The driver is designed to drop Rx packets and reclaim the buffers
when an allocation fails, and the network interface needs to safely
handle this packet loss. Therefore, an allocation failure of Rx
SKBs is relatively benign.
However, the output of the warning message occurs with a high
scheduling priority that can cause excessive jitter/latency for
other high priority processing.
This commit suppresses the warning messages to prevent scheduling
problems while retaining the failure count in the statistics of
the network interface.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a macsec interface is created, the mtu is calculated with the lower
interface's mtu value.
If the mtu of lower interface is lower than the length, which is needed
by macsec interface, macsec's mtu value will be overflowed.
So, if the lower interface's mtu is too low, macsec interface's mtu
should be set to 0.
Test commands:
ip link add dummy0 mtu 10 type dummy
ip link add macsec0 link dummy0 type macsec
ip link show macsec0
Before:
11: macsec0@dummy0: <BROADCAST,MULTICAST,M-DOWN> mtu 4294967274
After:
11: macsec0@dummy0: <BROADCAST,MULTICAST,M-DOWN> mtu 0
Fixes: c09440f7dcb3 ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* fix a wrong GFP_KERNEL in hwsim
* fix the debugfs mess after the mac80211 registration race fix
* suppress false-positive RCU list lockdep warnings
-----BEGIN PGP SIGNATURE-----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=SKNj
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-net-2020-04-24' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Just three changes:
* fix a wrong GFP_KERNEL in hwsim
* fix the debugfs mess after the mac80211 registration race fix
* suppress false-positive RCU list lockdep warnings
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Second set of fixes for v5.7. Quite a few iwlwifi fixes and some
maintainers file updates.
iwlwifi
* fix a bug with kmemdup() error handling
* fix a DMA pool warning about unfreed memory
* fix beacon statistics
* fix a theoritical bug in device initialisation
* fix queue limit handling and inactive TID removal
* disable ACK Enabled Aggregation which was enabled by accident
* fix transmit power setting reading from BIOS with certain versions
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJeon8dAAoJEG4XJFUm622b3I4H/2qSe/+choibIJj1QLsPuFzD
M4vYMulQO1GjKzn+t9cVp3D30oKPUKdE2hQyXQ/10YLoovfe1OfAsKxL/IDVlb4d
h4e3qf+lWslaz8X9gMfN0fU6M+fNsmcrbvce5K9V2cun2WReuTprgkdQv9ErQQkF
JB58pbLV1x3VZFaBttVFMtJ6fA9FEFlX/cw197tPtB7t20cI3i+km92bIcwYf6XS
ifSIRUWgH8KpPE2nhQUpR7CxaoCsqvuM+HMn2nMwJX8j80Ot6x+S8m+2pTEObonA
XDXwOp7htfAx+xA+Z6nY8UIbMOFpFoQAwFpzd5P54L3uw5PX/0b0vkpfOu2k9l0=
=bqg+
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-2020-04-24' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.7
Second set of fixes for v5.7. Quite a few iwlwifi fixes and some
maintainers file updates.
iwlwifi
* fix a bug with kmemdup() error handling
* fix a DMA pool warning about unfreed memory
* fix beacon statistics
* fix a theoritical bug in device initialisation
* fix queue limit handling and inactive TID removal
* disable ACK Enabled Aggregation which was enabled by accident
* fix transmit power setting reading from BIOS with certain versions
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The function sta_info_get_by_idx() uses RCU list primitive.
It is called with local->sta_mtx held from mac80211/cfg.c.
Add lockdep expression to avoid any false positive RCU list warnings.
Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com>
Link: https://lore.kernel.org/r/20200409082906.27427-1-madhuparnabhowmik10@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When fixing the initialization race, we neglected to account for
the fact that debugfs is initialized in wiphy_register(), and
some debugfs things went missing (or rather were rerooted to the
global debugfs root).
Fix this by adding debugfs entries only after wiphy_register().
This requires some changes in the rate control code since it
currently adds debugfs at alloc time, which can no longer be
done after the reordering.
Reported-by: Jouni Malinen <j@w1.fi>
Reported-by: kernel test robot <rong.a.chen@intel.com>
Reported-by: Hauke Mehrtens <hauke@hauke-m.de>
Reported-by: Felix Fietkau <nbd@nbd.name>
Cc: stable@vger.kernel.org
Fixes: 52e04b4ce5d0 ("mac80211: fix race in ieee80211_register_hw()")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Link: https://lore.kernel.org/r/20200423111344.0e00d3346f12.Iadc76a03a55093d94391fc672e996a458702875d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The change to track net_device_stats per ring to better support SMP
missed updating the rx_dropped member.
The ndo_get_stats method is also needed to combine the results for
ethtool statistics (-S) before filling in the ethtool structure.
Fixes: 37a30b435b92 ("net: bcmgenet: Track per TX/RX rings statistics")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Evidently, at some point in the pre-githistorious past,
drivers/net/ethernet/sgi/meth.h somehow contained some code from the
"snull" driver from the Linux Device Drivers book. A comment crediting
that source, asserting copyright ownership by the LDD authors, and imposing
the LDD2 license terms was duly added to the file.
Any code that may have been derived from snull is long gone, and the
distribution terms are not GPL-compatible. Since the copyright claim is
not based in fact (if it ever was), simply remove it and the distribution
terms as well.
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Alessandro Rubini <rubini@gnudd.com>
CC: Ralf Baechle <ralf@linux-mips.org>
CC: Kate Stewart <kstewart@linuxfoundation.org>
CC: "Fendt, Oliver" <oliver.fendt@siemens.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear the link partner advertisement, speed, duplex and pause when
the link goes down, as other phylib drivers do. This avoids the
stale link partner, speed and duplex settings being reported via
ethtool.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Soft lock should be taken in place of hard lock.
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
x25_lapb_receive_frame() invokes x25_get_neigh(), which returns a
reference of the specified x25_neigh object to "nb" with increased
refcnt.
When x25_lapb_receive_frame() returns, local variable "nb" becomes
invalid, so the refcount should be decreased to keep refcount balanced.
The reference counting issue happens in one path of
x25_lapb_receive_frame(). When pskb_may_pull() returns false, the
function forgets to decrease the refcnt increased by x25_get_neigh(),
causing a refcnt leak.
Fix this issue by calling x25_neigh_put() when pskb_may_pull() returns
false.
Fixes: cb101ed2c3c7 ("x25: Handle undersized/fragmented skbs")
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Normal there should be checked for nla_put_in6_addr like other
usage in net.
Detected by CoverityScan, CID# 1461639
Fixes: 01cacb00b35c ("mptcp: add netlink-based PM")
Signed-off-by: Bo YU <tsu.yubo@gmail.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function ixp4xx_eth_probe() does not perform sufficient error
checking after executing devm_ioremap_resource(), which can result
in crashes if a critical error path is encountered.
Fixes: f458ac479777 ("ARM/net: ixp4xx: Pass ethernet physical base as resource")
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the absence of MC1, the size calculation function
cudbg_mem_region_size() was returing wrong MC size and
resulted in adapter crash. This patch adds new argument
to cudbg_mem_region_size() which will have actual size
and returns error to caller in the absence of MC1.
Fixes: a1c69520f785 ("cxgb4: collect MC memory dump")
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>"
Signed-off-by: David S. Miller <davem@davemloft.net>
Sabrina Dubroca says:
====================
net: vxlan/geneve: use the correct nlattr array for extack
The ->validate callbacks for vxlan and geneve have a couple of typos
in extack, where the nlattr array for IFLA_* attributes is used
instead of the link-specific one.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
IFLA_GENEVE_* attributes are in the data array, which is correctly
used when fetching the value, but not when setting the extended
ack. Because IFLA_GENEVE_MAX < IFLA_MAX, we avoid out of bounds
array accesses, but we don't provide a pointer to the invalid
attribute to userspace.
Fixes: a025fb5f49ad ("geneve: Allow configuration of DF behaviour")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
IFLA_VXLAN_* attributes are in the data array, which is correctly
used when fetching the value, but not when setting the extended
ack. Because IFLA_VXLAN_MAX < IFLA_MAX, we avoid out of bounds
array accesses, but we don't provide a pointer to the invalid
attribute to userspace.
Fixes: 653ef6a3e4af ("vxlan: change vxlan_[config_]validate() to use netlink_ext_ack for error reporting")
Fixes: b4d3069783bc ("vxlan: Allow configuration of DF behaviour")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mlxsw_sp_acl_rulei_create() function is supposed to return an error
pointer from mlxsw_afa_block_create(). The problem is that these
functions both return NULL instead of error pointers. Half the callers
expect NULL and half expect error pointers so it could lead to a NULL
dereference on failure.
This patch changes both of them to return error pointers and changes all
the callers which checked for NULL to check for IS_ERR() instead.
Fixes: 4cda7d8d7098 ("mlxsw: core: Introduce flexible actions support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MV_V2_PORT_CTRL_SWRST bit in MV_V2_PORT_CTRL is reserved on 88E2110.
Setting SWRST on 88E2110 breaks packets transfer after interface down/up
cycle.
Fixes: 8f48c2ac85ed ("net: marvell10g: soft-reset the PHY when coming out of low power")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
A spin lock is taken here so we should use GFP_ATOMIC.
Fixes: 5d44fe7c9808 ("mac80211_hwsim: add frame transmission support over virtio")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20200422020154.112088-1-weiyongjun1@huawei.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The NetLabel Tools project has moved from http://netlabel.sf.net to a
GitHub project. Update to directly refer to the new home for the tools.
Signed-off-by: Salvatore Bonaccorso <carnil@debian.org>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add myself as another maintainer of dpaa2-eth.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The data fin flag is set only via a DSS option, but
mptcp_incoming_options() copies it unconditionally from the
provided RX options.
Since we do not clear all the mptcp sock RX options in a
socket free/alloc cycle, we can end-up with a stray data_fin
value while parsing e.g. MPC packets.
That would lead to mapping data corruption and will trigger
a few WARN_ON() in the RX path.
Instead of adding a costly memset(), fetch the data_fin flag
only for DSS packets - when we always explicitly initialize
such bit at option parsing time.
Fixes: 648ef4b88673 ("mptcp: Implement MPTCP receive path")
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a qdisc is attached to the VRF device, the packet goes down the ndo
xmit function which is setup to send the packet back to the VRF driver
which does a lookup to send the packet out. The lookup in the VRF driver
is not considering xfrm policies. Change it to use ip6_dst_lookup_flow
rather than ip6_route_output.
Fixes: 35402e313663 ("net: Add IPv6 support to VRF device")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for non-root users to send ICMP ECHO requests was added
back in Linux 3.0 kernel, but the documentation for the sysctl
to enable it has been missing.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jere Leppänen says:
====================
sctp: Fix problems with peer restart when in SHUTDOWN-PENDING state and socket is closed
These patches are related to the scenario described in commit
bdf6fa52f01b ("sctp: handle association restarts when the socket is
closed."). To recap, when our association is in SHUTDOWN-PENDING state
and we've closed our one-to-one socket, while the peer crashes without
being detected, restarts and reconnects using the same addresses and
ports, we start association shutdown.
In this case, Cumulative TSN Ack in the SHUTDOWN that we send has
always been incorrect. Additionally, bundling of the SHUTDOWN with the
COOKIE-ACK was broken by a later commit. This series fixes both of
these issues.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When starting shutdown in sctp_sf_do_dupcook_a(), get the value for
SHUTDOWN Cumulative TSN Ack from the new association, which is
reconstructed from the cookie, instead of the old association, which
the peer doesn't have anymore.
Otherwise the SHUTDOWN is either ignored or replied to with an ABORT
by the peer because CTSN Ack doesn't match the peer's Initial TSN.
Fixes: bdf6fa52f01b ("sctp: handle association restarts when the socket is closed.")
Signed-off-by: Jere Leppänen <jere.leppanen@nokia.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we start shutdown in sctp_sf_do_dupcook_a(), we want to bundle
the SHUTDOWN with the COOKIE-ACK to ensure that the peer receives them
at the same time and in the correct order. This bundling was broken by
commit 4ff40b86262b ("sctp: set chunk transport correctly when it's a
new asoc"), which assigns a transport for the COOKIE-ACK, but not for
the SHUTDOWN.
Fix this by passing a reference to the COOKIE-ACK chunk as an argument
to sctp_sf_do_9_2_start_shutdown() and onward to
sctp_make_shutdown(). This way the SHUTDOWN chunk is assigned the same
transport as the COOKIE-ACK chunk, which allows them to be bundled.
In sctp_sf_do_9_2_start_shutdown(), the void *arg parameter was
previously unused. Now that we're taking it into use, it must be a
valid pointer to a chunk, or NULL. There is only one call site where
it's not, in sctp_sf_autoclose_timer_expire(). Fix that too.
Fixes: 4ff40b86262b ("sctp: set chunk transport correctly when it's a new asoc")
Signed-off-by: Jere Leppänen <jere.leppanen@nokia.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no reason to fail the probing of the switch if the MTU couldn't
be configured correctly (either the switch port itself, or the host
port) for whatever reason. MTU-sized traffic probably won't work, sure,
but we can still probably limp on and support some form of communication
anyway, which the users would probably appreciate more.
Fixes: bfcb813203e6 ("net: dsa: configure the MTU for switch ports")
Reported-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fib_tests is spewing errors:
...
Cannot open network namespace "ns1": No such file or directory
Cannot open network namespace "ns1": No such file or directory
Cannot open network namespace "ns1": No such file or directory
Cannot open network namespace "ns1": No such file or directory
ping: connect: Network is unreachable
Cannot open network namespace "ns1": No such file or directory
Cannot open network namespace "ns1": No such file or directory
...
Each test entry in fib_tests is supposed to do its own setup and
cleanup. Right now the $IP commands in fib_suppress_test are
failing because there is no ns1. Add the setup/cleanup and logging
expected for each test.
Fixes: ca7a03c41753 ("ipv6: do not free rt if FIB_LOOKUP_NOREF is set on suppress rule")
Signed-off-by: David Ahern <dsahern@gmail.com>
Cc: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
net: dsa: b53: Various ARL fixes
This patch series fixes a number of short comings in the existing b53
driver ARL management logic in particular:
- we were not looking up the {MAC,VID} tuples against their VID, despite
having VLANs enabled
- the MDB entries (multicast) would lose their validity as soon as a
single port in the vector would leave the entry
- the ARL was currently under utilized because we would always place new
entries in bin index #1, instead of using all possible bins available,
thus reducing the ARL effective size by 50% or 75% depending on the
switch generation
- it was possible to overwrite the ARL entries because no proper space
verification was done
This patch series addresses all of these issues.
Changes in v2:
- added a new patch to correctly flip invidual VLAN learning vs. shared
VLAN learning depending on the global VLAN state
- added Andrew's R-b tags for patches which did not change
- corrected some verbosity and minor issues in patch #4 to match caller
expectations, also avoid a variable length DECLARE_BITMAP() call
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Flip the IVL_SVL_SELECT bit correctly based on the VLAN enable status,
the default is to perform Shared VLAN learning instead of Individual
learning.
Fixes: 1da6df85c6fb ("net: dsa: b53: Implement ARL add/del/dump operations")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When asking the ARL to read a MAC address, we will get a number of bins
returned in a single read. Out of those bins, there can essentially be 3
states:
- all bins are full, we have no space left, and we can either replace an
existing address or return that full condition
- the MAC address was found, then we need to return its bin index and
modify that one, and only that one
- the MAC address was not found and we have a least one bin free, we use
that bin index location then
The code would unfortunately fail on all counts.
Fixes: 1da6df85c6fb ("net: dsa: b53: Implement ARL add/del/dump operations")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ARL {MAC,VID} tuple and the forward entry were off by 0x10 bytes,
which means that when we read/wrote from/to ARL bin index 0, we were
actually accessing the ARLA_RWCTRL register.
Fixes: 1da6df85c6fb ("net: dsa: b53: Implement ARL add/del/dump operations")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When support for the MDB entries was added, the valid bit was correctly
changed to be assigned depending on the remaining port bitmask, that is,
if there were no more ports added to the entry's port bitmask, the entry
now becomes invalid. There was another assignment a few lines below that
would override this which would invalidate entries even when there were
still multiple ports left in the MDB entry.
Fixes: 5d65b64a3d97 ("net: dsa: b53: Add support for MDB")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When VLAN is enabled, and an ARL search is issued, we also need to
compare the full {MAC,VID} tuple before returning a successful search
result.
Fixes: 1da6df85c6fb ("net: dsa: b53: Implement ARL add/del/dump operations")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern says:
====================
net: Fix looping with vrf, xfrms and qdisc on VRF
Trev reported that use of VRFs with xfrms is looping when a qdisc
is added to the VRF device. The combination of xfrm + qdisc is not
handled by the VRF driver which lost track that it has already
seen the packet.
The XFRM_TRANSFORMED flag is used by the netfilter code for a similar
purpose, so re-use for VRF. Patch 1 drops the #ifdef around setting
the flag in the xfrm output functions. Patch 2 adds a check to
the VRF driver for flag; if set the packet has already passed through
the VRF driver once and does not need to recirculated a second time.
This is a day 1 bug with VRFs; stable wise, I would only take this
back to 4.14. I have a set of test cases which I will submit to
net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid a loop with qdiscs and xfrms, check if the skb has already gone
through the qdisc attached to the VRF device and then to the xfrm layer.
If so, no need for a second redirect.
Fixes: 193125dbd8eb ("net: Introduce VRF device driver")
Reported-by: Trev Larock <trev@larock.ca>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPSKB_XFRM_TRANSFORMED and IP6SKB_XFRM_TRANSFORMED are skb flags set by
xfrm code to tell other skb handlers that the packet has been passed
through the xfrm output functions. Simplify the code and just always
set them rather than conditionally based on netfilter enabled thus
making the flag available for other users.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
See:
https://www.rfc-editor.org/authors/rfc8781.txt
Cc: Erik Kline <ek@google.com>
Cc: Jen Linkova <furry@google.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: Michael Haro <mharo@google.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Fixes: c24a77edc9a7 ("ipv6: ndisc: add support for 'PREF64' dns64 prefix identifier")
Signed-off-by: David S. Miller <davem@davemloft.net>
lan87xx_phy_init() initializes the lan87xx phy hardware
including its TC10 Wake-up and Sleep features.
Fixes: 3e50d2da5850 ("Add driver for Microchip LAN87XX T1 PHYs")
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
v0->v1:
- Add more details in the commit message and source comments.
- Update to the latest initialization sequences.
- Add access_ereg_modify_changed().
- Fix access_ereg() to access SMI bank correctly.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to enable Intel SERDES power up/down sequence. The SERDES
converts 8/10 bits data to SGMII signal. Below is an example of
HW configuration for SGMII mode. The SERDES is located in the PHY IF
in the diagram below.
<-----------------GBE Controller---------->|<--External PHY chip-->
+----------+ +----+ +---+ +----------+
| EQoS | <-GMII->| DW | < ------ > |PHY| <-SGMII-> | External |
| MAC | |xPCS| |IF | | PHY |
+----------+ +----+ +---+ +----------+
^ ^ ^ ^
| | | |
+---------------------MDIO-------------------------+
PHY IF configuration and status registers are accessible through
mdio address 0x15 which is defined as mdio_adhoc_addr. During D0,
The driver will need to power up PHY IF by changing the power state
to P0. Likewise, for D3, the driver sets PHY IF power state to P3.
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the function devm_platform_ioremap_resource_byname() to simplify
source code which calls the functions platform_get_resource_byname()
and devm_ioremap_resource(). Remove also a few error messages which
became unnecessary with this software refactoring.
Suggested-by: Markus Elfring <Markus.Elfring@web.de>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The '==' expression itself is bool, no need to convert it to bool again.
This fixes the following coccicheck warning:
drivers/net/ethernet/intel/e1000/e1000_main.c:1479:44-49: WARNING:
conversion to bool not needed here
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The '==' expression itself is bool, no need to convert it to bool again.
This fixes the following coccicheck warning:
drivers/net/ethernet/intel/i40e/i40e_main.c:1614:52-57: WARNING:
conversion to bool not needed here
drivers/net/ethernet/intel/i40e/i40e_main.c:11439:52-57: WARNING:
conversion to bool not needed here
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The '==' expression itself is bool, no need to convert it to bool again.
This fixes the following coccicheck warning:
drivers/ptp/ptp_ines.c:403:55-60: WARNING: conversion to bool not
needed here
drivers/ptp/ptp_ines.c:404:55-60: WARNING: conversion to bool not
needed here
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 018d26fcd12a ("cgroup, netclassid: periodically release file_lock
on classid") added a second cond_resched to write_classid indirectly by
update_classid_task. Remove the one in write_classid.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Dmitry Yakunin <zeil@yandex-team.ru>
Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
