We should check the blacklist no matter what, meaning also when we're
not connectable. This patch fixes the respective logic in the function
making the decision whether to accept a connection or not.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we have at least one LE slave connection most (probably all)
controllers will refuse to initiate any new connections. To avoid
unnecessary failures simply check for this situation up-front and skip
the connection attempt.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We need to be able to track slave vs master LE connections in
hci_conn_hash, and to be able to do that we need to know the role of the
connection by the time hci_conn_add_has() is called. This means in
practice the hci_conn_add() call that creates the hci_conn_object.
This patch adds a new role parameter to hci_conn_add() function to give
the object its initial role value, and updates the callers to pass the
appropriate role to it. Since the function now takes care of
initializing both conn->role and conn->out values we can remove some
other unnecessary assignments.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To make the code more understandable it makes sense to use the new HCI
defines for connection role instead of a "bool master" parameter. This
makes it immediately clear when looking at the function calls what the
last parameter is describing.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Having a dedicated u8 role variable in the hci_conn struct greatly
simplifies tracking of the role, since this is the native way that it's
represented on the HCI level.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
All HCI commands and events, including LE ones, use 0x00 for master role
and 0x01 for slave role. It makes therefore sense to add generic defines
for these instead of the current LE_CONN_ROLE_MASTER. Having clean
defines will also make it possible to provide simpler internal APIs.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The check for the blacklist in hci_le_conn_complete_evt() should be when
we know that we have an actual successful connection (ev->status being
non-zero). This patch fixes this ordering.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The params variable was just used for storing the return value from the
hci_pend_le_action_lookup() function and then checking whether it's NULL
or not. We can simplify the code by checking the return value directly.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we need to make the decision whether to perform just-works or real
user confirmation we need to know the exact local authentication
requirement that was passed to the controller. So far conn->auth_type
(the local requirement) wasn't in one case updated appropriately in fear
of the user confirmation being rejected later.
The real problem however was not really that conn->auth_type couldn't
represent the true value but that we were checking the local MITM
requirement in an incorrect way. It's perfectly fine to let auth_type
follow what we tell the controller since we're still tracking the target
security level with conn->pending_sec_level.
This patch updates the check for local MITM requirement in the
hci_user_confirm_request_evt function to use the locally requested
security level and ensures that auth_type always represents what we tell
the controller. All other code in hci_user_confirm_request_evt still
uses the auth_type instead of pending_sec_level for determining whether
to do just-works or not, since that's the only value that's in sync with
what the remote device knows.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Tested-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org # 3.16
The internals of the HCI request framework should not be leaking to
its users. Move them all into net/bluetooth/hci_core.c and provide
a simple hci_req_pending helper function for the one user outside
the framework.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Set Connectable/Discoverable mgmt handlers use a hci_request with a
proper callback to handle the HCI command sending. It makes therefore
little sense to have this extra function to be called from hci_event.c
for command failures.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since the HCISETSCAN ioctl is the only non-mgmt user we care about for
setting the right discoverable state we can simply do the necessary
updates in the ioctl handler function instead. This then allows the
removal of the mgmt_discoverable function and should simplify that state
handling considerably.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The mgmt_connectable function has been used to ensure that the right
actions to HCI_CONNECTABLE are taken when the HCI_Write_Scan_Enable
command is triggered by something else than mgmt. The only other user
that we really care about is the HCISETSCAN ioctl code, so we can
actually more simply perform the needed changes there instead.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for looking up entries in the white list when
HCI_CONNECTABLE is not set. The logic is fairly simple: if we're
connectable check the black list, if we're not connectable check the
white list.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The conditions for accepting an incoming connections are already
non-trivial and will become more so once a white list is added. This
patch breaks up the checks for when to reject the request by creating a
helper function for it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We already have several lists with struct bdaddr_list entries, and there
will be more in the future. Since the operations for adding, removing,
looking up and clearing entries in these lists are exactly the same it
doesn't make sense to define new functions for every single list. This
patch unifies the functions by passing the list_head to them instead of
a hci_dev pointer.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
All LE controllers always implicitly stop advertising when establishing
connections. Therefore, be sure to clear the flag in the event handler
for new LE connections.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There are many different places that can disable LE scanning but we only
want to re-enable advertising in hci_cc_le_set_scan_enable() for a very
specific use case, which is when the active scanning part of Start
Discovery is complete. Because of this, fix the discovery state check to
test for the exact state.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Many controllers allow simultaneous active scanning and advertising
(e.g. Intel and Broadcom) but some do not (e.g. CSR). It's therefore
safest to implement mutual exclusion of these states in the kernel.
This patch ensures that the two states are never entered simultaneously.
Extra precaution needs to be taken for outgoing connection attempts in
slave role (i.e. through directed advertising) in which case the
operation that came first has precedence and the one that comes after
gets a rejection.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since the real advertising state is now tracked with its own flag we can
simply set/unset the HCI_ADVERTISING flag in the
set_advertising_complete function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Having a single HCI_ADVERTISING flag is problematic since it tries to
track both the real advertising state and the corresponding mgmt
setting. To make the logic simpler and more reliable add a new flag that
only tracks the actual advertising state that has been written to the
controller.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If we have both LE scanning and advertising simultaneously enabled we
need a way to tell hci_connect_le() in which role to initiate a
connection. This patch adds a new parameter to the function to give it
the necessary information. For auto-connect and mgmt_pair_device we
always use master role, whereas for L2CAP users (in practice sockets) we
use slave role whenever HCI_ADVERTISING is set and master role
otherwise.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The auth_type value which gets assigned to hci_conn->auth_type is
something that's only used for BR/EDR connections and is of no value for
LE connections. It makes therefore little sense to pass it to the
hci_connect_le() function. This patch removes the parameter from the
function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since the only caller of this function doesn't care about the return
value anymore let's just remove it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If we have devices set as to be connected we should connect to them even
during normal discovery if we get a connectable advertising event. If we
also have HCI_CONNECTABLE set we should connect ADV_DIRECT_IND events
even to devices that we don't have in our pend_le_conns list. This patch
implements such behavior by passing the advertising report type to
check_pending_le_conn() and calls that function regardless of what type
of scanning we are doing.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we get an LE connection complete event we should restart background
scanning if there are any devices needing it. So far the code was only
making the decision based on whether the completed connection had any
stored parameters or not. This patch ensures that we trigger background
scanning always when necessary.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we establish connections as a consequence of receiving an
advertising report it makes no sense to wait the normal 20 second LE
connection timeout. This patch modifies the hci_connect_le function to
take an extra timeout value and uses a lower 2 second timeout for the
auto-connection case. This timeout is intentionally chosen to be just a
bit higher than the 1.28 second timeout that High Duty Cycle Advertising
uses.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
During the setup phase of a controller, the Bluetooth address will be
read and to have that original address available for later use, store
it as setup address.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The HCI event callbacks have grown over the last years and some
functions handle status checking different than others. For the
simple ones, check the status at the beginning and exit if an
error with the HCI command occured.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If a found device is marked as blocked while doing passive LE scanning,
neither report it nor try to connect to it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Instead of looking through the entire list of entries we can more
efficiently use the new hci_pend_le_action_lookup() function to look up
entries specifically in the pend_le_reports list. Since the search is
now limited to the right list we can also remove an unnecessary check
for list_empty() before the lookup.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In some circumstances we need to look up entries in pend_le_conns and in
other in pend_le_reports. This patch converts the existing lookup
function for pend_le_conns to something that can be used for both lists.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This is the last place using hci_pend_le_conn_add() and we can more
just as simply manipulate the list directly here.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since params->action is used for both the pend_le_conns and
pend_le_reports lists we can simplify the adding and deleting of the
lists considerably. For example, when deleting entries in most
situations we no-longer need to check the auto_connect value but can
directly proceed with calling list_del_init on param->action (which is
safe even if the entry is not part of any list).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To simplify manipulation and lookup of hci_conn_params entries of the
type HCI_AUTO_CONN_REPORT it makes sense to store them in their own
list. The new action list_head in hci_conn_params is used for this
purpose.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If we're doing passive scanning we shouldn't proceed with any of the
code that deals with active scanning (pending reports, etc.). This patch
fixes a missing return statement for the passive scanning section in the
process_adv_report() function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since we only store entries with identity addresses in the
le_conn_params and pend_le_conns lists we can avoid unnecessary lookups
by checking for an identity address before diving into the lists
themselves.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If a device is in the pend_le_conns list it cannot at the same time also
have the need to be notified through mgmt_device_found. By making
check_pending_le_conn return whether it found an entry or not we can
avoid unnecessary checks in process_adv_report().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since the connection parameters are always a basis for adding entries to
hdev->pend_le_conns (so far of type bdaddr_list) it's simpler and more
efficient to have the parameters themselves be the entries in the
pend_le_conns list. We do this by adding another list_head to the
hci_conn_params struct.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When processing passive scanning results we need the resolved identity
address both in check_pending_le_conn() as well as later in
process_adv_report(). Since process_adv_report() calls
check_pending_le_conn() we can simply resolve the IRK earlier in the
function and thereby eliminate a second lookup.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we're scanning for specific devices that use an RPA we need to
convert the RPA to the identity address before looking up the entry in
the connection parameters. This patch adds the necessary code to do this
in the process_adv_report() function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If we have one or more devices with HCI_AUTO_CONN_REPORT we should do
background scanning and emit mgmt_device_found events. This patch
modifies the hci_update_background_scan() function to extend the
conditions needed to trigger scanning, and adds the necessary code to
process_adv_report() to emit mgmt_device_found events.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The calling functions of mgmt_new_conn_param have more information about
the parameters, such as whether the kernel is tracking them or not. It
makes therefore sense to have them pass an initial store_hint value to
the mgmt_new_conn_param function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We should update any stored connection parameters when we receive the LE
Remote Connection Parameter Request HCI event. This patch adds the
necessary code to the function that handles the event.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Unlike BR/EDR we cannot reject LE connections of blocked devices but
have to do it as soon as we get a LE Connection Complete event. The
patch adds a blacklist check to the hci_le_conn_complete_evt function
and drops all connections for blocked devices.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduces a new Mgmt event called "New Connection Parameter".
This event indicates to userspace the connection parameters values the
remote device requested.
The user may store these values and load them into kernel. This way, next
time a connection is established to that device, the kernel will use those
parameters values instead of the default ones.
This event is sent when the remote device requests new connection
parameters through connection parameter update procedure. This event is
not sent for slave connections.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for LE Connection Parameters Request Link
Layer control procedure introduced in Core spec 4.1. This procedure
allows a Peripheral or Central to update the Link Layer connection
parameters of an established connection.
Regarding the acceptance of connection parameters, the LL procedure
follows the same approach of L2CAP procedure (see l2cap_conn_param_
update_req function). We accept any connection parameters values as
long as they are within the valid range.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There are certain subtle differences in behavior when we're encrypted
with the STK, such as allowing re-encryption even though the security
level stays the same. Because of this, add a flag to track whether we're
encrypted with an STK or not.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Device Found events of the management interface should indicate if
it is possible to connect to a remote device or if it is broadcaster
only advertising. To allow this differentation the Not Connectable flag
is introduced that will be set when it is known that a device can not
be connected.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Providing the flags parameter directly to mgmt_device_found function
makes the core simpler and more readable. With this it becomes a lot
easier to add new flags in the future.
This also changes hci_inquiry_cache_update to just return that flags
needed for mgmt_device_found since that is its only use for the two
return parameters anyway.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
