Set the receiver level to something > 0 before calling imx_uart_start_rx
in rs485_config. This is necessary to avoid an interrupt storm that
might prevent the system from booting. This was seen on an i.MX7 device
when the rs485-rts-active-low property was active in the device tree.
Fixes: 6d215f83e5 ("serial: imx: warn user when using unsupported configuration")
Cc: stable <stable@kernel.org>
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Link: https://lore.kernel.org/r/20240621153829.183780-1-eichest@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most of the colfires have up to 5 UARTs but MCF54418 has up-to 10 !
Change the maximum value authorized.
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@yoseli.org>
Cc: stable <stable@kernel.org>
Fixes: 2545cf6e94 ("m68knommu: allow 4 coldfire serial ports")
Link: https://lore.kernel.org/r/20240620-upstream-uart-v1-1-a9d0d95fb19e@yoseli.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Normally, the number of ports is indicated by the third digit of the
device ID on Moxa PCI serial boards. For example, `0x1121` indicates a
device with 2 ports.
However, `CP116E_A_A` and `CP116E_A_B` are exceptions; they have 8
ports, but the third digit of the device ID is `6`.
This patch introduces a function to retrieve the number of ports on Moxa
PCI serial boards, addressing the issue described above.
Fixes: 37058fd5d2 ("tty: serial: 8250: Add support for MOXA Mini PCIe boards")
Cc: stable <stable@kernel.org>
Signed-off-by: Crescent Hsieh <crescentcy.hsieh@moxa.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://lore.kernel.org/r/20240617063058.18866-1-crescentcy.hsieh@moxa.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some boards connect a GPIO to the reset pin, and the reset pin needs
to be set up correctly before accessing the chip.
Add a function to handle the chip reset. If the reset-gpios is defined
in the DT, do hardware reset through this GPIO, otherwise do software
reset as before.
Reviewed-by: Lech Perczak <lech.perczak@camlingroup.com>
Tested-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Link: https://lore.kernel.org/r/20240618112620.152848-2-hui.wang@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_isa_init_ports() uses home grown approach to make itself
a singleton. Instead, explicitly show that we initialise ISA ports
once by providing a helper function which calls the original function
via DO_ONCE() macro.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240606184841.3102545-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/tty/serial/8250/8250_base.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/tty/serial/8250/8250_pxa.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/tty/serial/8250/serial_cs.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/tty/serial/esp32_uart.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/tty/serial/esp32_acm.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/tty/serial/owl-uart.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/tty/n_hdlc.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/tty/n_gsm.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/tty/ttynull.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/tty/goldfish.o
Add all missing invocations of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://lore.kernel.org/r/20240607-md-drivers-tty-v1-1-50a7efb8bed8@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add serial support for RZ/V2H(P) SoC with earlycon.
The SCIF interface in the Renesas RZ/V2H(P) is similar to that available
in the RZ/G2L (R9A07G044) SoC, with the following differences:
- RZ/V2H(P) SoC has three additional interrupts: one for Tx end/Rx ready
and two for Rx and Tx buffer full, all of which are edge-triggered.
- RZ/V2H(P) supports asynchronous mode, whereas RZ/G2L supports both
synchronous and asynchronous modes.
- There are differences in the configuration of certain registers such
as SCSMR, SCFCR, and SCSPTR between the two SoCs.
To handle these differences on RZ/V2H(P) SoC SCIx_RZV2H_SCIF_REGTYPE
is added.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240604170513.522631-6-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some SoCs like StarFive JH7110 require two or more resets.
So change to use the reset array API to get resets.
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
Link: https://lore.kernel.org/r/20240604084729.57239-3-hal.feng@starfivetech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This enables the admin to abort the BPF scheduler and revert to CFS anytime.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: David Vernet <dvernet@meta.com>
Acked-by: Josh Don <joshdon@google.com>
Acked-by: Hao Luo <haoluo@google.com>
Acked-by: Barret Rhoden <brho@google.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmZvTbAeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGVksIAJEn4a9IVM8FNCJy
Dxo0BItD1/qJ5mLDptqUFRKlxInjbojofz5CyoeIeXb0DwRfB16ALXqNXAkd3APi
saoOpfjFsg2H2OqL9CHdkzWcJEAq2lDnL0zaOjumeDVu/EyeT+tC4e4hq1e6Bm0E
fPC5ms2b+07DF9Rg6/DW8yPbdM5n6Mz1bRd3fQOIgvpM3yGOyGztEBgTRub/ZUgH
5pNJauknFAZgdiWhgNpc+lPWYZbgHKULQPhUBPdVhDIXPtQNUlKgNTQc6+L0Nmbb
K1sG1q7FLeMJOTFGQfD4r26X5DNQUi894q/9SX8X7rcrECdJKcw2WjVyB4myADpf
ae2gP+A=
=XjWP
-----END PGP SIGNATURE-----
Merge tag 'v6.10-rc4' into tty-next
We need the tty/serial fixes in here as well
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d492164381
("serial: sc16is7xx: split into core and I2C/SPI parts (core)")
removed Kconfig SPI_MASTER or I2C dependency for SERIAL_SC16IS7XX (core).
This removal was done because I inadvertently misinterpreted some review
comments.
Because of that, the driver question now pops up if both I2C and
SPI_MASTER are disabled.
Re-add Kconfig SPI_MASTER or I2C dependency to fix the problem.
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes: d492164381 ("serial: sc16is7xx: split into core and I2C/SPI parts (core)")
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240603152601.3689319-3-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d492164381
("serial: sc16is7xx: split into core and I2C/SPI parts (core)")
renamed SERIAL_SC16IS7XX_CORE by SERIAL_SC16IS7XX. This means that some
configs should have been updated when I submitted the original patch, but
unfortunately they were not. Geert mentioned for example:
arch/mips/configs/cu1??0-neo_defconfig
Rename SERIAL_SC16IS7XX to SERIAL_SC16IS7XX_CORE so that existing configs
will still work correctly.
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes: d492164381 ("serial: sc16is7xx: split into core and I2C/SPI parts (core)")
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240603152601.3689319-2-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recently, suspend testing on sc7180-trogdor based devices has started
to sometimes fail with messages like this:
port a88000.serial:0.0: PM: calling pm_runtime_force_suspend+0x0/0xf8 @ 28934, parent: a88000.serial:0
port a88000.serial:0.0: PM: dpm_run_callback(): pm_runtime_force_suspend+0x0/0xf8 returns -16
port a88000.serial:0.0: PM: pm_runtime_force_suspend+0x0/0xf8 returned -16 after 33 usecs
port a88000.serial:0.0: PM: failed to suspend: error -16
I could reproduce these problems by logging in via an agetty on the
debug serial port (which was _not_ used for kernel console) and
running:
cat /var/log/messages
...and then (via an SSH session) forcing a few suspend/resume cycles.
Tracing through the code and doing some printf()-based debugging shows
that the -16 (-EBUSY) comes from the recently added
serial_port_runtime_suspend().
The idea of the serial_port_runtime_suspend() function is to prevent
the port from being _runtime_ suspended if it still has bytes left to
transmit. Having bytes left to transmit isn't a reason to block
_system_ suspend, though. If a serdev device in the kernel needs to
block system suspend it should block its own suspend and it can use
serdev_device_wait_until_sent() to ensure bytes are sent.
The DEFINE_RUNTIME_DEV_PM_OPS() used by the serial_port code means
that the system suspend function will be pm_runtime_force_suspend().
In pm_runtime_force_suspend() we can see that before calling the
runtime suspend function we'll call pm_runtime_disable(). This should
be a reliable way to detect that we're called from system suspend and
that we shouldn't look for busyness.
Fixes: 43066e3222 ("serial: port: Don't suspend if the port is still busy")
Cc: stable@vger.kernel.org
Reviewed-by: Tony Lindgren <tony.lindgren@linux.intel.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20240531080914.v3.1.I2395e66cf70c6e67d774c56943825c289b9c13e4@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The FIFO is 64 bytes, but the FCR is configured to fire the TX interrupt
when the FIFO is half empty (bit 3 = 0). Thus, we should only write 32
bytes when a TX interrupt occurs.
This fixes a problem observed on the PXA168 that dropped a bunch of TX
bytes during large transmissions.
Fixes: ab28f51c77 ("serial: rewrite pxa2xx-uart to use 8250_core")
Signed-off-by: Doug Brown <doug@schmorgal.com>
Link: https://lore.kernel.org/r/20240519191929.122202-1-doug@schmorgal.com
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit d9666dfb31.
The container of the struct dw8250_port_data is private to the actual
driver. In particular, 8250_lpss and 8250_dw use different data types
that are assigned to the UART port private_data. Hence, it must not
be used outside the specific driver.
Fix the mistake made in the past by moving the respective definitions
to the specific driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240514190730.2787071-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The container of the struct dw8250_port_data is private to the actual
driver. In particular, 8250_lpss and 8250_dw use different data types
that are assigned to the UART port private_data. Hence, it must not
be used outside the specific driver.
Currently the only cpr_val is required by the common code, make it
be available via struct dw8250_port_data.
This fixes the UART breakage on Intel Galileo boards.
Fixes: 593dea000b ("serial: 8250: dw: Allow to use a fallback CPR value if not synthesized")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240514190730.2787071-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When lookahead has "consumed" some characters (la_count > 0),
n_tty_receive_buf_standard() and n_tty_receive_buf_closing() for
characters beyond the la_count are given wrong cp/fp offsets which
leads to duplicating and losing some characters.
If la_count > 0, correct buffer pointers and make count consistent too
(the latter is not strictly necessary to fix the issue but seems more
logical to adjust all variables immediately to keep state consistent).
Reported-by: Vadym Krevs <vkrevs@yahoo.com>
Fixes: 6bb6fa6908 ("tty: Implement lookahead to process XON/XOFF timely")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218834
Tested-by: Vadym Krevs <vkrevs@yahoo.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240514140429.12087-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Extract platform driver to a separate module for better maintenance
and to reduce churn on 8250_core part changes when it's solely related
to the former. No functional changes intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Sunil V L <sunilvl@ventanamicro.com>
Tested-by: Sunil V L <sunilvl@ventanamicro.com>
Link: https://lore.kernel.org/r/20240506140308.4040735-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Extract RSA bits to a separate module for better maintenance
and to reduce a churn on 8250_core part changes when it's solely
related to the former. No functional changes intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240506140308.4040735-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
struct imx_port does have a struct uart_port as its first member, so
the current code works, but it is not how kernel code is usually
written.
Similar to many other serial drivers, introduce and use a
to_imx_port() helper based on container_of(). No functional change.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20240528094022.2161066-1-linux@rasmusvillemoes.dk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A LED trigger's activate() callback gets called when the LED trigger
gets activated for a specific LED, so that the trigger code can ensure
the LED state matches the current state of the trigger condition.
led_trigger_event() is intended for trigger condition state changes and
iterates over _all_ LEDs which are controlled by this trigger changing
the brightness of each of them.
In the activate() case only the brightness of the LED which is being
activated needs to change and that LED is passed as an argument to
activate(), switch to led_set_brightness() to only change the brightness
of the LED being activated.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20240511152030.4848-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add `__free` function attribute to `ap` and `match` pointer
initialisations which ensure that the pointers are freed as soon as they
go out of scope, thus removing the need to manually free them using
`of_node_put`.
This also removes the need for the `goto` statement and the `rc`
variable.
Suggested-by: Julia Lawall <julia.lawall@inria.fr>
Signed-off-by: Shresth Prasad <shresthprasad7@gmail.com>
Link: https://lore.kernel.org/r/20240518114051.18125-3-shresthprasad7@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename console_replay_all() to console_try_replay_all() to make
clear that the implementation is best effort. Also, the function
should not be called in NMI context as it takes locks, so update
the comment in code.
Fixes: 693f75b91a ("printk: Add function to replay kernel log on consoles")
Fixes: 1b743485e2 ("tty/sysrq: Replay kernel log messages on consoles via sysrq")
Suggested-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Shimoyashiki Taichi <taichi.shimoyashiki@sony.com>
Signed-off-by: Sreenath Vijayan <sreenath.vijayan@sony.com>
Link: https://lore.kernel.org/r/Zlguq/wU21Z8MqI4@sreenath.vijayan@sony.com
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Here are some small TTY and Serial driver fixes that missed the
6.9-final merge window, but have been in my tree for weeks (my fault,
travel caused me to miss this.)
These fixes include:
- more n_gsm fixes for reported problems
- 8520_mtk driver fix
- 8250_bcm7271 driver fix
- sc16is7xx driver fix
All of these have been in linux-next for weeks without any reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZlBGKQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylOkwCfUOa00YQt3jJwBEC9bQUprW1z95MAoKW00V5g
UJgQ7+1d+o4bT/ib5xpj
=/O0m
-----END PGP SIGNATURE-----
Merge tag 'tty-6.10-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some small TTY and Serial driver fixes that missed the
6.9-final merge window, but have been in my tree for weeks (my fault,
travel caused me to miss this)
These fixes include:
- more n_gsm fixes for reported problems
- 8520_mtk driver fix
- 8250_bcm7271 driver fix
- sc16is7xx driver fix
All of these have been in linux-next for weeks without any reported
problems"
* tag 'tty-6.10-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: sc16is7xx: fix bug in sc16is7xx_set_baud() when using prescaler
serial: 8250_bcm7271: use default_mux_rate if possible
serial: 8520_mtk: Set RTS on shutdown for Rx in-band wakeup
tty: n_gsm: fix missing receive state reset after mode switch
tty: n_gsm: fix possible out-of-bounds in gsm0_receive()
Here is the big set of tty/serial driver changes for 6.10-rc1. Included
in here are:
- Usual good set of api cleanups and evolution by Jiri Slaby to make
the serial interfaces move out of the 1990's by using kfifos instead
of hand-rolling their own logic.
- 8250_exar driver updates
- max3100 driver updates
- sc16is7xx driver updates
- exar driver updates
- sh-sci driver updates
- tty ldisc api addition to help refuse bindings
- other smaller serial driver updates
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZk4Cvg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymqpwCgnHU1NeBBUsvoSDOLk5oApIQ4jVgAn102jWlw
3dNDhA4i3Ay/mZdv8/Kj
=TI+P
-----END PGP SIGNATURE-----
Merge tag 'tty-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is the big set of tty/serial driver changes for 6.10-rc1.
Included in here are:
- Usual good set of api cleanups and evolution by Jiri Slaby to make
the serial interfaces move out of the 1990's by using kfifos
instead of hand-rolling their own logic.
- 8250_exar driver updates
- max3100 driver updates
- sc16is7xx driver updates
- exar driver updates
- sh-sci driver updates
- tty ldisc api addition to help refuse bindings
- other smaller serial driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (113 commits)
serial: Clear UPF_DEAD before calling tty_port_register_device_attr_serdev()
serial: imx: Raise TX trigger level to 8
serial: 8250_pnp: Simplify "line" related code
serial: sh-sci: simplify locking when re-issuing RXDMA fails
serial: sh-sci: let timeout timer only run when DMA is scheduled
serial: sh-sci: describe locking requirements for invalidating RXDMA
serial: sh-sci: protect invalidating RXDMA on shutdown
tty: add the option to have a tty reject a new ldisc
serial: core: Call device_set_awake_path() for console port
dt-bindings: serial: brcm,bcm2835-aux-uart: convert to dtschema
tty: serial: uartps: Add support for uartps controller reset
arm64: zynqmp: Add resets property for UART nodes
dt-bindings: serial: cdns,uart: Add optional reset property
serial: 8250_pnp: Switch to DEFINE_SIMPLE_DEV_PM_OPS()
serial: 8250_exar: Keep the includes sorted
serial: 8250_exar: Make type of bit the same in exar_ee_*_bit()
serial: 8250_exar: Use BIT() in exar_ee_read()
serial: 8250_exar: Switch to use dev_err_probe()
serial: 8250_exar: Return directly from switch-cases
serial: 8250_exar: Decrease indentation level
...
- Switch read and write software bits for PUDs
- Add missing hardware bits for PUDs and PMDs
- Generate unwind information for C modules to fix GDB unwind
error for vDSO functions
- Create .build-id links for unstripped vDSO files to enable
vDSO debugging with symbols
- Use standard stack frame layout for vDSO generated stack frames
to manually walk stack frames without DWARF information
- Rework perf_callchain_user() and arch_stack_walk_user() functions
to reduce code duplication
- Skip first stack frame when walking user stack
- Add basic checks to identify invalid instruction pointers when
walking stack frames
- Introduce and use struct stack_frame_vdso_wrapper within vDSO user
wrapper code to automatically generate an asm-offset define. Also
use STACK_FRAME_USER_OVERHEAD instead of STACK_FRAME_OVERHEAD to
document that the code works with user space stack
- Clear the backchain of the extra stack frame added by the vDSO user
wrapper code. This allows the user stack walker to detect and skip
the non-standard stack frame. Without this an incorrect instruction
pointer would be added to stack traces.
- Rewrite psw_idle() function in C to ease maintenance and further
enhancements
- Remove get_vtimer() function and use get_cpu_timer() instead
- Mark psw variable in __load_psw_mask() as __unitialized to avoid
superfluous clearing of PSW
- Remove obsolete and superfluous comment about removed TIF_FPU flag
- Replace memzero_explicit() and kfree() with kfree_sensitive() to
fix warnings reported by Coccinelle
- Wipe sensitive data and all copies of protected- or secure-keys
from stack when an IOCTL fails
- Both do_airq_interrupt() and do_io_interrupt() functions set
CIF_NOHZ_DELAY flag. Move it in do_io_irq() to simplify the code
- Provide iucv_alloc_device() and iucv_release_device() helpers,
which can be used to deduplicate more or less identical IUCV
device allocation and release code in four different drivers
- Make use of iucv_alloc_device() and iucv_release_device()
helpers to get rid of quite some code and also remove a
cast to an incompatible function (clang W=1)
- There is no user of iucv_root outside of the core IUCV code left.
Therefore remove the EXPORT_SYMBOL
- __apply_alternatives() contains a runtime check which verifies
that the size of the to be patched code area is even. Convert
this to a compile time check
- Increase size of buffers for sending z/VM CP DIAGNOSE X'008'
commands from 128 to 240
- Do not accept z/VM CP DIAGNOSE X'008' commands longer than
maximally allowed
- Use correct defines IPL_BP_NVME_LEN and IPL_BP0_NVME_LEN instead
of IPL_BP_FCP_LEN and IPL_BP0_FCP_LEN ones to initialize NVMe
reIPL block on 'scp_data' sysfs attribute update
- Initialize the correct fields of the NVMe dump block, which
were confused with FCP fields
- Refactor macros for 'scp_data' (re-)IPL sysfs attribute to
reduce code duplication
- Introduce 'scp_data' sysfs attribute for dump IPL to allow tools
such as dumpconf passing additional kernel command line parameters
to a stand-alone dumper
- Rework the CPACF query functions to use the correct RRE or RRF
instruction formats and set instruction register fields correctly
- Instead of calling BUG() at runtime force a link error during
compile when a unsupported opcode is used with __cpacf_query()
or __cpacf_check_opcode() functions
- Fix a crash in ap_parse_bitmap_str() function on /sys/bus/ap/apmask
or /sys/bus/ap/aqmask sysfs file update with a relative mask value
- Fix "bindings complete" udev event which should be sent once all AP
devices have been bound to device drivers and again when unbind/bind
actions take place and all AP devices are bound again
- Facility list alt_stfle_fac_list is nowhere used in the decompressor,
therefore remove it there
- Remove custom kprobes insn slot allocator in favour of the standard
module_alloc() one, since kernel image and module areas are located
within 4GB
- Use kvcalloc() instead of kvmalloc_array() in zcrypt driver to avoid
calling memset() with a large byte count and get rid of the sparse
warning as result
-----BEGIN PGP SIGNATURE-----
iI0EABYIADUWIQQrtrZiYVkVzKQcYivNdxKlNrRb8AUCZkyx2BccYWdvcmRlZXZA
bGludXguaWJtLmNvbQAKCRDNdxKlNrRb8PYZAP9KxEfTyUmIh61Gx8+m3BW5dy7p
E2Q8yotlUpGj49ul+AD8CEAyTiWR95AlMOVZZLV/0J7XIjhALvpKAGfiJWkvXgc=
=pife
-----END PGP SIGNATURE-----
Merge tag 's390-6.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull more s390 updates from Alexander Gordeev:
- Switch read and write software bits for PUDs
- Add missing hardware bits for PUDs and PMDs
- Generate unwind information for C modules to fix GDB unwind error for
vDSO functions
- Create .build-id links for unstripped vDSO files to enable vDSO
debugging with symbols
- Use standard stack frame layout for vDSO generated stack frames to
manually walk stack frames without DWARF information
- Rework perf_callchain_user() and arch_stack_walk_user() functions to
reduce code duplication
- Skip first stack frame when walking user stack
- Add basic checks to identify invalid instruction pointers when
walking stack frames
- Introduce and use struct stack_frame_vdso_wrapper within vDSO user
wrapper code to automatically generate an asm-offset define. Also use
STACK_FRAME_USER_OVERHEAD instead of STACK_FRAME_OVERHEAD to document
that the code works with user space stack
- Clear the backchain of the extra stack frame added by the vDSO user
wrapper code. This allows the user stack walker to detect and skip
the non-standard stack frame. Without this an incorrect instruction
pointer would be added to stack traces.
- Rewrite psw_idle() function in C to ease maintenance and further
enhancements
- Remove get_vtimer() function and use get_cpu_timer() instead
- Mark psw variable in __load_psw_mask() as __unitialized to avoid
superfluous clearing of PSW
- Remove obsolete and superfluous comment about removed TIF_FPU flag
- Replace memzero_explicit() and kfree() with kfree_sensitive() to fix
warnings reported by Coccinelle
- Wipe sensitive data and all copies of protected- or secure-keys from
stack when an IOCTL fails
- Both do_airq_interrupt() and do_io_interrupt() functions set
CIF_NOHZ_DELAY flag. Move it in do_io_irq() to simplify the code
- Provide iucv_alloc_device() and iucv_release_device() helpers, which
can be used to deduplicate more or less identical IUCV device
allocation and release code in four different drivers
- Make use of iucv_alloc_device() and iucv_release_device() helpers to
get rid of quite some code and also remove a cast to an incompatible
function (clang W=1)
- There is no user of iucv_root outside of the core IUCV code left.
Therefore remove the EXPORT_SYMBOL
- __apply_alternatives() contains a runtime check which verifies that
the size of the to be patched code area is even. Convert this to a
compile time check
- Increase size of buffers for sending z/VM CP DIAGNOSE X'008' commands
from 128 to 240
- Do not accept z/VM CP DIAGNOSE X'008' commands longer than maximally
allowed
- Use correct defines IPL_BP_NVME_LEN and IPL_BP0_NVME_LEN instead of
IPL_BP_FCP_LEN and IPL_BP0_FCP_LEN ones to initialize NVMe reIPL
block on 'scp_data' sysfs attribute update
- Initialize the correct fields of the NVMe dump block, which were
confused with FCP fields
- Refactor macros for 'scp_data' (re-)IPL sysfs attribute to reduce
code duplication
- Introduce 'scp_data' sysfs attribute for dump IPL to allow tools such
as dumpconf passing additional kernel command line parameters to a
stand-alone dumper
- Rework the CPACF query functions to use the correct RRE or RRF
instruction formats and set instruction register fields correctly
- Instead of calling BUG() at runtime force a link error during compile
when a unsupported opcode is used with __cpacf_query() or
__cpacf_check_opcode() functions
- Fix a crash in ap_parse_bitmap_str() function on /sys/bus/ap/apmask
or /sys/bus/ap/aqmask sysfs file update with a relative mask value
- Fix "bindings complete" udev event which should be sent once all AP
devices have been bound to device drivers and again when unbind/bind
actions take place and all AP devices are bound again
- Facility list alt_stfle_fac_list is nowhere used in the decompressor,
therefore remove it there
- Remove custom kprobes insn slot allocator in favour of the standard
module_alloc() one, since kernel image and module areas are located
within 4GB
- Use kvcalloc() instead of kvmalloc_array() in zcrypt driver to avoid
calling memset() with a large byte count and get rid of the sparse
warning as result
* tag 's390-6.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (39 commits)
s390/zcrypt: Use kvcalloc() instead of kvmalloc_array()
s390/kprobes: Remove custom insn slot allocator
s390/boot: Remove alt_stfle_fac_list from decompressor
s390/ap: Fix bind complete udev event sent after each AP bus scan
s390/ap: Fix crash in AP internal function modify_bitmap()
s390/cpacf: Make use of invalid opcode produce a link error
s390/cpacf: Split and rework cpacf query functions
s390/ipl: Introduce sysfs attribute 'scp_data' for dump ipl
s390/ipl: Introduce macros for (re)ipl sysfs attribute 'scp_data'
s390/ipl: Fix incorrect initialization of nvme dump block
s390/ipl: Fix incorrect initialization of len fields in nvme reipl block
s390/ipl: Do not accept z/VM CP diag X'008' cmds longer than max length
s390/ipl: Fix size of vmcmd buffers for sending z/VM CP diag X'008' cmds
s390/alternatives: Convert runtime sanity check into compile time check
s390/iucv: Unexport iucv_root
tty: hvc-iucv: Make use of iucv_alloc_device()
s390/smsgiucv_app: Make use of iucv_alloc_device()
s390/netiucv: Make use of iucv_alloc_device()
s390/vmlogrdr: Make use of iucv_alloc_device()
s390/iucv: Provide iucv_alloc_device() / iucv_release_device()
...
-----BEGIN PGP SIGNATURE-----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=xjoS
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Skip E820 checks for MCFG ECAM regions for new (2016+) machines,
since there's no requirement to describe them in E820 and some
platforms require ECAM to work (Bjorn Helgaas)
- Rename PCI_IRQ_LEGACY to PCI_IRQ_INTX to be more specific (Damien
Le Moal)
- Remove last user and pci_enable_device_io() (Heiner Kallweit)
- Wait for Link Training==0 to avoid possible race (Ilpo Järvinen)
- Skip waiting for devices that have been disconnected while
suspended (Ilpo Järvinen)
- Clear Secondary Status errors after enumeration since Master Aborts
and Unsupported Request errors are an expected part of enumeration
(Vidya Sagar)
MSI:
- Remove unused IMS (Interrupt Message Store) support (Bjorn Helgaas)
Error handling:
- Mask Genesys GL975x SD host controller Replay Timer Timeout
correctable errors caused by a hardware defect; the errors cause
interrupts that prevent system suspend (Kai-Heng Feng)
- Fix EDR-related _DSM support, which previously evaluated revision 5
but assumed revision 6 behavior (Kuppuswamy Sathyanarayanan)
ASPM:
- Simplify link state definitions and mask calculation (Ilpo
Järvinen)
Power management:
- Avoid D3cold for HP Pavilion 17 PC/1972 PCIe Ports, where BIOS
apparently doesn't know how to put them back in D0 (Mario
Limonciello)
CXL:
- Support resetting CXL devices; special handling required because
CXL Ports mask Secondary Bus Reset by default (Dave Jiang)
DOE:
- Support DOE Discovery Version 2 (Alexey Kardashevskiy)
Endpoint framework:
- Set endpoint BAR to be 64-bit if the driver says that's all the
device supports, in addition to doing so if the size is >2GB
(Niklas Cassel)
- Simplify endpoint BAR allocation and setting interfaces (Niklas
Cassel)
Cadence PCIe controller driver:
- Drop DT binding redundant msi-parent and pci-bus.yaml (Krzysztof
Kozlowski)
Cadence PCIe endpoint driver:
- Configure endpoint BARs to be 64-bit based on the BAR type, not the
BAR value (Niklas Cassel)
Freescale Layerscape PCIe controller driver:
- Convert DT binding to YAML (Frank Li)
MediaTek MT7621 PCIe controller driver:
- Add DT binding missing 'reg' property for child Root Ports
(Krzysztof Kozlowski)
- Fix theoretical string truncation in PHY name (Sergio Paracuellos)
NVIDIA Tegra194 PCIe controller driver:
- Return success for endpoint probe instead of falling through to the
failure path (Vidya Sagar)
Renesas R-Car PCIe controller driver:
- Add DT binding missing IOMMU properties (Geert Uytterhoeven)
- Add DT binding R-Car V4H compatible for host and endpoint mode
(Yoshihiro Shimoda)
Rockchip PCIe controller driver:
- Configure endpoint BARs to be 64-bit based on the BAR type, not the
BAR value (Niklas Cassel)
- Add DT binding missing maxItems to ep-gpios (Krzysztof Kozlowski)
- Set the Subsystem Vendor ID, which was previously zero because it
was masked incorrectly (Rick Wertenbroek)
Synopsys DesignWare PCIe controller driver:
- Restructure DBI register access to accommodate devices where this
requires Refclk to be active (Manivannan Sadhasivam)
- Remove the deinit() callback, which was only need by the
pcie-rcar-gen4, and do it directly in that driver (Manivannan
Sadhasivam)
- Add dw_pcie_ep_cleanup() so drivers that support PERST# can clean
up things like eDMA (Manivannan Sadhasivam)
- Rename dw_pcie_ep_exit() to dw_pcie_ep_deinit() to make it parallel
to dw_pcie_ep_init() (Manivannan Sadhasivam)
- Rename dw_pcie_ep_init_complete() to dw_pcie_ep_init_registers() to
reflect the actual functionality (Manivannan Sadhasivam)
- Call dw_pcie_ep_init_registers() directly from all the glue
drivers, not just those that require active Refclk from the host
(Manivannan Sadhasivam)
- Remove the "core_init_notifier" flag, which was an obscure way for
glue drivers to indicate that they depend on Refclk from the host
(Manivannan Sadhasivam)
TI J721E PCIe driver:
- Add DT binding J784S4 SoC Device ID (Siddharth Vadapalli)
- Add DT binding J722S SoC support (Siddharth Vadapalli)
TI Keystone PCIe controller driver:
- Add DT binding missing num-viewport, phys and phy-name properties
(Jan Kiszka)
Miscellaneous:
- Constify and annotate with __ro_after_init (Heiner Kallweit)
- Convert DT bindings to YAML (Krzysztof Kozlowski)
- Check for kcalloc() failure in of_pci_prop_intr_map() (Duoming
Zhou)"
* tag 'pci-v6.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (97 commits)
PCI: Do not wait for disconnected devices when resuming
x86/pci: Skip early E820 check for ECAM region
PCI: Remove unused pci_enable_device_io()
ata: pata_cs5520: Remove unnecessary call to pci_enable_device_io()
PCI: Update pci_find_capability() stub return types
PCI: Remove PCI_IRQ_LEGACY
scsi: vmw_pvscsi: Do not use PCI_IRQ_LEGACY instead of PCI_IRQ_LEGACY
scsi: pmcraid: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: mpt3sas: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: megaraid_sas: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: ipr: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: hpsa: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: arcmsr: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
wifi: rtw89: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
dt-bindings: PCI: rockchip,rk3399-pcie: Add missing maxItems to ep-gpios
Revert "genirq/msi: Provide constants for PCI/IMS support"
Revert "x86/apic/msi: Enable PCI/IMS"
Revert "iommu/vt-d: Enable PCI/IMS"
Revert "iommu/amd: Enable PCI/IMS"
Revert "PCI/MSI: Provide IMS (Interrupt Message Store) support"
...
Nine patches this cycle and they split into just three topics:
1. Adopt coccinelle's recommendation to adopt str_plural().
2. A set of seven patches to refactor kdb_read() to improve both code clarity
and it's discipline with respect to fixed size buffers. This isn't just a
refactor. Between them these also fix a cursor movement redraw problem and
two buffer overflows (one latent and one real, albeit difficult to
tickle).
3. Fix an NMI-safety problem when enqueuing kdb's keyboard reset code.
I wrote eight of the nine patches in this collection so many thanks to Doug
Anderson for the reviews. The changes that affects drivers/tty/serial is
acked by Greg KH.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
-----BEGIN PGP SIGNATURE-----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=vVUC
-----END PGP SIGNATURE-----
Merge tag 'kgdb-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/danielt/linux
Pull kgdb updates from Daniel Thompson:
"Nine patches this cycle and they split into just three topics:
- Adopt coccinelle's recommendation to adopt str_plural()
- A set of seven patches to refactor kdb_read() to improve both code
clarity and its discipline with respect to fixed size buffers.
This isn't just a refactor. Between them these also fix a cursor
movement redraw problem and two buffer overflows (one latent and
one real, albeit difficult to tickle).
- Fix an NMI-safety problem when enqueuing kdb's keyboard reset code
I wrote eight of the nine patches in this collection so many thanks to
Doug Anderson for the reviews. The changes that affects
drivers/tty/serial is acked by Greg KH"
* tag 'kgdb-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/danielt/linux:
serial: kgdboc: Fix NMI-safety problems from keyboard reset code
kdb: Simplify management of tmpbuffer in kdb_read()
kdb: Replace double memcpy() with memmove() in kdb_read()
kdb: Use format-specifiers rather than memset() for padding in kdb_read()
kdb: Merge identical case statements in kdb_read()
kdb: Fix console handling when editing and tab-completing commands
kdb: Use format-strings rather than '\0' injection in kdb_read()
kdb: Fix buffer overflow during tab-complete
kdb: Use str_plural() to fix Coccinelle warning
-----BEGIN PGP SIGNATURE-----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=y45P
-----END PGP SIGNATURE-----
Merge tag 'printk-for-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux
Pull printk updates from Petr Mladek:
- Use no_printk() instead of "if (0) printk()" constructs to avoid
generating printk index for messages disabled at compile time
- Remove deprecated strncpy/strcpy from printk.c
- Remove redundant CONFIG_BASE_FULL in favor of CONFIG_BASE_SMALL
* tag 'printk-for-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux:
printk: cleanup deprecated uses of strncpy/strcpy
printk: Remove redundant CONFIG_BASE_FULL
printk: Change type of CONFIG_BASE_SMALL to bool
printk: Fix LOG_CPU_MAX_BUF_SHIFT when BASE_SMALL is enabled
ceph: Use no_printk() helper
dyndbg: Use *no_printk() helpers
dev_printk: Add and use dev_no_printk()
printk: Let no_printk() use _printk()
Make use of iucv_alloc_device() to get rid of quite some code.
Acked-by: Alexandra Winter <wintera@linux.ibm.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240506194454.1160315-6-hca@linux.ibm.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
I had investigated dropping support for alpha EV5 and earlier a while
ago after noticing that this is the only supported CPU family
in the kernel without native byte access and that Debian has already
dropped support for this generation last year [1] in order to
improve performance for the newer machines.
This topic came up again when Paul E. McKenney noticed that
parts of the RCU code already rely on byte access and do not
work on alpha EV5 reliably, so we decided on using my series to
avoid the problem entirely.
Al Viro did another series for alpha to address all the known build
issues. I rebased his patches without any further changes and included
it as a baseline for my work here to avoid conflicts and allow
backporting the fixes to stable kernels for the now removed hardware
support as well.
-----BEGIN PGP SIGNATURE-----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=0Sgm
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-alpha' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull alpha updates from Arnd Bergmann:
"I had investigated dropping support for alpha EV5 and earlier a while
ago after noticing that this is the only supported CPU family in the
kernel without native byte access and that Debian has already dropped
support for this generation last year [1] in order to improve
performance for the newer machines.
This topic came up again when Paul McKenney noticed that parts of the
RCU code already rely on byte access and do not work on alpha EV5
reliably, so we decided on using my series to avoid the problem
entirely.
Al Viro did another series for alpha to address all the known build
issues. I rebased his patches without any further changes and included
it as a baseline for my work here to avoid conflicts and allow
backporting the fixes to stable kernels for the now removed hardware
support as well"
[ I dearly loved alpha back in the days, but the lack of byte and word
operations was a horrible mistake and made everything worse -
including very much the crazy IO contortions that resulted from it.
It certainly wasn't the only mistake in the architecture, but it's the
first-order issue.
So while it's a bit sad to see the support for my first alpha go away,
if you want to run museum hardware, maybe you should use museum
kernels.. - Linus ]
* tag 'asm-generic-alpha' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
alpha: drop pre-EV56 support
alpha: cabriolet: remove EV5 CPU support
alpha: remove LCA and APECS based machines
alpha: sable: remove early machine support
alpha: remove DECpc AXP150 (Jensen) support
alpha: trim the unused stuff from asm-offsets.c
alpha: jensen, t2 - make __EXTERN_INLINE same as for the rest
alpha: core_lca: take the unused functions out
alpha: missing includes
alpha: sys_sio: fix misspelled ifdefs
alpha: don't make functions public without a reason
alpha: add clone3() support
alpha: fix modversions for strcpy() et.al.
alpha: sort scr_mem{cpy,move}w() out
If a serdev_device_driver is already loaded for a serdev_tty_port when it
gets registered by tty_port_register_device_attr_serdev() then that
driver's probe() method will be called immediately.
The serdev_device_driver's probe() method should then be able to call
serdev_device_open() successfully, but because UPF_DEAD is still dead
serdev_device_open() will fail with -ENXIO in this scenario:
serdev_device_open()
ctrl->ops->open() /* this callback being ttyport_open() */
tty->ops->open() /* this callback being uart_open() */
tty_port_open()
port->ops->activate() /* this callback being uart_port_activate() */
Find bit UPF_DEAD is set in uport->flags and fail with errno -ENXIO.
Fix this be clearing UPF_DEAD before tty_port_register_device_attr_serdev()
note this only moves up the UPD_DEAD clearing a small bit, before:
tty_port_register_device_attr_serdev();
mutex_unlock(&tty_port.mutex);
uart_port.flags &= ~UPF_DEAD;
mutex_unlock(&port_mutex);
after:
uart_port.flags &= ~UPF_DEAD;
tty_port_register_device_attr_serdev();
mutex_unlock(&tty_port.mutex);
mutex_unlock(&port_mutex);
Reported-by: Weifeng Liu <weifeng.liu.z@gmail.com>
Closes: https://lore.kernel.org/platform-driver-x86/20240505130800.2546640-1-weifeng.liu.z@gmail.com/
Tested-by: Weifeng Liu <weifeng.liu.z@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240509141549.63704-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At the default TX trigger level of 2 in non-DMA mode (meaning that an
interrupt is generated when less than 2 characters are left in the
FIFO), we have observed frequent buffer underruns at 115200 Baud on an
i.MX8M Nano. This can cause communication issues if the receiving side
expects a continuous transfer.
Increasing the level to 8 makes the UART trigger an interrupt earlier,
giving the kernel enough time to refill the FIFO, at the cost of
triggering one interrupt per ~24 instead of ~30 bytes of transmitted
data (as the i.MX UART has a 32 byte FIFO).
Signed-off-by: Michael Krummsdorf <michael.krummsdorf@tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20240508133744.35858-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8250_pnp sets drvdata to line + 1 if the probe is successful. The users
of drvdata are in remove, suspend and resume callbacks, none of which
will be called if probe failed. The line acquired from drvdata can
never be zero in those functions and the checks for that can be
removed.
Eliminate also +/-1 step because all users of line subtract 1 from the
value.
These might have been leftover from legacy PM callbacks that could
be called without probe being successful.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240506121202.11253-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hrtimer for RXDMA timeout was unconditionally restarted in the RXDMA
complete handler ignoring the fact that setting up DMA may fail and PIO
is used instead. Explicitly stop the timer when DMA is completed and
only restart it when setting up DMA was successful. This makes the
intention of the timer much clearer, the driver easier to understand and
simplifies assumptions about the timer. The latter avoids race
conditions if these assumptions were not met or confused.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20240506114016.30498-9-wsa+renesas@sang-engineering.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_BASE_SMALL is currently a type int but is only used as a boolean.
So, change its type to bool and adapt all usages:
CONFIG_BASE_SMALL == 0 becomes !IS_ENABLED(CONFIG_BASE_SMALL) and
CONFIG_BASE_SMALL != 0 becomes IS_ENABLED(CONFIG_BASE_SMALL).
Reviewed-by: Petr Mladek <pmladek@suse.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Yoann Congal <yoann.congal@smile.fr>
Link: https://lore.kernel.org/r/20240505080343.1471198-3-yoann.congal@smile.fr
Signed-off-by: Petr Mladek <pmladek@suse.com>
... and use it to limit the virtual terminals to just N_TTY. They are
kind of special, and in particular, the "con_write()" routine violates
the "writes cannot sleep" rule that some ldiscs rely on.
This avoids the
BUG: sleeping function called from invalid context at kernel/printk/printk.c:2659
when N_GSM has been attached to a virtual console, and gsmld_write()
calls con_write() while holding a spinlock, and con_write() then tries
to get the console lock.
Tested-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Daniel Starke <daniel.starke@siemens.com>
Reported-by: syzbot <syzbot+dbac96d8e73b61aa559c@syzkaller.appspotmail.com>
Closes: https://syzkaller.appspot.com/bug?extid=dbac96d8e73b61aa559c
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lore.kernel.org/r/20240423163339.59780-1-torvalds@linux-foundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using a high speed clock with a low baud rate, the 4x prescaler is
automatically selected if required. In that case, sc16is7xx_set_baud()
properly configures the chip registers, but returns an incorrect baud
rate by not taking into account the prescaler value. This incorrect baud
rate is then fed to uart_update_timeout().
For example, with an input clock of 80MHz, and a selected baud rate of 50,
sc16is7xx_set_baud() will return 200 instead of 50.
Fix this by first changing the prescaler variable to hold the selected
prescaler value instead of the MCR bitfield. Then properly take into
account the selected prescaler value in the return value computation.
Also add better documentation about the divisor value computation.
Fixes: dfeae619d7 ("serial: sc16is7xx")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20240430200431.4102923-1-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a scenario when resuming from some power saving states
with no_console_suspend where console output can be generated
before the 8250_bcm7271 driver gets the opportunity to restore
the baud_mux_clk frequency. Since the baud_mux_clk is at its
default frequency at this time the output can be garbled until
the driver gets the opportunity to resume.
Since this is only an issue with console use of the serial port
during that window and the console isn't likely to use baud
rates that require alternate baud_mux_clk frequencies, allow the
driver to select the default_mux_rate if it is accurate enough.
Fixes: 41a469482d ("serial: 8250: Add new 8250-core based Broadcom STB driver")
Cc: stable@vger.kernel.org
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240424222559.1844045-1-opendmb@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When Rx in-band wakeup is enabled, set RTS to true in mtk8250_shutdown()
so the connected device can still send message and trigger IRQ when the
system is suspended.
Fixes: 18c9d4a3c2 ("serial: When UART is suspended, set RTS to false")
Cc: stable <stable@kernel.org>
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Link: https://lore.kernel.org/r/20240424130619.2924456-1-treapking@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current implementation uses either gsm0_receive() or gsm1_receive()
depending on whether the user configured the mux in basic or advanced
option mode. Both functions share some state values over the same logical
elements of the frame. However, both frame types differ in their nature.
gsm0_receive() uses non-transparency framing, whereas gsm1_receive() uses
transparency mechanism. Switching between both modes leaves the receive
function in an undefined state when done during frame reception.
Fix this by splitting both states. Add gsm0_receive_state_check_and_fix()
and gsm1_receive_state_check_and_fix() to ensure that gsm->state is reset
after a change of gsm->receive.
Note that gsm->state is only accessed in:
- gsm0_receive()
- gsm1_receive()
- gsm_error()
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20240424054842.7741-2-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Assuming the following:
- side A configures the n_gsm in basic option mode
- side B sends the header of a basic option mode frame with data length 1
- side A switches to advanced option mode
- side B sends 2 data bytes which exceeds gsm->len
Reason: gsm->len is not used in advanced option mode.
- side A switches to basic option mode
- side B keeps sending until gsm0_receive() writes past gsm->buf
Reason: Neither gsm->state nor gsm->len have been reset after
reconfiguration.
Fix this by changing gsm->count to gsm->len comparison from equal to less
than. Also add upper limit checks against the constant MAX_MRU in
gsm0_receive() and gsm1_receive() to harden against memory corruption of
gsm->len and gsm->mru.
All other checks remain as we still need to limit the data according to the
user configuration and actual payload size.
Reported-by: j51569436@gmail.com
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218708
Tested-by: j51569436@gmail.com
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20240424054842.7741-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case the UART port is used as a console, no_console_suspend is
available in bootargs and UART port is part of a software-controlled power
domain we need to call device_set_awake_path(). This lets the power
domain core code know that this domain should not be powered off
during system suspend. Otherwise, the UART port power domain is turned off,
nothing is printed while suspending and the suspend/resume process is
blocked. This was detected on the Renesas RZ/G3S SoC while adding support
for power domains.
Based on code investigation (on v6.9-rc5), this issue is present on other
SoCs (e.g., Renesas R-Mobile A1 [1], IMX8QXP [2]) and different SoCs have
particular implementation to handle it. Due to this the patch added the
call of device_set_awake_path() in uart_suspend_port() instead of having
it in the platform specific UART driver.
[1] drivers/pmdomain/renesas/rmobile-sysc.c:116
[2] drivers/pmdomain/imx/scu-pd.c:357
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Tony Lindgren <tony.lindgren@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20240430095930.2806067-1-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for an optional reset for the uartps controller using
the reset driver. If the uartps node contains the "resets" property,
then cdns_uart_startup performs uartps controller non-pulse out of reset
and reset in exit path.
Signed-off-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Link: https://lore.kernel.org/r/20240425062358.1347684-4-manikanta.guntupalli@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SIMPLE_DEV_PM_OPS() is deprecated, replace it with the
DEFINE_SIMPLE_DEV_PM_OPS() and use pm_sleep_ptr() for setting
the driver's PM routines.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20240422083237.207447-1-andy.shevchenko@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make type of bit parameter and returned one the same in exar_ee_*_bit().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Parker Newman <pnewman@connecttech.com>
Link: https://lore.kernel.org/r/20240503171917.2921250-13-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use BIT() in exar_ee_read() like other functions do.
While at it, explain the EEPROM type and the dummy bit requirement.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Parker Newman <pnewman@connecttech.com>
Link: https://lore.kernel.org/r/20240503171917.2921250-12-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to use dev_err_probe() to simplify the error path and
unify a message template.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Parker Newman <pnewman@connecttech.com>
Link: https://lore.kernel.org/r/20240503171917.2921250-11-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two similar switch-cases which use different style.
Unify them and one more to return from the cases directly.
While at it, add missing default in another switch-case.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Parker Newman <pnewman@connecttech.com>
Link: https://lore.kernel.org/r/20240503171917.2921250-10-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We may reuse ->setup() for the same purpose as it was done before.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Parker Newman <pnewman@connecttech.com>
Link: https://lore.kernel.org/r/20240503171917.2921250-8-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use PCI_SUBVENDOR_ID_IBM for subvendor ID instead of vendor one.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Parker Newman <pnewman@connecttech.com>
Link: https://lore.kernel.org/r/20240503171917.2921250-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kernel doc validator is not happy:
warning: Function parameter or struct member 'pcidev' not described in 'cti_get_port_type_xr17c15x_xr17v25x'
warning: Function parameter or struct member 'pcidev' not described in 'cti_get_port_type_fpga'
warning: Function parameter or struct member 'pcidev' not described in 'cti_get_port_type_xr17v35x'
Add missed descriptions.
Fixes: f7ce070629 ("serial: exar: add CTI specific setup code")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Parker Newman <pnewman@connecttech.com>
Link: https://lore.kernel.org/r/20240503171917.2921250-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PCI core may return positive codes for the specific errors.
There is a special API to convert them to negative stanrard ones.
Use that API to avoid returning positive values as error codes.
Fixes: f7ce070629 ("serial: exar: add CTI specific setup code")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Parker Newman <pnewman@connecttech.com>
Link: https://lore.kernel.org/r/20240503171917.2921250-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is one of the hackiest Alpha machines, and the only one without
PCI support. Removing this allows cleaning up code in eise and tty
drivers in addition to the architecture code.
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Acked-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Currently, when kdb is compiled with keyboard support, then we will use
schedule_work() to provoke reset of the keyboard status. Unfortunately
schedule_work() gets called from the kgdboc post-debug-exception
handler. That risks deadlock since schedule_work() is not NMI-safe and,
even on platforms where the NMI is not directly used for debugging, the
debug trap can have NMI-like behaviour depending on where breakpoints
are placed.
Fix this by using the irq work system, which is NMI-safe, to defer the
call to schedule_work() to a point when it is safe to call.
Reported-by: Liuye <liu.yeC@h3c.com>
Closes: https://lore.kernel.org/all/20240228025602.3087748-1-liu.yeC@h3c.com/
Cc: stable@vger.kernel.org
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240424-kgdboc_fix_schedule_work-v2-1-50f5a490aec5@linaro.org
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Use the macro PCI_IRQ_INTX instead of the deprecated PCI_IRQ_LEGACY macro.
Link: https://lore.kernel.org/r/20240325070944.3600338-7-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want the tty fixes in here as well, and it resolves a merge conflict
in:
drivers/tty/serial/serial_core.c
as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The -next commit f8fef2fa41 (tty: msm_serial: use
dmaengine_prep_slave_sg()), switched to using dma_map_sg(). But the
return value of dma_map_sg() is special: it returns number of elements
mapped. And not a standard error value.
The commit also forgot to reset dma->tx_sg in case of this failure.
Fix both these mistakes.
Thanks to Marek who helped debugging this.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20240419080931.30949-1-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-Fix several "missing identifier name" warnings from checkpatch in
struct exar8250_platform and struct exar8250_board.
Example:
WARNING: function definition argument <arg> should also have an
identifier name
- Fix space before tab warning from checkpatch:
WARNING: please, no space before tabs
+ * 0^I^I2 ^IMode bit 0$
Signed-off-by: Parker Newman <pnewman@connecttech.com>
Link: https://lore.kernel.org/r/f7fa6c16cb5f2c8c1c7cb7d29f80bc7be53f91ab.1713382717.git.pnewman@connecttech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a large patch but is only additions. All changes and removals
are made in previous patches in this series.
- Add CTI board_init and port setup functions for each UART type
- Add CTI_EXAR_DEVICE() and CTI_PCI_DEVICE() macros
- Add support for reading a word from the Exar EEPROM.
- Add support for configuring and setting a single MPIO
- Add various helper functions for CTI boards.
- Add osc_freq to struct exar8250
Signed-off-by: Parker Newman <pnewman@connecttech.com>
Link: https://lore.kernel.org/r/ae4a66e7342b686cb8d4b15317585dfb37222cf4.1713382717.git.pnewman@connecttech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add an optional "board_init()" function pointer to struct exar8250_board
which is called once during probe prior to setting up the ports. It will
be used in subsequent patches of this series.
Signed-off-by: Parker Newman <pnewman@connecttech.com>
Link: https://lore.kernel.org/r/0e72a3154114c733283ff273bc1e31456ee101f4.1713382717.git.pnewman@connecttech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Preparatory patch removing existing Connect Tech setup code and
CONNECT_DEVICE macro.
Subsequent patches in this series will add in new UART family specific
setup code and new device definition macros to allow for supporting CTI
serial cards with Exar PCI IDs and CTI PCI IDs.
Signed-off-by: Parker Newman <pnewman@connecttech.com>
Link: https://lore.kernel.org/r/06a04b6c683ca20c50646cc0836be869c2dacd87.1713382717.git.pnewman@connecttech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When an UART is opened that still has .throttled set from a previous
open, the RX interrupt is enabled but the irq handler doesn't consider
it. This easily results in a stuck irq with the effect to occupy the CPU
in a tight loop.
So reset the throttle state in .startup() to ensure that RX irqs are
handled.
Fixes: d1ec8a2eab ("serial: stm32: update throttle and unthrottle ops for dma mode")
Cc: stable@vger.kernel.org
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/a784f80d3414f7db723b2ec66efc56e1ad666cbf.1713344161.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If there is a stuck irq that the handler doesn't address, returning
IRQ_HANDLED unconditionally makes it impossible for the irq core to
detect the problem and disable the irq. So only return IRQ_HANDLED if
an event was handled.
A stuck irq is still problematic, but with this change at least it only
makes the UART nonfunctional instead of occupying the (usually only) CPU
by 100% and so stall the whole machine.
Fixes: 48a6092fb4 ("serial: stm32-usart: Add STM32 USART Driver")
Cc: stable@vger.kernel.org
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/5f92603d0dfd8a5b8014b2b10a902d91e0bb881f.1713344161.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 16550a serial port based on the ACPI table requires obtaining the
reg-shift attribute. In the ACPI scenario, If the reg-shift property
is not configured like in DTS, the 16550a serial driver cannot read or
write controller registers properly during initialization.
Signed-off-by: Guanbing Huang <albanhuang@tencent.com>
Suggested-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bing Fan <tombinfan@tencent.com>
Tested-by: Linheng Du <dylanlhdu@tencent.com>
Link: https://lore.kernel.org/r/4726ecea8f7bfbfe42501b4f6ad9fe5b38994574.1713234515.git.albanhuang@tencent.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function __uart_read_properties doesn't cover PNP devices, so add IRQ
processing for PNP devices in the branch.
Signed-off-by: Guanbing Huang <albanhuang@tencent.com>
Suggested-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bing Fan <tombinfan@tencent.com>
Tested-by: Linheng Du <dylanlhdu@tencent.com>
Link: https://lore.kernel.org/r/7f4ca31ef1cab4c6ecad22fafd82117686b696be.1713234515.git.albanhuang@tencent.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dw8250_serial_inq() uses unsigned int variable to store 8-bit value.
Due to that it needs a cast which can be avoided by switching to use
u8 instead of unsigned int.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240412173937.187442-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By waiting at most 1 second for USR2_TXDC to be set, we avoid a potential
deadlock.
In case of the timeout, there is not much we can do, so we simply ignore
the transmitter state and optimistically try to continue.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/919647898c337a46604edcabaf13d42d80c0915d.1712837613.git.esben@geanix.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After conversion to the kfifo, it becomes possible to extract two helper
functions for better maintenance and code deduplication. Do it here.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240409174057.1104262-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pengfei Xu reports, that the -next commit 1788cf6a91 (tty: serial:
switch from circ_buf to kfifo) tries to emit a WARNING and that leads to
lockdep errors. Obviously we cannot print anything from uart_put_char()!
This WARN_ON_ONCE() was/is a debug aid to check if the condition in
uart_put_char() can happen at all. Pengfei Xu confirmed it can. Unlike
me and kbuild bot in my queue.
Second, I completely forgot about it, so I did not remove it in the
final version, nor mentioned it in the commit log.
Drop it now as we are all good. And we even have stack traces (and a
reproducer)!
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Reported-by: Pengfei Xu <pengfei.xu@intel.com>
Link: https://lore.kernel.org/r/20240416071904.21440-1-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marek reports, that the -next commit 1788cf6a91 (tty: serial: switch
from circ_buf to kfifo) broke meson_uart and qcom_geni_serial. The
commit mistakenly advanced the kfifo twice: once by
uart_fifo_get()/kfifo_out() and second time by uart_xmit_advance().
To advance the fifo only once, drop the superfluous uart_xmit_advance()
from both.
To count the TX statistics properly, use uart_fifo_out() in
qcom_geni_serial (meson_uart_start_tx() already uses that).
I checked all other uses of uart_xmit_advance() and they appear correct:
either they are finishing DMA transfers or are after peek/linear_ptr
(i.e. they do not advance fifo).
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: 1788cf6a91 ("tty: serial: switch from circ_buf to kfifo")
Cc: Neil Armstrong <neil.armstrong@linaro.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20240416054825.6211-1-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When terminal is unresponsive, one cannot use dmesg to view
the printk ring buffer messages. Also, syslog services may be
disabled, especially on embedded systems, to check the messages
after a reboot. In this scenario, replay the messages in printk
ring buffer on consoles via sysrq by pressing sysrq+R.
The console loglevel will determine which all kernel log messages
are displayed. The messages will be displayed only when
console_trylock() succeeds. Users could repeat the sysrq key when
it fails. If the owner of console subsystem lock is stuck,
repeating the key won't work.
Suggested-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Shimoyashiki Taichi <taichi.shimoyashiki@sony.com>
Reviewed-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sreenath Vijayan <sreenath.vijayan@sony.com>
Link: https://lore.kernel.org/r/cc3b9b1aae60a236c6aed1dc7b0ffa2c7cd1f183.1710220326.git.sreenath.vijayan@sony.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are seeing start_tx being called after port shutdown as noted by Jiri.
This happens because we are missing the startup and shutdown related
functions for the serial base port.
Let's fix the issue by adding startup and shutdown functions for the
serial base port to block tx flushing for the serial base port when the
port is not in use.
Fixes: 84a9582fd2 ("serial: core: Start managing serial controllers to enable runtime PM")
Cc: stable <stable@kernel.org>
Reported-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20240411055848.38190-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As Jiri rightfully pointed out the current to_max3100_port() macro
implementation is fragile in a sense that it expects the variable
name to be port, otherwise it blow up the build.
Change this to be static inline to prevent bad compilation.
Suggested-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240410141135.1378948-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable tmout is being assigned a value that is never read, it is
being re-assinged in the following for-loop statement. The assignment
is redundant and can be removed.
Cleans up clang scan warning:
drivers/tty/serial/omap-serial.c:1096:3: warning: Value stored to 'tmout'
is never read [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20240411085537.306020-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to inline serial_base_add_isa_preferred_console() based on
CONFIG_SERIAL_8250_CONSOLE and not based on CONFIG_SERIAL_CORE_CONSOLE.
Otherwise we can get the follwoing error as noted by Stephen:
ERROR: modpost: "serial_base_add_isa_preferred_console"
[drivers/tty/serial/8250/8250.ko] undefined!
We also have a duplicate inlined serial_base_add_isa_preferred_console(),
in serial_base_bus.c added by the same commit by accident, let's drop it.
Fixes: a8b04cfe7d ("serial: 8250: Add preferred console in serial8250_isa_init_ports()")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20240411080622.11929-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since each I2C/SPI probe function can modify sc16is7xx_regcfg at the same
time, change structure to be constant and do the required modifications on
a local copy.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://lore.kernel.org/r/20240409154253.3043822-6-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before, sc16is7xx_lines was checked for a free (zero) bit first, and then
later it was set only if UART port registration succeeded. Now that
sc16is7xx_lines is shared for the I2C and SPI drivers, there is a
possibility that the two drivers can simultaneously try to reserve the same
line bit at the same time.
To prevent this, make sure line allocation is reserved atomically, and use
a new variable to hold the status of UART port registration.
Now that we no longer need to search if a bit is set, it is now possible
to simplify sc16is7xx_lines allocation by using the IDA framework.
Link: https://lore.kernel.org/all/20231212150302.a9ec5d085a4ba65e89ca41af@hugovil.com/
Link: https://lore.kernel.org/all/CAHp75VebCZckUrNraYQj9k=Mrn2kbYs1Lx26f5-8rKJ3RXeh-w@mail.gmail.com/
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240409154253.3043822-5-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Split the common code from sc16is7xx driver and move the I2C and SPI bus
parts into interface-specific source files.
sc16is7xx becomes the core functions which can support multiple bus
interfaces like I2C and SPI.
No functional changes intended.
Also simplify and improve Kconfig entries.
- Capitalize SPI keyword for consistency
- Display list of supported ICs each on a separate line (and aligned) to
facilitate locating a specific IC model
- Add Manufacturer name at start of description string
- Add UART keyword to description string
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240409154253.3043822-4-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to check for previous port registration in
sc16is7xx_remove() because if sc16is7xx_probe() succeeded, we are
guaranteed to have successfully registered both ports. We can thus
unconditionally clear the line allocation bit in sc16is7xx_lines.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://lore.kernel.org/r/20240409154253.3043822-3-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace incorrect include with the proper one for sched_set_fifo()
declaration.
Fixes: 28d2f209cd ("sched,serial: Convert to sched_set_fifo()")
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240409154253.3043822-2-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case that no RTS GPIO is available do not use a dedicated nullified
serial_rs485 struct to disable RS485 support, but simply delete the
SER_RS485_ENABLED flag in the ports rs485_supported struct.
This make the structure superfluous and it can be removed.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20240407002709.16224-5-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The serial core already checks the RS485 RTS settings for sanity, so remove
the superfluous check in serial8250_em485_config().
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20240407002709.16224-4-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable dmacr is only used if DMA is enabled, so move it into the
CONFIG_DMA_ENGINE conditional.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20240407002709.16224-3-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to earlier code changes function pl011_get_rs485_mode() is now merely
a wrapper for uart_get_rs485_mode() which does not add any further
functionality. So remove it and instead call uart_get_rs485_mode()
directly.
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20240407002709.16224-2-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of using container_of() explicitly, introduce a helper macro.
This saves a lot of lines of code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240409144721.638326-8-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SIMPLE_DEV_PM_OPS() is deprecated, replace it with the
DEFINE_SIMPLE_DEV_PM_OPS() and use pm_sleep_ptr() for setting
the driver's PM routines.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240409144721.638326-7-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MODULE_ALIAS() in most cases is a pure hack to avoid placing ID tables.
Replace it with the respective ID tables.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240409144721.638326-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The struct uart_port has a copy of the IRQ that is also stored
in the private data structure. Remove the duplication in the latter
one.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240409144721.638326-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The circular buffer is NULLified in uart_tty_port_shutdown()
under the spin lock. However, the PM or other timer based callbacks
may still trigger after this event without knowning that buffer pointer
is not valid. Since the serial code is a bit inconsistent in checking
the buffer state (some rely on the head-tail positions, some on the
buffer pointer), it's better to have both aligned, i.e. buffer pointer
to be NULL and head-tail possitions to be the same, meaning it's empty.
This will prevent asynchronous calls to dereference NULL pointer as
reported recently in 8250 case:
BUG: kernel NULL pointer dereference, address: 00000cf5
Workqueue: pm pm_runtime_work
EIP: serial8250_tx_chars (drivers/tty/serial/8250/8250_port.c:1809)
...
? serial8250_tx_chars (drivers/tty/serial/8250/8250_port.c:1809)
__start_tx (drivers/tty/serial/8250/8250_port.c:1551)
serial8250_start_tx (drivers/tty/serial/8250/8250_port.c:1654)
serial_port_runtime_suspend (include/linux/serial_core.h:667 drivers/tty/serial/serial_port.c:63)
__rpm_callback (drivers/base/power/runtime.c:393)
? serial_port_remove (drivers/tty/serial/serial_port.c:50)
rpm_suspend (drivers/base/power/runtime.c:447)
The proposed change will prevent ->start_tx() to be called during
suspend on shut down port.
Fixes: 43066e3222 ("serial: port: Don't suspend if the port is still busy")
Cc: stable <stable@kernel.org>
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202404031607.2e92eebe-lkp@intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240404150034.41648-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Signed-off-by: wangkaiyuan <wangkaiyuan@inspur.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240318064216.1765-1-wangkaiyuan@inspur.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Signed-off-by: wangkaiyuan <wangkaiyuan@inspur.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20240318064036.1656-1-wangkaiyuan@inspur.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mitigation was intended to stop the irq completely. That may be
better than a hard lock-up but it turns out that you get a crash anyway
if you're using pmac_zilog as a serial console:
ttyPZ0: pmz: rx irq flood !
BUG: spinlock recursion on CPU#0, swapper/0
That's because the pr_err() call in pmz_receive_chars() results in
pmz_console_write() attempting to lock a spinlock already locked in
pmz_interrupt(). With CONFIG_DEBUG_SPINLOCK=y, this produces a fatal
BUG splat. The spinlock in question is the one in struct uart_port.
Even when it's not fatal, the serial port rx function ceases to work.
Also, the iteration limit doesn't play nicely with QEMU, as can be
seen in the bug report linked below.
A web search for other reports of the error message "pmz: rx irq flood"
didn't produce anything. So I don't think this code is needed any more.
Remove it.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Aneesh Kumar K.V <aneesh.kumar@kernel.org>
Cc: Naveen N. Rao <naveen.n.rao@linux.ibm.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: stable@kernel.org
Cc: linux-m68k@lists.linux-m68k.org
Link: https://github.com/vivier/qemu-m68k/issues/44
Link: https://lore.kernel.org/all/1078874617.9746.36.camel@gaston/
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@kernel.org>
Signed-off-by: Finn Thain <fthain@linux-m68k.org>
Link: https://lore.kernel.org/r/e853cf2c762f23101cd2ddec0cc0c2be0e72685f.1712568223.git.fthain@linux-m68k.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver complains that PCI IDs are not needed for some of the LAVA cards:
[ 0.297252] serial 0000:04:00.0: Redundant entry in serial pci_table.
[ 0.297252] Please send the output of lspci -vv, this
[ 0.297252] message (0x1407,0x0120,0x0000,0x0000), the
[ 0.297252] manufacturer and name of serial board or
[ 0.297252] modem board to <linux-serial@vger.kernel.org>.
Do as suggested.
Reported-by: Jimmy A <jimand04@hotmail.com>
Closes: https://lore.kernel.org/r/VI1P194MB052751BE157EFE9CEAB75725CE362@VI1P194MB0527.EURP194.PROD.OUTLOOK.COM
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20240403224152.945099-1-andy.shevchenko@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 45a3a8ef81 ("serial: core: Revert checks for tx runtime PM state")
caused a regression for Sun Ultra 60 for the sunsab driver as reported by
Nick Bowler <nbowler@draconx.ca>.
We need to add back the check runtime PM enabled state for serial port
controller device, I wrongly assumed earlier we could just remove it.
Fixes: 45a3a8ef81 ("serial: core: Revert checks for tx runtime PM state")
Cc: stable <stable@kernel.org>
Reported-by: Nick Bowler <nbowler@draconx.ca>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20240325071649.27040-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The uart_handle_cts_change() function in serial_core expects the caller
to hold uport->lock. For example, I have seen the below kernel splat,
when the Bluetooth driver is loaded on an i.MX28 board.
[ 85.119255] ------------[ cut here ]------------
[ 85.124413] WARNING: CPU: 0 PID: 27 at /drivers/tty/serial/serial_core.c:3453 uart_handle_cts_change+0xb4/0xec
[ 85.134694] Modules linked in: hci_uart bluetooth ecdh_generic ecc wlcore_sdio configfs
[ 85.143314] CPU: 0 PID: 27 Comm: kworker/u3:0 Not tainted 6.6.3-00021-gd62a2f068f92 #1
[ 85.151396] Hardware name: Freescale MXS (Device Tree)
[ 85.156679] Workqueue: hci0 hci_power_on [bluetooth]
(...)
[ 85.191765] uart_handle_cts_change from mxs_auart_irq_handle+0x380/0x3f4
[ 85.198787] mxs_auart_irq_handle from __handle_irq_event_percpu+0x88/0x210
(...)
Cc: stable@vger.kernel.org
Fixes: 4d90bb147e ("serial: core: Document and assert lock requirements for irq helpers")
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Emil Kronborg <emil.kronborg@protonmail.com>
Link: https://lore.kernel.org/r/20240320121530.11348-1-emil.kronborg@protonmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e5d6bd25f9 ("serial: 8250_dw: Do not reclock if already at
correct rate") breaks the dw UARTs on Intel Bay Trail (BYT) and
Cherry Trail (CHT) SoCs.
Before this change the RTL8732BS Bluetooth HCI which is found
connected over the dw UART on both BYT and CHT boards works properly:
Bluetooth: hci0: RTL: examining hci_ver=06 hci_rev=000b lmp_ver=06 lmp_subver=8723
Bluetooth: hci0: RTL: rom_version status=0 version=1
Bluetooth: hci0: RTL: loading rtl_bt/rtl8723bs_fw.bin
Bluetooth: hci0: RTL: loading rtl_bt/rtl8723bs_config-OBDA8723.bin
Bluetooth: hci0: RTL: cfg_sz 64, total sz 24508
Bluetooth: hci0: RTL: fw version 0x365d462e
where as after this change probing it fails:
Bluetooth: hci0: RTL: examining hci_ver=06 hci_rev=000b lmp_ver=06 lmp_subver=8723
Bluetooth: hci0: RTL: rom_version status=0 version=1
Bluetooth: hci0: RTL: loading rtl_bt/rtl8723bs_fw.bin
Bluetooth: hci0: RTL: loading rtl_bt/rtl8723bs_config-OBDA8723.bin
Bluetooth: hci0: RTL: cfg_sz 64, total sz 24508
Bluetooth: hci0: command 0xfc20 tx timeout
Bluetooth: hci0: RTL: download fw command failed (-110)
Revert the changes to fix this regression.
Fixes: e5d6bd25f9 ("serial: 8250_dw: Do not reclock if already at correct rate")
Cc: stable@vger.kernel.org
Cc: Peter Collingbourne <pcc@google.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Peter Collingbourne <pcc@google.com>
Link: https://lore.kernel.org/r/20240317214123.34482-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Goto the clean up path to clean up a couple clocks before returning
on this error path.
Fixes: 0087b9e694 ("serial: 8250_lpc18xx: Switch to use uart_read_port_properties()")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/92646c10-e0b5-4117-a9ac-ce9987d33ce3@moroto.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no code using max3100_work() before the definition of it.
Remove unneeded forward declaration.
While at it, move max3100_dowork() and max3100_timeout() down in
the code to be after actual max3100_work() implementation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240402195306.269276-15-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While there is no user of this callback in the kernel, it also breaks
the relationship in the driver model. The correct implementation should
be done via GPIO or regulator framework.
Remove custom HW shutdown support for good and, if needed, we will
implement it correctly later on.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240402195306.269276-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no user of the struct plat_max3100 outside the driver.
Inline its contents into the driver. While at it, drop outdated
example in the comment.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240402195306.269276-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sparse is not happy about misuse of bitwise types:
.../max3100.c:194:13: warning: incorrect type in assignment (different base types)
.../max3100.c:194:13: expected unsigned short [addressable] [usertype] etx
.../max3100.c:194:13: got restricted __be16 [usertype]
.../max3100.c:202:15: warning: cast to restricted __be16
Fix this by choosing proper types for the respective variables.
Fixes: 7831d56b0a ("tty: MAX3100")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240402195306.269276-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The removal of the last MAX3100 device triggers the removal of
the driver. However, code doesn't update the respective global
variable and after insmod — rmmod — insmod cycle the kernel
oopses:
max3100 spi-PRP0001:01: max3100_probe: adding port 0
BUG: kernel NULL pointer dereference, address: 0000000000000408
...
RIP: 0010:serial_core_register_port+0xa0/0x840
...
max3100_probe+0x1b6/0x280 [max3100]
spi_probe+0x8d/0xb0
Update the actual state so next time UART driver will be registered
again.
Hugo also noticed, that the error path in the probe also affected
by having the variable set, and not cleared. Instead of clearing it
move the assignment after the successfull uart_register_driver() call.
Fixes: 7831d56b0a ("tty: MAX3100")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240402195306.269276-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_handle_cts_change() has to be called with port lock taken,
Since we run it in a separate work, the lock may not be taken at
the time of running. Make sure that it's taken by explicitly doing
that. Without it we got a splat:
WARNING: CPU: 0 PID: 10 at drivers/tty/serial/serial_core.c:3491 uart_handle_cts_change+0xa6/0xb0
...
Workqueue: max3100-0 max3100_work [max3100]
RIP: 0010:uart_handle_cts_change+0xa6/0xb0
...
max3100_handlerx+0xc5/0x110 [max3100]
max3100_work+0x12a/0x340 [max3100]
Fixes: 7831d56b0a ("tty: MAX3100")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240402195306.269276-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UART's input clock rate can change at runtime but this is not
handled by the driver.
Add a clock_notifier callback that updates the divisors when the input
clock is updated. The serial8250_update_uartclk() is used to do so.
PRE_RATE_CHANGE and ABORT_RATE_CHANGE notifications are ignored, only
the POST_RATE_CHANGE is used. Not using PRE_RATE_CHANGE notification can
result in a few corrupted bytes during frequency transitions but, IMHO,
it can be acceptable in many use cases.
It has been tested on a DAVINCI/OMAP-L138 processor.
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Reviewed-by: Herve Codina <herve.codina@bootlin.com>
Link: https://lore.kernel.org/r/20240405120552.35991-1-bastien.curutchet@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are considerations to drop platform_driver_probe() as a concept
that isn't relevant any more today. It comes with an added complexity
that makes many users hold it wrong. (E.g. this driver should have
marked the driver struct with __refdata to prevent the below mentioned
false positive section mismatch warning.)
This fixes a W=1 build warning:
WARNING: modpost: drivers/tty/serial/pmac_zilog: section mismatch in reference: pmz_driver+0x8 (section: .data) -> pmz_detach (section: .exit.text)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/5ea3174616abc9fa256f115b4fb175d289ac1754.1711748999.git.u.kleine-koenig@pengutronix.de
Tested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As described in the added code comment, a reference to .exit.text is ok
for drivers registered via module_platform_driver_probe(). Make this
explicit to prevent the following section mismatch warning
WARNING: modpost: drivers/tty/amiserial: section mismatch in reference: amiga_serial_driver+0x8 (section: .data) -> amiga_serial_remove (section: .exit.text)
that triggers on an allmodconfig W=1 build.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/043afcbc94ad90079301f3c7738136a7993a1748.1711748999.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This change strips $abs_srctree of the input file containing the
character mapping table in the generated output. The motivation for this
change is Yocto emitting a build warning
WARNING: linux-lxatac-6.7-r0 do_package_qa: QA Issue: File /usr/src/debug/linux-lxatac/6.7-r0/drivers/tty/vt/consolemap_deftbl.c in package linux-lxatac-src contains reference to TMPDIR
So this change brings us one step closer to make the build result
reproducible independent of the build path.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20240311113017.483101-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver is using "sifive,fu540-c000-uart0" as a binding. The device
tree and documentation states "sifive,fu540-c000-uart" instead. This
means the binding is not matched and not used.
This did not cause any problems because the alternative binding, used in
the device tree, "sifive,uart0" is not handling the hardware any
different.
Align the binding in the driver with the documentation.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240307090950.eLELkuyK@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_gpio.h is deprecated and subject to remove.
The driver doesn't use it directly, replace it
with what is really being used.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240307114243.3642832-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare 8250 ISA ports to drop kernel command line serial console
handling from console_setup().
We need to set the preferred console in serial8250_isa_init_ports()
to drop a dependency to setup_console() handling the ttyS related
quirks. Otherwise when console_setup() handles the ttyS related
options, console gets enabled only at driver probe time.
Note that this mostly affects x86 as this happens based on define
SERIAL_PORT_DFNS.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20240327110021.59793-7-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to start moving the serial console quirks out of console_setup(),
let's add parsing for the quirks to the serial core layer. We can use
serial_base_add_one_prefcon() to handle the quirks.
Note that eventually we may want to set up driver specific console quirk
handling for the serial port device drivers to use. But we need to figure
out which driver(s) need to call the quirk. So for now, we just handle the
sparc quirk directly.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20240327110021.59793-6-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can now add hardware based addressing for serial ports. Starting with
commit 84a9582fd2 ("serial: core: Start managing serial controllers to
enable runtime PM"), and all the related fixes to this commit, the serial
core now knows to which serial port controller the ports are connected.
The serial ports can be addressed with DEVNAME:0.0 style naming. The names
are something like 00:04:0.0 for a serial port on qemu, and something like
2800000.serial:0.0 on platform device using systems like ARM64 for example.
The DEVNAME is the unique serial port hardware controller device name, AKA
the name for port->dev. The 0.0 are the serial core controller id and port
id.
Typically 0.0 are used for each controller and port instance unless the
serial port hardware controller has multiple controllers or ports.
Using DEVNAME:0.0 style naming actually solves two long term issues for
addressing the serial ports:
1. According to Andy Shevchenko, using DEVNAME:0.0 style naming fixes an
issue where depending on the BIOS settings, the kernel serial port ttyS
instance number may change if HSUART is enabled
2. Device tree using architectures no longer necessarily need to specify
aliases to find a specific serial port, and we can just allocate the
ttyS instance numbers dynamically in whatever probe order
To do this, let's match the hardware addressing style console name to
the character device name used, and add a preferred console using the
character device name.
Note that when using console=DEVNAME:0.0 style kernel command line, the
8250 serial console gets enabled later compared to using console=ttyS
naming for ISA ports. This is because the serial port DEVNAME to character
device mapping is not known until the serial driver probe time. If used
together with earlycon, this issue is avoided.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20240327110021.59793-5-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dma_map_single() provides much easier interface for simple mappings as
used for RX in atmel_serial. So switch to that, removing all the s-g
unnecessary handling.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Cc: linux-arm-kernel@lists.infradead.org
Link: https://lore.kernel.org/r/20240405060826.2521-16-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is repeated in the code and there is also a big warning by
ATMEL_SERIAL_RINGSIZE. So define ATMEL_SERIAL_RX_SIZE and use it
appropriatelly.
The macro uses array_size() and kmalloc_array() is switched to
kmalloc().
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Cc: linux-arm-kernel@lists.infradead.org
Link: https://lore.kernel.org/r/20240405060826.2521-15-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dma_map_single() provides much easier interface for simple mappings as
used for TX in atmel_serial. So switch to that, removing all the s-g
unnecessary handling.
Note that it is not easy (maybe impossible) to use kfifo_dma_* API for
atmel's serial purposes. It handles DMA very specially.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Cc: linux-arm-kernel@lists.infradead.org
Link: https://lore.kernel.org/r/20240405060826.2521-14-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch from struct circ_buf to proper kfifo. kfifo provides much better
API, esp. when wrap-around of the buffer needs to be taken into account.
Look at pl011_dma_tx_refill() or cpm_uart_tx_pump() changes for example.
Kfifo API can also fill in scatter-gather DMA structures, so it easier
for that use case too. Look at lpuart_dma_tx() for example. Note that
not all drivers can be converted to that (like atmel_serial), they
handle DMA specially.
Note that usb-serial uses kfifo for TX for ages.
omap needed a bit more care as it needs to put a char into FIFO to start
the DMA transfer when OMAP_DMA_TX_KICK is set. In that case, we have to
do kfifo_dma_out_prepare twice: once to find out the tx_size (to find
out if it is worths to do DMA at all -- size >= 4), the second time for
the actual transfer.
All traces of circ_buf are removed from serial_core.h (and its struct
uart_state).
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: Al Cooper <alcooperx@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>
Cc: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Vineet Gupta <vgupta@kernel.org>
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Maciej W. Rozycki <macro@orcam.me.uk>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Neil Armstrong <neil.armstrong@linaro.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Taichi Sugaya <sugaya.taichi@socionext.com>
Cc: Takao Orito <orito.takao@socionext.com>
Cc: Bjorn Andersson <andersson@kernel.org>
Cc: Konrad Dybcio <konrad.dybcio@linaro.org>
Cc: Pali Rohár <pali@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Aneesh Kumar K.V <aneesh.kumar@kernel.org>
Cc: Naveen N. Rao <naveen.n.rao@linux.ibm.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Orson Zhai <orsonzhai@gmail.com>
Cc: Baolin Wang <baolin.wang@linux.alibaba.com>
Cc: Chunyan Zhang <zhang.lyra@gmail.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Hammer Hsieh <hammerh0314@gmail.com>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Timur Tabi <timur@kernel.org>
Cc: Michal Simek <michal.simek@amd.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Christian König <christian.koenig@amd.com>
Link: https://lore.kernel.org/r/20240405060826.2521-13-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a preparatory for the serial-to-kfifo switch. kfifo understands
only scatter-gatter approach, so switch to that.
No functional change intended, it's just dmaengine_prep_slave_single()
inline expanded.
And in this case, switch from dma_map_single() to dma_map_sg() too. This
needs struct msm_dma changes. I split the rx and tx parts into an union.
TX is now struct scatterlist, RX remains the old good phys-virt-count
triple.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: Bjorn Andersson <andersson@kernel.org>
Cc: Konrad Dybcio <konrad.dybcio@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Link: https://lore.kernel.org/r/20240405060826.2521-12-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a preparatory for the serial-to-kfifo switch. kfifo understands
only scatter-gatter approach, so switch to that.
No functional change intended, it's just dmaengine_prep_slave_single()
inline expanded.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20240405060826.2521-11-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a preparatory for the serial-to-kfifo switch. kfifo understands
only scatter-gatter approach, so switch to that.
No functional change intended, it's just dmaengine_prep_slave_single()
inline expanded.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20240405060826.2521-10-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of TTY/Serial driver updates and cleanups for
6.9-rc1. Included in here are:
- more tty cleanups from Jiri
- loads of 8250 driver cleanups from Andy
- max310x driver updates
- samsung serial driver updates
- uart_prepare_sysrq_char() updates for many drivers
- platform driver remove callback void cleanups
- stm32 driver updates
- other small tty/serial driver updates
All of these have been in linux-next for a long time with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZfwqow8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynNegCffxTbsnbMGjWhVrQ326IJx/DFvNMAoI9csigv
m+G3RzefzZLRx8nAma0c
=GMfc
-----END PGP SIGNATURE-----
Merge tag 'tty-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the big set of TTY/Serial driver updates and cleanups for
6.9-rc1. Included in here are:
- more tty cleanups from Jiri
- loads of 8250 driver cleanups from Andy
- max310x driver updates
- samsung serial driver updates
- uart_prepare_sysrq_char() updates for many drivers
- platform driver remove callback void cleanups
- stm32 driver updates
- other small tty/serial driver updates
All of these have been in linux-next for a long time with no reported
issues"
* tag 'tty-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (199 commits)
dt-bindings: serial: stm32: add power-domains property
serial: 8250_dw: Replace ACPI device check by a quirk
serial: Lock console when calling into driver before registration
serial: 8250_uniphier: Switch to use uart_read_port_properties()
serial: 8250_tegra: Switch to use uart_read_port_properties()
serial: 8250_pxa: Switch to use uart_read_port_properties()
serial: 8250_omap: Switch to use uart_read_port_properties()
serial: 8250_of: Switch to use uart_read_port_properties()
serial: 8250_lpc18xx: Switch to use uart_read_port_properties()
serial: 8250_ingenic: Switch to use uart_read_port_properties()
serial: 8250_dw: Switch to use uart_read_port_properties()
serial: 8250_bcm7271: Switch to use uart_read_port_properties()
serial: 8250_bcm2835aux: Switch to use uart_read_port_properties()
serial: 8250_aspeed_vuart: Switch to use uart_read_port_properties()
serial: port: Introduce a common helper to read properties
serial: core: Add UPIO_UNKNOWN constant for unknown port type
serial: core: Move struct uart_port::quirks closer to possible values
serial: sh-sci: Call sci_serial_{in,out}() directly
serial: core: only stop transmit when HW fifo is empty
serial: pch: Use uart_prepare_sysrq_char().
...
- Add AT_HWCAP3 and AT_HWCAP4 aux vector entries for future use by glibc.
- Add support for recognising the Power11 architected and raw PVRs.
- Add support for nr_cpus=n on the command line where the boot CPU is >= n.
- Add ppcxx_allmodconfig targets for all 32-bit sub-arches.
- Other small features, cleanups and fixes.
Thanks to: Akanksha J N, Brian King, Christophe Leroy, Dawei Li, Geoff Levand,
Greg Kroah-Hartman, Jan-Benedict Glaw, Kajol Jain, Kunwu Chan, Li zeming,
Madhavan Srinivasan, Masahiro Yamada, Nathan Chancellor, Nicholas Piggin, Peter
Bergner, Qiheng Lin, Randy Dunlap, Ricardo B. Marliere, Rob Herring, Sathvika
Vasireddy, Shrikanth Hegde, Uwe Kleine-König, Vaibhav Jain, Wen Xiong.
-----BEGIN PGP SIGNATURE-----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=K9Ok
-----END PGP SIGNATURE-----
Merge tag 'powerpc-6.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- Add AT_HWCAP3 and AT_HWCAP4 aux vector entries for future use
by glibc
- Add support for recognising the Power11 architected and raw PVRs
- Add support for nr_cpus=n on the command line where the
boot CPU is >= n
- Add ppcxx_allmodconfig targets for all 32-bit sub-arches
- Other small features, cleanups and fixes
Thanks to Akanksha J N, Brian King, Christophe Leroy, Dawei Li, Geoff
Levand, Greg Kroah-Hartman, Jan-Benedict Glaw, Kajol Jain, Kunwu Chan,
Li zeming, Madhavan Srinivasan, Masahiro Yamada, Nathan Chancellor,
Nicholas Piggin, Peter Bergner, Qiheng Lin, Randy Dunlap, Ricardo B.
Marliere, Rob Herring, Sathvika Vasireddy, Shrikanth Hegde, Uwe
Kleine-König, Vaibhav Jain, and Wen Xiong.
* tag 'powerpc-6.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (71 commits)
powerpc/macio: Make remove callback of macio driver void returned
powerpc/83xx: Fix build failure with FPU=n
powerpc/64s: Fix get_hugepd_cache_index() build failure
powerpc/4xx: Fix warp_gpio_leds build failure
powerpc/amigaone: Make several functions static
powerpc/embedded6xx: Fix no previous prototype for avr_uart_send() etc.
macintosh/adb: make adb_dev_class constant
powerpc: xor_vmx: Add '-mhard-float' to CFLAGS
powerpc/fsl: Fix mfpmr() asm constraint error
powerpc: Remove cpu-as-y completely
powerpc/fsl: Modernise mt/mfpmr
powerpc/fsl: Fix mfpmr build errors with newer binutils
powerpc/64s: Use .machine power4 around dcbt
powerpc/64s: Move dcbt/dcbtst sequence into a macro
powerpc/mm: Code cleanup for __hash_page_thp
powerpc/hv-gpci: Fix the H_GET_PERF_COUNTER_INFO hcall return value checks
powerpc/irq: Allow softirq to hardirq stack transition
powerpc: Stop using of_root
powerpc/machdep: Define 'compatibles' property in ppc_md and use it
of: Reimplement of_machine_is_compatible() using of_machine_compatible_match()
...
- unified GPR/CP0 regs handling for uasm
- cleanups and fixes
-----BEGIN PGP SIGNATURE-----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=M7G5
-----END PGP SIGNATURE-----
Merge tag 'mips_6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Thomas Bogendoerfer:
- added support for Mobileye SoCs
- unified GPR/CP0 regs handling for uasm
- cleanups and fixes
* tag 'mips_6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (56 commits)
mips: cm: Convert __mips_cm_phys_base() to weak function
mips: cm: Convert __mips_cm_l2sync_phys_base() to weak function
mips: dts: ralink: mt7621: add cell count properties to usb
mips: dts: ralink: mt7621: add serial1 and serial2 nodes
mips: dts: ralink: mt7621: reorder serial0 properties
mips: dts: ralink: mt7621: associate uart1_pins with serial0
MIPS: ralink: Don't use "proxy" headers
mips: sibyte: make tb_class constant
mips: mt: make mt_class constant
MIPS: ralink: Remove unused of_gpio.h
bus: bt1-apb: Remove duplicate include
MAINTAINERS: remove entry to non-existing file in MOBILEYE MIPS SOCS
MIPS: mipsregs: Parse fp and sp register by name in parse_r
tty: mips_ejtag_fdc: Fix passing incompatible pointer type warning
mips: zboot: Fix "no previous prototype" build warning
MIPS: mipsregs: Set proper ISA level for virt extensions
MIPS: Implement microMIPS MT ASE helpers
MIPS: Limit MIPS_MT_SMP support by ISA reversion
MIPS: Loongson64: test for -march=loongson3a cflag
MIPS: BMIPS: Drop unnecessary assembler flag
...
Commit fc7a6209d5 ("bus: Make remove callback return void") forces
bus_type::remove be void-returned, it doesn't make much sense for any
bus based driver implementing remove callbalk to return non-void to
its caller.
This change is for macio bus based drivers.
Signed-off-by: Dawei Li <set_pte_at@outlook.com>
Acked-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/TYCP286MB232391520CB471E7C8D6EA84CAD19@TYCP286MB2323.JPNP286.PROD.OUTLOOK.COM
This reverts commit 5c7e105cd1.
As identified by KASAN, the simplification done by the cleanup patch
was not legal.
>From tracing through the code, it can be seen that we're transmitting
from a 4096-byte circular buffer. We copy anywhere from 1-4 bytes from
it each time. The simplification runs into trouble when we get near
the end of the circular buffer. For instance, we might start out with
xmit->tail = 4094 and we want to transfer 4 bytes. With the code
before simplification this was no problem. We'd read buf[4094],
buf[4095], buf[0], and buf[1]. With the new code we'll do a
memcpy(&buf[4094], 4) which reads 2 bytes past the end of the buffer
and then skips transmitting what's at buf[0] and buf[1].
KASAN isn't 100% consistent at reporting this for me, but to be extra
confident in the analysis, I added traces of the tail and tx_bytes and
then wrote a test program:
while true; do
echo -n "abcdefghijklmnopqrstuvwxyz0" > /dev/ttyMSM0
sleep .1
done
I watched the traces over SSH and saw:
qcom_geni_serial_send_chunk_fifo: 4093 4
qcom_geni_serial_send_chunk_fifo: 1 3
Which indicated that one byte should be missing. Sure enough the
output that should have been:
abcdefghijklmnopqrstuvwxyz0
In one case was actually missing a byte:
abcdefghijklmnopqrstuvwyz0
Running "ls -al" on large directories also made the missing bytes
obvious since columns didn't line up.
While the original code may not be the most elegant, we only talking
about copying up to 4 bytes here. Let's just go back to the code that
worked.
Fixes: 5c7e105cd1 ("tty: serial: simplify qcom_geni_serial_send_chunk_fifo()")
Cc: stable <stable@kernel.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240304174952.1.I920a314049b345efd1f69d708e7f74d2213d0b49@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the remote uart device is not connected or not enabled after booting
up, the CTS line is high by default. At this time, if we enable the flow
control when opening the device(for example, using “stty -F /dev/ttyLP4
crtscts” command), there will be a pending idle preamble(first writing 0
and then writing 1 to UARTCTRL_TE will queue an idle preamble) that
cannot be sent out, resulting in the uart port fail to close(waiting for
TX empty), so the user space stty will have to wait for a long time or
forever.
This is an LPUART IP bug(idle preamble has higher priority than CTS),
here add a workaround patch to enable TX CTS after enabling UARTCTRL_TE,
so that the idle preamble does not get stuck due to CTS is deasserted.
Fixes: 380c966c09 ("tty: serial: fsl_lpuart: add 32-bit register interface support")
Cc: stable <stable@kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Link: https://lore.kernel.org/r/20240305015706.1050769-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During the handoff from earlycon to the real console driver, we have
two separate drivers operating on the same device concurrently. In the
case of the 8250 driver these concurrent accesses cause problems due
to the driver's use of banked registers, controlled by LCR.DLAB. It is
possible for the setup(), config_port(), pm() and set_mctrl() callbacks
to set DLAB, which can cause the earlycon code that intends to access
TX to instead access DLL, leading to missed output and corruption on
the serial line due to unintended modifications to the baud rate.
In particular, for setup() we have:
univ8250_console_setup()
-> serial8250_console_setup()
-> uart_set_options()
-> serial8250_set_termios()
-> serial8250_do_set_termios()
-> serial8250_do_set_divisor()
For config_port() we have:
serial8250_config_port()
-> autoconfig()
For pm() we have:
serial8250_pm()
-> serial8250_do_pm()
-> serial8250_set_sleep()
For set_mctrl() we have (for some devices):
serial8250_set_mctrl()
-> omap8250_set_mctrl()
-> __omap8250_set_mctrl()
To avoid such problems, let's make it so that the console is locked
during pre-registration calls to these callbacks, which will prevent
the earlycon driver from running concurrently.
Remove the partial solution to this problem in the 8250 driver
that locked the console only during autoconfig_irq(), as this would
result in a deadlock with the new approach. The console continues
to be locked during autoconfig_irq() because it can only be called
through uart_configure_port().
Although this patch introduces more locking than strictly necessary
(and in particular it also locks during the call to rs485_config()
which is not affected by this issue as far as I can tell), it follows
the principle that it is the responsibility of the generic console
code to manage the earlycon handoff by ensuring that earlycon and real
console driver code cannot run concurrently, and not the individual
drivers.
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reviewed-by: John Ogness <john.ogness@linutronix.de>
Link: https://linux-review.googlesource.com/id/I7cf8124dcebf8618e6b2ee543fa5b25532de55d8
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240304214350.501253-1-pcc@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we have now a common helper to read port properties
use it instead of sparse home grown solution.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Tested-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20240304123035.758700-15-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we have now a common helper to read port properties
use it instead of sparse home grown solution.
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240304123035.758700-11-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we have now a common helper to read port properties
use it instead of sparse home grown solution.
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240304123035.758700-8-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we have now a common helper to read port properties
use it instead of sparse home grown solution.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240304123035.758700-7-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we have now a common helper to read port properties
use it instead of sparse home grown solution.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240304123035.758700-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we have now a common helper to read port properties
use it instead of sparse home grown solution.
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Link: https://lore.kernel.org/r/20240304123035.758700-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several serial drivers want to read the same or similar set of
the port properties. Make a common helper for them.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240304123035.758700-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unlike the 8250 serial driver complex, the sh-sci driver uses only a
single pair of functions to read and write serial port registers.
Hence there is no need to incur the overhead of calling them through
indirection, like the serial_port_{in,out}() wrappers do.
Replace all calls to these wrappers by direct calls to
sci_serial_{in,out}().
Remove the setup of the uart_port.serial_{in,out}() callbacks. After
removal of all calls to serial_port_{in,out}() in the sh-sci driver, the
only remaining user is uart_xchar_out(), which the sh-sci driver does
not use.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Link: https://lore.kernel.org/r/51e79d601cb9d9d63822d3773d3cf05a96868612.1709548811.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is the same issue that was fixed for the VGA text buffer in commit
39cdb68c64 ("vt: fix memory overlapping when deleting chars in the
buffer"). The cure is also the same i.e. replace memcpy() with memmove()
due to the overlaping buffers.
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Fixes: 81732c3b2f ("tty vt: Fix line garbage in virtual console on command line edition")
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/sn184on2-3p0q-0qrq-0218-895349s4753o@syhkavp.arg
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We accidently met the issue that the bash prompt is not shown after the
previous command done and until the next input if there's only one CPU
(In our issue other CPUs are isolated by isolcpus=). Further analysis
shows it's because the port entering runtime suspend even if there's
still pending chars in the buffer and the pending chars will only be
processed in next device resuming. We are using amba-pl011 and the
problematic flow is like below:
Bash kworker
tty_write()
file_tty_write()
n_tty_write()
uart_write()
__uart_start()
pm_runtime_get() // wakeup waker
queue_work()
pm_runtime_work()
rpm_resume()
status = RPM_RESUMING
serial_port_runtime_resume()
port->ops->start_tx()
pl011_tx_chars()
uart_write_wakeup()
[…]
__uart_start()
pm_runtime_get() < 0 // because runtime status = RPM_RESUMING
// later data are not commit to the port driver
status = RPM_ACTIVE
rpm_idle() -> rpm_suspend()
This patch tries to fix this by checking the port busy before entering
runtime suspending. A runtime_suspend callback is added for the port
driver. When entering runtime suspend the callback is invoked, if there's
still pending chars in the buffer then flush the buffer.
Fixes: 84a9582fd2 ("serial: core: Start managing serial controllers to enable runtime PM")
Cc: stable <stable@kernel.org>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Link: https://lore.kernel.org/r/20240226152351.40924-1-yangyicong@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When userspace opens the console, we call set_termios() passing a
termios with the console's configured baud rate. Currently this causes
dw8250_set_termios() to disable and then re-enable the UART clock at
the same frequency as it was originally. This can cause corruption
of any concurrent console output. Fix it by skipping the reclocking
if we are already at the correct rate.
Signed-off-by: Peter Collingbourne <pcc@google.com>
Fixes: 4e26b134bd ("serial: 8250_dw: clock rate handling for all ACPI platforms")
Cc: stable@vger.kernel.org
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240222192635.1050502-1-pcc@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When about to transmit the function imx_uart_start_tx is called and in
some RS485 configurations this function will call imx_uart_stop_rx. The
problem is that imx_uart_stop_rx will enable loopback in order to
release the RS485 bus, but when loopback is enabled transmitted data
will just be looped to RX.
This patch fixes the above problem by not enabling loopback when about
to transmit.
This driver now works well when used for RS485 half duplex master
configurations.
Fixes: 79d0224f6b ("tty: serial: imx: Handle RS485 DE signal active high")
Cc: stable <stable@kernel.org>
Signed-off-by: Rickard x Andersson <rickaran@axis.com>
Tested-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Link: https://lore.kernel.org/r/20240221115304.509811-1-rickaran@axis.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The port lock is a spinlock_t which is becomes a sleeping lock on PREEMPT_RT.
The driver splits the locking function into two parts: local_irq_save() and
uart_port_lock() and this breaks PREEMPT_RT.
Delay handling sysrq until port lock is dropped.
Remove the special case in the console write routine an always use the
complete locking function.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20240301215246.891055-19-bigeasy@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The struct eg20t_port has a spinlock_t which is used for locking while
access I/O of the device. Then there is the uart_portlock which is
sometimes and nests within eg20t_port's lock.
The uart_port lock is not used while using the struct in
pch_uart_hal_read() which might be okay. Then both locks are used in
pch_console_write() which looks odd especially the double try_lock part.
All in all it looks like the uart_port's lock could replace eg20t_port's
lock and simplify the code.
Remove eg20t_port::lock and use uart_port's lock for the lock scope.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20240301215246.891055-18-bigeasy@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to directly initialize the spinlock_t in struct
uart_port. The structure is later passed to uart_add_one_port() which
initialize the complete struct including the lock member.
Remove spin_lock_init() on uart_port's internal lock.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20240301215246.891055-17-bigeasy@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The interrupt service routine is always invoked with disabled
interrupts.
Remove the _irqsave() from the locking functions in the interrupts
service routine/ pch_uart_interrupt().
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20240301215246.891055-16-bigeasy@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
handle_rx() is only a wrapper around handle_rx_to() without any
additional functionality.
Invoke handle_rx_to() directly and remove handle_rx().
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20240301215246.891055-14-bigeasy@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The port lock is a spinlock_t which is becomes a sleeping lock on PREEMPT_RT.
The driver splits the locking function into two parts: local_irq_save() and
uart_port_lock() and this breaks PREEMPT_RT.
Handle sysrq requests sysrq once the port lock is dropped.
Remove the special case in the console write routine an always use the
complete locking function.
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: linux-riscv@lists.infradead.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20240301215246.891055-13-bigeasy@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The port lock is a spinlock_t which is becomes a sleeping lock on PREEMPT_RT.
The driver splits the locking function into two parts: local_irq_save() and
uart_port_lock() and this breaks PREEMPT_RT.
Handle sysrq requests sysrq once the port lock is dropped.
Remove the special case in the console write routine an always use the
complete locking function.
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-unisoc@lists.infradead.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20240301215246.891055-12-bigeasy@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The port lock is a spinlock_t which is becomes a sleeping lock on PREEMPT_RT.
The driver splits the locking function into two parts: local_irq_save() and
uart_port_lock() and this breaks PREEMPT_RT.
Handle sysrq requests sysrq once the port lock is dropped.
Remove the special case in the console write routine an always use the
complete locking function.
Cc: Andreas Färber <afaerber@suse.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-actions@lists.infradead.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20240301215246.891055-11-bigeasy@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The port lock is a spinlock_t which is becomes a sleeping lock on PREEMPT_RT.
The driver splits the locking function into two parts: local_irq_save() and
uart_port_lock() and this breaks PREEMPT_RT.
Handle sysrq requests sysrq once the port lock is dropped.
Remove the special case in the console write routine an always use the
complete locking function.
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20240301215246.891055-10-bigeasy@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The port lock is a spinlock_t which is becomes a sleeping lock on PREEMPT_RT.
The driver splits the locking function into two parts: local_irq_save() and
uart_port_lock() and this breaks PREEMPT_RT.
Delay handling sysrq until port lock is dropped.
Remove the special case in the console write routine an always use the
complete locking function.
Cc: Hammer Hsieh <hammerh0314@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20240301215246.891055-9-bigeasy@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The port lock is a spinlock_t which is becomes a sleeping lock on PREEMPT_RT.
The driver splits the locking function into two parts: local_irq_save() and
uart_port_lock() and this breaks PREEMPT_RT.
Delay handling sysrq until port lock is dropped.
Remove the special case in the console write routine an always use the
complete locking function.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20240301215246.891055-8-bigeasy@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The port lock is a spinlock_t which is becomes a sleeping lock on PREEMPT_RT.
The driver splits the locking function into two parts: local_irq_save() and
uart_port_lock() and this breaks PREEMPT_RT.
Delay handling sysrq until port lock is dropped.
Remove the special case in the console write routine an always use the
complete locking function.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20240301215246.891055-7-bigeasy@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The port lock is a spinlock_t which is becomes a sleeping lock on PREEMPT_RT.
The driver splits the locking function into two parts: local_irq_save() and
uart_port_lock() and this breaks PREEMPT_RT.
Delay handling sysrq until port lock is dropped.
Remove the special case in the console write routine an always use the
complete locking function.
Cc: Bjorn Andersson <andersson@kernel.org>
Cc: Konrad Dybcio <konrad.dybcio@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20240301215246.891055-6-bigeasy@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The port lock is a spinlock_t which is becomes a sleeping lock on PREEMPT_RT.
The driver splits the locking function into two parts: local_irq_save() and
uart_port_lock() and this breaks PREEMPT_RT.
Delay handling sysrq until port lock is dropped.
Remove the special case in the console write routine an always use the
complete locking function.
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-amlogic@lists.infradead.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20240301215246.891055-5-bigeasy@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The port lock is a spinlock_t which is becomes a sleeping lock on PREEMPT_RT.
The driver splits the locking function into two parts: local_irq_save() and
uart_port_lock() and this breaks PREEMPT_RT.
Delay handling sysrq until port lock is dropped.
Remove the special case in the console write routine an always use the
complete locking function.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20240301215246.891055-4-bigeasy@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The port lock is a spinlock_t which is becomes a sleeping lock on PREEMPT_RT.
The driver splits the locking function into two parts: local_irq_save() and
uart_port_lock() and this breaks PREEMPT_RT.
Delay handling sysrq until port lock is dropped.
Remove the special case in the console write routine an always use the
complete locking function.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20240301215246.891055-3-bigeasy@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The port lock is a spinlock_t which is becomes a sleeping lock on PREEMPT_RT.
The driver splits the locking function into two parts: local_irq_save() and
uart_port_lock() and this breaks PREEMPT_RT.
Delay handling sysrq until port lock is dropped.
Remove the special case in the console write routine an always use the
complete locking function.
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20240301215246.891055-2-bigeasy@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of silently giving up, at least tell what the problem is.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240222111922.2016122-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The serial8250_update_uartclk() body was created based on the several
method calls copied from the serial8250_do_set_termios() function. Seeing
aside with some other things the later method can update the baud rate
based on the new reference clock let's just call it instead thus
simplifying the code a bit.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/linux-serial/ZczD7KPbeRnY4CFc@black.fi.intel.com
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20240222145058.28307-1-fancer.lancer@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 1f2bcb8c8c ("gpio: protect the descriptor label with
SRCU") gpiod_set_consumer_name() calls synchronize_srcu() which led to
a "sleeping in atomic context" smatch warning.
This function (along with gpiod_get/put() and all other GPIO APIs apart
from gpiod_get/set_value() and gpiod_direction_input/output()) should
have never been called with a spinlock taken. We're only fixing this now
as GPIOLIB has been rebuilt to use SRCU for access serialization which
uncovered this problem.
Move the calls to gpiod_get/put() outside the spinlock critical section.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/linux-gpio/deee1438-efc1-47c4-8d80-0ab2cf01d60a@moroto.mountain/
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20240220113410.16613-1-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently for platforms which passes UART fifosize from DT gets
override by local driver structure "s3c24xx_serial_drv_data",
which is not intended. Change the code to honor fifosize from
device tree at first.
Signed-off-by: Tamseel Shams <m.shams@samsung.com>
Link: https://lore.kernel.org/r/20240220101227.80741-1-m.shams@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Compiling a kernel for the ColdFire causes a compiler warning:
drivers/tty/serial/mcf.c:473:12: warning: no previous prototype for
‘early_mcf_setup’ [-Wmissing-prototypes]
473 | int __init early_mcf_setup(struct mcf_platform_uart *platp)
| ^~~~~~~~~~~~~~~
This function seems to be completely unused, so let's remove it
to silence the warning.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Acked-by: Greg Ungerer <gerg@linux-m68k.org>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20240219164002.520342-1-thuth@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are not supposed to spread quirks in 8250_port module especially
when we have a separate driver for the hardware in question.
Move quirk from generic module to the driver that uses it.
While at it, move IO to ->set_divisor() callback as it has to be from
day 1. ->get_divisor() is not supposed to perform any IO as UART port:
- might not be powered on
- is not locked by a spin lock
Fixes: 1ed67ecd13 ("8250: microchip: Add 4 Mbps support in PCI1XXXX UART")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Rengarajan S <rengarajan.s@microchip.com>
Link: https://lore.kernel.org/r/20240219162917.2159736-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8250 PCI library provides a common code to map and assign resources.
Use it in order to deduplicate existing code and support IO port
variants.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240219150627.2101198-7-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SIMPLE_DEV_PM_OPS() is deprecated, replace it with DEFINE_SIMPLE_DEV_PM_OPS()
and use pm_sleep_ptr() for setting the driver's PM routines. We can now
remove the __maybe_unused qualifier in the suspend and resume functions.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240219150627.2101198-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While now there is no issue if IRQ is fired before we clearing
the interrupts as the handler does the same, but strictly speaking
it might be problematic if IRQ handler wants to do something more.
Move clearing interrupt code to be called before registering the
IRQ handler.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240219150627.2101198-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
