When the adv748x driver is informed about a link being created from HDMI or
AFE to a CSI-2 TX output, the 'link_setup()' callback is invoked. Make
sure to implement proper routing management at link setup time, to route
the selected video stream to the desired TX output.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Both the AFE and HDMI s_stream routines (adv748x_afe_s_stream() and
adv748x_hdmi_s_stream()) have to enable the CSI-2 TX they are streaming video
data to.
With the introduction of dynamic routing between HDMI and AFE entities to
TXA, the video stream sink needs to be set at run time, and not statically
selected as the s_stream functions are currently doing.
To fix this, store a reference to the active CSI-2 TX sink for both HDMI and
AFE sources, and operate on it when starting/stopping the stream.
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The power_up_tx() procedure needs to set a few registers conditionally to
the selected video source, but it currently checks for the provided tx to
be either TXA or TXB.
With the introduction of dynamic routing between HDMI and AFE entities to
TXA, checking which TX the function is operating on is not meaningful anymore.
To fix this, store the subdevice of the source providing video data to the
CSI-2 TX in the 'struct adv748x_csi2' representing the TX and check on it.
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ADV748x chip supports routing AFE output to either TXA or TXB.
In order to support run-time configuration of video stream path, create an
additional (not enabled) "AFE:8->TXA:0" link, and remove the IMMUTABLE flag
from existing ones.
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add small is_txb() macro to the existing is_txa() and use it where
appropriate.
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Remove unused but set variables to clean up the code and avoid
warning.
Signed-off-by: Lucas A. M. Magalhães <lucmaga@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add VB2_USERPTR to the vimc capture device.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
A merge conflict rised when merging from -rc7. Fix it.
In this specific case, we don't need the if anymore, as the
work_run was moved to its rightful place (struct vim2m_ctx).
Fixes: b3e64e5b0778 ("media: vim2m: use per-file handler work queue")
Fixes: 240809ef6630 ("media: vim2m: only cancel work if it is for right context")
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The linked commit changed s_fmt/try_fmt to fail if num_planes is bogus.
This, however, is against the spec, which mandates drivers
to return a proper num_planes value, without an error.
Replace the num_planes check and instead clamp it to a sane value,
so we still make sure we don't overflow the planes array by accident.
Fixes: 9048b2e15b11c5 ("media: v4l: ioctl: Validate num_planes before using it")
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlxqHJYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGWl8H/jPI4EipzD2GbnjZ
GaFpMBBjcXBaVmoA+Y69so+7BHx1Ql+5GQtqbK0RHJRb9qEPLw3FBhHNjM/N8Sgf
nSrK+GnBZp9s+k/NR/Yf2RacUR3jhz+Q9JEoQd3u9bFUeQyvE8Rf3vgtoBBwFOfz
+t7N1memYVF3asLGWB4e4sP1YVMGfseTQpSPojvM30YWM86Bv+QtSx1AGgHczQIM
kMKealR8ZPelN6JAXgLhQ5opDojBrE4YKB98pwsMDI6abz0Tz2JLFEUTTxsv5XNN
o/Iz+XDoylskEyxN2unNWfHx7Swkvoklog8J/hDg5XlTvipL/WkT66PHBgcGMNvj
BW9GgU8=
=ZizU
-----END PGP SIGNATURE-----
Merge tag 'v5.0-rc7' into patchwork
Linux 5.0-rc7
* tag 'v5.0-rc7': (1667 commits)
Linux 5.0-rc7
Input: elan_i2c - add ACPI ID for touchpad in Lenovo V330-15ISK
Input: st-keyscan - fix potential zalloc NULL dereference
Input: apanel - switch to using brightness_set_blocking()
powerpc/64s: Fix possible corruption on big endian due to pgd/pud_present()
efi/arm: Revert "Defer persistent reservations until after paging_init()"
arm64, mm, efi: Account for GICv3 LPI tables in static memblock reserve table
sunrpc: fix 4 more call sites that were using stack memory with a scatterlist
include/linux/module.h: copy __init/__exit attrs to init/cleanup_module
Compiler Attributes: add support for __copy (gcc >= 9)
lib/crc32.c: mark crc32_le_base/__crc32c_le_base aliases as __pure
auxdisplay: ht16k33: fix potential user-after-free on module unload
x86/platform/UV: Use efi_runtime_lock to serialise BIOS calls
i2c: bcm2835: Clear current buffer pointers and counts after a transfer
i2c: cadence: Fix the hold bit setting
drm: Use array_size() when creating lease
dm thin: fix bug where bio that overwrites thin block ignores FUA
Revert "exec: load_script: don't blindly truncate shebang string"
Revert "gfs2: read journal in large chunks to locate the head"
net: ethernet: freescale: set FEC ethtool regs version
...
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It is good practice to fill in bus_info.
Also just use 'platform:vimc' when filling in the bus_info in querycap:
the bus_info has nothing to do with the video device name.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
drivers/media/platform/pxa_camera.c:2400 pxa_camera_probe() error: we previously assumed 'pcdev->pdata' could be null (see line 2397)
First check if platform data is provided, then check if DT data is provided,
and if neither is provided just return with -ENODEV.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
drivers/media/usb/hdpvr/hdpvr-i2c.c: drivers/media/usb/hdpvr/hdpvr-i2c.c:78 hdpvr_i2c_read() warn: 'dev->i2c_buf' 4216624615462223872 can't fit into 127 '*data'
dev->i2c_buf is a char array, so you can just use dev->i2c_buf to get the
start address, no need to do &dev->i2c_buf, even though it is the same
address in C. It only confuses smatch.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The v4l2_m2m_buf_copy_data helper is used to copy the buffer
metadata, such as its timestamp and its flags.
Therefore, the v4l2_m2m_buf_copy_metadata name is more clear
and avoids confusion with a payload data copy.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: also fix cedrus_dec.c]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It seems that it is possible that dev to be null, as there's
a warning printing:
"Instance released before the end of transaction"
Solves this warning:
drivers/media/platform/vim2m.c: drivers/media/platform/vim2m.c:525 device_work() warn: variable dereferenced before check 'curr_ctx' (see line 523)
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
To correctly set the size of the image in a plane, it's needed
to divide the height of image by the vertical down sampling factor.
This was only happening in vivid_try_fmt_vid_cap(), but now it
applied in others sizeimage calculations as well.
Signed-off-by: André Almeida <andre.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a linear pipeline logic for the stream control. It's created by
walking backwards on the entity graph. When the stream starts it will
simply loop through the pipeline calling the respective process_frame
function of each entity.
Fixes: f2fe89061d797 ("vimc: Virtual Media Controller core, capture
and sensor")
Cc: stable@vger.kernel.org # for v4.20
Signed-off-by: Lucas A. M. Magalhães <lucmaga@gmail.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: fixed small space-after-tab issue in the patch]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This function is no longer used, so drop it.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Just like vb2 does, use u64 internally to store the timestamps
of the buffers. Only convert to timeval when interfacing with
userspace.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Just like vb2 does, use u64 internally to store the timestamps
of the buffers. Only convert to timeval when interfacing with
userspace.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Just like vb2 does, use u64 internally to store the timestamps
of the buffers. Only convert to timeval when interfacing with
userspace.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Just like vb2 does, use u64 internally to store the timestamps
of the buffers. Only convert to timeval when interfacing with
userspace.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Just like vb2 does, use u64 internally to store the timestamps
of the buffers. Only convert to timeval when interfacing with
userspace.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Internally use ktime_get_ns() to get the timestamp of the event.
Only convert to timespec when interfacing with userspace.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The UVC video driver converts the timestamp from hardware specific unit
to one known by the kernel at the time when the buffer is dequeued. This
is fine in general, but the streamoff operation consists of the
following steps (among other things):
1. uvc_video_clock_cleanup --- the hardware clock sample array is
released and the pointer to the array is set to NULL,
2. buffers in active state are returned to the user and
3. buf_finish callback is called on buffers that are prepared.
buf_finish includes calling uvc_video_clock_update that accesses the
hardware clock sample array.
The above is serialised by a queue specific mutex. Address the problem
by skipping the clock conversion if the hardware clock sample array is
already released.
Fixes: 9c0863b1cc48 ("[media] vb2: call buf_finish from __queue_cancel")
Reported-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Tested-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When initially testing the Camera Terminal Descriptor wTerminalType
field (buffer[4]), no mask is used. Later in the function, the MSB is
overloaded to store the descriptor subtype, and so a mask of 0x7fff
is used to check the type.
If a descriptor is specially crafted to set this overloaded bit in the
original wTerminalType field, the initial type check will fail (falling
through, without adjusting the buffer size), but the later type checks
will pass, assuming the buffer has been made suitably large, causing an
overflow.
Avoid this problem by checking for the MSB in the wTerminalType field.
If the bit is set, assume the descriptor is bad, and abort parsing it.
Originally reported here:
https://groups.google.com/forum/#!topic/syzkaller/Ot1fOE6v1d8
A similar (non-compiling) patch was provided at that time.
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Alistair Strachan <astrachan@google.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The SOURCE_CHANGE event is decoder specific, so don't allow it for
encoders.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It is good practice to fill in the bus_info.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It is good practice to fill in bus_info.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Check that the selection buf_type is valid before calling get_q_data() to
avoid hitting the WARN(1) in that function if the buffer type is not valid.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: syzbot+44b24cff6bf96006ecfa@syzkaller.appspotmail.com
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Commit 2cc1802f62e5 ("media: vb2: Keep dma-buf buffers mapped until
they are freed") removed code leaving a local variable unused.
Remove it to avoid a compiler warning.
Fixes: 2cc1802f62e5 ("media: vb2: Keep dma-buf buffers mapped until they are freed")
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
While there's a control to allow setting it at runtime, as the
control handler is per file handler, only the application setting
the m2m device can change it. As this is a custom control, it is
unlikely that existing apps would be able to set it.
Due to that, and due to the fact that v4l2-mem2mem serializes all
accesses to a m2m device, trying to setup two GStreamer
v4l2videoconvert instance at the same time will cause frame drops.
So, add an alternate way of setting its default via a modprobe parameter.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It doesn't make sense to have a per-device work queue, as the
scheduler should be called per file handler. Having a single
one causes failures if multiple streams are filtered by vim2m.
So, move it to be inside the context structure.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Despite vim2m is reporting that it supports RGB565BE and YUYV,
that's not true.
Right now, it just says that it supports both format, but it
doesn't actually support them.
Also, horizontal flip is not properly implemented. It sounds
that it was designed to do a pseudo-horizontal flip using 8
tiles. Yet, as it doesn't do format conversion, the result
is a mess.
I suspect that it was done this way in order to save CPU time,
at the time of OMAP2 days.
That's messy and doesn't really help if someone wants to
use vim2m to test a pipeline.
Worse than that, the unique RGB format it says it supports is
RGB565BE, with is not supported by Gstreamer. That prevents
practical usage of it, even for tests.
So, instead, properly implement fourcc format conversions,
adding a few more RGB formats:
- RGB and BGR with 24 bits
- RGB565LE (known as RGB16 at gstreamer)
Also allows using any of the 5 supported formats as either
capture or output.
Note: The YUYV conversion routines are based on the conversion code
written by Hans de Goede inside libv4lconvert (part of v4l-utils),
released under LGPGL 2.1 (GPL 2.0 compatible).
Tested all possible format combinations except for RGB565BE,
as Gstreamer currently doesn't support it.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The wrong size check was performed for output formats like NV24 which
set vfmt->buffers to 1, but vfmt->planes is 2. It was incorrectly
checking the payload size for plane 1, which doesn't exist.
Note: vfmt->buffers refers to the number of per-plane-buffers that
should be allocated. vfmt->planes refers to the number of planes
that make up an image. vfmt->planes may be > vfmt->buffers.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The buf_out_validate is required for output queues in combination
with requests. Check this.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Validate the field for an output buffer. This ensures that the
field is validated when the buffer is queued to a request, and
not when the request itself is queued, which is too late.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Validate the field for an output buffer. This ensures that the
field is validated when the buffer is queued to a request, and
not when the request itself is queued, which is too late.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When queueing a buffer to a request the 'field' value is not validated.
That field is only validated when the _buf_prepare() is called,
which happens when the request is queued.
However, this validation should happen at QBUF time, since you want
to know about this as soon as possible. Also, the spec requires that
the 'field' value is validated at QBUF time.
This patch adds a new buf_out_validate callback to validate the
output buffer at buf_prepare time or when QBUF queues an unprepared
buffer to a request. This callback is mandatory for output queues
that support requests.
This issue was found by v4l2-compliance since it failed to replace
V4L2_FIELD_ANY by a proper field value when testing the vivid video
output in combination with requests.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When using vb2 for video decoding, dequeued capture buffers may still
be accessed by the hardware: this is the case when they are used as
reference frames for decoding subsequent frames.
When the buffer is imported with dma-buf, it needs to be mapped before
access. Until now, it was mapped when queuing and unmapped when
dequeuing, which doesn't work for access as a reference frames.
One way to solve this would be to map the buffer again when it is
needed as a reference, but the mapping/unmapping operations can
seriously impact performance. As a result, map the buffer once (when it
is first needed when queued) and keep it mapped until it is freed.
Reviewed-on: https://chromium-review.googlesource.com/334103
[Paul: Updated for mainline and changed commit message]
Signed-off-by: Pawel Osciak <posciak@chromium.org>
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There really is no reason why vb2_find_timestamp can't just find
buffers in any state. Drop that part of the test.
This also means that vb->timestamp should only be set to 0 when
the driver doesn't copy timestamps.
This change allows for more efficient pipelining (i.e. you can use
a buffer for a reference frame even when it is queued).
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Vdec: Using standard CCF interface to set parent clock and
clock rate in dtsi and using common interface to open/close
video decoder clock.
Venc: Using standard CCF interface to set parent clock in dtsi
and using common interface to open/close video encoder clock.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Signed-off-by: Qianqian Yan <qianqian.yan@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
drivers/media/platform/vicodec/vicodec-core.c:drivers/media/platform/vicodec/vicodec-core.c:210:23: warning: symbol 'get_next_header' was not declared. Should it be static?
drivers/media/platform/vicodec/vicodec-core.c:210:23: warning: no previous prototype for 'get_next_header' [-Wmissing-prototypes]
enum vb2_buffer_state get_next_header(struct vicodec_ctx *ctx, u8 **pp, u32 sz)
^~~~~~~~~~~~~~~
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Make sure that the pointer to the compressed frame does not
get out of the buffer.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If the the queues are not streaming then the first resolution
change is handled in the buf_queue callback.
The following resolution change events are handled in job_ready.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: wrap info_from_header prototype]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Keep the fwht header in separated field from the data.
Refactor job_ready to use a new function 'get_next_header'
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add flags indicating the pixel encoding - yuv/rgb/hsv to
fwht header and to the pixel info. Use it to enumerate
the supported pixel formats.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use 3 bits for the number of components mask in the fwht
header flags
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
