On Raspberry Pis without onboard USB hub frequent device reconnects
can trigger a interrupt storm after DWC2 entered host clock gating.
This is caused by a race between _dwc2_hcd_suspend() and the port
interrupt, which sets port_connect_status. The issue occurs if
port_connect_status is still 1, but there is no connection anymore:
usb 1-1: USB disconnect, device number 25
dwc2 3f980000.usb: _dwc2_hcd_suspend: port_connect_status: 1
dwc2 3f980000.usb: Entering host clock gating.
Disabling IRQ #66
irq 66: nobody cared (try booting with the "irqpoll" option)
CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.12.0-gc1bb81b13202-dirty #322
Hardware name: BCM2835
Call trace:
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x50/0x64
dump_stack_lvl from __report_bad_irq+0x38/0xc0
__report_bad_irq from note_interrupt+0x2ac/0x2f4
note_interrupt from handle_irq_event+0x88/0x8c
handle_irq_event from handle_level_irq+0xb4/0x1ac
handle_level_irq from generic_handle_domain_irq+0x24/0x34
generic_handle_domain_irq from bcm2836_chained_handle_irq+0x24/0x28
bcm2836_chained_handle_irq from generic_handle_domain_irq+0x24/0x34
generic_handle_domain_irq from generic_handle_arch_irq+0x34/0x44
generic_handle_arch_irq from __irq_svc+0x88/0xb0
Exception stack(0xc1d01f20 to 0xc1d01f68)
1f20: 0004ef3c 00000001 00000000 00000000 c1d09780 c1f6bb5c c1d04e54 c1c60ca8
1f40: c1d04e94 00000000 00000000 c1d092a8 c1f6af20 c1d01f70 c1211b98 c1212f40
1f60: 60000013 ffffffff
__irq_svc from default_idle_call+0x1c/0xb0
default_idle_call from do_idle+0x21c/0x284
do_idle from cpu_startup_entry+0x28/0x2c
cpu_startup_entry from kernel_init+0x0/0x12c
handlers:
[<e3a25c00>] dwc2_handle_common_intr
[<58bf98a3>] usb_hcd_irq
Disabling IRQ #66
So avoid this by reading the connection status directly.
Fixes: 113f86d0c3 ("usb: dwc2: Update partial power down entering by system suspend")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20241202001631.75473-4-wahrenst@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Rasperry Pis without onboard USB hub the power cycle during
power connect init only disable the port but never enabled it again:
usb usb1-port1: attempt power cycle
The port relevant part in dwc2_hcd_hub_control() is skipped in case
port_connect_status = 0 under the assumption the core is or will be soon
in device mode. But this assumption is wrong, because after ClearPortFeature
USB_PORT_FEAT_POWER the port_connect_status will also be 0 and
SetPortFeature (incl. USB_PORT_FEAT_POWER) will be a no-op.
Fix the behavior of dwc2_hcd_hub_control() by replacing the
port_connect_status check with dwc2_is_device_mode().
Link: https://github.com/raspberrypi/linux/issues/6247
Fixes: 7359d482eb ("staging: HCD files for the DWC2 driver")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20241202001631.75473-3-wahrenst@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Raspberry Pi can suffer on interrupt storms on HCD resume. The dwc2
driver sometimes misses to enable HCD_FLAG_HW_ACCESSIBLE before re-enabling
the interrupts. This causes a situation where both handler ignore a incoming
port interrupt and force the upper layers to disable the dwc2 interrupt
line. This leaves the USB interface in a unusable state:
irq 66: nobody cared (try booting with the "irqpoll" option)
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 6.10.0-rc3
Hardware name: BCM2835
Call trace:
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x50/0x64
dump_stack_lvl from __report_bad_irq+0x38/0xc0
__report_bad_irq from note_interrupt+0x2ac/0x2f4
note_interrupt from handle_irq_event+0x88/0x8c
handle_irq_event from handle_level_irq+0xb4/0x1ac
handle_level_irq from generic_handle_domain_irq+0x24/0x34
generic_handle_domain_irq from bcm2836_chained_handle_irq+0x24/0x28
bcm2836_chained_handle_irq from generic_handle_domain_irq+0x24/0x34
generic_handle_domain_irq from generic_handle_arch_irq+0x34/0x44
generic_handle_arch_irq from __irq_svc+0x88/0xb0
Exception stack(0xc1b01f20 to 0xc1b01f68)
1f20: 0005c0d4 00000001 00000000 00000000 c1b09780 c1d6b32c c1b04e54 c1a5eae8
1f40: c1b04e90 00000000 00000000 00000000 c1d6a8a0 c1b01f70 c11d2da8 c11d4160
1f60: 60000013 ffffffff
__irq_svc from default_idle_call+0x1c/0xb0
default_idle_call from do_idle+0x21c/0x284
do_idle from cpu_startup_entry+0x28/0x2c
cpu_startup_entry from kernel_init+0x0/0x12c
handlers:
[<f539e0f4>] dwc2_handle_common_intr
[<75cd278b>] usb_hcd_irq
Disabling IRQ #66
So enable the HCD_FLAG_HW_ACCESSIBLE flag in case there is a port
connection.
Fixes: c74c26f6e3 ("usb: dwc2: Fix partial power down exiting by system resume")
Closes: https://lore.kernel.org/linux-usb/3fd0c2fb-4752-45b3-94eb-42352703e1fd@gmx.net/T/
Link: https://lore.kernel.org/all/5e8cbce0-3260-2971-484f-fc73a3b2bd28@synopsys.com/
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20241202001631.75473-2-wahrenst@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Add generic support for built-in boot DTB files
- Enable TAB cycling for dialog buttons in nconfig
- Fix issues in streamline_config.pl
- Refactor Kconfig
- Add support for Clang's AutoFDO (Automatic Feedback-Directed
Optimization)
- Add support for Clang's Propeller, a profile-guided optimization.
- Change the working directory to the external module directory for M=
builds
- Support building external modules in a separate output directory
- Enable objtool for *.mod.o and additional kernel objects
- Use lz4 instead of deprecated lz4c
- Work around a performance issue with "git describe"
- Refactor modpost
-----BEGIN PGP SIGNATURE-----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=GDKD
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- Add generic support for built-in boot DTB files
- Enable TAB cycling for dialog buttons in nconfig
- Fix issues in streamline_config.pl
- Refactor Kconfig
- Add support for Clang's AutoFDO (Automatic Feedback-Directed
Optimization)
- Add support for Clang's Propeller, a profile-guided optimization.
- Change the working directory to the external module directory for M=
builds
- Support building external modules in a separate output directory
- Enable objtool for *.mod.o and additional kernel objects
- Use lz4 instead of deprecated lz4c
- Work around a performance issue with "git describe"
- Refactor modpost
* tag 'kbuild-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (85 commits)
kbuild: rename .tmp_vmlinux.kallsyms0.syms to .tmp_vmlinux0.syms
gitignore: Don't ignore 'tags' directory
kbuild: add dependency from vmlinux to resolve_btfids
modpost: replace tdb_hash() with hash_str()
kbuild: deb-pkg: add python3:native to build dependency
genksyms: reduce indentation in export_symbol()
modpost: improve error messages in device_id_check()
modpost: rename alias symbol for MODULE_DEVICE_TABLE()
modpost: rename variables in handle_moddevtable()
modpost: move strstarts() to modpost.h
modpost: convert do_usb_table() to a generic handler
modpost: convert do_of_table() to a generic handler
modpost: convert do_pnp_device_entry() to a generic handler
modpost: convert do_pnp_card_entries() to a generic handler
modpost: call module_alias_printf() from all do_*_entry() functions
modpost: pass (struct module *) to do_*_entry() functions
modpost: remove DEF_FIELD_ADDR_VAR() macro
modpost: deduplicate MODULE_ALIAS() for all drivers
modpost: introduce module_alias_printf() helper
modpost: remove unnecessary check in do_acpi_entry()
...
We need the USB fixes in here as well, and this resolves a merge
conflict in:
drivers/usb/typec/tcpm/tcpm.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/20241101150730.090dc30f@canb.auug.org.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit fde192511b ("kconfig: remove tristate choice support"),
all choice blocks are now boolean. There is no longer a need to specify
the choice type explicitly.
Most choice blocks already use "prompt". Before the next commit removes
support for the "bool" syntax in choice entries, this commit converts
the remaining "bool" occurences under drivers/usb/.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
The commit d483f034f0 ("usb: dwc2: Skip clock gating on Broadcom SoCs")
introduced a regression on Raspberry Pi 3 B Plus, which prevents
enumeration of the onboard Microchip LAN7800 in case no external USB device
is connected during boot.
Fixes: d483f034f0 ("usb: dwc2: Skip clock gating on Broadcom SoCs")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20241025103621.4780-2-wahrenst@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/usb to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20240924084329.53094-2-u.kleine-koenig@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dwc2_handle_usb_suspend_intr() function disables gadget clocks in USB
peripheral mode when no other power-down mode is available (introduced by
commit 0112b7ce68 ("usb: dwc2: Update dwc2_handle_usb_suspend_intr function.")).
However, the dwc2_drd_role_sw_set() USB role update handler attempts to
read DWC2 registers if the USB role has changed while the USB is in suspend
mode (when the clocks are gated). This causes the system to hang.
Release the gadget clocks before handling the USB role update.
Fixes: 0112b7ce68 ("usb: dwc2: Update dwc2_handle_usb_suspend_intr function.")
Cc: stable@vger.kernel.org
Signed-off-by: Tomas Marek <tomas.marek@elrest.cz>
Link: https://lore.kernel.org/r/20240906055025.25057-1-tomas.marek@elrest.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The issue is that before entering the crash kernel, the DWC USB controller
did not perform operations such as resetting the interrupt mask bits.
After entering the crash kernel,before the USB interrupt handler
registration was completed while loading the DWC USB driver,an GINTSTS_SOF
interrupt was received.This triggered the misroute_irq process within the
GIC handling framework,ultimately leading to the misrouting of the
interrupt,causing it to be handled by the wrong interrupt handler
and resulting in the issue.
Summary:In a scenario where the kernel triggers a panic and enters
the crash kernel,it is necessary to ensure that the interrupt mask
bit is not enabled before the interrupt registration is complete.
If an interrupt reaches the CPU at this moment,it will certainly
not be handled correctly,especially in cases where this interrupt
is reported frequently.
Please refer to the Crashkernel dmesg information as follows
(the message on line 3 was added before devm_request_irq is
called by the dwc2_driver_probe function):
[ 5.866837][ T1] dwc2 JMIC0010:01: supply vusb_d not found, using dummy regulator
[ 5.874588][ T1] dwc2 JMIC0010:01: supply vusb_a not found, using dummy regulator
[ 5.882335][ T1] dwc2 JMIC0010:01: before devm_request_irq irq: [71], gintmsk[0xf300080e], gintsts[0x04200009]
[ 5.892686][ C0] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.10.0-jmnd1.2_RC #18
[ 5.900327][ C0] Hardware name: CMSS HyperCard4-25G/HyperCard4-25G, BIOS 1.6.4 Jul 8 2024
[ 5.908836][ C0] Call trace:
[ 5.911965][ C0] dump_backtrace+0x0/0x1f0
[ 5.916308][ C0] show_stack+0x20/0x30
[ 5.920304][ C0] dump_stack+0xd8/0x140
[ 5.924387][ C0] pcie_xxx_handler+0x3c/0x1d8
[ 5.930121][ C0] __handle_irq_event_percpu+0x64/0x1e0
[ 5.935506][ C0] handle_irq_event+0x80/0x1d0
[ 5.940109][ C0] try_one_irq+0x138/0x174
[ 5.944365][ C0] misrouted_irq+0x134/0x140
[ 5.948795][ C0] note_interrupt+0x1d0/0x30c
[ 5.953311][ C0] handle_irq_event+0x13c/0x1d0
[ 5.958001][ C0] handle_fasteoi_irq+0xd4/0x260
[ 5.962779][ C0] __handle_domain_irq+0x88/0xf0
[ 5.967555][ C0] gic_handle_irq+0x9c/0x2f0
[ 5.971985][ C0] el1_irq+0xb8/0x140
[ 5.975807][ C0] __setup_irq+0x3dc/0x7cc
[ 5.980064][ C0] request_threaded_irq+0xf4/0x1b4
[ 5.985015][ C0] devm_request_threaded_irq+0x80/0x100
[ 5.990400][ C0] dwc2_driver_probe+0x1b8/0x6b0
[ 5.995178][ C0] platform_drv_probe+0x5c/0xb0
[ 5.999868][ C0] really_probe+0xf8/0x51c
[ 6.004125][ C0] driver_probe_device+0xfc/0x170
[ 6.008989][ C0] device_driver_attach+0xc8/0xd0
[ 6.013853][ C0] __driver_attach+0xe8/0x1b0
[ 6.018369][ C0] bus_for_each_dev+0x7c/0xdc
[ 6.022886][ C0] driver_attach+0x2c/0x3c
[ 6.027143][ C0] bus_add_driver+0xdc/0x240
[ 6.031573][ C0] driver_register+0x80/0x13c
[ 6.036090][ C0] __platform_driver_register+0x50/0x5c
[ 6.041476][ C0] dwc2_platform_driver_init+0x24/0x30
[ 6.046774][ C0] do_one_initcall+0x50/0x25c
[ 6.051291][ C0] do_initcall_level+0xe4/0xfc
[ 6.055894][ C0] do_initcalls+0x80/0xa4
[ 6.060064][ C0] kernel_init_freeable+0x198/0x240
[ 6.065102][ C0] kernel_init+0x1c/0x12c
Signed-off-by: Shawn Shao <shawn.shao@jaguarmicro.com>
Link: https://lore.kernel.org/r/20240830031709.134-1-shawn.shao@jaguarmicro.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On resume of the Raspberry Pi the dwc2 driver fails to enable
HCD_FLAG_HW_ACCESSIBLE before re-enabling the interrupts.
This causes a situation where both handler ignore a incoming port
interrupt and force the upper layers to disable the dwc2 interrupt line.
This leaves the USB interface in a unusable state:
irq 66: nobody cared (try booting with the "irqpoll" option)
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 6.10.0-rc3
Hardware name: BCM2835
Call trace:
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x50/0x64
dump_stack_lvl from __report_bad_irq+0x38/0xc0
__report_bad_irq from note_interrupt+0x2ac/0x2f4
note_interrupt from handle_irq_event+0x88/0x8c
handle_irq_event from handle_level_irq+0xb4/0x1ac
handle_level_irq from generic_handle_domain_irq+0x24/0x34
generic_handle_domain_irq from bcm2836_chained_handle_irq+0x24/0x28
bcm2836_chained_handle_irq from generic_handle_domain_irq+0x24/0x34
generic_handle_domain_irq from generic_handle_arch_irq+0x34/0x44
generic_handle_arch_irq from __irq_svc+0x88/0xb0
Exception stack(0xc1b01f20 to 0xc1b01f68)
1f20: 0005c0d4 00000001 00000000 00000000 c1b09780 c1d6b32c c1b04e54 c1a5eae8
1f40: c1b04e90 00000000 00000000 00000000 c1d6a8a0 c1b01f70 c11d2da8 c11d4160
1f60: 60000013 ffffffff
__irq_svc from default_idle_call+0x1c/0xb0
default_idle_call from do_idle+0x21c/0x284
do_idle from cpu_startup_entry+0x28/0x2c
cpu_startup_entry from kernel_init+0x0/0x12c
handlers:
[<f539e0f4>] dwc2_handle_common_intr
[<75cd278b>] usb_hcd_irq
Disabling IRQ #66
Disabling clock gating workaround this issue.
Fixes: 0112b7ce68 ("usb: dwc2: Update dwc2_handle_usb_suspend_intr function.")
Link: https://lore.kernel.org/linux-usb/3fd0c2fb-4752-45b3-94eb-42352703e1fd@gmx.net/T/
Link: https://lore.kernel.org/all/5e8cbce0-3260-2971-484f-fc73a3b2bd28@synopsys.com/
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Link: https://lore.kernel.org/r/20240728130029.78279-5-wahrenst@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit c4a0f7a6ab ("usb: dwc2: Skip clock gating on Samsung
SoCs") introduced a parameter to skip enabling clock gating mode
even the hardware platform should supports it.
In order to make this more visible also print this in show
parameters of debugfs.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240728130029.78279-3-wahrenst@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The size of the internal RAM of the DesignWare USB controller changed
between the different Lantiq SoCs. We have the following sizes:
Amazon + Danube: 8 KByte
Amazon SE + arx100: 2 KByte
xrx200 + xrx300: 2.5 KByte
For Danube SoC we do not provide the params and let the driver decide
to use sane defaults, for the Amazon SE and arx100 we use small fifos
and for the xrx200 and xrx300 SCs a little bit bigger periodic fifo.
The auto detection of max_transfer_size and max_packet_count should
work, so remove it.
This patch is included in OpenWrt for many years.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Link: https://lore.kernel.org/r/20240708222054.2727789-1-hauke@hauke-m.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using dma_map_sg() to map the scatterlist with iommu enabled,
the entries in the scatterlist can be mergerd into less but longer
entries in the function __finalise_sg(). So that the number of
valid mapped entries is actually smaller than ureq->num_reqs,and
there are still some invalid entries in the scatterlist with
dma_addr=0xffffffff and len=0. Writing these invalid sg entries
into the dma_desc can cause a data transmission error.
The function dma_map_sg() returns the number of valid map entries
and the return value is assigned to usb_request::num_mapped_sgs in
function usb_gadget_map_request_by_dev(). So that just write valid
mapped entries into dma_desc according to the usb_request::num_mapped_sgs,
and set the IOC bit if it's the last valid mapped entry.
This patch poses no risk to no-iommu situation, cause
ureq->num_mapped_sgs equals ureq->num_sgs while using dma_direct_map_sg()
to map the scatterlist whith iommu disabled.
Signed-off-by: Peng Hongchi <hongchi.peng@siengine.com>
Link: https://lore.kernel.org/r/20240523100315.7226-1-hongchi.peng@siengine.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added new bitfield GRSTCTL_CLOCK_SWITH_TIMER in GRSTCTL register.
This bitfield applicable HSOTG cores v5.00 or higher and not
applicable to HS/FS IOT devices.
This bitfield must be programmed to 3'b010 if core will be
used in Low-speed and core configured for any HS/FS PHY interface.
This bitfield must be programmed to 3'b111 if core configured
to use either:
- HS PHY interface UTMI or ULPI
- FS PHY any interface
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/0616838cfee958774c9321c6eeeda4be92f900d8.1708948356.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added programmming of ULPI_LATCH_EN_DURING_HIB_ENTRY bit in GPWRDN
register when using ULPI PHY during entry/exit to/from hibernation.
This bit set to 1 during entering to hibernation if ULPI PHY used.
On exiting from hibernation this bit reset to 0.
Applicable for both host and device modes.
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/e024cb39a7177ec201c873df25ca6365f2e55947.1708948356.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added new bit ULPI_LATCH_EN_DURING_HIB_ENTRY in GPWRDN register.
This bit applicable HSOTG cores v5.00 or higher.
Affects Hibernation Entry and Exit sequence (for both Host and Device)
when using ULPI PHY.
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/56d05a4f5750aaa58d8c5bab7705814942a985bd.1708948356.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To support eUSB2 PHY disconnect flow required in Soft disconnect
state set GOTGCTL_EUSB2_DISC_SUPP bit, if applicable.
On Session End Detected interrupt clear PCGCTL_GATEHCLK and
PCGCTL_STOPPCLK bits if eusb2_disc parameter true.
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/9d50b83df693cda8c391313e90048df8dd611c04.1708948356.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added new parameter eusb2_disc to list of core parameters which specify
whether eUSB2 PHY disconnect support flow applicable or no.
Set to false as default value and checked core version if set to true.
This parameter applicable in device mode of HSOTG and HS IOT cores
v5.00 or higher.
Added print this parameter in show parameters of debugfs.
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/e77cc4312bda797d1ddaa4351d86c65a69c8b926.1708948356.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DWC2 IP on the Rockchip SoCs doesn't support clock gating.
When a clock gating is enabled, system hangs.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Link: https://lore.kernel.org/r/1703575199-23638-1-git-send-email-william.wu@rock-chips.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dwc2_hc_n_intr() writes back INTMASK as read but evaluates it
with intmask applied. In stress testing this causes spurious
interrupts like this:
[Mon Aug 14 10:51:07 2023] dwc2 3f980000.usb: dwc2_hc_chhltd_intr_dma: Channel 7 - ChHltd set, but reason is unknown
[Mon Aug 14 10:51:07 2023] dwc2 3f980000.usb: hcint 0x00000002, intsts 0x04600001
[Mon Aug 14 10:51:08 2023] dwc2 3f980000.usb: dwc2_hc_chhltd_intr_dma: Channel 0 - ChHltd set, but reason is unknown
[Mon Aug 14 10:51:08 2023] dwc2 3f980000.usb: hcint 0x00000002, intsts 0x04600001
[Mon Aug 14 10:51:08 2023] dwc2 3f980000.usb: dwc2_hc_chhltd_intr_dma: Channel 4 - ChHltd set, but reason is unknown
[Mon Aug 14 10:51:08 2023] dwc2 3f980000.usb: hcint 0x00000002, intsts 0x04600001
[Mon Aug 14 10:51:08 2023] dwc2 3f980000.usb: dwc2_update_urb_state_abn(): trimming xfer length
Applying INTMASK prevents this. The issue exists in all versions of the
driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Tested-by: Ivan Ivanov <ivan.ivanov@suse.com>
Tested-by: Andrea della Porta <andrea.porta@suse.com>
Link: https://lore.kernel.org/r/20231115144514.15248-1-oneukum@suse.com
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use preferred device_get_match_data() instead of of_match_device() to
get the driver match data. With this, adjust the includes to explicitly
include the correct headers.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20231009211356.3242037-16-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In _dwc2_hcd_urb_enqueue(), "urb->hcpriv = NULL" is executed without
holding the lock "hsotg->lock". In _dwc2_hcd_urb_dequeue():
spin_lock_irqsave(&hsotg->lock, flags);
...
if (!urb->hcpriv) {
dev_dbg(hsotg->dev, "## urb->hcpriv is NULL ##\n");
goto out;
}
rc = dwc2_hcd_urb_dequeue(hsotg, urb->hcpriv); // Use urb->hcpriv
...
out:
spin_unlock_irqrestore(&hsotg->lock, flags);
When _dwc2_hcd_urb_enqueue() and _dwc2_hcd_urb_dequeue() are
concurrently executed, the NULL check of "urb->hcpriv" can be executed
before "urb->hcpriv = NULL". After urb->hcpriv is NULL, it can be used
in the function call to dwc2_hcd_urb_dequeue(), which can cause a NULL
pointer dereference.
This possible bug is found by an experimental static analysis tool
developed by myself. This tool analyzes the locking APIs to extract
function pairs that can be concurrently executed, and then analyzes the
instructions in the paired functions to identify possible concurrency
bugs including data races and atomicity violations. The above possible
bug is reported, when my tool analyzes the source code of Linux 6.5.
To fix this possible bug, "urb->hcpriv = NULL" should be executed with
holding the lock "hsotg->lock". After using this patch, my tool never
reports the possible bug, with the kernelconfiguration allyesconfig for
x86_64. Because I have no associated hardware, I cannot test the patch
in runtime testing, and just verify it according to the code logic.
Fixes: 33ad261aa6 ("usb: dwc2: host: spinlock urb_enqueue")
Signed-off-by: Jia-Ju Bai <baijiaju@buaa.edu.cn>
Link: https://lore.kernel.org/r/20230926024404.832096-1-baijiaju@buaa.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dwc2 driver has everything we need to run in PCI mode except
for pci_device_id driver_data parse. With that to set Loongson
dwc2 element and added identified as PCI_VENDOR_ID_LOONGSON
and PCI_DEVICE_ID_LOONGSON_DWC2 in dwc2_pci_ids, the Loongson
dwc2 controller will work.
Signed-off-by: Yinbo Zhu <zhuyinbo@loongson.cn>
Link: https://lore.kernel.org/r/20230815065833.3375-1-zhuyinbo@loongson.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the controller is dead, the honest answer to the
question whether it has caused an irq is: unknown
As the purpose of the irq return is to trigger switching
off an IRQ, the correct response if you cannot
determine if your device has caused the interrupt is
IRQ_HANDLED
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20230822112455.18957-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Acked-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230718143027.1064731-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230530071913.2192214-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Amlogic A1 uses dwc2 Synopsys IP as its USB peripheral (gadget)
endpoint, with different DWC2 parameters when compared to previous
Amlogic SoCs.
Signed-off-by: Dmitry Rokosov <ddrokosov@sberdevices.ru>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/20230511210455.6634-2-ddrokosov@sberdevices.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dwc2_driver_probe() calls dwc2_lowlevel_hw_init() which deassert some reset
lines.
Should an error happen in dwc2_lowlevel_hw_init() after calling
reset_control_deassert() or in the probe after calling
dwc2_lowlevel_hw_init(), the reset lines remain deasserted.
Add some devm_add_action_or_reset() calls to re-assert the lines if needed.
Update the remove function accordingly.
This change is compile-tested only.
Fixes: 83f8da562f ("usb: dwc2: Add reset control to dwc2")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/c64537b5339342bd00f7c2152b8fc23792b9f95a.1683306479.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for the utmi clock. It's needed on STM32MP15, when using
the integrated full-speed PHY. This clock is an output of USBPHYC, but
HS USBPHYC is not attached as PHY in this case: Full-Speed PHY is directly
managed in dwc2 glue, through GGPIO register. Typical DT when using FS PHY
&usbotg_hs {
compatible = "st,stm32mp15-fsotg", "snps,dwc2";
pinctrl-names = "default";
pinctrl-0 = <&usbotg_hs_pins_a &usbotg_fs_dp_dm_pins_a>;
vbus-supply = <&vbus_otg>;
status = "okay";
};
In this configuration, USBPHYC clock output must be defined, so it can
be properly enabled as a clock provider:
clocks = <&rcc USBO_K>, <&usbphyc>;
clock-names = "otg", "utmi";
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20230414084137.1050487-4-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add error handling in __dwc2_lowlevel_hw_enable() that may leave the
clocks and regulators enabled upon error.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20230414084137.1050487-2-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the USB fixes here, and the USB gadget update for future
development patches to be based on.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When in dual role mode (dr_mode == USB_DR_MODE_OTG), platform probe
successively basically calls:
- dwc2_gadget_init()
- dwc2_hcd_init()
- dwc2_lowlevel_hw_disable() since recent change [1]
- usb_add_gadget_udc()
The PHYs (and so the clocks it may provide) shouldn't be disabled for all
SoCs, in OTG mode, as the HCD part has been initialized.
On STM32 this creates some weird race condition upon boot, when:
- initially attached as a device, to a HOST
- and there is a gadget script invoked to setup the device part.
Below issue becomes systematic, as long as the gadget script isn't
started by userland: the hardware PHYs (and so the clocks provided by the
PHYs) remains disabled.
It ends up in having an endless interrupt storm, before the watchdog
resets the platform.
[ 16.924163] dwc2 49000000.usb-otg: EPs: 9, dedicated fifos, 952 entries in SPRAM
[ 16.962704] dwc2 49000000.usb-otg: DWC OTG Controller
[ 16.966488] dwc2 49000000.usb-otg: new USB bus registered, assigned bus number 2
[ 16.974051] dwc2 49000000.usb-otg: irq 77, io mem 0x49000000
[ 17.032170] hub 2-0:1.0: USB hub found
[ 17.042299] hub 2-0:1.0: 1 port detected
[ 17.175408] dwc2 49000000.usb-otg: Mode Mismatch Interrupt: currently in Host mode
[ 17.181741] dwc2 49000000.usb-otg: Mode Mismatch Interrupt: currently in Host mode
[ 17.189303] dwc2 49000000.usb-otg: Mode Mismatch Interrupt: currently in Host mode
...
The host part is also not functional, until the gadget part is configured.
The HW may only be disabled for peripheral mode (original init), e.g.
dr_mode == USB_DR_MODE_PERIPHERAL, until the gadget driver initializes.
But when in USB_DR_MODE_OTG, the HW should remain enabled, as the HCD part
is able to run, while the gadget part isn't necessarily configured.
I don't fully get the of purpose the original change, that claims disabling
the hardware is missing. It creates conditions on SOCs using the PHY
initialization to be completely non working in OTG mode. Original
change [1] should be reworked to be platform specific.
[1] https://lore.kernel.org/r/20221206-dwc2-gadget-dual-role-v1-2-36515e1092cd@theobroma-systems.com
Fixes: ade23d7b7e ("usb: dwc2: power on/off phy for peripheral mode in dual-role mode")
Cc: stable <stable@kernel.org>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Tested-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Link: https://lore.kernel.org/r/20230315144433.3095859-1-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Each time the platform goes to low power, PM suspend / resume routines
call: __dwc2_lowlevel_hw_enable -> devm_add_action_or_reset().
This adds a new devres each time.
This may also happen at runtime, as dwc2_lowlevel_hw_enable() can be
called from udc_start().
This can be seen with tracing:
- echo 1 > /sys/kernel/debug/tracing/events/dev/devres_log/enable
- go to low power
- cat /sys/kernel/debug/tracing/trace
A new "ADD" entry is found upon each low power cycle:
... devres_log: 49000000.usb-otg ADD 82a13bba devm_action_release (8 bytes)
... devres_log: 49000000.usb-otg ADD 49889daf devm_action_release (8 bytes)
...
A second issue is addressed here:
- regulator_bulk_enable() is called upon each PM cycle (suspend/resume).
- regulator_bulk_disable() never gets called.
So the reference count for these regulators constantly increase, by one
upon each low power cycle, due to missing regulator_bulk_disable() call
in __dwc2_lowlevel_hw_disable().
The original fix that introduced the devm_add_action_or_reset() call,
fixed an issue during probe, that happens due to other errors in
dwc2_driver_probe() -> dwc2_core_reset(). Then the probe fails without
disabling regulators, when dr_mode == USB_DR_MODE_PERIPHERAL.
Rather fix the error path: disable all the low level hardware in the
error path, by using the "hsotg->ll_hw_enabled" flag. Checking dr_mode
has been introduced to avoid a dual call to dwc2_lowlevel_hw_disable().
"ll_hw_enabled" should achieve the same (and is used currently in the
remove() routine).
Fixes: 54c1960605 ("usb: dwc2: Always disable regulators on driver teardown")
Fixes: 33a06f1300 ("usb: dwc2: Fix error path in gadget registration")
Cc: stable <stable@kernel.org>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20230316084127.126084-1-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties.
Convert reading boolean properties to to of_property_read_bool().
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Richard Leitner <richard.leitner@skidata.com>
Link: https://lore.kernel.org/r/20230310144729.1545857-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some boards might use USB-A female connector for USB ports, however,
the port could be connected to a dual-mode USB controller, making it
also behaves as a peripheral device if male-to-male cable is connected.
In this case, the dts looks like this:
&usb0 {
status = "okay";
dr_mode = "otg";
usb-role-switch;
role-switch-default-mode = "host";
};
After boot, dwc2_ovr_init() sets GOTGCTL to GOTGCTL_AVALOVAL and call
dwc2_force_mode() with parameter host=false, which causes inconsistent
mode - The hardware is in peripheral mode while the kernel status is
in host mode.
What we can do now is to call dwc2_drd_role_sw_set() to switch to
device mode, and everything should work just fine now, even switching
back to none(default) mode afterwards.
Fixes: e14acb8769 ("usb: dwc2: drd: add role-switch-default-node support")
Cc: stable <stable@kernel.org>
Signed-off-by: Ziyang Huang <hzyitc@outlook.com>
Tested-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Reviewed-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/SG2PR01MB204837BF68EDB0E343D2A375C9A59@SG2PR01MB2048.apcprd01.prod.exchangelabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
