The device release number for HX-type devices is configurable in
EEPROM/OTPROM and cannot be used reliably for type detection.
Assume all (non-H) devices with bcdUSB 1.1 and unknown bcdDevice to be
of HX type while adding a bcdDevice check for HXD and TB (1.1 and 2.0,
respectively).
Reported-by: Chris <chris@cyber-anlage.de>
Fixes: 8a7bf7510d1f ("USB: serial: pl2303: amend and tighten type detection")
Cc: stable@vger.kernel.org # 5.13
Link: https://lore.kernel.org/r/20210730122156.718-1-johan@kernel.org
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The chip supports high transfer rates, but with the small default buffers
(64 bytes read), some entire blocks are regularly lost. This typically
happens at 1.5 Mbps (which is the default speed on Rockchip devices) when
used as a console to access U-Boot where the output of the "help" command
misses many lines and where "printenv" mangles the environment.
The FTDI driver doesn't suffer at all from this. One difference is that
it uses 512 bytes rx buffers and 256 bytes tx buffers. Adopting these
values completely resolved the issue, even the output of "dmesg" is
reliable. I preferred to leave the Tx value unchanged as it is not
involved in this issue, while a change could increase the risk of
triggering the same issue with other devices having too small buffers.
I verified that it backports well (and works) at least to 5.4. It's of
low importance enough to be dropped where it doesn't trivially apply
anymore.
Cc: stable@vger.kernel.org
Signed-off-by: Willy Tarreau <w@1wt.eu>
Link: https://lore.kernel.org/r/20210724152739.18726-1-w@1wt.eu
Signed-off-by: Johan Hovold <johan@kernel.org>
put_tty_driver() is an alias for tty_driver_kref_put(). There is no need
for two exported identical functions, therefore switch all users of
old put_tty_driver() to new tty_driver_kref_put() and remove the former
for good.
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Cc: Jens Taprogge <jens.taprogge@taprogge.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Scott Branden <scott.branden@broadcom.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: David Lin <dtwlin@gmail.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Alex Elder <elder@kernel.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: David Sterba <dsterba@suse.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Acked-by: Alex Elder <elder@linaro.org>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: David Sterba <dsterba@suse.com>
Acked-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210723074317.32690-8-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
alloc_tty_driver was deprecated by tty_alloc_driver in commit
7f0bc6a68ed9 (TTY: pass flags to alloc_tty_driver) in 2012.
I never got into eliminating alloc_tty_driver until now. So we still
have two functions for allocating drivers which might be confusing. So
get rid of alloc_tty_driver uses to eliminate it for good in the next
patch.
Note we need to switch return value checking as tty_alloc_driver uses
ERR_PTR. And flags are now a parameter of tty_alloc_driver.
Cc: Richard Henderson <rth@twiddle.net>(odd fixer:ALPHA PORT)
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Cc: Jens Taprogge <jens.taprogge@taprogge.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: David Sterba <dsterba@suse.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Johan Hovold <johan@kernel.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Acked-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: David Sterba <dsterba@suse.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210723074317.32690-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the USB serial device ID for the CEL ZigBee EM3588 radio stick.
Signed-off-by: John Keeping <john@metanate.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
The driver core ignores the return value of this callback because there
is only little it can do when a device disappears.
This is the final bit of a long lasting cleanup quest where several
buses were converted to also return void from their remove callback.
Additionally some resource leaks were fixed that were caused by drivers
returning an error code in the expectation that the driver won't go
away.
With struct bus_type::remove returning void it's prevented that newly
implemented buses return an ignored error code and so don't anticipate
wrong expectations for driver authors.
Reviewed-by: Tom Rix <trix@redhat.com> (For fpga)
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Cornelia Huck <cohuck@redhat.com> (For drivers/s390 and drivers/vfio)
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> (For ARM, Amba and related parts)
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org> (for sunxi-rsb)
Acked-by: Pali Rohár <pali@kernel.org>
Acked-by: Mauro Carvalho Chehab <mchehab@kernel.org> (for media)
Acked-by: Hans de Goede <hdegoede@redhat.com> (For drivers/platform)
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Acked-by: Juergen Gross <jgross@suse.com> (For xen)
Acked-by: Lee Jones <lee.jones@linaro.org> (For mfd)
Acked-by: Johannes Thumshirn <jth@kernel.org> (For mcb)
Acked-by: Johan Hovold <johan@kernel.org>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> (For slimbus)
Acked-by: Kirti Wankhede <kwankhede@nvidia.com> (For vfio)
Acked-by: Maximilian Luz <luzmaximilian@gmail.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> (For ulpi and typec)
Acked-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com> (For ipack)
Acked-by: Geoff Levand <geoff@infradead.org> (For ps3)
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com> (For thunderbolt)
Acked-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> (For intel_th)
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net> (For pcmcia)
Acked-by: Rafael J. Wysocki <rafael@kernel.org> (For ACPI)
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org> (rpmsg and apr)
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> (For intel-ish-hid)
Acked-by: Dan Williams <dan.j.williams@intel.com> (For CXL, DAX, and NVDIMM)
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com> (For isa)
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (For firewire)
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> (For hid)
Acked-by: Thorsten Scherer <t.scherer@eckelmann.de> (For siox)
Acked-by: Sven Van Asbroeck <TheSven73@gmail.com> (For anybuss)
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> (For MMC)
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Finn Thain <fthain@linux-m68k.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20210713193522.1770306-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix comments for GE CS1000 CP210x USB ID assignments.
Fixes: 42213a0190b5 ("USB: serial: cp210x: add some more GE USB IDs")
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
The patch is meant to support LARA-R6 Cat 1 module family.
Module USB ID:
Vendor ID: 0x05c6
Product ID: 0x90fA
Interface layout:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: QMI wwan (not available in all versions)
Signed-off-by: Marco De Marco <marco.demarco@posteo.net>
Link: https://lore.kernel.org/r/49260184.kfMIbaSn9k@mars
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Here is the big set of USB and Thunderbolt patches for 5.14-rc1.
Nothing major here just lots of little changes for new hardware and
features. Highlights are:
- more USB 4 support added to the thunderbolt core
- build warning fixes all over the place
- usb-serial driver updates and new device support
- mtu3 driver updates
- gadget driver updates
- dwc3 driver updates
- dwc2 driver updates
- isp1760 host driver updates
- musb driver updates
- lots of other tiny things.
Full details are in the shortlog.
All of these have been in linux-next for a while now with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYOM3EA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynGewCeMg7YvtCnqFBNebC+GfKpFTgWxO4AnAppjSrZ
RPGQgfZdWmx7daCXWbSK
=u68a
-----END PGP SIGNATURE-----
Merge tag 'usb-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt patches for 5.14-rc1.
Nothing major here just lots of little changes for new hardware and
features. Highlights are:
- more USB 4 support added to the thunderbolt core
- build warning fixes all over the place
- usb-serial driver updates and new device support
- mtu3 driver updates
- gadget driver updates
- dwc3 driver updates
- dwc2 driver updates
- isp1760 host driver updates
- musb driver updates
- lots of other tiny things.
Full details are in the shortlog.
All of these have been in linux-next for a while now with no reported
issues"
* tag 'usb-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (223 commits)
phy: qcom-qusb2: Add configuration for SM4250 and SM6115
dt-bindings: phy: qcom,qusb2: document sm4250/6115 compatible
dt-bindings: usb: qcom,dwc3: Add bindings for sm6115/4250
USB: cdc-acm: blacklist Heimann USB Appset device
usb: xhci-mtk: allow multiple Start-Split in a microframe
usb: ftdi-elan: remove redundant continue statement in a while-loop
usb: class: cdc-wdm: return the correct errno code
xhci: remove redundant continue statement
usb: dwc3: Fix debugfs creation flow
usb: gadget: hid: fix error return code in hid_bind()
usb: gadget: eem: fix echo command packet response issue
usb: gadget: f_hid: fix endianness issue with descriptors
Revert "USB: misc: Add onboard_usb_hub driver"
Revert "of/platform: Add stubs for of_platform_device_create/destroy()"
Revert "usb: host: xhci-plat: Create platform device for onboard hubs in probe()"
Revert "arm64: dts: qcom: sc7180-trogdor: Add nodes for onboard USB hub"
xhci: solve a double free problem while doing s4
xhci: handle failed buffer copy to URB sg list and fix a W=1 copiler warning
xhci: Add adaptive interrupt rate for isoch TRBs with XHCI_AVOID_BEI quirk
xhci: Remove unused defines for ERST_SIZE and ERST_ENTRIES
...
Here are the USB-serial updates for 5.14-rc1, including:
- gpio support for CP2108
- chars_in_buffer and write_room return-value updates
- chars_in_buffer and write_room clean ups
Included are also various clean ups.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCYNRHtQAKCRALxc3C7H1l
CD96AQDYFm0ssrdV61bejQLX+9LrIfNuISXNJy9cLhCxi3ZYJwD/ZLJhz0K/Xby1
+Xm4J5UVbPuIKMkNKMc0ezH0XZfURwU=
=61V6
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.14-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for 5.14-rc1
Here are the USB-serial updates for 5.14-rc1, including:
- gpio support for CP2108
- chars_in_buffer and write_room return-value updates
- chars_in_buffer and write_room clean ups
Included are also various clean ups.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.14-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: cp210x: add support for GPIOs on CP2108
USB: serial: drop irq-flags initialisations
USB: serial: mos7840: drop buffer-callback return-value comments
USB: serial: mos7720: drop buffer-callback sanity checks
USB: serial: io_edgeport: drop buffer-callback sanity checks
USB: serial: digi_acceleport: add chars_in_buffer locking
USB: serial: digi_acceleport: reduce chars_in_buffer over-reporting
USB: serial: make usb_serial_driver::chars_in_buffer return uint
USB: serial: make usb_serial_driver::write_room return uint
Similar to some other CP210x device types, CP2108 has a number of GPIO
pins that can be exposed through gpiolib.
CP2108 has four serial interfaces but only one set of GPIO pins, which
is modelled as a single gpio chip and registered as a child of the first
interface.
CP2108 has 16 GPIOs so the width of the state variables needs to be
extended to 16 bits and this is also reflected in the control requests.
Like CP2104, CP2108 have GPIO pins with configurable alternate
functions and pins unavailable for GPIO use are determined and reported
to gpiolib at probe.
Signed-off-by: Pho Tran <pho.tran@silabs.com>
Co-developed-by: Tung Pham <tung.pham@silabs.com>
Signed-off-by: Tung Pham <tung.pham@silabs.com>
[ johan: rewrite gpio get() and set(); misc cleanups; amend commit
message ]
Link: https://lore.kernel.org/r/20210610132844.25495-1-johan@kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
In the previous patch, we introduced tty_get_char_size() and
tty_get_frame_size() for computing character and frame sizes,
respectively. Here, we make use of them in various tty drivers where
applicable.
The stats look nice: 12 insertions, 169 deletions.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Lin <dtwlin@gmail.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Alex Elder <elder@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Oliver Neukum <oneukum@suse.com>
Acked-by: Alex Elder <elder@kernel.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210610090247.2593-4-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make data_bits what it really is. Assign proper bit counts to data_bits
instead of magic 0..3. There are two reasons:
1) it's clear what we store there, and
2) it will make the transition to tty_tty_get_char_size() in the next
patch easier.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210610090247.2593-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmDGe+4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG/IUH/iyHVulAtAhL9bnR
qL4M1kWfcG1sKS2TzGRZzo6YiUABf89vFP90r4sKxG3AKrb8YkTwmJr8B/sWwcsv
PpKkXXTobbDfpSrsXGEapBkQOE7h2w739XeXyBLRPkoCR4UrEFn68TV2rLjMLBPS
/EIZkonXLWzzWalgKDP4wSJ7GaQxi3LMx3dGAvbFArEGZ1mPHNlgWy2VokFY/yBf
qh1EZ5rugysc78JCpTqfTf3fUPK2idQW5gtHSMbyESrWwJ/3XXL9o1ET3JWURYf1
b0FgVztzddwgULoIGWLxDH5WWts3l54sjBLj0yrLUlnGKA5FjrZb12g9PdhdywuY
/8KfjeE=
=JfJm
-----END PGP SIGNATURE-----
Merge tag 'v5.13-rc6' into tty-next
We want the tty fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CP2102N revision A01 (firmware version <= 1.0.4) has a buggy
flow-control implementation that uses the ulXonLimit instead of
ulFlowReplace field of the flow-control settings structure (erratum
CP2102N_E104).
A recent change that set the input software flow-control limits
incidentally broke RTS control for these devices when CRTSCTS is not set
as the new limits would always enable hardware flow control.
Fix this by explicitly disabling flow control for the buggy firmware
versions and only updating the input software flow-control limits when
IXOFF is requested. This makes sure that the terminal settings matches
the default zero ulXonLimit (ulFlowReplace) for these devices.
Link: https://lore.kernel.org/r/20210609161509.9459-1-johan@kernel.org
Reported-by: David Frey <dpfrey@gmail.com>
Reported-by: Alex Villacís Lasso <a_villacis@palosanto.com>
Tested-by: Alex Villacís Lasso <a_villacis@palosanto.com>
Fixes: f61309d9c96a ("USB: serial: cp210x: set IXOFF thresholds")
Cc: stable@vger.kernel.org # 5.12
Signed-off-by: Johan Hovold <johan@kernel.org>
The QFN20 part has a different GPIO/port function assignment. The
configuration struct bit field ordered as TX/RX/RS485/WAKEUP/CLK
which exactly matches GPIO0-3 for QFN24/28. However, QFN20 has a
different GPIO to primary function assignment.
Special case QFN20 to follow to properly detect which GPIOs are
available.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Link: https://lore.kernel.org/r/51830b2b24118eb0f77c5c9ac64ffb2f519dbb1d.1622218300.git.stefan@agner.ch
Fixes: c8acfe0aadbe ("USB: serial: cp210x: implement GPIO support for CP2102N")
Cc: stable@vger.kernel.org # 4.19
Signed-off-by: Johan Hovold <johan@kernel.org>
Add PID for the NovaTech OrionMX so it can be automatically detected.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
With the inclusion of Omni 56K Plus, this driver seem to be more common
among the family of Zyxel omni modem. Update the driver and module
descriptions.
Signed-off-by: Alexandre GRIVEAUX <agriveaux@deutnet.info>
[ johan: amend commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Add device id for Zyxel Omni 56K Plus modem, this modem include:
USB chip:
NetChip
NET2888
Main chip:
901041A
F721501APGF
Another modem using the same chips is the Zyxel Omni 56K DUO/NEO,
could be added with the right USB ID.
Signed-off-by: Alexandre GRIVEAUX <agriveaux@deutnet.info>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
The direction of the pipe argument must match the request-type direction
bit or control requests may fail depending on the host-controller-driver
implementation.
Fix the three requests which erroneously used usb_rcvctrlpipe().
Fixes: f7a33e608d9a ("USB: serial: add quatech2 usb to serial driver")
Cc: stable@vger.kernel.org # 3.5
Signed-off-by: Johan Hovold <johan@kernel.org>
There's no need to initialise irq-flags variables before saving the
interrupt state.
Drop the redundant initialisations from the three drivers that got this
wrong.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The driver write_room and chars_in_buffer callbacks used to incorrectly
return a negative errno in case they were called with a NULL port
driver-data pointer or if some other always-true sanity checks failed.
The bogus sanity checks were later removed by commit ce039bd4b21f ("USB:
serial: mos7840: drop paranoid port checks") and 7b2faede671a ("USB:
serial: mos7840: drop port driver data accessors") but the
function-header comments were never updated to match.
Drop the outdated return-value comments.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The driver write_room and chars_in_buffer callbacks used to incorrectly
return a negative errno in case they were ever called with a NULL port
driver-data pointer. The return value was later changed to zero by
commit 23198fda7182 ("tty: fix chars_in_buffers") but the bogus sanity
checks were left in place as were the outdated function-header comments.
The port driver data isn't cleared until after the port has been
deregistered and all open ttys have been hung up so drop the unnecessary
sanity checks and the outdated comments.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The driver write_room and chars_in_buffer callbacks used to incorrectly
return a negative errno in case they were called while or after the port
had been closed. The return value was later changed to zero by commit
d76f2f4462bb ("io_edgeport: Fix various bogus returns to the tty
layer") but the bogus sanity checks were left in place as were the
outdated function-header comments.
These callbacks will never be called for an uninitialised port so drop
the unnecessary sanity checks and the outdated comments.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Both the dp_write_urb_in_use flag and dp_out_buf_len counter should be
accessed while holding the driver port lock. Add the missing locking to
chars_in_buffer and clean up the implementation somewhat by using a
common exit path.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Due to an ancient quirk in n_tty poll implementation, the
digi_acceleport driver has been reporting that its queue contains 256
(WAKEUP_CHARS) characters whenever its write URB is in use.
This has not been necessary since 2003 when the line-discipline started
taking the write room into account so let's return the maximum transfer
size again in order to over-report a little less and incidentally fix
the related debug statement.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
tty_operations::chars_in_buffer is being switched to return uint. Do the
same for usb_serial_driver's chars_in_buffer.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
[ johan: amend commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Line disciplines expect a positive value or zero returned from
tty->ops->write_room (invoked by tty_write_room). Both of them are being
updated to return an unsigned int. Switch also
usb_serial_driver::write_room and all its users.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
[ johan: amend commit message, drop unrelated comment change ]
Signed-off-by: Johan Hovold <johan@kernel.org>
tty_operations::chars_in_buffer is another hook which is expected to
return values >= 0. So make it explicit by the return type too -- use
unsigned int.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-By: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Acked-by: David Sterba <dsterba@suse.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Cc: Jens Taprogge <jens.taprogge@taprogge.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: David Lin <dtwlin@gmail.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Alex Elder <elder@kernel.org>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Link: https://lore.kernel.org/r/20210505091928.22010-27-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Line disciplines expect a positive value or zero returned from
tty->ops->write_room (invoked by tty_write_room). So make this
assumption explicit by using unsigned int as a return value. Both of
tty->ops->write_room and tty_write_room.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Acked-by: Alex Elder <elder@linaro.org>
Acked-by: Max Filippov <jcmvbkbc@gmail.com> # xtensa
Acked-by: David Sterba <dsterba@suse.com>
Acked-By: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Chris Zankel <chris@zankel.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Cc: Jens Taprogge <jens.taprogge@taprogge.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Scott Branden <scott.branden@broadcom.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: David Lin <dtwlin@gmail.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Link: https://lore.kernel.org/r/20210505091928.22010-23-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds the device id for the ADLINK ND-6530 which is a PL2303GC based
device.
Signed-off-by: Zolton Jheng <s6668c2t@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
This adds support for the Startech.com generic serial to USB converter.
It seems to be a bone stock TI_3410. I have been using this patch for
years.
Signed-off-by: Sean MacLennan <seanm@seanm.ca>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Add the IDS GmbH Vendor ID and the Product IDs for SI31A (2xRS232)
and CM31A (LoRaWAN Modem).
Signed-off-by: Dominik Andreas Schorpp <dominik.a.schorpp@ids.de>
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Here is the big set of USB and Thunderbolt driver updates for 5.13-rc1.
Lots of little things in here, with loads of tiny fixes and cleanups
over these drivers, as well as these "larger" changes:
- thunderbolt updates and new features added
- xhci driver updates and split out of a mediatek-specific xhci
driver from the main xhci module to make it easier to work
with (something that I have been wanting for a while).
- loads of typec feature additions and updates
- dwc2 driver updates
- dwc3 driver updates
- gadget driver fixes and minor updates
- loads of usb-serial cleanups and fixes and updates
- usbip documentation updates and fixes
- lots of other tiny USB driver updates
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYIa42A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymMEACgkQBzLb5W/IocS+oq7+D7P3V581sAn1Dcy2Qq
Yz370/X2hrjXAyIm7/Cz
=5dj/
-----END PGP SIGNATURE-----
Merge tag 'usb-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB and Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt driver updates for
5.13-rc1.
Lots of little things in here, with loads of tiny fixes and cleanups
over these drivers, as well as these "larger" changes:
- thunderbolt updates and new features added
- xhci driver updates and split out of a mediatek-specific xhci
driver from the main xhci module to make it easier to work with
(something that I have been wanting for a while).
- loads of typec feature additions and updates
- dwc2 driver updates
- dwc3 driver updates
- gadget driver fixes and minor updates
- loads of usb-serial cleanups and fixes and updates
- usbip documentation updates and fixes
- lots of other tiny USB driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (371 commits)
usb: Fix up movement of USB core kerneldoc location
usb: dwc3: gadget: Handle DEV_TXF_FLUSH_BYPASS capability
usb: dwc3: Capture new capability register GHWPARAMS9
usb: gadget: prevent a ternary sign expansion bug
usb: dwc3: core: Do core softreset when switch mode
usb: dwc2: Get rid of useless error checks in suspend interrupt
usb: dwc2: Update dwc2_handle_usb_suspend_intr function.
usb: dwc2: Add exit hibernation mode before removing drive
usb: dwc2: Add hibernation exiting flow by system resume
usb: dwc2: Add hibernation entering flow by system suspend
usb: dwc2: Allow exit hibernation in urb enqueue
usb: dwc2: Move exit hibernation to dwc2_port_resume() function
usb: dwc2: Move enter hibernation to dwc2_port_suspend() function
usb: dwc2: Clear GINTSTS_RESTOREDONE bit after restore is generated.
usb: dwc2: Clear fifo_map when resetting core.
usb: dwc2: Allow exiting hibernation from gpwrdn rst detect
usb: dwc2: Fix hibernation between host and device modes.
usb: dwc2: Fix host mode hibernation exit with remote wakeup flow.
usb: dwc2: Reset DEVADDR after exiting gadget hibernation.
usb: dwc2: Update exit hibernation when port reset is asserted
...
Reset the transmit and receive FIFOs before enabling the UARTs as part
of open() in order to flush any stale data.
Note that the XR21V141X needs a type-specific implementation due to its
UART Manager registers.
Signed-off-by: Johan Hovold <johan@kernel.org>
The XR22801, XR22802 and XR22804 are compound devices with an embedded
hub and up to seven downstream USB devices including one, two or four
UARTs respectively.
The UART function is similar to XR21B142X but most registers are offset
by 0x40, the register requests are different and are directed at the
device rather than interface, and 5 and 6-bit words are not supported.
Signed-off-by: Johan Hovold <johan@kernel.org>
The single-port XR21B1411 is similar to the XR21B142X type but uses
12-bit registers and 16-bit register addresses, the register requests
are different and are directed at the device rather than interface, and
5 and 6-bit words are not supported.
The register layout is very similar to XR21B142X except that most
registers are offset by 0xc00 (corresponding to a channel index of 12 in
the MSB of wIndex). As the device is single-port so that the derived
channel index is 0, the current register accessors can be reused after
simply changing the address width.
Signed-off-by: Johan Hovold <johan@kernel.org>
The XR21B1421, XR21B1422 and XR21B1424 are the one-, two- and four-port
models of a second XR21B142X type of the Maxlinear/Exar USB UARTs.
The XR21B142X type differs from XR21V141X in several ways, including:
- register layout
- register width (16-bit instead of 8-bit)
- vendor register requests
- UART enable/disable sequence
- custom-driver mode flag
- three additional GPIOs (9 instead of 6)
As for XR21V141X, the XR21B142X vendor requests encode the channel index
in the MSB of wIndex, but it lacks the UART Manager registers which
have been replaced by regular UART registers. The new type also uses the
interface number of the control interface (0, 2, 4, 6) as channel index
instead of the channel number (0, 1, 2, 3).
The XR21B142X lacks the divisor and format registers used by XR21V141X
and instead uses the CDC SET_LINE_CONTROL request to configure the line
settings.
Note that the currently supported XR21V141X type lacks the custom-driver
mode flag that prevents the device from entering CDC-ACM mode when a CDC
requests is received. This specifically means that the SET_LINE_CONTROL
request cannot be used with XR21V141X even though it is otherwise
supported.
The UART enable sequence for XR21B142X does not involve explicitly
enabling the FIFOs, but according to datasheet the UART must be disabled
when writing any register but GPIO_SET, GPIO_CLEAR, TX_BREAK and
ERROR_STATUS.
Signed-off-by: Johan Hovold <johan@kernel.org>
There are at least four types of Maxlinear/Exar USB UARTs which differ
in various ways such as in their register layouts:
XR21V141X
XR21B142X
XR21B1411
XR22804
It is not clear whether the device type can be inferred from the
descriptors so encode it in the device-id table for now.
Add a type structure that can be used to abstract the register layout
and other features, and use it when accessing the XR21V141X UART
registers that are shared by all types.
Note that the currently supported XR21V141X type is the only type that
has a set of UART Manager registers and that these will need to be
handled specifically.
Similarly, XR21V141X is the only type which has the divisor registers
and that needs to use the format register when configuring the line
settings.
Signed-off-by: Johan Hovold <johan@kernel.org>
In preparation for adding support for further types, drop the type
prefix from defines that are not specific to XR21V141X.
Signed-off-by: Johan Hovold <johan@kernel.org>
There's no need to configure the pins on every open and judging from the
vendor driver and datasheet it can be done before enabling the UART.
Move pin configuration from open() to port probe and make sure to
deassert DTR and RTS after configuring all pins as GPIO.
Signed-off-by: Johan Hovold <johan@kernel.org>
Add support for the two- and four-port variants of XR21V1410.
Use the interface number of each control interface (e.g. 0, 2, 4, 6) to
derive the zero-based channel index:
XR21V1410 0
XR21V1412 0, 1
XR21V1414 0, 1, 2, 3
Note that the UART registers reside in separate blocks per channel,
while the UART Manager functionality is implemented using per-channel
registers.
Signed-off-by: Johan Hovold <johan@kernel.org>
Remove the random white space from the CSIZE switch.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
