_sriov only be called once on one device. This will
make kfd post_reset unblanced with kfd pre_reset since kfd pre_reset already
been moved out of reset_sriov function. Move kfd post_reset out of reset_sriov
function to make them balance .
Signed-off-by: shaoyunl <shaoyun.liu@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Due to pass the wrong parameter down to the enable_stream_gating(),
it would cause the DSC of the removing stream would not be PG.
[HOW]
To pass the correct parameter down th the enable_stream_gating().
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Yi-Ling Chen <Yi-Ling.Chen2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A warning appears in the log on GPU reset for
link_enc_cfg_link_encs_assign for the following condition:
ASSERT(state->res_ctx.link_enc_cfg_ctx.link_enc_assignments[i].valid == false);
This is not expected behavior and may result in link encoders being
incorrectly assigned.
[How]
The dc->current_state is backed up into dm->cached_dc_state before
we commit 0 streams.
DC will clear link encoder assignments on the real state but the
changes won't propagate over to the copy we made before the
0 streams commit.
DC expects that link encoder assignments are *not* valid
when committing a state, so as a workaround it needs to be cleared
before passing it back into DC.
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We're only setting the flags on stream[0]'s planes so this logic fails
if we have more than one stream in the state.
This can cause a page flip timeout with multiple displays in the
configuration.
[How]
Index into the stream_status array using the stream index - it's a 1:1
mapping.
Fixes: cdaae8371aa9 ("drm/amd/display: Handle GPU reset for DC block")
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
