After searching for a protocol handler in dev_gro_receive, checking for
failure is redundant. Skip the failure code after finding the
corresponding handler.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Richard Gobert <richardbgobert@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20221108123320.GA59373@debian
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Russell King says:
====================
Clean up pcs-xpcs accessors
This series cleans up the pcs-xpcs code to use mdiodev accessors for
read/write just like xpcs_modify_changed() does. In order to do this,
we need to introduce the mdiodev clause 45 accessors.
====================
Link: https://lore.kernel.org/r/Y2pm13+SDg6N/IVx@shell.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use mdiodev accessors rather than accessing the bus and address in
the mdio_device structure and using the mdiobus accessors.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The strlen() may go too far when estimating the length of
the given string. In some cases it may go over the boundary
and crash the system which is the case according to the commit
13a55372b6 ("ARM: orion5x: Revert commit 4904dbda41c8.").
Rectify this by switching to strnlen() for the expected
maximum length of the string.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221108141108.62974-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The existing genphy_loopback() is not working for TI DP83867 PHY as it
will disable autoneg support while another side is still enabling autoneg.
This is causing the link is not established and results in timeout error
in genphy_loopback() function.
Thus, based on TI PHY datasheet, introduce a TI PHY loopback function by
just configuring BMCR_LOOPBACK(Bit-9) in MII_BMCR register (0x0).
Tested working on TI DP83867 PHY for all speeds (10/100/1000Mbps).
Signed-off-by: Tan Tee Min <tee.min.tan@linux.intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20221108101527.612723-1-michael.wei.hong.sit@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Raju Lakkaraju says:
====================
net: lan743x: PCI11010 / PCI11414 devices Enhancements
This patch series continues with the addition of supported features for the
Ethernet function of the PCI11010 / PCI11414 devices to the LAN743x driver.
====================
Link: https://lore.kernel.org/r/20221107085650.991470-1-Raju.Lakkaraju@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Test that locked bridge port configurations that are not supported by
mlxsw are rejected.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Test that packets received via a locked bridge port whose {SMAC, VID}
does not appear in the bridge's FDB or appears with a different port,
trigger the "locked_port" packet trap.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Test that packets with a destination MAC of 01:80:C2:00:00:03 trigger
the "eapol" packet trap.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Merely checking whether a trap counter incremented or not without
logging a test result is useful on its own. Split this functionality to
a helper which will be used by subsequent patches.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add locked bridge port support by reacting to changes in the
'BR_PORT_LOCKED' flag. When set, enable security checks on the local
port via the previously added SPFSR register.
When security checks are enabled, an incoming packet will trigger an FDB
lookup with the packet's source MAC and the FID it was classified to. If
an FDB entry was not found or was found to be pointing to a different
port, the packet will be dropped. Such packets increment the
"discard_ingress_general" ethtool counter. For added visibility, user
space can trap such packets to the CPU by enabling the "locked_port"
trap. Example:
# devlink trap set pci/0000:06:00.0 trap locked_port action trap
Unlike other configurations done via bridge port flags (e.g., learning,
flooding), security checks are enabled in the device on a per-port basis
and not on a per-{port, VLAN} basis. As such, scenarios where user space
can configure different locking settings for different VLANs configured
on a port need to be vetoed. To that end, veto the following scenarios:
1. Locking is set on a bridge port that is a VLAN upper
2. Locking is set on a bridge port that has VLAN uppers
3. VLAN upper is configured on a locked bridge port
Examples:
# bridge link set dev swp1.10 locked on
Error: mlxsw_spectrum: Locked flag cannot be set on a VLAN upper.
# ip link add link swp1 name swp1.10 type vlan id 10
# bridge link set dev swp1 locked on
Error: mlxsw_spectrum: Locked flag cannot be set on a bridge port that has VLAN uppers.
# bridge link set dev swp1 locked on
# ip link add link swp1 name swp1.10 type vlan id 10
Error: mlxsw_spectrum: VLAN uppers are not supported on a locked port.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Propagate extack to mlxsw_sp_port_attr_br_pre_flags_set() in order to
communicate error messages related to bridge port flag validation.
Example:
# bridge link set dev swp1 locked on
Error: mlxsw_spectrum: Unsupported bridge port flag.
More error messages will be added in subsequent patches.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In Spectrum, learning happens in parallel to the security checks.
Therefore, regardless of the result of the security checks, a learning
notification will be generated by the device and polled later on by the
driver.
Currently, the driver reacts to learning notifications by programming
corresponding FDB entries to the device. When a port is locked (i.e.,
has security checks enabled), this can no longer happen, as otherwise
any host will blindly gain authorization.
Instead, notify the learned entry as a locked entry to the bridge driver
that will in turn notify it to user space, in case MAB is enabled. User
space can then decide to authorize the host by clearing the "locked"
flag, which will cause the entry to be programmed to the device.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Subsequent patches will need to report locked FDB entries to the bridge
driver. Prepare for that by adding a 'locked' argument to
mlxsw_sp_fdb_call_notifiers() according to which the 'locked' bit is set
in the FDB notification info. For now, always pass 'false'.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add an API to enable or disable security checks on a local port. It will
be used by subsequent patches when the 'BR_PORT_LOCKED' flag is toggled.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the Switch Port FDB Security Register (SPFSR) that allows enabling
and disabling security checks on a given local port. In Linux terms, it
allows locking / unlocking a port.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Register the previously added packet traps with devlink. This allows
user space to tune their policers and in the case of the locked port
trap, user space can set its action to "trap" in order to gain
visibility into packets that were discarded by the device due to the
locked port check failure.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add packet traps for 802.1X operation. The "eapol" control trap is used
to trap EAPOL packets and is required for the correct operation of the
control plane. The "locked_port" drop trap can be enabled to gain
visibility into packets that were dropped by the device due to the
locked bridge port check.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reflect the 'BR_PORT_MAB' flag to device drivers so that:
* Drivers that support MAB could act upon the flag being toggled.
* Drivers that do not support MAB will prevent MAB from being enabled.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the bridge is offloaded to hardware, FDB entries are learned and
aged-out by the hardware. Some device drivers synchronize the hardware
and software FDBs by generating switchdev events towards the bridge.
When a port is locked, the hardware must not learn autonomously, as
otherwise any host will blindly gain authorization. Instead, the
hardware should generate events regarding hosts that are trying to gain
authorization and their MAC addresses should be notified by the device
driver as locked FDB entries towards the bridge driver.
Allow device drivers to notify the bridge driver about such entries by
extending the 'switchdev_notifier_fdb_info' structure with the 'locked'
bit. The bit can only be set by device drivers and not by the bridge
driver.
Prevent a locked entry from being installed if MAB is not enabled on the
bridge port.
If an entry already exists in the bridge driver, reject the locked entry
if the current entry does not have the "locked" flag set or if it points
to a different port. The same semantics are implemented in the software
data path.
Signed-off-by: Hans J. Schultz <netdev@kapio-technology.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, FDB entries that are notified to the bridge via
'SWITCHDEV_FDB_ADD_TO_BRIDGE' are always marked as offloaded. With MAB
enabled, this will no longer be universally true. Device drivers will
report locked FDB entries to the bridge to let it know that the
corresponding hosts required authorization, but it does not mean that
these entries are necessarily programmed in the underlying hardware.
Solve this by determining the offload indication based of the
'offloaded' bit in the FDB notification.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jiri Pirko says:
====================
net: devlink: move netdev notifier block to dest namespace during reload
Patch #1 is just a dependency of patch #2, which is the actual fix.
====================
Link: https://lore.kernel.org/r/20221108132208.938676-1-jiri@resnulli.us
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The notifier block tracking netdev changes in devlink is registered
during devlink_alloc() per-net, it is then unregistered
in devlink_free(). When devlink moves from net namespace to another one,
the notifier block needs to move along.
Fix this by adding forgotten call to move the block.
Reported-by: Ido Schimmel <idosch@idosch.org>
Fixes: 02a68a47ea ("net: devlink: track netdev with devlink_port assigned")
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, net_dev() netdev notifier variant follows the netdev with
per-net notifier from namespace to namespace. This is implemented
by move_netdevice_notifiers_dev_net() helper.
For devlink it is needed to re-register per-net notifier during
devlink reload. Introduce a new helper called
move_netdevice_notifier_net() and share the unregister/register code
with existing move_netdevice_notifiers_dev_net() helper.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The return value from genl_op_iter_init() only tells us if
there are any policies but to begin the iteration (and therefore
load the first entry) we need to call genl_op_iter_next().
Note that it's safe to call genl_op_iter_next() on a family
with no ops, it will just return false.
This may lead to various crashes, a warning in
netlink_policy_dump_get_policy_idx() when policy is not found
or.. no problem at all if the kmalloc'ed memory happens to be
zeroed.
Fixes: b502b3185c ("genetlink: use iterator in the op to policy map dumping")
Link: https://lore.kernel.org/r/20221108204128.330287-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=q04p
-----END PGP SIGNATURE-----
Merge tag 'rxrpc-next-20221108' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
rxrpc changes
David Howells says:
====================
rxrpc: Increasing SACK size and moving away from softirq, part 1
AF_RXRPC has some issues that need addressing:
(1) The SACK table has a maximum capacity of 255, but for modern networks
that isn't sufficient. This is hard to increase in the upstream code
because of the way the application thread is coupled to the softirq
and retransmission side through a ring buffer. Adjustments to the rx
protocol allows a capacity of up to 8192, and having a ring
sufficiently large to accommodate that would use an excessive amount
of memory as this is per-call.
(2) Processing ACKs in softirq mode causes the ACKs get conflated, with
only the most recent being considered. Whilst this has the upside
that the retransmission algorithm only needs to deal with the most
recent ACK, it causes DATA transmission for a call to be very bursty
because DATA packets cannot be transmitted in softirq mode. Rather
transmission must be delegated to either the application thread or a
workqueue, so there tend to be sudden bursts of traffic for any
particular call due to scheduling delays.
(3) All crypto in a single call is done in series; however, each DATA
packet is individually encrypted so encryption and decryption of large
calls could be parallelised if spare CPU resources are available.
This is the first of a number of sets of patches that try and address them.
The overall aims of these changes include:
(1) To get rid of the TxRx ring and instead pass the packets round in
queues (eg. sk_buff_head). On the Tx side, each ACK packet comes with
a SACK table that can be parsed as-is, so there's no particular need
to maintain our own; we just have to refer to the ACK.
On the Rx side, we do need to maintain a SACK table with one bit per
entry - but only if packets go missing - and we don't want to have to
perform a complex transformation to get the information into an ACK
packet.
(2) To try and move almost all processing of received packets out of the
softirq handler and into a high-priority kernel I/O thread. Only the
transferral of packets would be left there. I would still use the
encap_rcv hook to receive packets as there's a noticeable performance
drop from letting the UDP socket put the packets into its own queue
and then getting them out of there.
(3) To make the I/O thread also do all the transmission. The app thread
would be responsible for packaging the data into packets and then
buffering them for the I/O thread to transmit. This would make it
easier for the app thread to run ahead of the I/O thread, and would
mean the I/O thread is less likely to have to wait around for a new
packet to come available for transmission.
(4) To logically partition the socket/UAPI/KAPI side of things from the
I/O side of things. The local endpoint, connection, peer and call
objects would belong to the I/O side. The socket side would not then
touch the private internals of calls and suchlike and would not change
their states. It would only look at the send queue, receive queue and
a way to pass a message to cause an abort.
(5) To remove as much locking, synchronisation, barriering and atomic ops
as possible from the I/O side. Exclusion would be achieved by
limiting modification of state to the I/O thread only. Locks would
still need to be used in communication with the UDP socket and the
AF_RXRPC socket API.
(6) To provide crypto offload kernel threads that, when there's slack in
the system, can see packets that need crypting and provide
parallelisation in dealing with them.
(7) To remove the use of system timers. Since each timer would then send
a poke to the I/O thread, which would then deal with it when it had
the opportunity, there seems no point in using system timers if,
instead, a list of timeouts can be sensibly consulted. An I/O thread
only then needs to schedule with a timeout when it is idle.
(8) To use zero-copy sendmsg to send packets. This would make use of the
I/O thread being the sole transmitter on the socket to manage the
dead-reckoning sequencing of the completion notifications. There is a
problem with zero-copy, though: the UDP socket doesn't handle running
out of option memory very gracefully.
With regard to this first patchset, the changes made include:
(1) Some fixes, including a fallback for proc_create_net_single_write(),
setting ack.bufferSize to 0 in ACK packets and a fix for rxrpc
congestion management, which shouldn't be saving the cwnd value
between calls.
(2) Improvements in rxrpc tracepoints, including splitting the timer
tracepoint into a set-timer and a timer-expired trace.
(3) Addition of a new proc file to display some stats.
(4) Some code cleanups, including removing some unused bits and
unnecessary header inclusions.
(5) A change to the recently added UDP encap_err_rcv hook so that it has
the same signature as {ip,ipv6}_icmp_error(), and then just have rxrpc
point its UDP socket's hook directly at those.
(6) Definition of a new struct, rxrpc_txbuf, that is used to hold
transmissible packets of DATA and ACK type in a single 2KiB block
rather than using an sk_buff. This allows the buffer to be on a
number of queues simultaneously more easily, and also guarantees that
the entire block is in a single unit for zerocopy purposes and that
the data payload is aligned for in-place crypto purposes.
(7) ACK txbufs are allocated at proposal and queued for later transmission
rather than being stored in a single place in the rxrpc_call struct,
which means only a single ACK can be pending transmission at a time.
The queue is then drained at various points. This allows the ACK
generation code to be simplified.
(8) The Rx ring buffer is removed. When a jumbo packet is received (which
comprises a number of ordinary DATA packets glued together), it used
to be pointed to by the ring multiple times, with an annotation in a
side ring indicating which subpacket was in that slot - but this is no
longer possible. Instead, the packet is cloned once for each
subpacket, barring the last, and the range of data is set in the skb
private area. This makes it easier for the subpackets in a jumbo
packet to be decrypted in parallel.
(9) The Tx ring buffer is removed. The side annotation ring that held the
SACK information is also removed. Instead, in the event of packet
loss, the SACK data attached an ACK packet is parsed.
(10) Allocate an skcipher request when needed in the rxkad security class
rather than caching one in the rxrpc_call struct. This deals with a
race between externally-driven call disconnection getting rid of the
skcipher request and sendmsg/recvmsg trying to use it because they
haven't seen the completion yet. This is also needed to support
parallelisation as the skcipher request cannot be used by two or more
threads simultaneously.
(11) Call udp_sendmsg() and udpv6_sendmsg() directly rather than going
through kernel_sendmsg() so that we can provide our own iterator
(zerocopy explicitly doesn't work with a KVEC iterator). This also
lets us avoid the overhead of the security hook.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow a network interface to be renamed when the interface
is up.
As described in the netconsole documentation [1], when netconsole is
used as a built-in, it will bring up the specified interface as soon as
possible. As a result, user space will not be able to rename the
interface since the kernel disallows renaming of interfaces that are
administratively up unless the 'IFF_LIVE_RENAME_OK' private flag was set
by the kernel.
The original solution [2] to this problem was to add a new parameter to
the netconsole configuration parameters that allows renaming of
the interface used by netconsole while it is administratively up.
However, during the discussion that followed, it became apparent that we
have no reason to keep the current restriction and instead we should
allow user space to rename interfaces regardless of their administrative
state:
1. The restriction was put in place over 20 years ago when renaming was
only possible via IOCTL and before rtnetlink started notifying user
space about such changes like it does today.
2. The 'IFF_LIVE_RENAME_OK' flag was added over 3 years ago in version
5.2 and no regressions were reported.
3. In-kernel listeners to 'NETDEV_CHANGENAME' do not seem to care about
the administrative state of interface.
Therefore, allow user space to rename running interfaces by removing the
restriction and the associated 'IFF_LIVE_RENAME_OK' flag. Help in
possible triage by emitting a message to the kernel log that an
interface was renamed while UP.
[1] https://www.kernel.org/doc/Documentation/networking/netconsole.rst
[2] https://lore.kernel.org/netdev/20221102002420.2613004-1-andy.ren@getcruise.com/
Signed-off-by: Andy Ren <andy.ren@getcruise.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rakesh Sankaranarayanan says:
====================
net: dsa: microchip: ksz_pwrite status check for lan937x and irq and error checking updates for ksz series
This patch series include following changes,
- Add KSZ9563 inside ksz_switch_chips. As per current structure,
KSZ9893 is reused inside ksz_switch_chips structure, but since
there is a mismatch in number of irq's, new member added for KSZ9563
and sku detected based on Global Chip ID 4 Register. Compatible
string from device tree mapped to KSZ9563 for spi and i2c mode
probes.
- Assign device interrupt during i2c probe operation.
- Add error checking for ksz_pwrite inside lan937x_change_mtu. After v6.0,
ksz_pwrite updated to have return type int instead of void, and
lan937x_change_mtu still uses ksz_pwrite without status verification.
- Add port_nirq as 3 for KSZ8563 switch family.
- Use dev_err_probe() instead of dev_err() to have more standardized error
formatting and logging.
v1 -> v2:
- Removed regmap validation patch from the series, planning to take
up in future after checking for any better approach and studying
the actual need for this change.
- Resolved error reported in ksz8863_smi.c file.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Probe functions uses normal dev_err() to check error conditions
and print messages. Replace dev_err() with dev_err_probe() to
have more standardized format and error logging.
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
KSZ8563 have three port interrupts: PTP, PHY and ACL. Add
port_nirq as 3 for KSZ8563 inside ksz_chip_data.
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add status validation for port register write inside
lan937x_change_mtu. ksz_pwrite and ksz_pread api's are
updated with return type int (Reference patch mentioned
below). Update lan937x_change_mtu with status validation
for ksz_pwrite16().
Link: https://patchwork.kernel.org/project/netdevbpf/patch/20220826105634.3855578-6-o.rempel@pengutronix.de/
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add device irq in i2c probe function.
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add KSZ9563 inside ksz_switch_chips structure with
port_nirq as 3. KSZ9563 use KSZ9893 switch parameters
but port_nirq count is 3 for KSZ9563 whereas 2 for
KSZ9893. Add KSZ9563 inside ksz_switch_chips as a separate
member and from device tree map compatible string into
KSZ9563 inside ksz_spi.c and ksz9477_i2c.c.
Global Chip ID 1 and 2 registers read value 9893, select
sku based on Global Chip ID 4 Register which read 0x1c
for KSZ9563.
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Coverity reported that the error path in rswitch_gwca_queue_alloc_skb()
has an issue to cause endless loop. So, fix the issue by changing
variables' types from u32 to int. After changed the types,
rswitch_tx_free() should use rswitch_get_num_cur_queues() to
calculate number of current queues.
Reported-by: coverity-bot <keescook+coverity-bot@chromium.org>
Addresses-Coverity-ID: 1527147 ("Control flow issues")
Fixes: 3590918b5d ("net: ethernet: renesas: Add support for "Ethernet Switch"")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20221107081021.2955122-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make the description of @policy to @p in nla_policy_len()
to clear the below warnings:
lib/nlattr.c:660: warning: Function parameter or member 'p' not described in 'nla_policy_len'
lib/nlattr.c:660: warning: Excess function parameter 'policy' description in 'nla_policy_len'
Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=2736
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/20221107062623.6709-1-yang.lee@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the rxkad security class, allocate the skcipher used to do packet
encryption and decription rather than allocating one up front and reusing
it for each packet. Reusing the skcipher precludes doing crypto in
parallel.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
rxrpc has a problem in its congestion management in that it saves the
congestion window size (cwnd) from one call to another, but if this is 0 at
the time is saved, then the next call may not actually manage to ever
transmit anything.
To this end:
(1) Don't save cwnd between calls, but rather reset back down to the
initial cwnd and re-enter slow-start if data transmission is idle for
more than an RTT.
(2) Preserve ssthresh instead, as that is a handy estimate of pipe
capacity. Knowing roughly when to stop slow start and enter
congestion avoidance can reduce the tendency to overshoot and drop
larger amounts of packets when probing.
In future, cwind growth also needs to be constrained when the window isn't
being filled due to being application limited.
Reported-by: Simon Wilkinson <sxw@auristor.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
The Rx/Tx ring is no longer used, so remove it.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Improve the tracking of which packets need to be transmitted by saving the
last ACK packet that we receive that has a populated soft-ACK table rather
than marking packets. Then we can step through the soft-ACK table and look
at the packets we've transmitted beyond that to determine which packets we
might want to retransmit.
We also look at the highest serial number that has been acked to try and
guess which packets we've transmitted the peer is likely to have seen. If
necessary, we send a ping to retrieve that number.
One downside that might be a problem is that we can't then compare the
previous acked/unacked state so easily in rxrpc_input_soft_acks() - which
is a potential problem for the slow-start algorithm.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
call->lock is no longer necessary, so remove it.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Change the way the Tx queueing works to make the following ends easier to
achieve:
(1) The filling of packets, the encryption of packets and the transmission
of packets can be handled in parallel by separate threads, rather than
rxrpc_sendmsg() allocating, filling, encrypting and transmitting each
packet before moving onto the next one.
(2) Get rid of the fixed-size ring which sets a hard limit on the number
of packets that can be retained in the ring. This allows the number
of packets to increase without having to allocate a very large ring or
having variable-sized rings.
[Note: the downside of this is that it's then less efficient to locate
a packet for retransmission as we then have to step through a list and
examine each buffer in the list.]
(3) Allow the filler/encrypter to run ahead of the transmission window.
(4) Make it easier to do zero copy UDP from the packet buffers.
(5) Make it easier to do zero copy from userspace to the packet buffers -
and thence to UDP (only if for unauthenticated connections).
To that end, the following changes are made:
(1) Use the new rxrpc_txbuf struct instead of sk_buff for keeping packets
to be transmitted in. This allows them to be placed on multiple
queues simultaneously. An sk_buff isn't really necessary as it's
never passed on to lower-level networking code.
(2) Keep the transmissable packets in a linked list on the call struct
rather than in a ring. As a consequence, the annotation buffer isn't
used either; rather a flag is set on the packet to indicate ackedness.
(3) Use the RXRPC_CALL_TX_LAST flag to indicate that the last packet to be
transmitted has been queued. Add RXRPC_CALL_TX_ALL_ACKED to indicate
that all packets up to and including the last got hard acked.
(4) Wire headers are now stored in the txbuf rather than being concocted
on the stack and they're stored immediately before the data, thereby
allowing zerocopy of a single span.
(5) Don't bother with instant-resend on transmission failure; rather,
leave it for a timer or an ACK packet to trigger.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Get rid of the Rx ring and replace it with a pair of queues instead. One
queue gets the packets that are in-sequence and are ready for processing by
recvmsg(); the other queue gets the out-of-sequence packets for addition to
the first queue as the holes get filled.
The annotation ring is removed and replaced with a SACK table. The SACK
table has the bits set that correspond exactly to the sequence number of
the packet being acked. The SACK ring is copied when an ACK packet is
being assembled and rotated so that the first ACK is in byte 0.
Flow control handling is altered so that packets that are moved to the
in-sequence queue are hard-ACK'd even before they're consumed - and then
the Rx window size in the ACK packet (rsize) is shrunk down to compensate
(even going to 0 if the window is full).
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Split up received jumbo packets into separate skbuffs by cloning the
original skbuff for each subpacket and setting the offset and length of the
data in that subpacket in the skbuff's private data. The subpackets are
then placed on the recvmsg queue separately. The security class then gets
to revise the offset and length to remove its metadata.
If we fail to clone a packet, we just drop it and let the peer resend it.
The original packet gets used for the final subpacket.
This should make it easier to handle parallel decryption of the subpackets.
It also simplifies the handling of lost or misordered packets in the
queuing/buffering loop as the possibility of overlapping jumbo packets no
longer needs to be considered.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Split the rxrpc_recvmsg tracepoint so that the tracepoints that are about
data packet processing (and which have extra pieces of information) are
separate from the tracepoint that shows the general flow of recvmsg().
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Clean up the rxrpc_propose_ACK() function. If deferred PING ACK proposal
is split out, it's only really needed for deferred DELAY ACKs. All other
ACKs, bar terminal IDLE ACK are sent immediately. The deferred IDLE ACK
submission can be handled by conversion of a DELAY ACK into an IDLE ACK if
there's nothing to be SACK'd.
Also, because there's a delay between an ACK being generated and being
transmitted, it's possible that other ACKs of the same type will be
generated during that interval. Apart from the ACK time and the serial
number responded to, most of the ACK body, including window and SACK
parameters, are not filled out till the point of transmission - so we can
avoid generating a new ACK if there's one pending that will cover the SACK
data we need to convey.
Therefore, don't propose a new DELAY or IDLE ACK for a call if there's one
already pending.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Allocate rxrpc_txbuf records for ACKs and put onto a queue for the
transmitter thread to dispatch.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
