In __spi_pump_transfer_message(), the message was not finalized in the
first error return as it is in the other error return paths. Not
finalizing the message could cause anything waiting on the message to
complete to hang forever.
This adds the missing call to spi_finalize_current_message().
Fixes: ae7d2346dc89 ("spi: Don't use the message queue if possible in spi_sync")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://msgid.link/r/20240125205312.3458541-2-dlechner@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>:
This patch series adds support to the SPI framework for using multiple
chip selects.
AMD-Xilinx GQSPI controller has two advanced mode that allows the
controller to consider two flashes as one single device.
One of these two mode is the parallel mode in which each byte of data is
stored in both devices, the even bits in the lower flash & the odd bits in
the upper flash. The byte split is automatically handled by the QSPI
controller.
The other mode is the stacked mode in which both the flashes share the
same SPI bus but each of the device contain half of the data. In this mode,
the controller does not follow CS requests but instead internally wires the
two CS levels with the value of the most significant address bit.
For supporting both these modes SPI core need to be updated for providing
multiple CS for a single SPI device.
For adding multi CS support the SPI device need to be aware of all the CS
values. So, the "chip_select" member in the spi_device structure is now an
array that holds all the CS values.
spi_device structure now has a "cs_index_mask" member. This acts as an
index to the chip_select array. If nth bit of spi->cs_index_mask is set
then the driver would assert spi->chip_select[n].
In parallel mode all the chip selects are asserted/de-asserted
simultaneously and each byte of data is stored in both devices, the even
bits in one, the odd bits in the other. The split is automatically handled
by the GQSPI controller. The GQSPI controller supports a maximum of two
flashes connected in parallel mode. A SPI_CONTROLLER_MULTI_CS flag bit is
added in the spi controller flags, through ctlr->flags the spi core
will make sure that the controller is capable of handling multiple chip
selects at once.
For supporting multiple CS via GPIO the cs_gpiod member of the spi_device
structure is now an array that holds the gpio descriptor for each
chipselect.
CS GPIO is not tested on our hardware, but it has been tested by @Stefan
https://lore.kernel.org/all/005001da1efc$619ad5a0$24d080e0$@opensource.cirrus.com/
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Tested-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231125092137.2948-4-amit.kumar-mahapatra@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The default message transfer implementation - spi_transfer_one_message -
invokes the specific device driver's transfer_one(), then waits for
completion. However, there is no mechanism for the device driver to
report failure in the middle of the transfer.
Introduce SPI_TRANS_FAIL_IO for drivers to report transfer failure.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/4b420dac528e60f122adde16851da88e4798c1ea.1701274975.git.namcao@linutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
A race condition exists where a synchronous (noqueue) transfer can be
active during a system suspend. This can cause a null pointer
dereference exception to occur when the system resumes.
Example order of events leading to the exception:
1. spi_sync() calls __spi_transfer_message_noqueue() which sets
ctlr->cur_msg
2. Spi transfer begins via spi_transfer_one_message()
3. System is suspended interrupting the transfer context
4. System is resumed
6. spi_controller_resume() calls spi_start_queue() which resets cur_msg
to NULL
7. Spi transfer context resumes and spi_finalize_current_message() is
called which dereferences cur_msg (which is now NULL)
Wait for synchronous transfers to complete before suspending by
acquiring the bus mutex and setting/checking a suspend flag.
Signed-off-by: Mark Hasemeyer <markhas@chromium.org>
Link: https://lore.kernel.org/r/20231107144743.v1.1.I7987f05f61901f567f7661763646cb7d7919b528@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@kernel.org
Export acpi_spi_find_controller_by_adev() so that ACPI glue code which
wants to dynamically create a spi_device using acpi_spi_device_alloc() or
spi_new_device() on a controller, to which the code does not already have
a reference, can find the controller.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231014205314.59333-2-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Both callers of spi_stop_queue() (i.e. spi_destroy_queue() and
spi_controller_suspend()) already emit an error message if
spi_stop_queue() fails. Another warning in this case isn't helpful, so
drop it.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230916161235.1050176-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
BITS_TO_BYTES() is the existing macro which takes care about full
bytes that may fully hold the given amount of bits. Use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230714091748.89681-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Now, spi_add_device_locked() has just a line on top of __spi_add_device().
Besides that, it has a single caller. So, just kill it and embed its parts
into the caller.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230714091748.89681-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The commit 0c79378c0199 ("spi: add ancillary device support")
added a dozen of duplicating lines of code. We may move them
to the __spi_add_device(). Note, that the code may be called
under the mutex.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230714091748.89681-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Rename SPI_MASTER_GPIO_SS to SPI_CONTROLLER_GPIO_SS and
convert the users to SPI_CONTROLLER_GPIO_SS to follow
the new naming shema.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230710154932.68377-14-andriy.shevchenko@linux.intel.com
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Follow the advice of the Documentation/filesystems/sysfs.rst and show()
should only use sysfs_emit() or sysfs_emit_at() when formatting the
value to be returned to user space.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230710154932.68377-7-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of if-else-if, simply call roundup_pow_of_two(BITS_PER_BYTES()).
Note, there is no division assumed as compiler may optimize it away.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230710154932.68377-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Refactor spi_register_controller() to drop duplicate IDR allocation.
Instead of if-else-if branching use two sequential if:s, which allows
to re-use the logic of IDR allocation in all cases.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230710154932.68377-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In the couple of places the NULL check of OF node is implied by the call
that takes it as a parameter. Drop the respective duplicate checks.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230710154932.68377-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Here is the "big" set of char/misc and other driver subsystems for
6.4-rc1.
It's pretty big, but due to the removal of pcmcia drivers, almost breaks
even for number of lines added vs. removed, a nice change.
Included in here are:
- removal of unused PCMCIA drivers (finally!)
- Interconnect driver updates and additions
- Lots of IIO driver updates and additions
- MHI driver updates
- Coresight driver updates
- NVMEM driver updates, which required some OF updates
- W1 driver updates and a new maintainer to manage the subsystem
- FPGA driver updates
- New driver subsystem, CDX, for AMD systems
- lots of other small driver updates and additions
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZEp5Eg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynSXgCg0kSw3vUYwpsnhAsQkoPw1QVA23sAn2edRCMa
GEkPWjrROueCom7xbLMu
=eR+P
-----END PGP SIGNATURE-----
Merge tag 'char-misc-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc drivers updates from Greg KH:
"Here is the "big" set of char/misc and other driver subsystems for
6.4-rc1.
It's pretty big, but due to the removal of pcmcia drivers, almost
breaks even for number of lines added vs. removed, a nice change.
Included in here are:
- removal of unused PCMCIA drivers (finally!)
- Interconnect driver updates and additions
- Lots of IIO driver updates and additions
- MHI driver updates
- Coresight driver updates
- NVMEM driver updates, which required some OF updates
- W1 driver updates and a new maintainer to manage the subsystem
- FPGA driver updates
- New driver subsystem, CDX, for AMD systems
- lots of other small driver updates and additions
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (196 commits)
mcb-lpc: Reallocate memory region to avoid memory overlapping
mcb-pci: Reallocate memory region to avoid memory overlapping
mcb: Return actual parsed size when reading chameleon table
kernel/configs: Drop Android config fragments
virt: acrn: Replace obsolete memalign() with posix_memalign()
spmi: Add a check for remove callback when removing a SPMI driver
spmi: fix W=1 kernel-doc warnings
spmi: mtk-pmif: Drop of_match_ptr for ID table
spmi: pmic-arb: Convert to platform remove callback returning void
spmi: mtk-pmif: Convert to platform remove callback returning void
spmi: hisi-spmi-controller: Convert to platform remove callback returning void
w1: gpio: remove unnecessary ENOMEM messages
w1: omap-hdq: remove unnecessary ENOMEM messages
w1: omap-hdq: add SPDX tag
w1: omap-hdq: allow compile testing
w1: matrox: remove unnecessary ENOMEM messages
w1: matrox: use inline over __inline__
w1: matrox: switch from asm to linux header
w1: ds2482: do not use assignment in if condition
w1: ds2482: drop unnecessary header
...
Here is the large set of driver core changes for 6.4-rc1.
Once again, a busy development cycle, with lots of changes happening in
the driver core in the quest to be able to move "struct bus" and "struct
class" into read-only memory, a task now complete with these changes.
This will make the future rust interactions with the driver core more
"provably correct" as well as providing more obvious lifetime rules for
all busses and classes in the kernel.
The changes required for this did touch many individual classes and
busses as many callbacks were changed to take const * parameters
instead. All of these changes have been submitted to the various
subsystem maintainers, giving them plenty of time to review, and most of
them actually did so.
Other than those changes, included in here are a small set of other
things:
- kobject logging improvements
- cacheinfo improvements and updates
- obligatory fw_devlink updates and fixes
- documentation updates
- device property cleanups and const * changes
- firwmare loader dependency fixes.
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZEp7Sw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykitQCfamUHpxGcKOAGuLXMotXNakTEsxgAoIquENm5
LEGadNS38k5fs+73UaxV
=7K4B
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the large set of driver core changes for 6.4-rc1.
Once again, a busy development cycle, with lots of changes happening
in the driver core in the quest to be able to move "struct bus" and
"struct class" into read-only memory, a task now complete with these
changes.
This will make the future rust interactions with the driver core more
"provably correct" as well as providing more obvious lifetime rules
for all busses and classes in the kernel.
The changes required for this did touch many individual classes and
busses as many callbacks were changed to take const * parameters
instead. All of these changes have been submitted to the various
subsystem maintainers, giving them plenty of time to review, and most
of them actually did so.
Other than those changes, included in here are a small set of other
things:
- kobject logging improvements
- cacheinfo improvements and updates
- obligatory fw_devlink updates and fixes
- documentation updates
- device property cleanups and const * changes
- firwmare loader dependency fixes.
All of these have been in linux-next for a while with no reported
problems"
* tag 'driver-core-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (120 commits)
device property: make device_property functions take const device *
driver core: update comments in device_rename()
driver core: Don't require dynamic_debug for initcall_debug probe timing
firmware_loader: rework crypto dependencies
firmware_loader: Strip off \n from customized path
zram: fix up permission for the hot_add sysfs file
cacheinfo: Add use_arch[|_cache]_info field/function
arch_topology: Remove early cacheinfo error message if -ENOENT
cacheinfo: Check cache properties are present in DT
cacheinfo: Check sib_leaf in cache_leaves_are_shared()
cacheinfo: Allow early level detection when DT/ACPI info is missing/broken
cacheinfo: Add arm64 early level initializer implementation
cacheinfo: Add arch specific early level initializer
tty: make tty_class a static const structure
driver core: class: remove struct class_interface * from callbacks
driver core: class: mark the struct class in struct class_interface constant
driver core: class: make class_register() take a const *
driver core: class: mark class_release() as taking a const *
driver core: remove incorrect comment for device_create*
MIPS: vpe-cmp: remove module owner pointer from struct class usage.
...
A fairly standard release for SPI with the exception of a change to the
API for specifying chip selects done in preparation for supporting
devices with more than one chip select, this required some mechanical
changes throughout the tree which have been cooking in -next happily for
a while. There's also a new API to allow us to TPM chips on half duplex
controllers.
There's three commits in here that were mangled by a bad interaction
between the alsa-devel mailing list software and b4, I didn't notice
until there were merges on top with it being SPI not ALSA. It seemed
clear enough to not be worth going back and fixing.
- Refactoring in preparation for supporting multiple chip selects for a
single device, needed by some flash devices, which required a change
in the SPI device API visible throughout the tree.
- Support for hardware assisted interaction with SPI TPMs on half
duplex controllers, implemented on nVidia Tedra210 QuadSPI.
- Optimisation for large transfers on fsl-cpm devices.
- Cleanups around device property use which fix some sisues with
fwnode.
- Use of both void remove() and devm_platform_.*ioremap_resource().
- Support for AMD Pensando Elba, Amlogic A1, Cadence device mode,
Intel MetorLake-S and StarFive J7110 QuadSPI.
The final commit converting to DEV_PM_OPS() was applied late to fix a
warning that was introduced by some of the earlier work.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmRIFQgACgkQJNaLcl1U
h9BJOwf+JF2RySdn5g1LsyTndPZhLfw4iJgTHaMlnv5tiPHvYVYMM/mNMbMr5Znh
Y2T0OUkzuRfOK273C+hItC1bTYFTa2cEbDb5dpmKBOZdQ3hjGsZQBvuH2bScUQ+a
H7UgD3FYOJST6k6rRgZQxVMPePFrXAOaO1gmFWTR3v1EcEr2JeQnjZsmymFXcTnc
CtPg9N3RvhVnq5aXuxSgQeyyKIjo4LJh/eZ2mexPIu0DeUq3MftaWwSwCXFIoeNC
DMLA4mZWTgf/yt6JUALwLr+bIiJjb4qGjp3xGZ2wmX7zn73f9QQvuunKb1V4zbNF
EdXLo2VjA9cZjsihenBaKeHnkfgNfA==
=IRqY
-----END PGP SIGNATURE-----
Merge tag 'spi-v6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"A fairly standard release for SPI with the exception of a change to
the API for specifying chip selects done in preparation for supporting
devices with more than one chip select, this required some mechanical
changes throughout the tree which have been cooking in -next happily
for a while.
There's also a new API to allow us to support TPM chips on half duplex
controllers.
Summary:
- Refactoring in preparation for supporting multiple chip selects for
a single device, needed by some flash devices, which required a
change in the SPI device API visible throughout the tree
- Support for hardware assisted interaction with SPI TPMs on half
duplex controllers, implemented on nVidia Tedra210 QuadSPI
- Optimisation for large transfers on fsl-cpm devices
- Cleanups around device property use which fix some sisues with
fwnode
- Use of both void remove() and devm_platform_.*ioremap_resource()
- Support for AMD Pensando Elba, Amlogic A1, Cadence device mode,
Intel MetorLake-S and StarFive J7110 QuadSPI"
* tag 'spi-v6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (185 commits)
spi: bcm63xx: use macro DEFINE_SIMPLE_DEV_PM_OPS
spi: tegra210-quad: Enable TPM wait polling
spi: Add TPM HW flow flag
spi: bcm63xx: remove PM_SLEEP based conditional compilation
spi: cadence-quadspi: use macro DEFINE_SIMPLE_DEV_PM_OPS
spi: spi-cadence: Add support for Slave mode
spi: spi-cadence: Switch to spi_controller structure
spi: cadence-quadspi: fix suspend-resume implementations
spi: dw: Add support for AMD Pensando Elba SoC
spi: dw: Add AMD Pensando Elba SoC SPI Controller
spi: cadence-quadspi: Disable the SPI before reconfiguring
spi: cadence-quadspi: Update the read timeout based on the length
spi: spi-loopback-test: Add module param for iteration length
spi: add support for Amlogic A1 SPI Flash Controller
dt-bindings: spi: add Amlogic A1 SPI controller
spi: fsl-spi: No need to check transfer length versus word size
spi: fsl-spi: Change mspi_apply_cpu_mode_quirks() to void
spi: fsl-cpm: Use 16 bit mode for large transfers with even size
spi: fsl-spi: Re-organise transfer bits_per_word adaptation
spi: fsl-spi: Fix CPM/QE mode Litte Endian
...
- Fix interaction between fw_devlink and DT overlays causing
devices to not be probed
- Fix the compatible string for loongson,cpu-interrupt-controller
-----BEGIN PGP SIGNATURE-----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=x2A8
-----END PGP SIGNATURE-----
Merge tag 'devicetree-fixes-for-6.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
- Fix interaction between fw_devlink and DT overlays causing devices to
not be probed
- Fix the compatible string for loongson,cpu-interrupt-controller
* tag 'devicetree-fixes-for-6.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
treewide: Fix probing of devices in DT overlays
dt-bindings: interrupt-controller: loongarch: Fix mismatched compatible
When loading a DT overlay that creates a device, the device is not
probed, unless the DT overlay is unloaded and reloaded again.
After the recent refactoring to improve fw_devlink, it no longer depends
on the "compatible" property to identify which device tree nodes will
become struct devices. fw_devlink now picks up dangling consumers
(consumers pointing to descendent device tree nodes of a device that
aren't converted to child devices) when a device is successfully bound
to a driver. See __fw_devlink_pickup_dangling_consumers().
However, during DT overlay, a device's device tree node can have
sub-nodes added/removed without unbinding/rebinding the driver. This
difference in behavior between the normal device instantiation and
probing flow vs. the DT overlay flow has a bunch of implications that
are pointed out elsewhere[1]. One of them is that the fw_devlink logic
to pick up dangling consumers is never exercised.
This patch solves the fw_devlink issue by marking all DT nodes added by
DT overlays with FWNODE_FLAG_NOT_DEVICE (fwnode that won't become
device), and by clearing the flag when a struct device is actually
created for the DT node. This way, fw_devlink knows not to have
consumers waiting on these newly added DT nodes, and to propagate the
dependency to an ancestor DT node that has the corresponding struct
device.
Based on a patch by Saravana Kannan, which covered only platform and spi
devices.
[1] https://lore.kernel.org/r/CAGETcx_bkuFaLCiPrAWCPQz+w79ccDp6=9e881qmK=vx3hBMyg@mail.gmail.com
Fixes: 4a032827daa89350 ("of: property: Simplify of_link_to_phandle()")
Link: https://lore.kernel.org/r/CAGETcx_+rhHvaC_HJXGrr5_WAd2+k5f=rWYnkCZ6z5bGX-wj4w@mail.gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Saravana Kannan <saravanak@google.com>
Tested-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
Link: https://lore.kernel.org/r/e1fa546682ea4c8474ff997ab6244c5e11b6f8bc.1680182615.git.geert+renesas@glider.be
Signed-off-by: Rob Herring <robh@kernel.org>
This helper does not produce a real modalias, but tries to get the
"product" compatible part of the "vendor,product" compatibles only. It
is far from creating a purely useful modalias string and does not seem
to be used like that directly anyway, so let's try to give this helper a
more meaningful name before moving there a real modalias helper (already
existing under of/device.c).
Also update the various documentations to refer to the strings as
"aliases" rather than "modaliases" which has a real meaning in the Linux
kernel.
There is no functional change.
Cc: Rafael J. Wysocki <rafael@kernel.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Wolfram Sang <wsa@kernel.org>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Sebastian Reichel <sre@kernel.org>
Link: https://lore.kernel.org/r/20230404172148.82422-9-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to manually set the owner of a struct class, as the
registering function does it automatically, so remove all of the
explicit settings from various drivers that did so as it is unneeded.
This allows us to remove this pointer entirely from this structure going
forward.
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Link: https://lore.kernel.org/r/20230313181843.1207845-2-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add spi_split_transfers_maxwords() function that splits
spi_transfers transparently into multiple transfers
that are below a given number of SPI words.
This function reuses most of its code from
spi_split_transfers_maxsize() and for transfers with
eight or less bits per word actually behaves the same.
Signed-off-by: Leonard Göhrs <l.goehrs@pengutronix.de>
Link: https://lore.kernel.org/r/20230310092053.1006459-1-l.goehrs@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
spi_pcpu_stats_totalize() is a rather large macro, and is instantiated
28 times, causing a large amount of duplication in the amount of
generated code.
Reduce the duplication by replacing spi_pcpu_stats_totalize() by a real
C function, and absorb all other common code from
spi_statistics_##name##_show(). As (a) the old "field" parameter was
the name of a structure member, which cannot be passed to a function,
and (b) passing a pointer to the member is also not an option, due to
the loop over all possible CPUs, the "field" parameter is replaced by an
"offset" parameter, pointing to a location within the structure.
This reduces kernel size by ca. 4 KiB (on arm32 and arm64).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/cb7690d9d04c06eec23dbb98fbb5444082125cff.1677594432.git.geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Here is the large set of driver core changes for 6.3-rc1.
There's a lot of changes this development cycle, most of the work falls
into two different categories:
- fw_devlink fixes and updates. This has gone through numerous review
cycles and lots of review and testing by lots of different devices.
Hopefully all should be good now, and Saravana will be keeping a
watch for any potential regression on odd embedded systems.
- driver core changes to work to make struct bus_type able to be moved
into read-only memory (i.e. const) The recent work with Rust has
pointed out a number of areas in the driver core where we are
passing around and working with structures that really do not have
to be dynamic at all, and they should be able to be read-only making
things safer overall. This is the contuation of that work (started
last release with kobject changes) in moving struct bus_type to be
constant. We didn't quite make it for this release, but the
remaining patches will be finished up for the release after this
one, but the groundwork has been laid for this effort.
Other than that we have in here:
- debugfs memory leak fixes in some subsystems
- error path cleanups and fixes for some never-able-to-be-hit
codepaths.
- cacheinfo rework and fixes
- Other tiny fixes, full details are in the shortlog
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY/ipdg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynL3gCgwzbcWu0So3piZyLiJKxsVo9C2EsAn3sZ9gN6
6oeFOjD3JDju3cQsfGgd
=Su6W
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the large set of driver core changes for 6.3-rc1.
There's a lot of changes this development cycle, most of the work
falls into two different categories:
- fw_devlink fixes and updates. This has gone through numerous review
cycles and lots of review and testing by lots of different devices.
Hopefully all should be good now, and Saravana will be keeping a
watch for any potential regression on odd embedded systems.
- driver core changes to work to make struct bus_type able to be
moved into read-only memory (i.e. const) The recent work with Rust
has pointed out a number of areas in the driver core where we are
passing around and working with structures that really do not have
to be dynamic at all, and they should be able to be read-only
making things safer overall. This is the contuation of that work
(started last release with kobject changes) in moving struct
bus_type to be constant. We didn't quite make it for this release,
but the remaining patches will be finished up for the release after
this one, but the groundwork has been laid for this effort.
Other than that we have in here:
- debugfs memory leak fixes in some subsystems
- error path cleanups and fixes for some never-able-to-be-hit
codepaths.
- cacheinfo rework and fixes
- Other tiny fixes, full details are in the shortlog
All of these have been in linux-next for a while with no reported
problems"
[ Geert Uytterhoeven points out that that last sentence isn't true, and
that there's a pending report that has a fix that is queued up - Linus ]
* tag 'driver-core-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (124 commits)
debugfs: drop inline constant formatting for ERR_PTR(-ERROR)
OPP: fix error checking in opp_migrate_dentry()
debugfs: update comment of debugfs_rename()
i3c: fix device.h kernel-doc warnings
dma-mapping: no need to pass a bus_type into get_arch_dma_ops()
driver core: class: move EXPORT_SYMBOL_GPL() lines to the correct place
Revert "driver core: add error handling for devtmpfs_create_node()"
Revert "devtmpfs: add debug info to handle()"
Revert "devtmpfs: remove return value of devtmpfs_delete_node()"
driver core: cpu: don't hand-override the uevent bus_type callback.
devtmpfs: remove return value of devtmpfs_delete_node()
devtmpfs: add debug info to handle()
driver core: add error handling for devtmpfs_create_node()
driver core: bus: update my copyright notice
driver core: bus: add bus_get_dev_root() function
driver core: bus: constify bus_unregister()
driver core: bus: constify some internal functions
driver core: bus: constify bus_get_kset()
driver core: bus: constify bus_register/unregister_notifier()
driver core: remove private pointer from struct bus_type
...
Group some variables based on their sizes to reduce hole and avoid padding.
On x86_64, this shrinks the size from 144 to 128 bytes.
Turn 'timestamped' into a bitfield so that it can be easily merged with
some other bifields and move 'error'.
This should have no real impact on memory allocation because 'struct
spi_transfer' is mostly used on stack, but it can save a few cycles
when the structure is initialized or copied.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/93a051da85a895bc6003aedfb00a13e1c2fc6338.1676370870.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently exec_op is always required if controller driver provides
mem_ops. But some controller such as bcm63xx-hsspi may only need to
implement other operation like supports_op and use the default
execution operation. This patch removes this restriction.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Link: https://lore.kernel.org/r/20230209200246.141520-13-william.zhang@broadcom.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For SPI controller that implements transfer_one_message, it needs to
insert the delay that required by cs change event between the transfers.
Add a wrapper for the local function _spi_transfer_cs_change_delay_exec
and export it for SPI controller driver to use.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Link: https://lore.kernel.org/r/20230209200246.141520-9-william.zhang@broadcom.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>:
In preparation for supporting devices with multiple chip selects add an
interface for accessing the chip selects via a function.
Supporting multi-cs in spi core and spi controller drivers would require
the chip_select & cs_gpiod members of struct spi_device to be an array.
But changing the type of these members to array would break the spi driver
functionality. To make the transition smoother introduced four new APIs to
get/set the spi->chip_select & spi->cs_gpiod and replaced all
spi->chip_select and spi->cs_gpiod references in spi core with the API
calls.
While adding multi-cs support in further patches the chip_select & cs_gpiod
members of the spi_device structure would be converted to arrays & the
"idx" parameter of the APIs would be used as array index i.e.,
spi->chip_select[idx] & spi->cs_gpiod[idx] respectively.
Suggested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20230119185342.2093323-2-amit.kumar-mahapatra@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The uevent() callback in struct bus_type should not be modifying the
device that is passed into it, so mark it as a const * and propagate the
function signature changes out into all relevant subsystems that use
this callback.
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230111113018.459199-16-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we support parsing the setup time from the Device Tree, we can
also easily support the remaining hold and inactive time delay values.
Signed-off-by: Janne Grunau <j@jannau.net>
Signed-off-by: Hector Martin <marcan@marcan.st>
Link: https://lore.kernel.org/r/20230113102309.18308-4-marcan@marcan.st
Signed-off-by: Mark Brown <broonie@kernel.org>
65us is not a reasonable maximum for this property, as some devices
might need a much longer setup time (e.g. those driven by firmware on
the other end). Plus, device tree property values are in 32-bit cells
and smaller widths should not be used without good reason.
Also move the logic to a helper function, since this will later be used
to parse other CS delay properties too.
Fixes: 33a2fde5f77b ("spi: Introduce spi-cs-setup-ns property")
Signed-off-by: Janne Grunau <j@jannau.net>
Signed-off-by: Hector Martin <marcan@marcan.st>
Link: https://lore.kernel.org/r/20230113102309.18308-2-marcan@marcan.st
Signed-off-by: Mark Brown <broonie@kernel.org>
As mentioned in the corresponding DT binding commit, the naming scheme
for delay properties includes "delay" in the name, so let's keep that
consistent.
Fixes: 33a2fde5f77b ("spi: Introduce spi-cs-setup-ns property")
Signed-off-by: Hector Martin <marcan@marcan.st>
Link: https://lore.kernel.org/r/20230104093631.15611-3-marcan@marcan.st
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 4ccf359849ce ("spi: remove spi_set_cs_timing()"), removed the
method as noboby used it. Nobody used it probably because some SPI
controllers use some default large cs-setup time that covers the usual
cs-setup time required by the spi devices. There are though SPI controllers
that have a smaller granularity for the cs-setup time and their default
value can't fulfill the spi device requirements. That's the case for the
at91 QSPI IPs where the default cs-setup time is half of the QSPI clock
period. This was observed when using an sst26vf064b SPI NOR flash which
needs a spi-cs-setup-ns = <7>; in order to be operated close to its maximum
104 MHz frequency.
Call spi_set_cs_timing() in spi_setup() just before calling spi_set_cs(),
as the latter needs the CS timings already set.
If spi->controller->set_cs_timing is not set, the method will return 0.
There's no functional impact expected for the existing drivers. Even if the
spi-mt65xx.c and spi-tegra114.c drivers set the set_cs_timing method,
there's no user for them as of now. The only tested user of this support
will be a SPI NOR flash that comunicates with the Atmel QSPI controller for
which the support follows in the next patches.
One will notice that this support is a bit different from the one that was
removed in commit 4ccf359849ce ("spi: remove spi_set_cs_timing()"),
because this patch adapts to the changes done after the removal: the move
of the cs delays to the spi device, the retirement of the lelgacy GPIO
handling. The mutex handling was removed from spi_set_cs_timing() because
we now always call spi_set_cs_timing() in spi_setup(), which already
handles the spi->controller->io_mutex, so use the mutex handling from
spi_setup().
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20221117105249.115649-4-tudor.ambarus@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI NOR flashes have specific cs-setup time requirements without which
they can't work at frequencies close to their maximum supported frequency,
as they miss the first bits of the instruction command. Unrecognized
commands are ignored, thus the flash will be unresponsive. Introduce the
spi-cs-setup-ns property to allow spi devices to specify their cs setup
time.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20221117105249.115649-3-tudor.ambarus@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For using modern names host/target to instead of all the legacy names,
I think it takes 3 steps:
- step1: introduce new helpers with modern naming.
- step2: switch to use these new helpers in all drivers.
- step3: remove all legacy helpers and update all legacy names.
This patch is for step1, it introduces new helpers with host/target
naming for drivers using.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221011092204.950288-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that the 32bit UP oddity is gone and 32bit uses always a sequence
count, there is no need for the fetch_irq() variants anymore.
Convert to the regular interface.
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-spi@vger.kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20221026122951.331638-1-bigeasy@linutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The proposed spi_get_device_match_data() helper is for retrieving
a driver data associated with the ID in an ID table. First, it tries
to get driver data of the device enumerated by firmware interface
(usually Device Tree or ACPI). If none is found it falls back to
the SPI ID table matching.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221020195421.10482-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
With the exception of some refactoring to fix long standing issues
where we weren't handling cache syncs properly for messages which had
PIO and DMA transfers going to the same page correctly there has been o
work on the core this time around, and it's also been quite a quiet
release for the drivers too:
- Fix cache syncs for cases where we have DMA and PIO transfers in the
same message going to the same page.
- Update the fsl_spi driver to use transfer_one() rather than a custom
transfer function.
- Support for configuring transfer speeds with the AMD SPI controller.
- Support for a second chip select and 64K erase on Intel SPI.
- Support for Microchip coreQSPI, Nuvoton NPCM845, NXP i.MX93, and
Rockchip RK3128 and RK3588.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmM62YIACgkQJNaLcl1U
h9CvPAf+MF1AzJJWH9DkR846KQh7Zt1rrujRuj5SGwvHewqjJcDtDmipAbM7mRFa
VPk6fCzfRE4btVywCDMEQX2ToB9VKBNUeP8ihVLddWrTddbkQ7hOKlTrz31dJ+6W
F9kwXkWcqWEpMYD/wr/25eT/kkNfv27oCyPU4dRQKoGGeF+zb9jYoj0+gPDl9Om8
ok7D1XAwY1wOqYqdPfl2thcUrBfoKtFvkTj+NNhqwuzWwIqfQHM2skwAjmD3fliQ
lLdRc54erCOqukDddIoWr348TyJIT4v1IXnkqY3cd7da6+kpixWae73o/7WIcQUR
4MrtPply0WWcapgU/46sCbHpjJNjjg==
=PDCv
-----END PGP SIGNATURE-----
Merge tag 'spi-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"With the exception of some refactoring to fix long standing issues
where we weren't handling cache syncs properly for messages which had
PIO and DMA transfers going to the same page correctly there has been
no work on the core this time around, and it's also been quite a quiet
release for the drivers too:
- Fix cache syncs for cases where we have DMA and PIO transfers in
the same message going to the same page
- Update the fsl_spi driver to use transfer_one() rather than a
custom transfer function
- Support for configuring transfer speeds with the AMD SPI controller
- Support for a second chip select and 64K erase on Intel SPI
- Support for Microchip coreQSPI, Nuvoton NPCM845, NXP i.MX93, and
Rockchip RK3128 and RK3588"
* tag 'spi-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (73 commits)
spi: Ensure that sg_table won't be used after being freed
spi: spi-gxp: Use devm_platform_ioremap_resource()
spi: s3c64xx: Fix large transfers with DMA
spi: Split transfers larger than max size
spi: Fix cache corruption due to DMA/PIO overlap
spi: Save current RX and TX DMA devices
spi: mt65xx: Add dma max segment size declaration
spi: migrate mt7621 text bindings to YAML
spi: renesas,sh-msiof: Add r8a779g0 support
spi: spi-fsl-qspi: Use devm_platform_ioremap_resource_byname()
spi: spi-fsl-lpspi: Use devm_platform_get_and_ioremap_resource()
spi: spi-fsl-dspi: Use devm_platform_get_and_ioremap_resource()
spi/omap100k:Fix PM disable depth imbalance in omap1_spi100k_probe
spi: dw: Fix PM disable depth imbalance in dw_spi_bt1_probe
spi: cadence-quadspi: Fix PM disable depth imbalance in cqspi_probe
spi: s3c24xx: Switch to use devm_spi_alloc_master()
spi: xilinx: Switch to use devm_spi_alloc_master()
spi: img-spfi: using pm_runtime_resume_and_get instead of pm_runtime_get_sync
spi: aspeed: Remove redundant dev_err call
spi: spi-mpc52xx: switch to using gpiod API
...
Merge changes regarding the management of ACPI device objects for
6.1-rc1:
- Rename ACPI device object reference counting functions (Rafael
Wysocki).
- Rearrange ACPI device object initialization code (Rafael Wysocki).
- Drop parent field from struct acpi_device (Rafael Wysocki).
- Extend the the int3472-tps68470 driver to support multiple consumers
of a single TPS68470 along with the requisite framework-level
support (Daniel Scally).
* acpi-dev:
platform/x86: int3472: Add board data for Surface Go2 IR camera
platform/x86: int3472: Support multiple gpio lookups in board data
platform/x86: int3472: Support multiple clock consumers
ACPI: bus: Add iterator for dependent devices
ACPI: scan: Add acpi_dev_get_next_consumer_dev()
ACPI: property: Use acpi_dev_parent()
ACPI: Drop redundant acpi_dev_parent() header
ACPI: PM: Fix NULL argument handling in acpi_device_get/set_power()
ACPI: Drop parent field from struct acpi_device
ACPI: scan: Eliminate __acpi_device_add()
ACPI: scan: Rearrange initialization of ACPI device objects
ACPI: scan: Rename acpi_bus_get_parent() and rearrange it
ACPI: Rename acpi_bus_get/put_acpi_device()
SPI code checks for non-zero sgt->orig_nents to determine if the buffer
has been DMA-mapped. Ensure that sg_table is really zeroed after free to
avoid potential NULL pointer dereference if the given SPI xfer object is
reused again without being DMA-mapped.
Fixes: 0c17ba73c08f ("spi: Fix cache corruption due to DMA/PIO overlap")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20220930113408.19720-1-m.szyprowski@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A couple of drivers call spi_split_transfers_maxsize() from their
->prepare_message() callbacks to split transfers which are too big for
them to handle. Add support in the core to do this based on
->max_transfer_size() to avoid code duplication.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20220927112117.77599-4-vincent.whitchurch@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPI core DMA mapping support performs cache management once for the
entire message and not between transfers, and this leads to cache
corruption if a message has two or more RX transfers with both
transfers targeting the same cache line, and the controller driver
decides to handle one using DMA and the other using PIO (for example,
because one is much larger than the other).
Fix it by syncing before/after the actual transfers. This also means
that we can skip the sync during the map/unmap of the message.
Fixes: 99adef310f68 ("spi: Provide core support for DMA mapping transfers")
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20220927112117.77599-3-vincent.whitchurch@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Save the current RX and TX DMA devices to avoid having to duplicate the
logic to pick them, since we'll need access to them in some more
functions to fix a bug in the cache handling.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20220927112117.77599-2-vincent.whitchurch@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Several fixes that came in since the merge window, the major one being a
fix for the spi-mux driver which was broken by the performance
optimisations due to it peering inside the core's data structures more
than it should.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmMZ22MACgkQJNaLcl1U
h9BV9Af/fvJZTo35a2NBZ6kUw/V+73LSxfEfzfzjqfXhYTTiYshDTvRi7MK+FdrU
E84vuidJkmP1+NVRbyoiBbDhx9Ejq11tHL8rpCm/0PTrSd3jc2WMs9ODGG0XIXst
j3Q7WnaWOfvvETSDVw8jNs8B9zdMMXsluaTJUIn1hjQWSVYTt67hsqtwRjrRlwmI
xLjVcYygnsiggNetAKCqmamPG9W94v6aUlhQ7c7aiAqYwQgy94sCBye+T4pV64rK
mF28RkdDx6U9TA08uSepmwgUC9PEWyCIsVSoJs0DuKXZH9WQ/ixsFDubC8WodIKT
/IgtX+Xpf6bES6n8fi3tidd7HkXrqw==
=ZJei
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"Several fixes that came in since the merge window, the major one being
a fix for the spi-mux driver which was broken by the performance
optimisations due to it peering inside the core's data structures more
than it should"
* tag 'spi-fix-v6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spi: Fix queue hang if previous transfer failed
spi: mux: Fix mux interaction with fast path optimisations
spi: cadence-quadspi: Disable irqs during indirect reads
spi: bitbang: Fix lsb-first Rx
