With this change, the encryption key size is not assumed to be 16 if the
read_encryption_key_size command fails for any reason. This ensures
that if the controller fails the command for any reason that the
encryption key size isn't implicitely set to 16 and instead take a more
concervative posture to assume it is 0.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When handling auto-connected devices, we should execute the rest of the
connection complete when it was previously discovered and it is an ACL
connection.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In bluetooth core specification 4.2,
Vol 2, Part E, 7.8.9 LE Set Advertise Enable Command, it says
The Controller shall continue advertising until ...
or until a connection is created or ...
In these cases, advertising is then disabled.
Hence, advertising would be disabled before a connection is
established. In current kernel implementation, advertising would
be re-enabled when all connections are terminated.
The correct disconnection flow looks like
< HCI Command: Disconnect
> HCI Event: Command Status
Status: Success
> HCI Event: Disconnect Complete
Status: Success
Specifically, the last Disconnect Complete Event would trigger a
callback function hci_event.c:hci_disconn_complete_evt() to
cleanup the connection and re-enable advertising when proper.
However, sometimes, there might occur an exception in the controller
when disconnection is being executed. The disconnection flow might
then look like
< HCI Command: Disconnect
> HCI Event: Command Status
Status: Unknown Connection Identifier
Note that "> HCI Event: Disconnect Complete" is missing when such an
exception occurs. This would result in advertising staying disabled
forever since the connection in question is not cleaned up correctly.
To fix the controller exception issue, we need to do some connection
cleanup when the disconnect command status indicates an error.
Signed-off-by: Joseph Hwang <josephsih@chromium.org>
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To handle BR/EDR devices, we first disable page scan and disconnect all
connected devices. Once that is complete, we add event filters (for
devices that can wake the system) and re-enable page scan.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This change introduces a wide band speech setting which allows higher
level clients to query the local controller support for wide band speech
as well as set the setting state when the radio is powered off.
Internally, this setting controls if erroneous data reporting is enabled
on the controller.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some controllers have been observed to send zero'd events under some
conditions. This change guards against this condition as well as adding
a trace to facilitate diagnosability of this condition.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Attack scenario:
1. A Chromebook (let's call this device A) is paired to a legitimate
Bluetooth classic device (e.g. a speaker) (let's call this device
B).
2. A malicious device (let's call this device C) pretends to be the
Bluetooth speaker by using the same BT address.
3. If device A is not currently connected to device B, device A will
be ready to accept connection from device B in the background
(technically, doing Page Scan).
4. Therefore, device C can initiate connection to device A
(because device A is doing Page Scan) and device A will accept the
connection because device A trusts device C's address which is the
same as device B's address.
5. Device C won't be able to communicate at any high level Bluetooth
profile with device A because device A enforces that device C is
encrypted with their common Link Key, which device C doesn't have.
But device C can initiate pairing with device A with just-works
model without requiring user interaction (there is only pairing
notification). After pairing, device A now trusts device C with a
new different link key, common between device A and C.
6. From now on, device A trusts device C, so device C can at anytime
connect to device A to do any kind of high-level hijacking, e.g.
speaker hijack or mouse/keyboard hijack.
Since we don't know whether the repairing is legitimate or not,
leave the decision to user space if all the conditions below are met.
- the pairing is initialized by peer
- the authorization method is just-work
- host already had the link key to the peer
Signed-off-by: Howard Chung <howardchung@google.com>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This handles LE PHY Update Complete event and store both tx_phy and
rx_phy into hci_conn.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The macro is really not needed and can be replaced with either usage of
bt_err_ratelimited or bt_dev_err_ratelimited.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This reverts commit c49a8682fc.
There are devices which require low connection intervals for usable operation
including keyboards and mice. Forcing a static connection interval for
these types of devices has an impact in latency and causes a regression.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Problem: The Linux Bluetooth stack yields complete control over the BLE
connection interval to the remote device.
The Linux Bluetooth stack provides access to the BLE connection interval
min and max values through /sys/kernel/debug/bluetooth/hci0/
conn_min_interval and /sys/kernel/debug/bluetooth/hci0/conn_max_interval.
These values are used for initial BLE connections, but the remote device
has the ability to request a connection parameter update. In the event
that the remote side requests to change the connection interval, the Linux
kernel currently only validates that the desired value is within the
acceptable range in the Bluetooth specification (6 - 3200, corresponding to
7.5ms - 4000ms). There is currently no validation that the desired value
requested by the remote device is within the min/max limits specified in
the conn_min_interval/conn_max_interval configurations. This essentially
leads to Linux yielding complete control over the connection interval to
the remote device.
The proposed patch adds a verification step to the connection parameter
update mechanism, ensuring that the desired value is within the min/max
bounds of the current connection. If the desired value is outside of the
current connection min/max values, then the connection parameter update
request is rejected and the negative response is returned to the remote
device. Recall that the initial connection is established using the local
conn_min_interval/conn_max_interval values, so this allows the Linux
administrator to retain control over the BLE connection interval.
The one downside that I see is that the current default Linux values for
conn_min_interval and conn_max_interval typically correspond to 30ms and
50ms respectively. If this change were accepted, then it is feasible that
some devices would no longer be able to negotiate to their desired
connection interval values. This might be remedied by setting the default
Linux conn_min_interval and conn_max_interval values to the widest
supported range (6 - 3200 / 7.5ms - 4000ms). This could lead to the same
behavior as the current implementation, where the remote device could
request to change the connection interval value to any value that is
permitted by the Bluetooth specification, and Linux would accept the
desired value.
Signed-off-by: Carey Sonsino <csonsino@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Changes made to add HCI Write Authenticated Payload timeout
command for LE Ping feature.
As per the Core Specification 5.0 Volume 2 Part E Section 7.3.94,
the following code changes implements
HCI Write Authenticated Payload timeout command for LE Ping feature.
Signed-off-by: Spoorthi Ravishankar Koppad <spoorthix.k@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This commit makes the kernel not send the next queued HCI command until
a command complete arrives for the last HCI command sent to the
controller. This change avoids a problem with some buggy controllers
(seen on two SKUs of QCA9377) that send an extra command complete event
for the previous command after the kernel had already sent a new HCI
command to the controller.
The problem was reproduced when starting an active scanning procedure,
where an extra command complete event arrives for the LE_SET_RANDOM_ADDR
command. When this happends the kernel ends up not processing the
command complete for the following commmand, LE_SET_SCAN_PARAM, and
ultimately behaving as if a passive scanning procedure was being
performed, when in fact controller is performing an active scanning
procedure. This makes it impossible to discover BLE devices as no device
found events are sent to userspace.
This problem is reproducible on 100% of the attempts on the affected
controllers. The extra command complete event can be seen at timestamp
27.420131 on the btmon logs bellow.
Bluetooth monitor ver 5.50
= Note: Linux version 5.0.0+ (x86_64) 0.352340
= Note: Bluetooth subsystem version 2.22 0.352343
= New Index: 80:C5:F2:8F:87:84 (Primary,USB,hci0) [hci0] 0.352344
= Open Index: 80:C5:F2:8F:87:84 [hci0] 0.352345
= Index Info: 80:C5:F2:8F:87:84 (Qualcomm) [hci0] 0.352346
@ MGMT Open: bluetoothd (privileged) version 1.14 {0x0001} 0.352347
@ MGMT Open: btmon (privileged) version 1.14 {0x0002} 0.352366
@ MGMT Open: btmgmt (privileged) version 1.14 {0x0003} 27.302164
@ MGMT Command: Start Discovery (0x0023) plen 1 {0x0003} [hci0] 27.302310
Address type: 0x06
LE Public
LE Random
< HCI Command: LE Set Random Address (0x08|0x0005) plen 6 #1 [hci0] 27.302496
Address: 15:60:F2:91:B2:24 (Non-Resolvable)
> HCI Event: Command Complete (0x0e) plen 4 #2 [hci0] 27.419117
LE Set Random Address (0x08|0x0005) ncmd 1
Status: Success (0x00)
< HCI Command: LE Set Scan Parameters (0x08|0x000b) plen 7 #3 [hci0] 27.419244
Type: Active (0x01)
Interval: 11.250 msec (0x0012)
Window: 11.250 msec (0x0012)
Own address type: Random (0x01)
Filter policy: Accept all advertisement (0x00)
> HCI Event: Command Complete (0x0e) plen 4 #4 [hci0] 27.420131
LE Set Random Address (0x08|0x0005) ncmd 1
Status: Success (0x00)
< HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2 #5 [hci0] 27.420259
Scanning: Enabled (0x01)
Filter duplicates: Enabled (0x01)
> HCI Event: Command Complete (0x0e) plen 4 #6 [hci0] 27.420969
LE Set Scan Parameters (0x08|0x000b) ncmd 1
Status: Success (0x00)
> HCI Event: Command Complete (0x0e) plen 4 #7 [hci0] 27.421983
LE Set Scan Enable (0x08|0x000c) ncmd 1
Status: Success (0x00)
@ MGMT Event: Command Complete (0x0001) plen 4 {0x0003} [hci0] 27.422059
Start Discovery (0x0023) plen 1
Status: Success (0x00)
Address type: 0x06
LE Public
LE Random
@ MGMT Event: Discovering (0x0013) plen 2 {0x0003} [hci0] 27.422067
Address type: 0x06
LE Public
LE Random
Discovery: Enabled (0x01)
@ MGMT Event: Discovering (0x0013) plen 2 {0x0002} [hci0] 27.422067
Address type: 0x06
LE Public
LE Random
Discovery: Enabled (0x01)
@ MGMT Event: Discovering (0x0013) plen 2 {0x0001} [hci0] 27.422067
Address type: 0x06
LE Public
LE Random
Discovery: Enabled (0x01)
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In ext_adv_report_event rssi comes before data (not after data as
in legacy adv_report_evt) so "+ 1" is not required in the ptr arithmatic
to point to next report.
Signed-off-by: Jaganath Kanakkassery <jaganath.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.
So, change the following form:
sizeof(*ev) + ev->num_hndl * sizeof(struct hci_comp_pkts_info)
to :
struct_size(ev, handles, ev->num_hndl)
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In case a command which completes in Command Status was sent using the
hci_cmd_send-family of APIs there would be a misleading error in the
hci_get_cmd_complete function, since the code would be trying to fetch
the Command Complete parameters when there are none.
Avoid the misleading error and silently bail out from the function in
case the received event is a command status.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The check on status is redundant as a status has to be zero at
the point it is being checked because of a previous check and return
path via label 'unlock'. Remove the redundant check and the deadcode
that can never be reached.
Detected by CoverityScan, CID#1471710 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add the definitions for adding entries to the LE resolve list and
removing entries from the LE resolve list. When the LE resolve list
gets changed via HCI commands make sure that the internal storage of
the resolve list entries gets updated.
Signed-off-by: Ankit Navik <ankit.p.navik@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add the definitions for LE address resolution enable HCI commands.
When the LE address resolution enable gets changed via HCI commands
make sure that flag gets updated.
Signed-off-by: Ankit Navik <ankit.p.navik@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Variables 'adv_set' and 'cp' are being assigned but are never used hence
they are redundant and can be removed.
Cleans up clang warnings:
net/bluetooth/hci_event.c:1135:29: warning: variable 'adv_set' set but not used [-Wunused-but-set-variable]
net/bluetooth/mgmt.c:3359:39: warning: variable 'cp' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This event comes after connection complete event for incoming
connections. Since we now have different random address for
each instance, conn resp address is assigned from this event.
As of now only connection part is handled as we are not
enabling duration or max num of events while starting ext adv.
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This basically sets the random address for the adv instance
Random address can be set only if the instance is created which
is done in Set ext adv param.
Random address and rpa expire timer and flags have been added
to adv instance which will be used when the respective
instance is scheduled.
This introduces a hci_get_random_address() which returns the
own address type and random address (rpa or nrpa) based
on the instance flags and hdev flags. New function is required
since own address type should be known before setting adv params
but address can be set only after setting params.
< HCI Command: LE Set Advertising Set Random Address (0x08|0x0035) plen 7
Advertising handle: 0x00
Advertising random address: 3C:8E:56:9B:77:84 (OUI 3C-8E-56)
> HCI Event: Command Complete (0x0e) plen 4
LE Set Advertising Set Random Address (0x08|0x0035) ncmd 1
Status: Success (0x00)
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If ext adv is enabled then use ext adv to disable as well.
Also remove the adv set during LE disable.
< HCI Command: LE Set Extended Advertising Enable (0x08|0x0039) plen 2
Extended advertising: Disabled (0x00)
Number of sets: Disable all sets (0x00)
> HCI Event: Command Complete (0x0e) plen 4
LE Set Extended Advertising Enable (0x08|0x0039) ncmd 2
Status: Success (0x00)
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch implements Set Ext Adv data and Set Ext Scan rsp data
if controller support extended advertising.
Currently the operation is set as Complete data and fragment
preference is set as no fragment
< HCI Command: LE Set Extended Advertising Data (0x08|0x0037) plen 35
Handle: 0x00
Operation: Complete extended advertising data (0x03)
Fragment preference: Minimize fragmentation (0x01)
Data length: 0x15
16-bit Service UUIDs (complete): 2 entries
Heart Rate (0x180d)
Battery Service (0x180f)
Name (complete): Test LE
Company: Google (224)
Data: 0102
> HCI Event: Command Complete (0x0e) plen 4
LE Set Extended Advertising Data (0x08|0x0037) ncmd 1
Status: Success (0x00)
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch basically replaces legacy adv with extended adv
based on the controller support. Currently there is no
design change. ie only one adv set will be enabled at a time.
This also adds tx_power in instance and store whatever returns
from Set_ext_parameter, use the same in adv data as well.
For instance 0 tx_power is stored in hdev only.
< HCI Command: LE Set Extended Advertising Parameters (0x08|0x0036) plen 25
Handle: 0x00
Properties: 0x0010
Use legacy advertising PDUs: ADV_NONCONN_IND
Min advertising interval: 1280.000 msec (0x0800)
Max advertising interval: 1280.000 msec (0x0800)
Channel map: 37, 38, 39 (0x07)
Own address type: Random (0x01)
Peer address type: Public (0x00)
Peer address: 00:00:00:00:00:00 (OUI 00-00-00)
Filter policy: Allow Scan Request from Any, Allow Connect Request from Any (0x00)
TX power: 127 dbm (0x7f)
Primary PHY: LE 1M (0x01)
Secondary max skip: 0x00
Secondary PHY: LE 1M (0x01)
SID: 0x00
Scan request notifications: Disabled (0x00)
> HCI Event: Command Complete (0x0e) plen 5
LE Set Extended Advertising Parameters (0x08|0x0036) ncmd 1
Status: Success (0x00)
TX power (selected): 7 dbm (0x07)
< HCI Command: LE Set Extended Advertising Enable (0x08|0x0039) plen 6
Extended advertising: Enabled (0x01)
Number of sets: 1 (0x01)
Entry 0
Handle: 0x00
Duration: 0 ms (0x00)
Max ext adv events: 0
> HCI Event: Command Complete (0x0e) plen 4
LE Set Extended Advertising Enable (0x08|0x0039) ncmd 2
Status: Success (0x00)
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch reads the number of advertising sets in the controller
during init and save it in hdev.
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch defines the extended ADV types and handle it in ADV report.
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This implements extended LE craete connection and enhanced
LE conn complete event if the controller supports.
For now it is as good as legacy LE connection and event as
no new features in the extended connection is handled.
< HCI Command: LE Extended Create Connection (0x08|0x0043) plen 26
Filter policy: White list is not used (0x00)
Own address type: Public (0x00)
Peer address type: Random (0x01)
Peer address: DB:7E:2E:1D:85:E8 (Static)
Initiating PHYs: 0x01
Entry 0: LE 1M
Scan interval: 60.000 msec (0x0060)
Scan window: 60.000 msec (0x0060)
Min connection interval: 50.00 msec (0x0028)
Max connection interval: 70.00 msec (0x0038)
Connection latency: 0 (0x0000)
Supervision timeout: 420 msec (0x002a)
Min connection length: 0.000 msec (0x0000)
Max connection length: 0.000 msec (0x0000)
> HCI Event: Command Status (0x0f) plen 4
LE Extended Create Connection (0x08|0x0043) ncmd 2
Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 31
LE Enhanced Connection Complete (0x0a)
Status: Success (0x00)
Handle: 3585
Role: Master (0x00)
Peer address type: Random (0x01)
Peer address: DB:7E:2E:1D:85:E8 (Static)
Local resolvable private address: 00:00:00:00:00:00 (Non-Resolvable)
Peer resolvable private address: 00:00:00:00:00:00 (Non-Resolvable)
Connection interval: 67.50 msec (0x0036)
Connection latency: 0 (0x0000)
Supervision timeout: 420 msec (0x002a)
Master clock accuracy: 0x00
@ MGMT Event: Device Connected (0x000b) plen 40
LE Address: DB:7E:2E:1D:85:E8 (Static)
Flags: 0x00000000
Data length: 27
Name (complete): Designer Mouse
Appearance: Mouse (0x03c2)
Flags: 0x05
LE Limited Discoverable Mode
BR/EDR Not Supported
16-bit Service UUIDs (complete): 1 entry
Human Interface Device (0x1812)
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This is done so that the helpers can be used for extended conn
implementation which will be done in subsequent patch.
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch enables Extended ADV report event if extended scanning
is supported in the controller and process the same.
The new features are not handled and for now its as good as
legacy ADV report.
> HCI Event: LE Meta Event (0x3e) plen 53
LE Extended Advertising Report (0x0d)
Num reports: 1
Entry 0
Event type: 0x0013
Props: 0x0013
Connectable
Scannable
Use legacy advertising PDUs
Data status: Complete
Legacy PDU Type: ADV_IND (0x0013)
Address type: Random (0x01)
Address: DB:7E:2E:1A:85:E8 (Static)
Primary PHY: LE 1M
Secondary PHY: LE 1M
SID: 0x00
TX power: 0 dBm
RSSI: -90 dBm (0xa6)
Periodic advertising invteral: 0.00 msec (0x0000)
Direct address type: Public (0x00)
Direct address: 00:00:00:00:00:00 (OUI 00-00-00)
Data length: 0x1b
0f 09 44 65 73 69 67 6e 65 72 20 4d 6f 75 73 65 ..Designer Mouse
03 19 c2 03 02 01 05 03 03 12 18 ...........
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This implements Set extended scan param and set extended scan enable
commands and use it for start LE scan based on controller support.
The new features added in these commands are setting of new PHY for
scanning and setting of scan duration. Both features are disabled
for now, meaning only 1M PHY is set and scan duration is set to 0
which means that scanning will be done untill scan disable is called.
< HCI Command: LE Set Extended Scan Parameters (0x08|0x0041) plen 8
Own address type: Random (0x01)
Filter policy: Accept all advertisement (0x00)
PHYs: 0x01
Entry 0: LE 1M
Type: Active (0x01)
Interval: 11.250 msec (0x0012)
Window: 11.250 msec (0x0012)
> HCI Event: Command Complete (0x0e) plen 4
LE Set Extended Scan Parameters (0x08|0x0041) ncmd 1
Status: Success (0x00)
< HCI Command: LE Set Extended Scan Enable (0x08|0x0042) plen 6
Extended scan: Enabled (0x01)
Filter duplicates: Enabled (0x01)
Duration: 0 msec (0x0000)
Period: 0.00 sec (0x0000)
> HCI Event: Command Complete (0x0e) plen 4
LE Set Extended Scan Enable (0x08|0x0042) ncmd 2
Status: Success (0x00)
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Introduce a helper hci_req_start_scan() which starts an LE
scan and call it from passive_Scan() and active_scan().
There is not functionality change in this patch.
This is basically done to enable extended scanning if the
controller supports which will be done in the subsequent
patch
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There are some controllers sending out advertising data with illegal
length value which is longer than HCI_MAX_AD_LENGTH, causing the
buffer last_adv_data overflows. To avoid these controllers from
overflowing the buffer, we do not process the advertisement data
if its length is incorrect.
Signed-off-by: Chriz Chow <chriz.chow@aminocom.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In case of using BT_ERR and BT_INFO, convert to bt_dev_err and
bt_dev_info when possible. This allows for controller specific
reporting.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
trivial fix to spelling mistake in BT_ERR_RATELIMITED error message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The HCI_BREDR naming is confusing since it actually stands for Primary
Bluetooth Controller. Which is a term that has been used in the latest
standard. However from a legacy point of view there only really have
been Basic Rate (BR) and Enhanced Data Rate (EDR). Recent versions of
Bluetooth introduced Low Energy (LE) and made this terminology a little
bit confused since Dual Mode Controllers include BR/EDR and LE. To
simplify this the name HCI_PRIMARY stands for the Primary Controller
which can be a single mode or dual mode controller.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In case of buggy controllers send advertising packet types that we
don't know of we should simply ignore them instead of trying to react
to them in some (potentially wrong) way.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To make the EIR parsing helper more general purpose, make it return
the found data and its length rather than just saying whether the data
was present or not.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This paves the way for eventually performing advertising changes
through the hdev->req_workqueue. Some new APIs need to be exposed from
mgmt.c to hci_request.c and vice-versa, but many of them will go away
once hdev->req_workqueue gets used.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since Add/Remove Device perform the page scan updates independently
from the HCI command completion we've introduced a potential race when
multiple mgmt commands are queued. Doing the page scan updates through
the req_workqueue ensures that the state changes are performed in a
race-free manner.
At the same time, to make the request helper more widely usable,
extend it to also cover Inquiry Scan changes since those are behind
the same HCI command. This is also reflected in the new name of the
API as well as the work struct name.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The SKB context buffer for HCI request is really not just for requests,
information in their are preserved for the whole HCI layer. So it makes
more sense to actually rename it into bt_cb()->hci and also call it then
struct hci_ctrl.
In addition that allows moving the decoded opcode for outgoing packets
into that struct. So far it was just consuming valuable space from the
main shared items. And opcode are not valid for L2CAP packets.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Use the new hci_conn_hash_lookup_le() API to look up LE connections.
This way we're guaranteed exact matches that also take into account
the address type.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Conflicts:
drivers/net/usb/asix_common.c
net/ipv4/inet_connection_sock.c
net/switchdev/switchdev.c
In the inet_connection_sock.c case the request socket hashing scheme
is completely different in net-next.
The other two conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
We can't use hci_explicit_connect_lookup() since that would only cover
explicit connections, leaving normal reconnections completely
untouched. Not using it in turn means leaving out entries in
pend_le_reports.
To fix this and simplify the logic move conn params from the reports
list to the pend_le_conns list for the duration of an explicit
connect. Once the connect is complete move the params back to the
pend_le_reports list. This also means that the explicit connect lookup
function only needs to look into the pend_le_conns list.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When disable/enable scan command is issued twice, some controllers
will return an error for the second request, i.e. requests with this
command will fail on some controllers, and succeed on others.
This patch makes sure that unnecessary scan disable/enable commands
are not issued.
When adding device to the auto connect whitelist when there is pending
connect attempt, there is no need to update scan.
hci_connect_le_scan_cleanup is conditionally executing
hci_conn_params_del, that is calling hci_update_background_scan. Make
the other case also update scan, and remove reduntand call from
hci_connect_le_scan_remove.
When stopping interleaved discovery the state should be set to stopped
only when both LE scanning and discovery has stopped.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently, when trying to connect to already paired device that just
rotated its RPA MAC address, old address would be used and connection
would fail. In order to fix that, kernel must scan and receive
advertisement with fresh RPA before connecting.
This path makes sure that after advertisement is received from device that
we try to connect to, it is properly handled in check_pending_le_conn and
trigger connect attempt.
It also modifies hci_le_connect to make sure that connect attempt will be
properly continued.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds hci_lookup_le_connect method, that will be used to check
wether outgoing le connection attempt is in progress.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To avoid a2mp module hooks from hci_event.c and send
getinfo response operation only required by a2mp module,
we can move this callback to a2mp.c
Signed-off-by: Arron Wang <arron.wang@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The encryption key size is read only for BR/EDR (ACL_LINK) connections
so there's no need to check for it in the read_enc_key_size_complete()
callback.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since Bluetooth 3.0 there's a HCI command available for reading the
encryption key size of an BR/EDR connection. This information is
essential e.g. for generating an LTK using SMP over BR/EDR, so store
it as part of struct hci_conn.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Checking for SC-only mode requirements when we get an encrypt change
event shouldn't be limited to the BT_CONFIG state but done any time
encryption changes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The encryption key size for LTKs is supposed to be applied only at the
moment of encryption. When generating a Link Key (using LE SC) from
the LTK the full non-shortened value should be used. This patch
modifies the code to always keep the full value around and only apply
the key size when passing the value to HCI.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When establishing a Bluetooth LE connection, read the remote used
features mask to determine which features are supported. This was
not really needed with Bluetooth 4.0, but since Bluetooth 4.1 and
also 4.2 have introduced new optional features, this becomes more
important.
This works the same as with BR/EDR where the connection enters the
BT_CONFIG stage and hci_connect_cfm call is delayed until the remote
features have been retrieved. Only after successfully receiving the
remote features, the connection enters the BT_CONNECTED state.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Now that there's a HCI request API available where the callback receives
the resulting skb, we can convert the local OOB data reading to use this
new API. This patch does the necessary update in mgmt.c (which also
requires moving the callback higher up since it's now a static function)
and removes the custom calls from hci_event.c that are no-longer
necessary.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To make the hci_req_run_skb() API consistent with hci_cmd_sync_ev()
the callback should receive the cmd_complete parameters in the 'normal'
case and the full HCI event if a special event was expected. This patch
moves the hci_get_cmd_complete() function from hci_core.c to hci_event.c
where it's used to strip the skb from the needed headers before passing
it on to the callback.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now that the synchronous HCI requests use the new API and a new private
variable the recv_evt member of hci_dev is no-longer needed. This patch
removes it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a second possible callback for HCI requests where the
callback will receive the full skb of the last successfully completed
HCI command. This API is useful for cases where we want to use a request
to read some data and the existing hci_event.c handlers do not store it
e.g. in the hci_dev struct.
The reason the patch is a bit bigger than just adding the new API is
because the hci_req_cmd_complete() functions required some refactoring
to enable it: now hci_req_cmd_complete() is simply used to request the
callback pointers if any, and the actual calling of them happens from a
single place at the end of hci_event_packet(). The reason for this is
that we need to pass the original skb (without any skb_pull, etc
modifications done to it) and it's simplest to keep track of it within
the hci_event_packet() function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When dealing with HCI command status events, the reasoning for trying to
mark a request as complete if no specific event is being waited for and
status was success is not self-evident. This patch adds a clarifying
comment above the if-statement.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In order to shrink the size of bt_skb_cb, this patch moves the HCI
request related variables into their own req_ctrl struct. Additionall
the L2CAP and HCI request structs are placed inside the same union since
they will never be used at the same time for the same skb.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
During the HCI init phase a completed request might be the last part of
the setup procedure after which the actual init procedure starts. The
init procedure begins with a call to hci_reset_req() which sets the
HCI_RESET flag. The purpose of this flag is to make us ignore any
updates to ncmd/cmd_cnt as long as we haven't received the command
complete event for the HCI_Reset. There's a potential race with this
however:
hci_req_cmd_complete(hdev, opcode, status);
if (ev->ncmd && !test_bit(HCI_RESET, &hdev->flags)) {
atomic_set(&hdev->cmd_cnt, 1);
if (!skb_queue_empty(&hdev->cmd_q))
queue_work(hdev->workqueue, &hdev->cmd_work);
}
Since the hci_req_cmd_complete() will trigger the completion of the
setup stage, it's possible that hci_reset_req() gets called before we
try to read ev->ncmd and the HCI_RESET flag. Because of this the cmd_cnt
would never be updated and the hci_reset_req() in practice ends up
blocking itself.
This patch fixes the issue by updating cmd_cnt before notifying the
request completion, and then reading it again to determine whether the
cmd_work should be queued or not.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When doing scan through mgmt api, some controllers can do both le and
classic scan at same time. They can be distinguished by
HCI_QUIRK_SIMULTANEOUS_DISCOVERY set.
This patch enables them to use this feature when doing dual mode scan.
Instead of doing le, then classic scan, both scans are run at once.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The HCI_CONN_REMOTE_OOB connection flag is used to indicate if the
pairing initiator has provided out-of-band data. However since that
value is no longer used in any decision making, just remove it.
It is actually unclear what purpose the OOB data present field from
the HCI IO Capability Response event serves in the first place. If
either side provided out-of-band data, then that data will be used
for pairing.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When only the pairing initiator is providing out-of-band data, then
the receiver side was ignoring the data. For some reason the code was
checking if the initiator has received out-of-band data and only then
also provide the required inidication that the acceptor actually has
the needed data available.
For BR/EDR out-of-band pairing it is enough if one side has received
out-of-band data. There are no extra checks needed here to make this
work smoothly. The only thing that is needed is to tell the controller
if data is present (and if it is P-192 or P-256 or both) and then let
the controller actually figure out the rest.
This means the check for outgoing connection or if the initiator has
indicated data are completely pointless and are in fact actually
causing harm. The check in question is this one:
if (conn->out || test_bit(HCI_CONN_REMOTE_OOB, &conn->flags)) {
After just taking the conditional check out and always executing the
code for determining the type of out-of-band data, the pairing works
flawlessly and prodcudes authenticated link keys.
The patch itself looks more complicated due to the reformatting of the
indentation, but it essentially just a two-line change.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hdev->dev_flags field has outgrown itself on 32-bit systems. So
instead of hacking around it, switch to using DECLARE_BITMAP.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Instead of manually coding test_and_clear_bit on hdev->dev_flags all the
time, use hci_dev_test_and_clear_flag helper macro.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Instead of manually coding clear_bit on hdev->dev_flags all the time,
use hci_dev_clear_flag helper macro.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Instead of manually coding set_bit on hdev->dev_flags all the time,
use hci_dev_set_flag helper macro.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Instead of manually coding test_bit on hdev->dev_flags all the time,
use hci_dev_test_flag helper macro.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-03-02
Here's the first bluetooth-next pull request targeting the 4.1 kernel:
- ieee802154/6lowpan cleanups
- SCO routing to host interface support for the btmrvl driver
- AMP code cleanups
- Fixes to AMP HCI init sequence
- Refactoring of the HCI callback mechanism
- Added shutdown routine for Intel controllers in the btusb driver
- New config option to enable/disable Bluetooth debugfs information
- Fix for early data reception on L2CAP fixed channels
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
struct hci_req_ctrl is never used outside of struct bt_skb_cb;
Inlining it frees 8 bytes on a 64 bit system in skb->cb[] allowing
the addition of more ancillary data.
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves all the disconn_cfm callbacks to be based on the hci_cb
list. This means making l2cap_disconn_cfm private to l2cap_core.c and
sco_conn_cb private to sco.c respectively. Since the hci_conn type
filtering isn't done any more on the wrapper level the callbacks
themselves need to check that they were passed a relevant type of
connection.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch moves all the connect_cfm callbacks to be based on the hci_cb
list. This means making l2cap_connect_cfm private to l2cap_core.c and
sco_connect_cb private to sco.c respectively. Since the hci_conn type
filtering isn't done any more on the wrapper level the callbacks
themselves need to check that they were passed a relevant type of
connection.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When using Secure Connections Only mode, then only P-256 OOB data is
valid and should be provided. In case userspace provides P-192 and P-256
OOB data, then the P-192 values will be set to zero. However the present
value of the IO capability exchange still mentioned that both values
would be available. Fix this by telling the controller clearly that only
the P-256 OOB data is present.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the HCI Write Simple Pairing Debug Mode command has been issued,
the result needs to be tracked and stored. The hdev->ssp_debug_mode
variable is already present, but was never updated when the mode in
the controller was actually changed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When BR/EDR Secure Connections has been enabled, the OOB data present
value can take 2 additional values. The host has to clearly provide
details about if P-192 OOB data, P-256 OOB data or a combination of
P-192 and P-256 OOB data is present.
In case BR/EDR Secure Connections is not enabled or not supported,
then check that P-192 OOB data is actually present and return the
correct value based on that.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When receiving a HCI Hardware Error event, the controller should be
assumed to be non-functional until issuing a HCI Reset command.
The Bluetooth hardware errors are vendor specific and so add a
new hdev->hw_error callback that drivers can provide to run extra
code to handle the hardware error.
After completing the vendor specific error handling perform a full
reset of the Bluetooth stack by closing and re-opening the transport.
Based-on-patch-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When HCI_Reset is issued the discovery state is assumed to be stopped.
The hci_cc_reset() handler was trying to set the state but it was doing
it without using the hci_discovery_set_state() function. Because of this
e.g. the mgmt Discovering event could go without being sent. This patch
fixes the code to use the hci_discovery_set_state() function instead of
just blindly setting the state value.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If Secure Connections Only mode has been enabled, the it is important
to check that OOB data for P-256 values is provided. In case it is not,
then tell the remote side that no OOB data is present.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When replying to the IO capability request for Secure Simple Pairing and
Secure Connections, the OOB data present fields needs to set. Instead of
making the calculation inline, split this into a separate helper
function.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When Secure Connections Only mode has been enabled and remote OOB data
is requested, then only provide P-256 hash and randomizer vaulues. The
fields for P-192 hash and randomizer should be set to zero.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch converts the Set Secure Connection HCI handling to use a HCI
request instead of using a hard-coded callback in hci_event.c. This e.g.
ensures that we don't clear the flags incorrectly if something goes
wrong with the power up process (not related to a mgmt Set SC command).
The code can also be simplified a bit since only one pending Set SC
command is allowed, i.e. mgmt_pending_foreach usage is not needed.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the HCI Delete Stored Link Key command completes, then update the
value of current stored keys in hci_dev structure.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the HCI Read Stored Link Keys command completes it gives useful
information of the current stored keys and maximum keys a controller
can actually store. So process this event and store these information
in hci_dev structure.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Johan Hedberg say:
====================
pull request: bluetooth-next 2014-12-31
Here's the first batch of bluetooth patches for 3.20.
- Cleanups & fixes to ieee802154 drivers
- Fix synchronization of mgmt commands with respective HCI commands
- Add self-tests for LE pairing crypto functionality
- Remove 'BlueFritz!' specific handling from core using a new quirk flag
- Public address configuration support for ath3012
- Refactor debugfs support into a dedicated file
- Initial support for LE Data Length Extension feature from Bluetooth 4.2
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When connectable mode is enabled (page scan on) through some non-mgmt
method the HCI_CONNECTABLE flag will not be set. For backwards
compatibility with user space versions not using mgmt we should not
require HCI_CONNECTABLE to be set if HCI_MGMT is not set.
Reported-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org # 3.17+
When controllers set the HCI_QUIRK_INVALID_BDADDR flag, it is required
by userspace to program a valid public Bluetooth device address into
the controller before it can be used.
After successful address configuration, the internal state changes and
the controller runs the complete initialization procedure. However one
small difference is that this is no longer the HCI_SETUP stage. The
HCI_SETUP stage is only valid during initial controller setup. In this
case the stack runs the initialization as part of the HCI_CONFIG stage.
The controller version information, default name and supported commands
are only stored during HCI_SETUP. While these information are static,
they are not read initially when HCI_QUIRK_INVALID_BDADDR is set. So
when running in HCI_CONFIG state, these information need to be updated
as well.
This especially impacts Bluetooth 4.1 and later controllers using
extended feature pages and second event mask page.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org # 3.17+
For every internal representation of a Bluetooth connection which is
identified by hci_conn, create a debugfs directory with the handle
number as directory name.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the controller supports the LE Data Length Extension feature, the
default and maximum data length are read and now stored.
For backwards compatibility all values are initialized to the data
length values from Bluetooth 4.1 and earlier specifications.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
None of the hci_request related things in net/bluetooth/hci_core.h are
needed anywhere outside of the core bluetooth module. This patch creates
a new net/bluetooth/hci_request.c file with its corresponding h-file and
moves the functionality there from hci_core.c and hci_core.h.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To keep the parameter list and its semantics clear it makes sense to
split the hci_update_page_scan function into two separate functions: one
taking a hci_dev and another taking a hci_request. The one taking a
hci_dev constructs its own hci_request and then calls the other
function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
mgmt_pending_remove() should be called with hci_dev_lock protection and
all hci_event.c functions which calls mgmt_complete() (which eventually
calls mgmt_pending_remove()) should hold the lock.
So this patch fixes the same
Signed-off-by: Jaganath Kanakkassery <jaganath.k@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the controller sends a LE Direct Advertising Report event, the host
must confirm that the resolvable random address provided matches with
its own identity resolving key. If it does, then that advertising report
needs to be processed. If it does not match, the report needs to be
ignored.
This patch adds full support for handling these new reports and using
them for device discovery and connection handling. This means when a
Bluetooth controller supports the Extended Scanner Filter Policies, it
is possible to use directed advertising with LE privacy.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When no RSSI value is available then make sure that the result is
filtered out when the RSSI threshold filter is active.
This means that all Bluetooth 1.1 or earlier devices will not
report any results when using a RSSI threshold filter.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
To be able to support OOB data for LE pairing we need to store the
address type of the remote device. This patch extends the relevant
functions and data types with a bdaddr_type variable.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For LE Secure Connections we want to trigger cross transport key
generation only if a new link key was actually created during the BR/EDR
connection. This patch adds a new flag to track this information.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now that hci_find_ltk_by_addr is the only LTK lookup function there's no
need to keep the long name anymore. This patch shortens the function
name to simply hci_find_ltk.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
LTKs derived from Secure Connections based pairing are symmetric, i.e.
they should match both master and slave role. This patch updates the LTK
lookup functions to ignore the desired role when dealing with SC LTKs.
Furthermore, with Secure Connections the EDiv and Rand values are not
used and should always be set to zero. This patch updates the LTK lookup
to first use the bdaddr as key and then do the necessary verifications
of EDiv and Rand based on whether the found LTK is for SC or not.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since the HCI_SC_ENABLED flag will also be used for controllers without
BR/EDR Secure Connections support whenever we need to check specifically
for SC for BR/EDR we also need to check that the controller actually
supports it. This patch adds a convenience macro for check all the
necessary conditions and converts the places in the code that need it to
use it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we get a Link Key Notification HCI event we should already have a
hci_conn object. This should have been created either in the Connection
Request event handler, the hci_connect_acl() function or the
hci_cs_create_conn() function (if the request was not sent by the
kernel).
Since the only case that we'd end up not having a hci_conn in the Link
Key Notification event handler would be essentially broken hardware it's
safe to simply bail out from the function if this happens.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch converts the hdev->link_keys list to be protected through
RCU, thereby eliminating the need to hold the hdev lock while accessing
the list.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When a connection is requested the conn->pending_sec_level value gets
set to whatever level the user requested the connection to be. During
the pairing process there are various sanity checks to try to ensure
that the right length PIN or right IO Capability is used to satisfy the
target security level. However, when we finally get hold of the link key
that is to be used we should still set the actual final security level
from the key type.
This way when we eventually get an Encrypt Change event the correct
value gets copied to conn->sec_level.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The common short form of "randomizer" is "rand" in many places
(including the Bluetooth specification). The shorter version also makes
for easier to read code with less forced line breaks. This patch renames
all occurences of "randomizer" to "rand" in the Bluetooth subsystem
code.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch set converts the hdev->long_term_keys list to use RCU to
eliminate the need to use hci_dev_lock/unlock.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch fixes a regression that was introduced by commit
cb77c3ec07. In addition to BT_CONFIG,
BT_CONNECTED is also a state in which we may get a remote name and need
to indicate over mgmt the connection status. This scenario is
particularly likely to happen for incoming connections that do not need
authentication since there the hci_conn state will reach BT_CONNECTED
before the remote name is received.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Opcodes in switch/case in hci_cmd_status_evt are not sorted
by value. This patch restores proper ordering.
Signed-off-by: Kuba Pawlak <kubax.t.pawlak@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If role switch was rejected by the controller and HCI Event: Command Status
returned with status "Command Disallowed" (0x0C) the flag
HCI_CONN_RSWITCH_PEND remains set. No further role switches are
possible as this flag prevents us from sending any new HCI Switch Role
requests and the only way to clear it is to receive a valid
HCI Event Switch Role.
This patch clears the flag if command was rejected.
2013-01-01 00:03:44.209913 < HCI Command: Switch Role (0x02|0x000b) plen 7
bdaddr BC:C6:DB:C4:6F:79 role 0x00
Role: Master
2013-01-01 00:03:44.210867 > HCI Event: Command Status (0x0f) plen 4
Switch Role (0x02|0x000b) status 0x0c ncmd 1
Error: Command Disallowed
Signed-off-by: Kuba Pawlak <kubax.t.pawlak@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the HCI_Hardware_Error event is send by the controller or
injected by the driver, then at least print an error message.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the HCI_Reset command returns, the status needs to be checked. It
is unlikely that HCI_Reset actually fails, but when it fails, it is a
bad idea to reset all values since the controller will have not reset
its values in that case.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The internal representation of the LE white list needs to be cleared
when receiving a successful HCI_Reset command. A reset of the controller
is expected to start with an empty LE white list.
When the LE white list is not cleared on controller reset, the passive
background scanning might skip programming the remote devices. Only
changes to the LE white list are programmed when passive background
is started.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org # 3.17.x
There are scenarios when autoconnecting to a device after the
reception of an ADV_IND report (action 0x02), in which userland
might want to examine the report's contents.
For instance, the Service Data might have changed and it would be
useful to know ahead of time before starting any GATT procedures.
Also, the ADV_IND may contain Manufacturer Specific data which would
be lost if not propagated to userland. In fact, this patch results
from the need to rebond with a device lacking persistent storage which
notifies about losing its LTK in ADV_IND reports.
This patch appends the ADV_IND report which triggered the
autoconnection to the EIR Data in the Device Connected event.
Signed-off-by: Alfonso Acosta <fons@spotify.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The values of a lot of the mgmt_device_connected() parameters come
straight from a hci_conn object. We can simplify the function by passing
the full hci_conn pointer to it.
Signed-off-by: Alfonso Acosta <fons@spotify.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If encryption fails and we're using an RPA it may be because of a
conflict with another device. To avoid repeated failures the safest
action is to simply mark the RPA as expired so that a new one gets
generated as soon as the connection drops.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There are several places that need to determine the security level that
an LTK can provide. This patch adds a convenience function for this to
help make the code more readable.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Whether through HCI with BR/EDR or SMP with LE when authentication fails
we should also notify any pending Pair Device mgmt command. This patch
updates the mgmt_auth_failed function to take the actual hci_conn object
and makes sure that any pending pairing command is notified and cleaned
up appropriately.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Wherever we keep hci_conn pointers around we should be using
hci_conn_get/put to ensure that they stay valid. This patch fixes
all places violating against the principle currently.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we get an LE connection complete event there's really no reason to
look through the entire connection parameter list as the entry should be
present in the hdev->pend_le_conns list too. This patch changes the
lookup code to do a more restricted lookup only in the pend_le_conns
list.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In the hci_le_conn_complete_evt() function there's no need to set the
addr_type value until it's actually needed, i.e. for the black list
lookup. This patch moves the code a bit further down in the function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Recently the LE passive scanning and auto-connections feature was
introduced. It uses the hci_connect_le() API which returns a hci_conn
along with a reference count to that object. All previous users would
tie this returned reference to some existing object, such as an L2CAP
channel, and there'd be no leaked references this way. For
auto-connections however the reference was returned but not stored
anywhere, leaving established connections with one higher reference
count than they should have.
Instead of playing special tricks with hci_conn_hold/drop this patch
associates the returned reference from hci_connect_le() with the object
that in practice does own this reference, i.e. the hci_conn_params
struct that caused us to initiate a connection in the first place. Once
the connection is established or fails to establish this reference is
removed appropriately.
One extra thing needed is to call hci_pend_le_actions_clear() before
calling hci_conn_hash_flush() so that the reference is cleared before
the hci_conn objects are fully removed.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we're not connectable and all whitelisted (BR/EDR) devices are
connected it doesn't make sense to keep page scan enabled. This patch
adds code to check for any disconnected whitelist devices and if there
are none take the appropriate action in the hci_update_page_scan()
function to disable page scan.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we're not bondable we should never send any other SSP
authentication requirement besides one of the non-bonding ones.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The HCI_PAIRABLE flag isn't actually controlling whether we're pairable
but whether we're bondable. Therefore, rename it accordingly.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch fixes a typo in the hci_cc_write_scan_enable() function where
we want to clear the HCI_PSCAN flag if the SCAN_PAGE bit of the HCI
command parameter was not set.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When adding remote devices to the kernel using the Add Device management
command, these devices are explicitly allowed to connect. This kind of
incoming connections are possible even when the controller itself is
not connectable.
For BR/EDR this distinction is pretty simple since there is only one
type of incoming connections. With LE this is not that simple anymore
since there are ADV_IND and ADV_DIRECT_IND advertising events.
The ADV_DIRECT_IND advertising events are send for incoming (slave
initiated) connections only. And this is the only thing the kernel
should allow when adding devices using action 0x01. This meaning
of incoming connections is coming from BR/EDR and needs to be
mapped to LE the same way.
Supporting the auto-connection of devices using ADV_IND advertising
events is an important feature as well. However it does not map to
incoming connections. So introduce a new action 0x02 that allows
the kernel to connect to devices using ADV_DIRECT_IND and in addition
ADV_IND advertising reports.
This difference is represented by the new HCI_AUTO_CONN_DIRECT value
for only connecting to ADV_DIRECT_IND. For connection to ADV_IND and
ADV_DIRECT_IND the old value HCI_AUTO_CONN_ALWAYS is used.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Unconditionally connecting to devices sending ADV_DIRECT_IND when
the controller is in CONNECTABLE mode is a feature that is not
fully working. The background scanning trigger for this has been
removed, but the statement allowing it to happen in case some
other part triggers is still present. So remove that code part
as well to avoid unwanted connections.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When we're not pairable we should still allow us to act as initiators
for pairing, i.e. the HCI_PAIRABLE flag should only be affecting
incoming pairing attempts. This patch fixes the relevant checks for the
hci_io_capa_request_evt() and hci_pin_code_request_evt() functions.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Even though our side requests authentication, the original action that
caused it may be remotely triggered, such as an incoming L2CAP or RFCOMM
connect request. To track this information introduce a new hci_conn flag
called HCI_CONN_AUTH_INITIATOR.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When a new hci_conn object is created the remote SSP authentication
requirement is set to the invalid value 0xff to indicate that it is
unknown. Once pairing completes however the code was leaving it as-is.
In case a new pairing happens over the same connection it is important
that we reset the value back to unknown so that the pairing code doesn't
make false assumptions about the requirements.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If user space has a NoInputNoOutput IO capability it makes no sense to
bother it with confirmation requests. This patch updates both SSP and
SMP to check for the local IO capability before sending a user
confirmation request to user space.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Commit 6c53823ae0 reshuffled the way the
authentication requirement gets set in the hci_io_capa_request_evt()
function, but at the same time it failed to update an if-statement where
cp.authentication is used before it has been initialized. The correct
value the code should be looking for in this if-statement is
conn->auth_type.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org # 3.16
We should check the blacklist no matter what, meaning also when we're
not connectable. This patch fixes the respective logic in the function
making the decision whether to accept a connection or not.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we have at least one LE slave connection most (probably all)
controllers will refuse to initiate any new connections. To avoid
unnecessary failures simply check for this situation up-front and skip
the connection attempt.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We need to be able to track slave vs master LE connections in
hci_conn_hash, and to be able to do that we need to know the role of the
connection by the time hci_conn_add_has() is called. This means in
practice the hci_conn_add() call that creates the hci_conn_object.
This patch adds a new role parameter to hci_conn_add() function to give
the object its initial role value, and updates the callers to pass the
appropriate role to it. Since the function now takes care of
initializing both conn->role and conn->out values we can remove some
other unnecessary assignments.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To make the code more understandable it makes sense to use the new HCI
defines for connection role instead of a "bool master" parameter. This
makes it immediately clear when looking at the function calls what the
last parameter is describing.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Having a dedicated u8 role variable in the hci_conn struct greatly
simplifies tracking of the role, since this is the native way that it's
represented on the HCI level.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
All HCI commands and events, including LE ones, use 0x00 for master role
and 0x01 for slave role. It makes therefore sense to add generic defines
for these instead of the current LE_CONN_ROLE_MASTER. Having clean
defines will also make it possible to provide simpler internal APIs.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The check for the blacklist in hci_le_conn_complete_evt() should be when
we know that we have an actual successful connection (ev->status being
non-zero). This patch fixes this ordering.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The params variable was just used for storing the return value from the
hci_pend_le_action_lookup() function and then checking whether it's NULL
or not. We can simplify the code by checking the return value directly.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we need to make the decision whether to perform just-works or real
user confirmation we need to know the exact local authentication
requirement that was passed to the controller. So far conn->auth_type
(the local requirement) wasn't in one case updated appropriately in fear
of the user confirmation being rejected later.
The real problem however was not really that conn->auth_type couldn't
represent the true value but that we were checking the local MITM
requirement in an incorrect way. It's perfectly fine to let auth_type
follow what we tell the controller since we're still tracking the target
security level with conn->pending_sec_level.
This patch updates the check for local MITM requirement in the
hci_user_confirm_request_evt function to use the locally requested
security level and ensures that auth_type always represents what we tell
the controller. All other code in hci_user_confirm_request_evt still
uses the auth_type instead of pending_sec_level for determining whether
to do just-works or not, since that's the only value that's in sync with
what the remote device knows.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Tested-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org # 3.16
The internals of the HCI request framework should not be leaking to
its users. Move them all into net/bluetooth/hci_core.c and provide
a simple hci_req_pending helper function for the one user outside
the framework.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Set Connectable/Discoverable mgmt handlers use a hci_request with a
proper callback to handle the HCI command sending. It makes therefore
little sense to have this extra function to be called from hci_event.c
for command failures.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since the HCISETSCAN ioctl is the only non-mgmt user we care about for
setting the right discoverable state we can simply do the necessary
updates in the ioctl handler function instead. This then allows the
removal of the mgmt_discoverable function and should simplify that state
handling considerably.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The mgmt_connectable function has been used to ensure that the right
actions to HCI_CONNECTABLE are taken when the HCI_Write_Scan_Enable
command is triggered by something else than mgmt. The only other user
that we really care about is the HCISETSCAN ioctl code, so we can
actually more simply perform the needed changes there instead.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for looking up entries in the white list when
HCI_CONNECTABLE is not set. The logic is fairly simple: if we're
connectable check the black list, if we're not connectable check the
white list.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The conditions for accepting an incoming connections are already
non-trivial and will become more so once a white list is added. This
patch breaks up the checks for when to reject the request by creating a
helper function for it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We already have several lists with struct bdaddr_list entries, and there
will be more in the future. Since the operations for adding, removing,
looking up and clearing entries in these lists are exactly the same it
doesn't make sense to define new functions for every single list. This
patch unifies the functions by passing the list_head to them instead of
a hci_dev pointer.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
All LE controllers always implicitly stop advertising when establishing
connections. Therefore, be sure to clear the flag in the event handler
for new LE connections.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There are many different places that can disable LE scanning but we only
want to re-enable advertising in hci_cc_le_set_scan_enable() for a very
specific use case, which is when the active scanning part of Start
Discovery is complete. Because of this, fix the discovery state check to
test for the exact state.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Many controllers allow simultaneous active scanning and advertising
(e.g. Intel and Broadcom) but some do not (e.g. CSR). It's therefore
safest to implement mutual exclusion of these states in the kernel.
This patch ensures that the two states are never entered simultaneously.
Extra precaution needs to be taken for outgoing connection attempts in
slave role (i.e. through directed advertising) in which case the
operation that came first has precedence and the one that comes after
gets a rejection.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since the real advertising state is now tracked with its own flag we can
simply set/unset the HCI_ADVERTISING flag in the
set_advertising_complete function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Having a single HCI_ADVERTISING flag is problematic since it tries to
track both the real advertising state and the corresponding mgmt
setting. To make the logic simpler and more reliable add a new flag that
only tracks the actual advertising state that has been written to the
controller.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If we have both LE scanning and advertising simultaneously enabled we
need a way to tell hci_connect_le() in which role to initiate a
connection. This patch adds a new parameter to the function to give it
the necessary information. For auto-connect and mgmt_pair_device we
always use master role, whereas for L2CAP users (in practice sockets) we
use slave role whenever HCI_ADVERTISING is set and master role
otherwise.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The auth_type value which gets assigned to hci_conn->auth_type is
something that's only used for BR/EDR connections and is of no value for
LE connections. It makes therefore little sense to pass it to the
hci_connect_le() function. This patch removes the parameter from the
function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since the only caller of this function doesn't care about the return
value anymore let's just remove it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If we have devices set as to be connected we should connect to them even
during normal discovery if we get a connectable advertising event. If we
also have HCI_CONNECTABLE set we should connect ADV_DIRECT_IND events
even to devices that we don't have in our pend_le_conns list. This patch
implements such behavior by passing the advertising report type to
check_pending_le_conn() and calls that function regardless of what type
of scanning we are doing.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we get an LE connection complete event we should restart background
scanning if there are any devices needing it. So far the code was only
making the decision based on whether the completed connection had any
stored parameters or not. This patch ensures that we trigger background
scanning always when necessary.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we establish connections as a consequence of receiving an
advertising report it makes no sense to wait the normal 20 second LE
connection timeout. This patch modifies the hci_connect_le function to
take an extra timeout value and uses a lower 2 second timeout for the
auto-connection case. This timeout is intentionally chosen to be just a
bit higher than the 1.28 second timeout that High Duty Cycle Advertising
uses.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
During the setup phase of a controller, the Bluetooth address will be
read and to have that original address available for later use, store
it as setup address.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The HCI event callbacks have grown over the last years and some
functions handle status checking different than others. For the
simple ones, check the status at the beginning and exit if an
error with the HCI command occured.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If a found device is marked as blocked while doing passive LE scanning,
neither report it nor try to connect to it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Instead of looking through the entire list of entries we can more
efficiently use the new hci_pend_le_action_lookup() function to look up
entries specifically in the pend_le_reports list. Since the search is
now limited to the right list we can also remove an unnecessary check
for list_empty() before the lookup.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In some circumstances we need to look up entries in pend_le_conns and in
other in pend_le_reports. This patch converts the existing lookup
function for pend_le_conns to something that can be used for both lists.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This is the last place using hci_pend_le_conn_add() and we can more
just as simply manipulate the list directly here.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since params->action is used for both the pend_le_conns and
pend_le_reports lists we can simplify the adding and deleting of the
lists considerably. For example, when deleting entries in most
situations we no-longer need to check the auto_connect value but can
directly proceed with calling list_del_init on param->action (which is
safe even if the entry is not part of any list).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To simplify manipulation and lookup of hci_conn_params entries of the
type HCI_AUTO_CONN_REPORT it makes sense to store them in their own
list. The new action list_head in hci_conn_params is used for this
purpose.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If we're doing passive scanning we shouldn't proceed with any of the
code that deals with active scanning (pending reports, etc.). This patch
fixes a missing return statement for the passive scanning section in the
process_adv_report() function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since we only store entries with identity addresses in the
le_conn_params and pend_le_conns lists we can avoid unnecessary lookups
by checking for an identity address before diving into the lists
themselves.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If a device is in the pend_le_conns list it cannot at the same time also
have the need to be notified through mgmt_device_found. By making
check_pending_le_conn return whether it found an entry or not we can
avoid unnecessary checks in process_adv_report().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since the connection parameters are always a basis for adding entries to
hdev->pend_le_conns (so far of type bdaddr_list) it's simpler and more
efficient to have the parameters themselves be the entries in the
pend_le_conns list. We do this by adding another list_head to the
hci_conn_params struct.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When processing passive scanning results we need the resolved identity
address both in check_pending_le_conn() as well as later in
process_adv_report(). Since process_adv_report() calls
check_pending_le_conn() we can simply resolve the IRK earlier in the
function and thereby eliminate a second lookup.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we're scanning for specific devices that use an RPA we need to
convert the RPA to the identity address before looking up the entry in
the connection parameters. This patch adds the necessary code to do this
in the process_adv_report() function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If we have one or more devices with HCI_AUTO_CONN_REPORT we should do
background scanning and emit mgmt_device_found events. This patch
modifies the hci_update_background_scan() function to extend the
conditions needed to trigger scanning, and adds the necessary code to
process_adv_report() to emit mgmt_device_found events.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The calling functions of mgmt_new_conn_param have more information about
the parameters, such as whether the kernel is tracking them or not. It
makes therefore sense to have them pass an initial store_hint value to
the mgmt_new_conn_param function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We should update any stored connection parameters when we receive the LE
Remote Connection Parameter Request HCI event. This patch adds the
necessary code to the function that handles the event.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Unlike BR/EDR we cannot reject LE connections of blocked devices but
have to do it as soon as we get a LE Connection Complete event. The
patch adds a blacklist check to the hci_le_conn_complete_evt function
and drops all connections for blocked devices.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduces a new Mgmt event called "New Connection Parameter".
This event indicates to userspace the connection parameters values the
remote device requested.
The user may store these values and load them into kernel. This way, next
time a connection is established to that device, the kernel will use those
parameters values instead of the default ones.
This event is sent when the remote device requests new connection
parameters through connection parameter update procedure. This event is
not sent for slave connections.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for LE Connection Parameters Request Link
Layer control procedure introduced in Core spec 4.1. This procedure
allows a Peripheral or Central to update the Link Layer connection
parameters of an established connection.
Regarding the acceptance of connection parameters, the LL procedure
follows the same approach of L2CAP procedure (see l2cap_conn_param_
update_req function). We accept any connection parameters values as
long as they are within the valid range.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There are certain subtle differences in behavior when we're encrypted
with the STK, such as allowing re-encryption even though the security
level stays the same. Because of this, add a flag to track whether we're
encrypted with an STK or not.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Device Found events of the management interface should indicate if
it is possible to connect to a remote device or if it is broadcaster
only advertising. To allow this differentation the Not Connectable flag
is introduced that will be set when it is known that a device can not
be connected.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Providing the flags parameter directly to mgmt_device_found function
makes the core simpler and more readable. With this it becomes a lot
easier to add new flags in the future.
This also changes hci_inquiry_cache_update to just return that flags
needed for mgmt_device_found since that is its only use for the two
return parameters anyway.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The advertising data and scan response data are merged in the wrong
order. It should be advertsing data first and then scan response data
and not the other way around.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org # 3.16
This is to support the Motorola HF850 carkit which reports the error
code 0x10 for an eSCO attempt, even though it advertises eSCO support.
With this patch we will retry with a SCO connection, which succeeds.
Signed-off-by: Nick Pelly <npelly@google.com>
Signed-off-by: Kiran Kumar Raparthy <kiran.kumar@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for storing the local and piconet clock values
from the HCI_Read_Clock command response to the hci_dev and hci_conn
structs. This will be later used in another patch to implement support
for the Get Clock Info mgmt command.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since the link_mode member of the hci_conn struct is a bit field and we
already have a flags member as well it makes sense to merge these two
together. This patch moves all used link_mode bits into corresponding
flags. To keep backwards compatibility with user space we still need to
provide a get_link_mode() helper function for the ioctl's that expect a
link_mode style value.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There's no point in having boolean variables in the hci_conn struct
since it already has a flags member. This patch converts the flush_key
member into a proper flag.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Instead of waiting for a disconnection to occur to remove a debug key
simply never store it in the list to begin with. This means we can also
remove the debug keys check when looking up keys in
hci_link_key_request_evt().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We're planning to add a flag to actively use debug keys in addition to
simply just accepting them, which makes the current generically named
DEBUG_KEYS flag a bit confusing. Since the flag in practice affects
whether the kernel keeps debug keys around or not rename it to
HCI_KEEP_DEBUG_KEYS.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There are two callers of hci_add_link_key(). The first one is the HCI
Link Key Notification event and the second one the mgmt code that
receives a list of link keys from user space. Previously we've had the
hci_add_link_key() function being responsible for also emitting a mgmt
signal but for the latter use case this should not happen. Because of
this a rather awkward new_key paramter has been passed to the function.
This patch moves the mgmt event sending out from the hci_add_link_key()
function, thereby making the code a bit more understandable.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For all incoming LE connections, the minimum and maximum connection
interval is a value that should be copied from the controller default
values. This allows to properly check if the resulting connection
interval of a newly established connection is in the range we are
expecting.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the LE controller changes its connection parameters, it will send
a connection parameter update event. Make sure that the new set of
parameters are stored in hci_conn struct and thus will properly update
the previous values retrieved from the connection complete event.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The LE connection parameters are needed later on to be able to decide
if it is required to trigger connection update procedures. So when the
connection has been established successfully, store the current used
parameters in hci_conn struct.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Create a CoC dynamically instead of one fixed channel for communication
to peer devices.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The LTK type has really nothing to do with HCI so it makes more sense to
have these in smp.h than hci.h. This patch moves the defines to smp.h
and removes the HCI_ prefix in the same go.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We never store the "master" type of STKs since we request encryption
directly with them so we only need one STK type (the one that's
looked-up on the slave side). Simply remove the unnecessary define and
rename the _SLAVE one to the shorter form.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since the whole HCI command, event and data packet processing has been
migrated to use workqueues instead of tasklets, it makes sense to use
struct delayed_work instead of struct timer_list for the timeout
handling. This patch converts the hdev->cmd_timer to use workqueue
as well.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When inquiry is canceled through the HCI_Cancel_Inquiry command there is
no Inquiry Complete event generated. Instead, all we get is the command
complete for the HCI_Inquiry_Cancel command. This means that we must
call the hci_discovery_set_state() function from the respective command
complete handler in order to ensure that user space knows the correct
discovery state.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
When responding to an IO capability request when we're the initiators of
the pairing we will not yet have the remote IO capability information.
Since the conn->auth_type variable is treated as an "absolute"
requirement instead of a hint of what's needed later in the user
confirmation request handler it's important that it doesn't have the
MITM bit set if there's any chance that the remote device doesn't have
the necessary IO capabilities.
This patch adds a clarifying comment so that conn->auth_type is left
untouched in this scenario.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
From the Bluetooth Core Specification 4.1 page 1958:
"if both devices have set the Authentication_Requirements parameter to
one of the MITM Protection Not Required options, authentication stage 1
shall function as if both devices set their IO capabilities to
DisplayOnly (e.g., Numeric comparison with automatic confirmation on
both devices)"
So far our implementation has done user confirmation for all just-works
cases regardless of the MITM requirements, however following the
specification to the word means that we should not be doing confirmation
when neither side has the MITM flag set.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Tested-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
Pull networking updates from David Miller:
1) Seccomp BPF filters can now be JIT'd, from Alexei Starovoitov.
2) Multiqueue support in xen-netback and xen-netfront, from Andrew J
Benniston.
3) Allow tweaking of aggregation settings in cdc_ncm driver, from Bjørn
Mork.
4) BPF now has a "random" opcode, from Chema Gonzalez.
5) Add more BPF documentation and improve test framework, from Daniel
Borkmann.
6) Support TCP fastopen over ipv6, from Daniel Lee.
7) Add software TSO helper functions and use them to support software
TSO in mvneta and mv643xx_eth drivers. From Ezequiel Garcia.
8) Support software TSO in fec driver too, from Nimrod Andy.
9) Add Broadcom SYSTEMPORT driver, from Florian Fainelli.
10) Handle broadcasts more gracefully over macvlan when there are large
numbers of interfaces configured, from Herbert Xu.
11) Allow more control over fwmark used for non-socket based responses,
from Lorenzo Colitti.
12) Do TCP congestion window limiting based upon measurements, from Neal
Cardwell.
13) Support busy polling in SCTP, from Neal Horman.
14) Allow RSS key to be configured via ethtool, from Venkata Duvvuru.
15) Bridge promisc mode handling improvements from Vlad Yasevich.
16) Don't use inetpeer entries to implement ID generation any more, it
performs poorly, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1522 commits)
rtnetlink: fix userspace API breakage for iproute2 < v3.9.0
tcp: fixing TLP's FIN recovery
net: fec: Add software TSO support
net: fec: Add Scatter/gather support
net: fec: Increase buffer descriptor entry number
net: fec: Factorize feature setting
net: fec: Enable IP header hardware checksum
net: fec: Factorize the .xmit transmit function
bridge: fix compile error when compiling without IPv6 support
bridge: fix smatch warning / potential null pointer dereference
via-rhine: fix full-duplex with autoneg disable
bnx2x: Enlarge the dorq threshold for VFs
bnx2x: Check for UNDI in uncommon branch
bnx2x: Fix 1G-baseT link
bnx2x: Fix link for KR with swapped polarity lane
sctp: Fix sk_ack_backlog wrap-around problem
net/core: Add VF link state control policy
net/fsl: xgmac_mdio is dependent on OF_MDIO
net/fsl: Make xgmac_mdio read error message useful
net_sched: drr: warn when qdisc is not work conserving
...
When checking whether a legacy link key provides at least HIGH security
level we also need to check for FIPS level which is one step above HIGH.
This patch fixes a missing check in the hci_link_key_request_evt()
function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
When checking whether we need to request authentication or not we should
include HCI_SECURITY_FIPS to the levels that always need authentication.
This patch fixes check for it in the hci_outgoing_auth_needed()
function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
This patch adds support to store local maximum TX power level for
connection when reply for HCI_Read_Transmit_Power_Level is received.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support to store local TX power level for connection
when reply for HCI_Read_Transmit_Power_Level is received.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support to store RSSI for connection when reply for
HCI_Read_RSSI is received.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Commit 1c2e004183 introduced an event handler for the encryption key
refresh complete event with the intent of fixing some LE/SMP cases.
However, this event is shared with BR/EDR and there we actually want to
act only on the auth_complete event (which comes after the key refresh).
If we do not do this we may trigger an L2CAP Connect Request too early
and cause the remote side to return a security block error.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
The GAP Specification gives the flexibility to decide whether MITM
Protection is requested or not (Bluetooth Core Specification v4.0
Volume 3, part C, section 6.5.3) when replying to an
HCI_EV_IO_CAPA_REQUEST event.
The recommendation is *not* to set this flag "unless the security
policy of an available local service requires MITM Protection"
(regardless of the bonding type). However, the kernel doesn't
necessarily have this information and therefore the safest choice is
to always use MITM Protection, also for General Bonding.
This patch changes the behavior for the General Bonding initiator
role, always requesting MITM Protection even if no high security level
is used. Depending on the remote capabilities, the protection might
not be actually used, and we will accept this locally unless of course
a high security level was originally required.
Note that this was already done for Dedicated Bonding. No-Bonding is
left unmodified because MITM Protection is normally not desired in
these cases.
Signed-off-by: Mikel Astiz <mikel.astiz@bmw-carit.de>
Signed-off-by: Timo Mueller <timo.mueller@bmw-carit.de>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When responding to a remotely-initiated pairing procedure, a MITM
protected SSP associaton model can be used for pairing if both local
and remote IO capabilities are set to something other than
NoInputNoOutput, regardless of the bonding type (Dedicated or
General).
This was already done for Dedicated Bonding but this patch proposes to
use the same policy for General Bonding as well.
The GAP Specification gives the flexibility to decide whether MITM
Protection is used ot not (Bluetooth Core Specification v4.0 Volume 3,
part C, section 6.5.3).
Note however that the recommendation is *not* to set this flag "unless
the security policy of an available local service requires MITM
Protection" (for both Dedicated and General Bonding). However, as we are
already requiring MITM for Dedicated Bonding, we will follow this
behaviour also for General Bonding.
Signed-off-by: Timo Mueller <timo.mueller@bmw-carit.de>
Signed-off-by: Mikel Astiz <mikel.astiz@bmw-carit.de>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Do not always set the MITM protection requirement by default in the
field conn->auth_type, since this will be added later in
hci_io_capa_request_evt(), as part of the requirements specified in
HCI_OP_IO_CAPABILITY_REPLY.
This avoids a hackish exception for the auto-reject case, but doesn't
change the behavior of the code at all.
Signed-off-by: Mikel Astiz <mikel.astiz@bmw-carit.de>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Refactor the code without changing its behavior by handling the
no-bonding cases first followed by General Bonding.
Signed-off-by: Mikel Astiz <mikel.astiz@bmw-carit.de>
Signed-off-by: Timo Mueller <timo.mueller@bmw-carit.de>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When sending out a device found event caused by an advertising report in
the situation where we couldn't store the report as a pending one, the
code was incorrectly trying to use the address and address type from the
pending data. Since the pending data is cleared in the previous line
this causes a potentially incorrect address type and an address of
BDADDR_ANY. This patch fixes the call to use the address information
correctly from the received advertising report.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When sending a pending device found event triggered by disabling LE
scanning we should use the stored RSSI instead of sending a zero value.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Especially in crowded environments it can become frequent that we have
to send out whatever pending event there is stored. Since user space
has its own filtering of small RSSI changes sending a 0 value will
essentially force user space to wake up the higher layers (e.g. over
D-Bus) even though the RSSI didn't actually change more than the
threshold value.
This patch adds storing also of the RSSI for pending advertising reports
so that we report an as accurate RSSI as possible when we have to send
out the stored information to user space.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Occasionally, during active scanning we will receive duplicate ADV_IND
reports from the same device before receiving the SCAN_RSP from them. In
order to not wake up user space unnecessarily it's better not to send
these extra events as they do not contain any new information.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To avoid too many events being sent to user space and to help parsing of
all available remote device data it makes sense for us to wait for the
scan response and send a single merged Device Found event to user space.
This patch adds a few new variables to hci_dev to track the last
received ADV_IND/ADV_SCAN_IND, i.e. those which will cause a SCAN_REQ to
be send in the case of active scanning. When the SCAN_RSP is received
the pending data is passed together with the SCAN_RSP to the
mgmt_device_found function which takes care of merging them into a
single Device Found event.
We also need a bit of extra logic to handle situations where we don't
receive a SCAN_RSP after caching some data. In such a scenario we simply
have to send out the pending data as it is and then operate on the new
report as if there was no pending data.
We also need to send out any pending data when scanning stops as
well as ensure that the storage is empty at the start of a new active
scanning session. These both cases are covered by the update to the
hci_cc_le_set_scan_enable function in this patch.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we're in peripheral mode (HCI_ADVERTISING flag is set) the most
natural mapping of connect() is to perform directed advertising to the
peer device.
This patch does the necessary changes to enable directed advertising and
keeps the hci_conn state as BT_CONNECT in a similar way as is done for
central or BR/EDR connection initiation.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In preparation for being able to merge ADV_IND/ADV_SCAN_IND and SCAN_RSP
together into a single device found event add a second parameter to the
mgmt_device_found function. For now all callers pass NULL as this
parameters since we don't yet have storing of the last received
advertising report.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Passive LE scanning is only used by the kernel-internal connection
establishment procedure. It makes therefore little sense to send device
found events to user space.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Once directed advertising is brought into the picture simply the lack of
an hci_conn object when an le_conn_complete event occurs is no longer a
reliable indication that the responder & initiator values need to be
set based on our advertising address type.
This patch moves the code for setting these values outside of the
"if (!conn)" branch and ensures that they get set for any connection
where we are in the slave role.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Any time hci_conn_add is used for an LE connection we need to ensure
that the local identity address is correctly described in the src and
src_type variables. This patch moves setting these values directly into
hci_conn_add so that callers don't have to duplicate the effort
themselves.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
As preparation for merging ADV_IND/ADV_SCAN_IND and SCAN_RSP together
into a single mgmt Device Found event refactor individual advertising
report handling into a separate function. This will help keep the code
more readable as more logic gets added.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
It is possible that the HCI_LE_Start_Encryption command fails in an
early stage and triggers a command status event with the failure code.
In such a case we need to properly notify the hci_conn object and
cleanly bring the connection down. This patch adds the missing command
status handler for this HCI command.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The LE scan type paramter defines if active scanning or passive scanning
is in use. Track the currently set value so it can be used for decision
making from other pieces in the core.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The passkey_notify and user_confirm functions in mgmt.c were expecting
different endianess for the passkey, leading to a big endian bug and
sparse warning in recently added SMP code. This patch converts both
functions to expect host endianess and do the conversion to little
endian only when assigning to the mgmt event struct.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In Secure Connections Only mode, it is required that Secure Connections
is used for pairing and that the link key is encrypted with AES-CCM using
a P-256 authenticated combination key. If this is not the case, then new
connection shall be refused or existing connections shall be dropped.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The use of __constant_<foo> has been unnecessary for quite awhile now.
Make these uses consistent with the rest of the kernel.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch fixes authentication failure on LE link re-connection when
BlueZ acts as slave (peripheral). LTK is removed from the internal list
after its first use causing PIN or Key missing reply when re-connecting
the link. The LE Long Term Key Request event indicates that the master
is attempting to encrypt or re-encrypt the link.
Pre-condition: BlueZ host paired and running as slave.
How to reproduce(master):
1) Establish an ACL LE encrypted link
2) Disconnect the link
3) Try to re-establish the ACL LE encrypted link (fails)
> HCI Event: LE Meta Event (0x3e) plen 19
LE Connection Complete (0x01)
Status: Success (0x00)
Handle: 64
Role: Slave (0x01)
...
@ Device Connected: 00:02:72:DC:29:C9 (1) flags 0x0000
> HCI Event: LE Meta Event (0x3e) plen 13
LE Long Term Key Request (0x05)
Handle: 64
Random number: 875be18439d9aa37
Encryption diversifier: 0x76ed
< HCI Command: LE Long Term Key Request Reply (0x08|0x001a) plen 18
Handle: 64
Long term key: 2aa531db2fce9f00a0569c7d23d17409
> HCI Event: Command Complete (0x0e) plen 6
LE Long Term Key Request Reply (0x08|0x001a) ncmd 1
Status: Success (0x00)
Handle: 64
> HCI Event: Encryption Change (0x08) plen 4
Status: Success (0x00)
Handle: 64
Encryption: Enabled with AES-CCM (0x01)
...
@ Device Disconnected: 00:02:72:DC:29:C9 (1) reason 3
< HCI Command: LE Set Advertise Enable (0x08|0x000a) plen 1
Advertising: Enabled (0x01)
> HCI Event: Command Complete (0x0e) plen 4
LE Set Advertise Enable (0x08|0x000a) ncmd 1
Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 19
LE Connection Complete (0x01)
Status: Success (0x00)
Handle: 64
Role: Slave (0x01)
...
@ Device Connected: 00:02:72:DC:29:C9 (1) flags 0x0000
> HCI Event: LE Meta Event (0x3e) plen 13
LE Long Term Key Request (0x05)
Handle: 64
Random number: 875be18439d9aa37
Encryption diversifier: 0x76ed
< HCI Command: LE Long Term Key Request Neg Reply (0x08|0x001b) plen 2
Handle: 64
> HCI Event: Command Complete (0x0e) plen 6
LE Long Term Key Request Neg Reply (0x08|0x001b) ncmd 1
Status: Success (0x00)
Handle: 64
> HCI Event: Disconnect Complete (0x05) plen 4
Status: Success (0x00)
Handle: 64
Reason: Authentication Failure (0x05)
@ Device Disconnected: 00:02:72:DC:29:C9 (1) reason 0
Signed-off-by: Claudio Takahasi <claudio.takahasi@openbossa.org>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The stop_scan_complete function was used as an intermediate step before
doing the actual connection creation. Since we're using hci_request
there's no reason to have this extra function around, i.e. we can simply
put both HCI commands into the same request.
The single task that the intermediate function had, i.e. indicating
discovery as stopped is now taken care of by a new
HCI_LE_SCAN_INTERRUPTED flag which allows us to do the discovery state
update when the stop scan command completes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The discovery process has a timer for disabling scanning, however
scanning might be disabled through other means too like the auto-connect
process. We should therefore ensure that the timer is never active
after sending a HCI command to disable scanning.
There was some existing code in stop_scan_complete trying to avoid the
timer when a connect request interrupts a discovery procedure, but the
other way around was not covered. This patch covers both scenarios by
canceling the timer as soon as we get a successful command complete for
the disabling HCI command.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
LE connection attempts do not have a controller side timeout in the same
way as BR/EDR has (in form of the page timeout). Since we always do
scanning before initiating connections the attempts are always expected
to succeed in some reasonable time.
This patch adds a timer which forces a cancellation of the connection
attempt within 20 seconds if it has not been successful by then. This
way we e.g. ensure that mgmt_pair_device times out eventually and gives
an error response.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
