[ Upstream commit 633d76ad01 ]
The checks in question were introduced by:
commit 6b4db2e528 ("devlink: Fix use-after-free after a failed reload").
That fixed an issue of reload with mlxsw driver.
Back then, that was a valid fix, because there was a limitation
in place that prevented drivers from registering/unregistering params
when devlink instance was registered.
It was possible to do the fix differently by changing drivers to
register/unregister params in appropriate places making sure the ops
operate only on memory which is allocated and initialized. But that,
as a dependency, would require to remove the limitation mentioned above.
Eventually, this limitation was lifted by:
commit 1d18bb1a4d ("devlink: allow registering parameters after the instance")
Also, the alternative fix (which also fixed another issue) was done by:
commit 74cbc3c03c ("mlxsw: spectrum_acl_tcam: Move devlink param to TCAM code").
Therefore, the checks are no longer relevant. Each driver should make
sure to have the params registered only when the memory the ops
are working with is allocated and initialized.
So remove the checks.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0605d9fb41 ]
New Allwinner's SPI controllers can support dual and quad SPI modes.
To enable one of these modes, we should set the corresponding bit in
the SUN6I_BURST_CTL_CNT_REG register. DRM (28 bits) for dual mode and
Quad_EN (29 bits) for quad transmission.
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Link: https://lore.kernel.org/r/20230624131632.2972546-2-bigunclemax@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c5e490093 ]
If read() fails and returns -1 (or returns garbage for some other
reason) buf would be accessed out of bounds.
Only use the return value of read() after it has been validated.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c388c9920d ]
kernel parameters allow pass two types of strings, one type is like
'noapic', another type is like 'panic=5', the first type is passed as
arguments of the init program, the second type is passed as environment
variables of the init program.
when users pass kernel parameters like this:
noapic NOLIBC_TEST=syscall
our nolibc-test program will use the test setting from argv[1] and
ignore the one from NOLIBC_TEST environment variable, and at last, it
will print the following line and ignore the whole test setting.
Ignoring unknown test name 'noapic'
reversing the parsing order does solve the above issue:
test = getenv("NOLIBC_TEST");
if (test)
test = argv[1];
but it still doesn't work with such kernel parameters (without
NOLIBC_TEST environment variable):
noapic FOO=bar
To support all of the potential kernel parameters, let's verify the test
setting from both of argv[1] and NOLIBC_TEST environment variable.
Reviewed-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Zhangjin Wu <falcon@tinylab.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 883cf0d4cf ]
If a badly constructed firmware includes multiple `ACPI_TYPE_PACKAGE`
objects while evaluating the AMD LPS0 _DSM, there will be a memory
leak. Explicitly guard against this.
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d11a69873d ]
Arm platforms use is_default_overflow_handler() to determine if the
hw_breakpoint code should single-step over the breakpoint trigger or
let the custom handler deal with it.
Since bpf_overflow_handler() currently isn't recognized as a default
handler, attaching a BPF program to a PERF_TYPE_BREAKPOINT event causes
it to keep firing (the instruction triggering the data abort exception
is never skipped). For example:
# bpftrace -e 'watchpoint:0x10000:4:w { print("hit") }' -c ./test
Attaching 1 probe...
hit
hit
[...]
^C
(./test performs a single 4-byte store to 0x10000)
This patch replaces the check with uses_default_overflow_handler(),
which accounts for the bpf_overflow_handler() case by also testing
if one of the perf_event_output functions gets invoked indirectly,
via orig_default_handler.
Signed-off-by: Tomislav Novak <tnovak@meta.com>
Tested-by: Samuel Gosselin <sgosselin@google.com> # arm64
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/linux-arm-kernel/20220923203644.2731604-1-tnovak@fb.com/
Link: https://lore.kernel.org/r/20230605191923.1219974-1-tnovak@meta.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8cf04bb321 ]
Linux defaults to picking the non-working ACPI video backlight interface
on the Apple iMac12,1 and iMac12,2.
Add a DMI quirk to pick the working native radeon_bl0 interface instead.
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/1838
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2753
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e89ecd8368 ]
For i.MX8MP, we cannot ensure that cycle counter overflow occurs at least
4 times as often as other events. Due to byte counters will count for any
event configured, it will overflow more often. And if byte counters
overflow that related counters would stop since they share the
COUNTER_CNTL. We can speed up cycle counter overflow frequency by setting
counter parameter (CP) field of cycle counter. In this way, we can avoid
stop counting byte counters when interrupt didn't come and the byte
counters can be fetched or updated from each cycle counter overflow
interrupt.
Because we initialize CP filed to shorten counter0 overflow time, the cycle
counter will start couting from a fixed/base value each time. We need to
remove the base from the result too. Therefore, we could get precise result
from cycle counter.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20230811015438.1999307-1-xu.yang_2@nxp.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ddccc8a7d ]
The separate vmalloc area size check against _REGION2_SIZE
is needed in case user provided insanely large value using
vmalloc= kernel command line parameter. That could lead to
overflow and selecting 3 page table levels instead of 4.
Use size_add() for the overflow check and get rid of the
extra vmalloc area check.
With the current values of CONFIG_MAX_PHYSMEM_BITS and
PAGES_PER_SECTION the sum of maximal possible size of
identity mapping and vmemmap area (derived from these
macros) plus modules area size MODULES_LEN can not
overflow. Thus, that sum is used as first addend while
vmalloc area size is second addend for size_add().
Suggested-by: Heiko Carstens <hca@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0242737dc4 ]
Some HiSilicon SMMU PMCG suffers the erratum 162001900 that the PMU
disable control sometimes fail to disable the counters. This will lead
to error or inaccurate data since before we enable the counters the
counter's still counting for the event used in last perf session.
This patch tries to fix this by hardening the global disable process.
Before disable the PMU, writing an invalid event type (0xffff) to
focibly stop the counters. Correspondingly restore each events on
pmu::pmu_enable().
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Link: https://lore.kernel.org/r/20230814124012.58013-1-yangyicong@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f2d4dced9a ]
Remove the 1 second timeout applied to hw_protection_shutdown after an
EC panic. On some platforms this 1 second timeout is insufficient to
allow the filesystem to fully sync. Independently the EC will force a
full system reset after a short period. So this backup timeout is
unnecessary.
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Link: https://lore.kernel.org/r/20230802175847.1.Ie9fc53b6a1f4c6661c5376286a50e0cf51b3e961@changeid
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 96b709be18 ]
The Lenovo Ideapad Z470 predates Windows 8, so it defaults to using
acpi_video for backlight control. But this is not functional on this
model.
Add a DMI quirk to use the native backlight interface which works.
Link: https://bugzilla.suse.com/show_bug.cgi?id=1208724
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 013608cd08 ]
Kernels built with CONFIG_KASAN=y quarantine newly freed memory in order
to better detect use-after-free errors. However, this can exhaust memory
more quickly in allocator-heavy tests, which can result in spurious
scftorture failure. This commit therefore forgives memory-allocation
failure in kernels built with CONFIG_KASAN=y, but continues counting
the errors for use in detailed test-result analyses.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d243b34459 ]
Under PREEMPT_RT, __put_task_struct() indirectly acquires sleeping
locks. Therefore, it can't be called from an non-preemptible context.
One practical example is splat inside inactive_task_timer(), which is
called in a interrupt context:
CPU: 1 PID: 2848 Comm: life Kdump: loaded Tainted: G W ---------
Hardware name: HP ProLiant DL388p Gen8, BIOS P70 07/15/2012
Call Trace:
dump_stack_lvl+0x57/0x7d
mark_lock_irq.cold+0x33/0xba
mark_lock+0x1e7/0x400
mark_usage+0x11d/0x140
__lock_acquire+0x30d/0x930
lock_acquire.part.0+0x9c/0x210
rt_spin_lock+0x27/0xe0
refill_obj_stock+0x3d/0x3a0
kmem_cache_free+0x357/0x560
inactive_task_timer+0x1ad/0x340
__run_hrtimer+0x8a/0x1a0
__hrtimer_run_queues+0x91/0x130
hrtimer_interrupt+0x10f/0x220
__sysvec_apic_timer_interrupt+0x7b/0xd0
sysvec_apic_timer_interrupt+0x4f/0xd0
asm_sysvec_apic_timer_interrupt+0x12/0x20
RIP: 0033:0x7fff196bf6f5
Instead of calling __put_task_struct() directly, we defer it using
call_rcu(). A more natural approach would use a workqueue, but since
in PREEMPT_RT, we can't allocate dynamic memory from atomic context,
the code would become more complex because we would need to put the
work_struct instance in the task_struct and initialize it when we
allocate a new task_struct.
The issue is reproducible with stress-ng:
while true; do
stress-ng --sched deadline --sched-period 1000000000 \
--sched-runtime 800000000 --sched-deadline \
1000000000 --mmapfork 23 -t 20
done
Reported-by: Hu Chunyu <chuhu@redhat.com>
Suggested-by: Oleg Nesterov <oleg@redhat.com>
Suggested-by: Valentin Schneider <vschneid@redhat.com>
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Wander Lairson Costa <wander@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20230614122323.37957-2-wander@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a21ffdbc8 ]
ACPICA commit 90310989a0790032f5a0140741ff09b545af4bc5
According to the ACPI specification 19.6.134, no argument is required to be passed for ASL Timer instruction. For taking care of no argument, AML_NO_OPERAND_RESOLVE flag is added to ASL Timer instruction opcode.
When ASL timer instruction interpreted by ACPI interpreter, getting error. After adding AML_NO_OPERAND_RESOLVE flag to ASL Timer instruction opcode, issue is not observed.
=============================================================
UBSAN: array-index-out-of-bounds in acpica/dswexec.c:401:12 index -1 is out of range for type 'union acpi_operand_object *[9]'
CPU: 37 PID: 1678 Comm: cat Not tainted
6.0.0-dev-th500-6.0.y-1+bcf8c46459e407-generic-64k
HW name: NVIDIA BIOS v1.1.1-d7acbfc-dirty 12/19/2022 Call trace:
dump_backtrace+0xe0/0x130
show_stack+0x20/0x60
dump_stack_lvl+0x68/0x84
dump_stack+0x18/0x34
ubsan_epilogue+0x10/0x50
__ubsan_handle_out_of_bounds+0x80/0x90
acpi_ds_exec_end_op+0x1bc/0x6d8
acpi_ps_parse_loop+0x57c/0x618
acpi_ps_parse_aml+0x1e0/0x4b4
acpi_ps_execute_method+0x24c/0x2b8
acpi_ns_evaluate+0x3a8/0x4bc
acpi_evaluate_object+0x15c/0x37c
acpi_evaluate_integer+0x54/0x15c
show_power+0x8c/0x12c [acpi_power_meter]
Link: https://github.com/acpica/acpica/commit/90310989
Signed-off-by: Abhishek Mainkar <abmainkar@nvidia.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7f72f50547 ]
[BUG]
Syzbot reported several warning triggered inside
lookup_inline_extent_backref().
[CAUSE]
As usual, the reproducer doesn't reliably trigger locally here, but at
least we know the WARN_ON() is triggered when an inline backref can not
be found, and it can only be triggered when @insert is true. (I.e.
inserting a new inline backref, which means the backref should already
exist)
[ENHANCEMENT]
After the WARN_ON(), dump all the parameters and the extent tree
leaf to help debug.
Link: https://syzkaller.appspot.com/bug?extid=d6f9ff86c1d804ba2bc6
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 257614301a ]
[PROBLEM]
Inside function update_inline_extent_backref(), we have several
BUG_ON()s along with some ASSERT()s which can be triggered by corrupted
filesystem.
[ANAYLYSE]
Most of those BUG_ON()s and ASSERT()s are just a way of handling
unexpected on-disk data.
Although we have tree-checker to rule out obviously incorrect extent
tree blocks, it's not enough for these ones. Thus we need proper error
handling for them.
[FIX]
Thankfully all the callers of update_inline_extent_backref() would
eventually handle the errror by aborting the current transaction.
So this patch would do the proper error handling by:
- Make update_inline_extent_backref() to return int
The return value would be either 0 or -EUCLEAN.
- Replace BUG_ON()s and ASSERT()s with proper error handling
This includes:
* Dump the bad extent tree leaf
* Output an error message for the cause
This would include the extent bytenr, num_bytes (if needed), the bad
values and expected good values.
* Return -EUCLEAN
Note here we remove all the WARN_ON()s, as eventually the transaction
would be aborted, thus a backtrace would be triggered anyway.
- Better comments on why we expect refs == 1 and refs_to_mode == -1 for
tree blocks
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ccbe77f7e4 ]
Syzkaller reports a memory leak:
BUG: memory leak
unreferenced object 0xffff88810b279e00 (size 96):
comm "syz-executor399", pid 3631, jiffies 4294964921 (age 23.870s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 08 9e 27 0b 81 88 ff ff ..........'.....
08 9e 27 0b 81 88 ff ff 00 00 00 00 00 00 00 00 ..'.............
backtrace:
[<ffffffff814cfc90>] kmalloc_trace+0x20/0x90 mm/slab_common.c:1046
[<ffffffff81bb75ca>] kmalloc include/linux/slab.h:576 [inline]
[<ffffffff81bb75ca>] autofs_wait+0x3fa/0x9a0 fs/autofs/waitq.c:378
[<ffffffff81bb88a7>] autofs_do_expire_multi+0xa7/0x3e0 fs/autofs/expire.c:593
[<ffffffff81bb8c33>] autofs_expire_multi+0x53/0x80 fs/autofs/expire.c:619
[<ffffffff81bb6972>] autofs_root_ioctl_unlocked+0x322/0x3b0 fs/autofs/root.c:897
[<ffffffff81bb6a95>] autofs_root_ioctl+0x25/0x30 fs/autofs/root.c:910
[<ffffffff81602a9c>] vfs_ioctl fs/ioctl.c:51 [inline]
[<ffffffff81602a9c>] __do_sys_ioctl fs/ioctl.c:870 [inline]
[<ffffffff81602a9c>] __se_sys_ioctl fs/ioctl.c:856 [inline]
[<ffffffff81602a9c>] __x64_sys_ioctl+0xfc/0x140 fs/ioctl.c:856
[<ffffffff84608225>] do_syscall_x64 arch/x86/entry/common.c:50 [inline]
[<ffffffff84608225>] do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
[<ffffffff84800087>] entry_SYSCALL_64_after_hwframe+0x63/0xcd
autofs_wait_queue structs should be freed if their wait_ctr becomes zero.
Otherwise they will be lost.
In this case an AUTOFS_IOC_EXPIRE_MULTI ioctl is done, then a new
waitqueue struct is allocated in autofs_wait(), its initial wait_ctr
equals 2. After that wait_event_killable() is interrupted (it returns
-ERESTARTSYS), so that 'wq->name.name == NULL' condition may be not
satisfied. Actually, this condition can be satisfied when
autofs_wait_release() or autofs_catatonic_mode() is called and, what is
also important, wait_ctr is decremented in those places. Upon the exit of
autofs_wait(), wait_ctr is decremented to 1. Then the unmounting process
begins: kill_sb calls autofs_catatonic_mode(), which should have freed the
waitqueues, but it only decrements its usage counter to zero which is not
a correct behaviour.
edit:imk
This description is of course not correct. The umount performed as a result
of an expire is a umount of a mount that has been automounted, it's not the
autofs mount itself. They happen independently, usually after everything
mounted within the autofs file system has been expired away. If everything
hasn't been expired away the automount daemon can still exit leaving mounts
in place. But expires done in both cases will result in a notification that
calls autofs_wait_release() with a result status. The problem case is the
summary execution of of the automount daemon. In this case any waiting
processes won't be woken up until either they are terminated or the mount
is umounted.
end edit: imk
So in catatonic mode we should free waitqueues which counter becomes zero.
edit: imk
Initially I was concerned that the calling of autofs_wait_release() and
autofs_catatonic_mode() was not mutually exclusive but that can't be the
case (obviously) because the queue entry (or entries) is removed from the
list when either of these two functions are called. Consequently the wait
entry will be freed by only one of these functions or by the woken process
in autofs_wait() depending on the order of the calls.
end edit: imk
Reported-by: syzbot+5e53f70e69ff0c0a1c0c@syzkaller.appspotmail.com
Suggested-by: Takeshi Misawa <jeliantsurux@gmail.com>
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Ian Kent <raven@themaw.net>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Andrei Vagin <avagin@gmail.com>
Cc: autofs@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Message-Id: <169112719161.7590.6700123246297365841.stgit@donald.themaw.net>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eee2d2e6ea ]
folio_next_index() returns an unsigned long value which left shifted
by PAGE_SHIFT could possibly cause an overflow on 32-bit system. Instead
use folio_pos(folio) + folio_size(folio), which does this correctly.
Suggested-by: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Ritesh Harjani (IBM) <ritesh.list@gmail.com>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3d028d5d60 upstream.
[WHY]
Currently, when insert_plane is called with insert_above_mpcc
parameter that is equal to tree->opp_list, the function returns NULL.
[HOW]
Instead, the function should insert the plane at the top of the tree.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Wesley Chalmers <wesley.chalmers@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3cec504909 upstream.
Commit 408579cd62 ("mm: Update do_vmi_align_munmap() return
semantics") seems to have updated one of the callers of do_vmi_munmap()
incorrectly: it used to check for the error case (which didn't
change: negative means error).
That commit changed the check to the success case (which did change:
before that commit, 0 was success, and 1 was "success and lock
downgraded". After the change, it's always 0 for success, and the lock
will have been released if requested).
This didn't change any actual VM behavior _except_ for memory accounting
when 'VM_ACCOUNT' was set on the vma. Which made the wrong return value
test fairly subtle, since everything continues to work.
Or rather - it continues to work but the "Committed memory" accounting
goes all wonky (Committed_AS value in /proc/meminfo), and depending on
settings that then causes problems much much later as the VM relies on
bogus statistics for its heuristics.
Revert that one line of the change back to the original logic.
Fixes: 408579cd62 ("mm: Update do_vmi_align_munmap() return semantics")
Reported-by: Christoph Biedl <linux-kernel.bfrz@manchmal.in-ulm.de>
Reported-bisected-and-tested-by: Michael Labiuk <michael.labiuk@virtuozzo.com>
Cc: Bagas Sanjaya <bagasdotme@gmail.com>
Cc: Liam R. Howlett <Liam.Howlett@oracle.com>
Link: https://lore.kernel.org/all/1694366957@msgid.manchmal.in-ulm.de/
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a22730b1b4 ]
syzkaller found a memory leak in kcm_sendmsg(), and commit c821a88bd7
("kcm: Fix memory leak in error path of kcm_sendmsg()") suppressed it by
updating kcm_tx_msg(head)->last_skb if partial data is copied so that the
following sendmsg() will resume from the skb.
However, we cannot know how many bytes were copied when we get the error.
Thus, we could mess up the MSG_MORE queue.
When kcm_sendmsg() fails for SOCK_DGRAM, we should purge the queue as we
do so for UDP by udp_flush_pending_frames().
Even without this change, when the error occurred, the following sendmsg()
resumed from a wrong skb and the queue was messed up. However, we have
yet to get such a report, and only syzkaller stumbled on it. So, this
can be changed safely.
Note this does not change SOCK_SEQPACKET behaviour.
Fixes: c821a88bd7 ("kcm: Fix memory leak in error path of kcm_sendmsg()")
Fixes: ab7ac4eb98 ("kcm: Kernel Connection Multiplexor module")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20230912022753.33327-1-kuniyu@amazon.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc6ed2fa24 ]
After commit 50f303496d ("igb: Enable SR-IOV after reinit"), removing
the igb module could hang or crash (depending on the machine) when the
module has been loaded with the max_vfs parameter set to some value != 0.
In case of one test machine with a dual port 82580, this hang occurred:
[ 232.480687] igb 0000:41:00.1: removed PHC on enp65s0f1
[ 233.093257] igb 0000:41:00.1: IOV Disabled
[ 233.329969] pcieport 0000:40:01.0: AER: Multiple Uncorrected (Non-Fatal) err0
[ 233.340302] igb 0000:41:00.0: PCIe Bus Error: severity=Uncorrected (Non-Fata)
[ 233.352248] igb 0000:41:00.0: device [8086:1516] error status/mask=00100000
[ 233.361088] igb 0000:41:00.0: [20] UnsupReq (First)
[ 233.368183] igb 0000:41:00.0: AER: TLP Header: 40000001 0000040f cdbfc00c c
[ 233.376846] igb 0000:41:00.1: PCIe Bus Error: severity=Uncorrected (Non-Fata)
[ 233.388779] igb 0000:41:00.1: device [8086:1516] error status/mask=00100000
[ 233.397629] igb 0000:41:00.1: [20] UnsupReq (First)
[ 233.404736] igb 0000:41:00.1: AER: TLP Header: 40000001 0000040f cdbfc00c c
[ 233.538214] pci 0000:41:00.1: AER: can't recover (no error_detected callback)
[ 233.538401] igb 0000:41:00.0: removed PHC on enp65s0f0
[ 233.546197] pcieport 0000:40:01.0: AER: device recovery failed
[ 234.157244] igb 0000:41:00.0: IOV Disabled
[ 371.619705] INFO: task irq/35-aerdrv:257 blocked for more than 122 seconds.
[ 371.627489] Not tainted 6.4.0-dirty #2
[ 371.632257] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this.
[ 371.641000] task:irq/35-aerdrv state:D stack:0 pid:257 ppid:2 f0
[ 371.650330] Call Trace:
[ 371.653061] <TASK>
[ 371.655407] __schedule+0x20e/0x660
[ 371.659313] schedule+0x5a/0xd0
[ 371.662824] schedule_preempt_disabled+0x11/0x20
[ 371.667983] __mutex_lock.constprop.0+0x372/0x6c0
[ 371.673237] ? __pfx_aer_root_reset+0x10/0x10
[ 371.678105] report_error_detected+0x25/0x1c0
[ 371.682974] ? __pfx_report_normal_detected+0x10/0x10
[ 371.688618] pci_walk_bus+0x72/0x90
[ 371.692519] pcie_do_recovery+0xb2/0x330
[ 371.696899] aer_process_err_devices+0x117/0x170
[ 371.702055] aer_isr+0x1c0/0x1e0
[ 371.705661] ? __set_cpus_allowed_ptr+0x54/0xa0
[ 371.710723] ? __pfx_irq_thread_fn+0x10/0x10
[ 371.715496] irq_thread_fn+0x20/0x60
[ 371.719491] irq_thread+0xe6/0x1b0
[ 371.723291] ? __pfx_irq_thread_dtor+0x10/0x10
[ 371.728255] ? __pfx_irq_thread+0x10/0x10
[ 371.732731] kthread+0xe2/0x110
[ 371.736243] ? __pfx_kthread+0x10/0x10
[ 371.740430] ret_from_fork+0x2c/0x50
[ 371.744428] </TASK>
The reproducer was a simple script:
#!/bin/sh
for i in `seq 1 5`; do
modprobe -rv igb
modprobe -v igb max_vfs=1
sleep 1
modprobe -rv igb
done
It turned out that this could only be reproduce on 82580 (quad and
dual-port), but not on 82576, i350 and i210. Further debugging showed
that igb_enable_sriov()'s call to pci_enable_sriov() is failing, because
dev->is_physfn is 0 on 82580.
Prior to commit 50f303496d ("igb: Enable SR-IOV after reinit"),
igb_enable_sriov() jumped into the "err_out" cleanup branch. After this
commit it only returned the error code.
So the cleanup didn't take place, and the incorrect VF setup in the
igb_adapter structure fooled the igb driver into assuming that VFs have
been set up where no VF actually existed.
Fix this problem by cleaning up again if pci_enable_sriov() fails.
Fixes: 50f303496d ("igb: Enable SR-IOV after reinit")
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Reviewed-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c44191dd7 ]
The commit in fixes introduced flags to control the status of hardware
configuration while processing packets. At the same time another structure
is used to provide configuration of timestamper to user-space applications.
The way it was coded makes this structures go out of sync easily. The
repro is easy for 82599 chips:
[root@hostname ~]# hwstamp_ctl -i eth0 -r 12 -t 1
current settings:
tx_type 0
rx_filter 0
new settings:
tx_type 1
rx_filter 12
The eth0 device is properly configured to timestamp any PTPv2 events.
[root@hostname ~]# hwstamp_ctl -i eth0 -r 1 -t 1
current settings:
tx_type 1
rx_filter 12
SIOCSHWTSTAMP failed: Numerical result out of range
The requested time stamping mode is not supported by the hardware.
The error is properly returned because HW doesn't support all packets
timestamping. But the adapter->flags is cleared of timestamp flags
even though no HW configuration was done. From that point no RX timestamps
are received by user-space application. But configuration shows good
values:
[root@hostname ~]# hwstamp_ctl -i eth0
current settings:
tx_type 1
rx_filter 12
Fix the issue by applying new flags only when the HW was actually
configured.
Fixes: a9763f3cb5 ("ixgbe: Update PTP to support X550EM_x devices")
Signed-off-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0071d15517 ]
The selftest passes the IPv6 address length for an IPv4 address.
We should pass the correct length.
Note inet_bind_sk() does not check if the size is larger than
sizeof(struct sockaddr_in), so there is no real bug in this
selftest.
Fixes: 13715acf8a ("selftest: Add test for bind() conflicts.")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c48ef9c4ae ]
Since bhash2 was introduced, the example below does not work as expected.
These two bind() should conflict, but the 2nd bind() now succeeds.
from socket import *
s1 = socket(AF_INET6, SOCK_STREAM)
s1.bind(('::ffff:127.0.0.1', 0))
s2 = socket(AF_INET, SOCK_STREAM)
s2.bind(('127.0.0.1', s1.getsockname()[1]))
During the 2nd bind() in inet_csk_get_port(), inet_bind2_bucket_find()
fails to find the 1st socket's tb2, so inet_bind2_bucket_create() allocates
a new tb2 for the 2nd socket. Then, we call inet_csk_bind_conflict() that
checks conflicts in the new tb2 by inet_bhash2_conflict(). However, the
new tb2 does not include the 1st socket, thus the bind() finally succeeds.
In this case, inet_bind2_bucket_match() must check if AF_INET6 tb2 has
the conflicting v4-mapped-v6 address so that inet_bind2_bucket_find()
returns the 1st socket's tb2.
Note that if we bind two sockets to 127.0.0.1 and then ::FFFF:127.0.0.1,
the 2nd bind() fails properly for the same reason mentinoed in the previous
commit.
Fixes: 28044fc1d4 ("net: Add a bhash2 table hashed by port and address")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Andrei Vagin <avagin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa99e5f87b ]
Andrei Vagin reported bind() regression with strace logs.
If we bind() a TCPv6 socket to ::FFFF:0.0.0.0 and then bind() a TCPv4
socket to 127.0.0.1, the 2nd bind() should fail but now succeeds.
from socket import *
s1 = socket(AF_INET6, SOCK_STREAM)
s1.bind(('::ffff:0.0.0.0', 0))
s2 = socket(AF_INET, SOCK_STREAM)
s2.bind(('127.0.0.1', s1.getsockname()[1]))
During the 2nd bind(), if tb->family is AF_INET6 and sk->sk_family is
AF_INET in inet_bind2_bucket_match_addr_any(), we still need to check
if tb has the v4-mapped-v6 wildcard address.
The example above does not work after commit 5456262d2b ("net: Fix
incorrect address comparison when searching for a bind2 bucket"), but
the blamed change is not the commit.
Before the commit, the leading zeros of ::FFFF:0.0.0.0 were treated
as 0.0.0.0, and the sequence above worked by chance. Technically, this
case has been broken since bhash2 was introduced.
Note that if we bind() two sockets to 127.0.0.1 and then ::FFFF:0.0.0.0,
the 2nd bind() fails properly because we fall back to using bhash to
detect conflicts for the v4-mapped-v6 address.
Fixes: 28044fc1d4 ("net: Add a bhash2 table hashed by port and address")
Reported-by: Andrei Vagin <avagin@google.com>
Closes: https://lore.kernel.org/netdev/ZPuYBOFC8zsK6r9T@google.com/
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c6d277064b ]
This is a prep patch to make the following patches cleaner that touch
inet_bind2_bucket_match() and inet_bind2_bucket_match_addr_any().
Both functions have duplicated comparison for netns, port, and l3mdev.
Let's factorise them.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: aa99e5f87b ("tcp: Fix bind() regression for v4-mapped-v6 wildcard address.")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8cdd9f1aae ]
ip6_sock_set_addr_preferences() second argument should be an integer.
SUNRPC attempts to set IPV6_PREFER_SRC_PUBLIC were
translated to IPV6_PREFER_SRC_TMP
Fixes: 18d5ad6232 ("ipv6: add ip6_sock_set_addr_preferences")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230911154213.713941-1-edumazet@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a6102aa6d ]
There's an early return in veth_set_features() if the device is in a down
state, which leads to the XDP feature flags not being updated when enabling
GRO while the device is down. Which in turn leads to XDP_REDIRECT not
working, because the redirect code now checks the flags.
Fix this by updating the feature flags after bringing the device up.
Before this patch:
NETDEV_XDP_ACT_BASIC: yes
NETDEV_XDP_ACT_REDIRECT: yes
NETDEV_XDP_ACT_NDO_XMIT: no
NETDEV_XDP_ACT_XSK_ZEROCOPY: no
NETDEV_XDP_ACT_HW_OFFLOAD: no
NETDEV_XDP_ACT_RX_SG: yes
NETDEV_XDP_ACT_NDO_XMIT_SG: no
After this patch:
NETDEV_XDP_ACT_BASIC: yes
NETDEV_XDP_ACT_REDIRECT: yes
NETDEV_XDP_ACT_NDO_XMIT: yes
NETDEV_XDP_ACT_XSK_ZEROCOPY: no
NETDEV_XDP_ACT_HW_OFFLOAD: no
NETDEV_XDP_ACT_RX_SG: yes
NETDEV_XDP_ACT_NDO_XMIT_SG: yes
Fixes: fccca038f3 ("veth: take into account device reconfiguration for xdp_features flag")
Fixes: 66c0e13ad2 ("drivers: net: turn on XDP features")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20230911135826.722295-1-toke@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 403f0e7714 ]
macb_set_tx_clk() is called under a spinlock but itself calls clk_set_rate()
which can sleep. This results in:
| BUG: sleeping function called from invalid context at kernel/locking/mutex.c:580
| pps pps1: new PPS source ptp1
| in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 40, name: kworker/u4:3
| preempt_count: 1, expected: 0
| RCU nest depth: 0, expected: 0
| 4 locks held by kworker/u4:3/40:
| #0: ffff000003409148
| macb ff0c0000.ethernet: gem-ptp-timer ptp clock registered.
| ((wq_completion)events_power_efficient){+.+.}-{0:0}, at: process_one_work+0x14c/0x51c
| #1: ffff8000833cbdd8 ((work_completion)(&pl->resolve)){+.+.}-{0:0}, at: process_one_work+0x14c/0x51c
| #2: ffff000004f01578 (&pl->state_mutex){+.+.}-{4:4}, at: phylink_resolve+0x44/0x4e8
| #3: ffff000004f06f50 (&bp->lock){....}-{3:3}, at: macb_mac_link_up+0x40/0x2ac
| irq event stamp: 113998
| hardirqs last enabled at (113997): [<ffff800080e8503c>] _raw_spin_unlock_irq+0x30/0x64
| hardirqs last disabled at (113998): [<ffff800080e84478>] _raw_spin_lock_irqsave+0xac/0xc8
| softirqs last enabled at (113608): [<ffff800080010630>] __do_softirq+0x430/0x4e4
| softirqs last disabled at (113597): [<ffff80008001614c>] ____do_softirq+0x10/0x1c
| CPU: 0 PID: 40 Comm: kworker/u4:3 Not tainted 6.5.0-11717-g9355ce8b2f50-dirty #368
| Hardware name: ... ZynqMP ... (DT)
| Workqueue: events_power_efficient phylink_resolve
| Call trace:
| dump_backtrace+0x98/0xf0
| show_stack+0x18/0x24
| dump_stack_lvl+0x60/0xac
| dump_stack+0x18/0x24
| __might_resched+0x144/0x24c
| __might_sleep+0x48/0x98
| __mutex_lock+0x58/0x7b0
| mutex_lock_nested+0x24/0x30
| clk_prepare_lock+0x4c/0xa8
| clk_set_rate+0x24/0x8c
| macb_mac_link_up+0x25c/0x2ac
| phylink_resolve+0x178/0x4e8
| process_one_work+0x1ec/0x51c
| worker_thread+0x1ec/0x3e4
| kthread+0x120/0x124
| ret_from_fork+0x10/0x20
The obvious fix is to move the call to macb_set_tx_clk() out of the
protected area. This seems safe as rx and tx are both disabled anyway at
this point.
It is however not entirely clear what the spinlock shall protect. It
could be the read-modify-write access to the NCFGR register, but this
is accessed in macb_set_rx_mode() and macb_set_rxcsum_feature() as well
without holding the spinlock. It could also be the register accesses
done in mog_init_rings() or macb_init_buffers(), but again these
functions are called without holding the spinlock in macb_hresp_error_task().
The locking seems fishy in this driver and it might deserve another look
before this patch is applied.
Fixes: 633e98a711 ("net: macb: use resolved link config in mac_link_up()")
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20230908112913.1701766-1-s.hauer@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cfaa80c91f ]
I got the below warning when do fuzzing test:
BUG: KASAN: null-ptr-deref in scatterwalk_copychunks+0x320/0x470
Read of size 4 at addr 0000000000000008 by task kworker/u8:1/9
CPU: 0 PID: 9 Comm: kworker/u8:1 Tainted: G OE
Hardware name: linux,dummy-virt (DT)
Workqueue: pencrypt_parallel padata_parallel_worker
Call trace:
dump_backtrace+0x0/0x420
show_stack+0x34/0x44
dump_stack+0x1d0/0x248
__kasan_report+0x138/0x140
kasan_report+0x44/0x6c
__asan_load4+0x94/0xd0
scatterwalk_copychunks+0x320/0x470
skcipher_next_slow+0x14c/0x290
skcipher_walk_next+0x2fc/0x480
skcipher_walk_first+0x9c/0x110
skcipher_walk_aead_common+0x380/0x440
skcipher_walk_aead_encrypt+0x54/0x70
ccm_encrypt+0x13c/0x4d0
crypto_aead_encrypt+0x7c/0xfc
pcrypt_aead_enc+0x28/0x84
padata_parallel_worker+0xd0/0x2dc
process_one_work+0x49c/0xbdc
worker_thread+0x124/0x880
kthread+0x210/0x260
ret_from_fork+0x10/0x18
This is because the value of rec_seq of tls_crypto_info configured by the
user program is too large, for example, 0xffffffffffffff. In addition, TLS
is asynchronously accelerated. When tls_do_encryption() returns
-EINPROGRESS and sk->sk_err is set to EBADMSG due to rec_seq overflow,
skmsg is released before the asynchronous encryption process ends. As a
result, the UAF problem occurs during the asynchronous processing of the
encryption module.
If the operation is asynchronous and the encryption module returns
EINPROGRESS, do not free the record information.
Fixes: 635d939817 ("net/tls: free record only on encryption error")
Signed-off-by: Liu Jian <liujian56@huawei.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://lore.kernel.org/r/20230909081434.2324940-1-liujian56@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a138f1670 ]
The only probing method supported by the Nvidia SN2201 platform driver
is probing through an ACPI match table. Hence add a dependency on
ACPI, to prevent asking the user about this driver when configuring a
kernel without ACPI support.
Fixes: 662f24826f ("platform/mellanox: Add support for new SN2201 system")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Vadim Pasternak <vadimp@nvidia.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/ec5a4071691ab08d58771b7732a9988e89779268.1693828363.git.geert+renesas@glider.be
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f5969452e ]
This fix involves 2 changes:
- All event regs have a reset value of 0, which is not a valid
event_number as per the event_list for most blocks and hence seen
as an error. Add a "disable" event with event_number 0 for all blocks.
- The enable bit for each counter need not be checked before
reading the event info, and hence removed.
Fixes: 1a218d312e ("platform/mellanox: mlxbf-pmc: Add Mellanox BlueField PMC driver")
Signed-off-by: Shravan Kumar Ramani <shravankr@nvidia.com>
Reviewed-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: David Thompson <davthompson@nvidia.com>
Link: https://lore.kernel.org/r/04d0213932d32681de1c716b54320ed894e52425.1693917738.git.shravankr@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78034cbece ]
This commit fixes tmfifo console stuck issue when the virtual
networking interface is in down state. In such case, the network
Rx descriptors runs out and causes the Rx network packet staying
in the head of the tmfifo thus blocking the console packets. The
fix is to drop the Rx network packet when no more Rx descriptors.
Function name mlxbf_tmfifo_release_pending_pkt() is also renamed
to mlxbf_tmfifo_release_pkt() to be more approperiate.
Fixes: 1357dfd726 ("platform/mellanox: Add TmFifo driver for Mellanox BlueField Soc")
Signed-off-by: Liming Sun <limings@nvidia.com>
Reviewed-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: David Thompson <davthompson@nvidia.com>
Link: https://lore.kernel.org/r/8c0177dc938ae03f52ff7e0b62dbeee74b7bec09.1693322547.git.limings@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7b8d60b37 ]
According to the document of napi, there is no rx process when the
budget is 0. Therefore, r8152_poll() has to return 0 directly when the
budget is equal to 0.
Fixes: d2187f8e44 ("r8152: divide the tx and rx bottom functions")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86899e9e1e ]
Currently, when we add the first sja1105 port to a bridge with
vlan_filtering 1, then we sometimes see this output:
sja1105 spi2.2: port 4 failed to read back entry for be:79:b4:9e:9e:96 vid 3088: -ENOENT
sja1105 spi2.2: Reset switch and programmed static config. Reason: VLAN filtering
sja1105 spi2.2: port 0 failed to add be:79:b4:9e:9e:96 vid 0 to fdb: -2
It is because sja1105_fdb_add() runs from the dsa_owq which is no longer
serialized with switch resets since it dropped the rtnl_lock() in the
blamed commit.
Either performing the FDB accesses before the reset, or after the reset,
is equally fine, because sja1105_static_fdb_change() backs up those
changes in the static config, but FDB access during reset isn't ok.
Make sja1105_static_config_reload() take the fdb_lock to fix that.
Fixes: 0faf890fc5 ("net: dsa: drop rtnl_lock from dsa_slave_switchdev_event_work")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea32690daf ]
sja1105_fdb_add() runs from the dsa_owq, and sja1105_port_mcast_flood()
runs from switchdev_deferred_process_work(). Prior to the blamed commit,
they used to be indirectly serialized through the rtnl_lock(), which
no longer holds true because dsa_owq dropped that.
So, it is now possible that we traverse the static config BLK_IDX_L2_LOOKUP
elements concurrently compared to when we change them, in
sja1105_static_fdb_change(). That is not ideal, since it might result in
data corruption.
Introduce a mutex which serializes accesses to the hardware FDB and to
the static config elements for the L2 Address Lookup table.
I can't find a good reason to add locking around sja1105_fdb_dump().
I'll add it later if needed.
Fixes: 0faf890fc5 ("net: dsa: drop rtnl_lock from dsa_slave_switchdev_event_work")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7cef293b9a ]
The commit cited in Fixes: did 2 things: it refactored the read-back
polling from sja1105_dynamic_config_read() into a new function,
sja1105_dynamic_config_wait_complete(), and it called that from
sja1105_dynamic_config_write() too.
What is problematic is the refactoring.
The refactored code from sja1105_dynamic_config_poll_valid() works like
the previous one, but the problem is that it uses another packed_buf[]
SPI buffer, and there was code at the end of sja1105_dynamic_config_read()
which was relying on the read-back packed_buf[]:
/* Don't dereference possibly NULL pointer - maybe caller
* only wanted to see whether the entry existed or not.
*/
if (entry)
ops->entry_packing(packed_buf, entry, UNPACK);
After the change, the packed_buf[] that this code sees is no longer the
entry read back from hardware, but the original entry that the caller
passed to the sja1105_dynamic_config_read(), packed into this buffer.
This difference is the most notable with the SJA1105_SEARCH uses from
sja1105pqrs_fdb_add() - used for both fdb and mdb. There, we have logic
added by commit 728db843df ("net: dsa: sja1105: ignore the FDB entry
for unknown multicast when adding a new address") to figure out whether
the address we're trying to add matches on any existing hardware entry,
with the exception of the catch-all multicast address.
That logic was broken, because with sja1105_dynamic_config_read() not
working properly, it doesn't return us the entry read back from
hardware, but the entry that we passed to it. And, since for multicast,
a match will always exist, it will tell us that any mdb entry already
exists at index=0 L2 Address Lookup table. It is index=0 because the
caller doesn't know the index - it wants to find it out, and
sja1105_dynamic_config_read() does:
if (index < 0) { // SJA1105_SEARCH
/* Avoid copying a signed negative number to an u64 */
cmd.index = 0; // <- this
cmd.search = true;
} else {
cmd.index = index;
cmd.search = false;
}
So, to the caller of sja1105_dynamic_config_read(), the returned info
looks entirely legit, and it will add all mdb entries to FDB index 0.
There, they will always overwrite each other (not to mention,
potentially they can also overwrite a pre-existing bridge fdb entry),
and the user-visible impact will be that only the last mdb entry will be
forwarded as it should. The others won't (will be flooded or dropped,
depending on the egress flood settings).
Fixing is a bit more complicated, and involves either passing the same
packed_buf[] to sja1105_dynamic_config_wait_complete(), or moving all
the extra processing on the packed_buf[] to
sja1105_dynamic_config_wait_complete(). I've opted for the latter,
because it makes sja1105_dynamic_config_wait_complete() a bit more
self-contained.
Fixes: df405910ab ("net: dsa: sja1105: wait for dynamic config command completion on writes too")
Reported-by: Yanan Yang <yanan.yang@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c956798062 ]
Currently, sja1105_dynamic_config_wait_complete() returns either 0 or
-ETIMEDOUT, because it just looks at the read_poll_timeout() return code.
There will be future changes which move some more checks to
sja1105_dynamic_config_poll_valid(). It is important that we propagate
their exact return code (-ENOENT, -EINVAL), because callers of
sja1105_dynamic_config_read() depend on them.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 7cef293b9a ("net: dsa: sja1105: fix multicast forwarding working only for last added mdb entry")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 02c652f546 ]
Commit 4d94235495 ("net: dsa: sja1105: offload bridge port flags to
device") has partially hidden some multicast entries from showing up in
the "bridge fdb show" output, but it wasn't enough. Addresses which are
added through "bridge mdb add" still show up. Hide them all.
Fixes: 291d1e72b7 ("net: dsa: sja1105: Add support for FDB and MDB management")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
