It seems there is an alternate version of the hardware with a different
PID. User testing reveals this still works with the same interface as far
as the kernel is concerned, so just add the extra PID. Thanks to Heiko
Engemann for testing with this version.
Due to the way quirks-table.h is structured, that means we have to turn
the entire quirk struct into a macro to avoid duplicating it...
Cc: stable@vger.kernel.org
Signed-off-by: Asahi Lina <lina@asahilina.net>
Link: https://patch.msgid.link/20241202-rme-digiface-usb-id-v1-1-50f730d7a46e@asahilina.net
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The WD19 family of docks has the same audio chipset as the WD15. This
change enables jack detection on the WD19.
We don't need the dell_dock_mixer_init quirk for the WD19. It is only
needed because of the dell_alc4020_map quirk for the WD15 in
mixer_maps.c, which disables the volume controls. Even for the WD15,
this quirk was apparently only needed when the dock firmware was not
updated.
Signed-off-by: Jan Schär <jan@jschaer.ch>
Cc: <stable@vger.kernel.org>
Link: https://patch.msgid.link/20241029221249.15661-1-jan@jschaer.ch
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This also includes a change to the capture level as they differ with
this device, as well as additional values for prefader channels.
Acked-by: Olivia Mackintosh <livvy@base.nu>
Signed-off-by: Sarah Grant <s@srd.tw>
Link: https://patch.msgid.link/20241025163927.12662-1-s@srd.tw
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Implement sync, output format, and input status mixer controls, to allow
the interface to be used as a straight ADAT/SPDIF (+ Headphones) I/O
interface.
This does not implement the matrix mixer, output gain controls, or input
level meter feedback. The full mixer interface is only really usable
using a dedicated userspace control app (there are too many mixer nodes
for alsamixer to be usable), so for now we leave it up to userspace to
directly control these features using raw USB control messages. This is
similar to how it's done with some FireWire interfaces (ffado-mixer).
Signed-off-by: Asahi Lina <lina@asahilina.net>
Link: https://patch.msgid.link/20240903-rme-digiface-v2-2-71b06c912e97@asahilina.net
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Registering Numark Party Mix II fails with error 'bogus bTerminalLink 1'.
The problem stems from the driver not being able to find input/output
terminals required to configure audio streaming. The information about
those terminals is stored in AudioControl Interface. Numark device
contains 2 AudioControl Interfaces and the driver checks only one of them.
According to the USB standard, a device can have multiple audio functions,
each represented by Audio Interface Collection. Every audio function is
considered to be closed box and will contain unique AudioControl Interface
and zero or more AudioStreaming and MIDIStreaming Interfaces.
The Numark device adheres to the standard and defines two audio functions:
- MIDIStreaming function
- AudioStreaming function
It starts with MIDI function, followed by the audio function. The driver
saves the first AudioControl Interface in `snd_usb_audio` structure
associated with the entire device. It then attempts to use this interface
to query for terminals and clocks. However, this fails because the correct
information is stored in the second AudioControl Interface, defined in the
second Audio Interface Collection.
This patch introduces a structure holding association between each
MIDI/Audio Interface and its corresponding AudioControl Interface,
instead of relying on AudioControl Interface defined for the entire
device. This structure is populated during usb probing phase and leveraged
later when querying for terminals and when sending USB requests.
Alternative solutions considered include:
- defining a quirk for Numark where the order of interface is manually
changed, or terminals are hardcoded in the driver. This solution would
have fixed only this model, though it seems that device is USB compliant,
and it also seems that other devices from this company may be affected.
What's more, it looks like products from other manufacturers have similar
problems, i.e. Rane One DJ console
- keeping a list of all AudioControl Interfaces and querying all of them
to find required information. That would have solved my problem and have
low probability of breaking other devices, as we would always start with
the same logic of querying first AudioControl Interface. This solution
would not have followed the standard though.
This patch preserves the `snd_usb_audio.ctrl_intf` variable, which holds
the first AudioControl Interface, and uses it as a fallback when some
interfaces are not parsed correctly and lack an associated AudioControl
Interface, i.e., when configured via quirks.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217865
Signed-off-by: Karol Kosik <k.kosik@outlook.com>
Link: https://patch.msgid.link/AS8P190MB1285893F4735C8B32AD3886BEC852@AS8P190MB1285.EURP190.PROD.OUTLOOK.COM
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add missing input gain and master output mixer controls for
RME Babyface Pro.
This patch implements:
1. Input gain controls for 2 mic and 2 line inputs
2. Master output volume controls for all 12 output channels
These additions allow for more complete control of the Babyface Pro under
Linux.
Signed-off-by: Stefan Stistrup <sstistrup@gmail.com>
Link: https://patch.msgid.link/20240809204922.20112-1-sstistrup@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of the explicit "1 << x", use BIT() macro for one bit values.
This will improve the readability and also avoids the possible bad
value for 31bit shift.
Link: https://patch.msgid.link/20240715123646.26679-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add Focusrite Vocaster One and Two USB IDs, notification arrays,
config sets, and device info data.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <5fb48555a8db7bb322b25784b165829357cd6e42.1710264833.git.g@b4.vu>
These values mirror those of the Pioneer DJM-250MK2 as the channel layout
appears identical based on my observations. This duplication could be removed in
later contributions if desired.
Signed-off-by: Sarah Grant <s@srd.tw>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231201181654.5058-1-s@srd.tw
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This driver was originally developed for the Focusrite Scarlett Gen 2
series. Since then Focusrite have used a similar protocol for their
Gen 3, Gen 4, Clarett USB, Clarett+, and Vocaster series.
Let's call this common protocol the "Scarlett 2 Protocol" and rename
the driver to scarlett2 to not imply that it is restricted to Gen 2
series devices.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/e1ad7f69a1e20cdb39094164504389160c1a0a0b.1698342632.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It has been confirmed that all devices in the Focusrite Clarett USB
series work the same as the devices in the Clarett+ series. Add the
missing PIDs to enable support for the Clarett 2Pre and 4Pre USB.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/ZSFB8EVTG1PK1eq/@m.b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Focusrite Clarett+ series uses the same protocol as the Scarlett
Gen 2 and Gen 3 series. This patch adds support for the Clarett+ 2Pre
and Clarett+ 4Pre similarly to the existing 8Pre support by adding
appropriate entries to the scarlett2 driver.
The Clarett 2Pre USB and 4Pre USB presumably use the same protocol as
well, so support for them can easily be added if someone can test.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/ZRL7qjC3tYQllT3H@m.b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Focusrite Clarett+ 8Pre uses the same protocol as the Scarlett Gen
2 and Gen 3 product range. This patch adds support for the Clarett+
8Pre by adding appropriate entries to the scarlett2 driver.
The Clarett+ 2Pre and 4Pre, and the Clarett USB product line
presumably use the same protocol as well, so support for them can
easily be added if someone can test.
Signed-off-by: Christian Colglazier <christian@cacolglazier.com>
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/20220809043241.GA2749152@m.b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This removes the need to power cycle the Dell WD15 dock if it has been
attached to a Windows machine.
The Windows driver puts the ALC4020 USB audio controller into
'manual mode', and then does all the power management and other
configuration itself, by sending HD audio commands directly to the
ALC3263 audio codec via vendor-type USB messages. If manual mode is off,
this is all handled by the firmware, and works well enough.
If manual mode is turned on, the latency of the SET INTERFACE command
goes from several hundred ms to less than 1 ms
(see https://bugzilla.suse.com/show_bug.cgi?id=1089467), but I'm not
sure if the additional code that would be required is worth it.
Funnily enough, the Windows driver tries to turn off manual mode when
the dock is disconnected, which doesn't work for obvious reasons.
Additionally, fix a bug in dell_dock_init_vol, which didn't work because
the Control Selector was missing.
Now, it properly resets the volume to 0dB.
Fixes: 964af639ad ("ALSA: usb-audio: Initialize Dell Dock playback volumes")
Signed-off-by: Jan Schär <jan@jschaer.ch>
Link: https://lore.kernel.org/r/20220627171855.42338-2-jan@jschaer.ch
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Dell WD15 dock has a headset and a line out port. Add support for
detecting if a jack is inserted into one of these ports.
For the headset jack, additionally determine if a mic is present.
The WD15 contains an ALC4020 USB audio controller and ALC3263 audio codec
from Realtek. It is a UAC 1 device, and UAC 1 does not support jack
detection. Instead, jack detection works by sending HD Audio commands over
vendor-type USB messages.
I found out how it works by looking at USB captures on Windows.
The audio codec is very similar to the one supported by
sound/soc/codecs/rt298.c / rt298.h, some constant names and the mic
detection are adapted from there. The realtek_add_jack function is adapted
from build_connector_control in sound/usb/mixer.c.
I tested this on a WD15 dock with the latest firmware.
Signed-off-by: Jan Schär <jan@jschaer.ch>
Link: https://lore.kernel.org/r/20220627171855.42338-1-jan@jschaer.ch
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For the RODE NT-USB the lowest Playback mixer volume setting mutes the
audio output. But it is not reported as such causing e.g. PulseAudio to
accidentally mute the device when selecting a low volume.
Fix this by applying the existing quirk for this kind of issue when the
device is detected.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220311201400.235892-1-lars@metafoo.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Olivia Mackintosh has posted to alsa-devel reporting that
there's a potential bug that could break mixer quirks for Pioneer
devices introduced by 6d27788160
"ALSA: usb-audio: Add support for the Pioneer DJM 750MK2
Mixer/Soundcard".
This happened because the DJM 750 MK2 was added last to the Pioneer DJM
device table index and defined as 0x4 but was added to snd_djm_devices[]
just after the DJM 750 (MK1) entry instead of last, after the DJM 900
NXS2. This escaped review.
To prevent that from ever happening again, Takashi Iwai suggested to use
C99 array designators in snd_djm_devices[] instead of simply reordering
the entries.
Fixes: 6d27788160 ("ALSA: usb-audio: Add support for the Pioneer DJM 750MK2")
Reported-by: Olivia Mackintosh <livvy@base.nu>
Suggested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Geraldo Nascimento <geraldogabriel@gmail.com>
Link: https://lore.kernel.org/r/Yau46FDzoql0SNnW@geday
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The kernel already has support for very similar Pioneer djm products
and this work is based on that.
Added device to quirks-table.h and added control info to
mixer_quirks.c.
Tested on my hardware and all working.
Signed-off-by: William Overton <willovertonuk@gmail.com>
Link: https://lore.kernel.org/r/20211010145841.11907-1-willovertonuk@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
USB-audio driver assumes that the normal resume would preserve the
device configuration while reset_resume wouldn't, and tries to restore
the mixer elements only at reset_resume callback. However, this seems
too naive, and some devices do behave differently, resetting the
volume at the normal resume; this resulted in the inconsistent volume
that surprised users.
This patch changes the mixer resume code to handle both the normal and
reset resume in the same way, always restoring the original mixer
element values. This allows us to unify the both callbacks as well as
dropping the no longer used reset_resume field, which ends up with a
good code reduction.
A slight behavior change by this patch is that now we assign
restore_mixer_value() as the default resume callback, and the function
is no longer called at reset-resume when the resume callback is
overridden by the quirk function. That is, if needed, the quirk
resume function would have to handle similarly as
restore_mixer_value() by itself.
Reported-by: En-Shuo Hsu <enshuo@chromium.org>
Cc: Yu-Hsuan Hsu <yuhsuan@chromium.org>
Link: https://lore.kernel.org/r/CADDZ45UPsbpAAqP6=ZkTT8BE-yLii4Y7xSDnjK550G2DhQsMew@mail.gmail.com
Link: https://lore.kernel.org/r/20210910105155.12862-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This adds a second mixer control to Digidesign Mbox
to select between Analog/SPDIF capture.
Users will note that selecting the SPDIF input source
automatically switches the clock mode to sync to SPDIF,
which is a feature of the hardware.
(You can change the clock source back to internal if you want
to capture from spdif but not sync to its clock although this mode
is probably not recommended).
Unfortunately, starting the stream resets both modes
to Internally clocked and Analog input mode.
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Tested-by: Damien Zammit <damien@zamaudio.com>
Link: https://lore.kernel.org/r/20210813113402.11849-1-damien@zamaudio.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add initial support for the Focusrite Scarlett Solo and 2i2 devices:
- They have no mixer
- They don't support reporting sync status or levels
- The configuration space is laid out differently to the other models
- There is no level (line/inst) switch on input 1 of the Solo
Co-developed-by: Vladimir Sadovnikov <sadko4u@gmail.com>
Signed-off-by: Vladimir Sadovnikov <sadko4u@gmail.com>
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/190b90f6f1f8f8d4dfb5f0a7761ff8ae5c40fdde.1624379707.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add separate init function to call the existing controls_create
function so a custom error can be displayed if initialisation fails.
Use info level instead of error for notifications.
Display the VID/PID so device_setup is targeted to the right device.
Display "enabled" message to easily confirm that the driver is loaded.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/b5d140c65f640faf2427e085fbbc0297b32e5fce.1621584566.git.g@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patchset tries to resolve the diversity in the audio LED
control among the ALSA drivers. A new control layer registration
is introduced which allows to run additional operations on
top of the elementary ALSA sound controls.
A new control access group (three bits in the access flags)
was introduced to carry the LED group information for
the sound controls. The low-level sound drivers can just
mark those controls using this access group. This information
is not exported to the user space, but user space can
manage the LED sound control associations through sysfs
(last patch) per Mark's request. It makes things fully
configurable in the kernel and user space (UCM).
The actual state ('route') evaluation is really easy
(the minimal value check for all channels / controls / cards).
If there's more complicated logic for a given hardware,
the card driver may eventually export a new read-only
sound control for the LED group and do the logic itself.
The new LED trigger control code is completely separated
and possibly optional (there's no symbol dependency).
The full code separation allows eventually to move this
LED trigger control to the user space in future.
Actually it replaces the already present functionality
in the kernel space (HDA drivers) and allows a quick adoption
for the recent hardware (ASoC codecs including SoundWire).
snd_ctl_led 24576 0
The sound driver implementation is really easy:
1) call snd_ctl_led_request() when control LED layer should be
automatically activated
/ it calls module_request("snd-ctl-led") on demand /
2) mark all related kcontrols with
SNDRV_CTL_ELEM_ACCESS_SPK_LED or
SNDRV_CTL_ELEM_ACCESS_MIC_LED
Link: https://lore.kernel.org/r/20210317172945.842280-1-perex@perex.cz
Signed-off-by: Takashi Iwai <tiwai@suse.de>
-----BEGIN PGP SIGNATURE-----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=1uM7
-----END PGP SIGNATURE-----
Merge tag 'tags/mute-led-rework' into for-next
ALSA: control - add generic LED API
This patchset tries to resolve the diversity in the audio LED
control among the ALSA drivers. A new control layer registration
is introduced which allows to run additional operations on
top of the elementary ALSA sound controls.
A new control access group (three bits in the access flags)
was introduced to carry the LED group information for
the sound controls. The low-level sound drivers can just
mark those controls using this access group. This information
is not exported to the user space, but user space can
manage the LED sound control associations through sysfs
(last patch) per Mark's request. It makes things fully
configurable in the kernel and user space (UCM).
The actual state ('route') evaluation is really easy
(the minimal value check for all channels / controls / cards).
If there's more complicated logic for a given hardware,
the card driver may eventually export a new read-only
sound control for the LED group and do the logic itself.
The new LED trigger control code is completely separated
and possibly optional (there's no symbol dependency).
The full code separation allows eventually to move this
LED trigger control to the user space in future.
Actually it replaces the already present functionality
in the kernel space (HDA drivers) and allows a quick adoption
for the recent hardware (ASoC codecs including SoundWire).
snd_ctl_led 24576 0
The sound driver implementation is really easy:
1) call snd_ctl_led_request() when control LED layer should be
automatically activated
/ it calls module_request("snd-ctl-led") on demand /
2) mark all related kcontrols with
SNDRV_CTL_ELEM_ACCESS_SPK_LED or
SNDRV_CTL_ELEM_ACCESS_MIC_LED
Link: https://lore.kernel.org/r/20210317172945.842280-1-perex@perex.cz
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Rear Mic on Lenovo P620 cannot record after S3, despite that there's no
error and the other two functions of the USB audio, Line In and Line
Out, work just fine.
The mic starts to work again after running userspace app like "alsactl
store". Following the lead, the evidence shows that as soon as connector
status is queried, the mic can work again.
So also check connector value on resume to "wake up" the USB audio to
make it functional.
This can be device specific, however I think this generic approach may
benefit more than one device.
Now the resume callback checks connector, and a new callback,
reset_resume, to also restore switches and volumes.
Suggested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20210325165918.22593-2-kai.heng.feng@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The shifting of the u8 integer device by 24 bits to the left will
be promoted to a 32 bit signed int and then sign-extended to a
64 bit unsigned long. In the event that the top bit of device is
set then all then all the upper 32 bits of the unsigned long will
end up as also being set because of the sign-extension. Fix this
by casting device to an unsigned long before the shift.
Addresses-Coverity: ("Unintended sign extension")
Fixes: a07df82c79 ("ALSA: usb-audio: Add DJM750 to Pioneer mixer quirk")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210318132008.15266-1-colin.king@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Unlike the other DJM, the value to set the "CD/LINE" and "LINE" capture
control options are inverted. This fix makes sure that the displayed
info label while using `alsamixer` matches the input switches label
on the DJM-850 mixer.
Signed-off-by: Nicolas MURE <nicolas.mure2019@gmail.com>
Link: https://lore.kernel.org/r/20210301152729.18094-5-nicolas.mure2019@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds mixer quirks for the Pioneer DJM-900NXS2 mixer. This
device has 6 capture channels, 5 of them allow setting the signal
source. This adds controls for these, similar to the DJM-250Mk2.
However, playpack channels are not controllable via software like on the
250Mk2, as they can only be set manually on the mixing console.
Read-only controls showing the currently selected playback channels are
omitted.
Signed-off-by: Fabian Lesniak <fabian@lesniak-it.de>
Link: https://lore.kernel.org/r/20210205215116.258724-2-fabian@lesniak-it.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This allows for N different devices to use the pioneer mixer quirk for
setting capture/record type and recording level. The impementation has
not changed much with the exception of an additional mask on
private_value to allow storing of a device index:
DEVICE MASK 0xff000000
GROUP_MASK 0x00ff0000
VALUE_MASK 0x0000ffff
This could be improved by changing the arrays of wValues for each
channel to contain named definitions (e.g. SND_DJM_CAP_LINE). It would
improve readability and perhaps would allow using the same array for
multiple channels. The channel number can be specified on the control
next to the wIndex.
Feedback is very much appreciated as I'm not the most proficient C
programmer but am learning as I go.
Signed-off-by: Olivia Mackintosh <livvy@base.nu>
Link: https://lore.kernel.org/r/20210205184256.10201-2-livvy@base.nu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
strlcpy is deprecated. see: Documentation/process/deprecated.rst
Change the calls that do not use the strlcpy return value to the
preferred strscpy.
Done with cocci script:
@@
expression e1, e2, e3;
@@
- strlcpy(
+ strscpy(
e1, e2, e3);
This cocci script leaves the instances where the return value is
used unchanged.
After this patch, sound/ has 3 uses of strlcpy() that need to be
manually inspected for conversion and changed one day.
$ git grep -w strlcpy sound/
sound/usb/card.c: len = strlcpy(card->longname, s, sizeof(card->longname));
sound/usb/mixer.c: return strlcpy(buf, p->name, buflen);
sound/usb/mixer.c: return strlcpy(buf, p->names[index], buflen);
Miscellenea:
o Remove trailing whitespace in conversion of sound/core/hwdep.c
Link: https://lore.kernel.org/lkml/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/22b393d1790bb268769d0bab7bacf0866dcb0c14.camel@perches.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch extends support for DJM-250MK2 and allows mapping
playback and capture channels to available sources.
Configures the card through USB commands.
Signed-off-by: František Kučera <franta-linux@frantovo.cz>
Link: https://lore.kernel.org/r/20200922144206.10472-1-konference@frantovo.cz
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adds an entry for Creative USB X-Fi to the rc_config array in
mixer_quirks.c to allow use of volume knob on the device.
Adds support for newer X-Fi Pro card, known as "Model No. SB1095"
with USB ID "041e:3263"
Signed-off-by: Mirko Dietrich <buzz@l4m1.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200806124850.20334-1-buzz@l4m1.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The USB-audio mixer code holds a linked list of usb_mixer_elem_list,
and several operations are performed for each mixer element. A few of
them (snd_usb_mixer_notify_id() and snd_usb_mixer_interrupt_v2())
assume each mixer element being a usb_mixer_elem_info object that is a
subclass of usb_mixer_elem_list, cast via container_of() and access it
members. This may result in an out-of-bound access when a
non-standard list element has been added, as spotted by syzkaller
recently.
This patch adds a new field, is_std_info, in usb_mixer_elem_list to
indicate that the element is the usb_mixer_elem_info type or not, and
skip the access to such an element if needed.
Reported-by: syzbot+fb14314433463ad51625@syzkaller.appspotmail.com
Reported-by: syzbot+2405ca3401e943c538b5@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200624122340.9615-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As reported by kbuild test robot, mixer quirks for RME Babyface
Pro used plain integer instead of NULL.
Fixes: 3e8f3bd047 ("ALSA: usb-audio: RME Babyface Pro mixer patch")
Signed-off-by: Thomas Ebeling <penguins@bollie.de>
Reported-by: kbuild test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20200529173248.zzawijfvw73kzjxt@bollie.ca9.eu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_microii_spdif_default_get() invokes snd_usb_lock_shutdown(), which
increases the refcount of the snd_usb_audio object "chip".
When snd_microii_spdif_default_get() returns, local variable "chip"
becomes invalid, so the refcount should be decreased to keep refcount
balanced.
The reference counting issue happens in several exception handling paths
of snd_microii_spdif_default_get(). When those error scenarios occur
such as usb_ifnum_to_if() returns NULL, the function forgets to decrease
the refcnt increased by snd_usb_lock_shutdown(), causing a refcnt leak.
Fix this issue by jumping to "end" label when those error scenarios
occur.
Fixes: 447d6275f0 ("ALSA: usb-audio: Add sanity checks for endpoint accesses")
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1587617711-13200-1-git-send-email-xiyuyang19@fudan.edu.cn
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added mixer quirks to allow controlling the internal DSP of the
RME Babyface Pro and its successor Babyface Pro FS.
Signed-off-by: Thomas Ebeling <penguins@bollie.de>
Link: https://lore.kernel.org/r/20200414211019.qprg7whepg2y7nei@bollie.ca9.eu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds support for Presonus Studio 1810c, a usb interface
that's UAC2 compliant with a few quirks and a few extra hw-specific
controls. I've tested all 3 altsettings and the added switch
controls and they work as expected.
More infos on the card:
https://www.presonus.com/products/Studio-1810c
Note that this work is based on packet inspection with
usbmon. I just wanted to get this card to work for using
it on our open-source radio station:
https://github.com/UoC-Radio
v2 address issues reported by Takashi:
* Properly get/set enum type controls
* Prevent race condition on switch_get/set
* Various control naming changes
* Various coding style fixes
v3 improve readability of sample rate filtering
and some other minor changes.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Link: https://lore.kernel.org/r/5e47481a.1c69fb81.befb3.8dac@mx.google.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
GCC reports the following warning with W=1
sound/usb/mixer_quirks.c: In function ‘snd_microii_controls_create’:
sound/usb/mixer_quirks.c:1694:2: warning: ‘static’ is not at beginning
of declaration [-Wold-style-declaration]
1694 | const static usb_mixer_elem_resume_func_t resume_funcs[] = {
| ^~~~~
Move static to the beginning of declaration
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200111214736.3002-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Apply const prefix to the remaining places: the static table for the
unit information, the mixer maps, the validator tables, etc.
Just for minor optimization and no functional changes.
Link: https://lore.kernel.org/r/20200105144823.29547-12-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Most of snd_kcontrol_new definitions are read-only and passed as-is.
Let's declare them as const for further optimization.
There should be no functional changes by this patch.
Link: https://lore.kernel.org/r/20200103081714.9560-42-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
