3504 Commits

Author SHA1 Message Date
Joachim Eastwood
d2aef35a5c serial: 8250: add LPC18xx/43xx UART driver
Serial port driver for the 8250-based UART found on LPC18xx/43xx
devices. The UART is 16550A compatible with additional features
like RS485 support, synchronous mode, IrDA, and DMA.

For now only basic UART and RS485 operation is supported.

Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-06-01 06:56:33 +09:00
Masahiro Yamada
1a8d2903cb serial: 8250_uniphier: add UniPhier serial driver
Add the driver for on-chip UART used on UniPhier SoCs.

This hardware is similar to 8250, but the register mapping is
slightly different:
  - The offset to FCR, MCR is different.
  - The divisor latch access bit does not exist.  Instead, the
    divisor latch register is available at offset 9.

This driver overrides serial_{in,out}, dl_{read,write} callbacks,
but wants to borrow most of code from 8250_core.c.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-06-01 06:55:13 +09:00
Heikki Krogerus
0788c39b95 serial: 8250_dw: support ACPI platforms with integrated DMA engine
On many new Intel SoCs the UART has an integrated DMA engine
(iDMA). In order to use it a special filter function is needed.

Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-06-01 06:55:12 +09:00
Masahiro Yamada
6f0c3091e7 serial: of_serial: check the return value of clk_prepare_enable()
The function clk_prepare_enable() may fail, and in that case it
does not make sense to proceed.  Let's check its return code and
error out if it is a negative value.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-06-01 06:55:12 +09:00
Masahiro Yamada
3a63d22425 serial: of_serial: use devm_clk_get() instead of clk_get()
The probe method of this driver calls clk_get(), but clk_put() is
missing from the remove callback.

Using the managed clk function is easier than fixing other parts.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-06-01 06:55:12 +09:00
Noam Camus
6e63be3fee serial: earlycon: Add support for big-endian MMIO accesses
Support command line parameters of the form:
earlycon=<name>,io|mmio|mmio32|mmio32be,<addr>,<options>

This commit seem to be needed even after commit:
serial: 8250: Add support for big-endian MMIO accesses
c627f2ceb692e8a9358b64ac2d139314e7bb0d17

Signed-off-by: Noam Camus <noamc@ezchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-06-01 06:55:12 +09:00
Qipan Li
0f17e3b478 serial: sirf: use hrtimer for data rx
when the serial works as a bluetooth sink, due to audio realtime
requirement, the driver should have something similar with ALSA:
1. one big DMA buffer to easy the schedule jitter
2. split this big DMA buffer to multiple small periods, for each
period, we get a DMA interrupt, then push the data to userspace.
the small periods will easy the audio latency.

so ALSA generally uses a cyclic chained DMA.

but for sirfsoc, the dma hardware has the limitation: we have
only two loops in the cyclic mode, so we can only support two
small periods to switch. if we make the DMA buffer too big, we
get long latency, if we make the DMA buffer too little, we get
miss in scheduling for audio realtime.

so this patch moves to use a hrtimer to simulate the cyclic
DMA, then we can have a big buffer, and also have a timely
data push to users as the hrtimer can generate in small period
then actual HW interrupts.

with this patch, we also delete a lot of complex codes to handle
loop buffers, and RX timeout interrupt since the RX work can be
completely handled from hrtimer interrupt.

tests show using this way will make our bad audio streaming be-
come smooth.

Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-06-01 06:51:37 +09:00
Qipan Li
86459b0e40 serial: sirf: correct the fifo empty_bit
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-06-01 06:51:37 +09:00
Qipan Li
326707ed88 serial: sirf: fix system hung on console log output
A corner case exists in the current driver. if an app opens the console
device, and before writing to console device, and there are huge kernel
ogs to print out, system will hang on
sirfsoc_uart_console_putchar:
while (rd_regl(port, ureg->sirfsoc_tx_fifo_status) &
	ufifo_st->ff_full(port->line))
	cpu_relax();
as in sirfsoc_uart_startup(), the driver assigns tx_fifo_op to 0 will stop
TX FIFO, this loop will be endless.

Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-06-01 06:51:37 +09:00
Masahiro Yamada
ba02406e9b serial: 8250: remove return statements from void function
serial8250_set_mctrl() is a void type function.  Returning something
does not look nice.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-06-01 06:48:16 +09:00
Jakub Kicinski
478d1051a0 sc16is7xx: use kworker for RS-485 configuration
RS-485 configuration is also done under the spinlock
so no blocking I/O allowed.

Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-06-01 06:47:27 +09:00
Jakub Kicinski
059d581530 sc16is7xx: use kworker to update ier bits
.stop_rx/tx() are called in atomic context, we cannot use
blocking I/O. While at it correct the name of RX bit and
'*' placement in pointer declarations.

Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-06-01 06:47:27 +09:00
Jakub Kicinski
a010408536 sc16is7xx: use kworker for md_proc
Convert md_proc into general async reconfiguration procedure.

Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-06-01 06:47:27 +09:00
Jakub Kicinski
dbe5a40cba sc16is7xx: move RTS delay to workqueue
Instead of spinning under port->lock let's just sleep
inside the kthread.  It should be equivalent as TX cannot
proceed when thread is blocked.

Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-06-01 06:47:27 +09:00
Jakub Kicinski
9e6f4ca3e5 sc16is7xx: use kthread_worker for tx_work and irq
Convert workqueue usage to a real-time kworker.  The problem
with workqueues is that we cannot set real-time priorities on
our work and asynchronous reconfiguration can be blocked by
less important tasks.

We need kthread for the interrupt anyway and because we will
now be using single kthread for all TX-related operations we
can get rid of the port mutex.

Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-06-01 06:47:27 +09:00
Jakub Kicinski
4ae82e5d23 sc16is7xx: use LSR_TEMT_BIT in .tx_empty()
LSR_TEMT_BIT (LSR bit 6) provides us exactly the information
we need to determine if transmission is finished - FIFO level
and shift register empty.  We can save ourselves reading FIFO
level explicitly if we use this bit.

Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-06-01 06:47:27 +09:00
Jakub Kicinski
4117a60c8e sc16is7xx: add missing compatible strings
Without matching bus-specific strings driver will not be loaded
automatically.

Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-06-01 06:47:27 +09:00
Jakub Kicinski
5451bb29f7 sc16is7xx: remove RS-485 delay RTS handling
Users of RS-485 can request via ioctl that RTS signals should
be activated selected number of milliseconds before the actual
data transmission or delay reception certain number of milli-
seconds after the transmission is finished.  In sc16is7xx,
however, RTS signalling is handled by the hardware and driver
has no way of providing this feature.

We still try to provide .delay_rts_before_send by delaying
transmission but without actual effect on the RTS line.

Note: this change will make the driver return -EINVAL when the
      feature is requested (.delay_rts_after_send is set).

Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-06-01 06:45:28 +09:00
Rama Kiran Kumar Indrakanti
2c837a8a8f sc16is7xx: spi interface is added
spi interface for sc16is7xx is added along with Kconfig flag
to enable spi or i2c, thus in a instance we can have either
spi or i2c or both, in sync to the hw.

Signed-off-by: Rama Kiran Kumar Indrakanti <indrakanti_ram@hotmail.com>
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-06-01 06:45:27 +09:00
Peter Senna Tschudin
07d783fd83 staging: goldfish: Fix pointer cast for 32 bits
As the first argument of gf_write64() was of type unsigned long, and as
some calls to gf_write64() were casting the first argument from void *
to u64 the compiler and/or sparse were printing warnings for casts of
wrong sizes when compiling for i386.

This patch changes the type of the first argument of gf_write64() to
const void *, and update calls to the function. This change fixed the
warnings and allowed to remove casts from 3 calls to gf_write64().

In addition gf_write64() was renamed to gf_write_ptr() as the name was
misleading because it only writes 32 bits on 32 bit systems.

gf_write_dma_addr() was added to handle dma_addr_t values which is
used at drivers/staging/goldfish/goldfish_audio.c.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-31 11:40:14 +09:00
Jan Beulich
c4ace5daf4 hvc_xen: avoid uninitialized variable warning
Older compilers don't recognize that "v" can't be used uninitialized;
other code using hvm_get_parameter() zeros the value too, so follow
suit here.

Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
2015-05-28 12:23:12 +01:00
Luis R. Rodriguez
9c27847dda kernel/params: constify struct kernel_param_ops uses
Most code already uses consts for the struct kernel_param_ops,
sweep the kernel for the last offending stragglers. Other than
include/linux/moduleparam.h and kernel/params.c all other changes
were generated with the following Coccinelle SmPL patch. Merge
conflicts between trees can be handled with Coccinelle.

In the future git could get Coccinelle merge support to deal with
patch --> fail --> grammar --> Coccinelle --> new patch conflicts
automatically for us on patches where the grammar is available and
the patch is of high confidence. Consider this a feature request.

Test compiled on x86_64 against:

	* allnoconfig
	* allmodconfig
	* allyesconfig

@ const_found @
identifier ops;
@@

const struct kernel_param_ops ops = {
};

@ const_not_found depends on !const_found @
identifier ops;
@@

-struct kernel_param_ops ops = {
+const struct kernel_param_ops ops = {
};

Generated-by: Coccinelle SmPL
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Junio C Hamano <gitster@pobox.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: cocci@systeme.lip6.fr
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
2015-05-28 11:32:10 +09:30
James Hogan
70f041b6e1 ttyFDC: Fix to use native endian MMIO reads
The MIPS Common Device Memory Map (CDMM) is internal to the core and has
native endianness. There is therefore no need to byte swap the accesses
on big endian targets, so convert the Fast Debug Channel (FDC) TTY
driver to use __raw_readl()/__raw_writel() rather than
ioread32()/iowrite32().

Fixes: 4cebec609aea ("TTY: Add MIPS EJTAG Fast Debug Channel TTY driver")
Fixes: c2d7ef51d731 ("ttyFDC: Implement KGDB IO operations.")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9905/
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2015-05-26 16:46:52 +02:00
Graeme Gregory
3db9ab0b6d drivers: PL011: add ACPI probing for SBSA UART
Add the necessary driver boilerplate to let the driver be used when
the respective ACPI table is discovered by the ACPI subsystem.

[Andre: change table name, add MODULE_DEVICE_TABLE entry and improve
	commit message]

Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Graeme Gregory <graeme.gregory@linaro.org>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Naresh Bhat <nbhat@cavium.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-24 13:08:51 -07:00
Andre Przywara
0dd1e247fd drivers: PL011: add support for the ARM SBSA generic UART
The ARM Server Base System Architecture[1] document describes a
generic UART which is a subset of the PL011 UART.
It lacks DMA support, baud rate control and modem status line
control, among other things.
The idea is to move the UART initialization and setup into the
firmware (which does this job today already) and let the kernel just
use the UART for sending and receiving characters.

We use the recent refactoring to build a new struct uart_ops
variable which points to some new functions avoiding access to the
missing registers. We reuse as much existing PL011 code as possible.

In contrast to the PL011 the SBSA UART does not define any AMBA or
PrimeCell relations, so we go with a pretty generic probe function
which only uses platform device functions.
A DT binding is provided with this patch, ACPI support is added in a
separate one.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Naresh Bhat <nbhat@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-24 13:08:51 -07:00
Andre Przywara
cefc2d1d66 drivers: PL011: allow to supply fixed option string
The SBSA UART has a fixed baud rate and flow control setting, which
cannot be changed or queried by software.
Add a vendor specific property to always return fixed values when
trying to read the console options.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Naresh Bhat <nbhat@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-24 13:08:51 -07:00
Andre Przywara
71eec4836b drivers: PL011: allow avoiding UART enabling/disabling
The SBSA UART should not be enabled or disabled (it is always on),
and consequently the spec lacks the UART_CR register.
Add a vendor specific property to skip disabling or enabling of the
UART. This will be used later by the SBSA UART support.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Naresh Bhat <nbhat@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-24 13:08:51 -07:00
Andre Przywara
9c4ef4b030 drivers: PL011: move cts_event workaround into separate function
To avoid lines with more than 80 characters and to make the
pl011_int() function more readable, move the workaround out into a
separate function.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Naresh Bhat <nbhat@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-24 13:08:51 -07:00
Andre Przywara
075167ed71 drivers: PL011: replace UART_MIS reading with _RIS & _IMSC
The PL011 register UART_MIS is actually a bitwise AND of the
UART_RIS and the UART_MISC register.
Since the SBSA UART does not include the _MIS register, use the
two separate registers to get the same behaviour. Since we are
inside the spinlock and we read the _IMSC register only once, there
should be no race issue.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Naresh Bhat <nbhat@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-24 13:08:51 -07:00
Andre Przywara
3873e2d7f6 drivers: PL011: refactor pl011_probe()
Currently the pl011_probe() function is relying on some AMBA IDs
and a device tree node to initialize the driver and a port.
Both features are not necessarily required for the driver:
- we lack AMBA IDs in the ARM SBSA generic UART and
- we lack a DT node in ACPI systems.
So lets refactor the function to ease later reuse.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Naresh Bhat <nbhat@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-24 13:08:51 -07:00
Andre Przywara
ef5a935884 drivers: PL011: refactor pl011_set_termios()
Split the pl011_set_termios() function into smaller chunks to allow
easier reuse later when adding SBSA support.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Naresh Bhat <nbhat@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-24 13:08:51 -07:00
Andre Przywara
95166a3fd5 drivers: PL011: refactor pl011_shutdown()
Split the pl011_shutdown() function into smaller chunks to allow
easier reuse later when adding SBSA support.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Naresh Bhat <nbhat@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-24 13:08:50 -07:00
Andre Przywara
867b8e8e89 drivers: PL011: refactor pl011_startup()
Split the pl011_startup() function into smaller chunks to allow
easier reuse later when adding SBSA support.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Naresh Bhat <nbhat@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-24 13:08:50 -07:00
Andre Przywara
49bb3c862c drivers: PL011: avoid potential unregister_driver call
Although we care about not unregistering the driver if there are
still ports connected during the .remove callback, we do miss this
check in the pl011_probe function. So if the current port allocation
fails, but there are other ports already registered, we will kill
those.
So factor out the port removal into a separate function and use that
in the probe function, too.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Naresh Bhat <nbhat@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-24 13:08:50 -07:00
Arnd Bergmann
7798edeebc tty: serial/8250: remove console dependency for mediatek
If the mediatek serial port driver is built-in, but serial
console is disabled in Kconfig (e.g. when the serial driver
itself is a loadable module), we get this build error:

drivers/built-in.o: In function `early_mtk8250_setup':
undefined reference to `early_serial8250_setup'

To avoid that problem, this patch encloses the early_mtk8250_setup
function in #ifdef CONFIG_SERIAL_8250_CONSOLE, the same symbol
that guards the early_serial8250_setup function.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-24 13:06:09 -07:00
Arnd Bergmann
357d561519 serial: samsung: only use earlycon for console
A configuration that enables earlycon but not the core console
code causes a link error:

  drivers/built-in.o: In function `setup_earlycon':
  drivers/tty/serial/earlycon.c:70: undefined reference to `uart_parse_earlycon'

That error can be triggered by the newly added samsung earlycon support,
which is missing a 'select' statement.

As suggested by Peter Hurley, solves the problem by moving the
'select SERIAL_EARLYCON' statement to the samsung console driver
option, as it is done by all other console drivers.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: b94ba0328d3b3 ("serial: samsung: Add support for early console")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-24 13:06:08 -07:00
Arnd Bergmann
abab381fee tty: remove platform_sysrq_reset_seq
The platform_sysrq_reset_seq code was intended as a way for an embedded
platform to provide its own sysrq sequence at compile time. After over
two years, nobody has started using it in an upstream kernel, and
the platforms that were interested in it have moved on to devicetree,
which can be used to configure the sequence without requiring kernel
changes. The method is also incompatible with the way that most
architectures build support for multiple platforms into a single
kernel.

Now the code is producing warnings when built with gcc-5.1:

drivers/tty/sysrq.c: In function 'sysrq_init':
drivers/tty/sysrq.c:959:33: warning: array subscript is above array bounds [-Warray-bounds]
   key = platform_sysrq_reset_seq[i];

We could fix this, but it seems unlikely that it will ever be used,
so let's just remove the code instead. We still have the option to
pass the sequence either in DT, using the kernel command line,
or using the /sys/module/sysrq/parameters/reset_seq file.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 154b7a489a ("Input: sysrq - allow specifying alternate reset sequence")
----
v2: moved sysrq_reset_downtime_ms variable to avoid introducing a compile
    warning when CONFIG_INPUT is disabled
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-24 13:06:08 -07:00
Uwe Kleine-König
445df7ff3f serial: mctrl-gpio: drop usages of IS_ERR_OR_NULL
The function mctrl_gpio_init returns failure if the assignment to any
member of the gpio array results in an error pointer.  So there is no
need to check for such error values in the other functions.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-24 13:06:08 -07:00
Geert Uytterhoeven
c33eecc7ab tty: Spelling s/reseved/reserved/
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-24 13:06:08 -07:00
Sebastian Andrzej Siewior
9e91597f24 serial: 8250_omap: provide complete custom startup & shutdown callbacks
The currently in-use port->startup and port->shutdown are "okay". The
startup part for instance does the tiny omap extra part and invokes
serial8250_do_startup() for the remaining pieces. The workflow in
serial8250_do_startup() is okay except for the part where UART_RX is
read without a check if there is something to read. I tried to
workaround it in commit 0aa525d11859 ("tty: serial: 8250_core: read only
RX if there is something in the FIFO") but then reverted it later in
commit ca8bb4aefb9 ("serial: 8250: Revert "tty: serial: 8250_core: read
only RX if there is something in the FIFO"").

This is the second attempt to get it to work on older OMAPs without
breaking other chips this time
Peter Hurley suggested to pull in the few needed lines from
serial8250_do_startup() and drop everything else that is not required
including making it simpler like using just request_irq() instead the
chain handler like it is doing now.
So lets try that.

Fixes: ca8bb4aefb93 ("serial: 8250: Revert "tty: serial: 8250_core:
       read only RX if there is something in the FIFO"")
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-24 12:54:55 -07:00
Jon Hunter
8f8e48f4d6 serial: tegra: Fix memory leak on DMA setup failure
If the call to dmaengine_slave_config() fails, then the DMA buffer will
not be freed/unmapped. Fix this by moving the code that stores the
address of the buffer in the tegra_uart_port structure to before the
call to dmaengine_slave_config().

Reported-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-24 12:53:44 -07:00
Qipan Li
c35b49b716 serial: sirf: assign console default index if users not set a valid one
it seems this is a more typical behaviour from reviewing other console
drivers.

Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-24 12:50:41 -07:00
Qipan Li
7f60f2fe16 serial: sirf: add serial loopback function support
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-24 12:50:41 -07:00
Qipan Li
d9e8e976fa serial: sirf: add uart receive's some error counter and mark
add overrun error's flag mark and parity's counter, we can show the
statistic from procfs node.

BTW, let the indentation of stick bits configuration look better.

Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-24 12:50:41 -07:00
Qipan Li
36c0991089 serial: sirf: fix endless loop bug in uart receive tasklet
In special condition, when cpu schedule into rx_tmo_process_tl or
rx_dma_complete_tl and all the receive dma tasks have done, it will
go into endless loop because no dma task cookie status be changed.

Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-24 12:50:41 -07:00
Qipan Li
eab192ae56 serial: sirf: fix the issue that HW flow control doesn't work for BT
>From HW spec, when rxfifo's data is less than AFC_RX_THD(RX threshhold), RTS
signal is active. otherwise, RTS signal is inactive.

Crrently the RX threshhold is set as zero, so RTS has no chance to be
active. This patch replaces the default 0 by a positive number.

Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-24 12:50:41 -07:00
Qipan Li
c1b7ac6f4d serial: sirf: enable ATLAS7 USP serial support
differentiate difference port types by re-defining the status MARCO
or putting HW differences into private data of the related ports.

Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-24 12:50:41 -07:00
Masahiro Yamada
98b3f0d535 tty: rocket: fix comment of ROCKET_SPD_HI
This comment does not reflect the actual code.  It should be 57600,
not 56000.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-24 12:49:16 -07:00
Nicolas Ferre
8687634b79 tty/serial: at91: RS485 mode: 0 is valid for delay_rts_after_send
In RS485 mode, we may want to set the delay_rts_after_send value to 0.
In the datasheet, the 0 value is said to "disable" the Transmitter Timeguard but
this is exactly the expected behavior if we want no delay...

Moreover, if the value was set to non-zero value by device-tree or earlier
ioctl command, it was impossible to change it back to zero.

Reported-by: Sami Pietikäinen <Sami.Pietikainen@wapice.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: stable@vger.kernel.org  # 3.2+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-24 12:49:16 -07:00
Mark Tomlinson
da555db6b0 n_tty: Fix calculation of size in canon_copy_from_read_buf
There was a hardcoded value of 4096 which should have been N_TTY_BUF_SIZE.
This caused reads from tty to fail with EFAULT when they shouldn't have
done if N_TTY_BUF_SIZE was declared to be something other than 4096.

Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-05-24 12:43:50 -07:00