commit e9fbc47b818b964ddff5df5b2d5c0f5f32f4a147 upstream.
Skip the srso cmd line parsing which is not needed on Zen1/2 with SMT
disabled and with the proper microcode applied (latter should be the
case anyway) as those are not affected.
Fixes: 5a15d8348881 ("x86/srso: Tie SBPB bit setting to microcode patch detection")
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20230813104517.3346-1-bp@alien8.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f58d6fbcb7c848b7f2469be339bc571f2e9d245b upstream.
Initially, it was thought that doing an innocuous division in the #DE
handler would take care to prevent any leaking of old data from the
divider but by the time the fault is raised, the speculation has already
advanced too far and such data could already have been used by younger
operations.
Therefore, do the innocuous division on every exit to userspace so that
userspace doesn't see any potentially old data from integer divisions in
kernel space.
Do the same before VMRUN too, to protect host data from leaking into the
guest too.
Fixes: 77245f1c3c64 ("x86/CPU/AMD: Do not leak quotient data after a division by 0")
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Cc: <stable@kernel.org>
Link: https://lore.kernel.org/r/20230811213824.10025-1-bp@alien8.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ba5ca5e5e6a1d55923e88b4a83da452166f5560e upstream.
Use LEA instead of ADD when adjusting %rsp in srso_safe_ret{,_alias}()
so as to avoid clobbering flags. Drop one of the INT3 instructions to
account for the LEA consuming one more byte than the ADD.
KVM's emulator makes indirect calls into a jump table of sorts, where
the destination of each call is a small blob of code that performs fast
emulation by executing the target instruction with fixed operands.
E.g. to emulate ADC, fastop() invokes adcb_al_dl():
adcb_al_dl:
<+0>: adc %dl,%al
<+2>: jmp <__x86_return_thunk>
A major motivation for doing fast emulation is to leverage the CPU to
handle consumption and manipulation of arithmetic flags, i.e. RFLAGS is
both an input and output to the target of the call. fastop() collects
the RFLAGS result by pushing RFLAGS onto the stack and popping them back
into a variable (held in %rdi in this case):
asm("push %[flags]; popf; " CALL_NOSPEC " ; pushf; pop %[flags]\n"
<+71>: mov 0xc0(%r8),%rdx
<+78>: mov 0x100(%r8),%rcx
<+85>: push %rdi
<+86>: popf
<+87>: call *%rsi
<+89>: nop
<+90>: nop
<+91>: nop
<+92>: pushf
<+93>: pop %rdi
and then propagating the arithmetic flags into the vCPU's emulator state:
ctxt->eflags = (ctxt->eflags & ~EFLAGS_MASK) | (flags & EFLAGS_MASK);
<+64>: and $0xfffffffffffff72a,%r9
<+94>: and $0x8d5,%edi
<+109>: or %rdi,%r9
<+122>: mov %r9,0x10(%r8)
The failures can be most easily reproduced by running the "emulator"
test in KVM-Unit-Tests.
If you're feeling a bit of deja vu, see commit b63f20a778c8
("x86/retpoline: Don't clobber RFLAGS during CALL_NOSPEC on i386").
In addition, this breaks booting of clang-compiled guest on
a gcc-compiled host where the host contains the %rsp-modifying SRSO
mitigations.
[ bp: Massage commit message, extend, remove addresses. ]
Fixes: fb3bd914b3ec ("x86/srso: Add a Speculative RAS Overflow mitigation")
Closes: https://lore.kernel.org/all/de474347-122d-54cd-eabf-9dcc95ab9eae@amd.com
Reported-by: Srikanth Aithal <sraithal@amd.com>
Reported-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/20230810013334.GA5354@dev-arch.thelio-3990X/
Link: https://lore.kernel.org/r/20230811155255.250835-1-seanjc@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54097309620ef0dc2d7083783dc521c6a5fef957 upstream.
Christian reported spurious module load crashes after some of Song's
module memory layout patches.
Turns out that if the very last instruction on the very last page of the
module is a 'JMP __x86_return_thunk' then __static_call_fixup() will
trip a fault and die.
And while the module rework made this slightly more likely to happen,
it's always been possible.
Fixes: ee88d363d156 ("x86,static_call: Use alternative RET encoding")
Reported-by: Christian Bricart <christian@bricart.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Josh Poimboeuf <jpoimboe@kernel.org>
Link: https://lkml.kernel.org/r/20230816104419.GA982867@hirez.programming.kicks-ass.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9dbd23e42ff0b10c9b02c9e649c76e5228241a8e upstream.
The goal is to eventually have a proper documentation about all this.
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20230814164447.GFZNpZ/64H4lENIe94@fat_crate.local
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7c25c441e9e0fa75b4c83e0b26306b702cfe90d upstream.
Since there can only be one active return_thunk, there only needs be
one (matching) untrain_ret. It fundamentally doesn't make sense to
allow multiple untrain_ret at the same time.
Fold all the 3 different untrain methods into a single (temporary)
helper stub.
Fixes: fb3bd914b3ec ("x86/srso: Add a Speculative RAS Overflow mitigation")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20230814121149.042774962@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d43490d0ab824023e11d0b57d0aeec17a6e0ca13 upstream.
Use the existing configurable return thunk. There is absolute no
justification for having created this __x86_return_thunk alternative.
To clarify, the whole thing looks like:
Zen3/4 does:
srso_alias_untrain_ret:
nop2
lfence
jmp srso_alias_return_thunk
int3
srso_alias_safe_ret: // aliasses srso_alias_untrain_ret just so
add $8, %rsp
ret
int3
srso_alias_return_thunk:
call srso_alias_safe_ret
ud2
While Zen1/2 does:
srso_untrain_ret:
movabs $foo, %rax
lfence
call srso_safe_ret (jmp srso_return_thunk ?)
int3
srso_safe_ret: // embedded in movabs instruction
add $8,%rsp
ret
int3
srso_return_thunk:
call srso_safe_ret
ud2
While retbleed does:
zen_untrain_ret:
test $0xcc, %bl
lfence
jmp zen_return_thunk
int3
zen_return_thunk: // embedded in the test instruction
ret
int3
Where Zen1/2 flush the BTB entry using the instruction decoder trick
(test,movabs) Zen3/4 use BTB aliasing. SRSO adds a return sequence
(srso_safe_ret()) which forces the function return instruction to
speculate into a trap (UD2). This RET will then mispredict and
execution will continue at the return site read from the top of the
stack.
Pick one of three options at boot (evey function can only ever return
once).
[ bp: Fixup commit message uarch details and add them in a comment in
the code too. Add a comment about the srso_select_mitigation()
dependency on retbleed_select_mitigation(). Add moar ifdeffery for
32-bit builds. Add a dummy srso_untrain_ret_alias() definition for
32-bit alternatives needing the symbol. ]
Fixes: fb3bd914b3ec ("x86/srso: Add a Speculative RAS Overflow mitigation")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20230814121148.842775684@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c8c301abeae58ec756b8fcb2178a632bd3c9e284 ]
In order to have objtool warn about code references to !ENDBR
instruction, we need an annotation to allow this for non-control-flow
instances -- consider text range checks, text patching, or return
trampolines etc.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lore.kernel.org/r/20220308154317.578968224@infradead.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e028c4f7ac7ca8c96126fe46c54ab3d56ffe6a66 ]
Add a CONFIG_FRAME_POINTER-specific version of
STACK_FRAME_NON_STANDARD() for the case where a function is
intentionally missing frame pointer setup, but otherwise needs
objtool/ORC coverage when frame pointers are disabled.
Link: https://lkml.kernel.org/r/163163047364.489837.17377799909553689661.stgit@devnote2
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Tested-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Stable-dep-of: c8c301abeae5 ("x86/ibt: Add ANNOTATE_NOENDBR")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 095b8303f3835c68ac4a8b6d754ca1c3b6230711 upstream.
There is infrastructure to rewrite return thunks to point to any
random thunk one desires, unwrap that from CALL_THUNKS, which up to
now was the sole user of that.
[ bp: Make the thunks visible on 32-bit and add ifdeffery for the
32-bit builds. ]
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20230814121148.775293785@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit af023ef335f13c8b579298fc432daeef609a9e60 upstream.
vmlinux.o: warning: objtool: srso_untrain_ret() falls through to next function __x86_return_skl()
vmlinux.o: warning: objtool: __x86_return_thunk() falls through to next function __x86_return_skl()
This is because these functions (can) end with CALL, which objtool
does not consider a terminating instruction. Therefore, replace the
INT3 instruction (which is a non-fatal trap) with UD2 (which is a
fatal-trap).
This indicates execution will not continue past this point.
Fixes: fb3bd914b3ec ("x86/srso: Add a Speculative RAS Overflow mitigation")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20230814121148.637802730@infradead.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 77f67119004296a9b2503b377d610e08b08afc2a upstream.
Commit
fb3bd914b3ec ("x86/srso: Add a Speculative RAS Overflow mitigation")
reimplemented __x86_return_thunk with a mix of SYM_FUNC_START and
SYM_CODE_END, this is not a sane combination.
Since nothing should ever actually 'CALL' this, make it consistently
CODE.
Fixes: fb3bd914b3ec ("x86/srso: Add a Speculative RAS Overflow mitigation")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20230814121148.571027074@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e4dd0d3a2f64b8bd8029ec70f52bdbebd0644408 upstream.
In the real workload, I encountered an issue which could cause the RTO
timer to retransmit the skb per 1ms with linear option enabled. The amount
of lost-retransmitted skbs can go up to 1000+ instantly.
The root cause is that if the icsk_rto happens to be zero in the 6th round
(which is the TCP_THIN_LINEAR_RETRIES value), then it will always be zero
due to the changed calculation method in tcp_retransmit_timer() as follows:
icsk->icsk_rto = min(icsk->icsk_rto << 1, TCP_RTO_MAX);
Above line could be converted to
icsk->icsk_rto = min(0 << 1, TCP_RTO_MAX) = 0
Therefore, the timer expires so quickly without any doubt.
I read through the RFC 6298 and found that the RTO value can be rounded
up to a certain value, in Linux, say TCP_RTO_MIN as default, which is
regarded as the lower bound in this patch as suggested by Eric.
Fixes: 36e31b0af587 ("net: TCP thin linear timeouts")
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 51b813176f098ff61bd2833f627f5319ead098a5 upstream.
Commit 25266128fe16 ("virtio-net: fix race between set queues and
probe") tries to fix the race between set queues and probe by calling
_virtnet_set_queues() before DRIVER_OK is set. This violates virtio
spec. Fixing this by setting queues after virtio_device_ready().
Note that rtnl needs to be held for userspace requests to change the
number of queues. So we are serialized in this way.
Fixes: 25266128fe16 ("virtio-net: fix race between set queues and probe")
Reported-by: Dragos Tatulea <dtatulea@nvidia.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9bfab6d23a2865966a4f89a96536fbf23f83bc8c upstream.
In SCTP protocol, it is using the same timer (T2 timer) for SHUTDOWN and
SHUTDOWN_ACK retransmission. However in sctp conntrack the default timeout
value for SCTP_CONNTRACK_SHUTDOWN_ACK_SENT state is 3 secs while it's 300
msecs for SCTP_CONNTRACK_SHUTDOWN_SEND/RECV state.
As Paolo Valerio noticed, this might cause unwanted expiration of the ct
entry. In my test, with 1s tc netem delay set on the NAT path, after the
SHUTDOWN is sent, the sctp ct entry enters SCTP_CONNTRACK_SHUTDOWN_SEND
state. However, due to 300ms (too short) delay, when the SHUTDOWN_ACK is
sent back from the peer, the sctp ct entry has expired and been deleted,
and then the SHUTDOWN_ACK has to be dropped.
Also, it is confusing these two sysctl options always show 0 due to all
timeout values using sec as unit:
net.netfilter.nf_conntrack_sctp_timeout_shutdown_recd = 0
net.netfilter.nf_conntrack_sctp_timeout_shutdown_sent = 0
This patch fixes it by also using 3 secs for sctp shutdown send and recv
state in sctp conntrack, which is also RTO.initial value in SCTP protocol.
Note that the very short time value for SCTP_CONNTRACK_SHUTDOWN_SEND/RECV
was probably used for a rare scenario where SHUTDOWN is sent on 1st path
but SHUTDOWN_ACK is replied on 2nd path, then a new connection started
immediately on 1st path. So this patch also moves from SHUTDOWN_SEND/RECV
to CLOSE when receiving INIT in the ORIGINAL direction.
Fixes: 9fb9cbb1082d ("[NETFILTER]: Add nf_conntrack subsystem.")
Reported-by: Paolo Valerio <pvalerio@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4b430d4ac99750ee2ae2f893f1055c7af1ec3dc5 upstream.
For a completed request, after the mmc_blk_mq_complete_rq(mq, req)
function is executed, the bitmap_tags corresponding to the
request will be cleared, that is, the request will be regarded as
idle. If the request is acquired by a different type of process at
this time, the issue_type of the request may change. It further
caused the value of mq->in_flight[issue_type] to be abnormal,
and a large number of requests could not be sent.
p1: p2:
mmc_blk_mq_complete_rq
blk_mq_free_request
blk_mq_get_request
blk_mq_rq_ctx_init
mmc_blk_mq_dec_in_flight
mmc_issue_type(mq, req)
This strategy can ensure the consistency of issue_type
before and after executing mmc_blk_mq_complete_rq.
Fixes: 81196976ed94 ("mmc: block: Add blk-mq support")
Cc: stable@vger.kernel.org
Signed-off-by: Yibin Ding <yibin.ding@unisoc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230802023023.1318134-1-yunlong.xing@unisoc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d83035433701919ac6db15f7737cbf554c36c1a6 upstream.
mmc_free_host() has already be called in wbsd_free_mmc(),
remove the mmc_free_host() in error path in wbsd_init().
Fixes: dc5b9b50fc9d ("mmc: wbsd: fix return value check of mmc_add_host()")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230807124443.3431366-1-yangyingliang@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 69513dd669e243928f7450893190915a88f84a2b upstream.
Under the current code, when cifs_readpage_worker is called, the call
contract is that the callee should unlock the page. This is documented
in the read_folio section of Documentation/filesystems/vfs.rst as:
> The filesystem should unlock the folio once the read has completed,
> whether it was successful or not.
Without this change, when fscache is in use and cache hit occurs during
a read, the page lock is leaked, producing the following stack on
subsequent reads (via mmap) to the page:
$ cat /proc/3890/task/12864/stack
[<0>] folio_wait_bit_common+0x124/0x350
[<0>] filemap_read_folio+0xad/0xf0
[<0>] filemap_fault+0x8b1/0xab0
[<0>] __do_fault+0x39/0x150
[<0>] do_fault+0x25c/0x3e0
[<0>] __handle_mm_fault+0x6ca/0xc70
[<0>] handle_mm_fault+0xe9/0x350
[<0>] do_user_addr_fault+0x225/0x6c0
[<0>] exc_page_fault+0x84/0x1b0
[<0>] asm_exc_page_fault+0x27/0x30
This requires a reboot to resolve; it is a deadlock.
Note however that the call to cifs_readpage_from_fscache does mark the
page clean, but does not free the folio lock. This happens in
__cifs_readpage_from_fscache on success. Releasing the lock at that
point however is not appropriate as cifs_readahead also calls
cifs_readpage_from_fscache and *does* unconditionally release the lock
after its return. This change therefore effectively makes
cifs_readpage_worker work like cifs_readahead.
Signed-off-by: Russell Harmon <russ@har.mn>
Acked-by: Paulo Alcantara (SUSE) <pc@manguebit.com>
Reviewed-by: David Howells <dhowells@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dfe2aeb226fd5e19b0ee795f4f6ed8bc494c1534 ]
Unloading a hardware specific 8250 driver can produce error "Unable to
handle kernel paging request at virtual address" about ten seconds after
unloading the driver. This happens on uart_hangup() calling
uart_change_pm().
Turns out commit 04e82793f068 ("serial: 8250: Reinit port->pm on port
specific driver unbind") was only a partial fix. If the hardware specific
driver has initialized port->pm function, we need to clear port->pm too.
Just reinitializing port->ops does not do this. Otherwise serial8250_pm()
will call port->pm() instead of serial8250_do_pm().
Fixes: 04e82793f068 ("serial: 8250: Reinit port->pm on port specific driver unbind")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230804131553.52927-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46cdff2369cbdf8d78081a22526e77bd1323f563 ]
Set spec->en_3kpull_low default to true.
Then fillback ALC236 and ALC257 to false.
Additional note: this addresses a regression caused by the previous
fix 69ea4c9d02b7 ("ALSA: hda/realtek - remove 3k pull low procedure").
The previous workaround was applied too widely without necessity,
which resulted in the pop noise at PM again. This patch corrects the
condition and restores the old behavior for the devices that don't
suffer from the original problem.
Fixes: 69ea4c9d02b7 ("ALSA: hda/realtek - remove 3k pull low procedure")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217732
Link: https://lore.kernel.org/r/01e212a538fc407ca6edd10b81ff7b05@realtek.com
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1f848f12103920ca165758aedb1c10904e193e1 ]
When the tdm lane mask is computed, the driver currently fills the 1st lane
before moving on to the next. If the stream has less channels than the
lanes can accommodate, slots will be disabled on the last lanes.
Unfortunately, the HW distribute channels in a different way. It distribute
channels in pair on each lanes before moving on the next slots.
This difference leads to problems if a device has an interface with more
than 1 lane and with more than 2 slots per lane.
For example: a playback interface with 2 lanes and 4 slots each (total 8
slots - zero based numbering)
- Playing a 8ch stream:
- All slots activated by the driver
- channel #2 will be played on lane #1 - slot #0 following HW placement
- Playing a 4ch stream:
- Lane #1 disabled by the driver
- channel #2 will be played on lane #0 - slot #2
This behaviour is obviously not desirable.
Change the way slots are activated on the TDM lanes to follow what the HW
does and make sure each channel always get mapped to the same slot/lane.
Fixes: 1a11d88f499c ("ASoC: meson: add tdm formatter base driver")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20230809171931.1244502-1-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cee572756aa2cb46e959e9797ad4b730b78a050b ]
There is some instablity with some eMMC modules on ROCK Pi 4 SBCs running
in HS400 mode. This ends up resulting in some block errors after a while
or after a "heavy" operation utilising the eMMC (e.g. resizing a
filesystem). An example of these errors is as follows:
[ 289.171014] mmc1: running CQE recovery
[ 290.048972] mmc1: running CQE recovery
[ 290.054834] mmc1: running CQE recovery
[ 290.060817] mmc1: running CQE recovery
[ 290.061337] blk_update_request: I/O error, dev mmcblk1, sector 1411072 op 0x1:(WRITE) flags 0x800 phys_seg 36 prio class 0
[ 290.061370] EXT4-fs warning (device mmcblk1p1): ext4_end_bio:348: I/O error 10 writing to inode 29547 starting block 176466)
[ 290.061484] Buffer I/O error on device mmcblk1p1, logical block 172288
[ 290.061531] Buffer I/O error on device mmcblk1p1, logical block 172289
[ 290.061551] Buffer I/O error on device mmcblk1p1, logical block 172290
[ 290.061574] Buffer I/O error on device mmcblk1p1, logical block 172291
[ 290.061592] Buffer I/O error on device mmcblk1p1, logical block 172292
[ 290.061615] Buffer I/O error on device mmcblk1p1, logical block 172293
[ 290.061632] Buffer I/O error on device mmcblk1p1, logical block 172294
[ 290.061654] Buffer I/O error on device mmcblk1p1, logical block 172295
[ 290.061673] Buffer I/O error on device mmcblk1p1, logical block 172296
[ 290.061695] Buffer I/O error on device mmcblk1p1, logical block 172297
Disabling the Command Queue seems to stop the CQE recovery from running,
but doesn't seem to improve the I/O errors. Until this can be investigated
further, disable HS400 mode on the ROCK Pi 4 SBCs to at least stop I/O
errors from occurring.
While we are here, set the eMMC maximum clock frequency to 1.5MHz to
follow the ROCK 4C+.
Fixes: 1b5715c602fd ("arm64: dts: rockchip: add ROCK Pi 4 DTS support")
Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
Tested-By: Folker Schwesinger <dev@folker-schwesinger.de>
Link: https://lore.kernel.org/r/20230705144255.115299-2-chris.obbard@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 697dd494cb1cf56acfb764214a1e4788e4d1a983 ]
Add a SPDIF audio-graph-card to ROCK Pi 4 device tree.
It's not enabled by default since all dma channels are used by
the (already) enabled i2s0/1/2 and the pin is muxed with GPIO4_C5
which might be in use already.
If enabled SPDIF_TX will be available at pin #15.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Link: https://lore.kernel.org/r/20210618181256.27992-6-knaerzche@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Stable-dep-of: cee572756aa2 ("arm64: dts: rockchip: Disable HS400 for eMMC on ROCK Pi 4")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65bd2b8bdb3bddc37bea695789713916327e1c1f ]
ROCK Pi 4 boards have the codec connected to i2s0 and it is accessible
via i2c1 address 0x11.
Add an audio-graph-card for it.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Link: https://lore.kernel.org/r/20210618181256.27992-5-knaerzche@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Stable-dep-of: cee572756aa2 ("arm64: dts: rockchip: Disable HS400 for eMMC on ROCK Pi 4")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e12f67fe83446432ef16704c22ec23bd1dbcd094 ]
Based on the board schematics at
https://dl.radxa.com/rockpi4/docs/hw/rockpi4/rockpi_4c_v12_sch_20200620.pdf
on page 19 there is an USB Type-A receptacle being used as an USB-OTG port.
But the Type-A connector is not valid for OTG operation, for this reason
there is a switch to select host or device role.
This is non-compliant and error prone because switching is manual.
So, use host mode as it corresponds for a Type-A receptacle.
Signed-off-by: Vicente Bergas <vicencb@gmail.com>
Link: https://lore.kernel.org/r/20201201154132.1286-4-vicencb@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Stable-dep-of: cee572756aa2 ("arm64: dts: rockchip: Disable HS400 for eMMC on ROCK Pi 4")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 328c6112787bf7562dbea638840366cd197868d6 ]
Based on the board schematics at
https://dl.radxa.com/rockpi4/docs/hw/rockpi4/rockpi_4c_v12_sch_20200620.pdf
on page 18:
vcc_lan is not controllable by software, it is just an analog LC filter.
Because of this, it can not be turned off-in-suspend.
and on page 17:
vcc_cam and vcc_mipi are not voltage regulators, they are just switches.
So, the voltage range is not applicable.
This silences an error message about not being able to adjust the voltage.
Signed-off-by: Vicente Bergas <vicencb@gmail.com>
Link: https://lore.kernel.org/r/20201201154132.1286-2-vicencb@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Stable-dep-of: cee572756aa2 ("arm64: dts: rockchip: Disable HS400 for eMMC on ROCK Pi 4")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 34539b442b3bc7d5bf10164750302b60b91f18a7 ]
The am335x devices started producing boot errors for resetting musb module
in because of subtle timing changes:
Unhandled fault: external abort on non-linefetch (0x1008)
...
sysc_poll_reset_sysconfig from sysc_reset+0x109/0x12
sysc_reset from sysc_probe+0xa99/0xeb0
...
The fix is to flush posted write after enable before reset during
probe. Note that some devices also need to specify the delay after enable
with ti,sysc-delay-us, but this is not needed for musb on am335x based on
my tests.
Reported-by: kernelci.org bot <bot@kernelci.org>
Closes: https://storage.kernelci.org/next/master/next-20230614/arm/multi_v7_defconfig+CONFIG_THUMB2_KERNEL=y/gcc-10/lab-cip/baseline-beaglebone-black.html
Fixes: 596e7955692b ("bus: ti-sysc: Add support for software reset")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2d0c88e84e483982067a82073f6125490ddf3614 ]
The status of global socket memory pressure is updated when:
a) __sk_mem_raise_allocated():
enter: sk_memory_allocated(sk) > sysctl_mem[1]
leave: sk_memory_allocated(sk) <= sysctl_mem[0]
b) __sk_mem_reduce_allocated():
leave: sk_under_memory_pressure(sk) &&
sk_memory_allocated(sk) < sysctl_mem[0]
So the conditions of leaving global pressure are inconstant, which
may lead to the situation that one pressured net-memcg prevents the
global pressure from being cleared when there is indeed no global
pressure, thus the global constrains are still in effect unexpectedly
on the other sockets.
This patch fixes this by ignoring the net-memcg's pressure when
deciding whether should leave global memory pressure.
Fixes: e1aab161e013 ("socket: initial cgroup code.")
Signed-off-by: Abel Wu <wuyun.abel@bytedance.com>
Acked-by: Shakeel Butt <shakeelb@google.com>
Link: https://lore.kernel.org/r/20230816091226.1542-1-wuyun.abel@bytedance.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23d775f12dcd23d052a4927195f15e970e27ab26 ]
If the switch is reset during active EEPROM transactions, as in
just after an SoC reset after power up, the I2C bus transaction
may be cut short leaving the EEPROM internal I2C state machine
in the wrong state. When the switch is reset again, the bad
state machine state may result in data being read from the wrong
memory location causing the switch to enter unexpected mode
rendering it inoperational.
Fixes: a3dcb3e7e70c ("net: dsa: mv88e6xxx: Wait for EEPROM done after HW reset")
Signed-off-by: Alfred Lee <l00g33k@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230815001323.24739-1-l00g33k@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f2beb8874cb0844e84ad26e990f05f4f13ff63f ]
Change "write" into the actual "read" word.
Change parameters description.
Fixes: 7073f46e443e ("i40e: Add AQ commands for NVM Update for X722")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Andrii Staikov <andrii.staikov@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dafcbce07136d799edc4c67f04f9fd69ff1eac1f ]
Similar to commit 01f4fd270870 ("bonding: Fix incorrect deletion of
ETH_P_8021AD protocol vid from slaves"), we can trigger BUG_ON(!vlan_info)
in unregister_vlan_dev() with the following testcase:
# ip netns add ns1
# ip netns exec ns1 ip link add team1 type team
# ip netns exec ns1 ip link add team_slave type veth peer veth2
# ip netns exec ns1 ip link set team_slave master team1
# ip netns exec ns1 ip link add link team_slave name team_slave.10 type vlan id 10 protocol 802.1ad
# ip netns exec ns1 ip link add link team1 name team1.10 type vlan id 10 protocol 802.1ad
# ip netns exec ns1 ip link set team_slave nomaster
# ip netns del ns1
Add S-VLAN tag related features support to team driver. So the team driver
will always propagate the VLAN info to its slaves.
Fixes: 8ad227ff89a7 ("net: vlan: add 802.1ad support")
Suggested-by: Ido Schimmel <idosch@idosch.org>
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230814032301.2804971-1-william.xuanziyang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 096516d092d54604d590827d05b1022c8f326639 ]
The 54810 does not support c45. The mmd_phy_indirect accesses return
arbirtary values leading to odd behavior like saying it supports EEE
when it doesn't. We also see that reading/writing these non-existent
MMD registers leads to phy instability in some cases.
Fixes: b14995ac2527 ("net: phy: broadcom: Add BCM54810 PHY entry")
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/1691901708-28650-1-git-send-email-justin.chen@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23185c6aed1ffb8fc44087880ba2767aba493779 ]
Do not allow to insert elements from datapath to objects maps.
Fixes: 8aeff920dcc9 ("netfilter: nf_tables: add stateful object reference to set elements")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5310760af1d4fbea1452bfc77db5f9a680f7ae47 ]
When two threads run proc_do_sync_threshold() in parallel,
data races could happen between the two memcpy():
Thread-1 Thread-2
memcpy(val, valp, sizeof(val));
memcpy(valp, val, sizeof(val));
This race might mess up the (struct ctl_table *) table->data,
so we add a mutex lock to serialize them.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Link: https://lore.kernel.org/netdev/B6988E90-0A1E-4B85-BF26-2DAF6D482433@gmail.com/
Signed-off-by: Sishuai Gong <sishuai.system@gmail.com>
Acked-by: Simon Horman <horms@kernel.org>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8470c0a7bcaa82f78ad34282d662dd7bd9630c2 ]
Commit 03e909acd95a ("drm/panel: simple: Add support for AUO G121EAN01.4
panel") added support for this panel model, but the timings it implements
are very different from what the datasheet describes. I checked both the
G121EAN01.0 datasheet from [0] and the G121EAN01.4 one from [1] and they
all have the same timings: for example the LVDS clock typical value is 74.4
MHz, not 66.7 MHz as implemented.
Replace the timings with the ones from the documentation. These timings
have been tested and the clock frequencies verified with an oscilloscope to
ensure they are correct.
Also use struct display_timing instead of struct drm_display_mode in order
to also specify the minimum and maximum values.
[0] https://embedded.avnet.com/product/g121ean01-0/
[1] https://embedded.avnet.com/product/g121ean01-4/
Fixes: 03e909acd95a ("drm/panel: simple: Add support for AUO G121EAN01.4 panel")
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230804151239.835216-1-luca.ceresoli@bootlin.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 855067defa36b1f9effad8c219d9a85b655cf500 ]
This test verifies whether the encapsulated packets have the correct
configured TTL. It does so by sending ICMP packets through the test
topology and mirroring them to a gretap netdevice. On a busy host
however, more than just the test ICMP packets may end up flowing
through the topology, get mirrored, and counted. This leads to
potential spurious failures as the test observes much more mirrored
packets than the sent test packets, and assumes a bug.
Fix this by tightening up the mirror action match. Change it from
matchall to a flower classifier matching on ICMP packets specifically.
Fixes: 45315673e0c5 ("selftests: forwarding: Test changes in mirror-to-gretap")
Signed-off-by: Petr Machata <petrm@nvidia.com>
Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5e2424708da7207087934c5c75211e8584d553a0 ]
The previous commit 4e484b3e969b ("xfrm: rate limit SA mapping change
message to user space") added one additional attribute named
XFRMA_MTIMER_THRESH and described its type at compat_policy
(net/xfrm/xfrm_compat.c).
However, the author forgot to also describe the nla_policy at
xfrma_policy (net/xfrm/xfrm_user.c). Hence, this suppose NLA_U32 (4
bytes) value can be faked as empty (0 bytes) by a malicious user, which
leads to 4 bytes overflow read and heap information leak when parsing
nlattrs.
To exploit this, one malicious user can spray the SLUB objects and then
leverage this 4 bytes OOB read to leak the heap data into
x->mapping_maxage (see xfrm_update_ae_params(...)), and leak it to
userspace via copy_to_user_state_extra(...).
The above bug is assigned CVE-2023-3773. To fix it, this commit just
completes the nla_policy description for XFRMA_MTIMER_THRESH, which
enforces the length check and avoids such OOB read.
Fixes: 4e484b3e969b ("xfrm: rate limit SA mapping change message to user space")
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6018a266279b1a75143c7c0804dd08a5fc4c3e0b ]
When ip_vti device is set to the qdisc of the sfb type, the cb field
of the sent skb may be modified during enqueuing. Then,
slab-use-after-free may occur when ip_vti device sends IPv6 packets.
As commit f855691975bb ("xfrm6: Fix the nexthdr offset in
_decode_session6.") showed, xfrm_decode_session was originally intended
only for the receive path. IP6CB(skb)->nhoff is not set during
transmission. Therefore, set the cb field in the skb to 0 before
sending packets.
Fixes: f855691975bb ("xfrm6: Fix the nexthdr offset in _decode_session6.")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9fd41f1ba638938c9a1195d09bc6fa3be2712f25 ]
When ipv6_vti device is set to the qdisc of the sfb type, the cb field
of the sent skb may be modified during enqueuing. Then,
slab-use-after-free may occur when ipv6_vti device sends IPv6 packets.
The stack information is as follows:
BUG: KASAN: slab-use-after-free in decode_session6+0x103f/0x1890
Read of size 1 at addr ffff88802e08edc2 by task swapper/0/0
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 6.4.0-next-20230707-00001-g84e2cad7f979 #410
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-1.fc33 04/01/2014
Call Trace:
<IRQ>
dump_stack_lvl+0xd9/0x150
print_address_description.constprop.0+0x2c/0x3c0
kasan_report+0x11d/0x130
decode_session6+0x103f/0x1890
__xfrm_decode_session+0x54/0xb0
vti6_tnl_xmit+0x3e6/0x1ee0
dev_hard_start_xmit+0x187/0x700
sch_direct_xmit+0x1a3/0xc30
__qdisc_run+0x510/0x17a0
__dev_queue_xmit+0x2215/0x3b10
neigh_connected_output+0x3c2/0x550
ip6_finish_output2+0x55a/0x1550
ip6_finish_output+0x6b9/0x1270
ip6_output+0x1f1/0x540
ndisc_send_skb+0xa63/0x1890
ndisc_send_rs+0x132/0x6f0
addrconf_rs_timer+0x3f1/0x870
call_timer_fn+0x1a0/0x580
expire_timers+0x29b/0x4b0
run_timer_softirq+0x326/0x910
__do_softirq+0x1d4/0x905
irq_exit_rcu+0xb7/0x120
sysvec_apic_timer_interrupt+0x97/0xc0
</IRQ>
Allocated by task 9176:
kasan_save_stack+0x22/0x40
kasan_set_track+0x25/0x30
__kasan_slab_alloc+0x7f/0x90
kmem_cache_alloc_node+0x1cd/0x410
kmalloc_reserve+0x165/0x270
__alloc_skb+0x129/0x330
netlink_sendmsg+0x9b1/0xe30
sock_sendmsg+0xde/0x190
____sys_sendmsg+0x739/0x920
___sys_sendmsg+0x110/0x1b0
__sys_sendmsg+0xf7/0x1c0
do_syscall_64+0x39/0xb0
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Freed by task 9176:
kasan_save_stack+0x22/0x40
kasan_set_track+0x25/0x30
kasan_save_free_info+0x2b/0x40
____kasan_slab_free+0x160/0x1c0
slab_free_freelist_hook+0x11b/0x220
kmem_cache_free+0xf0/0x490
skb_free_head+0x17f/0x1b0
skb_release_data+0x59c/0x850
consume_skb+0xd2/0x170
netlink_unicast+0x54f/0x7f0
netlink_sendmsg+0x926/0xe30
sock_sendmsg+0xde/0x190
____sys_sendmsg+0x739/0x920
___sys_sendmsg+0x110/0x1b0
__sys_sendmsg+0xf7/0x1c0
do_syscall_64+0x39/0xb0
entry_SYSCALL_64_after_hwframe+0x63/0xcd
The buggy address belongs to the object at ffff88802e08ed00
which belongs to the cache skbuff_small_head of size 640
The buggy address is located 194 bytes inside of
freed 640-byte region [ffff88802e08ed00, ffff88802e08ef80)
As commit f855691975bb ("xfrm6: Fix the nexthdr offset in
_decode_session6.") showed, xfrm_decode_session was originally intended
only for the receive path. IP6CB(skb)->nhoff is not set during
transmission. Therefore, set the cb field in the skb to 0 before
sending packets.
Fixes: f855691975bb ("xfrm6: Fix the nexthdr offset in _decode_session6.")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 53223f2ed1ef5c90dad814daaaefea4e68a933c8 ]
When the xfrm device is set to the qdisc of the sfb type, the cb field
of the sent skb may be modified during enqueuing. Then,
slab-use-after-free may occur when the xfrm device sends IPv6 packets.
The stack information is as follows:
BUG: KASAN: slab-use-after-free in decode_session6+0x103f/0x1890
Read of size 1 at addr ffff8881111458ef by task swapper/3/0
CPU: 3 PID: 0 Comm: swapper/3 Not tainted 6.4.0-next-20230707 #409
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-1.fc33 04/01/2014
Call Trace:
<IRQ>
dump_stack_lvl+0xd9/0x150
print_address_description.constprop.0+0x2c/0x3c0
kasan_report+0x11d/0x130
decode_session6+0x103f/0x1890
__xfrm_decode_session+0x54/0xb0
xfrmi_xmit+0x173/0x1ca0
dev_hard_start_xmit+0x187/0x700
sch_direct_xmit+0x1a3/0xc30
__qdisc_run+0x510/0x17a0
__dev_queue_xmit+0x2215/0x3b10
neigh_connected_output+0x3c2/0x550
ip6_finish_output2+0x55a/0x1550
ip6_finish_output+0x6b9/0x1270
ip6_output+0x1f1/0x540
ndisc_send_skb+0xa63/0x1890
ndisc_send_rs+0x132/0x6f0
addrconf_rs_timer+0x3f1/0x870
call_timer_fn+0x1a0/0x580
expire_timers+0x29b/0x4b0
run_timer_softirq+0x326/0x910
__do_softirq+0x1d4/0x905
irq_exit_rcu+0xb7/0x120
sysvec_apic_timer_interrupt+0x97/0xc0
</IRQ>
<TASK>
asm_sysvec_apic_timer_interrupt+0x1a/0x20
RIP: 0010:intel_idle_hlt+0x23/0x30
Code: 1f 84 00 00 00 00 00 f3 0f 1e fa 41 54 41 89 d4 0f 1f 44 00 00 66 90 0f 1f 44 00 00 0f 00 2d c4 9f ab 00 0f 1f 44 00 00 fb f4 <fa> 44 89 e0 41 5c c3 66 0f 1f 44 00 00 f3 0f 1e fa 41 54 41 89 d4
RSP: 0018:ffffc90000197d78 EFLAGS: 00000246
RAX: 00000000000a83c3 RBX: ffffe8ffffd09c50 RCX: ffffffff8a22d8e5
RDX: 0000000000000001 RSI: ffffffff8d3f8080 RDI: ffffe8ffffd09c50
RBP: ffffffff8d3f8080 R08: 0000000000000001 R09: ffffed1026ba6d9d
R10: ffff888135d36ceb R11: 0000000000000001 R12: 0000000000000001
R13: ffffffff8d3f8100 R14: 0000000000000001 R15: 0000000000000000
cpuidle_enter_state+0xd3/0x6f0
cpuidle_enter+0x4e/0xa0
do_idle+0x2fe/0x3c0
cpu_startup_entry+0x18/0x20
start_secondary+0x200/0x290
secondary_startup_64_no_verify+0x167/0x16b
</TASK>
Allocated by task 939:
kasan_save_stack+0x22/0x40
kasan_set_track+0x25/0x30
__kasan_slab_alloc+0x7f/0x90
kmem_cache_alloc_node+0x1cd/0x410
kmalloc_reserve+0x165/0x270
__alloc_skb+0x129/0x330
inet6_ifa_notify+0x118/0x230
__ipv6_ifa_notify+0x177/0xbe0
addrconf_dad_completed+0x133/0xe00
addrconf_dad_work+0x764/0x1390
process_one_work+0xa32/0x16f0
worker_thread+0x67d/0x10c0
kthread+0x344/0x440
ret_from_fork+0x1f/0x30
The buggy address belongs to the object at ffff888111145800
which belongs to the cache skbuff_small_head of size 640
The buggy address is located 239 bytes inside of
freed 640-byte region [ffff888111145800, ffff888111145a80)
As commit f855691975bb ("xfrm6: Fix the nexthdr offset in
_decode_session6.") showed, xfrm_decode_session was originally intended
only for the receive path. IP6CB(skb)->nhoff is not set during
transmission. Therefore, set the cb field in the skb to 0 before
sending packets.
Fixes: f855691975bb ("xfrm6: Fix the nexthdr offset in _decode_session6.")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
