Some drivers can't dynamically change the VLAN filtering option, or
impose some restrictions, it would be nice to propagate this info
through netlink instead of printing it to a kernel log that might never
be read. Also netlink extack includes the module that emitted the
message, which means that it's easier to figure out which ones are
driver-generated errors as opposed to command misuse.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow drivers to communicate their restrictions to user space directly,
instead of printing to the kernel log. Where the conversion would have
been lossy and things like VLAN ID could no longer be conveyed (due to
the lack of support for printf format specifier in netlink extack), I
chose to keep the messages in full form to the kernel log only, and
leave it up to individual driver maintainers to move more messages to
extack.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As explained in commit 54a0ed0df496 ("net: dsa: provide an option for
drivers to always receive bridge VLANs"), DSA has historically been
skipping VLAN switchdev operations when the bridge wasn't in
vlan_filtering mode, but the reason why it was doing that has never been
clear. So the configure_vlan_while_not_filtering option is there merely
to preserve functionality for existing drivers. It isn't some behavior
that drivers should opt into. Ideally, when all drivers leave this flag
set, we can delete the dsa_port_skip_vlan_configuration() function.
New drivers always seem to omit setting this flag, for some reason. So
let's reverse the logic: the DSA core sets it by default to true before
the .setup() callback, and legacy drivers can turn it off. This way, new
drivers get the new behavior by default, unless they explicitly set the
flag to false, which is more obvious during review.
Remove the assignment from drivers which were setting it to true, and
add the assignment to false for the drivers that didn't previously have
it. This way, it should be easier to see how many we have left.
The following drivers: lan9303, mv88e6060 were skipped from setting this
flag to false, because they didn't have any VLAN offload ops in the
first place.
The Broadcom Starfighter 2 driver calls the common b53_switch_alloc and
therefore also inherits the configure_vlan_while_not_filtering=true
behavior.
Also, print a message through netlink extack every time a VLAN has been
skipped. This is mildly annoying on purpose, so that (a) it is at least
clear that VLANs are being skipped - the legacy behavior in itself is
confusing, and the extack should be much more difficult to miss, unlike
kernel logs - and (b) people have one more incentive to convert to the
new behavior.
No behavior change except for the added prints is intended at this time.
$ ip link add br0 type bridge vlan_filtering 0
$ ip link set sw0p2 master br0
[ 60.315148] br0: port 1(sw0p2) entered blocking state
[ 60.320350] br0: port 1(sw0p2) entered disabled state
[ 60.327839] device sw0p2 entered promiscuous mode
[ 60.334905] br0: port 1(sw0p2) entered blocking state
[ 60.340142] br0: port 1(sw0p2) entered forwarding state
Warning: dsa_core: skipping configuration of VLAN. # This was the pvid
$ bridge vlan add dev sw0p2 vid 100
Warning: dsa_core: skipping configuration of VLAN.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210115231919.43834-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It should be the driver's business to logically separate its VLAN
offloading into a preparation and a commit phase, and some drivers don't
need / can't do this.
So remove the transactional shim from DSA and let drivers propagate
errors directly from the .port_vlan_add callback.
It would appear that the code has worse error handling now than it had
before. DSA is the only in-kernel user of switchdev that offloads one
switchdev object to more than one port: for every VLAN object offloaded
to a user port, that VLAN is also offloaded to the CPU port. So the
"prepare for user port -> check for errors -> prepare for CPU port ->
check for errors -> commit for user port -> commit for CPU port"
sequence appears to make more sense than the one we are using now:
"offload to user port -> check for errors -> offload to CPU port ->
check for errors", but it is really a compromise. In the new way, we can
catch errors from the commit phase that we previously had to ignore.
But we have our hands tied and cannot do any rollback now: if we add a
VLAN on the CPU port and it fails, we can't do the rollback by simply
deleting it from the user port, because the switchdev API is not so nice
with us: it could have simply been there already, even with the same
flags. So we don't even attempt to rollback anything on addition error,
just leave whatever VLANs managed to get offloaded right where they are.
This should not be a problem at all in practice.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since the introduction of the switchdev API, port attributes were
transmitted to drivers for offloading using a two-step transactional
model, with a prepare phase that was supposed to catch all errors, and a
commit phase that was supposed to never fail.
Some classes of failures can never be avoided, like hardware access, or
memory allocation. In the latter case, merely attempting to move the
memory allocation to the preparation phase makes it impossible to avoid
memory leaks, since commit 91cf8eceffc1 ("switchdev: Remove unused
transaction item queue") which has removed the unused mechanism of
passing on the allocated memory between one phase and another.
It is time we admit that separating the preparation from the commit
phase is something that is best left for the driver to decide, and not
something that should be baked into the API, especially since there are
no switchdev callers that depend on this.
This patch removes the struct switchdev_trans member from switchdev port
attribute notifier structures, and converts drivers to not look at this
member.
In part, this patch contains a revert of my previous commit 2e554a7a5d8a
("net: dsa: propagate switchdev vlan_filtering prepare phase to
drivers").
For the most part, the conversion was trivial except for:
- Rocker's world implementation based on Broadcom OF-DPA had an odd
implementation of ofdpa_port_attr_bridge_flags_set. The conversion was
done mechanically, by pasting the implementation twice, then only
keeping the code that would get executed during prepare phase on top,
then only keeping the code that gets executed during the commit phase
on bottom, then simplifying the resulting code until this was obtained.
- DSA's offloading of STP state, bridge flags, VLAN filtering and
multicast router could be converted right away. But the ageing time
could not, so a shim was introduced and this was left for a further
commit.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Reviewed-by: Linus Walleij <linus.walleij@linaro.org> # RTL8366RB
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The call path of a switchdev VLAN addition to the bridge looks something
like this today:
nbp_vlan_init
| __br_vlan_set_default_pvid
| | |
| | br_afspec |
| | | |
| | v |
| | br_process_vlan_info |
| | | |
| | v |
| | br_vlan_info |
| | / \ /
| | / \ /
| | / \ /
| | / \ /
v v v v v
nbp_vlan_add br_vlan_add ------+
| ^ ^ | |
| / | | |
| / / / |
\ br_vlan_get_master/ / v
\ ^ / / br_vlan_add_existing
\ | / / |
\ | / / /
\ | / / /
\ | / / /
\ | / / /
v | | v /
__vlan_add /
/ | /
/ | /
v | /
__vlan_vid_add | /
\ | /
v v v
br_switchdev_port_vlan_add
The ranges UAPI was introduced to the bridge in commit bdced7ef7838
("bridge: support for multiple vlans and vlan ranges in setlink and
dellink requests") (Jan 10 2015). But the VLAN ranges (parsed in br_afspec)
have always been passed one by one, through struct bridge_vlan_info
tmp_vinfo, to br_vlan_info. So the range never went too far in depth.
Then Scott Feldman introduced the switchdev_port_bridge_setlink function
in commit 47f8328bb1a4 ("switchdev: add new switchdev bridge setlink").
That marked the introduction of the SWITCHDEV_OBJ_PORT_VLAN, which made
full use of the range. But switchdev_port_bridge_setlink was called like
this:
br_setlink
-> br_afspec
-> switchdev_port_bridge_setlink
Basically, the switchdev and the bridge code were not tightly integrated.
Then commit 41c498b9359e ("bridge: restore br_setlink back to original")
came, and switchdev drivers were required to implement
.ndo_bridge_setlink = switchdev_port_bridge_setlink for a while.
In the meantime, commits such as 0944d6b5a2fa ("bridge: try switchdev op
first in __vlan_vid_add/del") finally made switchdev penetrate the
br_vlan_info() barrier and start to develop the call path we have today.
But remember, br_vlan_info() still receives VLANs one by one.
Then Arkadi Sharshevsky refactored the switchdev API in 2017 in commit
29ab586c3d83 ("net: switchdev: Remove bridge bypass support from
switchdev") so that drivers would not implement .ndo_bridge_setlink any
longer. The switchdev_port_bridge_setlink also got deleted.
This refactoring removed the parallel bridge_setlink implementation from
switchdev, and left the only switchdev VLAN objects to be the ones
offloaded from __vlan_vid_add (basically RX filtering) and __vlan_add
(the latter coming from commit 9c86ce2c1ae3 ("net: bridge: Notify about
bridge VLANs")).
That is to say, today the switchdev VLAN object ranges are not used in
the kernel. Refactoring the above call path is a bit complicated, when
the bridge VLAN call path is already a bit complicated.
Let's go off and finish the job of commit 29ab586c3d83 by deleting the
bogus iteration through the VLAN ranges from the drivers. Some aspects
of this feature never made too much sense in the first place. For
example, what is a range of VLANs all having the BRIDGE_VLAN_INFO_PVID
flag supposed to mean, when a port can obviously have a single pvid?
This particular configuration _is_ denied as of commit 6623c60dc28e
("bridge: vlan: enforce no pvid flag in vlan ranges"), but from an API
perspective, the driver still has to play pretend, and only offload the
vlan->vid_end as pvid. And the addition of a switchdev VLAN object can
modify the flags of another, completely unrelated, switchdev VLAN
object! (a VLAN that is PVID will invalidate the PVID flag from whatever
other VLAN had previously been offloaded with switchdev and had that
flag. Yet switchdev never notifies about that change, drivers are
supposed to guess).
Nonetheless, having a VLAN range in the API makes error handling look
scarier than it really is - unwinding on errors and all of that.
When in reality, no one really calls this API with more than one VLAN.
It is all unnecessary complexity.
And despite appearing pretentious (two-phase transactional model and
all), the switchdev API is really sloppy because the VLAN addition and
removal operations are not paired with one another (you can add a VLAN
100 times and delete it just once). The bridge notifies through
switchdev of a VLAN addition not only when the flags of an existing VLAN
change, but also when nothing changes. There are switchdev drivers out
there who don't like adding a VLAN that has already been added, and
those checks don't really belong at driver level. But the fact that the
API contains ranges is yet another factor that prevents this from being
addressed in the future.
Of the existing switchdev pieces of hardware, it appears that only
Mellanox Spectrum supports offloading more than one VLAN at a time,
through mlxsw_sp_port_vlan_set. I have kept that code internal to the
driver, because there is some more bookkeeping that makes use of it, but
I deleted it from the switchdev API. But since the switchdev support for
ranges has already been de facto deleted by a Mellanox employee and
nobody noticed for 4 years, I'm going to assume it's not a biggie.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com> # switchdev and mlxsw
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The qca8k only supports a switch-wide MTU setting, and the code to take
the max of all ports was only looking at the port currently being set.
Fix to examine all ports.
Reported-by: DENG Qingfang <dqfext@gmail.com>
Fixes: f58d2598cf70 ("net: dsa: qca8k: implement the port MTU callbacks")
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201030183315.GA6736@earth.li
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A driver may refuse to enable VLAN filtering for any reason beyond what
the DSA framework cares about, such as:
- having tc-flower rules that rely on the switch being VLAN-aware
- the particular switch does not support VLAN, even if the driver does
(the DSA framework just checks for the presence of the .port_vlan_add
and .port_vlan_del pointers)
- simply not supporting this configuration to be toggled at runtime
Currently, when a driver rejects a configuration it cannot support, it
does this from the commit phase, which triggers various warnings in
switchdev.
So propagate the prepare phase to drivers, to give them the ability to
refuse invalid configurations cleanly and avoid the warnings.
Since we need to modify all function prototypes and check for the
prepare phase from within the drivers, take that opportunity and move
the existing driver restrictions within the prepare phase where that is
possible and easy.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Landen Chao <Landen.Chao@mediatek.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Jonathan McDowell <noodles@earth.li>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds full 802.1q VLAN support to the qca8k, allowing the use of
vlan_filtering and more complicated bridging setups than allowed by
basic port VLAN support.
Tested with a number of untagged ports with separate VLANs and then a
trunk port with all the VLANs tagged on it.
v3:
- Pull QCA8K_PORT_VID_DEF changes into separate cleanup patch
- Reverse Christmas tree notation for variable definitions
- Use untagged instead of tagged for consistency
v2:
- Return sensible errnos on failure rather than -1 (rmk)
- Style cleanups based on Florian's feedback
- Silently allow VLAN 0 as device correctly treats this as no tag
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than using a magic value of 1 when configuring the port VIDs add
a QCA8K_PORT_VID_DEF define and use that instead. Also fix up the
bitmask in the process; the top 4 bits are reserved so this wasn't a
problem, but only masking 12 bits is the correct approach.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This switch has a single max frame size configuration register, so we
track the requested MTU for each port and apply the largest.
v2:
- Address review feedback from Vladimir Oltean
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Acked-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch improves the handling of the SGMII interface on the QCA8K
devices. Previously the driver did no configuration of the port, even if
it was selected. We now configure it up in the appropriate
PHY/MAC/Base-X mode depending on what phylink tells us we are connected
to and ensure it is enabled.
Tested with a device where the CPU connection is RGMII (i.e. the common
current use case) + one where the CPU connection is SGMII. I don't have
any devices where the SGMII interface is brought out to something other
than the CPU.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the driver to use the new PHYLINK callbacks, removing the
legacy adjust_link callback.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible to stack multiple DSA switches in a way that they are not
part of the tree (disjoint) but the DSA master of a switch is a DSA
slave of another. When that happens switch drivers may have to know this
is the case so as to determine whether their tagging protocol has a
remove chance of working.
This is useful for specific switch drivers such as b53 where devices
have been known to be stacked in the wild without the Broadcom tag
protocol supporting that feature. This allows b53 to continue supporting
those devices by forcing the disabling of Broadcom tags on the outermost
switches if necessary.
The get_tag_protocol() function is therefore updated to gain an
additional enum dsa_tag_protocol argument which denotes the current
tagging protocol used by the DSA master we are attached to, else
DSA_TAG_PROTO_NONE for the top of the dsa_switch_tree.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this change of_get_phy_mode() returned an enum,
phy_interface_t. On error, -ENODEV etc, is returned. If the result of
the function is stored in a variable of type phy_interface_t, and the
compiler has decided to represent this as an unsigned int, comparision
with -ENODEV etc, is a signed vs unsigned comparision.
Fix this problem by changing the API. Make the function return an
error, or 0 on success, and pass a pointer, of type phy_interface_t,
where the phy mode should be stored.
v2:
Return with *interface set to PHY_INTERFACE_MODE_NA on error.
Add error checks to all users of of_get_phy_mode()
Fixup a few reverse christmas tree errors
Fixup a few slightly malformed reverse christmas trees
v3:
Fix 0-day reported errors.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 0394a63acfe2 ("net: dsa: enable and disable all ports")
the dsa core disables all unused ports of a switch. In this case
disabling ports with numbers higher than QCA8K_NUM_PORTS causes that
some switch registers are overwritten with incorrect content.
To fix this, initialize the dsa_switch->num_ports with correct number
of ports.
Fixes: 7e99e3470172 ("net: dsa: remove dsa_switch_alloc helper")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that ports are dynamically listed in the fabric, there is no need
to provide a special helper to allocate the dsa_switch structure. This
will give more flexibility to drivers to embed this structure as they
wish in their private structure.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Do not let the drivers access the ds->ports static array directly
while there is a dsa_to_port helper for this purpose.
At the same time, un-const this helper since the SJA1105 driver
assigns the priv member of the returned dsa_port structure.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
The QCA8K family supports up to 7 ports. So use the existing
QCA8K_NUM_PORTS define to allocate the switch structure and limit all
operations with the switch ports.
This was not an issue until commit 0394a63acfe2 ("net: dsa: enable and
disable all ports") disabled all unused ports. Since the unused ports 7-11
are outside of the correct register range on this switch some registers
were rewritten with invalid content.
Fixes: 6b93fb46480a ("net-next: dsa: add new driver for qca8xxx family")
Fixes: a0c02161ecfc ("net: dsa: variable number of ports")
Fixes: 0394a63acfe2 ("net: dsa: enable and disable all ports")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPU port does not have a PHY connected to it. So calling
phy_support_asym_pause() results in an Opps. As with other DSA
drivers, add a guard that the port is a user port.
Reported-by: Michal Vokáč <michal.vokac@ysoft.com>
Fixes: 0394a63acfe2 ("net: dsa: enable and disable all ports")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each iteration of for_each_available_child_of_node() puts the previous
node, but in the case of a return from the middle of the loop, there
is no put, thus causing a memory leak. Hence add an of_node_put() before
the return.
Additionally, the local variable ports in the function
qca8k_setup_mdio_bus() takes the return value of of_get_child_by_name(),
which gets a node but does not put it. If the function returns without
putting ports, it may cause a memory leak. Hence put ports before the
mid-loop return statement, and also outside the loop after its last usage
in this function.
Issues found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set phy device advertising to enable MAC flow control.
Signed-off-by: Xiaofei Shen <xiaofeis@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces the legacy bulk gpio.h include
with the proper gpio/consumer.h variant. This was
caught by the kbuild test robot that was running
into an error because of this.
For more information why linux/gpio.h is bad can be found in:
commit 56a46b6144e7 ("gpio: Clarify that <linux/gpio.h> is legacy")
Reported-by: kbuild test robot <lkp@intel.com>
Link: https://www.spinics.net/lists/netdev/msg584447.html
Fixes: a653f2f538f9 ("net: dsa: qca8k: introduce reset via gpio feature")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The QCA8337(N) has a RESETn signal on Pin B42 that
triggers a chip reset if the line is pulled low.
The datasheet says that: "The active low duration
must be greater than 10 ms".
This can hopefully fix some of the issues related
to pin strapping in OpenWrt for the EA8500 which
suffers from detection issues after a SoC reset.
Please note that the qca8k_probe() function does
currently require to read the chip's revision
register for identification purposes.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements accessors for the QCA8337 MDIO access
through the MDIO_MASTER register, which makes it possible to
access the PHYs on slave-bus through the switch. In cases
where the switch ports are already mapped via external
"phy-phandles", the internal mdio-bus is disabled in order to
prevent a duplicated discovery and enumeration of the same
PHYs. Don't use mixed external and internal mdio-bus
configurations, as this is not supported by the hardware.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This belated patch implements Andrew Lunn's request of
"remove the phy_read() and phy_write() functions."
<https://lore.kernel.org/patchwork/comment/902734/>
While seemingly harmless, this causes the switch's user
port PHYs to get registered twice. This is because the
DSA subsystem will create a slave mdio-bus not knowing
that the qca8k_phy_(read|write) accessors operate on
the external mdio-bus. So the same "bus" gets effectively
duplicated.
Cc: stable@vger.kernel.org
Fixes: 6b93fb46480a ("net-next: dsa: add new driver for qca8xxx family")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No current DSA driver makes use of the phydev parameter passed to the
disable_port call. Remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
RGMII_ID specifies that we should have internal delay, so resurrect the
delay addition routine but under the RGMII_ID mode.
Fixes: 40269aa9f40a ("net: dsa: qca8k: disable delay for RGMII mode")
Tested-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In RGMII mode we should not have any delay in port MAC, so disable
the delay.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix warning reported by checkpatch.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the GPLv2 license boilerplate with the SPDX license identifier.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement adjust_link function that allows to overwrite default CPU port
setting using fixed-link device tree subnode.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default autonegotiation is enabled to configure MAC on all ports.
For the CPU port autonegotiation can not be used so we need to set
some sensible defaults manually.
This patch forces the default setting of the CPU port to 1000Mbps/full
duplex which is the chip maximum capability.
Also correct size of the bit field used to configure link speed.
Fixes: 6b93fb46480a ("net-next: dsa: add new driver for qca8xxx family")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port is brought up/down do not enable/disable only the TXMAC
but the RXMAC as well. This is essential for the CPU port to work.
Fixes: 6b93fb46480a ("net-next: dsa: add new driver for qca8xxx family")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the four-port variant of the Qualcomm QCA833x switch.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now we largely assumed that we were interested in ETH_SS_STATS
type of strings for all ethtool operations, this is about to change with
the introduction of additional string sets, e.g: ETH_SS_PHY_STATS.
Update all functions to take an appropriate stringset argument and act
on it when it is different than ETH_SS_STATS for now.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By passing the port, we allow different ports to have different
statistics. This is useful since some ports have SERDES interfaces
with their own statistic counters.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of drivers want to check whether the configured CPU port is a
possible configuration for enabling tagging, pass down the CPU port
number so they verify that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a dsa_user_ports() helper to return the ds->enabled_port_mask
mask which is more explicit. This will also minimize diffs when touching
this internal mask.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the DSA code still check ds->enabled_port_mask directly to
inspect a given port type instead of using the provided dsa_is_user_port
helper. Change this.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dsa_port structure is part of DSA core data and must only be updated
by the later. It is OK and sometimes necessary for the DSA drivers to
access this data, but this has to be read only.
For that purpose, add a dsa_to_port() helper which returns a const
pointer to a dsa_port structure which must be used by DSA drivers from
now on instead of digging into ds->ports[] themselves.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each port in DSA has its own dedicated CPU port currently available in
its parent switch's ds->ports[port].cpu_dp. Use it instead of getting
the unique tree CPU port, which will be deprecated soon.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make these const as they are not modified anywhere.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
>From all switchdev devices only DSA requires special FDB dump. This is due
to lack of ability for syncing the hardware learned FDBs with the bridge.
Due to this it is removed from switchdev and moved inside DSA.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The prepare phase for FDB add is unneeded because most of DSA devices
can have failures during bus transactions (SPI, I2C, etc.), thus, the
prepare phase cannot guarantee success of the commit stage.
The support for learning FDB through notification chain, which will be
introduced in the following patches, will provide the ability to notify
back the bridge about successful offload.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support FDB add/del to be on a notifier chain the slave
API need to be changed to be switchdev independent.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid confusion with the PHY EEE settings, rename the .set_eee and
.get_eee ops to respectively .set_mac_eee and .get_mac_eee.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
