There's a use case that playback stream of a loopback cable works on
RW_INTERLEAVED mode while capture stream works on MMAP_INTERLEAVED mode:
aplay -Dhw:Loopback,0,0 S32_48K_2ch.wav;
arecord -Dplughw:Loopback,1,0 -fS32_LE -r16000 -c2 cap.wav;
The plug plugin handles only slave PCM support MMAP mode. Not only plug
plugin but also other plugins like direct plugins(dmix/dsnoop/dshare)
work on MMAP access mode. In this case capture stream is the slave
PCM works on MMAP_INTERLEAVED mode. However loopback_check_format()
rejects this access setting and return:
arecord: pcm_read:2240: read error: Input/output error
To fix it a function called is_access_interleaved() is introduced to
get if access is interleaved mode. If both access of capture stream and
playback stream is interleaved mode loopback_check_format() will allow
this kind of access setting.
Fixes: 462494565c27 ("ALSA: aloop: Add support for the non-interleaved access mode")
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Link: https://lore.kernel.org/r/20240111025219.2678764-1-chancel.liu@nxp.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When OMTP headset plugin the headset jack of CX8070 and SN6160 sound cards,
the headset type detection circuit will recognize the headset type as CTIA.
At this point, plugout and plugin the headset will get the correct headset
type as OMTP.
The reason for the failure of headset type recognition is that the sound
card creation will enable the VREF voltage of the headset mic, which
interferes with the headset type automatic detection circuit. Plugout and
plugin the headset will restart the headset detection and get the correct
headset type.
The patch is disable the VREF voltage when the headset is not present, and
will enable the VREF voltage when the headset is present.
Signed-off-by: bo liu <bo.liu@senarytech.com>
Link: https://lore.kernel.org/r/20240108110235.3867-1-bo.liu@senarytech.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a relatively quiet release, there's a lot of driver specific
changes and the usual high level of activity in the SOF core but the
one big core change was Mormioto-san's work to support more N:M
CPU:CODEC mapping cases. Highlights include:
- Enhanced support for N:M CPU:CODEC mappings in the core and in
audio-graph-card2.
- Support for falling back to older SOF IPC versions where firmware for
new versions is not available.
- Support for notification of control changes generated by SOF firmware
with IPC4.
- Device tree support for describing parts of the card which can be
active over suspend (for very low power playback or wake word use
cases).
- ACPI parsing support for the ES83xx driver, reducing the number of
quirks neede for x86 systems.
- Support for more AMD and Intel systems, NXP i.MX8m MICFIL, Qualcomm
SM8250, SM8550, SM8650 and X1E80100.
- Removal of Freescale MPC8610 support, the SoC is no longer supported
by Linux.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmWbJ5EACgkQJNaLcl1U
h9CZTwf/c8CPwoKABZear8jiQpZLUhFLuGQwSShPYVZ7XPzzTMp9BwVmd40DCnUi
NeSc22t2UgT0H06nx3QK8sKOhrpQoBQVrIajf2AaxD44TJbsOYGGe4pMh1sXKAMF
c0ybp8uRgsjiv2Y++SBXZLexGC11/b8eTFLV1nTK/i2nygGjbfWSJ9s4PpB9V6cA
nZrQ/p+x/ZwaBejFUnvE06M7GHtCD6lxrB9Q1EmWA4RxcW7RNUtIN5gr16HlaMiC
3gix4mg40llhBFF9s4eBjRBNKL2paiejPZwcYkAC8w+SkZ/roXaeN55g0avmDWyW
AN9o096vaEVWKhZ/jdTHmFVf2PV2Iw==
=rbT5
-----END PGP SIGNATURE-----
Merge tag 'asoc-v6.8' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v6.8
This is a relatively quiet release, there's a lot of driver specific
changes and the usual high level of activity in the SOF core but the
one big core change was Mormioto-san's work to support more N:M
CPU:CODEC mapping cases. Highlights include:
- Enhanced support for N:M CPU:CODEC mappings in the core and in
audio-graph-card2.
- Support for falling back to older SOF IPC versions where firmware for
new versions is not available.
- Support for notification of control changes generated by SOF firmware
with IPC4.
- Device tree support for describing parts of the card which can be
active over suspend (for very low power playback or wake word use
cases).
- ACPI parsing support for the ES83xx driver, reducing the number of
quirks neede for x86 systems.
- Support for more AMD and Intel systems, NXP i.MX8m MICFIL, Qualcomm
SM8250, SM8550, SM8650 and X1E80100.
- Removal of Freescale MPC8610 support, the SoC is no longer supported
by Linux.
I recently got a LibreTech Sapphire board for my CI and while
integrating it found and fixed some issues, including crashes for the
enum validation. There's also a couple of patches adding quirks for
another x86 laptop from Hans and an error handling fix for the Freescale
rpmsg driver.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmWVw4MACgkQJNaLcl1U
h9DUtwf+KWJ3vDz+6llOo2sok0teL3fkPBhgPzSsSo/pTX8SLNyFrLPf1HJSLdd9
Vzc8LUU+05TyklP3TemOh42J6RoQlVxuKq0Qnc3unHhrUpIDKUmC4TWraQkI3hUo
iy8/DmS3isNrAGfXflrKbx12HCFCBxNjpuskEC+FyXhxORopE5XyAKtVLxO/U1/M
PfF0H0VRmtc+dY0eG5VXsVJk/VulCRsg/5DauLtWsfvnZ6rEt4H2ffQJ41fedOlX
fSlUbOEju8P4MIklkXV/GmYhsrr8Yw+G3W83DDcoJ8OuBi41MCkIpIwtoJQJHDcL
4otewgc+Yd6KqxqYMgpBqYz1mlghZw==
=3Pvo
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v6.7-rc8' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v6.7
I recently got a LibreTech Sapphire board for my CI and while
integrating it found and fixed some issues, including crashes for the
enum validation. There's also a couple of patches adding quirks for
another x86 laptop from Hans and an error handling fix for the Freescale
rpmsg driver.
When a control changes value the return value from _put() should be 1 so
we get events generated to userspace notifying applications of the change.
While the I2S mux gets this right the S/PDIF mux does not, fix the return
value.
Fixes: c8609f3870f7 ("ASoC: meson: add g12a tohdmitx control")
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20240103-meson-enum-val-v1-4-424af7a8fb91@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
When a control changes value the return value from _put() should be 1 so
we get events generated to userspace notifying applications of the change.
We are checking if there has been a change and exiting early if not but we
are not providing the correct return value in the latter case, fix this.
Fixes: af2618a2eee8 ("ASoC: meson: g12a: add internal DAC glue driver")
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20240103-meson-enum-val-v1-3-424af7a8fb91@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
When writing to an enum we need to verify that the value written is valid
for the enumeration, the helper function snd_soc_item_enum_to_val() doesn't
do it since it needs to return an unsigned (and in any case we'd need to
check the return value).
Fixes: c8609f3870f7 ("ASoC: meson: add g12a tohdmitx control")
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20240103-meson-enum-val-v1-2-424af7a8fb91@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
When writing to an enum we need to verify that the value written is valid
for the enumeration, the helper function snd_soc_item_enum_to_val() doesn't
do it since it needs to return an unsigned (and in any case we'd need to
check the return value).
Fixes: af2618a2eee8 ("ASoC: meson: g12a: add internal DAC glue driver")
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20240103-meson-enum-val-v1-1-424af7a8fb91@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The current code flow is:
1. snd_hdac_device_register()
2. set parameters needed by the hdac driver
3. request_codec_module()
the hdac driver is probed at this point
During boot the codec drivers are not loaded when the hdac device is
registered, it is going to be probed later when loading the codec module,
which point the parameters are set.
On module remove/insert
rmmod snd_sof_pci_intel_tgl
modprobe snd_sof_pci_intel_tgl
The codec module remains loaded and the driver will be probed when the
hdac device is created right away, before the parameters for the driver
has been configured:
1. snd_hdac_device_register()
the hdac driver is probed at this point
2. set parameters needed by the hdac driver
3. request_codec_module()
will be a NOP as the module is already loaded
Move the snd_hdac_device_register() later, to be done right before
requesting the codec module to make sure that the parameters are all set
before the device is created:
1. set parameters needed by the hdac driver
2. snd_hdac_device_register()
3. request_codec_module()
This way at the hdac driver probe all parameters will be set in all cases.
Link: https://github.com/thesofproject/linux/issues/4731
Fixes: a0575b4add21 ("ASoC: hdac_hda: Conditionally register dais for HDMI and Analog")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20231207095425.19597-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/ZYvUIxtrqBQZbNlC@shine.dominikbrodowski.net
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218304
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When CONFIG_SPI is disabled, the driver produces unused-variable warning:
sound/pci/hda/cs35l41_hda_property.c: In function 'generic_dsd_config':
sound/pci/hda/cs35l41_hda_property.c:181:28: error: unused variable 'spi' [-Werror=unused-variable]
181 | struct spi_device *spi;
| ^~~
sound/pci/hda/cs35l41_hda_property.c:180:27: error: unused variable 'cs_gpiod' [-Werror=unused-variable]
180 | struct gpio_desc *cs_gpiod;
| ^~~~~~~~
Avoid these by turning the preprocessor contionals into equivalent C code,
which also helps readability.
Fixes: 916d051730ae ("ALSA: hda: cs35l41: Only add SPI CS GPIO if SPI is enabled in kernel")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240103102606.3742476-1-arnd@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ac97_bus_type structure is no longer declared in this file:
sound/ac97/bus.c: In function 'ac97_codec_add':
sound/ac97/bus.c:112:27: error: 'ac97_bus_type' undeclared (first use in this function); did you mean 'bus_type'?
112 | codec->dev.bus = &ac97_bus_type;
| ^~~~~~~~~~~~~
| bus_type
sound/ac97/bus.c:112:27: note: each undeclared identifier is reported only once for each function it appears in
sound/ac97/bus.c: In function 'snd_ac97_codec_driver_register':
sound/ac97/bus.c:191:28: error: 'ac97_bus_type' undeclared (first use in this function); did you mean 'ac97_bus_reset'?
191 | drv->driver.bus = &ac97_bus_type;
Include the header that contains the declaration and make sure the definition
is const but not static.
Fixes: 66e82d219924 ("ALSA: mark all struct bus_type as const")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240103102544.3715055-1-arnd@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This adds overrides for a series of notebooks using a common config
taken from HP's proprietary Windows driver.
This has been tested on a HP 15-ey0xxxx device (subsystem 103C8A31)
together with another Realtek quirk and the calibration files from the
proprietary driver.
Signed-off-by: Lorenz Brun <lorenz@brun.one>
Cc: <stable@vger.kernel.org> # v6.7
Link: https://lore.kernel.org/r/20240102214821.3394810-1-lorenz@brun.one
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is a HP ZBook which using ALC236 codec and need the
ALC236_FIXUP_HP_MUTE_LED_MICMUTE_VREF quirk to make mute LED
and micmute LED work.
[ confirmed that the new entries are for new models that have no
proper name, so the strings are left as "HP" which will be updated
eventually later -- tiwai ]
Signed-off-by: Andy Chi <andy.chi@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20240102024916.19093-1-andy.chi@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add driver properties on 4 models of this laptop serie since they don't
have _DSD in the ACPI table
Signed-off-by: Dorian Cruveiller <doriancruveiller@gmail.com>
Cc: <stable@vger.kernel.org> # v6.7
Link: https://lore.kernel.org/r/20231230114312.22118-1-doriancruveiller@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HP Pavilion 14 ec1xxx series uses the HP mainboard 8A0F with the
ALC287 codec.
The mute led can be enabled using the already existing
ALC287_FIXUP_HP_GPIO_LED quirk.
Tested on an HP Pavilion ec1003AU
Signed-off-by: Aabish Malik <aabishmalik3337@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231229170352.742261-3-aabishmalik3337@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now that the driver core can properly handle constant struct bus_type,
move all of the sound subsystem struct bus_type structures as const,
placing them into read-only memory which can not be modified at runtime.
Note, this fixes a duplicate definition of ac97_bus_type, which somehow
was declared extern in a .h file, and then static as a prototype in a .c
file, and then properly later on in the same .c file. Amazing that no
compiler warning ever showed up for this.
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Dawei Li <set_pte_at@outlook.com>
Cc: Yu Liao <liaoyu15@huawei.com>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: linux-sound@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/2023121945-immersion-budget-d0aa@gregkh
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AUD_PAD_TOP widget's correct register is AFE_AUD_PAD_TOP , and not zero.
Having a zero as register, it would mean that the `snd_soc_dapm_new_widgets`
would try to read the register at offset zero when trying to get the power
status of this widget, which is incorrect.
Fixes: b65c466220b3 ("ASoC: mediatek: mt8186: support adda in platform driver")
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Link: https://lore.kernel.org/r/20231229114342.195867-1-eugen.hristev@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When the Direct button on the Solo Gen 4 is held for 3 seconds, the
PCM 1 and 2 inputs are toggled between DSP Outputs 1 and 2, and Mixer
Outputs E and F. This patch adds the corresponding ALSA control.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/8c67c6131c459588ac4edab11e1fbc40a8297328.1703612638.git.g@b4.vu
The Scarlett 4i4 Gen 4 adds a R/O headphone volume control in addition
to a R/O master volume control (which is already supported).
Mark the new scarlett2_notify_volume() function with __always_unused
until it gets used when the Gen 4 notification callback function arrays
are added.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/bd4a76da157f8cc3fbfa02eba96d02bdb86817c5.1703612638.git.g@b4.vu
Early firmware for the Scarlett Gen 4 devices has sufficient
differences that it is better to enforce a minimum firmware version
than to try and work around those differences. Add a minimum firmware
version field to the device info struct, and display a message if the
firmware version is too old. Only create the Firmware Version and MSD
(optional) controls in this case.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/5455a7e54bda81556066abd7f761b10e9c5f8a16.1703612638.git.g@b4.vu
The DSP mux channels are of type SCARLETT2_PORT_TYPE_MIX so the
ALSA controls would refer to them "Mix X" and "Mixer Input X". This
patch fixes them to be called "DSP X" and "DSP Input X".
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/2d91d0a74d5c7f6179e950bed2c80a4498d16649.1703612638.git.g@b4.vu
The DSP mux channels in the Scarlett 4th Gen appear as
SCARLETT2_PORT_TYPE_MIX ports but do not have corresponding mixer
controls. Add a dsp_count option to the device info struct to exclude
those DSP channels from the num_mix_in/num_mix_out counts.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/b78bdb1a7624d55783f5bf0e1ffbfa47a9e9a800.1703612638.git.g@b4.vu
The mixes used by Direct Monitor feature on the Scarlett 4th Gen Solo
and 2i2 interfaces are configurable. This patch adds ALSA controls for
the gains which are copied to the mixer when Direct Monitor is
enabled.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/96282a805b45f04560e5923d170745363906b7f3.1703612638.git.g@b4.vu
When the Direct Monitor feature on the Scarlett 4th Gen Solo and 2i2
interfaces is used, the Mix A and B gains are updated by the
interface. This patch calls snd_ctl_notify() for the ALSA mix controls
when a Direct Monitor notification is received.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/713d032e343e0547212368919bef17d6fa1c9d29.1703612638.git.g@b4.vu
The Scarlett 4th Gen small interfaces have a software-controllable
mixer like the large 2nd and 3rd Gen interfaces do. Pressing the
"Direct" button on the interface updates the mixer controls, which
this driver hasn't needed to deal with previously.
This commit stores the ALSA mixer controls, and adds a mix_updated
flag so that the controls can be updated when a notification is
received.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/3ba27c60230511b80b0fa75727551ea70f17d829.1703612638.git.g@b4.vu
Add a control to retrieve the power status from the interface
(bus-powered, external-powered, or insufficient power).
Mark the new scarlett2_notify_power_status() function with
__always_unused until it gets used when the Gen 4 notification
callback function arrays are added.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/d9806bc41adc45b1c19749562fec7765ba24351d.1703612638.git.g@b4.vu
When phantom power is enabled or disabled, the autogain control cannot
be enabled until the interface has signalled that the change is
complete and the input is unmuted. Update those controls to be
read-only during this time.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/f49f7bf9358e1f20713d95d407d8d6a436859877.1703612638.git.g@b4.vu
While the autogain function is running, the other input controls
(select, link, gain, safe, level, air, and phantom) can't be modified.
Update those controls to be read-only during this time.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/ad13bacae77860de8c2d7c89f6ec2a1ee104e65f.1703612638.git.g@b4.vu
Some devices in the Scarlett Gen 4 series have support for
software-controllable input gain. Along with this comes a channel
select option, an auto-gain feature, "safe" mode, and linking two
channels into a stereo pair.
Mark the new scarlett2_notify_input_*() functions with __always_unused
until they get used when the Gen 4 notification callback function
arrays are added.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/fc39e80bb39863dd1579d342097203942b4f3034.1703612638.git.g@b4.vu
Gen 2/3 interfaces would only use 0/1 values for input level and
phantom power switch controls. Gen 4 interfaces use the second bit to
indicate that the state should be changed (or is changing), and the
input is to be muted (or is muted) while that happens.
Add a "mute" flag to config items to enable this behaviour for the
level/phantom controls.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/f603cd16079c97fad910087e0302828a289d1c15.1703612638.git.g@b4.vu
Writing Scarlett Gen 4 parameters differs from Gen 2 and Gen 3:
- the values are written into a shared write location
- the values are only byte-sized
- the read locations now extend beyond 0xFF
- a separate NVRAM save step is no longer required
This patch implements that alternate write style, triggered by setting
the config item size field to zero.
The write address is specified through a new config set field
gen4_write_addr.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/1624e6d8a0c629c3bdfe53825b16e8b589724fc4.1703612638.git.g@b4.vu
The Focusrite Scarlett Gen 4 Solo has Air and Phantom Power controls
on analogue input #2 (the Gen 3 Solo had these controls on analogue
input #1). Add air_input_first and phantom_first device info options
to cater for this.
These options are similar to the level_input_first option that was
added for the Gen 3 Solo, but these new options do not require
adjusting the index of the control.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/19511f18895b8c094985a4a5691fbc1dc028c108.1703612638.git.g@b4.vu
