The enetc driver does not implement .ndo_change_mtu, instead it
configures the MAC register field PTC{Traffic Class}MSDUR[MAXSDU]
statically to a large value during probe time.
The driver used to configure only the max SDU for traffic class 0, and
that was fine while the driver could only use traffic class 0. But with
the introduction of mqprio, sending a large frame into any other TC than
0 is broken.
This patch fixes that by replicating per traffic class the static
configuration done in enetc_configure_port_mac().
Fixes: cbe9e835946f ("enetc: Enable TC offloading with mqprio")
Reported-by: Richie Pearn <richard.pearn@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: <Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20211020173340.1089992-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are two counters named "MAC tx frames", one of them is actually
incorrect. The correct name for that counter should be "MAC tx error
frames", which is symmetric to the existing "MAC rx error frames".
Fixes: 16eb4c85c964 ("enetc: Add ethtool statistics")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: <Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20211020165206.1069889-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use pci_info instead to avoid unnamed/uninitialized noise:
[197088.688729] sfc 0000:01:00.0: Solarflare NIC detected
[197088.690333] sfc 0000:01:00.0: Part Number : SFN5122F
[197088.729061] sfc 0000:01:00.0 (unnamed net_device) (uninitialized): no SR-IOV VFs probed
[197088.729071] sfc 0000:01:00.0 (unnamed net_device) (uninitialized): no PTP support
Inspired by fa44821a4ddd ("sfc: don't use netif_info et al before
net_device is registered") from Heiner Kallweit.
Signed-off-by: Erik Ekman <erik@kryo.se>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 1/10GbaseT modes were set up for cards with SFP+ cages in
3497ed8c852a5 ("sfc: report supported link speeds on SFP connections").
10GbaseT was likely used since no 10G fibre mode existed.
The missing fibre modes for 1/10G were added to ethtool.h in 5711a9822144
("net: ethtool: add support for 1000BaseX and missing 10G link modes")
shortly thereafter.
The user guide available at https://support-nic.xilinx.com/wp/drivers
lists support for the following cable and transceiver types in section 2.9:
- QSFP28 100G Direct Attach Cables
- QSFP28 100G SR Optical Transceivers (with SR4 modules listed)
- SFP28 25G Direct Attach Cables
- SFP28 25G SR Optical Transceivers
- QSFP+ 40G Direct Attach Cables
- QSFP+ 40G Active Optical Cables
- QSFP+ 40G SR4 Optical Transceivers
- QSFP+ to SFP+ Breakout Direct Attach Cables
- QSFP+ to SFP+ Breakout Active Optical Cables
- SFP+ 10G Direct Attach Cables
- SFP+ 10G SR Optical Transceivers
- SFP+ 10G LR Optical Transceivers
- SFP 1000BASE‐T Transceivers
- 1G Optical Transceivers
(From user guide issue 28. Issue 16 which also includes older cards like
SFN5xxx/SFN6xxx has matching lists for 1/10/40G transceiver types.)
Regarding SFP+ 10GBASE‐T transceivers the latest guide says:
"Solarflare adapters do not support 10GBASE‐T transceiver modules."
Tested using SFN5122F-R7 (with 2 SFP+ ports). Supported link modes do not change
depending on module used (tested with 1000BASE-T, 1000BASE-BX10, 10GBASE-LR).
Before:
$ ethtool ext
Settings for ext:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseT/Full
10000baseT/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Link partner advertised link modes: Not reported
Link partner advertised pause frame use: No
Link partner advertised auto-negotiation: No
Link partner advertised FEC modes: Not reported
Speed: 1000Mb/s
Duplex: Full
Auto-negotiation: off
Port: FIBRE
PHYAD: 255
Transceiver: internal
Current message level: 0x000020f7 (8439)
drv probe link ifdown ifup rx_err tx_err hw
Link detected: yes
After:
$ ethtool ext
Settings for ext:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseT/Full
1000baseX/Full
10000baseCR/Full
10000baseSR/Full
10000baseLR/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Link partner advertised link modes: Not reported
Link partner advertised pause frame use: No
Link partner advertised auto-negotiation: No
Link partner advertised FEC modes: Not reported
Speed: 1000Mb/s
Duplex: Full
Auto-negotiation: off
Port: FIBRE
PHYAD: 255
Transceiver: internal
Supports Wake-on: g
Wake-on: d
Current message level: 0x000020f7 (8439)
drv probe link ifdown ifup rx_err tx_err hw
Link detected: yes
Signed-off-by: Erik Ekman <erik@kryo.se>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current Work Queue Entry (WQE) checksum (csum) flags in the ethernet
segment (eseg) in case of IPsec crypto offload datapath are not aligned
with PRM/HW expectations.
Currently the driver always sets the l3_inner_csum flag in case of IPsec
because of the wrong usage of skb->encapsulation as indicator for inner
IPsec header since skb->encapsulation is always ON for IPsec packets
since IPsec itself is an encapsulation protocol. The above forced a
failing attempts of calculating csum of non-existing segments (like in
the IP|ESP|TCP packet case which does not have an l3_inner) which led
to lots of packet drops hence the low throughput.
Fix by using xo->inner_ipproto as indicator for inner IPsec header
instead of skb->encapsulation in addition to setting the csum flags
as following:
* Tunnel Mode:
* Pkt: MAC IP ESP IP L4
* CSUM: l3_cs | l3_inner_cs | l4_inner_cs
*
* Transport Mode:
* Pkt: MAC IP ESP L4
* CSUM: l3_cs [ | l4_cs (checksum partial case)]
*
* Tunnel(VXLAN TCP/UDP) over Transport Mode
* Pkt: MAC IP ESP UDP VXLAN IP L4
* CSUM: l3_cs | l3_inner_cs | l4_inner_cs
Fixes: f1267798c980 ("net/mlx5: Fix checksum issue of VXLAN and IPsec crypto offload")
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
IPsec crypto offload current Software Parser (SWP) fields settings in
the ethernet segment (eseg) are not aligned with PRM/HW expectations.
Among others in case of IP|ESP|TCP packet, current driver sets the
offsets for inner_l3 and inner_l4 although there is no inner l3/l4
headers relative to ESP header in such packets.
SWP provides the offsets for HW ,so it can be used to find csum fields
to offload the checksum, however these are not necessarily used by HW
and are used as fallback in case HW fails to parse the packet, e.g
when performing IPSec Transport Aware (IP | ESP | TCP) there is no
need to add SW parse on inner packet. So in some cases packets csum
was calculated correctly , whereas in other cases it failed. The later
faced csum errors (caused by wrong packet length calculations) which
led to lots of packet drops hence the low throughput.
Fix by setting the SWP fields as expected in a IP|ESP|TCP packet.
the following describe the expected SWP offsets:
* Tunnel Mode:
* SWP: OutL3 InL3 InL4
* Pkt: MAC IP ESP IP L4
*
* Transport Mode:
* SWP: OutL3 OutL4
* Pkt: MAC IP ESP L4
*
* Tunnel(VXLAN TCP/UDP) over Transport Mode
* SWP: OutL3 InL3 InL4
* Pkt: MAC IP ESP UDP VXLAN IP L4
Fixes: f1267798c980 ("net/mlx5: Fix checksum issue of VXLAN and IPsec crypto offload")
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
During suspend flow the driver calls mlx5e_destroy_vlan_table() which
does not only delete the vlans steering flow rules, but also frees the
data on currently active vlans, thus it is not restored during resume
flow.
This fix keeps the vlan data on suspend flow and frees it only on driver
remove flow.
Fixes: 6783f0a21a3c ("net/mlx5e: Dynamic alloc vlan table for netdev when needed")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Dan Carpenter report:
The patch f47e04eb96e0: "net/mlx5: E-switch, Allow setting share/max
tx rate limits of rate groups" from May 31, 2021, leads to the
following Smatch static checker warning:
drivers/net/ethernet/mellanox/mlx5/core/esw/qos.c:483 esw_qos_create_rate_group()
warn: passing zero to 'ERR_PTR'
If min rate normalization failed then error code may be overwritten to 0
if scheduling element destruction succeed. Ignore this value and always
return initial one.
Fixes: f47e04eb96e0 ("net/mlx5: E-switch, Allow setting share/max tx rate limits of rate groups")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Both multipath and bonding events are changing the HW LAG state
independently.
Handling one of the features events while the other is already
enabled can cause unwanted behavior, for example handling
bonding event while multipath enabled will disable the lag and
cause multipath to stop working.
Fix it by ignoring bonding event while in multipath and ignoring FIB
events while in bonding mode.
Fixes: 544fe7c2e654 ("net/mlx5e: Activate HW multipath and handle port affinity based on FIB events")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
As part of support for E810 XXV devices, some device ids were
inadvertently left out. Add those missing ids.
Fixes: 195fb97766da ("ice: add additional E810 device id")
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
The device ID for I226_K was incorrectly assigned, update the device
ID to the correct one.
Fixes: bfa5e98c9de4 ("igc: Add new device ID")
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Update the HW MAC initialization flow. Do not gate DMA clock from
the modPHY block. Keeping this clock will prevent dropped packets
sent in burst mode on the Kumeran interface.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=213651
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=213377
Fixes: fb776f5d57ee ("e1000e: Add support for Tiger Lake")
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Mark Pearson <markpearson@lenovo.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
We have the same LAN controller on different PCHs. Separate TGP board
type from SPT which will allow for specific fixes to be applied for
TGP platforms.
Suggested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Mark Pearson <markpearson@lenovo.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When utilizing End to End delay mechanism, the following error messages show up:
|root@ehl1:~# ptp4l --tx_timestamp_timeout=50 -H -i eno2 -E -m
|ptp4l[950.573]: selected /dev/ptp3 as PTP clock
|ptp4l[950.586]: port 1: INITIALIZING to LISTENING on INIT_COMPLETE
|ptp4l[950.586]: port 0: INITIALIZING to LISTENING on INIT_COMPLETE
|ptp4l[952.879]: port 1: new foreign master 001395.fffe.4897b4-1
|ptp4l[956.879]: selected best master clock 001395.fffe.4897b4
|ptp4l[956.879]: port 1: assuming the grand master role
|ptp4l[956.879]: port 1: LISTENING to GRAND_MASTER on RS_GRAND_MASTER
|ptp4l[962.017]: port 1: received DELAY_REQ without timestamp
|ptp4l[962.273]: port 1: received DELAY_REQ without timestamp
|ptp4l[963.090]: port 1: received DELAY_REQ without timestamp
Commit f2fb6b6275eb ("net: stmmac: enable timestamp snapshot for required PTP
packets in dwmac v5.10a") already addresses this problem for the dwmac
v5.10. However, same holds true for all dwmacs above version v4.10. Correct the
check accordingly. Afterwards everything works as expected.
Tested on Intel Atom(R) x6414RE Processor.
Fixes: 14f347334bf2 ("net: stmmac: Correctly take timestamp for PTPv2")
Fixes: f2fb6b6275eb ("net: stmmac: enable timestamp snapshot for required PTP packets in dwmac v5.10a")
Suggested-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
HNS3 driver includes hns3.ko, hnae3.ko and hclge.ko.
hns3.ko includes network stack and pci_driver, hclge.ko includes
HW device action, algo_ops and timer task, hnae3.ko includes some
register function.
When SRIOV is enable and hclge.ko is removed, HW device is unloaded
but VF still exists, PF will not reply VF mbx messages, and cause
errors.
This patch fix it by disable SRIOV before remove hclge.ko.
Fixes: e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The task of VF reset is performed through the workqueue. It checks the
value of hdev->reset_pending to determine whether to exit the loop.
However, the value of hdev->reset_pending may also be assigned by
the interrupt function hclgevf_misc_irq_handle(), which may cause the
loop fail to exit and keep occupying the workqueue. This loop is not
necessary, so remove it and the workqueue will be rescheduled if the
reset needs to be retried or a new reset occurs.
Fixes: 1cc9bc6e5867 ("net: hns3: split hclgevf_reset() into preparing and rebuilding part")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when there is a rx page allocation failure, it is
possible that polling may be stopped if there is no more packet
to be reveiced, which may cause queue stall problem under memory
pressure.
This patch makes sure polling is scheduled again when there is
any rx page allocation failure, and polling will try to allocate
receive buffers until it succeeds.
Now the allocation retry is added, it is unnecessary to do the rx
page allocation at the end of rx cleaning, so remove it. And reset
the unused_count to zero after calling hns3_nic_alloc_rx_buffers()
to avoid calling hns3_nic_alloc_rx_buffers() repeatedly under
memory pressure.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rx unused desc is the desc that need attatching new buffer
before refilling to hw to receive new packet, the number of
desc need attatching new buffer is calculated using next_to_use
and next_to_clean. when next_to_use == next_to_clean, currently
hns3 driver assumes that all the desc has the buffer attatched,
but 'next_to_use == next_to_clean' also means all the desc need
attatching new buffer if hw has comsumed all the desc and the
driver has not attatched any buffer to the desc yet.
This patch adds 'refill' in desc_cb to indicate whether a new
buffer has been refilled to a desc.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the max tx size supported by the hw is calculated by
using the max BD num supported by the hw. According to the hw
user manual, the max tx size is fixed value for both non-TSO and
TSO skb.
This patch updates the max tx size according to the manual.
Fixes: 8ae10cfb5089("net: hns3: support tx-scatter-gather-fraglist feature")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If ets dwrr bandwidth of tc is set to 0, the hardware will switch to SP
mode. In this case, this tc may occupy all the tx bandwidth if it has
huge traffic, so it violates the purpose of the user setting.
To fix this problem, limit the ets dwrr bandwidth must greater than 0.
Fixes: cacde272dd00 ("net: hns3: Add hclge_dcb module for the support of DCB feature")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, DWRR of tc will be initialized to a fixed value when this tc
is enabled, but it is not been reset to 0 when this tc is disabled. It
cause a problem that the DWRR of unused tc is not 0 after using tc tool
to add and delete multi-tc parameters.
For examples, after enabling 4 TCs and restoring to 1 TC by follow
tc commands:
$ tc qdisc add dev eth0 root mqprio num_tc 4 map 0 1 2 3 0 1 2 3 queues \
8@0 8@8 8@16 8@24 hw 1 mode channel
$ tc qdisc del dev eth0 root
Now there is just one TC is enabled for eth0, but the tc info querying by
debugfs is shown as follow:
$ cat /mnt/hns3/0000:7d:00.0/tm/tc_sch_info
enabled tc number: 1
weight_offset: 14
TC MODE WEIGHT
0 dwrr 100
1 dwrr 100
2 dwrr 100
3 dwrr 100
4 dwrr 0
5 dwrr 0
6 dwrr 0
7 dwrr 0
This patch fixes it by resetting DWRR of tc to 0 when tc is disabled.
Fixes: 848440544b41 ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add configuration of interrupt type and fifo interrupt enable of TM QCN
error event if enabled, otherwise this event will not be reported when
there is error.
Fixes: d914971df022 ("net: hns3: remove redundant query in hclge_config_tm_hw_err_int()")
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 09e856d54bda5f288ef8437a90ab2b9b3eab83d1.
When an interface is enslaved in a VRF, prerouting conntrack hook is
called twice: once in the context of the original input interface, and
once in the context of the VRF interface. If no special precausions are
taken, this leads to creation of two conntrack entries instead of one,
and breaks SNAT.
Commit above was intended to avoid creation of extra conntrack entries
when input interface is enslaved in a VRF. It did so by resetting
conntrack related data associated with the skb when it enters VRF context.
However it breaks netfilter operation. Imagine a use case when conntrack
zone must be assigned based on the original input interface, rather than
VRF interface (that would make original interfaces indistinguishable). One
could create netfilter rules similar to these:
chain rawprerouting {
type filter hook prerouting priority raw;
iif realiface1 ct zone set 1 return
iif realiface2 ct zone set 2 return
}
This works before the mentioned commit, but not after: zone assignment
is "forgotten", and any subsequent NAT or filtering that is dependent
on the conntrack zone does not work.
Here is a reproducer script that demonstrates the difference in behaviour.
==========
#!/bin/sh
# This script demonstrates unexpected change of nftables behaviour
# caused by commit 09e856d54bda5f28 ""vrf: Reset skb conntrack
# connection on VRF rcv"
# https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=09e856d54bda5f288ef8437a90ab2b9b3eab83d1
#
# Before the commit, it was possible to assign conntrack zone to a
# packet (or mark it for `notracking`) in the prerouting chanin, raw
# priority, based on the `iif` (interface from which the packet
# arrived).
# After the change, # if the interface is enslaved in a VRF, such
# assignment is lost. Instead, assignment based on the `iif` matching
# the VRF master interface is honored. Thus it is impossible to
# distinguish packets based on the original interface.
#
# This script demonstrates this change of behaviour: conntrack zone 1
# or 2 is assigned depending on the match with the original interface
# or the vrf master interface. It can be observed that conntrack entry
# appears in different zone in the kernel versions before and after
# the commit.
IPIN=172.30.30.1
IPOUT=172.30.30.2
PFXL=30
ip li sh vein >/dev/null 2>&1 && ip li del vein
ip li sh tvrf >/dev/null 2>&1 && ip li del tvrf
nft list table testct >/dev/null 2>&1 && nft delete table testct
ip li add vein type veth peer veout
ip li add tvrf type vrf table 9876
ip li set veout master tvrf
ip li set vein up
ip li set veout up
ip li set tvrf up
/sbin/sysctl -w net.ipv4.conf.veout.accept_local=1
/sbin/sysctl -w net.ipv4.conf.veout.rp_filter=0
ip addr add $IPIN/$PFXL dev vein
ip addr add $IPOUT/$PFXL dev veout
nft -f - <<__END__
table testct {
chain rawpre {
type filter hook prerouting priority raw;
iif { veout, tvrf } meta nftrace set 1
iif veout ct zone set 1 return
iif tvrf ct zone set 2 return
notrack
}
chain rawout {
type filter hook output priority raw;
notrack
}
}
__END__
uname -rv
conntrack -F
ping -W 1 -c 1 -I vein $IPOUT
conntrack -L
Signed-off-by: Eugene Crosser <crosser@average.org>
Acked-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the process of driver probing, the probe function should return < 0
for failure, otherwise, the kernel will treat value > 0 as success.
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A new warning in clang points out two places in this driver where
boolean expressions are being used with a bitwise OR instead of a
logical one:
drivers/net/ethernet/netronome/nfp/nfp_asm.c:199:20: error: use of bitwise '|' with boolean operands [-Werror,-Wbitwise-instead-of-logical]
reg->src_lmextn = swreg_lmextn(lreg) | swreg_lmextn(rreg);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
||
drivers/net/ethernet/netronome/nfp/nfp_asm.c:199:20: note: cast one or both operands to int to silence this warning
drivers/net/ethernet/netronome/nfp/nfp_asm.c:280:20: error: use of bitwise '|' with boolean operands [-Werror,-Wbitwise-instead-of-logical]
reg->src_lmextn = swreg_lmextn(lreg) | swreg_lmextn(rreg);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
||
drivers/net/ethernet/netronome/nfp/nfp_asm.c:280:20: note: cast one or both operands to int to silence this warning
2 errors generated.
The motivation for the warning is that logical operations short circuit
while bitwise operations do not. In this case, it does not seem like
short circuiting is harmful so implement the suggested fix of changing
to a logical operation to fix the warning.
Link: https://github.com/ClangBuiltLinux/linux/issues/1479
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20211018193101.2340261-1-nathan@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
During the process of driver probing, the probe function should return < 0
for failure, otherwise, the kernel will treat value > 0 as success.
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix following coccicheck warning:
./drivers/net/ethernet/mscc/ocelot_vsc7514.c:946:1-33: WARNING: Function
for_each_available_child_of_node should have of_node_put() before goto.
Early exits from for_each_available_child_of_node should decrement the
node reference counter.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix following coccicheck warning:
./drivers/net/ethernet/microchip/sparx5/s4parx5_main.c:723:1-33: WARNING: Function
for_each_available_child_of_node should have of_node_put() before goto
Early exits from for_each_available_child_of_node should decrement the
node reference counter.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting ds->num_ports to DSA_MAX_PORTS made DSA core allocate unnecessary
dsa_port's and call mt7530_port_disable for non-existent ports.
Set it to MT7530_NUM_PORTS to fix that, and dsa_is_user_port check in
port_enable/disable is no longer required.
Cc: stable@vger.kernel.org
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I compared the register definitions with the D-Link DWR-966
GPL sources and found that the PUAFD field definition was
incorrect. This definition is unused and causes no issues.
Fixes: 14fceff4771e ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEK3kIWJt9yTYMP3ehqclaivrt76kFAmFsjT8THG1rbEBwZW5n
dXRyb25peC5kZQAKCRCpyVqK+u3vqXJNCACBFemjdVEKUaWEjd10YvHaILdnEkge
6bj51eIpYy/aAfIqGLhhUOYiyVRlrTD4phJBSVl25jx0Vaf6UqXQ6Otd3GjJAV7j
16Hp8EvGc14cnx+rCPU471YUWyTrPl7YU9AoYKeBmbRmwh4i6HiJZ75AbG6xGvE8
2JZLmrF0QvpZRFfxE0uF5oVwjP9tOSvDmuFa6Me/JQ30CBrpxSalayizMvCO27eO
k2PaXSCpfms2K2eSBTqcjcqjJV57izJzNVtPkcmgOcyB1gvbBmHD7Y2GiiJ6Uigg
YkVEscsZNE1Wn/5p+sIS3pKDErsCsTgiAaopxCiaEsMLdv8b7HLecRGN
=CfwZ
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-5.15-20211017' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2021-10-17
this is a pull request of 11 patches for net/master.
The first 4 patches are by Ziyang Xuan and Zhang Changzhong and fix 1
use after free and 3 standard conformance problems in the j1939 CAN
stack.
The next 2 patches are by Ziyang Xuan and fix 2 concurrency problems
in the ISOTP CAN stack.
Yoshihiro Shimoda's patch for the rcar_can fix suspend/resume on not
running CAN interfaces.
Aswath Govindraju's patch for the m_can driver fixes access for MMIO
devices.
Zheyu Ma contributes a patch for the peak_pci driver to fix a use
after free.
Stephane Grosjean's 2 patches fix CAN error state handling in the
peak_usb driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
On i386, the baycom_epp driver wants to inspect X86 CPU features (TSC)
and then act on that data, but that info is not available when running
on UML, so prevent that test and do the default action.
Prevents this build error on UML + i386:
../drivers/net/hamradio/baycom_epp.c: In function ‘epp_bh’:
../drivers/net/hamradio/baycom_epp.c:630:6: error: implicit declaration of function ‘boot_cpu_has’; did you mean ‘get_cpu_mask’? [-Werror=implicit-function-declaration]
if (boot_cpu_has(X86_FEATURE_TSC)) \
^
../drivers/net/hamradio/baycom_epp.c:658:2: note: in expansion of macro ‘GETTICK’
GETTICK(time1);
Fixes: 68f5d3f3b654 ("um: add PCI over virtio emulation driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: linux-um@lists.infradead.org
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Thomas Sailer <t.sailer@alumni.ethz.ch>
Cc: linux-hams@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Since alloc_can_err_skb() puts NULL in cf in the case when skb cannot
be allocated and can_change_state() handles the case when cf is NULL,
the test on the nullity of skb is now unnecessary.
Link: https://lore.kernel.org/all/20210929142111.55757-2-s.grosjean@peak-system.com
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This corrects the lack of notification of a return to ERROR_ACTIVE
state for USB - CANFD devices from PEAK-System.
Fixes: 0a25e1f4f185 ("can: peak_usb: add support for PEAK new CANFD USB adapters")
Link: https://lore.kernel.org/all/20210929142111.55757-1-s.grosjean@peak-system.com
Cc: stable@vger.kernel.org
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The read and writes from the fifo are from a buffer, with various
fields and data at predefined offsets. So, they should not be done to
the same address(or port) in case of val_count greater than 1.
Therefore, fix this by using iowrite32()/ioread32() instead of
ioread32_rep()/iowrite32_rep().
Also, the write into FIFO must be performed with an offset from the
message ram base address. Therefore, fix the base address to
mram_base.
Fixes: e39381770ec9 ("can: m_can: Disable IRQs on FIFO bus errors")
Link: https://lore.kernel.org/all/20210920123344.2320-1-a-govindraju@ti.com
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If the driver was not opened, rcar_can_suspend() should not call
clk_disable() because the clock was not enabled.
Fixes: fd1159318e55 ("can: add Renesas R-Car CAN driver")
Link: https://lore.kernel.org/all/20210924075556.223685-1-yoshihiro.shimoda.uh@renesas.com
Cc: stable@vger.kernel.org
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Ayumi Nakamichi <ayumi.nakamichi.kf@renesas.com>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Tested-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2021-10-14
Brett ensures RDMA nodes are removed during release and rebuild. He also
corrects fw.mgmt.api to include the patch number for proper
identification.
Dave stops ida_free() being called when an IDA has not been allocated.
Michal corrects the order of parameters being provided and the number of
entries skipped for UDP tunnels.
====================
Link: https://lore.kernel.org/r/20211014181953.3538330-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix the following build/link error by adding a dependency on the CRC32
routines:
ld: drivers/net/usb/lan78xx.o: in function `lan78xx_set_multicast':
lan78xx.c:(.text+0x48cf): undefined reference to `crc32_le'
The actual use of crc32_le() comes indirectly through ether_crc().
Fixes: 55d7de9de6c30 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current release - regressions:
- af_unix: rename UNIX-DGRAM to UNIX to maintain backwards compatibility
- procfs: revert "add seq_puts() statement for dev_mcast",
minor format change broke user space
Current release - new code bugs:
- dsa: fix bridge_num not getting cleared after ports leaving
the bridge, resource leak
- dsa: tag_dsa: send packets with TX fwd offload from VLAN-unaware
bridges using VID 0, prevent packet drops if pvid is removed
- dsa: mv88e6xxx: keep the pvid at 0 when VLAN-unaware, prevent
HW getting confused about station to VLAN mapping
Previous releases - regressions:
- virtio-net: fix for skb_over_panic inside big mode
- phy: do not shutdown PHYs in READY state
- dsa: mv88e6xxx: don't use PHY_DETECT on internal PHY's,
fix link LED staying lit after ifdown
- mptcp: fix possible infinite wait on recvmsg(MSG_WAITALL)
- mqprio: Correct stats in mqprio_dump_class_stats()
- ice: fix deadlock for Tx timestamp tracking flush
- stmmac: fix feature detection on old hardware
Previous releases - always broken:
- sctp: account stream padding length for reconf chunk
- icmp: fix icmp_ext_echo_iio parsing in icmp_build_probe()
- isdn: cpai: check ctr->cnr to avoid array index out of bound
- isdn: mISDN: fix sleeping function called from invalid context
- nfc: nci: fix potential UAF of rf_conn_info object
- dsa: microchip: prevent ksz_mib_read_work from kicking back
in after it's canceled in .remove and crashing
- dsa: mv88e6xxx: isolate the ATU databases of standalone and
bridged ports
- dsa: sja1105, ocelot: break circular dependency between switch
and tag drivers
- dsa: felix: improve timestamping in presence of packe loss
- mlxsw: thermal: fix out-of-bounds memory accesses
Misc:
- ipv6: ioam: move the check for undefined bits to improve
interoperability
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=/K9E
-----END PGP SIGNATURE-----
Merge tag 'net-5.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Quite calm.
The noisy DSA driver (embedded switches) changes, and adjustment to
IPv6 IOAM behavior add to diffstat's bottom line but are not scary.
Current release - regressions:
- af_unix: rename UNIX-DGRAM to UNIX to maintain backwards
compatibility
- procfs: revert "add seq_puts() statement for dev_mcast", minor
format change broke user space
Current release - new code bugs:
- dsa: fix bridge_num not getting cleared after ports leaving the
bridge, resource leak
- dsa: tag_dsa: send packets with TX fwd offload from VLAN-unaware
bridges using VID 0, prevent packet drops if pvid is removed
- dsa: mv88e6xxx: keep the pvid at 0 when VLAN-unaware, prevent HW
getting confused about station to VLAN mapping
Previous releases - regressions:
- virtio-net: fix for skb_over_panic inside big mode
- phy: do not shutdown PHYs in READY state
- dsa: mv88e6xxx: don't use PHY_DETECT on internal PHY's, fix link
LED staying lit after ifdown
- mptcp: fix possible infinite wait on recvmsg(MSG_WAITALL)
- mqprio: Correct stats in mqprio_dump_class_stats()
- ice: fix deadlock for Tx timestamp tracking flush
- stmmac: fix feature detection on old hardware
Previous releases - always broken:
- sctp: account stream padding length for reconf chunk
- icmp: fix icmp_ext_echo_iio parsing in icmp_build_probe()
- isdn: cpai: check ctr->cnr to avoid array index out of bound
- isdn: mISDN: fix sleeping function called from invalid context
- nfc: nci: fix potential UAF of rf_conn_info object
- dsa: microchip: prevent ksz_mib_read_work from kicking back in
after it's canceled in .remove and crashing
- dsa: mv88e6xxx: isolate the ATU databases of standalone and bridged
ports
- dsa: sja1105, ocelot: break circular dependency between switch and
tag drivers
- dsa: felix: improve timestamping in presence of packe loss
- mlxsw: thermal: fix out-of-bounds memory accesses
Misc:
- ipv6: ioam: move the check for undefined bits to improve
interoperability"
* tag 'net-5.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (60 commits)
icmp: fix icmp_ext_echo_iio parsing in icmp_build_probe
MAINTAINERS: Update the devicetree documentation path of imx fec driver
sctp: account stream padding length for reconf chunk
mlxsw: thermal: Fix out-of-bounds memory accesses
ethernet: s2io: fix setting mac address during resume
NFC: digital: fix possible memory leak in digital_in_send_sdd_req()
NFC: digital: fix possible memory leak in digital_tg_listen_mdaa()
nfc: fix error handling of nfc_proto_register()
Revert "net: procfs: add seq_puts() statement for dev_mcast"
net: encx24j600: check error in devm_regmap_init_encx24j600
net: korina: select CRC32
net: arc: select CRC32
net: dsa: felix: break at first CPU port during init and teardown
net: dsa: tag_ocelot_8021q: fix inability to inject STP BPDUs into BLOCKING ports
net: dsa: felix: purge skb from TX timestamping queue if it cannot be sent
net: dsa: tag_ocelot_8021q: break circular dependency with ocelot switch lib
net: dsa: tag_ocelot: break circular dependency with ocelot switch lib driver
net: mscc: ocelot: cross-check the sequence id from the timestamp FIFO with the skb PTP header
net: mscc: ocelot: deny TX timestamping of non-PTP packets
net: mscc: ocelot: warn when a PTP IRQ is raised for an unknown skb
...
Currently when a user uses "devlink dev info", the fw.mgmt.api will be
the major.minor numbers as shown below:
devlink dev info pci/0000:3b:00.0
pci/0000:3b:00.0:
driver ice
serial_number 00-01-00-ff-ff-00-00-00
versions:
fixed:
board.id K91258-000
running:
fw.mgmt 6.1.2
fw.mgmt.api 1.7 <--- No patch number included
fw.mgmt.build 0xd75e7d06
fw.mgmt.srev 5
fw.undi 1.2992.0
fw.undi.srev 5
fw.psid.api 3.10
fw.bundle_id 0x800085cc
fw.app.name ICE OS Default Package
fw.app 1.3.27.0
fw.app.bundle_id 0xc0000001
fw.netlist 3.10.2000-3.1e.0
fw.netlist.build 0x2a76e110
stored:
fw.mgmt.srev 5
fw.undi 1.2992.0
fw.undi.srev 5
fw.psid.api 3.10
fw.bundle_id 0x800085cc
fw.netlist 3.10.2000-3.1e.0
fw.netlist.build 0x2a76e110
There are many features in the driver that depend on the major, minor,
and patch version of the FW. Without the patch number in the output for
fw.mgmt.api debugging issues related to the FW API version is difficult.
Also, using major.minor.patch aligns with the existing firmware version
which uses a 3 digit value.
Fix this by making the fw.mgmt.api print the major.minor.patch
versions. Shown below is the result:
devlink dev info pci/0000:3b:00.0
pci/0000:3b:00.0:
driver ice
serial_number 00-01-00-ff-ff-00-00-00
versions:
fixed:
board.id K91258-000
running:
fw.mgmt 6.1.2
fw.mgmt.api 1.7.9 <--- patch number included
fw.mgmt.build 0xd75e7d06
fw.mgmt.srev 5
fw.undi 1.2992.0
fw.undi.srev 5
fw.psid.api 3.10
fw.bundle_id 0x800085cc
fw.app.name ICE OS Default Package
fw.app 1.3.27.0
fw.app.bundle_id 0xc0000001
fw.netlist 3.10.2000-3.1e.0
fw.netlist.build 0x2a76e110
stored:
fw.mgmt.srev 5
fw.undi 1.2992.0
fw.undi.srev 5
fw.psid.api 3.10
fw.bundle_id 0x800085cc
fw.netlist 3.10.2000-3.1e.0
fw.netlist.build 0x2a76e110
Fixes: ff2e5c700e08 ("ice: add basic handler for devlink .info_get")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Correct parameters order in call to ice_tunnel_idx_to_entry function.
Entry in sparse port table is correct when the idx is 0. For idx 1 one
correct entry should be skipped, for idx 2 two of them should be skipped
etc. Change if condition to be true when idx is 0, which means that
previous valid entry of this tunnel type were skipped.
Fixes: b20e6c17c468 ("ice: convert to new udp_tunnel infrastructure")
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In the remove path, there is an attempt to free the aux_idx IDA whether
it was allocated or not. This can potentially cause a crash when
unloading the driver on systems that do not initialize support for RDMA.
But, this free cannot be gated by the status bit for RDMA, since it is
allocated if the driver detects support for RDMA at probe time, but the
driver can enter into a state where RDMA is not supported after the IDA
has been allocated at probe time and this would lead to a memory leak.
Initialize aux_idx to an invalid value and check for a valid value when
unloading to determine if an IDA free is necessary.
Fixes: d25a0fc41c1f9 ("ice: Initialize RDMA support")
Reported-by: Jun Miao <jun.miao@windriver.com>
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently if the VSI is rebuilt/removed and the RDMA PF driver is active
the RDMA Tx queue scheduler node configuration will not be cleaned up.
This will cause the rebuild/re-add of the VSI to fail due to the
software structures not being correctly cleaned up for the VSI index.
Fix this by always calling ice_rm_vsi_rdma_cfg() for all VSI. If there
are no RDMA scheduler nodes created, then there is no harm in calling
ice_rm_vsi_rdma_cfg(). This change applies to all VSI types, so if
RDMA support is added for other VSI types they will also get this
change.
Fixes: 348048e724a0 ("ice: Implement iidc operations")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Jerzy Wiktor Jurkowski <jerzy.wiktor.jurkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, mlxsw allows cooling states to be set above the maximum
cooling state supported by the driver:
# cat /sys/class/thermal/thermal_zone2/cdev0/type
mlxsw_fan
# cat /sys/class/thermal/thermal_zone2/cdev0/max_state
10
# echo 18 > /sys/class/thermal/thermal_zone2/cdev0/cur_state
# echo $?
0
This results in out-of-bounds memory accesses when thermal state
transition statistics are enabled (CONFIG_THERMAL_STATISTICS=y), as the
transition table is accessed with a too large index (state) [1].
According to the thermal maintainer, it is the responsibility of the
driver to reject such operations [2].
Therefore, return an error when the state to be set exceeds the maximum
cooling state supported by the driver.
To avoid dead code, as suggested by the thermal maintainer [3],
partially revert commit a421ce088ac8 ("mlxsw: core: Extend cooling
device with cooling levels") that tried to interpret these invalid
cooling states (above the maximum) in a special way. The cooling levels
array is not removed in order to prevent the fans going below 20% PWM,
which would cause them to get stuck at 0% PWM.
[1]
BUG: KASAN: slab-out-of-bounds in thermal_cooling_device_stats_update+0x271/0x290
Read of size 4 at addr ffff8881052f7bf8 by task kworker/0:0/5
CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted 5.15.0-rc3-custom-45935-gce1adf704b14 #122
Hardware name: Mellanox Technologies Ltd. "MSN2410-CB2FO"/"SA000874", BIOS 4.6.5 03/08/2016
Workqueue: events_freezable_power_ thermal_zone_device_check
Call Trace:
dump_stack_lvl+0x8b/0xb3
print_address_description.constprop.0+0x1f/0x140
kasan_report.cold+0x7f/0x11b
thermal_cooling_device_stats_update+0x271/0x290
__thermal_cdev_update+0x15e/0x4e0
thermal_cdev_update+0x9f/0xe0
step_wise_throttle+0x770/0xee0
thermal_zone_device_update+0x3f6/0xdf0
process_one_work+0xa42/0x1770
worker_thread+0x62f/0x13e0
kthread+0x3ee/0x4e0
ret_from_fork+0x1f/0x30
Allocated by task 1:
kasan_save_stack+0x1b/0x40
__kasan_kmalloc+0x7c/0x90
thermal_cooling_device_setup_sysfs+0x153/0x2c0
__thermal_cooling_device_register.part.0+0x25b/0x9c0
thermal_cooling_device_register+0xb3/0x100
mlxsw_thermal_init+0x5c5/0x7e0
__mlxsw_core_bus_device_register+0xcb3/0x19c0
mlxsw_core_bus_device_register+0x56/0xb0
mlxsw_pci_probe+0x54f/0x710
local_pci_probe+0xc6/0x170
pci_device_probe+0x2b2/0x4d0
really_probe+0x293/0xd10
__driver_probe_device+0x2af/0x440
driver_probe_device+0x51/0x1e0
__driver_attach+0x21b/0x530
bus_for_each_dev+0x14c/0x1d0
bus_add_driver+0x3ac/0x650
driver_register+0x241/0x3d0
mlxsw_sp_module_init+0xa2/0x174
do_one_initcall+0xee/0x5f0
kernel_init_freeable+0x45a/0x4de
kernel_init+0x1f/0x210
ret_from_fork+0x1f/0x30
The buggy address belongs to the object at ffff8881052f7800
which belongs to the cache kmalloc-1k of size 1024
The buggy address is located 1016 bytes inside of
1024-byte region [ffff8881052f7800, ffff8881052f7c00)
The buggy address belongs to the page:
page:0000000052355272 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x1052f0
head:0000000052355272 order:3 compound_mapcount:0 compound_pincount:0
flags: 0x200000000010200(slab|head|node=0|zone=2)
raw: 0200000000010200 ffffea0005034800 0000000300000003 ffff888100041dc0
raw: 0000000000000000 0000000000100010 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff8881052f7a80: 00 00 00 00 00 00 04 fc fc fc fc fc fc fc fc fc
ffff8881052f7b00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff8881052f7b80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
^
ffff8881052f7c00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff8881052f7c80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[2] https://lore.kernel.org/linux-pm/9aca37cb-1629-5c67-1895-1fdc45c0244e@linaro.org/
[3] https://lore.kernel.org/linux-pm/af9857f2-578e-de3a-e62b-6baff7e69fd4@linaro.org/
CC: Daniel Lezcano <daniel.lezcano@linaro.org>
Fixes: a50c1e35650b ("mlxsw: core: Implement thermal zone")
Fixes: a421ce088ac8 ("mlxsw: core: Extend cooling device with cooling levels")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20211012174955.472928-1-idosch@idosch.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After recent cleanups, gcc started warning about a suspicious
memcpy() call during the s2io_io_resume() function:
In function '__dev_addr_set',
inlined from 'eth_hw_addr_set' at include/linux/etherdevice.h:318:2,
inlined from 's2io_set_mac_addr' at drivers/net/ethernet/neterion/s2io.c:5205:2,
inlined from 's2io_io_resume' at drivers/net/ethernet/neterion/s2io.c:8569:7:
arch/x86/include/asm/string_32.h:182:25: error: '__builtin_memcpy' accessing 6 bytes at offsets 0 and 2 overlaps 4 bytes at offset 2 [-Werror=restrict]
182 | #define memcpy(t, f, n) __builtin_memcpy(t, f, n)
| ^~~~~~~~~~~~~~~~~~~~~~~~~
include/linux/netdevice.h:4648:9: note: in expansion of macro 'memcpy'
4648 | memcpy(dev->dev_addr, addr, len);
| ^~~~~~
What apparently happened is that an old cleanup changed the calling
conventions for s2io_set_mac_addr() from taking an ethernet address
as a character array to taking a struct sockaddr, but one of the
callers was not changed at the same time.
Change it to instead call the low-level do_s2io_prog_unicast() function
that still takes the old argument type.
Fixes: 2fd376884558 ("S2io: Added support set_mac_address driver entry point")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20211013143613.2049096-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
