Before going to backup mode architecture specific PM code sets the first
word in securam (file arch/arm/mach-at91/pm.c, function at91_pm_begin()).
Thus take this into account when suspending/resuming clocks. This will
avoid executing unnecessary instructions when suspending to non backup
modes.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20211011112719.3951784-3-claudiu.beznea@microchip.com
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
SAMA5D2 and SAMA7G5 have a special power saving mode (backup mode) where
most of the SoC's components are powered off (including PMC). Resuming
from this mode is done with the help of bootloader. Peripherals are not
aware of the power saving mode thus most of them are disabling clocks in
proper suspend API and re-enable them in resume API without taking into
account the previously setup rate. Moreover some of the peripherals are
acting as wakeup sources and are not disabling the clocks in this
scenario, when suspending. Since backup mode cuts the power for
peripherals, in resume part these clocks needs to be re-configured.
The initial PMC suspend/resume code was designed only for SAMA5D2's PMC
(as it was the only one supporting backup mode). SAMA7G supports also
backup mode and its PMC is different (few new functionalities, different
registers offsets, different offsets in registers for each
functionalities). To address both SAMA5D2 and SAMA7G5 PMC add
.save_context()/.resume_context() support to each clocks driver and call
this from PMC driver.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20211011112719.3951784-2-claudiu.beznea@microchip.com
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Currently, at91 pmc driver always register the syscore_ops whatever
the status of the pmc node that has been found. When set as secure
and disabled, the pmc should not be accessed or this will generate
abort exceptions.
To avoid this, add a check on node availability before registering
the syscore operations.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Link: https://lore.kernel.org/r/20210913082633.110168-1-clement.leger@bootlin.com
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Fixes: b3b02eac33ed ("clk: at91: Add sama5d2 suspend/resume")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
On clk_generated_determine_rate(), the requested rate could be outside
of clk's range. Limit the rate to the clock's range to not return an
error.
Fixes: df70aeef6083 ("clk: at91: add generated clock driver")
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20210707131213.3283509-1-codrin.ciubotariu@microchip.com
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Remove all "/**" kernel-doc markers from sama7g5.c since they are
all internal to this driver source file only.
This eliminates 14 warnings that were reported by the kernel test robot.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: linux-clk@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Link: https://lore.kernel.org/r/20210819223237.20115-1-rdunlap@infradead.org
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
These are all "early clocks" that require initialization just at
of_clk_init() time. Use CLK_OF_DECLARE() to declare them.
This also fixes a problem that was spotted when fw_devlink was
set to 'on' by default: the boards failed to boot. The reason is
that CLK_OF_DECLARE_DRIVER() clears the OF_POPULATED and causes
the consumers of the clock to be postponed by fw_devlink until
the second initialization routine of the clock has been completed.
One of the consumers of the clock is the timer, which is used as a
clocksource, and needs the clock initialized early. Postponing the
timers caused the fail at boot.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20210203154332.470587-1-tudor.ambarus@microchip.com
Acked-by: Saravana Kannan <saravanak@google.com>
Tested-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Register CPU clock as being the master clock prescaler. This would
be used by DVFS. The block schema of SAMA7G5's PMC contains also a divider
between master clock prescaler and CPU (PMC_CPU_RATIO.RATIO) but the
frequencies supported by SAMA7G5 could be directly received from
CPUPLL + master clock prescaler and the extra divider would do no work in
case it would be enabled.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1605800597-16720-12-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Re-factor master clock driver by splitting it into 2 clocks: prescaller
and divider clocks. Based on registered clock flags the prescaler's rate
could be changed at runtime. This is necessary for platforms supporting
DVFS (e.g. SAMA7G5) where master clock could be changed at run-time.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1605800597-16720-11-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Since CPU PLL feeds both CPU clock and MCK0, MCK0 cannot go higher
than 200MHz and MCK0 maximum prescaller is 5 limit the CPU PLL at
1GHz to avoid MCK0 overclocking while CPU PLL is changed by DVFS.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1605800597-16720-10-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
On SAMA7G5 CPU clock is changed at run-time by DVFS. Since MCK0 and
CPU clock shares the same parent clock (CPUPLL clock) the MCK0 is
also changed by DVFS to avoid over/under clocking of MCK0 consumers.
The lower limit is changed to be able to set MCK0 accordingly by
DVFS.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1605800597-16720-9-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
MCK0 is changed at runtime by DVFS. Due to this, since not all IPs
are glitch free aware at MCK0 changes, remove MCK0 from parent list
of other clocks (e.g. generic clock, programmable/system clock, MCKX).
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1605800597-16720-8-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This SoC has the 5th divisor for the mck0 master clock.
Adapt the characteristics accordingly.
Reported-by: Mihai Sain <mihai.sain@microchip.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1605800597-16720-6-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
clk-master can have 5 divisors with a field width of 3 bits
on some products.
Change the mask and number of divisors accordingly.
Reported-by: Mihai Sain <mihai.sain@microchip.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1605800597-16720-5-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Allow SYSPLL and CPUPLL to be referenced as a PMC_TYPE_CORE clock
from phandle in DT.
Suggested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
[claudiu.beznea@microchip.com: adapt commit message, add CPU PLL]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1605800597-16720-4-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add SAMA7G5 specific PLL defines to be referenced in a phandle as a
PMC_TYPE_CORE clock.
Suggested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
[claudiu.beznea@microchip.com: adapt comit message, adapt sama7g5.c]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1605800597-16720-3-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
pmc_data_allocate() has been changed. pmc_data_free() was removed.
Adapt the code taking this into consideration. With this the programmable
clocks were also saved in sama7g5_pmc so that they could be later
referenced.
Fixes: cb783bbbcf54 ("clk: at91: sama7g5: add clock support for sama7g5")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/1605800597-16720-2-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
- Support qcom SM8150/SM8250 video and display clks
- Change how qcom's display port clks work
* clk-ingenic:
clk: ingenic: Respect CLK_SET_RATE_PARENT in .round_rate
clk: ingenic: Don't tag custom clocks with CLK_SET_RATE_PARENT
clk: ingenic: Don't use CLK_SET_RATE_GATE for PLL
clk: ingenic: Use readl_poll_timeout instead of custom loop
clk: ingenic: Use to_clk_info() macro for all clocks
* clk-at91:
clk: at91: sam9x60: support only two programmable clocks
clk: at91: clk-sam9x60-pll: remove unused variable
clk: at91: clk-main: update key before writing AT91_CKGR_MOR
clk: at91: remove the checking of parent_name
* clk-kconfig:
clk: Restrict CLK_HSDK to ARC_SOC_HSDK
* clk-imx:
clk: imx8mq: Fix usdhc parents order
clk: imx: imx21: Remove clock driver
clk: imx: gate2: Fix a few typos
clk: imx: Fix and update kerneldoc
clk: imx: fix i.MX7D peripheral clk mux flags
clk: imx: fix composite peripheral flags
clk: imx: Correct the memrepair clock on imx8mp
clk: imx: Correct the root clk of media ldb on imx8mp
clk: imx: vf610: Add CRC clock
clk: imx: Explicitly include bits.h
clk: imx8qxp: Support building i.MX8QXP clock driver as module
clk: imx8m: Support module build
clk: imx: Add clock configuration for ARMv7 platforms
clk: imx: Support building i.MX common clock driver as module
clk: composite: Export clk_hw_register_composite()
clk: imx6sl: Use BIT(x) to avoid shifting signed 32-bit value by 31 bits
* clk-qcom:
clk: qcom: gdsc: Keep RETAIN_FF bit set if gdsc is already on
clk: qcom: Add display clock controller driver for SM8150 and SM8250
dt-bindings: clock: add QCOM SM8150 and SM8250 display clock bindings
clk: qcom: add video clock controller driver for SM8250
clk: qcom: add video clock controller driver for SM8150
dt-bindings: clock: add SM8250 QCOM video clock bindings
dt-bindings: clock: add SM8150 QCOM video clock bindings
dt-bindings: clock: combine qcom,sdm845-videocc and qcom,sc7180-videocc
clk: qcom: gcc-msm8994: Add missing clocks, resets and GDSCs
clk/qcom: fix spelling typo
clk: qcom: gcc-sdm660: Fix wrong parent_map
clk: qcom: dispcc: Update DP clk ops for phy design
clk: qcom: gcc-msm8939: remove defined but not used variables
clk: qcom: ipq8074: make pcie0_rchng_clk_src static
* clk-prima2:
clk: clk-prima2: fix return value check in prima2_clk_init()
* clk-bcm:
clk: bcm2835: add missing release if devm_clk_hw_register fails
clk: bcm: rpi: Add register to control pixel bvb clk
According to datasheet (Chapter 29.16.13, PMC Programmable Clock Register)
there are only two programmable clocks on SAM9X60.
Fixes: 01e2113de9a5 ("clk: at91: add sam9x60 pmc driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1602686072-28296-1-git-send-email-claudiu.beznea@microchip.com
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fix variable set but not used compilation warning.
Fixes: 43b1bb4a9b3e ("clk: at91: clk-sam9x60-pll: re-factor to support plls with multiple outputs")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1598338751-20607-4-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
SAMA5D2 datasheet specifies on chapter 33.22.8 (PMC Clock Generator
Main Oscillator Register) that writing any value other than
0x37 on KEY field aborts the write operation. Use the key when
selecting main clock parent.
Fixes: 27cb1c2083373 ("clk: at91: rework main clk implementation")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1598338751-20607-3-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
There is no need to check parent_name variable while assigning it to
init.parent_names. parent_name variable is already checked at
the beginning of at91_clk_register_peripheral() function.
Fixes: 6114067e437eb ("clk: at91: add PMC peripheral clocks")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1598338751-20607-2-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The at91sam9g45_pcr_layout is not used so drop it to fix build warning:
drivers/clk/at91/at91sam9g45.c:49:36: warning:
'at91sam9g45_pcr_layout' defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200916161740.14173-1-krzk@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add UTMI support for SAMA7G5. SAMA7G5's UTMI control is done via
XTALF register. Values written at bits 2..0 in this register
correspond to the on board crystal oscillator frequency.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1595403506-8209-18-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Some of the SAMA7G5 PLLs support multiple outputs (e.g. AUDIO PLL).
For these, split the PLL clock in two: fractional clock and
divider clock. In case PLLs supports multiple outputs (since these
outputs are dividers (with different settings) sharing the same
fractional part), it will register one fractional clock and multiple
divider clocks (dividers sharing the fractional clock).
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1595403506-8209-17-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Some peripheral clocks on SAMA7G5 supports requesting parent to change
its rate (image related clocks: csi, csi2dc, isc). Add support
so that if registered with this option the clock rate to be
requested from parent.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1595403506-8209-14-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add master clock support (MCK1..4) for SAMA7G5. SAMA7G5's PMC has
multiple master clocks feeding different subsystems. One of them
feeds image subsystem and is changeable based on image subsystem
needs.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1595403506-8209-13-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Pass the ID of changeable parent at registration. This will allow
the scalability of this clock driver with regards to the changeable
parent ID for versions of this IP where changeable parent is not the
last one in the parents list (e.g. SAMA7G5). With this the clock flags
are set to zero in case we have no changeable parent. Also in
clk_generated_best_diff() the *best_diff variable is check against
tmp_diff variable using ">=" operator instead of ">" so that in case
the requested frequency could be obtained using fix parents + gck
dividers but the clock also supports changeable parent to be able
to force the usage of the changeable parent.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1595403506-8209-11-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
In commit a436c2a447e59 ("clk: at91: add sam9x60 PLL driver")
the fractional part of PLL wasn't set on registers but it was
calculated and taken into account for determining div and mul
(see sam9x60_pll_get_best_div_mul()).
Fixes: a436c2a447e59 ("clk: at91: add sam9x60 PLL driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1595403506-8209-7-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
According to datasheet the range of 600-1200MHz is for the
frequency generated by the fractional part of the PLL (namely
Fcorepllck according to datasheet). With this in mind the output
range of the PLL itself (fractional + div), taking into account
that the divider is 8 bits wide, is 600/256-1200Hz=2.3-1200MHz.
Fixes: a436c2a447e59 ("clk: at91: add sam9x60 PLL driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1595403506-8209-6-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Use logical or for range check. In case bestrate is not in
characteristics->output[0].min..characteristics->output[0].max
range we should return -ERANGE.
Fixes: a436c2a447e59 ("clk: at91: add sam9x60 PLL driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1595403506-8209-5-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
__clk_determine_rate() may return error. Skip the current step
in case of error.
Fixes: 1a1a36d72e3d3 ("clk: at91: clk-generated: make gclk determine audio_pll rate")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1595403506-8209-2-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
syscon_node_to_regmap() will make the created regmap get and enable the
first clock it can parse from the device tree. This clock is not needed to
access the registers and should not be enabled at that time.
Use device_node_to_regmap to resolve this as it looks up the regmap in
the same list but doesn't care about the clocks. This issue is detected
by lockdep when booting the sama5d3 with a device tree containing the
new clk bindings.
This fix already happened in 6956eb33abb5 ("clk: at91: fix possible
deadlock") for the drivers that had been migrated to the new clk binding
back then. This does the same for the new drivers as well.
Fixes: 01e2113de9a5 ("clk: at91: add sam9x60 pmc driver")
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Link: https://lore.kernel.org/r/20200703073236.23923-1-a.fatoum@pengutronix.de
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
We need to have clocks accessible via phandle to select them
as peripheral clock parent using assigned-clock-parents in DT.
Add support for PLLACK/PLLBCK/AUDIOPLLCK clocks where available.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lkml.kernel.org/r/fa39cc10dab8341ea4bc2b7152be9217b2cd34a5.1588630999.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
