Create function smp_ata_check_ready_type() for LLDDs to wait for SATA
devices to come up after a link reset.
Signed-off-by: Jie Zhan <zhanjie9@hisilicon.com>
Link: https://lore.kernel.org/r/20221118083714.4034612-4-zhanjie9@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The SAS address comparison of asd_sas_port and expander phy is open
coded. Replace it with sas_phy_match_port_addr().
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Link: https://lore.kernel.org/r/20220928070130.3657183-9-yanaijie@huawei.com
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The SAS address comparison of expander phys is open coded. Replace it with
sas_phy_addr_match().
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Link: https://lore.kernel.org/r/20220928070130.3657183-8-yanaijie@huawei.com
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The SAS address comparison of domain device and expander phy is open
coded. Replace it with sas_phy_match_dev_addr().
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Link: https://lore.kernel.org/r/20220928070130.3657183-7-yanaijie@huawei.com
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
LLDDs are all implementing their own attached phy ID finding code. Factor
it out to libsas.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Link: https://lore.kernel.org/r/20220928070130.3657183-3-yanaijie@huawei.com
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When executing SMP task failed, the smp_execute_task_sg() calls del_timer()
to delete "slow_task->timer". However, if the timer handler
sas_task_internal_timedout() is running, the del_timer() in
smp_execute_task_sg() will not stop it and a UAF will happen. The process
is shown below:
(thread 1) | (thread 2)
smp_execute_task_sg() | sas_task_internal_timedout()
... |
del_timer() |
... | ...
sas_free_task(task) |
kfree(task->slow_task) //FREE|
| task->slow_task->... //USE
Fix by calling del_timer_sync() in smp_execute_task_sg(), which makes sure
the timer handler have finished before the "task->slow_task" is
deallocated.
Link: https://lore.kernel.org/r/20220920144213.10536-1-duoming@zju.edu.cn
Fixes: 2908d778ab3e ("[SCSI] aic94xx: new driver")
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Similarly to sas report general and discovery responses, define the
structure struct smp_rps_resp to handle SATA PHY report responses using a
structure with a size that is exactly equal to the sas defined response
size.
With this change, struct smp_resp becomes unused and is removed.
Link: https://lore.kernel.org/r/20220609022456.409087-4-damien.lemoal@opensource.wdc.com
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When compiling with gcc 12, several warnings are thrown by gcc when
compiling drivers/scsi/libsas/sas_expander.c, e.g.:
In function ‘sas_get_ex_change_count’,
inlined from ‘sas_find_bcast_dev’ at
drivers/scsi/libsas/sas_expander.c:1816:8:
drivers/scsi/libsas/sas_expander.c:1781:20: warning: array subscript
‘struct smp_resp[0]’ is partly outside array bounds of ‘unsigned
char[32]’ [-Warray-bounds]
1781 | if (rg_resp->result != SMP_RESP_FUNC_ACC) {
| ~~~~~~~^~~~~~~~
This is due to the use of the struct smp_resp to aggregate all possible
response types using a union but allocating a response buffer with a size
exactly equal to the size of the response type needed. This leads to access
to fields of struct smp_resp from an allocated memory area that is smaller
than the size of struct smp_resp.
Fix this by defining struct smp_rg_resp for sas report general responses.
Link: https://lore.kernel.org/r/20220609022456.409087-3-damien.lemoal@opensource.wdc.com
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When compiling with gcc 12, several warnings are thrown by gcc when
compiling drivers/scsi/libsas/sas_expander.c, e.g.:
In function ‘sas_get_phy_change_count’,
inlined from ‘sas_find_bcast_phy.constprop’ at
drivers/scsi/libsas/sas_expander.c:1737:9:
drivers/scsi/libsas/sas_expander.c:1697:39: warning: array subscript
‘struct smp_resp[0]’ is partly outside array bounds of ‘unsigned
char[56]’ [-Warray-bounds]
1697 | *pcc = disc_resp->disc.change_count;
| ~~~~~~~~~~~~~~~^~~~~~~~~~~~~
This is due to the use of the struct smp_resp to aggregate all possible
response types using a union but allocating a response buffer with a size
exactly equal to the size of the response type needed. This leads to access
to fields of struct smp_resp from an allocated memory area that is smaller
than the size of struct smp_resp.
Fix this by defining struct smp_disc_resp for sas discovery operations.
Since this structure and the generic struct smp_resp are identical for
the little endian and big endian archs, move the definition of these
structures at the end of include/scsi/sas.h to avoid repeating their
definition.
Link: https://lore.kernel.org/r/20220609022456.409087-2-damien.lemoal@opensource.wdc.com
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Move the SMP task handlers to the core host code as they will be re-used
for executing internal abort and TMF tasks.
Link: https://lore.kernel.org/r/1645112566-115804-7-git-send-email-john.garry@huawei.com
Tested-by: Yihang Li <liyihang6@hisilicon.com>
Tested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When sending SMP I/Os to the host we need to ensure that the host is not
suspended and can process the commands. This is a better approach than
replying on the host to resume itself to handle such commands. Use
pm_runtime_get_sync() and pm_runtime_put_sync() calls for the host when
executing SMP I/Os.
Link: https://lore.kernel.org/r/1639999298-244569-10-git-send-email-chenxiang66@hisilicon.com
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
libsas needs to include some header files in the scsi directory. However
these are currently hardcoded with the path "../" in the C files. Do this
in the Makefile to avoid hardcoding the path.
Link: https://lore.kernel.org/r/20210716074551.771312-1-yanaijie@huawei.com
Cc: John Garry <john.garry@huawei.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch prepares for converting SAM status codes into an enum. Without
this patch converting SAM status codes into an enumeration type would
trigger complaints about enum type mismatches for the SAS code.
Link: https://lore.kernel.org/r/20210524025457.11299-2-bvanassche@acm.org
Cc: Hannes Reinecke <hare@suse.com>
Cc: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Cc: Jason Yan <yanaijie@huawei.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The variable 'res' is being initialized with a value that is never read and
it is being updated later with a new value. The initialization is redundant
and can be removed.
Link: https://lore.kernel.org/r/20200722154404.959267-1-colin.king@canonical.com
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Addresses-Coverity: ("Unused value")
Currently we use a mixture of %016llx, %llx, and %16llx when printing a SAS
address.
Since the most significant nibble of the SAS address is always 5 - as per
standard - this formatting is not so important; but some fake SAS addresses
for SATA devices may not be. And we have mangled/invalid address to
consider also. And it's better to be consistent in the code, so use a fixed
format.
The SAS address is a fixed size at 64b, so we want to 0 byte extend to 16
nibbles, so use %016llx globally.
Also make some prints to be explicitly hex, and tidy some whitespace issue.
Link: https://lore.kernel.org/r/1576758957-227350-1-git-send-email-john.garry@huawei.com
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly update of the usual drivers: qla2xxx, hpsa, lpfc, ufs,
mpt3sas, ibmvscsi, megaraid_sas, bnx2fc and hisi_sas as well as the
removal of the osst driver (I heard from Willem privately that he
would like the driver removed because all his test hardware has
failed). Plus number of minor changes, spelling fixes and other
trivia.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXSTl4yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishdcxAQDCJVbd
fPUX76/V1ldupunF97+3DTharxxbst+VnkOnCwD8D4c0KFFFOI9+F36cnMGCPegE
fjy17dQLvsJ4GsidHy8=
=aS5B
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: qla2xxx, hpsa, lpfc, ufs,
mpt3sas, ibmvscsi, megaraid_sas, bnx2fc and hisi_sas as well as the
removal of the osst driver (I heard from Willem privately that he
would like the driver removed because all his test hardware has
failed). Plus number of minor changes, spelling fixes and other
trivia.
The big merge conflict this time around is the SPDX licence tags.
Following discussion on linux-next, we believe our version to be more
accurate than the one in the tree, so the resolution is to take our
version for all the SPDX conflicts"
Note on the SPDX license tag conversion conflicts: the SCSI tree had
done its own SPDX conversion, which in some cases conflicted with the
treewide ones done by Thomas & co.
In almost all cases, the conflicts were purely syntactic: the SCSI tree
used the old-style SPDX tags ("GPL-2.0" and "GPL-2.0+") while the
treewide conversion had used the new-style ones ("GPL-2.0-only" and
"GPL-2.0-or-later").
In these cases I picked the new-style one.
In a few cases, the SPDX conversion was actually different, though. As
explained by James above, and in more detail in a pre-pull-request
thread:
"The other problem is actually substantive: In the libsas code Luben
Tuikov originally specified gpl 2.0 only by dint of stating:
* This file is licensed under GPLv2.
In all the libsas files, but then muddied the water by quoting GPLv2
verbatim (which includes the or later than language). So for these
files Christoph did the conversion to v2 only SPDX tags and Thomas
converted to v2 or later tags"
So in those cases, where the spdx tag substantially mattered, I took the
SCSI tree conversion of it, but then also took the opportunity to turn
the old-style "GPL-2.0" into a new-style "GPL-2.0-only" tag.
Similarly, when there were whitespace differences or other differences
to the comments around the copyright notices, I took the version from
the SCSI tree as being the more specific conversion.
Finally, in the spdx conversions that had no conflicts (because the
treewide ones hadn't been done for those files), I just took the SCSI
tree version as-is, even if it was old-style. The old-style conversions
are perfectly valid, even if the "-only" and "-or-later" versions are
perhaps more descriptive.
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (185 commits)
scsi: qla2xxx: move IO flush to the front of NVME rport unregistration
scsi: qla2xxx: Fix NVME cmd and LS cmd timeout race condition
scsi: qla2xxx: on session delete, return nvme cmd
scsi: qla2xxx: Fix kernel crash after disconnecting NVMe devices
scsi: megaraid_sas: Update driver version to 07.710.06.00-rc1
scsi: megaraid_sas: Introduce various Aero performance modes
scsi: megaraid_sas: Use high IOPS queues based on IO workload
scsi: megaraid_sas: Set affinity for high IOPS reply queues
scsi: megaraid_sas: Enable coalescing for high IOPS queues
scsi: megaraid_sas: Add support for High IOPS queues
scsi: megaraid_sas: Add support for MPI toolbox commands
scsi: megaraid_sas: Offload Aero RAID5/6 division calculations to driver
scsi: megaraid_sas: RAID1 PCI bandwidth limit algorithm is applicable for only Ventura
scsi: megaraid_sas: megaraid_sas: Add check for count returned by HOST_DEVICE_LIST DCMD
scsi: megaraid_sas: Handle sequence JBOD map failure at driver level
scsi: megaraid_sas: Don't send FPIO to RL Bypass queue
scsi: megaraid_sas: In probe context, retry IOC INIT once if firmware is in fault
scsi: megaraid_sas: Release Mutex lock before OCR in case of DCMD timeout
scsi: megaraid_sas: Call disable_irq from process IRQ poll
scsi: megaraid_sas: Remove few debug counters from IO path
...
Many times in libsas, and in LLDDs which use libsas, the check for an
expander device is re-implemented or open coded.
Use dev_is_expander() instead. We rename this from
sas_dev_type_is_expander() to not spill so many lines in referencing.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since we are processing events synchronously now, the second call of
sas_ex_join_wide_port() in sas_ex_discover_dev() is not needed. There will
be no races with other works in disco workqueue. So remove the second
sas_ex_join_wide_port().
I did not change the return value of 'res' to error when discover failed
because we need to continue to discover other phys if one phy discover
failed. So let's keep that logic as before and just add a debug log to
detect the failure. And directly return if second fanout expander attatched
to the parent expander because it has nothing to do after the phy is
disabled.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the the GPLv2 SPDX tag instead of verbose boilerplate text.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently we print expander PHY indexes in a mix of decimal and hex.
It is more consistent and also more convenient to read decimal, so
make this change.
We use width of 2 for expander and 1 for root PHYs prints.
Some lines which were needlessly spilling multiple lines are unified.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When we discover the PHY is empty in sas_rediscover_dev(), the PHY
information (like negotiated linkrate) is not updated.
As such, for a user examining sysfs for that PHY, they would see
incorrect values:
root@(none)$ cd /sys/class/sas_phy/phy-0:0:20
root@(none)$ more negotiated_linkrate
3.0 Gbit
root@(none)$ echo 0 > enable
root@(none)$ more negotiated_linkrate
3.0 Gbit
So fix this, simply discover the PHY again, even though we know it's empty;
in the above example, this gives us:
root@(none)$ more negotiated_linkrate
Phy disabled
We must do this after unregistering the device associated with the PHY
(in sas_unregister_devs_sas_addr()).
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When an expander PHY which was part of a wideport disconnects, we would see
a log like this from sas_rediscover():
[ 39.695554] sas: phy20 part of wide port with phy16
Here, phy20 is the PHY that disconnected, and phy16 is the lowest indexed
member PHY of the wideport.
The log implies the phy20 is still part of the wideport with phy16, so is
misleading or, at least, vague.
Improve the logs in SAS rediscovery by removing this log and adding a log
in sas_rediscover_dev() to tell what's really going on.
While we're at it, also make the logs in sas_find_bcast_dev() more
informative (and more consistent with the reset of the expander logs).
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently for fixing the linkrate matching during discovery such that the
linkrate of a SATA PHY does not exceed min pathway to initiator, we set the
SATA PHY programmed min linkrate to the same value as the programmed max
linkrate.
This is unnecessary, and we should be able to keep the same programmed min
linkrate if it is already lower than this new max programmed linkrate.
This patch makes that change.
In effect, this will not make much difference since we generally will
negotiate a linkrate at the programmed max linkrate, and the programmed min
linkrate will have no impact.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Many times we use 8 for SAS address length, while we already have a macro
for this - SAS_ADDR_SIZE.
Replace instances of this with the macro. However, don't touch the SAS
address array sizes sas.h, as these are defined according to the SAS spec.
Some missing whitespaces are also added, and whitespace indentation
in sas_hash_addr() is also fixed (see sas_hash_addr()).
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly update of the usual drivers: arcmsr, qla2xxx, lpfc,
hisi_sas, target/iscsi and target/core. Additionally Christoph
refactored gdth as part of the dma changes. The major mid-layer
change this time is the removal of bidi commands and with them the
whole of the osd/exofs driver and filesystem.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXIC54SYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishT1GAPwJEV23
ExPiPsnuVgKj49nLTagZ3rILRQcYNbL+MNYqxQEA0cT8FHzSDBfWY5OKPNE+RQ8z
f69LpXGmMpuagKGvvd4=
=Fhy1
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: arcmsr, qla2xxx, lpfc,
hisi_sas, target/iscsi and target/core.
Additionally Christoph refactored gdth as part of the dma changes. The
major mid-layer change this time is the removal of bidi commands and
with them the whole of the osd/exofs driver and filesystem. This is a
major simplification for block and mq in particular"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (240 commits)
scsi: cxgb4i: validate tcp sequence number only if chip version <= T5
scsi: cxgb4i: get pf number from lldi->pf
scsi: core: replace GFP_ATOMIC with GFP_KERNEL in scsi_scan.c
scsi: mpt3sas: Add missing breaks in switch statements
scsi: aacraid: Fix missing break in switch statement
scsi: kill command serial number
scsi: csiostor: drop serial_number usage
scsi: mvumi: use request tag instead of serial_number
scsi: dpt_i2o: remove serial number usage
scsi: st: osst: Remove negative constant left-shifts
scsi: ufs-bsg: Allow reading descriptors
scsi: ufs: Allow reading descriptor via raw upiu
scsi: ufs-bsg: Change the calling convention for write descriptor
scsi: ufs: Remove unused device quirks
Revert "scsi: ufs: disable vccq if it's not needed by UFS device"
scsi: megaraid_sas: Remove a bunch of set but not used variables
scsi: clean obsolete return values of eh_timed_out
scsi: sd: Optimal I/O size should be a multiple of physical block size
scsi: MAINTAINERS: SCSI initiator and target tweaks
scsi: fcoe: make use of fip_mode enum complete
...
Since the function scsi_to_u32() is identical to get_unaligned_be32(),
change all scsi_to_u32() calls into get_unaligned_be32() calls.
Cc: Jian Luo <luojian5@huawei.com>
Cc: John Garry <john.garry@huawei.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
+----------+ +----------+
| | | |
| |--- 3.0 G ---| |--- 6.0 G --- SAS disk
| | | |
| |--- 3.0 G ---| |--- 6.0 G --- SAS disk
|initiator | | |
| device |--- 3.0 G ---| Expander |--- 6.0 G --- SAS disk
| | | |
| |--- 3.0 G ---| |--- 6.0 G --- SATA disk -->failed to connect
| | | |
| | | |--- 6.0 G --- SATA disk -->failed to connect
| | | |
+----------+ +----------+
According to Serial Attached SCSI - 1.1 (SAS-1.1):
If an expander PHY attached to a SATA PHY is using a physical link rate
greater than the maximum connection rate supported by the pathway from an
STP initiator port, a management application client should use the SMP PHY
CONTROL function (see 10.4.3.10) to set the PROGRAMMED MAXIMUM PHYSICAL
LINK RATE field of the expander PHY to the maximum connection rate
supported by the pathway from that STP initiator port.
Currently libsas does not support checking if this condition occurs, nor
rectifying when it does.
Such a condition is not at all common, however it has been seen on some
pre-silicon environments where the initiator PHY only supports a 1.5 Gbit
maximum linkrate, mated with 12G expander PHYs and 3/6G SATA phy.
This patch adds support for checking and rectifying this condition during
initial device discovery only.
We do support checking min pathway connection rate during revalidation phase,
when new devices can be detected in the topology. However we do not
support in the case of the the user reprogramming PHY linkrates, such that
min pathway condition is not met/maintained.
A note on root port PHY rates:
The libsas root port PHY rates calculation is broken. Libsas sets the
rates (min, max, and current linkrate) of a root port to the same linkrate
of the first PHY member of that same port. In doing so, it assumes that
all other PHYs which subsequently join the port to have the same
negotiated linkrate, when they could actually be different.
In practice this doesn't happen, as initiator and expander PHYs are
normally initialised with consistent min/max linkrates.
This has not caused an issue so far, so leave alone for now.
Tested-by: Jian Luo <luojian5@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the SMP PHY control execution result is checked, however the
function result for the command is not.
As such, we may be missing all potential errors, like SMP FUNCTION FAILED,
INVALID REQUEST FRAME LENGTH, etc., meaning the PHY control request has
failed.
In some scenarios we need to ensure the function result is accepted, so add
a check for this.
Tested-by: Jian Luo <luojian5@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Like sas_printk() did previously, SAS_DPRINTK() offers little value now
that libsas logs already have the "sas" prefix through pr_fmt(fmt). So it
can be dropped.
However, after reviewing some logs in libsas, it is noticed that debug
level is too low in many instances.
So this change drops SAS_DPRINTK() and revises some logs to a more
appropriate level. However many stay at debug level, although some
are significantly promoted.
We add -DDEBUG for compilation so that we keep the debug messages by
default, as before.
All the pre-existing checkpatch errors for spanning messages across
multiple lines are also fixed.
Finally, all other references to printk() [apart from special formatting
in sas_ata.c] are removed and replaced with appropriate pr_xxx().
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The printk wrapper sas_printk() adds little value now that libsas logs
already have the "sas" prefix through pr_fmt(fmt), so just use pr_notice()
directly.
In addition, strings which span multiple lines are reunited.
Originally-from: Joe Perches <joe@perches.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the lldd is processing the complete sas task in interrupt and set the
task stat as SAS_TASK_STATE_DONE, the smp timeout timer is able to be
triggered at the same time. And smp_task_timedout() will complete the task
wheter the SAS_TASK_STATE_DONE is set or not. Then the sas task may freed
before lldd end the interrupt process. Thus a use-after-free will happen.
Fix this by calling the complete() only when SAS_TASK_STATE_DONE is not
set. And remove the check of the return value of the del_timer(). Once the
LLDD sets DONE, it must call task->done(), which will call
smp_task_done()->complete() and the task will be completed and freed
correctly.
Reported-by: chenxiang <chenxiang66@hisilicon.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
CC: John Garry <john.garry@huawei.com>
CC: Johannes Thumshirn <jthumshirn@suse.de>
CC: Ewan Milne <emilne@redhat.com>
CC: Christoph Hellwig <hch@lst.de>
CC: Tomas Henzl <thenzl@redhat.com>
CC: Dan Williams <dan.j.williams@intel.com>
CC: Hannes Reinecke <hare@suse.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If we went into sas_rediscover_dev() the attached_sas_addr was already insured
not to be zero. So it's unnecessary to check if the attached_sas_addr is zero.
And although if the sas address is not changed, we always have to unregister
the old device when we are going to register a new one. We cannot just leave
the device there and bring up the new.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
CC: chenxiang <chenxiang66@hisilicon.com>
CC: John Garry <john.garry@huawei.com>
CC: Johannes Thumshirn <jthumshirn@suse.de>
CC: Ewan Milne <emilne@redhat.com>
CC: Christoph Hellwig <hch@lst.de>
CC: Tomas Henzl <thenzl@redhat.com>
CC: Dan Williams <dan.j.williams@intel.com>
CC: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Avoid that building with W=1 causes the kernel-doc tool to complain
about function arguments that have not been documented in the libsas
kernel-doc headers. Avoid that the short description starts with a
hyphen by changing "--" into "-" in the first line of the kernel-doc
headers.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: John Garry <john.garry@huawei.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly updates of the usual driver suspects: arcmsr,
scsi_debug, mpt3sas, lpfc, cxlflash, qla2xxx, aacraid, megaraid_sas,
hisi_sas. We also have a rework of the libsas hotplug handling to
make it more robust, a slew of 32 bit time conversions and fixes, and
a host of the usual minor updates and style changes. The biggest
potential for regressions is the libsas hotplug changes, but so far
they seem stable under testing.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCWnH+5SYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishWxuAP0UvuJp
MNR/yU/wv/emSzOc48Ldwd7I0xD2XxSnloGUgwD+IGZZT5yNUQA1THCbm+en4hkB
WvyBieQs9qRit+2czd4=
=gJMf
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates of the usual driver suspects: arcmsr,
scsi_debug, mpt3sas, lpfc, cxlflash, qla2xxx, aacraid, megaraid_sas,
hisi_sas.
We also have a rework of the libsas hotplug handling to make it more
robust, a slew of 32 bit time conversions and fixes, and a host of the
usual minor updates and style changes. The biggest potential for
regressions is the libsas hotplug changes, but so far they seem stable
under testing"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (313 commits)
scsi: qla2xxx: Fix logo flag for qlt_free_session_done()
scsi: arcmsr: avoid do_gettimeofday
scsi: core: Add VENDOR_SPECIFIC sense code definitions
scsi: qedi: Drop cqe response during connection recovery
scsi: fas216: fix sense buffer initialization
scsi: ibmvfc: Remove unneeded semicolons
scsi: hisi_sas: fix a bug in hisi_sas_dev_gone()
scsi: hisi_sas: directly attached disk LED feature for v2 hw
scsi: hisi_sas: devicetree: bindings: add LED feature for v2 hw
scsi: megaraid_sas: NVMe passthrough command support
scsi: megaraid: use ktime_get_real for firmware time
scsi: fnic: use 64-bit timestamps
scsi: qedf: Fix error return code in __qedf_probe()
scsi: devinfo: fix format of the device list
scsi: qla2xxx: Update driver version to 10.00.00.05-k
scsi: qla2xxx: Add XCB counters to debugfs
scsi: qla2xxx: Fix queue ID for async abort with Multiqueue
scsi: qla2xxx: Fix warning for code intentation in __qla24xx_handle_gpdb_event()
scsi: qla2xxx: Fix warning during port_name debug print
scsi: qla2xxx: Fix warning in qla2x00_async_iocb_timeout()
...
In commit 87c8331fcf72 ("[SCSI] libsas: prevent domain rediscovery
competing with ata error handling") introduced disco mutex to prevent
rediscovery competing with ata error handling and put the whole
revalidation in the mutex. But the rphy add/remove needs to wait for the
error handling which also grabs the disco mutex. This may leads to dead
lock.So the probe and destruct event were introduce to do the rphy
add/remove asynchronously and out of the lock.
The asynchronously processed workers makes the whole discovery process
not atomic, the other events may interrupt the process. For example,
if a loss of signal event inserted before the probe event, the
sas_deform_port() is called and the port will be deleted.
And sas_port_delete() may run before the destruct event, but the
port-x:x is the top parent of end device or expander. This leads to
a kernel WARNING such as:
[ 82.042979] sysfs group 'power' not found for kobject 'phy-1:0:22'
[ 82.042983] ------------[ cut here ]------------
[ 82.042986] WARNING: CPU: 54 PID: 1714 at fs/sysfs/group.c:237
sysfs_remove_group+0x94/0xa0
[ 82.043059] Call trace:
[ 82.043082] [<ffff0000082e7624>] sysfs_remove_group+0x94/0xa0
[ 82.043085] [<ffff00000864e320>] dpm_sysfs_remove+0x60/0x70
[ 82.043086] [<ffff00000863ee10>] device_del+0x138/0x308
[ 82.043089] [<ffff00000869a2d0>] sas_phy_delete+0x38/0x60
[ 82.043091] [<ffff00000869a86c>] do_sas_phy_delete+0x6c/0x80
[ 82.043093] [<ffff00000863dc20>] device_for_each_child+0x58/0xa0
[ 82.043095] [<ffff000008696f80>] sas_remove_children+0x40/0x50
[ 82.043100] [<ffff00000869d1bc>] sas_destruct_devices+0x64/0xa0
[ 82.043102] [<ffff0000080e93bc>] process_one_work+0x1fc/0x4b0
[ 82.043104] [<ffff0000080e96c0>] worker_thread+0x50/0x490
[ 82.043105] [<ffff0000080f0364>] kthread+0xfc/0x128
[ 82.043107] [<ffff0000080836c0>] ret_from_fork+0x10/0x50
Make probe and destruct a direct call in the disco and revalidate function,
but put them outside the lock. The whole discovery or revalidate won't
be interrupted by other events. And the DISCE_PROBE and DISCE_DESTRUCT
event are deleted as a result of the direct call.
Introduce a new list to destruct the sas_port and put the port delete after
the destruct. This makes sure the right order of destroying the sysfs
kobject and fix the warning above.
In sas_ex_revalidate_domain() have a loop to find all broadcasted
device, and sometimes we have a chance to find the same expander twice.
Because the sas_port will be deleted at the end of the whole revalidate
process, sas_port with the same name cannot be added before this.
Otherwise the sysfs will complain of creating duplicate filename. Since
the LLDD will send broadcast for every device change, we can only
process one expander's revalidation.
[mkp: kbuild test robot warning]
Signed-off-by: Jason Yan <yanaijie@huawei.com>
CC: John Garry <john.garry@huawei.com>
CC: Johannes Thumshirn <jthumshirn@suse.de>
CC: Ewan Milne <emilne@redhat.com>
CC: Christoph Hellwig <hch@lst.de>
CC: Tomas Henzl <thenzl@redhat.com>
CC: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The status of SAS PHY is in sas_phy->enabled. There is an issue that the
status of a remote SAS PHY may be initialized incorrectly: if disable
remote SAS PHY through sysfs interface (such as echo 0 >
/sys/class/sas_phy/phy-1:0:0/enable), then reboot the system, and we
will find the status of remote SAS PHY which is disabled before is
1 (cat /sys/class/sas_phy/phy-1:0:0/enable). But actually the status of
remote SAS PHY is disabled and the device attached is not found.
In SAS protocol, NEGOTIATED LOGICAL LINK RATE field of DISCOVER response
is 0x1 when remote SAS PHY is disabled. So initialize sas_phy->enabled
according to the value of NEGOTIATED LOGICAL LINK RATE field.
Signed-off-by: chenxiang <chenxiang66@hisilicon.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The intend purpose here was to goto out if smp_execute_task() returned
error. Obviously something got screwed up. We will never get these link
error statistics below:
~:/sys/class/sas_phy/phy-1:0:12 # cat invalid_dword_count
0
~:/sys/class/sas_phy/phy-1:0:12 # cat running_disparity_error_count
0
~:/sys/class/sas_phy/phy-1:0:12 # cat loss_of_dword_sync_count
0
~:/sys/class/sas_phy/phy-1:0:12 # cat phy_reset_problem_count
0
Obviously we should goto error handler if smp_execute_task() returns
non-zero.
Fixes: 2908d778ab3e ("[SCSI] aic94xx: new driver")
Signed-off-by: Jason Yan <yanaijie@huawei.com>
CC: John Garry <john.garry@huawei.com>
CC: chenqilin <chenqilin2@huawei.com>
CC: chenxiang <chenxiang66@hisilicon.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We've got a memory leak with the following producer:
while true;
do cat /sys/class/sas_phy/phy-1:0:12/invalid_dword_count >/dev/null;
done
The buffer req is allocated and not freed after we return. Fix it.
Fixes: 2908d778ab3e ("[SCSI] aic94xx: new driver")
Signed-off-by: Jason Yan <yanaijie@huawei.com>
CC: John Garry <john.garry@huawei.com>
CC: chenqilin <chenqilin2@huawei.com>
CC: chenxiang <chenxiang66@hisilicon.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The most important one is the bfa fix because it's easy to oops the
kernel with this driver (this includes the commit that corrects the
compiler warning in the original), a regression in the new timespec
conversion in aacraid and a regression in the Fibre Channel ELS
handling patch. The other three are a theoretical problem with
termination in the vendor/host matching code and a use after free in
lpfc.
The additional patches are a fix for an I/O hang in the mq code under
certain circumstances and a rare oops in some debugging code.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=9sav
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"The most important one is the bfa fix because it's easy to oops the
kernel with this driver (this includes the commit that corrects the
compiler warning in the original), a regression in the new timespec
conversion in aacraid and a regression in the Fibre Channel ELS
handling patch.
The other three are a theoretical problem with termination in the
vendor/host matching code and a use after free in lpfc.
The additional patches are a fix for an I/O hang in the mq code under
certain circumstances and a rare oops in some debugging code"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: core: Fix a scsi_show_rq() NULL pointer dereference
scsi: MAINTAINERS: change FCoE list to linux-scsi
scsi: libsas: fix length error in sas_smp_handler()
scsi: bfa: fix type conversion warning
scsi: core: run queue if SCSI device queue isn't ready and queue is idle
scsi: scsi_devinfo: cleanly zero-pad devinfo strings
scsi: scsi_devinfo: handle non-terminated strings
scsi: bfa: fix access to bfad_im_port_s
scsi: aacraid: address UBSAN warning regression
scsi: libfc: fix ELS request handling
scsi: lpfc: Use after free in lpfc_rq_buf_free()
The return value of smp_execute_task_sg() is the untransferred residual,
but bsg_job_done() requires the length of payload received. This makes
SMP passthrough commands from userland by sg ioctl to libsas get a wrong
response. The userland tools such as smp_utils failed because of these
wrong responses:
~#smp_discover /dev/bsg/expander-2\:13
response too short, len=0
~#smp_discover /dev/bsg/expander-2\:134
response too short, len=0
Fix this by passing the actual received length to bsg_job_done(). And if
smp_execute_task_sg() returns 0, this means received length is exactly
the buffer length.
[mkp: typo]
Fixes: 651a01364994 ("scsi: scsi_transport_sas: switch to bsg-lib for SMP passthrough")
Cc: <stable@vger.kernel.org> # v4.14+
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Reported-by: chenqilin <chenqilin2@huawei.com>
Tested-by: chenqilin <chenqilin2@huawei.com>
CC: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With all callbacks converted, and the timer callback prototype
switched over, the TIMER_FUNC_TYPE cast is no longer needed,
so remove it. Conversion was done with the following scripts:
perl -pi -e 's|\(TIMER_FUNC_TYPE\)||g' \
$(git grep TIMER_FUNC_TYPE | cut -d: -f1 | sort -u)
perl -pi -e 's|\(TIMER_DATA_TYPE\)||g' \
$(git grep TIMER_DATA_TYPE | cut -d: -f1 | sort -u)
The now unused macros are also dropped from include/linux/timer.h.
Signed-off-by: Kees Cook <keescook@chromium.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. This requires adding a pointer to
hold the timer's target task, as there isn't a link back from slow_task.
Cc: John Garry <john.garry@huawei.com>
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Jack Wang <jinpu.wang@profitbricks.com>
Cc: lindar_liu@usish.com
Cc: Jens Axboe <axboe@fb.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Benjamin Block <bblock@linux.vnet.ibm.com>
Cc: Baoyou Xie <baoyou.xie@linaro.org>
Cc: Wei Yongjun <weiyongjun1@huawei.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: John Garry <john.garry@huawei.com> # for hisi_sas part
Tested-by: John Garry <john.garry@huawei.com> # basic sanity test for hisi_sas
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Simplify the SMP passthrough code by switching it to the generic bsg-lib
helpers that abstract away the details of the request code, and gets
drivers out of seeing struct scsi_request.
For the libsas host SMP code there is a small behavior difference in
that we now always clear the residual len for successful commands,
similar to the three other SMP handler implementations. Given that
there is no partial command handling in the host SMP handler this should
not matter in practice.
[mkp: typos and checkpatch fixes]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
And require all drivers that want to support BLOCK_PC to allocate it
as the first thing of their private data. To support this the legacy
IDE and BSG code is switched to set cmd_size on their queues to let
the block layer allocate the additional space.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
The task_collector mode (or "latency_injector", (C) Dan Willians) is an
optional I/O path in libsas that queues up scsi commands instead of
directly sending it to the hardware. It generall increases latencies
to in the optiomal case slightly reduce mmio traffic to the hardware.
Only the obsolete aic94xx driver and the mvsas driver allowed to use
it without recompiling the kernel, and most drivers didn't support it
at all.
Remove the giant blob of code to allow better optimizations for scsi-mq
in the future.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
