Marvell phy 88E1145 configuration & initialization was missing a case
for initializing SGMII mode. This patch adds that case.
Signed-off-by: Vince Bridgers <vbridger@opensource.altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when slave 0 has no phy and slave 1 connected to phy, driver probe will
fail as there is no phy id present for slave 0 device tree, so continuing
even though no phy-id found, also moving mac-id read later to ensure
mac-id is read from device tree even when phy-id entry in not found.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless 2014-10-28
Please pull this batch of fixes intended for the 3.18 stream!
For the mac80211 bits, Johannes says:
"Here are a few fixes for the wireless stack: one fixes the
RTS rate, one for a debugfs file, one to return the correct
channel to userspace, a sanity check for a userspace value
and the remaining two are just documentation fixes."
For the iwlwifi bits, Emmanuel says:
"I revert here a patch that caused interoperability issues.
dvm gets a fix for a bug that was reported by many users.
Two minor fixes for BT Coex and platform power fix that helps
reducing latency when the PCIe link goes to low power states."
In addition...
Felix Fietkau adds a couple of ath code fixes related to regulatory
rule enforcement.
Hauke Mehrtens fixes a build break with bcma when CONFIG_OF_ADDRESS
is not set.
Karsten Wiese provides a trio of minor fixes for rtl8192cu.
Kees Cook prevents a potential information leak in rtlwifi.
Larry Finger also brings a trio of minor fixes for rtlwifi.
Rafał Miłecki adds a device ID to the bcma bus driver.
Rickard Strandqvist offers some strn* -> strl* changes in brcmfmac
to eliminate non-terminated string issues.
Sujith Manoharan avoids some ath9k stalls by enabling HW queue control
only for MCC.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6171 can support two different tagging protocols, DSA and
EDSA. The switch driver structure only allows one protocol to be
enumerated, and DSA was chosen. However the Kconfig entry ensures the
EDSA tagging code is built. With a minimal configuration, we then end
up with a mismatch. The probe is successful, EDSA tagging is used, but
the switch is configured for DSA, resulting in mangled packets.
Change the switch driver structure to enumerate EDSA, fixing the
mismatch.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 42f272539487 ("net: DSA: Marvell mv88e6171 switch driver")
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disabling DCBx in firmware automatically enables DCBx for control via host
lldp agents. Wait for an explicit setstate call from an lldp agents to enable
DCBx instead.
Fixes: 76bcb31efc06 ("cxgb4 : Add DCBx support codebase and dcbnl_ops")
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear out any DCB apps we might have added to kernel table when we lose DCB
sync (or IEEE equivalent event). These were previously left behind and not
cleaned up correctly. IEEE allows individual components to work independently,
so improve check for IEEE completion by specifying individual components.
Fixes: 10b0046685ab ("cxgb4: IEEE fixes for DCBx state machine")
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dvm gets a fix for a bug that was reported by many users.
Two minor fixes for BT Coex and platform power fix that helps
reducing latency when the PCIe link goes to low power states.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=iZLf
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-for-john-2014-10-23' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
Emmanuel Grumbach <egrumbach@gmail.com> says:
"I revert here a patch that caused interoperability issues.
dvm gets a fix for a bug that was reported by many users.
Two minor fixes for BT Coex and platform power fix that helps
reducing latency when the PCIe link goes to low power states."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After moving the EQ ownership to software effectively destroying it, call
synchronize_irq() to ensure that any handler routines running on other CPU
cores finish execution. Only then free the EQ buffer.
The same thing is done when we destroy a CQ which is one of the sources
generating interrupts. In the case of CQ we want to avoid completion handlers
on a CQ that was destroyed. In the case we do the same to avoid receiving
asynchronous events after the EQ has been destroyed and its buffers freed.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After destroying the EQ, the object responsible for generating interrupts, call
synchronize_irq() to ensure that any handler routines running on other CPU
cores finish execution. Only then free the EQ buffer. This patch solves a very
rare case when we get panic on driver unload.
The same thing is done when we destroy a CQ which is one of the sources
generating interrupts. In the case of CQ we want to avoid completion handlers
on a CQ that was destroyed. In the case we do the same to avoid receiving
asynchronous events after the EQ has been destroyed and its buffers freed.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/apm/xgene/xgene_enet_sgmac.c: In function ‘xgene_enet_ecc_init’:
drivers/net/ethernet/apm/xgene/xgene_enet_sgmac.c:126: warning: ‘data’ may be used uninitialized in this function
Depending on the arbitrary value on the stack, the loop may terminate
too early, and cause a bogus -ENODEV failure.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We accidentally mask by the _SHIFT variable. It means that "event" is
always zero.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to cancel the work queue after rcu grace period,
otherwise it can be rescheduled by incoming packets.
We need to purge queue if some skbs are still in it.
We can use __skb_queue_head_init() variant in
macvlan_process_broadcast()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 412ca1550cbec ("macvlan: Move broadcasts into a work queue")
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a frontend not receiving packets it is useful to detect this and
turn off the carrier so packets are dropped early instead of being
queued and drained when they expire.
A to-guest queue is stalled if it doesn't have enough free slots for a
an extended period of time (default 60 s).
If at least one queue is stalled, the carrier is turned off (in the
expectation that the other queues will soon stall as well). The
carrier is only turned on once all queues are ready.
When the frontend connects, all the queues start in the stalled state
and only become ready once the frontend queues enough Rx requests.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Netback needs to discard old to-guest skb's (guest Rx queue drain) and
it needs detect guest Rx stalls (to disable the carrier so packets are
discarded earlier), but the current implementation is very broken.
1. The check in hard_start_xmit of the slot availability did not
consider the number of packets that were already in the guest Rx
queue. This could allow the queue to grow without bound.
The guest stops consuming packets and the ring was allowed to fill
leaving S slot free. Netback queues a packet requiring more than S
slots (ensuring that the ring stays with S slots free). Netback
queue indefinately packets provided that then require S or fewer
slots.
2. The Rx stall detection is not triggered in this case since the
(host) Tx queue is not stopped.
3. If the Tx queue is stopped and a guest Rx interrupt occurs, netback
will consider this an Rx purge event which may result in it taking
the carrier down unnecessarily. It also considers a queue with
only 1 slot free as unstalled (even though the next packet might
not fit in this).
The internal guest Rx queue is limited by a byte length (to 512 Kib,
enough for half the ring). The (host) Tx queue is stopped and started
based on this limit. This sets an upper bound on the amount of memory
used by packets on the internal queue.
This allows the estimatation of the number of slots for an skb to be
removed (it wasn't a very good estimate anyway). Instead, the guest
Rx thread just waits for enough free slots for a maximum sized packet.
skbs queued on the internal queue have an 'expires' time (set to the
current time plus the drain timeout). The guest Rx thread will detect
when the skb at the head of the queue has expired and discard expired
skbs. This sets a clear upper bound on the length of time an skb can
be queued for. For a guest being destroyed the maximum time needed to
wait for all the packets it sent to be dropped is still the drain
timeout (10 s) since it will not be sending new packets.
Rx stall detection is reintroduced in a later commit.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Frontends that do not provide feature-rx-notify may stall because
netback depends on the notification from frontend to wake the guest Rx
thread (even if can_queue is false).
This could be fixed but feature-rx-notify was introduced in 2006 and I
am not aware of any frontends that do not implement this.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iwl_poll_bit may return a strictly positive value when the
poll doesn't match on the first try.
This was caught when WoWLAN started failing upon resume
even if the poll_bit actually succeeded.
Also change a wrong print. If we reach the end of
iwl_pcie_prepare_card_hw, it means that we couldn't
get the devices.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When mac80211 wants to ensure that a frame is sent, it calls
the flush() callback. Until now, iwldvm implemented this by
waiting that all the frames are sent (ACKed or timeout).
In case of weak signal, this can take a significant amount
of time, delaying the next connection (in case of roaming).
Many users have reported that the flush would take too long
leading to the following error messages to be printed:
iwlwifi 0000:03:00.0: fail to flush all tx fifo queues Q 2
iwlwifi 0000:03:00.0: Current SW read_ptr 161 write_ptr 201
iwl data: 00000000: 00 00 00 00 00 00 00 00 fe ff 01 00 00 00 00 00
[snip]
iwlwifi 0000:03:00.0: FH TRBs(0) = 0x00000000
[snip]
iwlwifi 0000:03:00.0: Q 0 is active and mapped to fifo 3 ra_tid 0x0000 [9,9]
[snip]
Instead of waiting for these packets, simply drop them. This
significantly improves the responsiveness of the network.
Note that all the queues are flushed, but the VO one. This
is not typically used by the applications and it likely
contains management frames that are useful for connection
or roaming.
This bug is tracked here:
https://bugzilla.kernel.org/show_bug.cgi?id=56581
But it is duplicated in distributions' trackers.
A simple search in Ubuntu's database led to these bugs:
https://bugs.launchpad.net/ubuntu/+source/linux-firmware/+bug/1270808https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1305406https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1356236https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1360597https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1361809
Cc: <stable@vger.kernel.org>
Depends-on: 77be2c54c5bd ("mac80211: add vif to flush call")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Don't add the time event to the list. We added it several
times the same time event, which leads to an infinite loop
when walking the list.
Since we (currently) don't support more than one ROC for STA
vif at a time, enforce this and don't add the time event
to any list.
We were also missing the locking of the mutex which led to
a lockdep splat - fix that.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The tx power should be limited from many reasons.
currently, setting the tx power is available by the mvm only for
station interface. Adding the tx power condition to
bss_info_changed_ap_ibss make it available also for AP.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
I changed the string but forgot to update the fix also to
MODULE_FIRMWARE().
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The LTR is the handshake between the device and the root
complex about the latency allowed when the bus exits power
save. This configuration was missing and this led to high
latency in the link power up. The end user could experience
high latency in the network because of this.
Cc: <stable@vger.kernel.org> [3.10+]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Drivers that do not use the get_btc_status() callback may not define a
dummy routine. The caller needs to check before making the call.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Murilo Opsfelder Araujo <mopsfelder@gmail.com>
Cc: Mike Galbraith <umgwanakikbuti@gmail.com>
Cc: Thadeu Cascardo <cascardo@cascardo.eti.br>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In some cases the limit may be the same as reg->power_limit, but the
actual value that the hardware uses is not up to date. In that case, a
wrong value for current tx power is tracked internally.
Fix this by unconditionally updating it.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rtl92c_set_fw_rsvdpagepkt is used by rtl8192cu and its pci sibling rtl8192ce.
rtl_cmd_send_packet crashes when called inside rtl8192cu because it works on
memory allocated only by rtl8192ce.
Fix the crash by calling a dummy function when used in rtl8192cu.
Comparision with the realtek vendor driver makes me think, something is missing in
the dummy function.
Short test as WPA2 station show good results connected to an 802.11g basestation.
Traffic stops after few MBytes as WPA2 station connected to an 802.11n basestation.
Signed-off-by: Karsten Wiese <fzuuzf@googlemail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In a previous patch the call to ieee80211_register_hw was moved from the
load firmware callback to the rtl_pci_probe only.
rt8192cu also uses this callback. Currently it doesnt create a wlan%d device.
Fill in the call to ieee80211_register_hw in rtl_usb_probe.
Signed-off-by: Karsten Wiese <fzuuzf@googlemail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Initialize function pointer with a function indicating bt coexist is not there.
Prevents Ooops.
Signed-off-by: Karsten Wiese <fzuuzf@googlemail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Many AP devices do not have the proper regulatory domain programmed in
EEPROM. Instead they expect the software to set the appropriate region.
For these devices, the country code defaults to US, and the driver uses
the US CTL tables as well.
On devices bought in Europe this can lead to tx power being set too high
on the band edges, even if the cfg80211 regdomain is set correctly.
Fix this issue by taking into account the DFS region, but only when the
EEPROM regdomain is set to default.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The kbuild test robot reported a possible array overrun. The affected code
checks for overruns, but fails to take the steps necessary to fix them.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enabling HW queue control for normal (non-mcc) mode
causes problems with queue management, resulting
in traffic stall. Since it is mainly required for
fairness in MCC mode, disable it for the general case.
Bug: https://dev.openwrt.org/ticket/18164
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use "%s" in the workqueue allocation to make sure the rtl_hal_cfg name
can never accidentally leak information via a format string.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replacing strncpy with strlcpy to avoid strings that lacks null terminate.
And changed from using strncat to strlcat to simplify code.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver logs a message when the default branch of switch statements are
taken. Such information is useful when debugging, but these log items should
not be seen for standard usage.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
total_data_buflen is used by netvsc_send() to decide if a packet can be put
into send buffer. It should also include the size of RNDIS message before the
Ethernet frame. Otherwise, a messge with total size bigger than send_section_size
may be copied into the send buffer, and cause data corruption.
[Request to include this patch to the Stable branches]
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the amd-xgbe driver increments the packets processed counter
each time a descriptor is processed. Since a packet can be represented
by more than one descriptor incrementing the counter in this way is not
appropriate. Also, since multiple descriptors cause the budget check
to be short circuited, sometimes the returned value from the poll
function would be larger than the budget value resulting in a WARN_ONCE
being triggered.
Update the polling logic to properly account for the number of packets
processed and exit when the budget value is reached.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ndo_set_features callback function was improperly using an unsigned
int to save the current feature value for features such as NETIF_F_RXCSUM.
Since that feature is in the upper 32 bits of a 64 bit variable the
result was always 0 making it not possible to actually turn off the
hardware RX checksum support. Change the unsigned int type to the
netdev_features_t type in order to properly capture the current value
and perform the proper operation.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 278d24047891 (net: fec: ptp: Enable PPS output based on ptp clock)
fec_enet_interrupt calls fec_ptp_check_pps_event unconditionally, which calls
into ptp_clock_event. If fep->ptp_clock is NULL, ptp_clock_event tries to
dereference the NULL pointer.
Since on i.MX53 fep->bufdesc_ex is not set, fec_ptp_init is never called,
and fep->ptp_clock is NULL, which reliably causes a kernel panic.
This patch adds a check for fep->ptp_clock == NULL in fec_enet_interrupt.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
After interface restart (eg: after link disconnection/reconnection), the bridge
function doesn't work anymore. This is due to the promiscuous mode being cleared
by the restart.
The mac-fcc already includes code to set the promiscuous mode back during the restart.
This patch adds the same handling to mac-fec and mac-scc.
Tested with bridge function on MPC885 with FEC.
Reported-by: Germain Montoies <germain.montoies@c-s.fr>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
write_count and insert_count can wrap around, making > check invalid.
Fixes: 70b33fb0ddec827cbbd14cdc664fc27b2ef4a6b6 ("sfc: add support for
skb->xmit_more").
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following warning is shown when spinlock debug is enabled.
This occurs when enic_flow_may_expire timer function is running and
enic_stop is called on same CPU.
Fix this by using spink_lock_bh().
=================================
[ INFO: inconsistent lock state ]
3.17.0-netnext-05504-g59f35b8 #268 Not tainted
---------------------------------
inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage.
ifconfig/443 [HC0[0]:SC0[0]:HE1:SE1] takes:
(&(&enic->rfs_h.lock)->rlock){+.?...}, at:
enic_rfs_flw_tbl_free+0x34/0xd0 [enic]
{IN-SOFTIRQ-W} state was registered at:
[<ffffffff810a25af>] __lock_acquire+0x83f/0x21c0
[<ffffffff810a45f2>] lock_acquire+0xa2/0xd0
[<ffffffff814913fc>] _raw_spin_lock+0x3c/0x80
[<ffffffffa029c3d5>] enic_flow_may_expire+0x25/0x130[enic]
[<ffffffff810bcd07>] call_timer_fn+0x77/0x100
[<ffffffff810bd8e3>] run_timer_softirq+0x1e3/0x270
[<ffffffff8105f9ae>] __do_softirq+0x14e/0x280
[<ffffffff8105fdae>] irq_exit+0x8e/0xb0
[<ffffffff8103da0f>] smp_apic_timer_interrupt+0x3f/0x50
[<ffffffff81493742>] apic_timer_interrupt+0x72/0x80
[<ffffffff81018143>] default_idle+0x13/0x20
[<ffffffff81018a6a>] arch_cpu_idle+0xa/0x10
[<ffffffff81097676>] cpu_startup_entry+0x2c6/0x330
[<ffffffff8103b7ad>] start_secondary+0x21d/0x290
irq event stamp: 2997
hardirqs last enabled at (2997): [<ffffffff81491865>] _raw_spin_unlock_irqrestore+0x65/0x90
hardirqs last disabled at (2996): [<ffffffff814915e6>] _raw_spin_lock_irqsave+0x26/0x90
softirqs last enabled at (2968): [<ffffffff813b57a3>] dev_deactivate_many+0x213/0x260
softirqs last disabled at (2966): [<ffffffff813b5783>] dev_deactivate_many+0x1f3/0x260
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(&enic->rfs_h.lock)->rlock);
<Interrupt>
lock(&(&enic->rfs_h.lock)->rlock);
*** DEADLOCK ***
Reported-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patch fixes a bug which causes the ax88179_178a driver to be
incapable of being added to a bond.
When I brought up the issue with the bonding maintainers, they indicated
that the real problem was with the NIC driver which must return zero for
success (of setting the MAC address). I see that several other NIC drivers
follow that pattern by either simply always returing zero, or by passing
through a negative (error) result while rewriting any positive return code
to zero. With that same philisophy applied to the ax88179_178a driver, it
allows it to work correctly with the bonding driver.
I believe this is suitable for queuing in -stable, as it's a small, simple,
and obvious fix that corrects a defect with no other known workaround.
This patch is against vanilla 3.17(.0).
Signed-off-by: Ian Morgan <imorgan@primordial.ca>
drivers/net/usb/ax88179_178a.c | 7 ++++++-
1 file changed, 6 insertions(+), 1 deletion(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull slave-dmaengine updates from Vinod Koul:
"For dmaengine contributions we have:
- designware cleanup by Andy
- my series moving device_control users to dmanegine_xxx APIs for
later removal of device_control API
- minor fixes spread over drivers mainly mv_xor, pl330, mmp, imx-sdma
etc"
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (60 commits)
serial: atmel: add missing dmaengine header
dmaengine: remove FSLDMA_EXTERNAL_START
dmaengine: freescale: remove FSLDMA_EXTERNAL_START control method
carma-fpga: move to fsl_dma_external_start()
carma-fpga: use dmaengine_xxx() API
dmaengine: freescale: add and export fsl_dma_external_start()
dmaengine: add dmaengine_prep_dma_sg() helper
video: mx3fb: use dmaengine_terminate_all() API
serial: sh-sci: use dmaengine_terminate_all() API
net: ks8842: use dmaengine_terminate_all() API
mtd: sh_flctl: use dmaengine_terminate_all() API
mtd: fsmc_nand: use dmaengine_terminate_all() API
V4L2: mx3_camer: use dmaengine_pause() API
dmaengine: coh901318: use dmaengine_terminate_all() API
pata_arasan_cf: use dmaengine_terminate_all() API
dmaengine: edma: check for echan->edesc => NULL in edma_dma_pause()
dmaengine: dw: export probe()/remove() and Co to users
dmaengine: dw: enable and disable controller when needed
dmaengine: dw: always export dw_dma_{en,dis}able
dmaengine: dw: introduce dw_dma_on() helper
...
been sitting in MST's tree during my vacation. I changed a function name
and made one trivial change, then they spent two days in linux-next.
Thanks,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=JK6x
-----END PGP SIGNATURE-----
Merge tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio updates from Rusty Russell:
"One cc: stable commit, the rest are a series of minor cleanups which
have been sitting in MST's tree during my vacation. I changed a
function name and made one trivial change, then they spent two days in
linux-next"
* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (25 commits)
virtio-rng: refactor probe error handling
virtio_scsi: drop scan callback
virtio_balloon: enable VQs early on restore
virtio_scsi: fix race on device removal
virito_scsi: use freezable WQ for events
virtio_net: enable VQs early on restore
virtio_console: enable VQs early on restore
virtio_scsi: enable VQs early on restore
virtio_blk: enable VQs early on restore
virtio_scsi: move kick event out from virtscsi_init
virtio_net: fix use after free on allocation failure
9p/trans_virtio: enable VQs early
virtio_console: enable VQs early
virtio_blk: enable VQs early
virtio_net: enable VQs early
virtio: add API to enable VQs early
virtio_net: minor cleanup
virtio-net: drop config_mutex
virtio_net: drop config_enable
virtio-blk: drop config_mutex
...
Pull networking fixes from David Miller:
1) Include fixes for netrom and dsa (Fabian Frederick and Florian
Fainelli)
2) Fix FIXED_PHY support in stmmac, from Giuseppe CAVALLARO.
3) Several SKB use after free fixes (vxlan, openvswitch, vxlan,
ip_tunnel, fou), from Li ROngQing.
4) fec driver PTP support fixes from Luwei Zhou and Nimrod Andy.
5) Use after free in virtio_net, from Michael S Tsirkin.
6) Fix flow mask handling for megaflows in openvswitch, from Pravin B
Shelar.
7) ISDN gigaset and capi bug fixes from Tilman Schmidt.
8) Fix route leak in ip_send_unicast_reply(), from Vasily Averin.
9) Fix two eBPF JIT bugs on x86, from Alexei Starovoitov.
10) TCP_SKB_CB() reorganization caused a few regressions, fixed by Cong
Wang and Eric Dumazet.
11) Don't overwrite end of SKB when parsing malformed sctp ASCONF
chunks, from Daniel Borkmann.
12) Don't call sock_kfree_s() with NULL pointers, this function also has
the side effect of adjusting the socket memory usage. From Cong Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (90 commits)
bna: fix skb->truesize underestimation
net: dsa: add includes for ethtool and phy_fixed definitions
openvswitch: Set flow-key members.
netrom: use linux/uaccess.h
dsa: Fix conversion from host device to mii bus
tipc: fix bug in bundled buffer reception
ipv6: introduce tcp_v6_iif()
sfc: add support for skb->xmit_more
r8152: return -EBUSY for runtime suspend
ipv4: fix a potential use after free in fou.c
ipv4: fix a potential use after free in ip_tunnel_core.c
hyperv: Add handling of IP header with option field in netvsc_set_hash()
openvswitch: Create right mask with disabled megaflows
vxlan: fix a free after use
openvswitch: fix a use after free
ipv4: dst_entry leak in ip_send_unicast_reply()
ipv4: clean up cookie_v4_check()
ipv4: share tcp_v4_save_options() with cookie_v4_check()
ipv4: call __ip_options_echo() in cookie_v4_check()
atm: simplify lanai.c by using module_pci_driver
...
skb->truesize is not meant to be tracking amount of used bytes
in an skb, but amount of reserved/consumed bytes in memory.
For instance, if we use a single byte in last page fragment,
we have to account the full size of the fragment.
skb->truesize can be very different from skb->len, that has
a very specific safety purpose.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b4d2394d01bc ("dsa: Replace mii_bus with a generic host device")
replaces mii_bus with a generic host_dev, and introduces
dsa_host_dev_to_mii_bus() to support conversion from host_dev to mii_bus.
However, in some cases it uses to_mii_bus to perform that conversion.
Since host_dev is not the phy bus device but typically a platform device,
this fails and results in a crash with the affected drivers.
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffff81781d35>] __mutex_lock_slowpath+0x75/0x100
PGD 406783067 PUD 406784067 PMD 0
Oops: 0002 [#1] SMP
...
Call Trace:
[<ffffffff810a538b>] ? pick_next_task_fair+0x61b/0x880
[<ffffffff81781de3>] mutex_lock+0x23/0x37
[<ffffffff81533244>] mdiobus_read+0x34/0x60
[<ffffffff8153b95a>] __mv88e6xxx_reg_read+0x8a/0xa0
[<ffffffff8153b9bc>] mv88e6xxx_reg_read+0x4c/0xa0
Fixes: b4d2394d01bc ("dsa: Replace mii_bus with a generic host device")
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't ring the doorbell, and don't do PIO. This will also prevent
TX Push, because there will be more than one buffer waiting when
the doorbell is rung.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
