CP11x UTMI PHY supports swapping D+/D- signals via digital control
register 1.
Add support for the "swap-dx-lanes" device-tree property, which lists
the port-ids that should swap D+ and D-.
The property is evaluated in probe and applied before power-on
during mvebu_cp110_utmi_port_setup.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Link: https://lore.kernel.org/r/20241002-mvebu-utmi-phy-v4-1-83783dc89b9d@solid-run.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix the value of SIERRA_DEQ_OPENEYE_CTRL_PREG and add a definition for
SIERRA_DEQ_TAU_EPIOFFSET_MODE_PREG. This fixes the SGMII single link
register configuration.
Fixes: 7a5ad9b4b9 ("phy: cadence: Sierra: Update single link PCIe register configuration")
Signed-off-by: Bartosz Wawrzyniak <bwawrzyn@cisco.com>
Link: https://lore.kernel.org/r/20241003123405.1101157-1-bwawrzyn@cisco.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Return the actual error code upon failure to allocate extcon device, instead
of hardcoding -ENOMEM. Use dev_err_probe() to also log appropriate messages,
which is fine because the containing function is used in the probe path.
Helped-by: Heiko Stubner <heiko@sntech.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Dragan Simic <dsimic@manjaro.org>
Link: https://lore.kernel.org/r/cc4995aa3e569be6bc23ca126b41fba82d50eeee.1725524802.git.dsimic@manjaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Perform a few trivial code cleanups, e.g. to obey the reverse Christmas tree
rule, to avoid use of "{ ... }" code blocks where they aren't really needed,
or to avoid line wrapping by using the 100-column width better.
No intended functional changes are introduced by these code cleanups.
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Dragan Simic <dsimic@manjaro.org>
Link: https://lore.kernel.org/r/adce7309f6fd9e1191c53bab552a8531d1a71216.1725524802.git.dsimic@manjaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The Broadcom USB PHY driver contains a lookup table
(`reg_bits_map_tables`) to resolve register bitmaps unique to certain
versions of the USB PHY as found in various Broadcom chip families.
Historically, this table was just kept carefully in sync with the
"selector" enum every time the latter changed to ensure consistency.
However, a recent commit [1] introduced two new enumerators but did not
adjust the array for BCM4908, thus breaking the xHCI controller (and
boot process) on this platform and revealing the fragility of this
approach.
Since these arrays are a little sparse (many elements are zero) and the
position of the array elements is significant only insofar as they agree
with the enumerators, designated initializers are a better fit than
positional initializers here. Convert this table accordingly.
[1] 4536fe9640 ("phy: usb: suppress OC condition for 7439b2")
Signed-off-by: Sam Edwards <CFSworks@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Justin Chen <justin.chen@broadcom.com>
Link: https://lore.kernel.org/r/20241004034131.1363813-3-CFSworks@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The Broadcom USB PHY driver contains a lookup table
(`reg_bits_map_tables`) to resolve register bitmaps unique to certain
versions of the USB PHY as found in various Broadcom chip families. A
recent commit (see 'fixes' tag) introduced two new elements to each chip
family in this table -- except for one: BCM4908. This resulted in the
xHCI controller not being initialized correctly, causing a panic on
boot.
The next patch will update this table to use designated initializers in
order to prevent this from happening again. For now, just add back the
missing array elements to resolve the regression.
Fixes: 4536fe9640 ("phy: usb: suppress OC condition for 7439b2")
Signed-off-by: Sam Edwards <CFSworks@gmail.com>
Reviewed-by: Justin Chen <justin.chen@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20241004034131.1363813-2-CFSworks@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
- New Support
- Rcar usb2 support for RZ/G3S SoC
- Nuvoton MA35 SoC USB 2.0 PHY driver
- Removal
- obsolete qcom,usb-8x16-phy bindings
- Updates
- 4 lane PCIe support for Qualcomm X1E80100
- Constify structure in subsystem update
- Subsystem simplification with scoped for each OF child loop update
- Yaml conversion for Qualcomm sata phy, Hiilicon hi3798cv200-combphy
bindings
-----BEGIN PGP SIGNATURE-----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=XJmz
-----END PGP SIGNATURE-----
Merge tag 'phy-for-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy
Pull phy updates from Vinod Koul:
"New hw support:
- Rcar usb2 support for RZ/G3S SoC
- Nuvoton MA35 SoC USB 2.0 PHY driver
Removed:
- obsolete qcom,usb-8x16-phy bindings
Updates:
- 4 lane PCIe support for Qualcomm X1E80100
- Constify structure in subsystem update
- Subsystem simplification with scoped for each OF child loop update
- Yaml conversion for Qualcomm sata phy, Hiilicon hi3798cv200-combphy
bindings"
* tag 'phy-for-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (40 commits)
phy: renesas: rcar-gen3-usb2: Add support for the RZ/G3S SoC
dt-bindings: phy: renesas,usb2-phy: Document RZ/G3S phy bindings
phy: renesas: rcar-gen3-usb2: Add support to initialize the bus
phy: ti: j721e-wiz: Simplify with scoped for each OF child loop
phy: ti: j721e-wiz: Drop OF node reference earlier for simpler code
phy: ti: gmii-sel: Simplify with dev_err_probe()
phy: ti: am654-serdes: Use scoped device node handling to simplify error paths
phy: qcom: qmp-pcie-msm8996: Simplify with scoped for each OF child loop
phy: mediatek: xsphy: Simplify with scoped for each OF child loop
phy: mediatek: tphy: Simplify with scoped for each OF child loop
phy: hisilicon: usb2: Simplify with scoped for each OF child loop
phy: cadence: sierra: Simplify with scoped for each OF child loop
phy: broadcom: brcm-sata: Simplify with scoped for each OF child loop
phy: broadcom: bcm-cygnus-pcie: Simplify with scoped for each OF child loop
phy: nuvoton: add new driver for the Nuvoton MA35 SoC USB 2.0 PHY
dt-bindings: phy: nuvoton,ma35-usb2-phy: add new bindings
phy: qcom: qmp-pcie: Configure all tables on port B PHY
phy: airoha: adjust initialization delay in airoha_pcie_phy_init()
dt-bindings: phy: socionext,uniphier: add top-level constraints
phy: qcom: qmp-pcie: Add Gen4 4-lanes mode for X1E80100
...
* power-supply core
- introduce power_supply_show_enum_with_available() helper
- change usb_types from an array into a bitmask
- fix early usage of power_supply_property_is_writeable() resulting
in sysfs files not being writable
- fix missing temp1_max_alarm attribute in power-supply's hwmon devices
* drivers
- max1720x: expose nvmem device
- brcmstb: cleanup driver to use latest APIs
- max77693: expose input and charging current limit
- max17042_battery: fix state of charge reading for devices without
current sensing
- axp20x_battery: add AXP717 support
- axp20x_battery: fix min/max voltage properties
- axp20x_usb_power: add AXP717 support
- axp20x_usb_power: add DT based input current limit
* Documentation updates
* misc. minor cleanups and fixes
-----BEGIN PGP SIGNATURE-----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=UKRL
-----END PGP SIGNATURE-----
Merge tag 'for-v6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
"Power-supply core:
- introduce power_supply_show_enum_with_available() helper
- change usb_types from an array into a bitmask
- fix early usage of power_supply_property_is_writeable() resulting
in sysfs files not being writable
- fix missing temp1_max_alarm attribute in power-supply's hwmon
devices
Drivers:
- max1720x: expose nvmem device
- brcmstb: cleanup driver to use latest APIs
- max77693: expose input and charging current limit
- max17042_battery: fix state of charge reading for devices without
current sensing
- axp20x_battery: add AXP717 support
- axp20x_battery: fix min/max voltage properties
- axp20x_usb_power: add AXP717 support
- axp20x_usb_power: add DT based input current limit
Documentation updates
Misc minor cleanups and fixes"
* tag 'for-v6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (38 commits)
power: supply: hwmon: Fix missing temp1_max_alarm attribute
power: supply: Drop use_cnt check from power_supply_property_is_writeable()
power: supply: ab8500: Constify struct kobj_type
power: supply: max1720x: fix a double free on error in probe()
power: supply: axp20x_battery: add support for AXP717
power: supply: axp20x_usb_power: Add support for AXP717
dt-bindings: power: supply: axp20x: Add AXP717 compatible
dt-bindings: power: supply: axp20x: Add AXP717 compatible
power: supply: axp20x_usb_power: Fix spelling mistake "reqested" -> "requested"
power: supply: Change usb_types from an array into a bitmask
power: supply: sysfs: Move power_supply_show_enum_with_available() up
power: supply: sysfs: Add power_supply_show_enum_with_available() helper
power: supply: rt9467-charger: Remove "usb_type" property write support
power: supply: ucs1002: Adjust ucs1002_set_usb_type() to accept string values
power: supply: "usb_type" property may be written to
power: supply: max1720x: add read support for nvmem
mfd: axp20x: Add ADC, BAT, and USB cells for AXP717
power: supply: core: constify psy_tzd_ops
power: reset: brcmstb: Do not go into infinite loop if reset fails
power: reset: brcmstb: Use devm_register_sys_off_handler()
...
The bit_types array just hold a list of valid enum power_supply_usb_type
values which map to 0 - 9. This can easily be represented as a bitmap.
This reduces the size of struct power_supply_desc and further reduces
the data section size by drivers no longer needing to store the array.
This also unifies how usb_types are handled with charge_behaviours,
which allows power_supply_show_usb_type() to be removed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240831142039.28830-7-hdegoede@redhat.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add support for the Renesas RZ/G3S SoC. The support is similar with the
rest of RZ/G2 devices with the except that the RZ/G3S needs bus
initialization due to hardware limitation.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20240822152801.602318-13-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The Renesas RZ/G3S need to initialize the USB BUS before transferring data
due to hardware limitation. As the register that need to be touched for
this is in the address space of the USB PHY, and the UBS PHY need to be
initialized before any other USB drivers handling data transfer, add
support to initialize the USB BUS.
As the USB PHY is probed before any other USB drivers that enables
clocks and de-assert the reset signals and the BUS initialization is done
in the probe phase, we need to add code to de-assert reset signal and
runtime resume the device (which enables its clocks) before accessing
the registers.
As the reset signals are not required by the USB PHY driver for the other
USB PHY hardware variants, the reset signals and runtime PM was handled
only in the function that initialize the USB BUS.
The PHY initialization was done right after runtime PM enable to have
all in place when the PHYs are registered.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20240822152801.602318-11-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Drop OF node reference immediately after using it in
syscon_node_to_regmap(), which is both simpler and typical/expected
code pattern.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240826-phy-of-node-scope-v1-10-5b4d82582644@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Obtain the device node reference with scoped/cleanup.h to reduce error
handling and make the code a bit simpler.
Unlike in other typical of_node_get+syscon_node_to_regmap cases, the
reference cannot be dropped immediately after syscon_node_to_regmap(),
because further part of probe() uses it.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240826-phy-of-node-scope-v1-8-5b4d82582644@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use scoped for_each_available_child_of_node_scoped() when iterating over
device nodes to make code a bit simpler.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240826-phy-of-node-scope-v1-7-5b4d82582644@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use scoped for_each_available_child_of_node_scoped() when iterating over
device nodes to make code a bit simpler.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240826-phy-of-node-scope-v1-2-5b4d82582644@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use scoped for_each_available_child_of_node_scoped() when iterating over
device nodes to make code a bit simpler.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240826-phy-of-node-scope-v1-1-5b4d82582644@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Currently, only the RX and TX tables are written to the second PHY
(port B) when the 4-lanes mode is configured, but according to Qualcomm
internal documentation, the pcs, pcs_misc, serdes and ln_shrd tables need
to be written as well.
Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240805-phy-qcom-qmp-pcie-write-all-tbls-second-port-v3-1-6967c6bf61d1@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Align phy-pcie initialization delay to the vendor sdk in
airoha_pcie_phy_init routine and allow the hw to complete required
configuration before proceeding
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/8af6f27857619f1e0dd227f08b8584ae8fb22fb2.1722959625.git.lorenzo@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The sixth PCIe controller on X1E80100 can be used in either
4-lanes mode or 2-lanes mode. Add the configuration and compatible
for the 4-lane mode.
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240823-x1e80100-phy-add-gen4x4-v3-2-b7765631ca01@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
On a few Kria KR260 Robotics Starter Kit the PS-GEM SGMII linkup is not
happening after the resume. This is because serdes registers are reset
when FPD is off (in suspend state) and needs to be reprogrammed in the
resume path with the same default initialization as done in the first
stage bootloader psu_init routine.
To address the failure introduce a set of serdes registers to be saved in
the suspend path and then restore it on resume.
Fixes: 4a33bea003 ("phy: zynqmp: Add PHY driver for the Xilinx ZynqMP Gigabit Transceiver")
Signed-off-by: Piyush Mehta <piyush.mehta@amd.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/1722837547-2578381-1-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The HDMI PHY PLL can be used as an alternative dclk source to RK3588 SoC
CRU. It provides more accurate clock rates required by VOP2 to improve
existing support for display modes handling, which is known to be
problematic when dealing with non-integer refresh rates, among others.
It is worth noting this only works for HDMI 2.0 or below, e.g. cannot be
used to support HDMI 2.1 4K@120Hz mode.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20240620-rk3588-hdmiphy-clkprov-v2-4-6a2d2164e508@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When a new PHY is created via [devm_]phy_create(), the runtime PM for it
is not enabled unless the parent device (which creates the PHY) has its
own runtime PM already enabled.
Move the call to devm_pm_runtime_enable() before devm_phy_create() to
enable runtime PM at PHY core level.
With this change the ->power_on() and ->power_off() callbacks do not
require explicit runtime PM management anymore, since the PHY core
handles that via phy_pm_runtime_{get,put}_sync() when phy_power_on() and
phy_power_off() are invoked.
Hence drop the now unnecessary calls to pm_runtime_resume_and_get() and
pm_runtime_put() helpers.
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20240620-rk3588-hdmiphy-clkprov-v2-2-6a2d2164e508@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Driver makes use of helpers from pm_runtime.h, but relies on the header
file being implicitly included.
Explicitly pull the header in to avoid potential build failures in some
configurations.
Fixes: 553be2830c ("phy: rockchip: Add Samsung HDMI/eDP Combo PHY driver")
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20240620-rk3588-hdmiphy-clkprov-v2-1-6a2d2164e508@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The Torrent SERDES can support at most two different protocols (PHY types).
This only mandates that the device-tree sub-nodes used to represent the
configuration should describe links with at-most two different protocols.
The existing implementation however imposes an artificial constraint that
allows only two links (device-tree sub-nodes). As long as at-most two
protocols are chosen, using more than two links to describe them in an
alternating configuration is still a valid configuration of the Torrent
SERDES.
A 3-Link 2-Protocol configuration of the 4-Lane SERDES can be:
Lane 0 => Protocol 1 => Link 1
Lane 1 => Protocol 1 => Link 1
Lane 2 => Protocol 2 => Link 2
Lane 3 => Protocol 1 => Link 3
A 4-Link 2-Protocol configuration of the 4-Lane SERDES can be:
Lane 0 => Protocol 1 => Link 1
Lane 1 => Protocol 2 => Link 2
Lane 2 => Protocol 1 => Link 3
Lane 3 => Protocol 2 => Link 4
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240805092607.143869-1-s-vadapalli@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
According to the CN9100_MPP_information document, CP_SRD4 (comphy 4)
supports 2500 BASE-X and 5000 BASE-R for ETH_PORT1. I was able to test
that 2500 BASE-X is indeed supported. Unfortunately, our HW does not
support 5000 BASE-R, but I assume from the document that it does, so I
set the muxing there too to 0x1.
Signed-off-by: Stefan Eichenberger <eichest@gmail.com>
Link: https://lore.kernel.org/r/20240711131612.98952-1-eichest@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
According to fsl,imx8mq-usb-phy.yaml, this tuning parameter should be
fsl,phy-pcs-tx-deemph-3p5db-attenuation-db.
Fixes: 63c85ad0cd ("phy: fsl-imx8mp-usb: add support for phy tuning")
Cc: stable@vger.kernel.org
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20240801124642.1152838-1-xu.yang_2@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
These register prints are useful to validate the init sequence against the
Qcom internal documentation and also to share with the Qcom hw engineers to
debug issues related to PHY.
Sample debug prints:
qcom-qmp-pcie-phy 1c0e000.phy: Writing Reg: QSERDES_V5_COM_SYSCLK_EN_SEL Offset: 0x0094 Val: 0xd9
qcom-qmp-pcie-phy 1c0e000.phy: Writing Reg: QSERDES_V5_COM_HSCLK_SEL Offset: 0x0158 Val: 0x11
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240731152548.102987-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
'cdns_sierra_pll_mux_table' is not modified in this driver.
And it is only used as a "const u32 *".
Constifying this structure moves some data to a read-only section, so
increase overall security.
On a x86_64, with allmodconfig:
Before:
======
text data bss dec hex filename
60937 3894 16 64847 fd4f drivers/phy/cadence/phy-cadence-sierra.o
After:
=====
text data bss dec hex filename
60897 3878 16 64791 fd17 drivers/phy/cadence/phy-cadence-sierra.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/43d881d52e3c1632ad197d4c2c18b6c481a13b24.1720723132.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
'struct cdns_sierra_vals' is not modified in this driver.
Constifying this structure moves some data to a read-only section, so
increase overall security.
On a x86_64, with allmodconfig:
Before:
======
text data bss dec hex filename
60521 4310 16 64847 fd4f drivers/phy/cadence/phy-cadence-sierra.o
After:
=====
text data bss dec hex filename
60937 3894 16 64847 fd4f drivers/phy/cadence/phy-cadence-sierra.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/0ccfd259fdf40475c89cfb22a64c6388e7c646b4.1720723132.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
'struct cdns_reg_pairs' is not modified in this driver.
Constifying this structure moves some data to a read-only section, so
increase overall security.
On a x86_64, with allmodconfig:
Before:
======
text data bss dec hex filename
60489 4342 16 64847 fd4f drivers/phy/cadence/phy-cadence-sierra.o
After:
=====
text data bss dec hex filename
60521 4310 16 64847 fd4f drivers/phy/cadence/phy-cadence-sierra.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/c57ee8206ebba8c222d7d954335654384072b9ac.1720723132.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
'cdns_torrent_refclk_driver_mux_table' is not modified in this driver.
And it is only used as a "const u32 *".
Constifying this structure moves some data to a read-only section, so
increase overall security.
On a x86_64, with allmodconfig:
Before:
======
text data bss dec hex filename
93578 4798 16 98392 18058 drivers/phy/cadence/phy-cadence-torrent.o
After:
=====
text data bss dec hex filename
93606 4790 16 98412 1806c drivers/phy/cadence/phy-cadence-torrent.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/34e23ceb6b7b7eb730ee8deee21d231b504dc65f.1720718240.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
'struct cdns_torrent_vals' is not modified in this driver.
Constifying this structure moves some data to a read-only section, so
increase overall security.
On a x86_64, with allmodconfig:
Before:
======
text data bss dec hex filename
92234 6078 16 98328 18018 drivers/phy/cadence/phy-cadence-torrent.o
After:
=====
text data bss dec hex filename
93578 4798 16 98392 18058 drivers/phy/cadence/phy-cadence-torrent.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/d9d135ee9b806726766a1bc5e1404267939aa637.1720718240.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
'struct cdns_torrent_vals_entry' is not modified in this driver.
Constifying this structure moves some data to a read-only section, so
increase overall security.
On a x86_64, with allmodconfig:
Before:
======
text data bss dec hex filename
85130 13214 16 98360 18038 drivers/phy/cadence/phy-cadence-torrent.o
After:
=====
text data bss dec hex filename
92234 6078 16 98328 18018 drivers/phy/cadence/phy-cadence-torrent.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/dcc4e539999a840b3fd8f40fd8fd7523390232ac.1720718240.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
'struct cdns_reg_pairs' is not modified in this driver.
Constifying this structure moves some data to a read-only section, so
increase overall security.
On a x86_64, with allmodconfig:
Before:
======
text data bss dec hex filename
78154 20222 16 98392 18058 drivers/phy/cadence/phy-cadence-torrent.o
After:
=====
text data bss dec hex filename
85130 13214 16 98360 18038 drivers/phy/cadence/phy-cadence-torrent.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/803684a6f0c24d7e091dc8d285dd49c6fd31a010.1720718240.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use of FIELD_PREP_CONST() was a thinko - it's meant to be used for
(constant) initialisers, not constant values.
Use FIELD_PREP() where possible. It has better error checking and is
therefore the preferred macro to use in those cases.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20240710-phy-field-prep-v1-1-2fa3f7dc4fc7@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Here is the big set of USB and Thunderbolt changes for 6.11-rc1.
Nothing earth-shattering in here, just constant forward progress in
adding support for new hardware and better debugging functionalities for
thunderbolt devices and the subsystem. Included in here are:
- thunderbolt debugging update and driver additions
- xhci driver updates
- typec driver updates
- kselftest device driver changes (acked by the relevant maintainers,
depended on other changes in this tree.)
- cdns3 driver updates
- gadget driver updates
- MODULE_DESCRIPTION() additions
- dwc3 driver updates and fixes
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZppaNA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylXZwCgrEtIAQw0x6EF7w/iTWVS5UJj9AEAoLCj5UwO
WX978uThyUctuYYKbw+8
=Cm7j
-----END PGP SIGNATURE-----
Merge tag 'usb-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt changes for 6.11-rc1.
Nothing earth-shattering in here, just constant forward progress in
adding support for new hardware and better debugging functionalities
for thunderbolt devices and the subsystem. Included in here are:
- thunderbolt debugging update and driver additions
- xhci driver updates
- typec driver updates
- kselftest device driver changes (acked by the relevant maintainers,
depended on other changes in this tree.)
- cdns3 driver updates
- gadget driver updates
- MODULE_DESCRIPTION() additions
- dwc3 driver updates and fixes
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (112 commits)
kselftest: devices: Add test to detect device error logs
kselftest: Move ksft helper module to common directory
kselftest: devices: Move discoverable devices test to subdirectory
usb: gadget: f_uac2: fix non-newline-terminated function name
USB: uas: Implement the new shutdown callback
USB: core: add 'shutdown' callback to usb_driver
usb: typec: Drop explicit initialization of struct i2c_device_id::driver_data to 0
usb: dwc3: enable CCI support for AMD-xilinx DWC3 controller
usb: dwc2: add support for other Lantiq SoCs
usb: gadget: Use u16 types for 16-bit fields
usb: gadget: midi2: Fix incorrect default MIDI2 protocol setup
usb: dwc3: core: Check all ports when set phy suspend
usb: typec: tcpci: add support to set connector orientation
dt-bindings: usb: Convert fsl-usb to yaml
usb: typec: ucsi: reorder operations in ucsi_run_command()
usb: typec: ucsi: extract common code for command handling
usb: typec: ucsi: inline ucsi_read_message_in
usb: typec: ucsi: rework command execution functions
usb: typec: ucsi: split read operation
usb: typec: ucsi: simplify command sending API
...
Use regulator_hardware_enable() for controlling VBUS enable for
RZ/G2L alike SoCs in interrupt context.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20240702180032.207275-4-biju.das.jz@bp.renesas.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Introduce Tx-Rx detection Time and Rx AEQ training mappings to
phy-airoha-pcie driver. This is a preliminary patch to introduce PCIe
support to En7581 SoC through the mediatek-gen3 PCIe driver.
This change is not introducing any backward compatibility issue since
the EN7581 dts is not upstream yet.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/edf3b28926177166c65256604d69f2f576cb6fb3.1719682943.git.lorenzo@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for the Exynos USB 3.1 DRD combo phy, as found in Exynos 9
SoCs like Google GS101. It supports USB SS, HS and DisplayPort.
In terms of UTMI+, this is very similar to the existing Exynos850
support in this driver. The difference is that this combo phy supports
both UTMI+ (HS) and PIPE3 (SS). It also supports DP alt mode.
The number of ports for UTMI+ and PIPE3 can be determined using the
LINKPORT register (which also exists on Exynos E850).
For SuperSpeed (SS) a new SS phy is in use and its PIPE3 interface is
new compared to Exynos E850, and also very different from the existing
support for older Exynos SoCs in this driver.
The SS phy needs a bit more configuration work and register tuning for
signal quality to work reliably, presumably due to the higher
frequency, e.g. to account for different board layouts. Additionally,
power needs to be enabled before writing to the SS phy registers.
This commit adds the necessary changes for USB HS and SS to work.
DisplayPort is out of scope in this commit.
Notes:
* For the register tuning, exynos5_usbdrd_apply_phy_tunes() has been
added with the appropriate data structures to support tuning at
various stages during initialisation. Since these are hardware
specific, the platform data is supposed to be populated accordingly.
The implementation is loosely modelled after the Samsung UFS PHY
driver.
There is one tuning state for UTMI+, PTS_UTMI_POSTINIT, to execute
after init and generally intended for HS signal tuning, as done in
this commit.
PTS_PIPE3_PREINIT PTS_PIPE3_INIT PTS_PIPE3_POSTINIT
PTS_PIPE3_POSTLOCK are tuning states for PIPE3. In the downstream
driver, preinit differs by Exynos SoC, and postinit and postlock
are different per board. The latter haven't been implemented for
gs101 here, because downstream doesn't use them on gs101 either.
* Signal lock acquisition for SS depends on the orientation of the
USB-C plug. Since there currently is no infrastructure to chain
connector events to both the USB DWC3 driver and this phy driver, a
work-around has been added in
exynos5_usbdrd_usbdp_g2_v4_pma_check_cdr_lock() to check both
registers if it failed in one of the orientations.
* Equally, we can only establish SS speed in one of the connector
orientations due to programming differences when selecting the lane
mux in exynos5_usbdrd_usbdp_g2_v4_pma_lane_mux_sel(), which really
needs to be dynamic, based on the orientation of the connector.
* As is, we can establish a HS link using any cable, and an SS link in
one orientation of the plug, falling back to HS if the orientation is
reversed to the expectation.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Link: https://lore.kernel.org/r/20240617-usb-phy-gs101-v3-6-b66de9ae7424@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Using the regulator_bulk APIs, the handling of power supplies becomes
much simpler. There is no need anymore to check if regulators have been
acquired or not, the bulk APIs will do all the work for us. We can also
drop the various handles to the individual power supplies in the driver
runtime data and instead simply treat them all as one thing. Error
cleanup also becomes much simpler.
Converting to the regulator_bulk APIs also makes it easier to add
support for those SoCs that have additional power supplies for the PHY.
Google Tensor gs101 is one example of such a SoC. Otherwise we'd have
to add all additional supplies individually via individual calls to
regulator_get() and enable/disable handle them all individually,
including complicated error handling. That doesn't scale and clutters
the code.
Just update the code to use the regulator_bulk APIs.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240617-usb-phy-gs101-v3-5-b66de9ae7424@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation for support for additional platforms, convert the phy
register access clock to using the clk_bulk interfaces.
Newer SoCs like Google Tensor gs101 require additional clocks for
access to additional (different) register areas (PHY, PMA, PCS), and
converting to clk_bulk simplifies addition of those extra clocks.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Link: https://lore.kernel.org/r/20240617-usb-phy-gs101-v3-4-b66de9ae7424@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Using the clk_bulk APIs, the clock handling for the core clocks becomes
much simpler. No need to check any flags whether or not certain clocks
exist or not. Further, we can drop the various handles to the
individual clocks in the driver data and instead simply treat them all
as one thing.
So far, this driver assumes that all platforms have a clock "ref". It
also assumes that the clocks "phy_pipe", "phy_utmi", and "itp" exist if
the platform data "has_common_clk_gate" is set to true. It then goes
and individually tries to acquire and enable and disable all the
individual clocks one by one. Rather than relying on these implicit
clocks and open-coding the clock handling, we can just explicitly spell
out the clock names in the different device data and use that
information to populate clk_bulk_data, allowing us to use the clk_bulk
APIs for managing the clocks.
As a side-effect, this change highlighted the fact that
exynos5_usbdrd_phy_power_on() forgot to check the result of the clock
enable calls. Using the clk_bulk APIs, the compiler now warns when
return values are not checked - therefore add the necessary check
instead of silently ignoring failures and continuing as if all is OK
when it isn't.
For consistency, also change a related dev_err() to dev_err_probe() in
exynos5_usbdrd_phy_clk_handle() to get consistent error message
formatting.
Finally, exynos5_usbdrd_phy_clk_handle() prints an error message in all
cases as necessary (except for -ENOMEM). There is no need to print
another message in its caller (the probe() function), and printing
errors during OOM conditions is usually discouraged. Drop the
duplicated message in exynos5_usbdrd_phy_probe().
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240617-usb-phy-gs101-v3-3-b66de9ae7424@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Some versions of this IP have been integrated using separate PMU power
control registers for the HS and SS parts. One example is the Google
Tensor gs101 SoC.
Such SoCs can now set pmu_offset_usbdrd0_phy_ss in their
exynos5_usbdrd_phy_drvdata for the SS phy to the appropriate value.
The existing 'usbdrdphy' alias can not be used in this case because
that is meant for determining the correct PMU offset if multiple
distinct PHYs exist in the system (as opposed to one PHY with multiple
isolators).
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240617-usb-phy-gs101-v3-2-b66de9ae7424@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We actually want to calculate the alignment values first, then
use the alignment value to look up the data from reg_configs[].
Fixes: d3ab795533 ("phy: starfive: Add mipi dphy tx support")
Reviewed-by: Shengyang Chen <shengyang.chen@starfivetech.com>
Signed-off-by: Changhuang Liang <changhuang.liang@starfivetech.com>
Link: https://lore.kernel.org/r/20240627020059.163535-1-changhuang.liang@starfivetech.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for printing some basic status information to debugfs. This
is helpful when debugging phy consumers to make sure they are configuring
the phy appropriately.
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Link: https://lore.kernel.org/r/20240628205540.3098010-6-sean.anderson@linux.dev
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Take the phy mutex in xlate to protect against concurrent
modification/access to gtr_phy. This does not typically cause any
issues, since in most systems the phys are only xlated once and
thereafter accessed with the phy API (which takes the locks). However,
we are about to allow userspace to access phys for debugging, so it's
important to avoid any data races.
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Link: https://lore.kernel.org/r/20240628205540.3098010-5-sean.anderson@linux.dev
Signed-off-by: Vinod Koul <vkoul@kernel.org>
For PCIe and DisplayPort, the phy instance represents the controller's
logical lane. Wait for the instance 0 phy's PLL to lock as other
instances will never lock. We do this in xpsgtr_wait_pll_lock so callers
don't have to determine the correct lane themselves.
The original comment is wrong about cumulative wait times. Since we are
just polling a bit, all subsequent waiters will finish immediately.
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Link: https://lore.kernel.org/r/20240628205540.3098010-4-sean.anderson@linux.dev
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The phy "type" is just the combination of protocol and instance, and is
never used apart from that. Store the instance directly, instead of
converting to a type first. No functional change intended.
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Link: https://lore.kernel.org/r/20240628205540.3098010-3-sean.anderson@linux.dev
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Lanes can use other lanes' reference clocks, as determined by refclk.
Use refclk to determine the clock to enable/disable instead of always
using the lane's own reference clock. This ensures the clock selected in
xpsgtr_configure_pll is the one enabled.
For the other half of the equation, always program REF_CLK_SEL even when
we are selecting the lane's own clock. This ensures that Linux's idea of
the reference clock matches the hardware. We use the "local" clock mux
for this instead of going through the ref clock network.
Fixes: 25d7008335 ("phy: xilinx: phy-zynqmp: dynamic clock support for power-save")
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Link: https://lore.kernel.org/r/20240628205540.3098010-2-sean.anderson@linux.dev
Signed-off-by: Vinod Koul <vkoul@kernel.org>
cdns_torrent_dp_set_power_state() does not consider that ret might be
overwritten. Add return value check of regmap_read_poll_timeout() after
register read in cdns_torrent_dp_set_power_state().
Fixes: 5b16a790f1 ("phy: cadence-torrent: Reorder few functions to remove function declarations")
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240702032042.3993031-1-make24@iscas.ac.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Compile testing configurations without REGMAP support enabled results in
a bunch of errors being reported:
../drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c:569:21: error: variable ‘rk_hdptx_phy_regmap_config’ has initializer but incomplete type
569 | static const struct regmap_config rk_hdptx_phy_regmap_config = {
| ^~~~~~~~~~~~~
../drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c:570:10: error: ‘const struct regmap_config’ has no member named ‘reg_bits’
570 | .reg_bits = 32,
| ^~~~~~~~
Note that selecting REGMAP alone is not enough, because of the following
liker error:
phy-rockchip-samsung-hdptx.c:(.text+0x10c): undefined reference to `__devm_regmap_init_mmio_clk'
Instead of the obvious fix to enable REGMAP_MMIO, select MFD_SYSCON,
which implicitly enables REGMAP_MMIO as well. The rationale is that the
driver has been already relying on the syscon functionality.
Moreover, without MFD_SYSCON enabled, the test coverage is reduced,
since the linker might not detect any potential undefined references
following syscon_regmap_lookup_by_phandle() invocation in
rk_hdptx_phy_probe() body. That is because the function would
unconditionally return -ENOTSUP, hence the compiler is free to optimize
out any unreachable code.
Finally ensure PHY_ROCKCHIP_SAMSUNG_HDPTX depends on HAS_IOMEM, as
required by MFD_SYSCON.
Fixes: 553be2830c ("phy: rockchip: Add Samsung HDMI/eDP Combo PHY driver")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20240629-rk-hdptx-compile-test-fix-v1-1-c86675ba8070@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Introduce support for Airoha PCIe PHY controller available in EN7581
SoC.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Zhengping Zhang <zhengping.zhang@airoha.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/20ac99aa8628d97778594f606681db7f868f24fe.1718485860.git.lorenzo@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In various configurations/architectures, bitfield.h may not be
transitively included, which results in a compiler error because
FIELD_PREP is an unexpanded macro:
drivers/phy/freescale/phy-fsl-imx8qm-hsio.c:459:8: error: call to undeclared function 'FIELD_PREP'; ISO C99 and later do not support implicit function declarations [-Wimplicit-function-declaration]
459 | val = FIELD_PREP(HSIO_MODE_MASK, val);
| ^
1 error generated.
Include bitfield.h explicitly to fix the build.
Fixes: 82c56b6dd2 ("phy: freescale: imx8qm-hsio: Add i.MX8QM HSIO PHY driver support")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202406170340.7mk3WU3Q-lkp@intel.com/
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240620-phy-fsl-imx8qm-hsio-add-bitfield-include-v1-1-5c7c09ed87e6@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add i.MX8QM HSIO PHY driver support.
i.MX8QM HSIO has three lane PHY instances, and can be bound to the
following controllers in the different use cases listed in below table.
- two lanes capable PCIEA controller.
- one lane PCIEB controller.
- AHCI SATA controller.
i.MX8QM HSIO PHYs support the following use cases.
+----------------------------------------------------+
| | Lane0| Lane1| Lane2|
|-------------------------------|------|------|------|
| use case 1: PCIEAX2SATA | PCIEA| PCIEA| SATA |
|-------------------------------|------|------|------|
| use case 2: PCIEAX2PCIEB | PCIEA| PCIEA| PCIEB|
|-------------------------------|------|------|------|
| use case 3: PCIEAPCIEBSATA | PCIEA| PCIEB| SATA |
+----------------------------------------------------+
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/1716962565-2084-3-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add mipi dphy tx support for the StarFive JH7110 SoC.
It is a module which is used to receive data from DSI
driver and transfer data to DSI interface like mipi screen.
Signed-off-by: Shengyang Chen <shengyang.chen@starfivetech.com>
Reviewed-by: Changhuang Liang <changhuang.liang@starfivetech.com>
Link: https://lore.kernel.org/r/20240418035020.47876-3-shengyang.chen@starfivetech.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Existing device trees specify only a single clock-output-name for the
PCIe PHYs. The function phy_aux_clk_register() expects a second entry in
that property. When it doesn't find it, it returns an error, thus
failing the probe of the PHY and thus breaking support for the
corresponding PCIe host.
Follow the approach of the combo USB+DT PHY and generate the name for
the AUX clocks instead of requiring it in DT.
Fixes: 583ca9ccfa ("phy: qcom: qmp-pcie: register second optional PHY AUX clock")
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240614-fix-pcie-phy-compat-v3-1-730d1811acf4@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/phy/broadcom/phy-bcm-ns-usb2.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/phy/broadcom/phy-bcm-ns-usb3.o
Add the missing invocations of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://lore.kernel.org/r/20240608-md-drivers-phy-broadcom-v1-1-f070f84cc3f0@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
While commit 255ec3879d ("phy: exynos5-usbdrd: Add 26MHz ref clk
support") correctly states that CLKRSTCTRL[7:5] doesn't need to be set
on modern Exynos platforms, SSPPLLCTL[2:0] should be programmed with
the frequency of the reference clock for the USB2.0 phy instead.
I stumbled across this while adding support for the Google Tensor
gs101, but this should apply to E850 just the same.
Do so.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240507-samsung-usb-phy-fixes-v1-5-4ccba5afa7cc@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Using 0x82 seems odd, where everything else is just a sequence.
On E850, this macro isn't used (as a register value), only to assign
its value to the 'extrefclk' variable, which is otherwise unused on
that platform. Older platforms don't appear to support 26MHz in the
first place (since this macro was added for E850).
Furthermore, the downstream driver uses 0x82 to denote
USBPHY_REFCLK_DIFF_26MHZ (whatever that means exactly), but for all the
other values we match downstream's non-DIFF macros.
Update to avoid confusion. No functional change intended.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240507-samsung-usb-phy-fixes-v1-4-4ccba5afa7cc@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
on / not on is just a boolean flag and is a bit misleading as currently
on==1 means to turn off the power, and on==0 to turn power on.
Rename the flag and make it a bool to avoid confusion of future readers
of this code. No functional change.
While at it, fix a whitespace issue in nearby comment.
No functional change.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240507-samsung-usb-phy-fixes-v1-3-4ccba5afa7cc@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The timers-howto recommends using usleep_range() and friends anytime
waiting for >= ~10us is required. Doing so can help the timer subsystem
a lot to coalesce wakeups.
Additionally, fsleep() exists as a convenient wrapper so we do not have
to think about which exact sleeping function is required in which case.
Convert all udelay() calls in this driver to use fsleep() to follow the
recommendataion.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240507-samsung-usb-phy-fixes-v1-2-4ccba5afa7cc@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Most of the macros are ordered high -> low, but there are some
outliers.
Order them all uniformly from high to low. This will allow adding
additional register (field) definitions in a consistent way.
While at it, also remove some extra empty lines to group register bit
field definitions together with the relevant register. This makes the
registers easier to distinguish visually.
No functional change.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240507-samsung-usb-phy-fixes-v1-1-4ccba5afa7cc@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Runtime PM is not supported while USB PHY can be turned off from
register accesses.
Add runtime PM for the USB2.0 PHY. The PHY is entirely shut down to save
as much power as possible. This means that gadgets will not be discovered
once suspend state is entered, and suspend state can not be left without
an explicit user intervention (through sysfs). That's why runtime PM is
disabled by default.
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Link: https://lore.kernel.org/r/20240528102026.40136-2-bastien.curutchet@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for a single-lane and two-lane PCIe PHYs
found on Qualcomm IPQ9574 platform.
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Co-developed-by: Anusha Rao <quic_anusha@quicinc.com>
Signed-off-by: Anusha Rao <quic_anusha@quicinc.com>
Signed-off-by: devi priya <quic_devipriy@quicinc.com>
Link: https://lore.kernel.org/r/20240516032436.2681828-5-quic_devipriy@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Currently, none of the X1E80100 supported boards upstream have enabled
DP. As for USB, the reason it is not broken when it's obvious that the
offsets are wrong is because the only difference with respect to USB is
the difference in register name. The V6 uses QPHY_V6_PCS_CDR_RESET_TIME
while V6 N4 uses QPHY_V6_N4_PCS_RX_CONFIG. Now, in order for the DP to
work, the DP serdes tables need to be added as they have different
values for V6 N4 when compared to V6 ones, even though they use the same
V6 offsets. While at it, switch swing and pre-emphasis tables to V6 as
well.
Fixes: d7b3579f84 ("phy: qcom-qmp-combo: Add x1e80100 USB/DP combo phys")
Co-developed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240527-x1e80100-phy-qualcomm-combo-fix-dp-v1-3-be8a0b882117@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The new X1E80100 SoC bumps up the HW version of QMP phy to v6 N4 for
combo USB and DP PHY. Currently, the X1E80100 uses the pure V6 PCS
register offsets, which are different. Add the offsets so the
mentioned platform can be fixed later on. Add the new PCS offsets
in a dedicated header file.
Fixes: d7b3579f84 ("phy: qcom-qmp-combo: Add x1e80100 USB/DP combo phys")
Co-developed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240527-x1e80100-phy-qualcomm-combo-fix-dp-v1-2-be8a0b882117@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Currently, the x1e80100 uses pure V6 register offsets for DP part of the
combo PHY. This hasn't been an issue because external DP is not yet
enabled on any of the boards yet. But in order to enabled it, all these
new V6 N4 register offsets are needed. So add them.
Fixes: 762c3565f3 ("phy: qcom-qmp: qserdes-txrx: Add V6 N4 register offsets")
Co-developed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240527-x1e80100-phy-qualcomm-combo-fix-dp-v1-1-be8a0b882117@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
'miphy_initval' is unused since the original
commit 2c14e9be0c ("phy: miphy28lp: Provide support for the MiPHY28lp
Generic PHY").
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://lore.kernel.org/r/20240527205844.165279-1-linux@treblig.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
'regval' is unused since the original
commit f8aa660841 ("phy: starfive: Add mipi dphy rx support").
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Reviewed-by: Changhuang Liang <changhuang.liang@starfivetech.com>
Link: https://lore.kernel.org/r/20240527205937.165325-1-linux@treblig.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The SC8180X platform has two UNIPHY blocks, add support for these in the
QMP driver.
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240525-sc8180x-usb-mp-v1-2-60a904392438@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add suspend and resume support.
The already_configured flag is cleared during the suspend stage to force
the PHY initialization during the resume stage.
Co-developed-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://lore.kernel.org/r/20240412-j7200-phy-s2r-v1-8-f15815833974@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Even if a PHY is already configured, the PHY operations are needed during
resume stage, as the PHY is in reset state.
The noop_ops PHY operations is removed to always have PHY operations.
The already_configured flag is checked at the begening of init, configure
and poweron operations to keep the already_configured behaviour.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://lore.kernel.org/r/20240412-j7200-phy-s2r-v1-7-f15815833974@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Resets are needed during suspend and resume stages.
So they shall be registered during the probe even the phy is already
initialized.
The function cdns_torrent_reset is renamed cdns_torrent_of_get_reset() to
make it clear.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://lore.kernel.org/r/20240412-j7200-phy-s2r-v1-5-f15815833974@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Extract calls to clk_get from cdns_torrent_clk into a separate function.
It needs to call cdns_torrent_clk at resume without looking up the clock.
Co-developed-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://lore.kernel.org/r/20240412-j7200-phy-s2r-v1-4-f15815833974@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add resume support.
It has been tested on J7200 SR1.0 and SR2.0.
Co-developed-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://lore.kernel.org/r/20240412-j7200-phy-s2r-v1-3-f15815833974@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The wiz_clock_init() function mixes probe and hardware configuration.
Rename the wiz_clock_init() to wiz_clock_probe() and move the hardware
configuration part in a new function named wiz_clock_init().
This hardware configuration sequence must be called during the resume
stage of the driver.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://lore.kernel.org/r/20240412-j7200-phy-s2r-v1-2-f15815833974@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
- New Support
- Support for Embedded DisplayPort and DisplayPort submodes and driver
support on Qualcomm X1E80100 edp driver
- Qualcomm QMP UFS PHY for SM8475, QMP USB phy for QDU1000/QRU1000 and
eusb2-repeater for SMB2360
- Samsung HDMI PHY for i.MX8MP, gs101 UFS phy
- Mediatek XFI T-PHY support for mt7988
- Rockchip usbdp combo phy driver
- Updates
- Qualcomm x4 lane EP support for sa8775p, v4 ad v6 support for X1E80100,
SM8650 tables for UFS Gear 4 & 5 and correct voltage swing tables
- Freescale imx8m-pci pcie link-up updates
- Rockchip rx-common-refclk-mode support
- More platform remove callback returning void conversions
-----BEGIN PGP SIGNATURE-----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=og1j
-----END PGP SIGNATURE-----
Merge tag 'phy-for-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy
Pull generic phy updates from Vinod Koul:
"New HW Support:
- Support for Embedded DisplayPort and DisplayPort submodes and
driver support on Qualcomm X1E80100 edp driver
- Qualcomm QMP UFS PHY for SM8475, QMP USB phy for QDU1000/QRU1000
and eusb2-repeater for SMB2360
- Samsung HDMI PHY for i.MX8MP, gs101 UFS phy
- Mediatek XFI T-PHY support for mt7988
- Rockchip usbdp combo phy driver
Updates:
- Qualcomm x4 lane EP support for sa8775p, v4 ad v6 support for
X1E80100, SM8650 tables for UFS Gear 4 & 5 and correct voltage
swing tables
- Freescale imx8m-pci pcie link-up updates
- Rockchip rx-common-refclk-mode support
- More platform remove callback returning void conversions"
* tag 'phy-for-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (43 commits)
dt-bindings: phy: qcom,usb-snps-femto-v2: use correct fallback for sc8180x
dt-bindings: phy: qcom,sc8280xp-qmp-ufs-phy: fix msm899[68] power-domains
dt-bindings: phy: qcom,sc8280xp-qmp-pcie-phy: fix x1e80100-gen3x2 schema
phy: qcpm-qmp-usb: Add support for QDU1000/QRU1000
dt-bindings: phy: qcom,qmp-usb: Add QDU1000 USB3 PHY
dt-bindings: phy: qcom,usb-snps-femto-v2: Add bindings for QDU1000
phy: qcom-qmp-pcie: add x4 lane EP support for sa8775p
phy: samsung-ufs: ufs: exit on first reported error
phy: samsung-ufs: ufs: remove superfluous mfd/syscon.h header
phy: rockchip: fix CONFIG_TYPEC dependency
phy: rockchip: usbdp: fix uninitialized variable
phy: rockchip-snps-pcie3: add support for rockchip,rx-common-refclk-mode
dt-bindings: phy: rockchip,pcie3-phy: add rockchip,rx-common-refclk-mode
phy: rockchip: add usbdp combo phy driver
dt-bindings: phy: add rockchip usbdp combo phy document
phy: add driver for MediaTek XFI T-PHY
dt-bindings: phy: mediatek,mt7988-xfi-tphy: add new bindings
phy: freescale: fsl-samsung-hdmi: Convert to platform remove callback returning void
phy: qcom: qmp-ufs: update SM8650 tables for Gear 4 & 5
MAINTAINERS: Add phy-gs101-ufs file to Tensor GS101.
...
Updates for v6.10
Core:
- Switched to generating register header files during build process
instead of shipping pre-generated headers
- Merged DPU and MDP4 format databases.
DP:
- Stop using compat string to distinguish DP and eDP cases
- Added support for X Elite platform (X1E80100)
- Reworked DP aux/audio support
- Added SM6350 DP to the bindings (no driver changes, using SM8350
as a fallback compat)
GPU:
- a7xx perfcntr reg fixes
- MAINTAINERS updates
- a750 devcoredump support
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGtpw6dNR9JBikFTQ=TCpt-9FeFW+SGjXWv+Jv3emm0Pbg@mail.gmail.com
