mirror of
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git
synced 2025-01-09 22:50:41 +00:00
749396cb29
The DT of_device.h and of_platform.h date back to the separate of_platform_bus_type before it as merged into the regular platform bus. As part of that merge prepping Arm DT support 13 years ago, they "temporarily" include each other. They also include platform_device.h and of.h. As a result, there's a pretty much random mix of those include files used throughout the tree. In order to detangle these headers and replace the implicit includes with struct declarations, users need to explicitly include the correct includes. Signed-off-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20230714174955.4064174-1-robh@kernel.org Signed-off-by: Mark Brown <broonie@kernel.org>
873 lines
22 KiB
C
873 lines
22 KiB
C
// SPDX-License-Identifier: GPL-2.0
|
|
// Copyright (c) 2017-2018, The Linux foundation. All rights reserved.
|
|
|
|
#include <linux/clk.h>
|
|
#include <linux/dmapool.h>
|
|
#include <linux/dma-mapping.h>
|
|
#include <linux/interconnect.h>
|
|
#include <linux/interrupt.h>
|
|
#include <linux/io.h>
|
|
#include <linux/module.h>
|
|
#include <linux/of.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/pinctrl/consumer.h>
|
|
#include <linux/pm_runtime.h>
|
|
#include <linux/pm_opp.h>
|
|
#include <linux/spi/spi.h>
|
|
#include <linux/spi/spi-mem.h>
|
|
|
|
|
|
#define QSPI_NUM_CS 2
|
|
#define QSPI_BYTES_PER_WORD 4
|
|
|
|
#define MSTR_CONFIG 0x0000
|
|
#define FULL_CYCLE_MODE BIT(3)
|
|
#define FB_CLK_EN BIT(4)
|
|
#define PIN_HOLDN BIT(6)
|
|
#define PIN_WPN BIT(7)
|
|
#define DMA_ENABLE BIT(8)
|
|
#define BIG_ENDIAN_MODE BIT(9)
|
|
#define SPI_MODE_MSK 0xc00
|
|
#define SPI_MODE_SHFT 10
|
|
#define CHIP_SELECT_NUM BIT(12)
|
|
#define SBL_EN BIT(13)
|
|
#define LPA_BASE_MSK 0x3c000
|
|
#define LPA_BASE_SHFT 14
|
|
#define TX_DATA_DELAY_MSK 0xc0000
|
|
#define TX_DATA_DELAY_SHFT 18
|
|
#define TX_CLK_DELAY_MSK 0x300000
|
|
#define TX_CLK_DELAY_SHFT 20
|
|
#define TX_CS_N_DELAY_MSK 0xc00000
|
|
#define TX_CS_N_DELAY_SHFT 22
|
|
#define TX_DATA_OE_DELAY_MSK 0x3000000
|
|
#define TX_DATA_OE_DELAY_SHFT 24
|
|
|
|
#define AHB_MASTER_CFG 0x0004
|
|
#define HMEM_TYPE_START_MID_TRANS_MSK 0x7
|
|
#define HMEM_TYPE_START_MID_TRANS_SHFT 0
|
|
#define HMEM_TYPE_LAST_TRANS_MSK 0x38
|
|
#define HMEM_TYPE_LAST_TRANS_SHFT 3
|
|
#define USE_HMEMTYPE_LAST_ON_DESC_OR_CHAIN_MSK 0xc0
|
|
#define USE_HMEMTYPE_LAST_ON_DESC_OR_CHAIN_SHFT 6
|
|
#define HMEMTYPE_READ_TRANS_MSK 0x700
|
|
#define HMEMTYPE_READ_TRANS_SHFT 8
|
|
#define HSHARED BIT(11)
|
|
#define HINNERSHARED BIT(12)
|
|
|
|
#define MSTR_INT_EN 0x000C
|
|
#define MSTR_INT_STATUS 0x0010
|
|
#define RESP_FIFO_UNDERRUN BIT(0)
|
|
#define RESP_FIFO_NOT_EMPTY BIT(1)
|
|
#define RESP_FIFO_RDY BIT(2)
|
|
#define HRESP_FROM_NOC_ERR BIT(3)
|
|
#define WR_FIFO_EMPTY BIT(9)
|
|
#define WR_FIFO_FULL BIT(10)
|
|
#define WR_FIFO_OVERRUN BIT(11)
|
|
#define TRANSACTION_DONE BIT(16)
|
|
#define DMA_CHAIN_DONE BIT(31)
|
|
#define QSPI_ERR_IRQS (RESP_FIFO_UNDERRUN | HRESP_FROM_NOC_ERR | \
|
|
WR_FIFO_OVERRUN)
|
|
#define QSPI_ALL_IRQS (QSPI_ERR_IRQS | RESP_FIFO_RDY | \
|
|
WR_FIFO_EMPTY | WR_FIFO_FULL | \
|
|
TRANSACTION_DONE)
|
|
|
|
#define PIO_XFER_CTRL 0x0014
|
|
#define REQUEST_COUNT_MSK 0xffff
|
|
|
|
#define PIO_XFER_CFG 0x0018
|
|
#define TRANSFER_DIRECTION BIT(0)
|
|
#define MULTI_IO_MODE_MSK 0xe
|
|
#define MULTI_IO_MODE_SHFT 1
|
|
#define TRANSFER_FRAGMENT BIT(8)
|
|
#define SDR_1BIT 1
|
|
#define SDR_2BIT 2
|
|
#define SDR_4BIT 3
|
|
#define DDR_1BIT 5
|
|
#define DDR_2BIT 6
|
|
#define DDR_4BIT 7
|
|
#define DMA_DESC_SINGLE_SPI 1
|
|
#define DMA_DESC_DUAL_SPI 2
|
|
#define DMA_DESC_QUAD_SPI 3
|
|
|
|
#define PIO_XFER_STATUS 0x001c
|
|
#define WR_FIFO_BYTES_MSK 0xffff0000
|
|
#define WR_FIFO_BYTES_SHFT 16
|
|
|
|
#define PIO_DATAOUT_1B 0x0020
|
|
#define PIO_DATAOUT_4B 0x0024
|
|
|
|
#define RD_FIFO_CFG 0x0028
|
|
#define CONTINUOUS_MODE BIT(0)
|
|
|
|
#define RD_FIFO_STATUS 0x002c
|
|
#define FIFO_EMPTY BIT(11)
|
|
#define WR_CNTS_MSK 0x7f0
|
|
#define WR_CNTS_SHFT 4
|
|
#define RDY_64BYTE BIT(3)
|
|
#define RDY_32BYTE BIT(2)
|
|
#define RDY_16BYTE BIT(1)
|
|
#define FIFO_RDY BIT(0)
|
|
|
|
#define RD_FIFO_RESET 0x0030
|
|
#define RESET_FIFO BIT(0)
|
|
|
|
#define NEXT_DMA_DESC_ADDR 0x0040
|
|
#define CURRENT_DMA_DESC_ADDR 0x0044
|
|
#define CURRENT_MEM_ADDR 0x0048
|
|
|
|
#define CUR_MEM_ADDR 0x0048
|
|
#define HW_VERSION 0x004c
|
|
#define RD_FIFO 0x0050
|
|
#define SAMPLING_CLK_CFG 0x0090
|
|
#define SAMPLING_CLK_STATUS 0x0094
|
|
|
|
#define QSPI_ALIGN_REQ 32
|
|
|
|
enum qspi_dir {
|
|
QSPI_READ,
|
|
QSPI_WRITE,
|
|
};
|
|
|
|
struct qspi_cmd_desc {
|
|
u32 data_address;
|
|
u32 next_descriptor;
|
|
u32 direction:1;
|
|
u32 multi_io_mode:3;
|
|
u32 reserved1:4;
|
|
u32 fragment:1;
|
|
u32 reserved2:7;
|
|
u32 length:16;
|
|
};
|
|
|
|
struct qspi_xfer {
|
|
union {
|
|
const void *tx_buf;
|
|
void *rx_buf;
|
|
};
|
|
unsigned int rem_bytes;
|
|
unsigned int buswidth;
|
|
enum qspi_dir dir;
|
|
bool is_last;
|
|
};
|
|
|
|
enum qspi_clocks {
|
|
QSPI_CLK_CORE,
|
|
QSPI_CLK_IFACE,
|
|
QSPI_NUM_CLKS
|
|
};
|
|
|
|
/*
|
|
* Number of entries in sgt returned from spi framework that-
|
|
* will be supported. Can be modified as required.
|
|
* In practice, given max_dma_len is 64KB, the number of
|
|
* entries is not expected to exceed 1.
|
|
*/
|
|
#define QSPI_MAX_SG 5
|
|
|
|
struct qcom_qspi {
|
|
void __iomem *base;
|
|
struct device *dev;
|
|
struct clk_bulk_data *clks;
|
|
struct qspi_xfer xfer;
|
|
struct dma_pool *dma_cmd_pool;
|
|
dma_addr_t dma_cmd_desc[QSPI_MAX_SG];
|
|
void *virt_cmd_desc[QSPI_MAX_SG];
|
|
unsigned int n_cmd_desc;
|
|
struct icc_path *icc_path_cpu_to_qspi;
|
|
unsigned long last_speed;
|
|
/* Lock to protect data accessed by IRQs */
|
|
spinlock_t lock;
|
|
};
|
|
|
|
static u32 qspi_buswidth_to_iomode(struct qcom_qspi *ctrl,
|
|
unsigned int buswidth)
|
|
{
|
|
switch (buswidth) {
|
|
case 1:
|
|
return SDR_1BIT;
|
|
case 2:
|
|
return SDR_2BIT;
|
|
case 4:
|
|
return SDR_4BIT;
|
|
default:
|
|
dev_warn_once(ctrl->dev,
|
|
"Unexpected bus width: %u\n", buswidth);
|
|
return SDR_1BIT;
|
|
}
|
|
}
|
|
|
|
static void qcom_qspi_pio_xfer_cfg(struct qcom_qspi *ctrl)
|
|
{
|
|
u32 pio_xfer_cfg;
|
|
u32 iomode;
|
|
const struct qspi_xfer *xfer;
|
|
|
|
xfer = &ctrl->xfer;
|
|
pio_xfer_cfg = readl(ctrl->base + PIO_XFER_CFG);
|
|
pio_xfer_cfg &= ~TRANSFER_DIRECTION;
|
|
pio_xfer_cfg |= xfer->dir;
|
|
if (xfer->is_last)
|
|
pio_xfer_cfg &= ~TRANSFER_FRAGMENT;
|
|
else
|
|
pio_xfer_cfg |= TRANSFER_FRAGMENT;
|
|
pio_xfer_cfg &= ~MULTI_IO_MODE_MSK;
|
|
iomode = qspi_buswidth_to_iomode(ctrl, xfer->buswidth);
|
|
pio_xfer_cfg |= iomode << MULTI_IO_MODE_SHFT;
|
|
|
|
writel(pio_xfer_cfg, ctrl->base + PIO_XFER_CFG);
|
|
}
|
|
|
|
static void qcom_qspi_pio_xfer_ctrl(struct qcom_qspi *ctrl)
|
|
{
|
|
u32 pio_xfer_ctrl;
|
|
|
|
pio_xfer_ctrl = readl(ctrl->base + PIO_XFER_CTRL);
|
|
pio_xfer_ctrl &= ~REQUEST_COUNT_MSK;
|
|
pio_xfer_ctrl |= ctrl->xfer.rem_bytes;
|
|
writel(pio_xfer_ctrl, ctrl->base + PIO_XFER_CTRL);
|
|
}
|
|
|
|
static void qcom_qspi_pio_xfer(struct qcom_qspi *ctrl)
|
|
{
|
|
u32 ints;
|
|
|
|
qcom_qspi_pio_xfer_cfg(ctrl);
|
|
|
|
/* Ack any previous interrupts that might be hanging around */
|
|
writel(QSPI_ALL_IRQS, ctrl->base + MSTR_INT_STATUS);
|
|
|
|
/* Setup new interrupts */
|
|
if (ctrl->xfer.dir == QSPI_WRITE)
|
|
ints = QSPI_ERR_IRQS | WR_FIFO_EMPTY;
|
|
else
|
|
ints = QSPI_ERR_IRQS | RESP_FIFO_RDY;
|
|
writel(ints, ctrl->base + MSTR_INT_EN);
|
|
|
|
/* Kick off the transfer */
|
|
qcom_qspi_pio_xfer_ctrl(ctrl);
|
|
}
|
|
|
|
static void qcom_qspi_handle_err(struct spi_master *master,
|
|
struct spi_message *msg)
|
|
{
|
|
u32 int_status;
|
|
struct qcom_qspi *ctrl = spi_master_get_devdata(master);
|
|
unsigned long flags;
|
|
int i;
|
|
|
|
spin_lock_irqsave(&ctrl->lock, flags);
|
|
writel(0, ctrl->base + MSTR_INT_EN);
|
|
int_status = readl(ctrl->base + MSTR_INT_STATUS);
|
|
writel(int_status, ctrl->base + MSTR_INT_STATUS);
|
|
ctrl->xfer.rem_bytes = 0;
|
|
|
|
/* free cmd descriptors if they are around (DMA mode) */
|
|
for (i = 0; i < ctrl->n_cmd_desc; i++)
|
|
dma_pool_free(ctrl->dma_cmd_pool, ctrl->virt_cmd_desc[i],
|
|
ctrl->dma_cmd_desc[i]);
|
|
ctrl->n_cmd_desc = 0;
|
|
spin_unlock_irqrestore(&ctrl->lock, flags);
|
|
}
|
|
|
|
static int qcom_qspi_set_speed(struct qcom_qspi *ctrl, unsigned long speed_hz)
|
|
{
|
|
int ret;
|
|
unsigned int avg_bw_cpu;
|
|
|
|
if (speed_hz == ctrl->last_speed)
|
|
return 0;
|
|
|
|
/* In regular operation (SBL_EN=1) core must be 4x transfer clock */
|
|
ret = dev_pm_opp_set_rate(ctrl->dev, speed_hz * 4);
|
|
if (ret) {
|
|
dev_err(ctrl->dev, "Failed to set core clk %d\n", ret);
|
|
return ret;
|
|
}
|
|
|
|
/*
|
|
* Set BW quota for CPU.
|
|
* We don't have explicit peak requirement so keep it equal to avg_bw.
|
|
*/
|
|
avg_bw_cpu = Bps_to_icc(speed_hz);
|
|
ret = icc_set_bw(ctrl->icc_path_cpu_to_qspi, avg_bw_cpu, avg_bw_cpu);
|
|
if (ret) {
|
|
dev_err(ctrl->dev, "%s: ICC BW voting failed for cpu: %d\n",
|
|
__func__, ret);
|
|
return ret;
|
|
}
|
|
|
|
ctrl->last_speed = speed_hz;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int qcom_qspi_alloc_desc(struct qcom_qspi *ctrl, dma_addr_t dma_ptr,
|
|
uint32_t n_bytes)
|
|
{
|
|
struct qspi_cmd_desc *virt_cmd_desc, *prev;
|
|
dma_addr_t dma_cmd_desc;
|
|
|
|
/* allocate for dma cmd descriptor */
|
|
virt_cmd_desc = dma_pool_alloc(ctrl->dma_cmd_pool, GFP_KERNEL | __GFP_ZERO, &dma_cmd_desc);
|
|
if (!virt_cmd_desc)
|
|
return -ENOMEM;
|
|
|
|
ctrl->virt_cmd_desc[ctrl->n_cmd_desc] = virt_cmd_desc;
|
|
ctrl->dma_cmd_desc[ctrl->n_cmd_desc] = dma_cmd_desc;
|
|
ctrl->n_cmd_desc++;
|
|
|
|
/* setup cmd descriptor */
|
|
virt_cmd_desc->data_address = dma_ptr;
|
|
virt_cmd_desc->direction = ctrl->xfer.dir;
|
|
virt_cmd_desc->multi_io_mode = qspi_buswidth_to_iomode(ctrl, ctrl->xfer.buswidth);
|
|
virt_cmd_desc->fragment = !ctrl->xfer.is_last;
|
|
virt_cmd_desc->length = n_bytes;
|
|
|
|
/* update previous descriptor */
|
|
if (ctrl->n_cmd_desc >= 2) {
|
|
prev = (ctrl->virt_cmd_desc)[ctrl->n_cmd_desc - 2];
|
|
prev->next_descriptor = dma_cmd_desc;
|
|
prev->fragment = 1;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int qcom_qspi_setup_dma_desc(struct qcom_qspi *ctrl,
|
|
struct spi_transfer *xfer)
|
|
{
|
|
int ret;
|
|
struct sg_table *sgt;
|
|
dma_addr_t dma_ptr_sg;
|
|
unsigned int dma_len_sg;
|
|
int i;
|
|
|
|
if (ctrl->n_cmd_desc) {
|
|
dev_err(ctrl->dev, "Remnant dma buffers n_cmd_desc-%d\n", ctrl->n_cmd_desc);
|
|
return -EIO;
|
|
}
|
|
|
|
sgt = (ctrl->xfer.dir == QSPI_READ) ? &xfer->rx_sg : &xfer->tx_sg;
|
|
if (!sgt->nents || sgt->nents > QSPI_MAX_SG) {
|
|
dev_warn_once(ctrl->dev, "Cannot handle %d entries in scatter list\n", sgt->nents);
|
|
return -EAGAIN;
|
|
}
|
|
|
|
for (i = 0; i < sgt->nents; i++) {
|
|
dma_ptr_sg = sg_dma_address(sgt->sgl + i);
|
|
if (!IS_ALIGNED(dma_ptr_sg, QSPI_ALIGN_REQ)) {
|
|
dev_warn_once(ctrl->dev, "dma_address not aligned to %d\n", QSPI_ALIGN_REQ);
|
|
return -EAGAIN;
|
|
}
|
|
}
|
|
|
|
for (i = 0; i < sgt->nents; i++) {
|
|
dma_ptr_sg = sg_dma_address(sgt->sgl + i);
|
|
dma_len_sg = sg_dma_len(sgt->sgl + i);
|
|
|
|
ret = qcom_qspi_alloc_desc(ctrl, dma_ptr_sg, dma_len_sg);
|
|
if (ret)
|
|
goto cleanup;
|
|
}
|
|
return 0;
|
|
|
|
cleanup:
|
|
for (i = 0; i < ctrl->n_cmd_desc; i++)
|
|
dma_pool_free(ctrl->dma_cmd_pool, ctrl->virt_cmd_desc[i],
|
|
ctrl->dma_cmd_desc[i]);
|
|
ctrl->n_cmd_desc = 0;
|
|
return ret;
|
|
}
|
|
|
|
static void qcom_qspi_dma_xfer(struct qcom_qspi *ctrl)
|
|
{
|
|
/* Setup new interrupts */
|
|
writel(DMA_CHAIN_DONE, ctrl->base + MSTR_INT_EN);
|
|
|
|
/* kick off transfer */
|
|
writel((u32)((ctrl->dma_cmd_desc)[0]), ctrl->base + NEXT_DMA_DESC_ADDR);
|
|
}
|
|
|
|
/* Switch to DMA if transfer length exceeds this */
|
|
#define QSPI_MAX_BYTES_FIFO 64
|
|
|
|
static bool qcom_qspi_can_dma(struct spi_controller *ctlr,
|
|
struct spi_device *slv, struct spi_transfer *xfer)
|
|
{
|
|
return xfer->len > QSPI_MAX_BYTES_FIFO;
|
|
}
|
|
|
|
static int qcom_qspi_transfer_one(struct spi_master *master,
|
|
struct spi_device *slv,
|
|
struct spi_transfer *xfer)
|
|
{
|
|
struct qcom_qspi *ctrl = spi_master_get_devdata(master);
|
|
int ret;
|
|
unsigned long speed_hz;
|
|
unsigned long flags;
|
|
u32 mstr_cfg;
|
|
|
|
speed_hz = slv->max_speed_hz;
|
|
if (xfer->speed_hz)
|
|
speed_hz = xfer->speed_hz;
|
|
|
|
ret = qcom_qspi_set_speed(ctrl, speed_hz);
|
|
if (ret)
|
|
return ret;
|
|
|
|
spin_lock_irqsave(&ctrl->lock, flags);
|
|
mstr_cfg = readl(ctrl->base + MSTR_CONFIG);
|
|
|
|
/* We are half duplex, so either rx or tx will be set */
|
|
if (xfer->rx_buf) {
|
|
ctrl->xfer.dir = QSPI_READ;
|
|
ctrl->xfer.buswidth = xfer->rx_nbits;
|
|
ctrl->xfer.rx_buf = xfer->rx_buf;
|
|
} else {
|
|
ctrl->xfer.dir = QSPI_WRITE;
|
|
ctrl->xfer.buswidth = xfer->tx_nbits;
|
|
ctrl->xfer.tx_buf = xfer->tx_buf;
|
|
}
|
|
ctrl->xfer.is_last = list_is_last(&xfer->transfer_list,
|
|
&master->cur_msg->transfers);
|
|
ctrl->xfer.rem_bytes = xfer->len;
|
|
|
|
if (xfer->rx_sg.nents || xfer->tx_sg.nents) {
|
|
/* do DMA transfer */
|
|
if (!(mstr_cfg & DMA_ENABLE)) {
|
|
mstr_cfg |= DMA_ENABLE;
|
|
writel(mstr_cfg, ctrl->base + MSTR_CONFIG);
|
|
}
|
|
|
|
ret = qcom_qspi_setup_dma_desc(ctrl, xfer);
|
|
if (ret != -EAGAIN) {
|
|
if (!ret)
|
|
qcom_qspi_dma_xfer(ctrl);
|
|
goto exit;
|
|
}
|
|
dev_warn_once(ctrl->dev, "DMA failure, falling back to PIO\n");
|
|
ret = 0; /* We'll retry w/ PIO */
|
|
}
|
|
|
|
if (mstr_cfg & DMA_ENABLE) {
|
|
mstr_cfg &= ~DMA_ENABLE;
|
|
writel(mstr_cfg, ctrl->base + MSTR_CONFIG);
|
|
}
|
|
qcom_qspi_pio_xfer(ctrl);
|
|
|
|
exit:
|
|
spin_unlock_irqrestore(&ctrl->lock, flags);
|
|
|
|
if (ret)
|
|
return ret;
|
|
|
|
/* We'll call spi_finalize_current_transfer() when done */
|
|
return 1;
|
|
}
|
|
|
|
static int qcom_qspi_prepare_message(struct spi_master *master,
|
|
struct spi_message *message)
|
|
{
|
|
u32 mstr_cfg;
|
|
struct qcom_qspi *ctrl;
|
|
int tx_data_oe_delay = 1;
|
|
int tx_data_delay = 1;
|
|
unsigned long flags;
|
|
|
|
ctrl = spi_master_get_devdata(master);
|
|
spin_lock_irqsave(&ctrl->lock, flags);
|
|
|
|
mstr_cfg = readl(ctrl->base + MSTR_CONFIG);
|
|
mstr_cfg &= ~CHIP_SELECT_NUM;
|
|
if (spi_get_chipselect(message->spi, 0))
|
|
mstr_cfg |= CHIP_SELECT_NUM;
|
|
|
|
mstr_cfg |= FB_CLK_EN | PIN_WPN | PIN_HOLDN | SBL_EN | FULL_CYCLE_MODE;
|
|
mstr_cfg &= ~(SPI_MODE_MSK | TX_DATA_OE_DELAY_MSK | TX_DATA_DELAY_MSK);
|
|
mstr_cfg |= message->spi->mode << SPI_MODE_SHFT;
|
|
mstr_cfg |= tx_data_oe_delay << TX_DATA_OE_DELAY_SHFT;
|
|
mstr_cfg |= tx_data_delay << TX_DATA_DELAY_SHFT;
|
|
mstr_cfg &= ~DMA_ENABLE;
|
|
|
|
writel(mstr_cfg, ctrl->base + MSTR_CONFIG);
|
|
spin_unlock_irqrestore(&ctrl->lock, flags);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int qcom_qspi_alloc_dma(struct qcom_qspi *ctrl)
|
|
{
|
|
ctrl->dma_cmd_pool = dmam_pool_create("qspi cmd desc pool",
|
|
ctrl->dev, sizeof(struct qspi_cmd_desc), 0, 0);
|
|
if (!ctrl->dma_cmd_pool)
|
|
return -ENOMEM;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static irqreturn_t pio_read(struct qcom_qspi *ctrl)
|
|
{
|
|
u32 rd_fifo_status;
|
|
u32 rd_fifo;
|
|
unsigned int wr_cnts;
|
|
unsigned int bytes_to_read;
|
|
unsigned int words_to_read;
|
|
u32 *word_buf;
|
|
u8 *byte_buf;
|
|
int i;
|
|
|
|
rd_fifo_status = readl(ctrl->base + RD_FIFO_STATUS);
|
|
|
|
if (!(rd_fifo_status & FIFO_RDY)) {
|
|
dev_dbg(ctrl->dev, "Spurious IRQ %#x\n", rd_fifo_status);
|
|
return IRQ_NONE;
|
|
}
|
|
|
|
wr_cnts = (rd_fifo_status & WR_CNTS_MSK) >> WR_CNTS_SHFT;
|
|
wr_cnts = min(wr_cnts, ctrl->xfer.rem_bytes);
|
|
|
|
words_to_read = wr_cnts / QSPI_BYTES_PER_WORD;
|
|
bytes_to_read = wr_cnts % QSPI_BYTES_PER_WORD;
|
|
|
|
if (words_to_read) {
|
|
word_buf = ctrl->xfer.rx_buf;
|
|
ctrl->xfer.rem_bytes -= words_to_read * QSPI_BYTES_PER_WORD;
|
|
ioread32_rep(ctrl->base + RD_FIFO, word_buf, words_to_read);
|
|
ctrl->xfer.rx_buf = word_buf + words_to_read;
|
|
}
|
|
|
|
if (bytes_to_read) {
|
|
byte_buf = ctrl->xfer.rx_buf;
|
|
rd_fifo = readl(ctrl->base + RD_FIFO);
|
|
ctrl->xfer.rem_bytes -= bytes_to_read;
|
|
for (i = 0; i < bytes_to_read; i++)
|
|
*byte_buf++ = rd_fifo >> (i * BITS_PER_BYTE);
|
|
ctrl->xfer.rx_buf = byte_buf;
|
|
}
|
|
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
static irqreturn_t pio_write(struct qcom_qspi *ctrl)
|
|
{
|
|
const void *xfer_buf = ctrl->xfer.tx_buf;
|
|
const int *word_buf;
|
|
const char *byte_buf;
|
|
unsigned int wr_fifo_bytes;
|
|
unsigned int wr_fifo_words;
|
|
unsigned int wr_size;
|
|
unsigned int rem_words;
|
|
|
|
wr_fifo_bytes = readl(ctrl->base + PIO_XFER_STATUS);
|
|
wr_fifo_bytes >>= WR_FIFO_BYTES_SHFT;
|
|
|
|
if (ctrl->xfer.rem_bytes < QSPI_BYTES_PER_WORD) {
|
|
/* Process the last 1-3 bytes */
|
|
wr_size = min(wr_fifo_bytes, ctrl->xfer.rem_bytes);
|
|
ctrl->xfer.rem_bytes -= wr_size;
|
|
|
|
byte_buf = xfer_buf;
|
|
while (wr_size--)
|
|
writel(*byte_buf++,
|
|
ctrl->base + PIO_DATAOUT_1B);
|
|
ctrl->xfer.tx_buf = byte_buf;
|
|
} else {
|
|
/*
|
|
* Process all the whole words; to keep things simple we'll
|
|
* just wait for the next interrupt to handle the last 1-3
|
|
* bytes if we don't have an even number of words.
|
|
*/
|
|
rem_words = ctrl->xfer.rem_bytes / QSPI_BYTES_PER_WORD;
|
|
wr_fifo_words = wr_fifo_bytes / QSPI_BYTES_PER_WORD;
|
|
|
|
wr_size = min(rem_words, wr_fifo_words);
|
|
ctrl->xfer.rem_bytes -= wr_size * QSPI_BYTES_PER_WORD;
|
|
|
|
word_buf = xfer_buf;
|
|
iowrite32_rep(ctrl->base + PIO_DATAOUT_4B, word_buf, wr_size);
|
|
ctrl->xfer.tx_buf = word_buf + wr_size;
|
|
|
|
}
|
|
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
static irqreturn_t qcom_qspi_irq(int irq, void *dev_id)
|
|
{
|
|
u32 int_status;
|
|
struct qcom_qspi *ctrl = dev_id;
|
|
irqreturn_t ret = IRQ_NONE;
|
|
|
|
spin_lock(&ctrl->lock);
|
|
|
|
int_status = readl(ctrl->base + MSTR_INT_STATUS);
|
|
writel(int_status, ctrl->base + MSTR_INT_STATUS);
|
|
|
|
/* PIO mode handling */
|
|
if (ctrl->xfer.dir == QSPI_WRITE) {
|
|
if (int_status & WR_FIFO_EMPTY)
|
|
ret = pio_write(ctrl);
|
|
} else {
|
|
if (int_status & RESP_FIFO_RDY)
|
|
ret = pio_read(ctrl);
|
|
}
|
|
|
|
if (int_status & QSPI_ERR_IRQS) {
|
|
if (int_status & RESP_FIFO_UNDERRUN)
|
|
dev_err(ctrl->dev, "IRQ error: FIFO underrun\n");
|
|
if (int_status & WR_FIFO_OVERRUN)
|
|
dev_err(ctrl->dev, "IRQ error: FIFO overrun\n");
|
|
if (int_status & HRESP_FROM_NOC_ERR)
|
|
dev_err(ctrl->dev, "IRQ error: NOC response error\n");
|
|
ret = IRQ_HANDLED;
|
|
}
|
|
|
|
if (!ctrl->xfer.rem_bytes) {
|
|
writel(0, ctrl->base + MSTR_INT_EN);
|
|
spi_finalize_current_transfer(dev_get_drvdata(ctrl->dev));
|
|
}
|
|
|
|
/* DMA mode handling */
|
|
if (int_status & DMA_CHAIN_DONE) {
|
|
int i;
|
|
|
|
writel(0, ctrl->base + MSTR_INT_EN);
|
|
ctrl->xfer.rem_bytes = 0;
|
|
|
|
for (i = 0; i < ctrl->n_cmd_desc; i++)
|
|
dma_pool_free(ctrl->dma_cmd_pool, ctrl->virt_cmd_desc[i],
|
|
ctrl->dma_cmd_desc[i]);
|
|
ctrl->n_cmd_desc = 0;
|
|
|
|
ret = IRQ_HANDLED;
|
|
spi_finalize_current_transfer(dev_get_drvdata(ctrl->dev));
|
|
}
|
|
|
|
spin_unlock(&ctrl->lock);
|
|
return ret;
|
|
}
|
|
|
|
static int qcom_qspi_probe(struct platform_device *pdev)
|
|
{
|
|
int ret;
|
|
struct device *dev;
|
|
struct spi_master *master;
|
|
struct qcom_qspi *ctrl;
|
|
|
|
dev = &pdev->dev;
|
|
|
|
master = devm_spi_alloc_master(dev, sizeof(*ctrl));
|
|
if (!master)
|
|
return -ENOMEM;
|
|
|
|
platform_set_drvdata(pdev, master);
|
|
|
|
ctrl = spi_master_get_devdata(master);
|
|
|
|
spin_lock_init(&ctrl->lock);
|
|
ctrl->dev = dev;
|
|
ctrl->base = devm_platform_ioremap_resource(pdev, 0);
|
|
if (IS_ERR(ctrl->base))
|
|
return PTR_ERR(ctrl->base);
|
|
|
|
ctrl->clks = devm_kcalloc(dev, QSPI_NUM_CLKS,
|
|
sizeof(*ctrl->clks), GFP_KERNEL);
|
|
if (!ctrl->clks)
|
|
return -ENOMEM;
|
|
|
|
ctrl->clks[QSPI_CLK_CORE].id = "core";
|
|
ctrl->clks[QSPI_CLK_IFACE].id = "iface";
|
|
ret = devm_clk_bulk_get(dev, QSPI_NUM_CLKS, ctrl->clks);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ctrl->icc_path_cpu_to_qspi = devm_of_icc_get(dev, "qspi-config");
|
|
if (IS_ERR(ctrl->icc_path_cpu_to_qspi))
|
|
return dev_err_probe(dev, PTR_ERR(ctrl->icc_path_cpu_to_qspi),
|
|
"Failed to get cpu path\n");
|
|
|
|
/* Set BW vote for register access */
|
|
ret = icc_set_bw(ctrl->icc_path_cpu_to_qspi, Bps_to_icc(1000),
|
|
Bps_to_icc(1000));
|
|
if (ret) {
|
|
dev_err(ctrl->dev, "%s: ICC BW voting failed for cpu: %d\n",
|
|
__func__, ret);
|
|
return ret;
|
|
}
|
|
|
|
ret = icc_disable(ctrl->icc_path_cpu_to_qspi);
|
|
if (ret) {
|
|
dev_err(ctrl->dev, "%s: ICC disable failed for cpu: %d\n",
|
|
__func__, ret);
|
|
return ret;
|
|
}
|
|
|
|
ret = platform_get_irq(pdev, 0);
|
|
if (ret < 0)
|
|
return ret;
|
|
ret = devm_request_irq(dev, ret, qcom_qspi_irq, 0, dev_name(dev), ctrl);
|
|
if (ret) {
|
|
dev_err(dev, "Failed to request irq %d\n", ret);
|
|
return ret;
|
|
}
|
|
|
|
ret = dma_set_mask_and_coherent(dev, DMA_BIT_MASK(32));
|
|
if (ret)
|
|
return dev_err_probe(dev, ret, "could not set DMA mask\n");
|
|
|
|
master->max_speed_hz = 300000000;
|
|
master->max_dma_len = 65536; /* as per HPG */
|
|
master->dma_alignment = QSPI_ALIGN_REQ;
|
|
master->num_chipselect = QSPI_NUM_CS;
|
|
master->bus_num = -1;
|
|
master->dev.of_node = pdev->dev.of_node;
|
|
master->mode_bits = SPI_MODE_0 |
|
|
SPI_TX_DUAL | SPI_RX_DUAL |
|
|
SPI_TX_QUAD | SPI_RX_QUAD;
|
|
master->flags = SPI_CONTROLLER_HALF_DUPLEX;
|
|
master->prepare_message = qcom_qspi_prepare_message;
|
|
master->transfer_one = qcom_qspi_transfer_one;
|
|
master->handle_err = qcom_qspi_handle_err;
|
|
if (of_property_read_bool(pdev->dev.of_node, "iommus"))
|
|
master->can_dma = qcom_qspi_can_dma;
|
|
master->auto_runtime_pm = true;
|
|
|
|
ret = devm_pm_opp_set_clkname(&pdev->dev, "core");
|
|
if (ret)
|
|
return ret;
|
|
/* OPP table is optional */
|
|
ret = devm_pm_opp_of_add_table(&pdev->dev);
|
|
if (ret && ret != -ENODEV) {
|
|
dev_err(&pdev->dev, "invalid OPP table in device tree\n");
|
|
return ret;
|
|
}
|
|
|
|
ret = qcom_qspi_alloc_dma(ctrl);
|
|
if (ret)
|
|
return ret;
|
|
|
|
pm_runtime_use_autosuspend(dev);
|
|
pm_runtime_set_autosuspend_delay(dev, 250);
|
|
pm_runtime_enable(dev);
|
|
|
|
ret = spi_register_master(master);
|
|
if (!ret)
|
|
return 0;
|
|
|
|
pm_runtime_disable(dev);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static void qcom_qspi_remove(struct platform_device *pdev)
|
|
{
|
|
struct spi_master *master = platform_get_drvdata(pdev);
|
|
|
|
/* Unregister _before_ disabling pm_runtime() so we stop transfers */
|
|
spi_unregister_master(master);
|
|
|
|
pm_runtime_disable(&pdev->dev);
|
|
}
|
|
|
|
static int __maybe_unused qcom_qspi_runtime_suspend(struct device *dev)
|
|
{
|
|
struct spi_master *master = dev_get_drvdata(dev);
|
|
struct qcom_qspi *ctrl = spi_master_get_devdata(master);
|
|
int ret;
|
|
|
|
/* Drop the performance state vote */
|
|
dev_pm_opp_set_rate(dev, 0);
|
|
clk_bulk_disable_unprepare(QSPI_NUM_CLKS, ctrl->clks);
|
|
|
|
ret = icc_disable(ctrl->icc_path_cpu_to_qspi);
|
|
if (ret) {
|
|
dev_err_ratelimited(ctrl->dev, "%s: ICC disable failed for cpu: %d\n",
|
|
__func__, ret);
|
|
return ret;
|
|
}
|
|
|
|
pinctrl_pm_select_sleep_state(dev);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int __maybe_unused qcom_qspi_runtime_resume(struct device *dev)
|
|
{
|
|
struct spi_master *master = dev_get_drvdata(dev);
|
|
struct qcom_qspi *ctrl = spi_master_get_devdata(master);
|
|
int ret;
|
|
|
|
pinctrl_pm_select_default_state(dev);
|
|
|
|
ret = icc_enable(ctrl->icc_path_cpu_to_qspi);
|
|
if (ret) {
|
|
dev_err_ratelimited(ctrl->dev, "%s: ICC enable failed for cpu: %d\n",
|
|
__func__, ret);
|
|
return ret;
|
|
}
|
|
|
|
ret = clk_bulk_prepare_enable(QSPI_NUM_CLKS, ctrl->clks);
|
|
if (ret)
|
|
return ret;
|
|
|
|
return dev_pm_opp_set_rate(dev, ctrl->last_speed * 4);
|
|
}
|
|
|
|
static int __maybe_unused qcom_qspi_suspend(struct device *dev)
|
|
{
|
|
struct spi_master *master = dev_get_drvdata(dev);
|
|
int ret;
|
|
|
|
ret = spi_master_suspend(master);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = pm_runtime_force_suspend(dev);
|
|
if (ret)
|
|
spi_master_resume(master);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int __maybe_unused qcom_qspi_resume(struct device *dev)
|
|
{
|
|
struct spi_master *master = dev_get_drvdata(dev);
|
|
int ret;
|
|
|
|
ret = pm_runtime_force_resume(dev);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = spi_master_resume(master);
|
|
if (ret)
|
|
pm_runtime_force_suspend(dev);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static const struct dev_pm_ops qcom_qspi_dev_pm_ops = {
|
|
SET_RUNTIME_PM_OPS(qcom_qspi_runtime_suspend,
|
|
qcom_qspi_runtime_resume, NULL)
|
|
SET_SYSTEM_SLEEP_PM_OPS(qcom_qspi_suspend, qcom_qspi_resume)
|
|
};
|
|
|
|
static const struct of_device_id qcom_qspi_dt_match[] = {
|
|
{ .compatible = "qcom,qspi-v1", },
|
|
{ }
|
|
};
|
|
MODULE_DEVICE_TABLE(of, qcom_qspi_dt_match);
|
|
|
|
static struct platform_driver qcom_qspi_driver = {
|
|
.driver = {
|
|
.name = "qcom_qspi",
|
|
.pm = &qcom_qspi_dev_pm_ops,
|
|
.of_match_table = qcom_qspi_dt_match,
|
|
},
|
|
.probe = qcom_qspi_probe,
|
|
.remove_new = qcom_qspi_remove,
|
|
};
|
|
module_platform_driver(qcom_qspi_driver);
|
|
|
|
MODULE_DESCRIPTION("SPI driver for QSPI cores");
|
|
MODULE_LICENSE("GPL v2");
|