The SAR2130P platform has the same TCSR Clock Controller as the SM8550,
except for the lack of the UFS clocks. Extend the SM8550 TCSRCC driver
to support SAR2130P.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241027-sar2130p-clocks-v5-9-ecad2a1432ba@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add driver for the Global Clock Controller as present on the Qualcomm
SAR2130P platform. This is based on the msm-5.10 tree, tag
KERNEL.PLATFORM.1.0.r4-00400-NEO.0.
Co-developed-by: Kalpak Kawadkar <quic_kkawadka@quicinc.com>
Signed-off-by: Kalpak Kawadkar <quic_kkawadka@quicinc.com>
Acked-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241027-sar2130p-clocks-v5-8-ecad2a1432ba@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Define clocks as supported by the RPMh on the SAR2130P platform. The
msm-5.10 kernel declares just the CXO clock, the RF_CLK1 clock was added
following recommendation from Taniya Das.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Taniya Das <quic_tdas@quicinc.com>
Link: https://lore.kernel.org/r/20241027-sar2130p-clocks-v5-7-ecad2a1432ba@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Generally SDCC clocks use clk_rcg2_floor_ops, however on SAR2130P
platform it's recommended to use rcg2_shared_ops for all Root Clock
Generators to park them instead of disabling. Implement a mix of those,
clk_rcg2_shared_floor_ops.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241027-sar2130p-clocks-v5-6-ecad2a1432ba@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Like all other non-ancient Qualcomm clock drivers, QCOM_GDSC is
required, as the GCC driver defines and instantiates a bunch of GDSCs.
Add the missing dependency.
Reported-by: Kamil Gołda <kamil.golda@protonmail.com>
Signed-off-by: Konrad Dybcio <quic_kdybcio@quicinc.com>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Link: https://lore.kernel.org/r/20241003-topic-6125kconfig-v1-1-f5e1efbff07c@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The lucid 5lpe PLL enable check only checks for an impossible negative
return value and does not actually return as intended in case the PLL is
already enabled (e.g. has been left enabled by boot firmware).
Fixes: f4c7e27aa4 ("clk: qcom: clk-alpha-pll: Add support for Lucid 5LPE PLL")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20241022080521.359-3-johan+linaro@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The boot firmware may have left the display enabled and its PLL running,
which currently generates a warning on boot (e.g. on x1e80100):
disp_cc_pll0 PLL is already enabled
Drop the bogus warning and fix up the PLL enabled error handling
(trion_pll_is_enabled() only returns 0 or 1).
Fixes: d1b121d62b ("clk: qcom: Add LUCID_EVO PLL type for SDX65")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20241022080521.359-2-johan+linaro@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
This driver is compatible with both sm8550 and sm8650, fix the Kconfig
entry to reflect that.
Fixes: da1f361c88 ("clk: qcom: videocc-sm8550: Add SM8650 video clock controller")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20241005144047.2226-1-jonathan@marek.ca
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Drivers and core code does not modify the file-scope static 'struct
qcom_icc_hws_data', so it can be made const for code safety and
readability.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240905150235.276345-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add support to the SM8475 camera clock controller by extending the
SM8450 camera clock controller, which is almost identical but has some
minor differences.
Signed-off-by: Danila Tikhonov <danila@jiaxyga.com>
Link: https://lore.kernel.org/r/20240818204348.197788-11-danila@jiaxyga.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add support to the SM8475 video clock controller by extending the
SM8450 video clock controller, which is almost identical but has some
minor differences.
Signed-off-by: Danila Tikhonov <danila@jiaxyga.com>
Link: https://lore.kernel.org/r/20240818204348.197788-9-danila@jiaxyga.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add support to the SM8475 graphics clock controller by extending the
SM8450 graphics clock controller, which is almost identical but has
some minor differences.
Signed-off-by: Danila Tikhonov <danila@jiaxyga.com>
Link: https://lore.kernel.org/r/20240818204348.197788-7-danila@jiaxyga.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add support to the SM8475 display clock controller by extending the
SM8450 display clock controller, which is almost identical but has
some minor differences.
Signed-off-by: Danila Tikhonov <danila@jiaxyga.com>
Link: https://lore.kernel.org/r/20240818204348.197788-5-danila@jiaxyga.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add support to the SM8475 global clock controller by extending the
SM8450 global clock controller, which is almost identical but has some
minor differences.
Signed-off-by: Danila Tikhonov <danila@jiaxyga.com>
Link: https://lore.kernel.org/r/20240818204348.197788-3-danila@jiaxyga.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
This concludes a long journey towards replacing the old
board files with devictree description on the Cirrus Logic
EP93xx platform.
Nikita Shubin has been working on this for a long time,
for details see the last post on
https://lore.kernel.org/lkml/20240909-ep93xx-v12-0-e86ab2423d4b@maquefel.me/
-----BEGIN PGP SIGNATURE-----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=Y3Cd
-----END PGP SIGNATURE-----
Merge tag 'soc-ep93xx-dt-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC update from Arnd Bergmann:
"Convert ep93xx to devicetree
This concludes a long journey towards replacing the old board files
with devictree description on the Cirrus Logic EP93xx platform.
Nikita Shubin has been working on this for a long time, for details
see the last post on
https://lore.kernel.org/lkml/20240909-ep93xx-v12-0-e86ab2423d4b@maquefel.me/"
* tag 'soc-ep93xx-dt-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (47 commits)
dt-bindings: gpio: ep9301: Add missing "#interrupt-cells" to examples
MAINTAINERS: Update EP93XX ARM ARCHITECTURE maintainer
soc: ep93xx: drop reference to removed EP93XX_SOC_COMMON config
net: cirrus: use u8 for addr to calm down sparse
dmaengine: cirrus: use snprintf() to calm down gcc 13.3.0
dmaengine: ep93xx: Fix a NULL vs IS_ERR() check in probe()
pinctrl: ep93xx: Fix raster pins typo
spi: ep93xx: update kerneldoc comments for ep93xx_spi
clk: ep93xx: Fix off by one in ep93xx_div_recalc_rate()
clk: ep93xx: add module license
dmaengine: cirrus: remove platform code
ASoC: cirrus: edb93xx: Delete driver
ARM: ep93xx: soc: drop defines
ARM: ep93xx: delete all boardfiles
ata: pata_ep93xx: remove legacy pinctrl use
pwm: ep93xx: drop legacy pinctrl
ARM: ep93xx: DT for the Cirrus ep93xx SoC platforms
ARM: dts: ep93xx: Add EDB9302 DT
ARM: dts: ep93xx: add ts7250 board
ARM: dts: add Cirrus EP93XX SoC .dtsi
...
support for the newly ratified DT property 'assigned-clock-rates-u64'. I'm much
more excited about the support for loading DT overlays from KUnit tests so that
we can test how the clk framework parses DT nodes during clk registration. The
clk framework has some places that are highly DeviceTree dependent so this
charts the path to extend the KUnit tests to cover even more framework code in
the future. I've got some more tests on the list that use the DT overlay
support, but they uncovered issues with clk unregistration that I'm still
working on fixing.
Outside the core, the clk driver update pile is dominated by Qualcomm and
Renesas SoCs, making it fairly usual. Looking closer, there are fixes for
things all over the place, like adding missing clk frequencies or moving
defines for the number of clks out of DT binding headers into the drivers.
There are even conversions of DT bindings to YAML and migration away from
strings to describe clk topology. Overall it doesn't look unusual so I expect
the new drivers to be where we'll have fixes in the coming weeks.
Core:
- KUnit tests for clk registration and fixed rate basic clk type
- A couple more devm helpers, one consumer and one provider
- Support for assigned-clock-rates-u64
New Drivers:
- Camera, display and GPU clocks on Qualcomm SM4450
- Camera clocks on Qualcomm SM8150
- Rockchip rk3576 clks
- Microchip SAM9X7 clks
- Renesas RZ/V2H(P) (R9A09G057) clks
Updates:
- Mark a bunch of struct freq_tbl const to reduce .data usage
- Add Qualcomm MSM8226 A7PLL and Regera PLL support
- Fix the Qualcomm Lucid 5LPE PLL configuration sequence to not reuse
Trion, as they do differ
- A number of fixes to the Qualcomm SM8550 display clock driver
- Fold Qualcomm SM8650 display clock driver into SM8550 one
- Add missing clocks and GDSCs needed for audio on Qualcomm MSM8998
- Add missing USB MP resets, GPLL9, and QUPv3 DFS to Qualcomm SC8180X
- Fix sdcc clk frequency tables on Qualcomm SC8180X
- Drop the Qualcomm SM8150 gcc_cpuss_ahb_clk_src
- Mark Qualcomm PCIe GDSCs as RET_ON on sm8250 and sm8540 to avoid them
turning off during suspend
- Use the HW_CTRL mechanism on Qualcomm SM8550 video clock controller
GDSCs
- Get rid of CLK_NR_CLKS defines in Rockchip DT binding headers
- Some fixes for Rockchip rk3228 and rk3588
- Exynos850: Add clock for Thermal Management Unit
- Exynos7885: Fix duplicated ID in the header, add missing TOP PLLs and
add clocks for USB block in the FSYS clock controller
- ExynosAutov9: Add DPUM clock controller
- ExynosAutov920: Add new (first) clock controllers: TOP and PERIC0
(and a bit more complete bindings)
- Use clk_hw pointer instead of fw_name for acm_aud_clk[0-1]_sel clocks
on i.MX8Q as parents in ACM provider
- Add i.MX95 NETCMIX support to the block control provider
- Fix parents for ENETx_REF_SEL clocks on i.MX6UL
- Add USB clocks, resets and power domains on Renesas RZ/G3S
- Add Generic Timer (GTM), I2C Bus Interface (RIIC), SD/MMC Host
Interface (SDHI) and Watchdog Timer (WDT) clocks and resets on
Renesas RZ/V2H
- Add PCIe, PWM, and CAN-FD clocks on Renesas R-Car V4M
- Add LCD controller clocks and resets on Renesas RZ/G2UL
- Add DMA clocks and resets on Renesas RZ/G3S
- Add fractional multiplication PLL support on Renesas R-Car Gen4
- Document support for the Renesas RZ/G2M v3.0 (r8a774a3) SoC
- Support for the Microchip SAM9X7 SoC as follows:
- Updates for the Microchip PLL drivers
- DT binding documentation updates (for the new clock driver and for
the slow clock controller that SAM9X7 is using)
- A fix for the Microchip SAMA7G5 clock driver to avoid allocating more
memory than necessary
- Constify some Amlogic structs
- Add SM1 eARC clocks for Amlogic
- Introduce a symbol namespace for Amlogic clock specific symbols
- Add reset controller support to audiomix block control on i.MX
- Add CLK_SET_RATE_PARENT flag to all audiomix clocks and to
i.MX7D lcdif_pixel_src clock
- Fix parent clocks for earc_phy and audpll on i.MX8MP
- Fix default parents for enet[12]_ref_sel on i.MX6UL
- Add ops in composite 8M and 93 that allow no-op on disable
- Add check for PCC present bit on composite 7ULP register
- Fix fractional part for fracn-gppll on prepare in i.MX
- Fix clock tree update for TF-A managed clocks on i.MX8M
- Drop CLK_SET_PARENT_GATE for DRAM mux on i.MX7D
- Add the SAI7 IPG clock for i.MX8MN
- Mark the 'nand_usdhc_bus' clock as non-critical on i.MX8MM
- Add LVDS bypass clocks on i.MX8QXP
- Add muxes for MIPI and PHY ref clocks on i.MX
- Reorder dc0_bypass0_clk, lcd_pxl and dc1_disp clocks on i.MX8QXP
- Add 1039.5MHz and 800MHz rates to fracn-gppll table on i.MX
- Add CLK_SET_RATE_PARENT for media_disp pixel clocks on i.MX8QXP
- Add some module descriptions to the i.MX generic and the
i.MXRT1050 driver
- Fix return value for bypass for composite i.MX7ULP
- Move Mediatek clk bindings to clock/
- Convert some more clk bindings to dt schema
-----BEGIN PGP SIGNATURE-----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=XmiQ
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The core clk framework is left largely untouched this time around
except for support for the newly ratified DT property
'assigned-clock-rates-u64'.
I'm much more excited about the support for loading DT overlays from
KUnit tests so that we can test how the clk framework parses DT nodes
during clk registration. The clk framework has some places that are
highly DeviceTree dependent so this charts the path to extend the
KUnit tests to cover even more framework code in the future. I've got
some more tests on the list that use the DT overlay support, but they
uncovered issues with clk unregistration that I'm still working on
fixing.
Outside the core, the clk driver update pile is dominated by Qualcomm
and Renesas SoCs, making it fairly usual. Looking closer, there are
fixes for things all over the place, like adding missing clk
frequencies or moving defines for the number of clks out of DT binding
headers into the drivers. There are even conversions of DT bindings to
YAML and migration away from strings to describe clk topology. Overall
it doesn't look unusual so I expect the new drivers to be where we'll
have fixes in the coming weeks.
Core:
- KUnit tests for clk registration and fixed rate basic clk type
- A couple more devm helpers, one consumer and one provider
- Support for assigned-clock-rates-u64
New Drivers:
- Camera, display and GPU clocks on Qualcomm SM4450
- Camera clocks on Qualcomm SM8150
- Rockchip rk3576 clks
- Microchip SAM9X7 clks
- Renesas RZ/V2H(P) (R9A09G057) clks
Updates:
- Mark a bunch of struct freq_tbl const to reduce .data usage
- Add Qualcomm MSM8226 A7PLL and Regera PLL support
- Fix the Qualcomm Lucid 5LPE PLL configuration sequence to not reuse
Trion, as they do differ
- A number of fixes to the Qualcomm SM8550 display clock driver
- Fold Qualcomm SM8650 display clock driver into SM8550 one
- Add missing clocks and GDSCs needed for audio on Qualcomm MSM8998
- Add missing USB MP resets, GPLL9, and QUPv3 DFS to Qualcomm SC8180X
- Fix sdcc clk frequency tables on Qualcomm SC8180X
- Drop the Qualcomm SM8150 gcc_cpuss_ahb_clk_src
- Mark Qualcomm PCIe GDSCs as RET_ON on sm8250 and sm8540 to avoid
them turning off during suspend
- Use the HW_CTRL mechanism on Qualcomm SM8550 video clock controller
GDSCs
- Get rid of CLK_NR_CLKS defines in Rockchip DT binding headers
- Some fixes for Rockchip rk3228 and rk3588
- Exynos850: Add clock for Thermal Management Unit
- Exynos7885: Fix duplicated ID in the header, add missing TOP PLLs
and add clocks for USB block in the FSYS clock controller
- ExynosAutov9: Add DPUM clock controller
- ExynosAutov920: Add new (first) clock controllers: TOP and PERIC0
(and a bit more complete bindings)
- Use clk_hw pointer instead of fw_name for acm_aud_clk[0-1]_sel
clocks on i.MX8Q as parents in ACM provider
- Add i.MX95 NETCMIX support to the block control provider
- Fix parents for ENETx_REF_SEL clocks on i.MX6UL
- Add USB clocks, resets and power domains on Renesas RZ/G3S
- Add Generic Timer (GTM), I2C Bus Interface (RIIC), SD/MMC Host
Interface (SDHI) and Watchdog Timer (WDT) clocks and resets on
Renesas RZ/V2H
- Add PCIe, PWM, and CAN-FD clocks on Renesas R-Car V4M
- Add LCD controller clocks and resets on Renesas RZ/G2UL
- Add DMA clocks and resets on Renesas RZ/G3S
- Add fractional multiplication PLL support on Renesas R-Car Gen4
- Document support for the Renesas RZ/G2M v3.0 (r8a774a3) SoC
- Support for the Microchip SAM9X7 SoC as follows:
- Updates for the Microchip PLL drivers
- DT binding documentation updates (for the new clock driver and for
the slow clock controller that SAM9X7 is using)
- A fix for the Microchip SAMA7G5 clock driver to avoid allocating
more memory than necessary
- Constify some Amlogic structs
- Add SM1 eARC clocks for Amlogic
- Introduce a symbol namespace for Amlogic clock specific symbols
- Add reset controller support to audiomix block control on i.MX
- Add CLK_SET_RATE_PARENT flag to all audiomix clocks and to i.MX7D
lcdif_pixel_src clock
- Fix parent clocks for earc_phy and audpll on i.MX8MP
- Fix default parents for enet[12]_ref_sel on i.MX6UL
- Add ops in composite 8M and 93 that allow no-op on disable
- Add check for PCC present bit on composite 7ULP register
- Fix fractional part for fracn-gppll on prepare in i.MX
- Fix clock tree update for TF-A managed clocks on i.MX8M
- Drop CLK_SET_PARENT_GATE for DRAM mux on i.MX7D
- Add the SAI7 IPG clock for i.MX8MN
- Mark the 'nand_usdhc_bus' clock as non-critical on i.MX8MM
- Add LVDS bypass clocks on i.MX8QXP
- Add muxes for MIPI and PHY ref clocks on i.MX
- Reorder dc0_bypass0_clk, lcd_pxl and dc1_disp clocks on i.MX8QXP
- Add 1039.5MHz and 800MHz rates to fracn-gppll table on i.MX
- Add CLK_SET_RATE_PARENT for media_disp pixel clocks on i.MX8QXP
- Add some module descriptions to the i.MX generic and the i.MXRT1050
driver
- Fix return value for bypass for composite i.MX7ULP
- Move Mediatek clk bindings to clock/
- Convert some more clk bindings to dt schema"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (180 commits)
clk: Switch back to struct platform_driver::remove()
dt-bindings: clock, reset: fix top-comment indentation rk3576 headers
clk: rockchip: remove unused mclk_pdm0_p/pdm0_p definitions
clk: provide devm_clk_get_optional_enabled_with_rate()
clk: fixed-rate: add devm_clk_hw_register_fixed_rate_parent_data()
clk: imx6ul: fix clock parent for IMX6UL_CLK_ENETx_REF_SEL
clk: renesas: r9a09g057: Add clock and reset entries for GTM/RIIC/SDHI/WDT
clk: renesas: rzv2h: Add support for dynamic switching divider clocks
clk: renesas: r9a08g045: Add clocks, resets and power domains for USB
clk: rockchip: fix error for unknown clocks
clk: rockchip: rk3588: drop unused code
clk: rockchip: Add clock controller for the RK3576
clk: rockchip: Add new pll type pll_rk3588_ddr
dt-bindings: clock, reset: Add support for rk3576
dt-bindings: clock: rockchip,rk3588-cru: drop unneeded assigned-clocks
clk: rockchip: rk3588: Fix 32k clock name for pmu_24m_32k_100m_src_p
clk: imx95: enable the clock of NETCMIX block control
dt-bindings: clock: add RMII clock selection
dt-bindings: clock: add i.MX95 NETCMIX block control
clk: imx: imx8: Use clk_hw pointer for self registered clock in clk_parent_data
...
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all clk drivers to use .remove(), with the eventual goal to drop
struct platform_driver::remove_new(). As .remove() and .remove_new() have
the same prototypes, conversion is done by just changing the structure
member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20240909144026.870565-2-u.kleine-koenig@baylibre.com
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be> # renesas
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The psc->div[] array has psc->num_div elements. These values come from
when we call clk_hw_register_div(). It's adc_divisors and
ARRAY_SIZE(adc_divisors)) and so on. So this condition needs to be >=
instead of > to prevent an out of bounds read.
Fixes: 9645ccc7bd ("ep93xx: clock: convert in-place to COMMON_CLK")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Reviewed-by: Nikita Shubin <nikita.shubin@maquefel.me>
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/1caf01ad4c0a8069535813c26c7f0b8ea011155e.camel@linaro.org
[arnd: the original patch was for arch/arm/mach-ep93xx/clock.c,
but the same bug ended up in arch/arm/mach-ep93xx/clock.c.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
When configured as a lodable module, this driver produces
a build time warning:
ERROR: modpost: missing MODULE_LICENSE() in drivers/clk/clk-ep93xx.o
All all three tags for license, author and description based
on the header.
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Rewrite EP93xx clock driver located in arch/arm/mach-ep93xx/clock.c
trying to do everything the device tree way:
- provide clock acces via of
- drop clk_hw_register_clkdev
- drop init code and use module_auxiliary_driver
Co-developed-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Nikita Shubin <nikita.shubin@maquefel.me>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
When -Wunused-const-variable is enabled (not the default),
there is a warning about two definitions in this file:
In file included from drivers/clk/rockchip/clk-rk3576.c:14:
drivers/clk/rockchip/clk-rk3576.c:334:7: error: 'mclk_pdm0_p' defined but not used [-Werror=unused-const-variable=]
334 | PNAME(mclk_pdm0_p) = { "mclk_pdm0_src_top", "xin24m" };
| ^~~~~~~~~~~
drivers/clk/rockchip/clk.h:564:43: note: in definition of macro 'PNAME'
564 | #define PNAME(x) static const char *const x[] __initconst
| ^
drivers/clk/rockchip/clk-rk3576.c:333:7: error: 'pdm0_p' defined but not used [-Werror=unused-const-variable=]
333 | PNAME(pdm0_p) = { "clk_pdm0_src_top", "xin24m" };
| ^~~~~~
drivers/clk/rockchip/clk.h:564:43: note: in definition of macro 'PNAME'
564 | #define PNAME(x) static const char *const x[] __initconst
| ^
Remove them for the moment. If they are needed later, they can
be added back at that point.
Fixes: cc40f5baa9 ("clk: rockchip: Add clock controller for the RK3576")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240909121116.254036-1-arnd@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
There are clock users in the kernel that can't use
devm_clk_get_optional_enabled() as they need to set rate after getting
the clock and before enabling it. Provide a managed helper that wraps
these operations in the correct order.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20240805-clk-new-helper-v2-1-e5fdd1e1d729@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Commit 4e197ee880 ("clk: imx6ul: add
ethernet refclock mux support") sets the internal clock as default
ethernet clock.
Since IMX6UL_CLK_ENET_REF cannot be parent for IMX6UL_CLK_ENET1_REF_SEL,
the call to clk_set_parent() fails. IMX6UL_CLK_ENET1_REF_125M is the correct
parent and shall be used instead.
Same applies for IMX6UL_CLK_ENET2_REF_SEL, for which IMX6UL_CLK_ENET2_REF_125M
is the correct parent.
Cc: stable@vger.kernel.org
Signed-off-by: Alex Michel <alex.michel@wiedemann-group.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/AS1P250MB0608F9CE4009DCE65C61EEDEA9922@AS1P250MB0608.EURP250.PROD.OUTLOOK.COM
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
A recent change started parking the RCG at an always on parent during
registration, something which specifically breaks handover from an early
serial console.
Quoting Stephen Boyd who fixed this issue for SM8550 [1]:
The QUPs aren't shared in a way that requires parking the RCG at
an always on parent in case some other entity turns on the clk.
The hardware is capable of setting a new frequency itself with
the DFS mode, so parking is unnecessary. Furthermore, there
aren't any GDSCs for these devices, so there isn't a possibility
of the GDSC turning on the clks for housekeeping purposes.
This wasn't a problem to mark these clks shared until we started
parking shared RCGs at clk registration time in commit
01a0a6cc8c ("clk: qcom: Park shared RCGs upon registration").
Parking at init is actually harmful to the UART when earlycon is
used. If the device is pumping out data while the frequency
changes you'll see garbage on the serial console until the
driver can probe and actually set a proper frequency.
Fixes: 01a0a6cc8c ("clk: qcom: Park shared RCGs upon registration")
Fixes: d65d005f9a ("clk: qcom: add sc8280xp GCC driver")
Link: https://lore.kernel.org/all/20240819233628.2074654-2-swboyd@chromium.org/ [1]
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240902070830.8535-1-johan+linaro@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add clocks, resets and power domains for USB modules available on the
Renesas RZ/G3S SoC.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20240822152801.602318-2-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
There is a clk == NULL check after the switch to check for
unsupported clk types. Since clk is re-assigned in a loop,
this check is useless right now for anything but the first
round. Let's fix this up by assigning clk = NULL in the
loop before the switch statement.
Fixes: a245fecbb8 ("clk: rockchip: add basic infrastructure for clock branches")
Cc: stable@vger.kernel.org
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
[added fixes + stable-cc]
Link: https://lore.kernel.org/r/20240325193609.237182-6-sebastian.reichel@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
All clocks are registered early using CLK_OF_DECLARE(), which marks
the DT node as processed. For the processed DT node the probe routine
is never called. Thus this whole code is never executed. This could
be "fixed" by using CLK_OF_DECLARE_DRIVER, which avoids marking the
DT node as processed. But then the probe routine would re-register
all the clocks by calling rk3588_clk_init() again.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20240325193609.237182-2-sebastian.reichel@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add notifier function for PLL0 clock. In the function, the cpu_root clock
should be operated by saving its current parent and setting a new safe
parent (osc clock) before setting the PLL0 clock rate. After setting PLL0
rate, it should be switched back to the original parent clock.
Fixes: e2c510d6d6 ("riscv: dts: starfive: Add cpu scaling for JH7110 SoC")
Cc: stable@vger.kernel.org
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Xingyu Wu <xingyu.wu@starfivetech.com>
Link: https://lore.kernel.org/r/20240826080430.179788-2-xingyu.wu@starfivetech.com
Reviewed-by: Hal Feng <hal.feng@starfivetech.com>
Tested-by: Michael Jeanson <mjeanson@efficios.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The QUPs aren't shared in a way that requires parking the RCG at an
always on parent in case some other entity turns on the clk. The
hardware is capable of setting a new frequency itself with the DFS mode,
so parking is unnecessary. Furthermore, there aren't any GDSCs for these
devices, so there isn't a possibility of the GDSC turning on the clks
for housekeeping purposes.
Like for the SM8550 GCC QUP clocks at [1], do not use shared clk_ops for QUPs.
[1] https://lore.kernel.org/all/20240827231237.1014813-3-swboyd@chromium.org/
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240829-topic-sm8650-upstream-fix-qup-clk-rcg-shared-v1-1-7ecdbc672187@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Amit Pundir reports that audio and USB-C host mode stops working if the
gcc_usb30_prim_master_clk_src clk is registered and
clk_rcg2_shared_init() parks it on XO. Skip parking this clk at
registration time to fix those issues.
Partially revert commit 01a0a6cc8c ("clk: qcom: Park shared RCGs upon
registration") by skipping the parking bit for this clk, but keep the
part where we cache the config register. That's still necessary to
figure out the true parent of the clk at registration time.
Fixes: 01a0a6cc8c ("clk: qcom: Park shared RCGs upon registration")
Fixes: 929c75d575 ("clk: qcom: gcc-sm8550: Mark RCGs shared where applicable")
Cc: Konrad Dybcio <konradybcio@kernel.org>
Cc: Bjorn Andersson <andersson@kernel.org>
Cc: Taniya Das <quic_tdas@quicinc.com>
Reported-by: Amit Pundir <amit.pundir@linaro.org>
Closes: https://lore.kernel.org/CAMi1Hd1KQBE4kKUdAn8E5FV+BiKzuv+8FoyWQrrTHPDoYTuhgA@mail.gmail.com
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20240819233628.2074654-3-swboyd@chromium.org
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The QUPs aren't shared in a way that requires parking the RCG at an
always on parent in case some other entity turns on the clk. The
hardware is capable of setting a new frequency itself with the DFS mode,
so parking is unnecessary. Furthermore, there aren't any GDSCs for these
devices, so there isn't a possibility of the GDSC turning on the clks
for housekeeping purposes.
This wasn't a problem to mark these clks shared until we started parking
shared RCGs at clk registration time in commit 01a0a6cc8c ("clk: qcom:
Park shared RCGs upon registration"). Parking at init is actually
harmful to the UART when earlycon is used. If the device is pumping out
data while the frequency changes you'll see garbage on the serial
console until the driver can probe and actually set a proper frequency.
Revert the QUP part of commit 929c75d575 ("clk: qcom: gcc-sm8550: Mark
RCGs shared where applicable") so that the QUPs don't get parked during
clk registration and break UART operations.
Fixes: 01a0a6cc8c ("clk: qcom: Park shared RCGs upon registration")
Fixes: 929c75d575 ("clk: qcom: gcc-sm8550: Mark RCGs shared where applicable")
Cc: Konrad Dybcio <konradybcio@kernel.org>
Cc: Bjorn Andersson <andersson@kernel.org>
Cc: Taniya Das <quic_tdas@quicinc.com>
Reported-by: Amit Pundir <amit.pundir@linaro.org>
Closes: https://lore.kernel.org/CAMi1Hd1KQBE4kKUdAn8E5FV+BiKzuv+8FoyWQrrTHPDoYTuhgA@mail.gmail.com
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20240819233628.2074654-2-swboyd@chromium.org
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add the clock and reset tree definitions for the new RK3576
SoC.
As opposed to the other rockchip CRU drivers, the GRF node is looked up
via compatible instead of a phandle, which simplifies the device tree
bindings.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Liang Chen <cl@rock-chips.com>
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com>
Reviewed-by: Elaine Zhang <zhangqing@rock-chips.com>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Dragan Simic <dsimic@manjaro.org>
Link: https://lore.kernel.org/r/0102019199a7781a-888440f0-a3f7-4a7d-a831-491260cbdfe7-000000@eu-west-1.amazonses.com
[dropped additional blank line at EOF in rst-rk3576.c
dropped the whole (non-)working as module part]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
That PLL type is similar to the other rk3588 pll types but the actual
rate is twice the configured rate.
Therefore, the returned calculated rate must be multiplied by two.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com>
Acked-by: Dragan Simic <dsimic@manjaro.org>
Link: https://lore.kernel.org/r/0102019199a76ec4-9d5846d4-d76a-4e69-a241-c88c2983d607-000000@eu-west-1.amazonses.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The 32kHz input clock is named "xin32k" in the driver,
so the name "32k" appears to be a typo in this case. Lets fix this.
Signed-off-by: Alexander Shiyan <eagle.alexander923@gmail.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Fixes: f1c506d152 ("clk: rockchip: add clock controller for the RK3588")
Link: https://lore.kernel.org/r/20240829052820.3604-1-eagle.alexander923@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The NETCMIX block control consists of registers for configuration of
peripherals in the NETC domain, so enable the clock of NETCMIX to
support the configuration.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20240829011849.364987-4-wei.fang@nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
"acm_aud_clk0_sel" and "acm_aud_clk1_sel" are registered by this ACM
driver, but they are the parent clocks for other clocks, in order to
use assigned-clock-parents in device tree, the ".fw_name" can't be used,
need to assign the clk_hw pointer for the imx8qm_mclk_sels[],
imx8qxp_mclk_sels[], imx8dxl_mclk_sels[].
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/1720600860-18866-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
