All remaining skbs should be released when myri10ge_xmit fails to
transmit a packet. Fix it within another skb_list_walk_safe.
Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
aqc111_rx_fixup() contains several out-of-bounds accesses that can be
triggered by a malicious (or defective) USB device, in particular:
- The metadata array (desc_offset..desc_offset+2*pkt_count) can be out of bounds,
causing OOB reads and (on big-endian systems) OOB endianness flips.
- A packet can overlap the metadata array, causing a later OOB
endianness flip to corrupt data used by a cloned SKB that has already
been handed off into the network stack.
- A packet SKB can be constructed whose tail is far beyond its end,
causing out-of-bounds heap data to be considered part of the SKB's
data.
Found doing variant analysis. Tested it with another driver (ax88179_178a), since
I don't have a aqc111 device to test it, but the code looks very similar.
Signed-off-by: Marcin Kozlowski <marcinguy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qede_build_skb() assumes build_skb() always works and goes straight
to skb_reserve(). However, build_skb() can fail under memory pressure.
This results in a kernel panic because the skb to reserve is NULL.
Add a check in case build_skb() failed to allocate and return NULL.
The NULL return is handled correctly in callers to qede_build_skb().
Fixes: 8a8633978b842 ("qede: Add build_skb() support.")
Signed-off-by: Jamie Bainbridge <jamie.bainbridge@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/ipv6/ip6mr.c:1656:14: warning: unused variable 'do_wrmifwhole'
Move it to the CONFIG_IPV6_PIMSM_V2 scope where its used.
Fixes: 4b340a5a726d ("net: ip6mr: add support for passing full packet on wrong mif")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-04-05
Maciej Fijalkowski says:
We were solving issues around AF_XDP busy poll's not-so-usual scenarios,
such as very big busy poll budgets applied to very small HW rings. This
set carries the things that were found during that work that apply to
net tree.
One thing that was fixed for all in-tree ZC drivers was missing on ice
side all the time - it's about syncing RCU before destroying XDP
resources. Next one fixes the bit that is checked in ice_xsk_wakeup and
third one avoids false setting of DD bits on Tx descriptors.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver doesn't support clause 45 register access yet, but doesn't
check if the access is a c45 one either. This leads to spurious register
reads and writes. Add the check.
Fixes: 542671fe4d86 ("net: phy: mscc-miim: Add MDIO driver")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Chiu says:
====================
Fix broken link on Xilinx's AXI Ethernet in SGMII mode
The Ethernet driver use phy-handle to reference the PCS/PMA PHY. This
could be a problem if one wants to configure an external PHY via phylink,
since it use the same phandle to get the PHY. To fix this, introduce a
dedicated pcs-handle to point to the PCS/PMA PHY and deprecate the use
of pointing it with phy-handle. A similar use case of pcs-handle can be
seen on dpaa2 as well.
--- patch v5 ---
- Re-apply the v4 patch on the net tree.
- Describe the pcs-handle DT binding at ethernet-controller level.
--- patch v6 ---
- Remove "preferrably" to clearify usage of pcs_handle.
--- patch v7 ---
- Rebase the patch on latest net/master
--- patch v8 ---
- Rebase the patch on net-next/master
- Add "reviewed-by" tag in PATCH 3/4: dt-bindings: net: add pcs-handle
attribute
- Remove "fix" tag in last commit message since this is not a critical
bug and will not be back ported to stable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In some SGMII use cases where both a fixed link external PHY and the
internal PCS/PMA PHY need to be configured, we should explicitly use a
phandle "pcs-phy" to get the reference to the PCS/PMA PHY. Otherwise, the
driver would use "phy-handle" in the DT as the reference to both the
external and the internal PCS/PMA PHY.
In other cases where the core is connected to a SFP cage, we could still
point phy-handle to the intenal PCS/PMA PHY, and let the driver connect
to the SFP module, if exist, via phylink.
Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Reviewed-by: Greentime Hu <greentime.hu@sifive.com>
Reviewed-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Document the new pcs-handle attribute to support connecting to an
external PHY. For Xilinx's AXI Ethernet, this is used when the core
operates in SGMII or 1000Base-X modes and links through the internal
PCS/PMA PHY.
Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Reviewed-by: Greentime Hu <greentime.hu@sifive.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
the struct member `phy_node` of struct axienet_local is not used by the
driver anymore after initialization. It might be a remnent of old code
and could be removed.
Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Reviewed-by: Greentime Hu <greentime.hu@sifive.com>
Reviewed-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to axienet_mdio_setup should not depend on whether "phy-node"
pressents on the DT. Besides, since `lp->phy_node` is used if PHY is in
SGMII or 100Base-X modes, move it into the if statement. And the next patch
will remove `lp->phy_node` from driver's private structure and do an
of_node_put on it right away after use since it is not used elsewhere.
Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Reviewed-by: Greentime Hu <greentime.hu@sifive.com>
Reviewed-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases, xdp tx_queue can get used before initialization.
1. interface up/down
2. ring buffer size change
When CPU cores are lower than maximum number of channels of sfc driver,
it creates new channels only for XDP.
When an interface is up or ring buffer size is changed, all channels
are initialized.
But xdp channels are always initialized later.
So, the below scenario is possible.
Packets are received to rx queue of normal channels and it is acted
XDP_TX and tx_queue of xdp channels get used.
But these tx_queues are not initialized yet.
If so, TX DMA or queue error occurs.
In order to avoid this problem.
1. initializes xdp tx_queues earlier than other rx_queue in
efx_start_channels().
2. checks whether tx_queue is initialized or not in efx_xdp_tx_buffers().
Splat looks like:
sfc 0000:08:00.1 enp8s0f1np1: TX queue 10 spurious TX completion id 250
sfc 0000:08:00.1 enp8s0f1np1: resetting (RECOVER_OR_ALL)
sfc 0000:08:00.1 enp8s0f1np1: MC command 0x80 inlen 100 failed rc=-22
(raw=22) arg=789
sfc 0000:08:00.1 enp8s0f1np1: has been disabled
Fixes: f28100cb9c96 ("sfc: fix lack of XDP TX queues - error XDP TX failed (-22)")
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While parsing user-provided actions, openvswitch module may dynamically
allocate memory and store pointers in the internal copy of the actions.
So this memory has to be freed while destroying the actions.
Currently there are only two such actions: ct() and set(). However,
there are many actions that can hold nested lists of actions and
ovs_nla_free_flow_actions() just jumps over them leaking the memory.
For example, removal of the flow with the following actions will lead
to a leak of the memory allocated by nf_ct_tmpl_alloc():
actions:clone(ct(commit),0)
Non-freed set() action may also leak the 'dst' structure for the
tunnel info including device references.
Under certain conditions with a high rate of flow rotation that may
cause significant memory leak problem (2MB per second in reporter's
case). The problem is also hard to mitigate, because the user doesn't
have direct control over the datapath flows generated by OVS.
Fix that by iterating over all the nested actions and freeing
everything that needs to be freed recursively.
New build time assertion should protect us from this problem if new
actions will be added in the future.
Unfortunately, openvswitch module doesn't use NLA_F_NESTED, so all
attributes has to be explicitly checked. sample() and clone() actions
are mixing extra attributes into the user-provided action list. That
prevents some code generalization too.
Fixes: 34ae932a4036 ("openvswitch: Make tunnel set action attach a metadata dst")
Link: https://mail.openvswitch.org/pipermail/ovs-dev/2022-March/392922.html
Reported-by: Stéphane Graber <stgraber@ubuntu.com>
Signed-off-by: Ilya Maximets <i.maximets@ovn.org>
Acked-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is often not a MAC address available in an EEPROM accessible by
Linux with Marvell devices. Instead the bootload has the MAC address
and directly programs it into the hardware. So don't consider an error
from of_get_mac_address() has fatal. However, the check was added for
the case where there is a MAC address in an the EEPROM, but the EEPROM
has not probed yet, and -EPROBE_DEFER is returned. In that case the
error should be returned. So make the check specific to this error
code.
Cc: Mauri Sandberg <maukka@ext.kapsi.fi>
Reported-by: Thomas Walther <walther-it@gmx.de>
Fixes: 42404d8f1c01 ("net: mv643xx_eth: process retval from of_get_mac_address")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220405000404.3374734-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
'OVS_CLONE_ATTR_EXEC' is an internal attribute that is used for
performance optimization inside the kernel. It's added by the kernel
while parsing user-provided actions and should not be sent during the
flow dump as it's not part of the uAPI.
The issue doesn't cause any significant problems to the ovs-vswitchd
process, because reported actions are not really used in the
application lifecycle and only supposed to be shown to a human via
ovs-dpctl flow dump. However, the action list is still incorrect
and causes the following error if the user wants to look at the
datapath flows:
# ovs-dpctl add-dp system@ovs-system
# ovs-dpctl add-flow "<flow match>" "clone(ct(commit),0)"
# ovs-dpctl dump-flows
<flow match>, packets:0, bytes:0, used:never,
actions:clone(bad length 4, expected -1 for: action0(01 00 00 00),
ct(commit),0)
With the fix:
# ovs-dpctl dump-flows
<flow match>, packets:0, bytes:0, used:never,
actions:clone(ct(commit),0)
Additionally fixed an incorrect attribute name in the comment.
Fixes: b233504033db ("openvswitch: kernel datapath clone action")
Signed-off-by: Ilya Maximets <i.maximets@ovn.org>
Acked-by: Aaron Conole <aconole@redhat.com>
Link: https://lore.kernel.org/r/20220404104150.2865736-1-i.maximets@ovn.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
1) Incorrect comparison in bitmask .reduce, from Jeremy Sowden.
2) Missing GFP_KERNEL_ACCOUNT for dynamically allocated objects,
from Vasily Averin.
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: nf_tables: memcg accounting for dynamically allocated objects
netfilter: bitwise: fix reduce comparisons
====================
Link: https://lore.kernel.org/r/20220405100923.7231-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently when XDP rings are created, each descriptor gets its DD bit
set, which turns out to be the wrong approach as it can lead to a
situation where more descriptors get cleaned than it was supposed to,
e.g. when AF_XDP busy poll is run with a large batch size. In this
situation, the driver would request for more buffers than it is able to
handle.
Fix this by not setting the DD bits in ice_xdp_alloc_setup_rings(). They
should be initialized to zero instead.
Fixes: 9610bd988df9 ("ice: optimize XDP_TX workloads")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Shwetha Nagaraju <shwetha.nagaraju@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
ICE_DOWN is dedicated for pf->state. Check for ICE_VSI_DOWN being set on
vsi->state in ice_xsk_wakeup().
Fixes: 2d4238f55697 ("ice: Add support for AF_XDP")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Shwetha Nagaraju <shwetha.nagaraju@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Unfortunately, the ice driver doesn't respect the RCU critical section that
XSK wakeup is surrounded with. To fix this, add synchronize_rcu() calls to
paths that destroy resources that might be in use.
This was addressed in other AF_XDP ZC enabled drivers, for reference see
for example commit b3873a5be757 ("net/i40e: Fix concurrency issues
between config flow and XSK")
Fixes: efc2214b6047 ("ice: Add support for XDP")
Fixes: 2d4238f55697 ("ice: Add support for AF_XDP")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Shwetha Nagaraju <shwetha.nagaraju@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
VRF devices are the loopbacks for VRFs, and a loopback can not be
assigned to a VRF. Accordingly, the condition in ip6_pkt_drop should
be '||' not '&&'.
Fixes: 1d3fd8a10bed ("vrf: Use orig netdev to count Ip6InNoRoutes and a fresh route lookup when sending dest unreach")
Reported-by: Pudak, Filip <Filip.Pudak@windriver.com>
Reported-by: Xiao, Jiguang <Jiguang.Xiao@windriver.com>
Signed-off-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20220404150908.2937-1-dsahern@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Tony Nguyen says:
====================
ice bug fixes
Alice Michael says:
There were a couple of bugs that have been found and
fixed by Anatolii in the ice driver. First he fixed
a bug on ring creation by setting the default value
for the teid. Anatolli also fixed a bug with deleting
queues in ice_vc_dis_qs_msg based on their enablement.
---
v2: Remove empty lines between tags
The following are changes since commit 458f5d92df4807e2a7c803ed928369129996bf96:
sfc: Do not free an empty page_ring
and are available in the git repository at:
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue 100GbE
====================
Link: https://lore.kernel.org/r/20220404183548.3422851-1-anthony.l.nguyen@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Disable check for queue being enabled in ice_vc_dis_qs_msg, because
there could be a case when queues were created, but were not enabled.
We still need to delete those queues.
Normal workflow for VF looks like:
Enable path:
VIRTCHNL_OP_ADD_ETH_ADDR (opcode 10)
VIRTCHNL_OP_CONFIG_VSI_QUEUES (opcode 6)
VIRTCHNL_OP_ENABLE_QUEUES (opcode 8)
Disable path:
VIRTCHNL_OP_DISABLE_QUEUES (opcode 9)
VIRTCHNL_OP_DEL_ETH_ADDR (opcode 11)
The issue appears only in stress conditions when VF is enabled and
disabled very fast.
Eventually there will be a case, when queues are created by
VIRTCHNL_OP_CONFIG_VSI_QUEUES, but are not enabled by
VIRTCHNL_OP_ENABLE_QUEUES.
In turn, these queues are not deleted by VIRTCHNL_OP_DISABLE_QUEUES,
because there is a check whether queues are enabled in
ice_vc_dis_qs_msg.
When we bring up the VF again, we will see the "Failed to set LAN Tx queue
context" error during VIRTCHNL_OP_CONFIG_VSI_QUEUES step. This
happens because old 16 queues were not deleted and VF requests to create
16 more, but ice_sched_get_free_qparent in ice_ena_vsi_txq would fail to
find a parent node for first newly requested queue (because all nodes
are allocated to 16 old queues).
Testing Hints:
Just enable and disable VF fast enough, so it would be disabled before
reaching VIRTCHNL_OP_ENABLE_QUEUES.
while true; do
ip link set dev ens785f0v0 up
sleep 0.065 # adjust delay value for you machine
ip link set dev ens785f0v0 down
done
Fixes: 77ca27c41705 ("ice: add support for virtchnl_queue_select.[tx|rx]_queues bitmap")
Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Alice Michael <alice.michael@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When VF is freshly created, but not brought up, ring->txq_teid
value is by default set to 0.
But 0 is a valid TEID. On some platforms the Root Node of
Tx scheduler has a TEID = 0. This can cause issues as shown below.
The proper way is to set ring->txq_teid to ICE_INVAL_TEID (0xFFFFFFFF).
Testing Hints:
echo 1 > /sys/class/net/ens785f0/device/sriov_numvfs
ip link set dev ens785f0v0 up
ip link set dev ens785f0v0 down
If we have freshly created VF and quickly turn it on and off, so there
would be no time to reach VIRTCHNL_OP_CONFIG_VSI_QUEUES stage, then
VIRTCHNL_OP_DISABLE_QUEUES stage will fail with error:
[ 639.531454] disable queue 89 failed 14
[ 639.532233] Failed to disable LAN Tx queues, error: ICE_ERR_AQ_ERROR
[ 639.533107] ice 0000:02:00.0: Failed to stop Tx ring 0 on VSI 5
The reason for the fail is that we are trying to send AQ command to
delete queue 89, which has never been created and receive an "invalid
argument" error from firmware.
As this queue has never been created, it's teid and ring->txq_teid
have default value 0.
ice_dis_vsi_txq has a check against non-existent queues:
node = ice_sched_find_node_by_teid(pi->root, q_teids[i]);
if (!node)
continue;
But on some platforms the Root Node of Tx scheduler has a teid = 0.
Hence, ice_sched_find_node_by_teid finds a node with teid = 0 (it is
pi->root), and we go further to submit an erroneous request to firmware.
Fixes: 37bb83901286 ("ice: Move common functions out of ice_main.c part 7/7")
Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Alice Michael <alice.michael@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This node pointer is returned by of_find_compatible_node() with
refcount incremented. Calling of_node_put() to aovid the refcount leak.
Fixes: d346c9e86d86 ("dpaa2-ptp: reuse ptp_qoriq driver")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220404125336.13427-1-linmq006@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
nft_*.c files whose NFT_EXPR_STATEFUL flag is set on need to
use __GFP_ACCOUNT flag for objects that are dynamically
allocated from the packet path.
Such objects are allocated inside nft_expr_ops->init() callbacks
executed in task context while processing netlink messages.
In addition, this patch adds accounting to nft_set_elem_expr_clone()
used for the same purposes.
Signed-off-by: Vasily Averin <vvs@openvz.org>
Acked-by: Roman Gushchin <roman.gushchin@linux.dev>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Singleton chunks (INIT, HEARTBEAT PMTU probes, and SHUTDOWN-
COMPLETE) are not counted in SCTP_GET_ASOC_STATS "sas_octrlchunks"
counter available to the assoc owner.
These are all control chunks so they should be counted as such.
Add counting of singleton chunks so they are properly accounted for.
Fixes: 196d67593439 ("sctp: Add support to per-association statistics via a new SCTP_GET_ASSOC_STATS call")
Signed-off-by: Jamie Bainbridge <jamie.bainbridge@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Link: https://lore.kernel.org/r/c9ba8785789880cf07923b8a5051e174442ea9ee.1649029663.git.jamie.bainbridge@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When the page_ring is not used page_ptr_mask is 0.
Do not dereference page_ring[0] in this case.
Fixes: 2768935a4660 ("sfc: reuse pages to avoid DMA mapping/unmapping costs")
Reported-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Smatch reports this issue
dwmac-loongson.c:208:19: warning: symbol
'loongson_dwmac_driver' was not declared.
Should it be static?
loongson_dwmac_driver is only used in dwmac-loongson.c.
File scope variables used only in one file should
be static. Change loongson_dwmac_driver's
storage-class-specifier from global to static.
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan says:
====================
bnxt_en: XDP redirect fixes
This series includes 3 fixes related to the XDP redirect code path in
the driver. The first one adds locking when the number of TX XDP rings
is less than the number of CPUs. The second one adjusts the maximum MTU
that can support XDP with enough tail room in the buffer. The 3rd one
fixes a race condition between TX ring shutdown and the XDP redirect path.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add checks in the XDP redirect callback to prevent XDP from running when
the TX ring is undergoing shutdown.
Also remove redundant checks in the XDP redirect callback to validate the
txr and the flag that indicates the ring supports XDP. The modulo
arithmetic on 'tx_nr_rings_xdp' already guarantees the derived TX
ring is an XDP ring. txr is also guaranteed to be valid after checking
BNXT_STATE_OPEN and within RCU grace period.
Fixes: f18c2b77b2e4 ("bnxt_en: optimized XDP_REDIRECT support")
Reviewed-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Insufficient space was being reserved in the page used for packet
reception, so the interface MTU could be set too large to still have
room for the contents of the packet when doing XDP redirect. This
resulted in the following message when redirecting a packet between
3520 and 3822 bytes with an MTU of 3822:
[311815.561880] XDP_WARN: xdp_update_frame_from_buff(line:200): Driver BUG: missing reserved tailroom
Fixes: f18c2b77b2e4 ("bnxt_en: optimized XDP_REDIRECT support")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there are more CPUs than the number of TX XDP rings, multiple XDP
redirects can select the same TX ring based on the CPU on which
XDP redirect is called. Add locking when needed and use static
key to decide whether to take the lock.
Fixes: f18c2b77b2e4 ("bnxt_en: optimized XDP_REDIRECT support")
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To fix a coverity complain, commit d5ac07dfbd2b
("qed: Initialize debug string array") removed "sw-platform"
(one of the common global parameters) from the dump as this
was used in the dump with an uninitialized string, however
it did not reduce the number of common global parameters
which caused the incorrect (unable to parse) register dump
this patch fixes it with reducing NUM_COMMON_GLOBAL_PARAMS
bye one.
Cc: stable@vger.kernel.org
Cc: Tim Gardner <tim.gardner@canonical.com>
Cc: "David S. Miller" <davem@davemloft.net>
Fixes: d5ac07dfbd2b ("qed: Initialize debug string array")
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Manish Chopra <manishc@marvell.com>
Reviewed-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Horatiu Vultur says:
====================
net: phy: micrel: Remove latencies support lan8814
Remove the latencies support both from the PHY driver and from the DT.
The IP already has some default latencies values which can be used to get
decent results. It has the following values(defined in ns):
rx-1000mbit: 429
tx-1000mbit: 201
rx-100mbit: 2346
tx-100mbit: 705
v0->v1:
- fix the split of the patches, there was a compiling error between patch 2 and
patch 3.
---
But to get better results the following values needs to be set:
rx-1000mbit: 459
tx-1000mbit: 171
rx-100mbit: 1706
tx-100mbit: 1345
We are proposing to use ethtool to set these latencies, the RFC can be found
here[1]
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When the PHY and the MAC are capable of doing timestamping, the PHY has
priority. Therefore the DT option lan8814,ignore-ts was added such that
the PHY will not expose a PHC so then the timestamping was done in the
MAC. This is not the correct approach of doing it, therefore remove
this.
Fixes: ece19502834d84 ("net: phy: micrel: 1588 support for LAN8814 phy")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on the discussions here[1], the PHY driver is the wrong place
to set the latencies, therefore remove them.
[1] https://lkml.org/lkml/2022/3/4/325
Fixes: ece19502834d84 ("net: phy: micrel: 1588 support for LAN8814 phy")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Revert latency support from binding.
Based on the discussion[1], the DT is the wrong place to have the
lantecies for the PHY.
[1] https://lkml.org/lkml/2022/3/4/325
Fixes: 2358dd3fd325fc ("dt-bindings: net: micrel: Configure latency values and timestamping check for LAN8814 phy")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I made a stupid typo when adding the nexthop route warning selftest and
added both $IP and ip after it (double ip) on the cleanup path. The
error doesn't show up when running the test, but obviously it doesn't
cleanup properly after it.
Fixes: 392baa339c6a ("selftests: net: add delete nexthop route warning test")
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 9cbadf094d9d ("net: stmmac: support max-speed device tree
property"), when DT platforms don't set "max-speed", max_speed is set to
-1; for non-DT platforms, it stays the default 0.
Prior to commit eeef2f6b9f6e ("net: stmmac: Start adding phylink support"),
the check for a valid max_speed setting was to check if it was greater
than zero. This commit got it right, but subsequent patches just checked
for non-zero, which is incorrect for DT platforms.
In commit 92c3807b9ac3 ("net: stmmac: convert to phylink_get_linkmodes()")
the conversion switched completely to checking for non-zero value as a
valid value, which caused 1000base-T to stop getting advertised by
default.
Instead of trying to fix all the checks, simply leave max_speed alone if
DT property parsing fails.
Fixes: 9cbadf094d9d ("net: stmmac: support max-speed device tree property")
Fixes: 92c3807b9ac3 ("net: stmmac: convert to phylink_get_linkmodes()")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220331184832.16316-1-wens@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
32b builds with CONFIG_PHYS_ADDR_T_64BIT=y, such as i386 PAE,
raise a linker error due to a 64b division:
ld: drivers/net/ethernet/fungible/funcore/fun_dev.o: in function
`fun_dev_enable':
(.text+0xe1a): undefined reference to `__udivdi3'
The divisor in the offendinng expression is a power of 2. Change it to
use an explicit right shift.
Fixes: e1ffcc66818f ("net/fungible: Add service module for Fungible drivers")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Dimitris Michailidis <dmichail@fungible.com>
Link: https://lore.kernel.org/r/20220401232411.313881-1-dmichail@fungible.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nikolay Aleksandrov says:
====================
net: ipv4: fix nexthop route delete warning
The first patch fixes a warning that can be triggered by deleting a
nexthop route and specifying a device (more info in its commit msg).
And the second patch adds a selftest for that case.
Chose this way to fix it because we should match when deleting without
nh spec and should fail when deleting a nexthop route with old-style nh
spec because nexthop objects are managed separately, e.g.:
$ ip r show 1.2.3.4/32
1.2.3.4 nhid 12 via 192.168.11.2 dev dummy0
$ ip r del 1.2.3.4/32
$ ip r del 1.2.3.4/32 nhid 12
<both should work>
$ ip r del 1.2.3.4/32 dev dummy0
<should fail with ESRCH>
v2: addded more to patch 01's commit message
adjusted the test comment in patch 02
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test which causes a WARNING on kernels which treat a
nexthop route like a normal route when comparing for deletion and a
device is specified. That is, a route is found but we hit a warning while
matching it. The warning is from fib_info_nh() in include/net/nexthop.h
because we run it on a fib_info with nexthop object. The call chain is:
inet_rtm_delroute -> fib_table_delete -> fib_nh_match (called with a
nexthop fib_info and also with fc_oif set thus calling fib_info_nh on
the fib_info and triggering the warning).
Repro steps:
$ ip nexthop add id 12 via 172.16.1.3 dev veth1
$ ip route add 172.16.101.1/32 nhid 12
$ ip route delete 172.16.101.1/32 dev veth1
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
KS8851_MLL selects MICREL_PHY, which depends on PTP_1588_CLOCK_OPTIONAL,
so make KS8851_MLL also depend on PTP_1588_CLOCK_OPTIONAL since
'select' does not follow any dependency chains.
Fixes kconfig warning and build errors:
WARNING: unmet direct dependencies detected for MICREL_PHY
Depends on [m]: NETDEVICES [=y] && PHYLIB [=y] && PTP_1588_CLOCK_OPTIONAL [=m]
Selected by [y]:
- KS8851_MLL [=y] && NETDEVICES [=y] && ETHERNET [=y] && NET_VENDOR_MICREL [=y] && HAS_IOMEM [=y]
ld: drivers/net/phy/micrel.o: in function `lan8814_ts_info':
micrel.c:(.text+0xb35): undefined reference to `ptp_clock_index'
ld: drivers/net/phy/micrel.o: in function `lan8814_probe':
micrel.c:(.text+0x2586): undefined reference to `ptp_clock_register'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Johnston says:
====================
MCTP fixes
The following are fixes for the mctp core and mctp-i2c driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously the skb was allocated with headroom MCTP_HEADER_MAXLEN,
but that isn't sufficient if we are using devs that are not MCTP
specific.
This also adds a check that the smctp_halen provided to sendmsg for
extended addressing is the correct size for the netdev.
Fixes: 833ef3b91de6 ("mctp: Populate socket implementation")
Reported-by: Matthew Rinaldi <mjrinal@g.clemson.edu>
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
header_ops.create should return the length of the header,
instead mctp_i2c_head_create() returned 0.
This didn't cause any problem because the MCTP stack accepted
0 as success.
Fixes: f5b8abf9fc3d ("mctp i2c: MCTP I2C binding driver")
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
