The entire bus (PERIC) on which the GS101 serial resides only allows
32-bit register accesses. The reg-io-width dt property is disallowed
for the "google,gs101-uart" compatible and instead the iotype is
inferred from the compatible. Always set UPIO_MEM32 iotype for the
gs101 earlycon.
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20240119104526.1221243-6-tudor.ambarus@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GS101's Connectivity Peripheral blocks (peric0/1 blocks) which
include the I3C and USI (I2C, SPI, UART) only allow 32-bit
register accesses.
Instead of specifying the reg-io-width = 4 everywhere, for each node,
the requirement should be deduced from the compatible.
Infer UPIO_MEM32 iotype from the "google,gs101-uart" compatible.
Update the uart info name to be GS101 specific in order to
differentiate from the other exynos platforms. All the other settings
are not changed.
exynos_fifoszdt_serial_drv_data was replaced by gs101_serial_drv_data
because the iotype restriction is gs101 specific and there was no other
user of exynos_fifoszdt_serial_drv_data.
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20240119104526.1221243-5-tudor.ambarus@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GS101's Connectivity Peripheral blocks (peric0/1 blocks) which
include the I3C and USI (I2C, SPI, UART) only allow 32-bit
register accesses. If using 8-bit register accesses, a SError
Interrupt is raised causing the system unusable.
Instead of specifying the reg-io-width = 4 everywhere, for each node,
the requirement should be deduced from the compatible.
Prepare the samsung tty driver to allow IO types different than
UPIO_MEM. ``struct uart_port::iotype`` is an unsigned char where all
its 8 bits are exposed to uapi. We can't make NULL checks on it to
verify if it's set, thus always set it from the driver's data.
Use u8 for the ``iotype`` member of ``struct s3c24xx_uart_info`` to
emphasize that the iotype is an 8 bit mask.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20240119104526.1221243-4-tudor.ambarus@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The core expects for tx_empty() either TIOCSER_TEMT when the tx is
empty or 0 otherwise. s3c24xx_serial_txempty_nofifo() might return
0x4, and at least uart_get_lsr_info() tries to clear exactly
TIOCSER_TEMT (BIT(1)). Fix tx_empty() to return TIOCSER_TEMT.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20240119104526.1221243-2-tudor.ambarus@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix indentation and add line after do/while() block.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240118152213.2644269-18-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add comments about I2C slave address structure, and reformat to
improve readability.
Also reformat some comments according to kernel coding style.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240118152213.2644269-17-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following checkpatch warnings:
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
With this change, the affected functions now match the prototypes in
struct gpio_chip.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240118152213.2644269-16-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify driver by defining a common function to handle the power
control of all variants.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240118152213.2644269-15-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify driver by defining a common function to handle the detection
of all variants.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240118152213.2644269-14-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GENMASK() is preferred when defining bitmasks.
Of all the masks changed, only MAX310x_REV_MASK is actually used.
No functional change.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240118152213.2644269-13-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace dev_err() with dev_err_probe().
This helps in simplifing code and standardizing the error output.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240118152213.2644269-12-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allows to simplify code by removing the break statement in the default
switch/case in some functions.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240118152213.2644269-11-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify error handling and only call uart_remove_one_port() if line bit
is set, instead of having to manually set s->p[i].port.dev to NULL.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240118152213.2644269-10-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use a separate regmap name for each port so they can each have their own
debugfs entry, allowing to access each port registers independently.
For example, a four channels/ports device like the MAX14830 will have four
entries in its regmap debugfs:
$ find /sys/kernel/debug/regmap -type d | grep spi0.0
/sys/kernel/debug/regmap/spi0.0-port0
/sys/kernel/debug/regmap/spi0.0-port1
/sys/kernel/debug/regmap/spi0.0-port2
/sys/kernel/debug/regmap/spi0.0-port3
Cc: Jan Kundrát <jan.kundrat@cesnet.cz>
Link: https://lore.kernel.org/all/77f101f1-897d-4e6d-a8fd-27b818caf768@cesnet.cz/
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240118152213.2644269-9-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Running pahole shows that there are some holes within the
max310x_devtype structure.
Remove holes and optimize alignment by reorganizing structure members.
This can also lead to data structure size reduction for some CPUs.
On 64-bit CPU (arm64):
Before:
/* size: 40, cachelines: 1, members: 6 */
/* sum members: 34, holes: 2, sum holes: 6 */
/* last cacheline: 40 bytes */
After:
/* size: 40, cachelines: 1, members: 6 */
/* padding: 6 */
/* last cacheline: 40 bytes */
On 32-bit CPU (i386):
Before:
/* size: 32, cachelines: 1, members: 6 */
/* sum members: 26, holes: 2, sum holes: 6 */
/* last cacheline: 32 bytes */
After:
/* size: 24, cachelines: 1, members: 8 */
/* padding: 2 */
/* last cacheline: 24 bytes */
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240118152213.2644269-7-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace g with q.
Helpful when grepping thru source code or logs for
"request" keyword.
Fixes: f65444187a ("serial: New serial driver MAX310X")
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240118152213.2644269-6-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use preferred spi_get_device_match_data() instead of
device_get_match_data() and spi_get_device_id() to get the driver match
data.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240118152213.2644269-5-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use preferred i2c_get_match_data() instead of device_get_match_data()
to get the driver match data.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240118152213.2644269-4-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This allows to instantiate a max14830 I2C device from userspace.
Helpful when testing driver with i2c-stub.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240118152213.2644269-3-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When trying to instantiate a max14830 device from userspace:
echo max14830 0x60 > /sys/bus/i2c/devices/i2c-2/new_device
we get the following error:
Unable to handle kernel NULL pointer dereference at virtual address...
...
Call trace:
max310x_i2c_probe+0x48/0x170 [max310x]
i2c_device_probe+0x150/0x2a0
...
Add check for validity of devtype to prevent the error, and abort probe
with a meaningful error message.
Fixes: 2e1f2d9a9b ("serial: max310x: implement I2C support")
Cc: stable@vger.kernel.org
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240118152213.2644269-2-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since STM32MP25, FIFO size could vary regarding the STM32MPxx version.
So we get this size from "hwcfgr1" register and compute threshold values
corresponding to the ratio given by reference manual.
As STM32MP1x, STM32MP25 and STM32H7 share the same compatible and STM32H7
doesn't have a register to get FIFO size, we force FIFO size to 16 in case
of zero read from hwcfgr1 register.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20240112095300.2004878-5-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USART has registers above 0xff offset, so extend variable type to u16.
And change UNDEF_REG to 0xffff.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20240112095300.2004878-4-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
STM32MP25x got 9 instances of U(S)ART. So extend STM32_MAX_PORTS to 9, in
order to handle all instances.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20240112095300.2004878-3-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the case of high USART input clock and low baud rate, BRR value
is not enough to get correct baud rate. So here we use USART prescaler to
divide USART input clock to get the correct baud rate.
PRESC register is only available since stm32h7.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20240112095300.2004878-2-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The config HW_CONSOLE is always identical to the config VT and is not
visible in the kernel's build menuconfig. So, CONFIG_HW_CONSOLE is
redundant.
Replace all references to CONFIG_HW_CONSOLE with CONFIG_VT and remove
CONFIG_HW_CONSOLE.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20240108134102.601-1-lukas.bulwahn@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As of commit d7402513c9 ("arm64: smp: IPI_CPU_STOP and
IPI_CPU_CRASH_STOP should try for NMI"), if we've got pseudo-NMI
enabled then we'll use it to stop CPUs at panic time. This is nice,
but it does mean that there's a pretty good chance that we'll end up
stopping a CPU while it holds the port lock for the console
UART. Specifically, I see a CPU get stopped while holding the port
lock nearly 100% of the time on my sc7180-trogdor based Chromebook by
enabling the "buddy" hardlockup detector and then doing:
sysctl -w kernel.hardlockup_all_cpu_backtrace=1
sysctl -w kernel.hardlockup_panic=1
echo HARDLOCKUP > /sys/kernel/debug/provoke-crash/DIRECT
UART drivers are _supposed_ to handle this case OK and this is why
UART drivers check "oops_in_progress" and only do a "trylock" in that
case. However, before we enabled pseudo-NMI to stop CPUs it wasn't a
very well-tested situation.
Now that we're testing the situation a lot, it can be seen that the
Qualcomm GENI UART driver is pretty broken. Specifically, when I run
my test case and look at the console output I just see a bunch of
garbled output like:
[ 201.069084] NMI backtrace[ 201.069084] NM[ 201.069087] CPU: 6
PID: 10296 Comm: dnsproxyd Not tainted 6.7.0-06265-gb13e8c0ede12
#1 01112b9f14923cbd0b[ 201.069090] Hardware name: Google Lazor
([ 201.069092] pstate: 80400009 (Nzcv daif +PAN -UAO -TCO -DI[
201.069095] pc : smp_call_function_man[ 201.069099]
That's obviously not so great. This happens because each call to the
console driver exits after the data has been written to the FIFO but
before it's actually been flushed out of the serial port. When we have
multiple calls into the console one after the other then (if we can't
get the lock) each call tells the UART to throw away any data in the
FIFO that hadn't been transferred yet.
I've posted up a patch to change the arm64 core to avoid this
situation most of the time [1] much like x86 seems to do, but even if
that patch lands the GENI driver should still be fixed.
>From testing, it appears that we can just delete the cancel/abort in
the case where we weren't able to get the UART lock and the output
looks good. It makes sense that we'd be able to do this since that
means we'll just call into __qcom_geni_serial_console_write() and
__qcom_geni_serial_console_write() looks much like
qcom_geni_serial_poll_put_char() but with a loop. However, it seems
safest to poll the FIFO and make sure it's empty before our
transfer. This should reliably make sure that we're not
interrupting/clobbering any existing transfers.
As part of this change, we'll also avoid re-setting up a TX at the end
of the console write function if we weren't able to get the lock,
since accessing "port->tx_remaining" without the lock is not
safe. This is only needed to re-start userspace initiated transfers.
[1] https://lore.kernel.org/r/20231207170251.1.Id4817adef610302554b8aa42b090d57270dc119c@changeid
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20240112150307.2.Idb1553d1d22123c377f31eacb4486432f6c9ac8d@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vc_translate_unicode() and vc_sanitize_unicode() parse input to the
UTF-8-enabled console, marking invalid byte sequences and producing Unicode
codepoints. The current algorithm follows ancient Unicode and may accept
invalid byte sequences, pass on non-existent codepoints and reject valid
sequences.
The patch restores the functions' compliance with modern Unicode (v15.1 [1]
+ many previous versions) as well as RFC 3629 [2].
1. Codepoint space is limited to 0x10FFFF.
2. "Noncharacters", such as U+FFFE, U+FFFF, are no longer invalid in
Unicode and will be accepted. Another option was to complete the set of
noncharacters (used to be just those two, now there's more) and preserve
the rejection step. This is indeed what Unicode suggests ([1] chap.
23.7) (not requires), but most codepoints are !iswprint(), so selecting
just the noncharacters seemed arbitrary and futile (and unnecessary).
This is not a security patch. I'm not aware of any present security
implications of the old code.
[1] https://www.unicode.org/versions/Unicode15.1.0
[2] https://datatracker.ietf.org/doc/html/rfc3629
Signed-off-by: Roman Žilka <roman.zilka@gmail.com>
Link: https://lore.kernel.org/r/598ab459-6ba9-4a17-b4a1-08f26a356fc0@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In linflex_config_port() the member variable type will be
assigned again. Remove redundant uart type assignment from
linflex_probe().
Signed-off-by: Lizhe <sensor1010@163.com>
Link: https://lore.kernel.org/r/20240112133923.190852-1-sensor1010@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
receive_buf() is called from ttyport_receive_buf() that expects values
">= 0" from serdev_controller_receive_buf(), change its return type from
ssize_t to size_t.
The need for this clean-up was noticed while fixing a warning, see
commit 94d0539425 ("Bluetooth: btnxpuart: fix recv_buf() return value").
Changing the callback prototype to return an unsigned seems the best way
to document the API and ensure that is properly used.
GNSS drivers implementation of serdev receive_buf() callback return
directly the return value of gnss_insert_raw(). gnss_insert_raw()
returns a signed int, however this is not an issue since the value
returned is always positive, because of the kfifo_in() implementation.
gnss_insert_raw() could be changed to return also an unsigned, however
this is not implemented here as request by the GNSS maintainer Johan
Hovold.
Suggested-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/all/087be419-ec6b-47ad-851a-5e1e3ea5cfcc@kernel.org/
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> #for-iio
Reviewed-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Acked-by: Maximilian Luz <luzmaximilian@gmail.com> # for platform/surface
Acked-by: Lee Jones <lee@kernel.org>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240122180551.34429-1-francesco@dolcini.it
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
selection.c and vt.c still uses tabs in the kernel-doc. This misrenders the
functions in the output -- sphinx misinterprets the description. So
remove these tabs, incl. those around dashes.
'enum' keyword is needed before enum names. Fix that.
Superfluous \n after the comments are also removed. They are not
completely faulty, but this unifies all the kernel-doc in the files.
Finally fix up the cross references.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Helge Deller <deller@gmx.de> # parisc STI console
Link: https://lore.kernel.org/r/20240122110401.7289-47-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the previous patch, nobody sets that hook. So drop it completely.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Tested-by: Helge Deller <deller@gmx.de> # parisc STI console
Link: https://lore.kernel.org/r/20240122110401.7289-44-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* parameter offset: it is expected to be non-negative, so switch to
unsigned
* return type: switch from ushort to explicit u16. This is expected on
most places. And fix the remaining two places too.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Tested-by: Helge Deller <deller@gmx.de> # parisc STI console
Link: https://lore.kernel.org/r/20240122110401.7289-42-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the previous patch, nobody sets that hook. So drop it completely.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Tested-by: Helge Deller <deller@gmx.de> # parisc STI console
Link: https://lore.kernel.org/r/20240122110401.7289-41-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-1 is the same as VESA_VSYNC_SUSPEND in all con_blank() implementations.
So we can remove this special case from vgacon now too.
Despite con_blank() of fbcon looks complicated, the "if
(!fbcon_is_inactive(vc, info))" branch is not taken as we set
"ops->graphics = 1;" few lines above. So what matters there (as in all
other blank implementations except vgacon) is if 'blank' is zero or not.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: Helge Deller <deller@gmx.de>
Cc: linux-fbdev@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Tested-by: Helge Deller <deller@gmx.de> # parisc STI console
Link: https://lore.kernel.org/r/20240122110401.7289-32-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The non-zero (true) return value from consw::con_switch() means a redraw
is needed. So make this return type a bool explicitly instead of int.
The latter might imply that -Eerrors are expected. They are not.
And document the hook.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: Helge Deller <deller@gmx.de>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: linux-fbdev@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linux-parisc@vger.kernel.org
Tested-by: Helge Deller <deller@gmx.de> # parisc STI console
Link: https://lore.kernel.org/r/20240122110401.7289-31-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no difference between CM_MOVE and CM_DRAW. Either of them
enables the cursor. CM_ERASE then disables cursor.
So get rid of all of them and use simple "bool enable".
Note that this propagates down to the fbcon code.
And document the hook.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: Helge Deller <deller@gmx.de>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: linux-fbdev@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linux-parisc@vger.kernel.org
Tested-by: Helge Deller <deller@gmx.de> # parisc STI console
Link: https://lore.kernel.org/r/20240122110401.7289-30-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
And let it call consw::con_putc() if it exists, otherwise
consw::con_putcs(). This is similar to tty_put_char().
It supports dropping unneeded duplication of code like sticon_putc() is
(see the next patch).
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Tested-by: Helge Deller <deller@gmx.de> # parisc STI console
Link: https://lore.kernel.org/r/20240122110401.7289-24-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In consw::con_clear():
* Height is always 1, so drop it.
* Offsets and width are always unsigned values, so re-type them as such.
This needs a new __fbcon_clear() in the fbcon code to still handle
height which might not be 1 when called internally.
Note that tests for negative count/width are left in place -- they are
taken care of in the next patches.
And document the hook.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: Helge Deller <deller@gmx.de>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: linux-fbdev@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linux-parisc@vger.kernel.org
Tested-by: Helge Deller <deller@gmx.de> # parisc STI console
Link: https://lore.kernel.org/r/20240122110401.7289-22-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'init' parameter of consw::con_init() is true for the first call of
the hook on a particular console. So make the parameter a bool.
And document the hook.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Helge Deller <deller@gmx.de>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: linux-fbdev@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linux-parisc@vger.kernel.org
Tested-by: Helge Deller <deller@gmx.de> # parisc STI console
Link: https://lore.kernel.org/r/20240122110401.7289-21-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The return value of con_debug_enter() and con_debug_leave() is ignored
on many fronts. So just don't propagate errors (the current
implementations return 0 anyway) and make the return type a void.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Helge Deller <deller@gmx.de>
Cc: linux-fbdev@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Tested-by: Helge Deller <deller@gmx.de> # parisc STI console
Link: https://lore.kernel.org/r/20240122110401.7289-20-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I didn't find definitions for ascii in the kernel yet, so define it for
non-printable characters used here.
Note we use ' ' instead of 32 on one line too.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Tested-by: Helge Deller <deller@gmx.de> # parisc STI console
Link: https://lore.kernel.org/r/20240122110401.7289-18-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The count to process is supposed to be between 1 and vc->vc_cols -
vc->state.x (or rows and .y). clamp() can be used exactly for this,
instead of ifs and min().
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Tested-by: Helge Deller <deller@gmx.de> # parisc STI console
Link: https://lore.kernel.org/r/20240122110401.7289-14-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
